Search Results

Search found 10207 results on 409 pages for 'ethernet switch'.

Page 312/409 | < Previous Page | 308 309 310 311 312 313 314 315 316 317 318 319  | Next Page >

• Cisco SA520 to Adtran 1234 no DHCP transfer

  - by Grico

  I am trying to set up a Cisco SA520 to run DHCP on my network. I have a vendor provided switch, the Adtran 1234, and it provides DHCP for our phone systems on VLAN 200. I do not have access to the Adtran, but the vendor gave me a IP on port 1 for WAN and said port 2 should be for the "trust" side should go. I did setup a mini lab where, Adtran 1 went to SA520 WAN port, and SA520 trust 1 went to my laptop. Everything worked fine, I could ping and get internet using the DHCP scope I put on the SA520. I then unplugged my computer from SA520 trust 1 and plugged it into Adtran 2. I plugged my computer into Adtran 23 and I dont get DHCP or even a link light. If I restart my machine, I get a brief link and then it dies once the machine boots. I have tried several ports on the Adtran and none seem to work. Different cables as well. However, when I plug a phone into the Adtran, the phone boot immediately and shows link. Thoughts?

  Read the article

• Powershell: Execute exe on remote server and capture output

  - by user364825

  I am trying to script the execution of an installer on remote web servers. The installer in question is also a Windows Service that hosts NServiceBus. If RDP'd into the server, the application is installed by the following command: &"$theInstaller" /install /serviceName:TheServiceName The installer prints output about its progress registering the service and connecting to the database to stdout, among other things. This works fine from an RDP session, but when I execute it remotely via PS, I get a you-can't-do-this-over-the-network message if I execute it directly or via Invoke-Command -computername $theRemoteServer: System.IO.FileLoadException: Could not load file or assembly 'file://\\theRemoteServer\c$ \thePath\AutoMapper.dll' or one of its dependencies. Operation is not supported. (Exception from HRESULT: 0x80131515) --- System.NotSupportedException: An attempt was made to load an assembly from a network location which would have caused the assembly to be sandboxed in previous versions of the .NET Framework. This release of the .NET Framework does not enable CAS policy by default, so this load may be dangerous. If this load is not intended to sandbox the assembly, please enable the loadFromRemoteSources switch. See http://go.microsoft.com/fwlink/?LinkId=155569 for more information. (Note: I added an additional "\" to the path in the first line in order to get it to show up correctly in the preview on this site.) This, and other DLLs, are loaded by the service, and the service's execution context cannot, apparently, be remotified. I have also tried using Invoke-WmiMethod, which does something, but it's not clear what, and the output from the installer is lost: Invoke-WMIMethod win32_process create '"$theInstaller" /install /serviceName:TheServiceName' -ComputerName $server (with and without cmd.exe /k before the intaller reference): __GENUS : 2 __CLASS : __PARAMETERS __SUPERCLASS : __DYNASTY : __PARAMETERS __RELPATH : __PROPERTY_COUNT : 2 __DERIVATION : {} __SERVER : __NAMESPACE : __PATH : ProcessId : ReturnValue : 9 How does one remotely execute such an EXE and capture the output? Thanks!

  Read the article

• Sync desktop Mac environment to laptop

  - by Andrew Vit

  I spend the majority of my time working at my desktop Mac, which I have configured for my web development environment. My spouse has a MacBook for casual use, and I occasionally steal it back when I need to work off-site, or when travelling. The question is how to best synchronize the two so I can switch between them more readily. I've solved a few obvious things by using online services: Email is hosted on IMAP. Working files are in Dropbox. Source code is managed in git. However, the following are things I always miss when jumping on the laptop: Installed Applications (current versions) Installed libraries & utilities (/usr/local) Apache VirtualHosts & other configurations (/etc) Disk image files for VMs My current method is to connect the MacBook via Firewire target mode and rsync the /Users/me home directory, and then cherry-pick the other items I need from Applications, /etc and /usr/local. The problem with this method is that it can be very time consuming due to things like my virtual machine image files, cached emails, etc. How can I make this faster & easier? Can you recommend a solution for configuration management (so I can repeatably install & configure the same software on both), or synchronization (so I can bring the MacBook up to date nightly, over our home network)?

