Search Results

Search found 8162 results on 327 pages for 'module packaging'.

Page 314/327 | < Previous Page | 310 311 312 313 314 315 316 317 318 319 320 321  | Next Page >

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• Load-balancing between a Procurve switch and a server

  - by vlad

  Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

  Read the article

• Cyrus on CentOS with sasl / pam / ldap

  - by Oscar

  SASL/PAM/LDAP is driving me crazy... that's what I read a lot when googling for problems in this area, and what I experience myself :-S I'm trying to get Cyrus imap working for virtual hosting on CentOS with this authorisation backend and really don't know what's happening. In saslauthd I configured the LDAP search filter to use, but it looks like pam completely ignores it. Here's what I do for testing (done more tests but all with similar results): [root@testserv ~]# imtest -u [email protected] -a [email protected] WARNING: no hostname supplied, assuming localhost S: * OK [CAPABILITY IMAP4 IMAP4rev1 LITERAL+ ID STARTTLS] testserv. Cyrus IMAP4 v2.3.7-Invoca-RPM-2.3.7-7.el5_6.4 server ready C: C01 CAPABILITY S: * CAPABILITY IMAP4 IMAP4rev1 LITERAL+ ID STARTTLS ACL RIGHTS=kxte QUOTA MAILBOX-REFERRALS NAMESPACE UIDPLUS NO_ATOMIC_RENAME UNSELECT CHILDREN MULTIAPPEND BINARY SORT SORT=MODSEQ THREAD=ORDEREDSUBJECT THREAD=REFERENCES ANNOTATEMORE CATENATE CONDSTORE IDLE LISTEXT LIST-SUBSCRIBED X-NETSCAPE URLAUTH S: C01 OK Completed Please enter your password: C: L01 LOGIN [email protected] {6} S: + go ahead C: <omitted> S: L01 NO Login failed: authentication failure Authentication failed. generic failure Security strength factor: 0 C: Q01 LOGOUT * BYE LOGOUT received Q01 OK Completed Connection closed. The LDAP entry does exist (and so does the mailbox in Cyrus): [root@testserv ~]# ldapsearch -WxD cn=Manager,o=mydomain,c=com [email protected] Enter LDAP Password: # extended LDIF # # LDAPv3 # base <> with scope subtree # filter: [email protected] # requesting: ALL # # myuser, accounts, testserv.mydomain.com, mydomain, com dn: uid=myuser,ou=accounts,dc=testserv.mydomain.com,o=mydomain,c=com objectClass: top objectClass: person objectClass: organizationalPerson objectClass: inetOrgPerson objectClass: posixAccount objectClass: shadowAccount uidNumber: 16 uid: myuser gidNumber: 5 givenName: My sn: Name mail: [email protected] cn: My Name userPassword:: dYN5ebB0fXhNRn1pZllhRnJX7Uk= shadowLastChange: 15176 homeDirectory: /dev/null # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 This is what I get in /var/log/messages Aug 2 04:00:11 testserv cyrus/imap[12514]: auxpropfunc error invalid parameter supplied Aug 2 04:00:19 testserv saslauthd[5926]: do_auth : auth failure: [[email protected]] [service=imap] [realm=testserv.mydomain.com] [mech=pam] [reason=PAM auth error] ... /var/adm/auth.log Aug 2 04:00:11 testserv cyrus/imap[12514]: auxpropfunc error invalid parameter supplied Aug 2 04:00:11 testserv cyrus/imap[12514]: _sasl_plugin_load failed on sasl_auxprop_plug_init for plugin: ldapdb Aug 2 04:00:19 testserv saslauthd[5926]: DEBUG: auth_pam: pam_authenticate failed: User not known to the underlying authentication module Aug 2 04:00:19 testserv saslauthd[5926]: do_auth : auth failure: [[email protected]] [service=imap] [realm=testserv.mydomain.com] [mech=pam] [reason=PAM auth error] (AFAIK I can ignore the auxprop msg) ... and /var/log/slapd.log: Aug 2 04:00:19 testserv slapd[5968]: conn=61 fd=27 ACCEPT from IP=127.0.0.1:51403 (IP=0.0.0.0:389) Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=0 BIND dn="" method=128 Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=0 RESULT tag=97 err=0 text= Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=1 SRCH base="o=mydomain,c=com" scope=2 deref=0 filter="([email protected])" Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=1 SEARCH RESULT tag=101 err=0 nentries=0 text= Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=2 UNBIND Aug 2 04:00:19 testserv slapd[5968]: conn=61 fd=27 closed These are the settings in In /etc/imapd.conf: sasl_mech_list: PLAIN LOGIN sasl_pwcheck_method: saslauthd ## sasl_auxprop_plugin: sasldb sasl_auto_transition: no and my sasl config: [root@testserv ~]# cat /etc/sysconfig/saslauthd # Directory in which to place saslauthd's listening socket, pid file, and so # on. This directory must already exist. SOCKETDIR=/var/run/saslauthd # Mechanism to use when checking passwords. Run "saslauthd -v" to get a list # of which mechanism your installation was compiled with the ablity to use. MECH=pam # Additional flags to pass to saslauthd on the command line. See saslauthd(8) # for the list of accepted flags. FLAGS="-c -r -O /etc/saslauthd.conf" [root@testserv ~]# cat /etc/saslauthd.conf ldap_servers: ldap://127.0.0.1/ ldap_search_base: dc=%d,o=mydomain,c=com ldap_auth_method: bind #ldap_filter: (|(uid=%u)((&(mail=%u@%d)(accountStatus=active))) ldap_filter: (&(mail=%u@%d)(accountStatus=active)) ldap_debug: 1 ldap_version: 3 The accountStatus=active is not in ldap yet, but that doesn't make a difference since I don't see it in the filter... that's not the reason for the failure. The weird thing is, I do get an error when I rename or remove /etc/saslauthd.conf, but when the file exists it seems happily ignored... The filter in slapd.log seems to be taken from /etc/ldap.conf. Apart from some timers, that only contains: host 127.0.0.1 base o=mydomain,c=com pam_login_attribute mail Outcommenting the pam_login_attribute results in this filter in slapd.log: filter="([email protected])" Pam-imap looks like this: [root@testserv ~]# cat /etc/pam.d/imap auth required pam_ldap.so debug account required pam_ldap.so debug #auth sufficient pam_unix.so likeauth nullok #auth sufficient pam_ldap.so use_first_pass #auth required pam_deny.so #account sufficient pam_unix.so #account sufficient pam_ldap.so The outcommented stuff is because I don't have the cyrus admin user in Ldap; that's a Linux user. That works fine when uncommented, but I still need to play around with that a little and first I wanna get imap working. Finally nsswitch: [root@testserv ~]# cat /etc/nsswitch.conf # # /etc/nsswitch.conf # # An example Name Service Switch config file. This file should be # sorted with the most-used services at the beginning. # # The entry '[NOTFOUND=return]' means that the search for an # entry should stop if the search in the previous entry turned # up nothing. Note that if the search failed due to some other reason # (like no NIS server responding) then the search continues with the # next entry. # # Legal entries are: # # nisplus or nis+ Use NIS+ (NIS version 3) # nis or yp Use NIS (NIS version 2), also called YP # dns Use DNS (Domain Name Service) # files Use the local files # db Use the local database (.db) files # compat Use NIS on compat mode # hesiod Use Hesiod for user lookups # [NOTFOUND=return] Stop searching if not found so far # # To use db, put the "db" in front of "files" for entries you want to be # looked up first in the databases # # Example: #passwd: db files nisplus nis #shadow: db files nisplus nis #group: db files nisplus nis passwd: compat ldap group: compat ldap shadow: compat ldap hosts: files dns bootparams: nisplus [NOTFOUND=return] files ethers: files netmasks: files networks: files protocols: files rpc: files services: files netgroup: nisplus publickey: nisplus automount: files nisplus aliases: files nisplus Any info where to start looking will be greatly appreciated! Thnx in advance

  Read the article

• How to convert html textfield/area data to server-side txt file? [closed]

  - by olijake

  How can I make a script that will convert the text/data in a html textfield/textarea and send it to the server, which then saves it as a .txt file for storage? NOTE: I am hosting a website(for testing purposes) using Apache 2.2 on a Windows 7 machine. I downloaded PHP version 5.4.7, but have not yet installed on my server yet (not sure if I will need it, but also not sure how to install it). 1st problem: Saving text to server Html page/section with title textfield, text textarea, and submit button. You would enter a title, the text/notes you need in the textfield, then press the submit button to have it store the text in the textarea, as a .txt file on the server called .txt. 2nd problem: Opening text from server Html with list of all txt files OR textfield for entering in title, then submit button to send the title of the requested .txt file to the server, which would then load it up on the page. Here is what I have so far: (let me know if there is something that I should change or if something just isn't correct in the index.html code I have right now.) <!DOCTYPE HTML> <html> <head> <title>Insert Title</title> <meta http-equiv="Content-Type" content="Text/HTML; charset=UTF-8"/> </head> <body> <form method="post" action="save.INSERT_FILETYPE" name="textfile" enctype="multipart/form-data"> <input type="text" name="title"><br/> <textarea rows="20" cols="100" id="text" name="text"></textarea><br/> <input type="submit" name="submit" value="Submit Text to Server"> </form><br/> <hr style="width: 100%; height: 4px;"><br/> <form method="post" action="open.INSERT_FILETYPE" name="textfile" enctype="multipart/form-data"> <input type="text" name="title"><br/> <input type="submit" name="submit" value="Submit Txt File Request"> </form><br/> <div>Opened text file displays here or goes on another page</div> </body> </html> I plan on using a server side language/script, but ANYTHING that gets the job done is fine. I already tried looking into using some ASP/jScript/PHP, but have had some trouble implementing it into my server. (ie: getting the modules loaded and telling the server what file types to parse.) I know this may be an extremely easy fix, but then in that case, hopefully you wouldn't mind helping me out a little :). If it turns out that this is MUCH more complicated than I expect, then feel free to let me know that, so I don't waste me time running in circles. I appreciate any help/assistance that you can provide, Thanks, Jake EDIT: Wrong Apache version. In response to the comments/closing of this thread: My question: "How exactly do I install the PHP module on the apache server? and is this even possible? and is this even recommended?" ^ In case I wasn't clear enough already To Clarify: I understand the basics of PHP, I just have trouble with INSTALLING PHP on the apache server. (I have used PHP before, but never successfully on apache (so far...)) For my script I wrote something similar to this already (using fopen() and a few other commands): <?php fopen("notes.txt", "r"); file_put_contents("notes.txt",teststring1); ?> I have used javascript for this task before also (although I prefer using PHP and server-side languages): <script language="javascript"> function WriteToFile(){ var fso = new ActiveXObject("Scripting.FileSystemObject"); var s = fso.CreateTextFile("C:\\NewFile.txt", true); var text=document.getElementById("TextArea1").innerText; s.WriteLine(text); s.WriteLine('***********************'); s.Close(); } </script>

  Read the article

• Does an ESEUTIL defrag of an Exchange store also perform an integrity check/repair on it?