  Read the article

• Options for synchronizing Palm Desktop calendars

  - by Al Everett

  My wife and I each have Palm Centro phones and very full calendars. We've been using Palm products for years and are happy with them and are not looking to switch (and don't have the budget for it even if we wanted to). What is a viable way we can synchronize our calendars? Back when we had Palm Z22s we used AirSet. It worked great in synchronizing our desktop calendars. Unfortunately, their sync software does not support Palm Desktop v6 and there is nothing in the pipeline to support it. (The third party vendor is apparently not interested in updating for the newer Palm desktop.) I would love to be able to get back to having each other's appointments appear on the other's calendar. What can we do? Some limitations: A data plan is not an option (so this precludes over-the-air synchronization options) No Microsoft Outlook Edit: Syncing my Palm to my Palm Desktop is not the issue. Being able to sync, in some way, the Palm calendar databases of my wife's and my calendars is what's desired.

  Read the article

• Software for handling camera RAW-files

  - by Eikern

  I use a digital SLR as most other photographers do today and have quickly realised that capturing images using camera-RAW files is the way to go. Personally I use Adobe Lightroom to handle my photo library, but I know there are other software available like Apple Aperture. These applications are quite hard to use for a novice, and are quite expensive too. I've often recommended other photographers to switch to camera-raw, but they won't do it because Windows can't handle it natively. Are there any free or cheaper applications out there that can do simple file handling and adjustments? Preferably so simple that my mom can do it. I know Nikon offers a codec that allows you to view NEF-files natively inside Windows, but still limits the uses of the file and slows the system down if the file is big. Does anybody know of a drag-and-drop application that converts camera-raw to JPG on-the-fly? In case I or someone would need to upload an image to the web or use it inside a word-document. Thanks.

  Read the article

• NetBackup prefers "Scratch" tapes over dedicated tapes

  - by wfaulk

  I have a NetBackup 6.0MP7 installation running on Windows Server 2003. It functions as the only Master Server and Media Server. I swap a full set of tapes in and out every week, but leave a set of tapes with their Volume Pool set to "Scratch" in all the time. The weekly tape sets then get rotated back in after a period of time. Largely, this works fine. I seldom actually need the scratch tapes, but every once in a while, a backup will run over what I have dedicated to the task. However, one week's set of tapes consistently gets declined in favor of the scratch pool. The backup policies are the same for every week, they all have "Policy Volume Pool" set to "NetBackup", and all of the tapes for every week (beside the scratch tapes) have had their pools assigned as "NetBackup", definitely including the week that always gets ignored. That said, it doesn't ignore all of the NetBackup pool tapes for that week. It does usually write to two or three of them, but it writes to like 20 of the scratch tapes. (I haven't thought to look to see if it's always the same two or three tapes.) And this problem never seems to occur for any other week. It doesn't load the tapes and then reject them; it never seems to try to use them at all. They are not flagged as frozen. They are all active and unassigned when I swap them in. The tapes are in a Quantum PX510 tape library. The NetBackup server is attached to the library/robot via fibrechannel going through an HP-branded Brocade switch. I'm not an expert on NetBackup at all. I don't really even know where to look. Any advice on logs to look at or logging to enable or really anything at all would be appreciated. I'll keep an eye on the question and update it if anyone needs any more info to help.

  Read the article

• Cannot print certain colours on Ubuntu with HP Laser Printer

  - by ILMV

  We have a load of machines running Ubuntu in our office, they are either on 8.04 or 9.10. We have a server which connects a HP JetDirect that connects to a HP 3550 Colour Laser printer using CUPS. The problem we are having is we cannot print red, magenta or yellow at 100%, I've got a picture of the Ubuntu test page to demonstrate my problem: This is obviously a pretty big problem as we are constantly receiving documents with these colours and cannot successfully print them off, we cannot just switch the grayscale, our business depends on being able to print colour (seems trivial but we handle lots of artwork). We're using the recommended driver HP Color LaserJet 3550 footmatic/pxljr (recommended), there is another driver in the list labelled HP Color LaserJet 3550 footmatic/hpijs. These are production printers so need to make sure any setting change won't kick is in the nuts. It would appear HPIJS is for HP Inkjets, makes sense I guess. The problem doesn't occur in Windows. RESOLVED I've managed to solve the problem, I did indeed use the HPIJS driver (apparently for inkjets) but it seems to have worked, we're going to roll with it for now to see how we get on with it.

  Read the article

• DHCP forwarding behind access list on a Cisco Catalyst

  - by Ásgeir Bjarnason

  I'm having some trouble with forwarding DHCP from a subnet behind an access list on a Cisco Catalyst 4500 switch. I'm hoping somebody can see the mistake I'm making. The subnet is defined like this: (first three octets of IP addresses and vrf name anonymized) interface Vlan40 ip vrf forwarding vrf_name ip address 10.10.10.126 255.255.255.0 secondary ip address 10.10.10.254 255.255.255.0 ip access-group 100 out ip helper-address 10.10.20.36 no ip redirects I tried turning on a VMWare machine on this subnet that was configured to use DHCP, but I never got a DHCP response and the DHCP server didn't receive a request. I tried putting the following in the access-list: access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootps access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootpc access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootps access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootpc That didn't help. Can anybody see what the problem is? I know that the DHCP server works; our whole network is running off of this DHCP server I also know that the subnet works because we have active servers running on the network The DHCP scope is already defined on the DHCP server The subnet is correctly defined on the VMWare server (already servers running on the subnet on VMWare) Edit 2012-10-19: This is solved! The subnet had formerly been defined as a /25 network, but was then expanded into a /24 network. When the DHCP scope was altered after this change it was done incorrectly; the gateway was moved to .254, the leasable IP range was in the lower half of the /24 subnet but we forgot to change the CIDR prefix from /25 into /24. This happened some 2 years ago, and we didn't need to use DHCP on this server network again until this week. Thank you MDMarra and Jason Seemann for looking at the question and trying to troubleshoot. Now I'm wondering if I should mark Jason's answer as the accepted answer (I am new to the Stack Exchange network, so I don't know the etiquette of what to do if I misstated the question like in this case).

  Read the article

• Toshiba laptop cd drive read causes OS to totally freeze

  - by Fujishiro

  Okay I'll try to write an understandable summary. Forgive me if I'll fail with that attempt though. So. There is a Toshiba Satellite notebook. Got Windows 7 x86 Professional (OEM) installed on it, everything is fine (okay.. somewhat). The problem. If you put an audio or any kind of disc into the drive, something starts to eat the PC. Back then when the owner told me about this, he put an audio disc into the lappy. Winamp caused the IO load, 100%. Tried taskkill, taskkill /T, tried powershell, EVERYTHING. You just can NOT kill winamp or anything which becomes the blocker at that time. Even if you kill almost everything, laptop won't do a clear shutdown. Also I tried to use the force switch at 'shutdown' from cmd, but no use. (So: At these times you can use the laptop, but the blocker/explorer/disc becomes gray as a non-responding app. You can try to kill them, but that won't work, nor you can shutdown the machine). (Also tried using PID, but no use. For the highest IO I used the "select columns" from Task Manager and enabled the IO columns.) My first hunch was the problematic disc, autoplay and it tries to read tries to read (still shouldn't kill the PC). Disabled autoplay, removed winamp. Tried other software, etc. Everything was ok. Few days later the owner tried to put a disc into the machine and it started to reproduce the same symptoms but with a totally different disc. Uhm what to know. Virus is not an option, protected by BitDefender (valid license) and Spybot. Thanks if you have ANY idea about this strange problem. ps.: For now, the owner uses Daemon tools + Blindwrite as an alternative for those apps which wouldnt start without the disc.

  Read the article

• Completely automated DVD insert-rip-compress-eject workflow

  - by Kevin L.