  - by Bigbio2002

  Earlier this morning, store.exe fuzzled up in one way or another, which necessitated a restart of our Exchange server. It came back online with no errors or problems, all the transaction logs replayed successfully, and all the stores mounted as normal. To me, it was just one of those random crashes; however, our consultant suspects it was caused by corruption in one of the stores. Perhaps he's correct, since he has far more experience than me, but that's not the point. To fix the suspected errors, he's planinng to run an ESEUTIL defrag (via PerfectDisk) to fix them, which he claims will also fix any errors present. From what I understand, defrag, verify, and repair are 3 separate actions, and a defrag does not imply any kind of integrity check. Is this correct? Are there any dangers of running a straight-up defrag on a database that might be corrupt? Edit: Here's the first error in the event log, which indicated the start of the problems we were having. Anyone know what it might indicate? Event Type: Error Event Source: Microsoft Exchange Server Event Category: None Event ID: 1000 Date: 11/23/2011 Time: 8:15:47 AM User: N/A Computer: SERVER Description: Faulting application exsp.dll, version 6.5.7638.1, stamp 430e735b, faulting module kernel32.dll, version 5.2.3790.4480, stamp 49c51f0a, debug? 0, fault address 0x0000bef7. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 41 00 70 00 70 00 6c 00 A.p.p.l. 0008: 69 00 63 00 61 00 74 00 i.c.a.t. 0010: 69 00 6f 00 6e 00 20 00 i.o.n. . 0018: 46 00 61 00 69 00 6c 00 F.a.i.l. 0020: 75 00 72 00 65 00 20 00 u.r.e. . 0028: 20 00 65 00 78 00 73 00 .e.x.s. 0030: 70 00 2e 00 64 00 6c 00 p...d.l. 0038: 6c 00 20 00 36 00 2e 00 l. .6... 0040: 35 00 2e 00 37 00 36 00 5...7.6. 0048: 33 00 38 00 2e 00 31 00 3.8...1. 0050: 20 00 34 00 33 00 30 00 .4.3.0. 0058: 65 00 37 00 33 00 35 00 e.7.3.5. 0060: 62 00 20 00 69 00 6e 00 b. .i.n. 0068: 20 00 6b 00 65 00 72 00 .k.e.r. 0070: 6e 00 65 00 6c 00 33 00 n.e.l.3. 0078: 32 00 2e 00 64 00 6c 00 2...d.l. 0080: 6c 00 20 00 35 00 2e 00 l. .5... 0088: 32 00 2e 00 33 00 37 00 2...3.7. 0090: 39 00 30 00 2e 00 34 00 9.0...4. 0098: 34 00 38 00 30 00 20 00 4.8.0. . 00a0: 34 00 39 00 63 00 35 00 4.9.c.5. 00a8: 31 00 66 00 30 00 61 00 1.f.0.a. 00b0: 20 00 66 00 44 00 65 00 .f.D.e. 00b8: 62 00 75 00 67 00 20 00 b.u.g. . 00c0: 30 00 20 00 61 00 74 00 0. .a.t. 00c8: 20 00 6f 00 66 00 66 00 .o.f.f. 00d0: 73 00 65 00 74 00 20 00 s.e.t. . 00d8: 30 00 30 00 30 00 30 00 0.0.0.0. 00e0: 62 00 65 00 66 00 37 00 b.e.f.7. 00e8: 0d 00 0a 00 ....

  Read the article

• Varnish 3.0.2 to Apache2 sometimes return error 503

  - by Ronnie Jespersen

  Hey guys I hope you can help me out here. I have an Ngingx parsing http and https to a varnish cache(3.0.2). From the varnish it is sent to apache2. Now I have for some time been tracking some strange 503 errors. But I cant seem to find the silver bullet. Currently I am logging the 503 errors through varnish this way: sudo varnishlog -c -m TxStatus:503 >> /home/rj/varnishlog503.log and then referring to the apache access log to see if any 503 requests have been handled. Today I had a health check from the firewall that failed: 20 SessionOpen c 127.0.0.1 34319 :8081 20 ReqStart c 127.0.0.1 34319 607335635 20 RxRequest c HEAD 20 RxURL c /health-check 20 RxProtocol c HTTP/1.0 20 RxHeader c X-Real-IP: 192.168.3.254 20 RxHeader c Host: 192.168.3.189 20 RxHeader c X-Forwarded-For: 192.168.3.254 20 RxHeader c Connection: close 20 RxHeader c User-Agent: Astaro Service Monitor 0.9 20 RxHeader c Accept: */* 20 VCL_call c recv lookup 20 VCL_call c hash 20 Hash c /health-check 20 VCL_return c hash 20 VCL_call c miss fetch 20 Backend c 33 aurum aurum 20 FetchError c http first read error: -1 11 (No error recorded) 20 VCL_call c error deliver 20 VCL_call c deliver deliver 20 TxProtocol c HTTP/1.1 20 TxStatus c 503 20 TxResponse c Service Unavailable 20 TxHeader c Server: Varnish 20 TxHeader c Content-Type: text/html; charset=utf-8 20 TxHeader c Retry-After: 5 20 TxHeader c Content-Length: 879 20 TxHeader c Accept-Ranges: bytes 20 TxHeader c Date: Wed, 06 Jun 2012 12:35:12 GMT 20 TxHeader c X-Varnish: 607335635 20 TxHeader c Age: 60 20 TxHeader c Via: 1.1 varnish 20 TxHeader c Connection: close 20 Length c 879 20 ReqEnd c 607335635 1338986052.649786949 1338986112.648169994 0.000160217 59.997980356 0.000402689 Now the backend server (apache) does not have any 503 error in the access log at this point. So I am confused. Is this varnish throwing a 503 because it thinks apache is to slow? There is a lot traffic coming through at this point so I know the server is up and running. I do have other 503 error codes with posts and gets so there is really no pattern. It seems to be at random times and random requests. Even in the morning when the server dosen't seem to be doing anything. I do see another pattern in the log: 4 VCL_call c recv pass 4 VCL_call c hash 4 Hash c /?id=412 4 VCL_return c hash 4 VCL_call c pass pass 4 FetchError c no backend connection 4 VCL_call c error deliver 4 VCL_call c deliver deliver Here fetcherror says "no backend connection". A summery of the FetchErrors in todays log: 16 FetchError c http first read error: -1 11 (No error recorded) 5 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 19 FetchError c http first read error: -1 11 (No error recorded) 5 FetchError c http first read error: -1 11 (No error recorded) 23 FetchError c http first read error: -1 11 (No error recorded) 24 FetchError c http first read error: -1 11 (No error recorded) 16 FetchError c http first read error: -1 11 (No error recorded) 6 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 5 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 22 FetchError c http first read error: -1 11 (No error recorded) 6 FetchError c http first read error: -1 11 (No error recorded) 21 FetchError c http first read error: -1 11 (No error recorded) 26 FetchError c no backend connection 4 FetchError c no backend connection 20 FetchError c http first read error: -1 11 (No error recorded) 39 FetchError c http first read error: -1 11 (No error recorded) I haven't changed the default timeout values for varnish. This is my configuration for one of the backend servers. backend xenon { .host = "192.168.3.187"; .port = "80"; .probe = { .url = "/health-check/"; .interval = 3s; .window = 5; .threshold = 2; } } I'm running prefork module on apache2 with this configuration <IfModule mpm_prefork_module> StartServers 1 MinSpareServers 2 MaxSpareServers 5 MaxClients 200 MaxRequestsPerChild 75 </IfModule> and only PHP files is sent to the server. Every other static file is handled by Nginx. Any ideas? ------- EDIT -------------- Some more debuging information I have run a varnishadm debug.health Backend radon is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.002560 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy Backend xenon is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.002760 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy Backend iridium is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.000849 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy Backend aurum is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.002100 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy And I have been monitoring varnishstat from the two load balancers 3224774 3.99 2.61 backend_conn - Backend conn. success 27 0.00 0.00 backend_unhealthy - Backend conn. not attempted 63 0.00 0.00 backend_fail - Backend conn. failures 358798 0.00 0.29 backend_reuse - Backend conn. reuses 21035 0.00 0.02 backend_toolate - Backend conn. was closed 379834 0.00 0.31 backend_recycle - Backend conn. recycles 26 0.00 0.00 backend_retry - Backend conn. retry 3217751 5.99 2.61 backend_conn - Backend conn. success 32 0.00 0.00 backend_fail - Backend conn. failures 364185 0.00 0.30 backend_reuse - Backend conn. reuses 27077 0.00 0.02 backend_toolate - Backend conn. was closed 391263 0.00 0.32 backend_recycle - Backend conn. recycles 36 0.00 0.00 backend_retry - Backend conn. retry Notice that none of them have reported backend_fail. /Ronnie

  Read the article

• Print driver installs failing

  - by Kasius

  All of the Windows 7 64-bit Enterprise machines in my organization are failing to install a good number of printer drivers that previously installed without issue. This only happens with printer drivers. And not with all printer drivers. Just some. Network drivers, video drivers, etc. have had no problems. Here is part of setupapi.dev.log for a Dymo LabelWriter printer driver that is failing to install: dvi: {Plug and Play Service: Device Install for USBPRINT\DYMOLABELWRITER_450_TURBO\6&538F51D&0&USB001} ump: Creating Install Process: DrvInst.exe 09:36:58.071 ndv: Infpath=C:\Windows\INF\oem0.inf ndv: DriverNodeName=dymo.inf:DYMO.NTamd64.6.0:LW_450_TURBO_VISTA:8.1.0.363:usbprint\dymolabelwriter_450_aa08 ndv: DriverStorepath=C:\Windows\System32\DriverStore\FileRepository\dymo.inf_amd64_neutral_3a631b118b7a5828\dymo.inf ndv: Building driver list from driver node strong name... dvi: Searching for hardware ID(s): dvi: usbprint\dymolabelwriter_450_aa08 dvi: dymolabelwriter_450_aa08 inf: Opened PNF: 'C:\Windows\System32\DriverStore\FileRepository\dymo.inf_amd64_neutral_3a631b118b7a5828\dymo.inf' ([strings]) dvi: Selected driver installs from section [LW_450_TURBO_VISTA] in 'c:\windows\system32\driverstore\filerepository\dymo.inf_amd64_neutral_3a631b118b7a5828\dymo.inf'. dvi: Class GUID of device changed to: {4d36e979-e325-11ce-bfc1-08002be10318}. dvi: Set selected driver complete. ndv: {Core Device Install} 09:36:58.133 inf: Opened INF: 'C:\Windows\INF\oem0.inf' ([strings]) inf: Saved PNF: 'C:\Windows\INF\oem0.PNF' (Language = 0409) dvi: {DIF_ALLOW_INSTALL} 09:36:58.164 dvi: Using exported function 'ClassInstall32' in module 'C:\Windows\system32\ntprint.dll'. dvi: Class installer == ntprint.dll,ClassInstall32 dvi: No CoInstallers found dvi: Class installer: Enter 09:36:58.164 dvi: Class installer: Exit dvi: Default installer: Enter 09:36:58.180 dvi: Default installer: Exit dvi: {DIF_ALLOW_INSTALL - exit(0xe000020e)} 09:36:58.180 ndv: Installing files... dvi: {DIF_INSTALLDEVICEFILES} 09:36:58.180 dvi: Class installer: Enter 09:36:58.180 inf: Opened INF: 'C:\Windows\System32\DriverStore\FileRepository\dymo.inf_amd64_neutral_3a631b118b7a5828\dymo.inf' ([strings]) inf: Opened INF: 'C:\Windows\System32\DriverStore\FileRepository\dymo.inf_amd64_neutral_3a631b118b7a5828\dymo.inf' ([strings]) !!! dvi: Class installer: failed(0x00000490)! !!! dvi: Error 1168: Element not found. dvi: {DIF_INSTALLDEVICEFILES - exit(0x00000490)} 09:37:22.063 ndv: Device install status=0x00000490 ndv: Performing device install final cleanup... ! ndv: Queueing up error report since device installation failed... ndv: {Core Device Install - exit(0x00000490)} 09:37:22.063 dvi: {DIF_DESTROYPRIVATEDATA} 09:37:22.063 dvi: Class installer: Enter 09:37:22.063 dvi: Class installer: Exit dvi: Default installer: Enter 09:37:22.063 dvi: Default installer: Exit dvi: {DIF_DESTROYPRIVATEDATA - exit(0xe000020e)} 09:37:22.063 ump: Server install process exited with code 0x00000490 09:37:22.063 ump: {Plug and Play Service: Device Install exit(00000490)} Notice these lines in particular: !!! dvi: Class installer: failed(0x00000490)! !!! dvi: Error 1168: Element not found. dvi: {DIF_INSTALLDEVICEFILES - exit(0x00000490)} 09:37:22.063 ndv: Device install status=0x00000490 From what I have read, the "Element not found" error should be accompanied by an event describing what element was not found. The error that appears in Device Manager is "The driver cannot be installed because it is either not digitally signed or not signed in the appropriate manner." It appears to be signed fine though. It has an accompanying .CAT file and worked previously. And when installing, the following messages are logged in setupapi.dev.log: sto: {DRIVERSTORE_IMPORT_NOTIFY_VALIDATE} 09:36:56.277 inf: Opened INF: 'C:\Windows\System32\DriverStore\Temp\{272e2305-961c-7942-9ede-966f01047043}\dymo.inf' ([strings]) sig: {_VERIFY_FILE_SIGNATURE} 09:36:56.292 sig: Key = dymo.inf sig: FilePath = C:\Windows\System32\DriverStore\Temp\{272e2305-961c-7942-9ede-966f01047043}\dymo.inf sig: Catalog = C:\Windows\System32\DriverStore\Temp\{272e2305-961c-7942-9ede-966f01047043}\DYMO.CAT sig: Success: File is signed in catalog. sig: {_VERIFY_FILE_SIGNATURE exit(0x00000000)} 09:36:56.355 sto: Validating driver package files against catalog 'DYMO.CAT'. sto: Driver package is valid. sto: {DRIVERSTORE_IMPORT_NOTIFY_VALIDATE exit(0x00000000)} 09:36:56.402 sto: Verified driver package signature: sto: Digital Signer Score = 0x0D000005 sto: Digital Signer Name = Microsoft Windows Hardware Compatibility Publisher Now here's where it gets strange. If I take it off the domain, it installs fine. But it doesn't seem to have anything to do with Group Policy. I moved the machine to an OU that blocks inheritance, ran a gpupdate, ran rsop.msc to verify, and tried again. And it still didn't work. Likewise, I removed a machine from the domain, manually set all of the domain Group Policy settings in gpedit.msc, and tried that way, and it worked fine. So it seems like the Group Policy settings are irrelevant. What other domain-related issue could be causing this though? Any ideas on what to try next would be greatly appreciated. I'm not sure where to go from here. Thanks!