  (Partially inspired by this question.) Background: I have a PC hidden away behind an HD LCD in custom-built entertainment center. The only visible part of the PC is an external DVD drive, mounted above the Wii. The PC happens to have Windows XP on it; Hackintoshing and Linux might be possible, but I've had issues with drivers for the sound card before. Let's just assume that OS X and Linux are a no-go unless they provide a truly awesome and simple solution for this particular problem. Goal: I would like to have a completely automated workflow for ripping DVDs. Something like this: Push the eject button on the DVD drive, insert the DVD. PC recognizes that this is a video DVD (as opposed to data). PC rips DVD to hard drive. PC finishes ripping, and ejects the DVD tray. PC compresses DVD image into some format that an Xbox 360 can read. PC copies finished compressed video file to a particular folder, so that it can be read into a WMP11 library and seamlessly played by the Xbox 360. PC cleans up all temporary files. Done. The impetus to have this be completely automated is that I’ll never need to switch the TV to the PC’s input and fiddle with the wireless keyboard. That’s just needless user intervention. The UI doesn’t have to be pretty. Nor do I care about speed. And I can probably bridge several of the gaps with some creative Perl use. But it seems likely that many (or all) of the parts should already exist. Any thoughts?

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• SQL Server on Linux

  - by TimothyAWiseman

  For a particular project that is coming up, I am trying to expand my knowledge of Linux, so I am going to set up a Linux system at home. Rather than dual booting, I am thinking about putting SQL Server on a Windows Virtual Machine with Linux as the host at least until this project is over when I will probably switch back to Linux. So, I have a couple of different, but interrelated questions: How well does this work? This is only a test machine at home, so I can easily accept a fair bit of degradation, but if it is going to be a horrible reduction in performance I will dual boot instead. Is there a particular virtual machine manager I should look at to go this route? Since this is my personal machine, price is an issue but I am quite happy to pay a reasonable amount. And finally, given the choice of VMM, is there a particular Linux Distro I should be looking at? [This has been cross posted at Ask.SqlServerCentral.com . I think it may be appropriate at both sites. ]

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing. EDIT: If I currently have been trying: sudo route flush sudo route add default 192.168.19.1 This gets everything to work for about a minute. But after such minute it "forgets" the routing to WiFi while retaining LAN's (en0) routing. If I unplug and replug my LAN (en0) cable, the process works for another minute.

  Read the article

• Networking Home Office

  - by Matt

  I'm in the process of building an office in my garden. It's about 25m away from my house. I'd like to run a wired network connection to the office. I'd rather not go down the powerline route, as speeds don't seem great, and I'm likely to want to be moving a lot of data around on the internal network. I have an electrician who is running armoured electrical cable to the office, and is providing conduit for me to run network cable. My questions are: 1) What type of cable to run 2) How I terminate/connect it at both ends I could get something like armoured cat6 utp solid core (like this: http://www.netstoredirect.com/cat6-cable/289166-external-armoured-cat6-utp-solid-cable-price-per-metre.html) which seems fairly robust, but then I have to terminate it. Additionally, where the cable enters my house, there is about another 15m to where my router is situated. I also read this artice: http://www.audioholics.com/audio-video-cables/bjc-cat-network-cable-quality-interview which scared me into realising I don't know what I'm doing!! particularly with termination. Or I could get an "cat6 external patch cable" (e.g http://www.netstoredirect.com/rj45-network-cables/239231-external-cat6-utp-ldpe-rj45-patch-leads.html) and run that in the conduit, and work out how to terminate it at the house end. At the office end I guess I can just plug it into a switch. Any help? Thanks

  Read the article

• What is the correct iptables rule when NATing multiple private subnets?

  - by Jose Mendez

  I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

  Read the article

• Is there a way to "burn" audio to an ISO? (as an audio CD)

  - by Sootah

  I have an audiobook that I've downloaded via their download manager, and it's loaded into their cutesy little audio program that they force you to use. I can play the book just fine using their proprietary software, and while it's annoying when using my PC, it's utterly UNBEARABLE when I try to listen to it on my Blackberry. The program is INSANELY slow, it literally takes around 30 seconds to switch between tracks, so if I've forgotten where I am in the book it takes me around 15 minutes to finally get to where I was at. I've looked everywhere on how to transcode the book to .MP3, but evidently with their current format it's either extremely convoluted (and I have no desire to dick around with installing some older version of the codec, getting a different transcoding app, and then wrestling with getting it to actually work). Since I'm able to burn a copy of the book to an audio CD, I figure the best way to go about this is to just make the CDs and then rip them off of those to .MP3. In order to avoid wasting two hours, not to mention 14 CD-R's, I was wondering if there's a way to "burn" to an .ISO instead of an actual CD-R. I currently have SlySoft's Virtual CloneDrive installed, so I can mount .ISO's easily enough, but now I want to actually create an ISO via the CD burning process. Just in case I've not explained myself very well, here is an overview of what I intend to do: "Burn" a set of Audio CD .ISOs from the audiobook (hopefully I can do this using Windows Media Player, otherwise I'll be forced to use the audiobook app) Mount an .ISO in Virtual CloneDrive Rip the audio tracks on the mounted .ISO to .MP3s Repeat steps 2-3 until the entire book is in .MP3 format Copy .MP3s to my Blackberry so that I'm not driven insane every time I want to listen to the book in the car, and be able to use Winamp when listening on my computer EDIT: I'd suppose a rather concise way to put it is that I need something that will emulate a CD-R drive, so that you can select it as the output drive in whatever app your burning the audio CD from. (I'd suppose that when you "insert a blank CD-R" the app would then ask you what file to save to)

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• Apache 2.4 Prefork vs. PHP-FPM Event shows sig decrease in requests per second

  - by Mark

  On my Apache 2.4.2 server with a standard mod_php Prefork setup these are my server-status results Current Time: Wednesday, 24-Oct-2012 19:36:24 CDT Restart Time: Wednesday, 24-Oct-2012 01:27:30 CDT Parent Server Config. Generation: 1 Parent Server MPM Generation: 0 Server uptime: 18 hours 8 minutes 54 seconds Total accesses: 14304233 - Total Traffic: 342.3 GB CPU Usage: u12584.6 s721.93 cu.66 cs3.43 - 20.4% CPU load 219 requests/sec - 5.4 MB/second - 25.1 kB/request 507 requests currently being processed, 355 idle workers ______KKKKR_K______W_KKC___CKK_K_K_W__CC_KKK_KK._K_K_KK._KKKK_K_ K_____KK_KKKK_K_KK__K___KK_K___K_____CKKK_WK_K_____KCKK__K___K_K K_CK_K_K_____K__KKKK_K__K___K_KK_K_K_KKKCK____________KK_CK__KKK __C_KKKKKKK___CK___C_KKK_K__C__K_CK____KKK__K__K__K_K__KK_CK_K__ _KKKKK_K_W__KK______K___K__W___C_K__K____KKKKKKKK.KKKKKKKCK_K___ _C_KK_K_WK__K_KK__K__RK_KK___K____K_KK_K_K___RKC_KKKK___KKKC_K_W _C_KK_KK__W____KC__KKK__KKK___K___KKK_KK_K_KKW__K_KR_KK_KK__KKK_ R__KKK__KKKKKK__K_KKKKK_K__K_K___KKW_________KK_K___KKK___KK.K_C KKKKKKW_____K__K_KKC_KCKK_K_KK_K__KK__K___K__KK_KK__________KK__ __K___KK_K__K_C_KK_K___KK__KK__K__KCK_K__KK_________K_K_KK__.K__ K_CKK.CCRW__KKKKKKKKKKKC__W____K___KWK_KK_KKC______.K_K_KK_KKKC_ __KKK_W_KCKKK_K_K____CCCK__KC_KKKK_K____K_CK_K____K__K____KKK_KK KK___K_K_K__KW__KCKKKK____WKWK__K_KKRKK__C_K_KK_KK_K__KKCC_K__C_ KK_K___K_KK______K_____CKK_K_______KK_CKCK__KKKKK____K__K..K____ __KKWK_KW__KKK__K_KKK___K_KK_KKK__KK___KK___KK_KK___KK____KKWKKC KK_KKKK_................................` When I switch to a PHP-FPM setup with the Event MPM with no other variables changes, my requests/sec plummet and overall apache response is garbage. Current Time: Wednesday, 24-Oct-2012 19:51:21 CDT Restart Time: Wednesday, 24-Oct-2012 19:48:03 CDT Parent Server Config. Generation: 1 Parent Server MPM Generation: 0 Server uptime: 3 minutes 18 seconds Total accesses: 18720 - Total Traffic: 307.1 MB CPU Usage: u16.57 s4.74 cu0 cs0 - 10.8% CPU load 94.5 requests/sec - 1.6 MB/second - 16.8 kB/request 15 requests currently being processed, 49 idle workers PID Connections Threads Async connections total accepting busy idle writing keep-alive closing 11701 114 no 10 22 0 66 38 11702 134 no 5 27 0 81 48 Sum 248 15 49 0 147 86 __R_R__W___RRW________RR__R___W_W_______W_____W_____________R_R_ Is there any obvious reason anyone could think of why this would be the case. I can provide any other additional stats or server setup info to help out. Ive tried tweaking everything up and down and nothing really helps get the PHP-FPM setup anywhere near a baseic prefork/mod-php setup. Thanks!