  Read the article

• Apache2 Segfault - need help interpreting this coredump (suspect cause is memcache / php session related)

  - by WayneDV

  Three Apache2 web servers running a PHP 5.2.3 web site. We're using Memcache to cache rendered pages but also as the storage engine of the PHP Sessions. At peak traffic times we're getting Apache segmentation faults on all three web servers and all HTTPD child processes segfault. My gut tells me that the increased Memcache traffic is stopping PHP sessions from being created or cleaned up and thus the processes die. Is it possible for someone to confirm that from the following? : #0 _zend_mm_free_int (heap=0x7fb67a075820, p=0x7fb67a011538) at /usr/src/debug/php-5.3.3/Zend/zend_alloc.c:2018 #1 0x00007fb665d02e82 in mmc_buffer_free (request=0x7fb67a011548) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_pool.c:50 #2 mmc_request_free (request=0x7fb67a011548) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_pool.c:169 #3 0x00007fb665d031ea in mmc_pool_free (pool=0x7fb67a00e458) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_pool.c:917 #4 0x00007fb665d0a2f1 in ps_close_memcache (mod_data=0x7fb66d625440) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_session.c:185 #5 0x00007fb66d1b0935 in php_session_save_current_state () at /usr/src/debug/php-5.3.3/ext/session/session.c:625 #6 php_session_flush () at /usr/src/debug/php-5.3.3/ext/session/session.c:1517 #7 0x00007fb66d1b0c1b in zm_deactivate_session (type=<value optimized out>, module_number=<value optimized out>) at /usr/src/debug/php-5.3.3/ext/session/session.c:2171 #8 0x00007fb66d2a719c in module_registry_cleanup (module=<value optimized out>) at /usr/src/debug/php-5.3.3/Zend/zend_API.c:2150 #9 0x00007fb66d2b1994 in zend_hash_reverse_apply (ht=0x7fb66d629d60, apply_func=0x7fb66d2a7180 <module_registry_cleanup>) at /usr/src/debug/php-5.3.3/Zend/zend_hash.c:755 #10 0x00007fb66d2a5c0d in zend_deactivate_modules () at /usr/src/debug/php-5.3.3/Zend/zend.c:866 #11 0x00007fb66d2541b5 in php_request_shutdown (dummy=<value optimized out>) at /usr/src/debug/php-5.3.3/main/main.c:1607 #12 0x00007fb66d32e037 in php_apache_request_dtor (r=0x7fb67a229658) at /usr/src/debug/php-5.3.3/sapi/apache2handler/sapi_apache2.c:509 #13 php_handler (r=0x7fb67a229658) at /usr/src/debug/php-5.3.3/sapi/apache2handler/sapi_apache2.c:681 #14 0x00007fb6784166f0 in ap_run_handler (r=0x7fb67a229658) at /usr/src/debug/httpd-2.2.15/server/config.c:158 #15 0x00007fb678419f58 in ap_invoke_handler (r=0x7fb67a229658) at /usr/src/debug/httpd-2.2.15/server/config.c:372 #16 0x00007fb6784254f0 in ap_process_request (r=0x7fb67a229658) at /usr/src/debug/httpd-2.2.15/modules/http/http_request.c:282 #17 0x00007fb678422418 in ap_process_http_connection (c=0x7fb67a2193a8) at /usr/src/debug/httpd-2.2.15/modules/http/http_core.c:190 #18 0x00007fb67841e1b8 in ap_run_process_connection (c=0x7fb67a2193a8) at /usr/src/debug/httpd-2.2.15/server/connection.c:43 #19 0x00007fb678429f4b in child_main (child_num_arg=<value optimized out>) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:662 #20 0x00007fb67842a21a in make_child (s=0x7fb679cd7860, slot=153) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:758 #21 0x00007fb67842aea4 in perform_idle_server_maintenance (_pconf=<value optimized out>, plog=<value optimized out>, s=<value optimized out>) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:893 #22 ap_mpm_run (_pconf=<value optimized out>, plog=<value optimized out>, s=<value optimized out>) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:1097 #23 0x00007fb678402890 in main (argc=1, argv=0x7fff6fecacb8) at /usr/src/debug/httpd-2.2.15/server/main.c:740 PHP.INI Follows: [PHP] engine = On short_open_tag = On asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL & ~E_DEPRECATED display_errors = Off display_startup_errors = Off log_errors = Off log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = Off html_errors = Off variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off file_uploads = On upload_max_filesize = 2M allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 sendmail_path = /usr/sbin/sendmail -t -i mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [MySQL] mysql.allow_persistent = On mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_links = -1 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.save_path = "/var/lib/php/session" session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 1 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.entropy_file = session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 /etc/php.d/memcached.ini : session.save_path="tcp://memcache1:11211?persistent=1&weight=1&timeout=3&retry_interval=15"

  Read the article

• Xen DomU on DRBD device: barrier errors

  - by Halfgaar

  I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

  Read the article

• KB2667402 update fails to install with 0x80004005. Yet it's also showing as installed

  - by growse

  I've got 15 Windows 2008 R2 x64 servers that I manage with SCCM2012. I've noticed during my Windows updates reporting that there's two boxes that are showing as 'error' for total updates installed. Digging around, it looks like the update that is failing to install is KB2667402. The Software Centre on the server itself shows the following: The software change returned error code 0x80004005(-2147467259). So SCCM thinks it hasn't installed the update. However, if I go to the Programs and Features application and select 'Windows Updates', I can see an entry for KB2667402: If I try and uninstall this, I get an error: An error occurred. Not all of the updates were successfully uninstalled If I try and download the patch from Microsoft directly, I get the same error installing as displayed in Software Centre. The only odd thing about this setup that I can think would affect this is that I run the RDP service on a non-standard port. However, I do this across all the servers, so it seems odd that it would fail on just 2 out of 15. The tail of the WindowsUpdate.log file is below: 2012-06-26 15:33:53:184 3924 1608 COMAPI ------------- 2012-06-26 15:33:53:190 3924 1608 COMAPI -- START -- COMAPI: Install [ClientId = CcmExec] 2012-06-26 15:33:53:190 3924 1608 COMAPI --------- 2012-06-26 15:33:53:190 3924 1608 COMAPI - Allow source prompts: No; Forced: No; Force quiet: Yes 2012-06-26 15:33:53:190 3924 1608 COMAPI - Updates in request: 1 2012-06-26 15:33:53:190 3924 1608 COMAPI - ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed 2012-06-26 15:33:53:199 860 1198 Agent ************* 2012-06-26 15:33:53:199 860 1198 Agent ** START ** Agent: Installing updates [CallerId = CcmExec] 2012-06-26 15:33:53:199 860 1198 Agent ********* 2012-06-26 15:33:53:199 860 1198 Agent * Updates to install = 1 2012-06-26 15:33:53:201 860 1198 Agent * Title = Security Update for Windows Server 2008 R2 x64 Edition (KB2667402) 2012-06-26 15:33:53:201 860 1198 Agent * UpdateId = {48859BE4-1331-4CD2-8E70-3B537180A0D0}.103 2012-06-26 15:33:53:201 860 1198 Agent * Bundles 1 updates: 2012-06-26 15:33:53:201 860 1198 Agent * {D854ECF1-99A7-4D67-B435-2D041BF79565}.103 2012-06-26 15:33:53:204 3924 1608 COMAPI - Updates to install = 1 2012-06-26 15:33:53:204 3924 1608 COMAPI <<-- SUBMITTED -- COMAPI: Install [ClientId = CcmExec] 2012-06-26 15:33:53:221 860 1198 Agent WARNING: failed to calculate prior restore point time with error 0x80070002; setting restore point 2012-06-26 15:33:53:222 860 1198 Agent WARNING: LoadLibrary failed for srclient.dll with hr:8007007e 2012-06-26 15:33:53:322 860 1198 DnldMgr Preparing update for install, updateId = {D854ECF1-99A7-4D67-B435-2D041BF79565}.103. 2012-06-26 15:33:53:325 5700 117c Misc =========== Logging initialized (build: 7.5.7601.17514, tz: +0100) =========== 2012-06-26 15:33:53:325 5700 117c Misc = Process: C:\Windows\system32\wuauclt.exe 2012-06-26 15:33:53:325 5700 117c Misc = Module: C:\Windows\system32\wuaueng.dll 2012-06-26 15:33:53:324 5700 117c Handler ::::::::::::: 2012-06-26 15:33:53:325 5700 117c Handler :: START :: Handler: CBS Install 2012-06-26 15:33:53:325 5700 117c Handler ::::::::: 2012-06-26 15:33:53:330 5700 117c Handler Starting install of CBS update D854ECF1-99A7-4D67-B435-2D041BF79565 2012-06-26 15:33:53:342 5700 117c Handler CBS package identity: Package_for_KB2667402~31bf3856ad364e35~amd64~~6.1.2.0 2012-06-26 15:33:53:366 5700 117c Handler Installing self-contained with source=C:\Windows\SoftwareDistribution\Download\44059e0415033d6f699a50ef69dd5ff2\windows6.1-kb2667402-v2-x64.cab, workingdir=C:\Windows\SoftwareDistribution\Download\44059e0415033d6f699a50ef69dd5ff2\inst 2012-06-26 15:33:56:270 5700 3b8 Handler FATAL: CBS called Error with 0x80004005, 2012-06-26 15:33:56:402 5700 117c Handler FATAL: Completed install of CBS update with type=0, requiresReboot=0, installerError=1, hr=0x80004005 2012-06-26 15:33:56:405 5700 117c Handler ::::::::: 2012-06-26 15:33:56:406 5700 117c Handler :: END :: Handler: CBS Install 2012-06-26 15:33:56:406 5700 117c Handler ::::::::::::: 2012-06-26 15:33:56:433 860 1198 Agent ********* 2012-06-26 15:33:56:433 860 1198 Agent ** END ** Agent: Installing updates [CallerId = CcmExec] 2012-06-26 15:33:56:433 860 1198 Agent ************* 2012-06-26 15:33:56:433 860 d14 AU Can not perform non-interactive scan if AU is interactive-only 2012-06-26 15:33:56:450 3924 e40 COMAPI >>-- RESUMED -- COMAPI: Install [ClientId = CcmExec] 2012-06-26 15:33:56:450 3924 e40 COMAPI - Install call complete (succeeded = 0, succeeded with errors = 0, failed = 1, unaccounted = 0) 2012-06-26 15:33:56:450 3924 e40 COMAPI - Reboot required = No 2012-06-26 15:33:56:450 3924 e40 COMAPI - WARNING: Exit code = 0x00000000; Call error code = 0x80240022 2012-06-26 15:33:56:451 3924 e40 COMAPI --------- 2012-06-26 15:33:56:451 3924 e40 COMAPI -- END -- COMAPI: Install [ClientId = CcmExec] 2012-06-26 15:33:56:451 3924 e40 COMAPI ------------- 2012-06-26 15:33:56:536 860 13a4 AU Triggering Offline detection (non-interactive) 2012-06-26 15:33:56:536 860 d14 AU ############# 2012-06-26 15:33:56:536 860 d14 AU ## START ## AU: Search for updates 2012-06-26 15:33:56:536 860 d14 AU ######### 2012-06-26 15:33:56:539 860 d14 AU <<## SUBMITTED ## AU: Search for updates [CallId = {2DBB046C-2265-421B-A37B-93BDECC6C261}] 2012-06-26 15:33:56:539 860 1788 Agent ************* 2012-06-26 15:33:56:539 860 1788 Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates] 2012-06-26 15:33:56:539 860 1788 Agent ********* 2012-06-26 15:33:56:539 860 1788 Agent * Online = No; Ignore download priority = No 2012-06-26 15:33:56:539 860 1788 Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1" 2012-06-26 15:33:56:539 860 1788 Agent * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed 2012-06-26 15:33:56:539 860 1788 Agent * Search Scope = {Machine} 2012-06-26 15:33:58:562 860 1788 Agent * Found 0 updates and 70 categories in search; evaluated appl. rules of 180 out of 1072 deployed entities 2012-06-26 15:33:58:565 860 1788 Agent ********* 2012-06-26 15:33:58:565 860 1788 Agent ** END ** Agent: Finding updates [CallerId = AutomaticUpdates] 2012-06-26 15:33:58:565 860 1788 Agent ************* 2012-06-26 15:33:58:650 860 f2c AU >>## RESUMED ## AU: Search for updates [CallId = {2DBB046C-2265-421B-A37B-93BDECC6C261}] 2012-06-26 15:33:58:650 860 f2c AU # 0 updates detected 2012-06-26 15:33:58:650 860 f2c AU ######### 2012-06-26 15:33:58:650 860 f2c AU ## END ## AU: Search for updates [CallId = {2DBB046C-2265-421B-A37B-93BDECC6C261}] 2012-06-26 15:33:58:650 860 f2c AU ############# 2012-06-26 15:33:58:650 860 f2c AU Featured notifications is disabled. 2012-06-26 15:33:58:651 860 f2c AU Successfully wrote event for AU health state:0 2012-06-26 15:33:58:652 860 f2c AU Successfully wrote event for AU health state:0

  Read the article

• CentOS - Configuring Puppet to play nice with SELinux

  - by Mike Purcell

  I am running into an issue every time I attempt to start the puppetmasterd service, for which I receive the following error message: root@service1 ~ # -> /etc/init.d/puppetmaster start Starting puppetmaster: Could not prepare for execution: Got 1 failure(s) while initializing: change from absent to directory failed: Could not set 'directory on ensure: Permission denied - /etc/puppet/ssl [FAILED] Apparently there was a known issue with this scenario as outlined in this bug report, however in the bug report it states the issue has been resolved in selinux-policy-3.9.16-29.fc15, but the latest CentOS default upstream version is 3.7.19-155.el6_3.4. So I am trying to figure out the best solution. I can either create a local security policy to allow puppetmasterd the access it needs, or keep researching and install a newer version of selinux-policy outside of the default upstream channel. Anyone have any recommendations? Please don't recommend disabling SELinux... ----- Update ----- Here is the puppet.conf: [main] # The Puppet log directory. # The default value is '$vardir/log'. logdir = /var/log/puppet # Where Puppet PID files are kept. # The default value is '$vardir/run'. rundir = /var/run/puppet # Where SSL certificates are kept. # The default value is '$confdir/ssl'. ssldir = $vardir/ssl [master] certname=puppetmaster.ownij.lan dns_alt_names=puppetmaster.ownij.lan [agent] # The file in which puppetd stores a list of the classes # associated with the retrieved configuratiion. Can be loaded in # the separate ``puppet`` executable using the ``--loadclasses`` # option. # The default value is '$confdir/classes.txt'. classfile = $vardir/classes.txt # Where puppetd caches the local configuration. An # extension indicating the cache format is added automatically. # The default value is '$confdir/localconfig'. localconfig = $vardir/localconfig server=puppetmaster.ownij.lan And here are the denials per the audit log: type=AVC msg=audit(1349751364.985:666): avc: denied { search } for pid=15093 comm="puppetmasterd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:puppetmaster_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349751364.985:666): arch=c000003e syscall=4 success=no exit=-13 a0=1391420 a1=7fffef09ed10 a2=7fffef09ed10 a3=120c500 items=0 ppid=15092 pid=15093 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=pts1 ses=13 comm="puppetmasterd" exe="/usr/bin/ruby" subj=unconfined_u:system_r:puppetmaster_t:s0 key=(null) type=AVC msg=audit(1349751365.302:667): avc: denied { search } for pid=15093 comm="puppetmasterd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:puppetmaster_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349751365.302:667): arch=c000003e syscall=4 success=no exit=-13 a0=1d18530 a1=7fffef0d04d0 a2=7fffef0d04d0 a3=8 items=0 ppid=15092 pid=15093 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=pts1 ses=13 comm="puppetmasterd" exe="/usr/bin/ruby" subj=unconfined_u:system_r:puppetmaster_t:s0 key=(null) type=AVC msg=audit(1349751365.465:668): avc: denied { search } for pid=15093 comm="puppetmasterd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:puppetmaster_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349751365.465:668): arch=c000003e syscall=4 success=no exit=-13 a0=1af3930 a1=7fffef0c5c70 a2=7fffef0c5c70 a3=8 items=0 ppid=15092 pid=15093 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=pts1 ses=13 comm="puppetmasterd" exe="/usr/bin/ruby" subj=unconfined_u:system_r:puppetmaster_t:s0 key=(null) type=AVC msg=audit(1349751365.467:669): avc: denied { search } for pid=15093 comm="puppetmasterd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:puppetmaster_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349751365.467:669): arch=c000003e syscall=4 success=no exit=-13 a0=1b17aa0 a1=7fffef0c5c70 a2=7fffef0c5c70 a3=8 items=0 ppid=15092 pid=15093 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=pts1 ses=13 comm="puppetmasterd" exe="/usr/bin/ruby" subj=unconfined_u:system_r:puppetmaster_t:s0 key=(null) type=AVC msg=audit(1349751366.401:670): avc: denied { write } for pid=15093 comm="puppetmasterd" name="puppet" dev=dm-0 ino=132035 scontext=unconfined_u:system_r:puppetmaster_t:s0 tcontext=system_u:object_r:puppet_etc_t:s0 tclass=dir type=SYSCALL msg=audit(1349751366.401:670): arch=c000003e syscall=83 success=no exit=-13 a0=2d7a400 a1=1f9 a2=2d7a40f a3=7fffef0a6df0 items=0 ppid=15092 pid=15093 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=pts1 ses=13 comm="puppetmasterd" exe="/usr/bin/ruby" subj=unconfined_u:system_r:puppetmaster_t:s0 key=(null) And the audit log if I pass through audit2allow: root@service1 ~ # -> fgrep puppetmasterd /var/log/audit/audit.log | audit2allow -m puppetmasterd module puppetmasterd 1.0; require { type home_root_t; type puppetmaster_t; type puppet_etc_t; type puppet_var_run_t; type httpd_sys_content_t; class lnk_file { relabelfrom relabelto }; class file { relabelfrom read getattr open }; class dir { write read search getattr setattr }; } #============= puppetmaster_t ============== allow puppetmaster_t home_root_t:dir { search getattr }; allow puppetmaster_t httpd_sys_content_t:dir read; allow puppetmaster_t httpd_sys_content_t:file { read getattr open }; #!!!! The source type 'puppetmaster_t' can write to a 'dir' of the following types: # puppet_log_t, puppet_var_lib_t, puppet_var_run_t, puppetmaster_tmp_t allow puppetmaster_t puppet_etc_t:dir { write setattr }; allow puppetmaster_t puppet_etc_t:lnk_file { relabelfrom relabelto }; allow puppetmaster_t puppet_var_run_t:file relabelfrom;