  Read the article

• Multiple cable adapter setup not working - VGA to smartphone. All cables tested and work

  - by Christopher Rucinski

  Issue Pictured overhead projector setup does not work. #1 - #2 - #3 - Phone. All cables are tested and work! The issue is the HDMI connection between cable #2 and #3. With all other cables, the screen will automatically be displayed onto the projector screen. No extra work needed. With the pictured setup, the smartphone screen is not displayed onto the projector screen. What is the issue with the HDMI connection?? Background We recently had to do presentations at work (school), but the administration only provided VGA means of hooking up to it. Mostly likely reason probably dealt with cost. Anyways, there are several teachers that have brand new Samsung Series 9 ultrabooks (or similar). You know, the ones without VGA support. So I bought an adapter for those ultrabooks. Cable #5 in the picture below. However, both my coworker and I have been wanting to just display our phone screens on the projector. This I knew would require some extra work. What I have VGA cable to projector (cables go through the wall) For laptops HDMI to VGA cable For laptops MHL adapter For 11-pin microUSB phones microHDMI to VGA cable For ultrabooks 11-pin to 5-pin microUSB adapter For older 5-pin microUSB phones) Equipment Projectors 1 projector with VGA and HDMI input (issue is coworkers forget to switch sources) 1 projector with VGA only input Laptops 2 new Samsung ultrabooks w/o VGA or HDMI support 1 ultrabook with VGA and HDMI support several other laptops with at least VGA support 1 tablet with 11-pin microUSB at least 1 new phone with 11-pin microUSB at least 1 old phone with 5-pin microUSB Tested VGA cable (#1) to laptop Good VGA cable (#1) to HDMI adapter (#2) to laptop Good VGA cable (#1) to microHDMI adapter (#5) to laptop Good Projector to HDMI cable (not shown) to MHL adapter (#3) to Galaxy Note 3 smartphone Good VGA cable (#1) to HDMI adapter (#2) to MHL adapter (#3) to Galaxy Note 3 smartphone Does not work!! Extra Notes The 11-pin MHL adapter will not fit inside the 11-pin to 5-pin microUSB adapter so older phones can be displayed on the screen.

  Read the article

• Force SSL on one page via .htaccess without looping

  - by Will Martin

  Okay, I have this code: RewriteCond %{HTTPS} off RewriteCond %{REQUEST_URI} ^/borrowing/ill/request\.php$ RewriteRule ^.*$ https://%{HTTP_HOST}%{REQUEST_URI} [R,L] The way I would expect this to work is: A request for /borrowing/ill/request.php comes in on HTTP. The rule matches. The server redirects to HTTPS. The rule does not match, because HTTPS is now on. The way it actually works is: A request for /borrowing/ill/request.php comes in on HTTP. The rule matches. The server redirects to HTTPS. The rule matches. The server redirects to HTTPS. The rule matches. The server redirects to HTTPS ... And so on. I know that the second condition (matching the file name) is working, because the redirect loop only hits that specific page. The question is, why isn't the switch to HTTPS causing the first condition to not match? EDIT: I put the exact same .htaccess rules into a test area on another server -- same file and path info. And they worked just fine. There's got to be something wrong with the server configuration elsewhere.