  Read the article

• Sporadic unspecific kernel panic

  - by koma

  I'm experiencing seldom (so far about once a month) hard crashes on our ubuntu server 10.04 LTS box. The box itself is quite old (Dell PowerEdge 750 from 2004, Pentium4 2.8 GHz). I set up netconsole after it crashed twice last thursday and was able to extract the following output: [ 9354.062473] invalid opcode: 0000 [#1] SMP [ 9354.062516] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/uevent [ 9354.062555] Modules linked in: ppdev adm1026 hwmon_vid i2c_i801 bridge stp dcdbas psmouse serio_raw netconsole configfs shpchp lp parport usbhid hid e1000 [ 9354.062685] [ 9354.062704] Pid: 3988, comm: rsync Not tainted 2.6.38-12-generic-pae #51~lucid1-Ubuntu Dell Computer Corporation PowerEdge 750 /0R1479 [ 9354.062773] EIP: 0060:[<c104fef1>] EFLAGS: 00010046 CPU: 1 [ 9354.062802] EIP is at check_preempt_wakeup+0x181/0x250 [ 9354.062826] EAX: 00000002 EBX: f2a10ccc ECX: 00000000 EDX: 00000002 [ 9354.062850] ESI: f1db71cc EDI: f1db71a0 EBP: f1dbdea8 ESP: f1dbde8c [ 9354.062875] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 9354.062900] Process rsync (pid: 3988, ti=f1dbc000 task=f1db71a0 task.ti=f1dbc000) [ 9354.062933] Stack: [ 9354.062951] 0053ea60 f7907680 f28da840 f2a10ca0 c153ea60 f7907680 c153ea60 f1dbdebc [ 9354.063019] c103f98a f2a10ca0 f7907680 00000001 f1dbdef8 c104f97f 00000000 f2f0bacc [ 9354.063088] f7904338 00000001 00000003 00000000 f2f0bacc 00000001 00000001 00000086 [ 9354.063157] Call Trace: [ 9354.063183] [<c103f98a>] check_preempt_curr+0x6a/0x80 [ 9354.063210] [<c104f97f>] try_to_wake_up+0x5f/0x3f0 [ 9354.063236] [<c1077a00>] ? hrtimer_wakeup+0x0/0x30 [ 9354.063261] [<c104fd64>] wake_up_process+0x14/0x20 [ 9354.063286] [<c1077a1d>] hrtimer_wakeup+0x1d/0x30 [ 9354.063310] [<c1077f4a>] __run_hrtimer+0x7a/0x1c0 [ 9354.063336] [<c107dbad>] ? ktime_get+0x6d/0x110 [ 9354.063360] [<c1078310>] hrtimer_interrupt+0x120/0x2b0 [ 9354.063390] [<c1535c36>] smp_apic_timer_interrupt+0x56/0x8a [ 9354.063418] [<c152f459>] apic_timer_interrupt+0x31/0x38 [ 9354.063446] [<c1520000>] ? mca_attach_bus+0x5/0xc0 [ 9354.063469] Code: 8b 9b 20 01 00 00 8b 86 24 01 00 00 3b 83 24 01 00 00 75 e6 85 db 0f 84 a3 00 00 00 89 da 89 f0 e8 75 f6 fe ff 83 f8 01 0f 85 00 <fe> ff ff 89 f8 e8 95 f9 fe ff 8b 5e 1c 85 db 0f 84 e4 fe ff ff [ 9354.063804] EIP: [<c104fef1>] check_preempt_wakeup+0x181/0x250 SS:ESP 0068:f1dbde8c [ 9354.064231] ---[ end trace 290689cea65aea7f ]--- [ 9354.064290] Kernel panic - not syncing: Fatal exception in interrupt [ 9354.064352] Pid: 3988, comm: rsync Tainted: G D 2.6.38-12-generic-pae #51~lucid1-Ubuntu [ 9354.064424] Call Trace: [ 9354.064481] [<c152c057>] ? panic+0x5c/0x15b [ 9354.064539] [<c15302bd>] ? oops_end+0xcd/0xd0 [ 9354.064539] [<c100d9e4>] ? die+0x54/0x80 [ 9354.064539] [<c152f926>] ? do_trap+0x96/0xc0 [ 9354.064539] [<c100ba00>] ? do_invalid_op+0x0/0xa0 [ 9354.064539] [<c100ba8b>] ? do_invalid_op+0x8b/0xa0 [ 9354.064539] [<c104fef1>] ? check_preempt_wakeup+0x181/0x250 [ 9354.064539] [<c144884d>] ? __kfree_skb+0x3d/0x90 [ 9354.064539] [<c1042ae7>] ? update_curr+0x247/0x2a0 [ 9354.064539] [<c10447bb>] ? update_cfs_load+0x11b/0x2d0 [ 9354.064539] [<c1042a25>] ? update_curr+0x185/0x2a0 [ 9354.064539] [<c152f6bf>] ? error_code+0x67/0x6c [ 9354.064539] [<c104fef1>] ? check_preempt_wakeup+0x181/0x250 [ 9354.064539] [<c103f98a>] ? check_preempt_curr+0x6a/0x80 [ 9354.064539] [<c104f97f>] ? try_to_wake_up+0x5f/0x3f0 [ 9354.064539] [<c1077a00>] ? hrtimer_wakeup+0x0/0x30 [ 9354.064539] [<c104fd64>] ? wake_up_process+0x14/0x20 [ 9354.064539] [<c1077a1d>] ? hrtimer_wakeup+0x1d/0x30 [ 9354.064539] [<c1077f4a>] ? __run_hrtimer+0x7a/0x1c0 [ 9354.064539] [<c107dbad>] ? ktime_get+0x6d/0x110 [ 9354.064539] [<c1078310>] ? hrtimer_interrupt+0x120/0x2b0 [ 9354.064539] [<c1535c36>] ? smp_apic_timer_interrupt+0x56/0x8a [ 9354.064539] [<c152f459>] ? apic_timer_interrupt+0x31/0x38 [ 9354.064539] [<c1520000>] ? mca_attach_bus+0x5/0xc0 Googling for this issue didn't really turn up anything useful (most stuff I found was related to btrfs, but I don't use that, although the module exists and is sometimes loaded). From experience it might have to do with relatively heavy I/O, as two of the panics happened during a backup procedure. Kernel is 2.6.38-12-generic-pae, but I'm pretty sure I also saw panics on 2.6.32. I meanwhile upgraded to 3.0.0-17-generic-pae and am waiting for the next crash ;-) I'm at a loss here, so any pointers where to look for the cause or what it could be would be great :-) Thanks !

  Read the article

• Multiple Graphics Cards on Fedora 15 (Gnome 3)

  - by Michael

  I have the (delightful) misfortune of having 3 graphics cards. They are XFX Radeon 5750s. Each drives 2 monitors via dvi. I am having a really hard time getting these running on fedora 15 (gnome 3). So my setup is 3 columns of 2 monitors (the upper monitor is mounted upside down in each column to reduce the bezel between monitors). When the (graphical) login screen comes up all 6 have the blue stripey background that must be the default, but then when I login, things get interesting. In the xorg.conf below, you will see only 2 of the screens in the serverlayout while the other 4 are commented out. Logging in with only 2 of the screens active works well (and it even remembers that the top one is upside down, and should be considered above the lower, i am not sure where it stores this info, but i set it using the graphical "Displays" settings) However, as soon as I uncomment a third screen, or more, it gives me an error message when I login. It's one of those friendly, less helpful messages (Oh no! Something has gone wrong. A problem has occurred and the system can't recover. Please log out and try again). If i do not use an xorg.conf, then the "Displays" prefs pane shows only the two monitors on one of my graphics cards Thanks to anyone who can help me get going! (xorg.conf and then lspci below, and xorg log) xorg.conf Section "ServerLayout" Identifier "X.org Configured" Screen "Screen0" 0 0 Screen "Screen1" Below "Screen0" # Screen "Screen2" RightOf "Screen0" # Screen "Screen3" RightOf "Screen1" # Screen "Screen4" RightOf "Screen3" # Screen "Screen5" RightOf "Screen4" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "record" Load "dri" Load "dbe" Load "extmod" Load "dri2" Load "glx" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor3" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor4" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor5" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" BusID "PCI:4:0:0" EndSection Section "Device" Identifier "Card1" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Card2" Driver "radeon" BusID "PCI:6:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card0" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card1" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen3" Device "Card1" Monitor "Monitor3" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen4" Device "Card2" Monitor "Monitor4" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen5" Device "Card2" Monitor "Monitor5" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection lspci output follows [tgm@tgm ~]$ lspci 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 02:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:02.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 04:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 04:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 05:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 05:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 06:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 06:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) xorg log (posted to fpaste due to how long it is. thanks to marcusw for the request) http://www.fpaste.org/r5ww/ xorg log with all 6 monitors enabled in xorg.conf (they all turn on and have blue, but then one gets the aforementioned user-friendly error message). http://www.fpaste.org/X63H/

  Read the article

• Creating a multi-tenant application using PostgreSQL's schemas and Rails

  - by ramon.tayag

  Stuff I've already figured out I'm learning how to create a multi-tenant application in Rails that serves data from different schemas based on what domain or subdomain is used to view the application. I already have a few concerns answered: How can you get subdomain-fu to work with domains as well? Here's someone that asked the same question which leads you to this blog. What database, and how will it be structured? Here's an excellent talk by Guy Naor, and good question about PostgreSQL and schemas. I already know my schemas will all have the same structure. They will differ in the data they hold. So, how can you run migrations for all schemas? Here's an answer. Those three points cover a lot of the general stuff I need to know. However, in the next steps I seem to have many ways of implementing things. I'm hoping that there's a better, easier way. Finally, to my question When a new user signs up, I can easily create the schema. However, what would be the best and easiest way to load the structure that the rest of the schemas already have? Here are some questions/scenarios that might give you a better idea. Should I pass it on to a shell script that dumps the public schema into a temporary one, and imports it back to my main database (pretty much like what Guy Naor says in his video)? Here's a quick summary/script I got from the helpful #postgres on freenode. While this will probably work, I'm gonna have to do a lot of stuff outside of Rails, which makes me a bit uncomfortable.. which also brings me to the next question. Is there a way to do this straight from Ruby on Rails? Like create a PostgreSQL schema, then just load the Rails database schema (schema.rb - I know, it's confusing) into that PostgreSQL schema. Is there a gem/plugin that has these things already? Methods like "create_pg_schema_and_load_rails_schema(the_new_schema_name)". If there's none, I'll probably work at making one, but I'm doubtful about how well tested it'll be with all the moving parts (especially if I end up using a shell script to create and manage new PostgreSQL schemas). Thanks, and I hope that wasn't too long! UPDATE May 11, 2010 11:26 GMT+8 Since last night I've been able to get a method to work that creates a new schema and loads schema.rb into it. Not sure if what I'm doing is correct (seems to work fine, so far) but it's a step closer at least. If there's a better way please let me know. module SchemaUtils def self.add_schema_to_path(schema) conn = ActiveRecord::Base.connection conn.execute "SET search_path TO #{schema}, #{conn.schema_search_path}" end def self.reset_search_path conn = ActiveRecord::Base.connection conn.execute "SET search_path TO #{conn.schema_search_path}" end def self.create_and_migrate_schema(schema_name) conn = ActiveRecord::Base.connection schemas = conn.select_values("select * from pg_namespace where nspname != 'information_schema' AND nspname NOT LIKE 'pg%'") if schemas.include?(schema_name) tables = conn.tables Rails.logger.info "#{schema_name} exists already with these tables #{tables.inspect}" else Rails.logger.info "About to create #{schema_name}" conn.execute "create schema #{schema_name}" end # Save the old search path so we can set it back at the end of this method old_search_path = conn.schema_search_path # Tried to set the search path like in the methods above (from Guy Naor) # conn.execute "SET search_path TO #{schema_name}" # But the connection itself seems to remember the old search path. # If set this way, it works. conn.schema_search_path = schema_name # Directly from databases.rake. # In Rails 2.3.5 databases.rake can be found in railties/lib/tasks/databases.rake file = "#{Rails.root}/db/schema.rb" if File.exists?(file) Rails.logger.info "About to load the schema #{file}" load(file) else abort %{#{file} doesn't exist yet. It's possible that you just ran a migration!} end Rails.logger.info "About to set search path back to #{old_search_path}." conn.schema_search_path = old_search_path end end