  Read the article

• Why do I get this message from chrome when navigating to https://www.amazon.com?

  - by Denis

  This is probably not the site you are looking for! You attempted to reach www.amazon.com, but instead you actually reached a server identifying itself as *.voxcdn.com. This may be caused by a misconfiguration on the server or by something more serious. An attacker on your network could be trying to get you to visit a fake (and potentially harmful) version of www.amazon.com. Intermittently, I get a blank page when going to http://www.amazon.com. So I stuck an 's' in the URL, making it https://www.amazon.com and got that message above (with the nice red screen) from Chrome indicating there might be some monkey business going on. After hammering on the URL a bunch of times and pulling it up in Chrome's developer tool to look at the network traffic on it, the url (without the s) started behaving. The url with the s just hangs, but the red screen no longer comes up. Some specs... I've got a macBook Pro, Snow Leopard, Time Warner cable. I've had enough strange stuff happening over the past couple months (google.com, youtube.com, amazon.com not coming up or loading strange error messages with random reference numbers) that I finally decided to switch to OpenDNS. Still having problems, though.

  Read the article

• connect server to server on secondary NIC

  - by microchasm

  Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

  Read the article

• How to keep Ubuntu 11.10 and Kate editor w/terminal from changing command line when changing tabs?

  - by Kairan

  I am programming C using Kate editor in Ubuntu 11.10. It works great, but when I change tabs in Kate, the terminal line changes to the file path of the tab I click on. Normally this is not a big deal (other than annoyingly adding extra text to my terminal) however if I am currently RUNNNING a C program, it obviously will type at the command line, which is not so cool. Example terminal window for my C program (its at a menu): 1) select opt 1 2) select opt 2 Enter choice: (here it waits for prompt from user) Now when I click a tab in Kate, it wants to put in the cd / path of the file in that tab, such as: cd /home/user/os/files And of course since my terminal was waiting for prompt from user it gets that command.. not good. Perhaps there is no fix, but maybe someone knows? Obviously I could choose NOT to switch tabs or end program before switching tabs... Note: I probably made the mistake of putting this under StackOverflow which is more of a programming area - so though repost here might be best (I am not sure how to link the questions but will paste hyperlink to that post - I dont want to violate any stackoverflow/superuser violations) Suggestions on merging them are welcome or if I should delete one? StackOverFlow Question

  Read the article

• RRAS NAT not working on a certain computer

  - by legenden

  This is driving me crazy. I have a virtualized W2K8 server running RRAS. Every other computer or server on the network can access the internet through the NAT except one. On one server, it just won't work. I can ping the ip address of the NAT gateway just fine, and everything else works. (SMB, etc) DNS, which is hosted by the same server, also works just fine. I have even reinstalled the OS on the problem server and it still doesn't work. Recap of the steps I tried: There are 3 network cards in the server, I tried every one and different switch ports. Not a hardware problem. Reinstalled W2K8 R2 on server with the problem, didn't help. Tried the IP of the internet gateway directly - this did work (!). But I need NAT to work. All firewalls are disabled. Removed computer from domain, deleted computer membership in Active Directory Users and Computers and added it back. Disabled all other network adapters and set a static ip and specified the gateway ip manually. When I tracert a public IP, the first hop (or any other hop) comes up as: C:\>tracert www.google.com Tracing route to www.l.google.com [209.85.225.106] over a maximum of 30 hops: 1 * * * Request timed out. 2 * * * Request timed out. From a different computer, on which NAT works, the first hop comes up as: tracert www.google.com Tracing route to www.l.google.com [209.85.225.105] over a maximum of 30 hops: 1 <1 ms * <1 ms xxxx [10.5.1.1] This is the most bizarre problem I ever came across, and I realize that it's a long shot asking it here given all the details, but I'm pulling my hair out. Maybe someone has an idea...

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

< Previous Page | 308 309 310 311 312 313 314 315 316 317 318 319  | Next Page >