  Read the article

• Python unicode Decode Error SUDs

  - by PylonsN00b

  OK so I have # -*- coding: utf-8 -*- at the top of my script and it worked for being able to pull data from the database that had funny chars(Ñ ,Õ,é,—,–,’,…) in it and store that data into variables...but I have run into other problems, see I pull my data, organize it, and then dump it into a variables like so: title = product[1] Where product[1] is from my database result set Then I load it up for Suds like so: array_of_inventory_item_submit = ca_client_inventory.factory.create('ArrayOfInventoryItemSubmit') for product in products: inventory_item_submit = ca_client_inventory.factory.create('InventoryItemSubmit') inventory_item_list = get_item_list(product) inventory_item_submit = [inventory_item_list] array_of_inventory_item_submit.InventoryItemSubmit.append(inventory_item_submit) #Call that service baby! ca_client_inventory.service.SynchInventoryItemList(accountID, array_of_inventory_item_submit) Where get_item_list sets product[1] to title and (including a whole bunch of other nodes): inventory_item_submit.Title = title So everything runs fine until I call ca_client_inventory.service.SynchInventoryItemList that contains array_of_inventory_item_submit which contains the title w/ the funky char...here is the error: Traceback (most recent call last): File "upload_all_inventory_ebay.py", line 421, in <module> ca_client_inventory.service.SynchInventoryItemList(accountID, array_of_inventory_item_submit) File "build/bdist.macosx-10.6-i386/egg/suds/client.py", line 539, in __call__ File "build/bdist.macosx-10.6-i386/egg/suds/client.py", line 592, in invoke File "build/bdist.macosx-10.6-i386/egg/suds/bindings/binding.py", line 118, in get_message File "build/bdist.macosx-10.6-i386/egg/suds/bindings/document.py", line 63, in bodycontent File "build/bdist.macosx-10.6-i386/egg/suds/bindings/document.py", line 105, in mkparam File "build/bdist.macosx-10.6-i386/egg/suds/bindings/binding.py", line 260, in mkparam File "build/bdist.macosx-10.6-i386/egg/suds/mx/core.py", line 62, in process File "build/bdist.macosx-10.6-i386/egg/suds/mx/core.py", line 75, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 102, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 243, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 182, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/core.py", line 75, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 102, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 298, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 182, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/core.py", line 75, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 102, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 298, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 182, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/core.py", line 75, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 102, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 243, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 182, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/core.py", line 75, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 102, in append File "build/bdist.macosx-10.6-i386/egg/suds/mx/appender.py", line 198, in append File "build/bdist.macosx-10.6-i386/egg/suds/sax/element.py", line 251, in setText File "build/bdist.macosx-10.6-i386/egg/suds/sax/text.py", line 43, in __new__ UnicodeDecodeError: 'ascii' codec can't decode byte 0xc3 in position 116: ordinal not in range(128) Now what? My guess is my script can take in these funky chars because I have # -*- coding: utf-8 -*- at the top but Suds does NOT have that at the top of its files. Do I really want to go and change the Suds files...we all know this is the least desired last possible solution...what can I do?

  Read the article

• Random Access Violation Exception in WPF Application

  - by PT1984

  Hi, I am facing weird problem while running regression tests on my WPF Application. I am getting AccessViolationException with different stacktraces each time. First : Message :Attempted to read or write protected memory. This is often an indication that other memory is corrupt. StackTrace : at MS.Win32.PresentationCore.UnsafeNativeMethods.MILUnknown.Release(IntPtr pIUnkown) at MS.Win32.PresentationCore.UnsafeNativeMethods.MILUnknown.ReleaseInterface(IntPtr& ptr) at System.Windows.Media.SafeMILHandle.ReleaseHandle() at System.Runtime.InteropServices.SafeHandle.InternalFinalize() at System.Runtime.InteropServices.SafeHandle.Dispose(Boolean disposing) at System.Runtime.InteropServices.SafeHandle.Finalize() Source :PresentationCore Type : System.AccessViolationException. Second : Message :Attempted to read or write protected memory. This is often an indication that other memory is corrupt. StackTrace : at MS.Win32.PresentationCore.UnsafeNativeMethods.IMILBitmapEffect.GetOutput(SafeHandle THIS_PTR, UInt32 uiIndex, SafeMILHandle pContext, BitmapSourceSafeMILHandle& ppBitmapSource) at System.Windows.Media.Effects.BitmapEffect.GetOutput(SafeHandle unmanagedEffect, Int32 index, BitmapEffectRenderContext context) at System.Windows.Media.Effects.BitmapEffect.GetOutput(BitmapEffectInput input) at System.Windows.Media.Effects.BitmapEffectState.GetEffectOutput(Visual visual, RenderTargetBitmap& renderBitmap, Matrix worldTransform, Rect windowClip, Matrix& finalTransform) at System.Windows.Media.Effects.BitmapEffectVisualState.RenderBitmapEffect(Visual visual, Channel channel) at System.Windows.Media.Effects.BitmapEffectContent.ExecuteRealizationsUpdate() at System.Windows.Media.RealizationContext.RealizationUpdateSchedule.Execute() at System.Windows.Media.MediaContext.Render(ICompositionTarget resizedCompositionTarget) at System.Windows.Media.MediaContext.RenderMessageHandlerCore(Object resizedCompositionTarget) at System.Windows.Media.MediaContext.AnimatedRenderMessageHandler(Object resizedCompositionTarget) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Boolean isSingleParameter) at System.Windows.Threading.ExceptionWrapper.TryCatchWhen(Object source, Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.Dispatcher.WrappedInvoke(Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.DispatcherOperation.InvokeImpl() at System.Windows.Threading.DispatcherOperation.InvokeInSecurityContext(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Threading.DispatcherOperation.Invoke() at System.Windows.Threading.Dispatcher.ProcessQueue() at System.Windows.Threading.Dispatcher.WndProcHook(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndWrapper.WndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndSubclass.DispatcherCallbackOperation(Object o) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Boolean isSingleParameter) at System.Windows.Threading.ExceptionWrapper.TryCatchWhen(Object source, Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.Dispatcher.WrappedInvoke(Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.Dispatcher.InvokeImpl(DispatcherPriority priority, TimeSpan timeout, Delegate method, Object args, Boolean isSingleParameter) at System.Windows.Threading.Dispatcher.Invoke(DispatcherPriority priority, Delegate method, Object arg) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam) at MS.Win32.UnsafeNativeMethods.DispatchMessage(MSG& msg) at System.Windows.Threading.Dispatcher.PushFrameImpl(DispatcherFrame frame) at System.Windows.Threading.Dispatcher.PushFrame(DispatcherFrame frame) at System.Windows.Threading.Dispatcher.Run() at System.Windows.Application.RunDispatcher(Object ignore) at System.Windows.Application.RunInternal(Window window) at System.Windows.Application.Run(Window window) at System.Windows.Application.Run() at Main() Source :PresentationCore Type :System.AccessViolationException In Application Event Log I found following entries : Dispatcher processing has been suspended, but messages are still being processed. Faulting application **.exe, version 1.0.0.*, stamp 4c08d288, faulting module wpfgfx_v0300.dll, version 3.0.6920.1427, stamp 488f3056, debug? 0, fault address 0x0012ec36. My Application uses Dispatcher from another thread, to change the values of the controls , enable - disable those, change visibility etc., the thred is run multiple times in a second. Please let me know if anybody has faced this problem? Thanks in advance, -Prasad

  Read the article

• Python: combine logging and wx so that logging stream is redirectet to stdout/stderr frame

  - by Uwe

  Here's the thing: I'm trying to combine the logging module with wx.App()'s redirect feature. My intention is to log to a file AND to stderr. But I want stderr/stdout redirected to a separate frame as is the feature of wx.App. My test code: import logging import wx class MyFrame(wx.Frame): def __init__(self): self.logger = logging.getLogger("main.MyFrame") wx.Frame.__init__(self, parent = None, id = wx.ID_ANY, title = "MyFrame") self.logger.debug("MyFrame.__init__() called.") def OnExit(self): self.logger.debug("MyFrame.OnExit() called.") class MyApp(wx.App): def __init__(self, redirect): self.logger = logging.getLogger("main.MyApp") wx.App.__init__(self, redirect = redirect) self.logger.debug("MyApp.__init__() called.") def OnInit(self): self.frame = MyFrame() self.frame.Show() self.SetTopWindow(self.frame) self.logger.debug("MyApp.OnInit() called.") return True def OnExit(self): self.logger.debug("MyApp.OnExit() called.") def main(): logger_formatter = logging.Formatter("%(name)s\t%(levelname)s\t%(message)s") logger_stream_handler = logging.StreamHandler() logger_stream_handler.setLevel(logging.INFO) logger_stream_handler.setFormatter(logger_formatter) logger_file_handler = logging.FileHandler("test.log", mode = "w") logger_file_handler.setLevel(logging.DEBUG) logger_file_handler.setFormatter(logger_formatter) logger = logging.getLogger("main") logger.setLevel(logging.DEBUG) logger.addHandler(logger_stream_handler) logger.addHandler(logger_file_handler) logger.info("Logger configured.") app = MyApp(redirect = True) logger.debug("Created instance of MyApp. Calling MainLoop().") app.MainLoop() logger.debug("MainLoop() ended.") logger.info("Exiting program.") return 0 if (__name__ == "__main__"): main() Expected behavior is: - a file is created named test.log - the file contains logging messages with level DEBUG and INFO/ERROR/WARNING/CRITICAL - messages from type INFO and ERROR/WARNING/CRITICAL are ether shown on the console or in a separate frame, depending on where they are created - logger messages that are not inside MyApp or MyFrame are displayed at the console - logger messages from inside MyApp or MyFrame are shown in a separate frame Actual behavior is: - The file is created and contains: main INFO Logger configured. main.MyFrame DEBUG MyFrame.__init__() called. main.MyFrame INFO MyFrame.__init__() called. main.MyApp DEBUG MyApp.OnInit() called. main.MyApp INFO MyApp.OnInit() called. main.MyApp DEBUG MyApp.__init__() called. main DEBUG Created instance of MyApp. Calling MainLoop(). main.MyApp DEBUG MyApp.OnExit() called. main DEBUG MainLoop() ended. main INFO Exiting program. - Console output is: main INFO Logger configured. main.MyFrame INFO MyFrame.__init__() called. main.MyApp INFO MyApp.OnInit() called. main INFO Exiting program. - No separate frame is opened, although the lines main.MyFrame INFO MyFrame.__init__() called. main.MyApp INFO MyApp.OnInit() called. shouldget displayed within a frame and not on the console. It seems to me that wx.App can't redirect stderr to a frame as soon as a logger instance uses stderr as output. wxPythons Docs claim the wanted behavior though, see here. Any ideas? Uwe

  Read the article

• Inconsistent responses from ISAPI DLL in mod_isapi.

  - by William Leader

  I have a ISAPI dll which I created with Delphi 2009, and I have been able to test that it functions as designed when I run it inside of IIS 5.1. However when I attempt to host the web service from within Apache on Windows XP using mod_isapi, I do not get consistent results. The ISAPI dll implements a very simple SOAP service with two methods. One method is a simple echo service that sends back the string sent to it. The second method is used to send a file to the server using a TSoapAttachement (Mutipart MIME). The interface can be descibes as follows IPdiSvc2 = interface(IInvokable) ['{532DCDD7-D66B-4D2C-924E-2F389D3E0A74}'] function Echo(data:string): string; stdcall; function SendFile(request:TFileDescription; attachment: TSOAPAttachment): TSendFileResponse; stdcall; end; What is interesting is if I only call the echo function Apache handles this without error every time. The webservice only returns an error after calling send File, but not every time. There are three outcomes to calling send file that I have observed: A normal result without an error (HTTP 200 OK). A Soap encoded exception with the message: 'Required white space was missing. Line: 11 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML.' (HTTP 500 Internal Error). This also generates a message in the Apache error.log 'Premature end of script headers: MYISAPI.dll' A Soap encoded exception with the message: 'Access violation at address 01A53D57 in module MYISAPI.dll. Read of address 00000000.' (HTTP 200 OK). What I find interesting is that the second third outcomes still occur if I call echo after calling send file. Calling SendFile, SendFile, SendFile, SendFile results in outcomes 1, 2, 3, 1. Calling Echo, SendFile, SendFile, SendFile results in outcomes 1, 1, 2, 3. Calling SendFile, Echo, Echo, SendFile results in outcomes 1, 2, 3, 1. The pattern I am seing is that after a Successful SendFile, the next to requests result in outcomes 2 and 3 regardless of what those two requests are. My guess is that because Apache uses multiple threads to handle multiple requests that each request is getting handled in a slightly different way, and that the DLL may not have been initialized in the same way for each worker thread. I do not think the problem exists in my code as when I attach the debugger to httpd.exe it does recognize the exceptions but it says the exceptions are in non-delphi code meaning that they are happening before the code inside my DLL has a chance to execute. I suspect it may have something to do with the way I have apache configured. My Apache configuration is the defaults created by the 2.2.15 installer for windows with the following addition: <IfModule isapi_module> AddHandler isapi-handler .dll ISAPILogNotSupported on ISAPIFakeAsync on ISAPIAppendLogToErrors on </IfModule> <IfModule alias_module> ScriptAlias /myisapi/ "C:/path/to/myisapi/" </IfModule> <Directory "C:/path/to/myisapi/"> AllowOverride None Options ExecCGI Order allow,deny Allow from all </Directory>

  Read the article

• Nasty mono bug with F#

  - by Aurimas Anskaitis

  Hi, I have this monstrous f# 2.0 program My mono version is Mono JIT compiler version 2.9 (master/f593354 Sun Dec 26 03:15:55 EET 2010) Copyright (C) 2002-2010 Novell, Inc and Contributors. www.mono-project.com TLS: __thread SIGSEGV: altstack Notifications: epoll Architecture: x86 Disabled: none Misc: softdebug LLVM: supported, not enabled. GC: Included Boehm (with typed GC and Parallel Mark) //--------------------------------------------- module Main let rec gcd x y = if y = 0 then x else gcd y (x%y) let main = printfn "%i" (gcd 4 2) main //----------------------------------------------- And the problem is that output from running the program is as follows: Stacktrace: at (wrapper managed-to-native) System.Reflection.MonoMethodInfo.get_parameter_info (intptr,System.Reflection.MemberInfo) <0xffffffff at System.Reflection.MonoMethodInfo.GetParametersInfo (intptr,System.Reflection.MemberInfo) <0x00013 at System.Reflection.MonoCMethod.GetParameters () <0x00015 at System.Reflection.MonoCMethod.Invoke (object,System.Reflection.BindingFlags,System.Reflection.Binder,object[],System.Globalization.CultureInfo) <0x00035 at System.Reflection.MonoCMethod.Invoke (System.Reflection.BindingFlags,System.Reflection.Binder,object[],System.Globalization.CultureInfo) <0x00024 at System.Reflection.ConstructorInfo.Invoke (object[]) <0x0003f at System.Activator.CreateInstance (System.Type,bool) <0x0017c at System.Activator.CreateInstance (System.Type) <0x00012 at Microsoft.FSharp.Reflection.FSharpValue.MakeFunction (System.Type,Microsoft.FSharp.Core.FSharpFunc2<object, object>) <0x00145> at Microsoft.FSharp.Core.PrintfImpl.capture@529<b, c, d> (Microsoft.FSharp.Core.FSharpFunc2, Microsoft.FSharp.Core.FSharpFunc`2<char, Microsoft.FSharp.Core.Unit>, Microsoft.FSharp.Core.FSharpFunc`2,string,int,Microsoft.FSharp.Collections.FSharpList1<object>,System.Type,int) <0x00147> at Microsoft.FSharp.Core.PrintfImpl.gprintf<b, c, d, a> (Microsoft.FSharp.Core.FSharpFunc2, Microsoft.FSharp.Core.FSharpFunc`2<char, Microsoft.FSharp.Core.Unit>, Microsoft.FSharp.Core.FSharpFunc`2,Microsoft.FSharp.Core.PrintfFormat4<a, b, c, d>) <0x000dd> at Microsoft.FSharp.Core.PrintfModule.kprintf_imperative<a, b, c> (Microsoft.FSharp.Core.FSharpFunc2,b,Microsoft.FSharp.Core.FSharpFunc2<char, Microsoft.FSharp.Core.Unit>,Microsoft.FSharp.Core.PrintfFormat4) <0x00058 at Microsoft.FSharp.Core.PrintfModule.PrintFormatToTextWriterThen (Microsoft.FSharp.Core.FSharpFunc2<Microsoft.FSharp.Core.Unit, TResult>,System.IO.TextWriter,Microsoft.FSharp.Core.PrintfFormat4) <0x0004d at Microsoft.FSharp.Core.PrintfModule.PrintFormatLineToTextWriter (System.IO.TextWriter,Microsoft.FSharp.Core.PrintfFormat`4) <0x0004d at .$Main.main@ () <0x00042 Native stacktrace: mono() [0x80dc13b] mono() [0x811c65b] mono() [0x8059a11] [0x7af40c] mono() [0x8228214] mono() [0x8228214] mono() [0x8228214] mono() [0x8228214] mono() [0x8228214] mono() [0x8228214] mono() [0x8228214] mono() [0x8228214] mono() [0x8228282] mono() [0x822991e] mono() [0x822aa9d] mono(mono_array_new_specific+0xea) [0x813ba9a] mono() [0x81c63a1] mono() [0x8149ac8] [0xc04328] [0xc042e4] [0xc042be] [0xc0455e] [0xc0451d] [0xc044d8] [0xc0349d] [0xc0330b] [0xc02f9e] [0xbfe960] [0xbfe6c6] [0xbfe571] [0xbfe4de] [0xbfe44e] [0xbf9d2b] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] [0x9bf0724] Debug info from gdb: Could not attach to process. If your uid matches the uid of the target process, check the setting of /proc/sys/kernel/yama/ptrace_scope, or try again as the root user. For more details, see /etc/sysctl.d/10-ptrace.conf ptrace: Operation not permitted. ================================================================= Got a SIGSEGV while executing native code. This usually indicates a fatal error in the mono runtime or one of the native libraries used by your application. Aborted It is a huge problem with mono or f#? By the way, the same function works when using pattern matching instead of "if".

  Read the article

• java.util.zip.ZipException in Glassfish (v3) application deployment

  - by Kevin

  Hello, I've got a strange exception with my EJB3.1 application, a ZipException is thrown during the application deployment: [#|2010-05-15T16:01:44.688+0100|SEVERE|glassfish3.0.1|javax.enterprise.system.container.web.org.glassfish.web.loader|_ThreadID=22;_ThreadName=Thread-1;|WEB9051: Error trying to scan the classes at /Users/kevin/Documents/netbeans/WebAlbums/trunk/WebAlbums3/WebAlbums3-ea/dist/gfdeploy/WebAlbums3-Service.jar for annotations in which a ServletContainerInitializer has expressed interest java.util.zip.ZipException: error in opening zip file at java.util.zip.ZipFile.open(Native Method) at java.util.zip.ZipFile.<init>(ZipFile.java:114) at java.util.jar.JarFile.<init>(JarFile.java:133) at java.util.jar.JarFile.<init>(JarFile.java:70) at org.glassfish.web.loader.ServletContainerInitializerUtil.getInitializerList(ServletContainerInitializerUtil.java:255) at org.apache.catalina.core.StandardContext.callServletContainerInitializers(StandardContext.java:5331) at com.sun.enterprise.web.WebModule.callServletContainerInitializers(WebModule.java:550) at org.apache.catalina.core.StandardContext.start(StandardContext.java:5263) at com.sun.enterprise.web.WebModule.start(WebModule.java:499) at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:928) at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:912) at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:694) at com.sun.enterprise.web.WebContainer.loadWebModule(WebContainer.java:1947) at com.sun.enterprise.web.WebContainer.loadWebModule(WebContainer.java:1619) at com.sun.enterprise.web.WebApplication.start(WebApplication.java:90) at org.glassfish.internal.data.EngineRef.start(EngineRef.java:126) at org.glassfish.internal.data.ModuleInfo.start(ModuleInfo.java:241) at org.glassfish.internal.data.ApplicationInfo.start(ApplicationInfo.java:236) at com.sun.enterprise.v3.server.ApplicationLifecycle.deploy(ApplicationLifecycle.java:339) at com.sun.enterprise.v3.server.ApplicationLifecycle.deploy(ApplicationLifecycle.java:183) at org.glassfish.deployment.admin.DeployCommand.execute(DeployCommand.java:272) at com.sun.enterprise.v3.admin.CommandRunnerImpl$1.execute(CommandRunnerImpl.java:305) at com.sun.enterprise.v3.admin.CommandRunnerImpl.doCommand(CommandRunnerImpl.java:320) at com.sun.enterprise.v3.admin.CommandRunnerImpl.doCommand(CommandRunnerImpl.java:1176) at com.sun.enterprise.v3.admin.CommandRunnerImpl.access$900(CommandRunnerImpl.java:83) at com.sun.enterprise.v3.admin.CommandRunnerImpl$ExecutionContext.execute(CommandRunnerImpl.java:1235) at com.sun.enterprise.v3.admin.CommandRunnerImpl$ExecutionContext.execute(CommandRunnerImpl.java:1224) at com.sun.enterprise.v3.admin.AdminAdapter.doCommand(AdminAdapter.java:365) at com.sun.enterprise.v3.admin.AdminAdapter.service(AdminAdapter.java:204) at com.sun.grizzly.tcp.http11.GrizzlyAdapter.service(GrizzlyAdapter.java:166) at com.sun.enterprise.v3.server.HK2Dispatcher.dispath(HK2Dispatcher.java:100) at com.sun.enterprise.v3.services.impl.ContainerMapper.service(ContainerMapper.java:245) at com.sun.grizzly.http.ProcessorTask.invokeAdapter(ProcessorTask.java:791) at com.sun.grizzly.http.ProcessorTask.doProcess(ProcessorTask.java:693) at com.sun.grizzly.http.ProcessorTask.process(ProcessorTask.java:954) at com.sun.grizzly.http.DefaultProtocolFilter.execute(DefaultProtocolFilter.java:170) at com.sun.grizzly.DefaultProtocolChain.executeProtocolFilter(DefaultProtocolChain.java:135) at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:102) at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:88) at com.sun.grizzly.http.HttpProtocolChain.execute(HttpProtocolChain.java:76) at com.sun.grizzly.ProtocolChainContextTask.doCall(ProtocolChainContextTask.java:53) at com.sun.grizzly.SelectionKeyContextTask.call(SelectionKeyContextTask.java:57) at com.sun.grizzly.ContextTask.run(ContextTask.java:69) at com.sun.grizzly.util.AbstractThreadPool$Worker.doWork(AbstractThreadPool.java:330) at com.sun.grizzly.util.AbstractThreadPool$Worker.run(AbstractThreadPool.java:309) at java.lang.Thread.run(Thread.java:637) |#] I don't really know how to investigate this error; I know that it's not related to the glassfish installation (same problem on Ubuntu and Mac) ... I spot a 'null' in the classpath definition (log level fine), maybe that's the reason, but I don't know how to get rid of it ... [#|2010-05-15T16:01:44.672+0100|FINE|glassfish3.0.1|javax.enterprise.system.container.web.com.sun.enterprise.web|_ThreadID=22;_ThreadName=Thread-1;ClassName=com.sun.enterprise.web.WebModuleListener;MethodName=configureJsp;| sysClasspath for WebAlbums3-ea#WebAlbums3-Servlet.war is /Users/kevin/apps/glassfishv3/glassfish/modules/antlr-repackaged.jar:...:/Users/kevin/apps/glassfishv3/glassfish/modules/gf-client-module.jar:/Users/kevin/apps/glassfishv3/glassfish/modules/javax.security.auth.message.jar:null:/Users/kevin/apps/glassfishv3/glassfish/modules/org.eclipse.persistence.antlr.jar:/Users/kevin/apps/glassfishv3/glassfish/domains/domain1/lib/classes:/Users/kevin/apps/glassfishv3/glassfish/domains/domain1/lib/RT-DB-mysql-connector-java-5.1.12-bin.jar:|#] (I'm using Netbeans 6.8, Glassfish v3, Servlet3, EJB 3.1, JPA/Hibernate) Thank you for your help

  Read the article

• Windows Server 2008 R2 + IIS 7.5 + ASP.NET 4.0 = HTTP Error 500.0

  - by Dave

  I am having an impossible time getting asp.net 4.0 to work in any fashion at all. In fact, I completely wiped my server, reinstalled with Server 2008 R2 Standard (running on a VMWare ESXi box, not that it should matter), and cannot even get a test .aspx page to work. Here is exactly what I did: Installed 2008 R2 Standard Activated windows and enabled Remote Desktop Installed the Web Server Role with the necessary role services(common http, asp.net, logging, tracing, management service and FTP) Enabled the management service Installed .Net Framework 4.0 via web executable Added FTP publishing to the default web site Switched default web site application pool to asp.net 4.0 (integrated) Added a 'test.aspx' file to the inetpub\wwwroot folder (contents below) Opened a browser to http://localhost/test.aspx and received a 500.0 error (also below) What am I missing? I haven't touched IIS in a while (3+ years), so it could be something stupid/trvial. Please point it out, call me a noob; my ego can take it. Thanks, Dave test.aspx <% @Page language="C# %> <html> <head> <title>Test.aspx</title> </head> <body> <asp:label runat="server" text="This is an asp.net 4.0 label" /> </body> </html> Error page: Module AspNetInitClrHostFailureModule Notification BeginRequest Handler PageHandlerFactory-Integrated-4.0 Error Code 0x80070002 Requested URL http://localhost:80/test.aspx Physical Path C:\inetpub\wwwroot\test.aspx Logon Method Not yet determined Logon User Not yet determined Trace: And in my trace file I get: 96. view trace Warning -SET_RESPONSE_ERROR_DESCRIPTION ErrorDescription An error message detailing the cause of this specific request failure can be found in the application event log of the web server. Please review this log entry to discover what caused this error to occur. 97. view trace Warning -MODULE_SET_RESPONSE_ERROR_STATUS ModuleName AspNetInitClrHostFailureModule Notification 1 HttpStatus 500 HttpReason Internal Server Error HttpSubStatus 0 ErrorCode 2147942402 ConfigExceptionInfo Notification BEGIN_REQUEST ErrorCode The system cannot find the file specified. (0x80070002) The application error log shows: Log Name: Application Source: Microsoft-Windows-IIS-W3SVC-WP Date: 5/28/2010 2:08:10 PM Event ID: 2299 Task Category: None Level: Error Keywords: Classic User: N/A Computer: win-ltfkdo1dnfp Description: An application has reported as being unhealthy. The worker process will now request a recycle. Reason given: An error message detailing the cause of this specific request failure can be found in the application event log of the web server. Please review this log entry to discover what caused this error to occur. The data is the error. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-IIS-W3SVC-WP" Guid="{670080D9-742A-4187-8D16-41143D1290BD}" EventSourceName="W3SVC-WP" /> <EventID Qualifiers="49152">2299</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2010-05-28T21:08:10.000000000Z" /> <EventRecordID>1663</EventRecordID> <Correlation /> <Execution ProcessID="0" ThreadID="0" /> <Channel>Application</Channel> <Computer>win-ltfkdo1dnfp</Computer> <Security /> </System> <EventData> <Data Name="Reason">An error message detailing the cause of this specific request failure can be found in the application event log of the web server. Please review this log entry to discover what caused this error to occur. </Data> <Binary>02000780</Binary> </EventData> </Event>

  Read the article

• Using amCharts in Ruby on Rails

  - by Dexter

  I have followed this tutorial in order to use amChart and it worked with no problems , now I am trying to generate a chart with amCharts to show each user and the sign in count but i cant make it work because it not getting the data correctly, what i am missing here ? how can i show user email and sign_in_count ? Users_controller.rb class UsersController < ApplicationController load_and_authorize_resource def index @users = User.all respond_to do |format| format.html # index.html.erb format.json { render :json => @users } end end def show @user = User.find(params[:id]) end def new @user = User.new end def create @user = User.new(params[:user]) if @user.save flash[:notice] = 'A new user created successfully.' redirect_to users_path else flash[:error] = 'An error occurred please try again!' redirect_to users_path end end def edit @user = User.find(params[:id]) end def update @user = User.find(params[:id]) if @user.update_attributes(params[:user]) flash[:notice] = 'Profile updated' redirect_to users_path else render 'edit' end end def destroy @user = User.find(params[:id]) if current_user == (@user) flash[:error] = "Admin suicide warning: Can't delete yourself." else @user.destroy flash[:notice] = 'User deleted' redirect_to users_path end end def checkname if User.where('user_name = ?', params[:user]).count == 0 render :nothing => true, :status => 200 else render :nothing => true, :status => 409 end return end end Users_helper.rb module UsersHelper def convert_to_amcharts_json(data_array) data_array.to_json.gsub(/\"text\"/, "text").html_safe end end index.html.erb <div id="chartdiv" style="width: 100%; height: 400px;"></div> <script type="text/javascript"> var chart; var chartData = <%= convert_to_amcharts_json(@users) %>; AmCharts.ready(function () { // SERIAL CHART chart = new AmCharts.AmSerialChart(); chart.dataProvider = chartData; chart.categoryField = "email"; // the following two lines makes chart 3D chart.depth3D = 20; chart.angle = 30; // AXES // category var categoryAxis = chart.categoryAxis; categoryAxis.labelRotation = 90; categoryAxis.dashLength = 5; categoryAxis.gridPosition = "start"; // value var valueAxis = new AmCharts.ValueAxis(); valueAxis.title = "Most Active users"; valueAxis.dashLength = 5; chart.addValueAxis(valueAxis); // GRAPH var graph = new AmCharts.AmGraph(); graph.valueField = "sign_in_count"; graph.colorField = "color"; graph.balloonText = "<span style='font-size:14px'>[[category]]: <b>[[value]]</b></span>"; graph.type = "column"; graph.lineAlpha = 0; graph.fillAlphas = 1; chart.addGraph(graph); // CURSOR var chartCursor = new AmCharts.ChartCursor(); chartCursor.cursorAlpha = 0; chartCursor.zoomable = false; chartCursor.categoryBalloonEnabled = false; chart.addChartCursor(chartCursor); // WRITE chart.write("chartdiv"); }); </script>

  Read the article

• Trouble determining proper decoding of a REST response from an ArcGIS REST service using IHttpModule

  - by Ryan Taylor

  First a little background on what I am trying to achieve. I have an application that is utilizing REST services served by ArcGIS Server and IIS7. The REST services return data in one of several different formats. I am requesting a JSON response. I want to be able to modify the response (remove or add parameters) before the response is sent to the client. However, I am having difficulty converting the stream to a string that I can modify. To that end, I have implemented the following code in order to try to inspect the stream. SecureModule.cs using System; using System.Web; namespace SecureModuleTest { public class SecureModule : IHttpModule { public void Init(HttpApplication context) { context.BeginRequest += new EventHandler(OnBeginRequest); } public void Dispose() { } public void OnBeginRequest(object sender, EventArgs e) { HttpApplication application = (HttpApplication) sender; HttpContext context = application.Context; HttpRequest request = context.Request; HttpResponse response = context.Response; response.Filter = new ServicesFilter(response.Filter); } } } ServicesFilter.cs using System; using System.IO; using System.Text; namespace SecureModuleTest { class ServicesFilter : MemoryStream { private readonly Stream _outputStream; private StringBuilder _content; public ServicesFilter(Stream output) { _outputStream = output; _content = new StringBuilder(); } public override void Write(byte[] buffer, int offset, int count) { _content.Append(Encoding.UTF8.GetString(buffer, offset, count)); using (TextWriter textWriter = new StreamWriter(@"C:\temp\content.txt", true)) { textWriter.WriteLine(String.Format("Buffer: {0}", _content.ToString())); textWriter.WriteLine(String.Format("Length: {0}", buffer.Length)); textWriter.WriteLine(String.Format("Offset: {0}", offset)); textWriter.WriteLine(String.Format("Count: {0}", count)); textWriter.WriteLine(""); textWriter.Close(); } // Modify response _outputStream.Write(buffer, offset, count); } } } The module is installed in the /ArcGIS/rest/ virtual directory and is executed via the following GET request. http://localhost/ArcGIS/rest/services/?f=json&pretty=true The web page displays the expected response, however, the text file tells a very different (encoded?) story. Expect Response {"currentVersion" : "10.0", "folders" : [], "services" : [ ] } Text File Contents Buffer: ? ?`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q? Length: 4096 Offset: 0 Count: 168 Buffer: ? ?`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q?K???!P Length: 4096 Offset: 0 Count: 11 Interestingly, Fiddler depicts a similar picture. Fiddler Request GET http://localhost/ArcGIS/rest/services/?f=json&pretty=true HTTP/1.1 Host: localhost Connection: keep-alive User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.70 Safari/533.4 Referer: http://localhost/ArcGIS/rest/services Cache-Control: no-cache Pragma: no-cache Accept: application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Cookie: a=mWz_JFOusuGPnS3w5xx1BSUuyKGB3YZo92Dy2SUntP2MFWa8MaVq6a4I_IYBLKuefXDZANQMeqvxdGBgQoqTKz__V5EQLHwxmKlUNsaK7do. Fiddler Response - Before Clicking Decode HTTP/1.1 200 OK Content-Type: text/plain;charset=utf-8 Content-Encoding: gzip ETag: 719143506 Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Thu, 10 Jun 2010 01:08:43 GMT Content-Length: 179 ????????`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q?K???! P??? Fiddler Response - After Clicking Decode HTTP/1.1 200 OK Content-Type: text/plain;charset=utf-8 ETag: 719143506 Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Thu, 10 Jun 2010 01:08:43 GMT Content-Length: 80 {"currentVersion" : "10.0", "folders" : [], "services" : [ ] } I think that the problem may be a result of compression and/or chunking of data (this might be why I am receiving two calls to ServicesFilter.Write(...), however, I have not yet been able to solve the issue. How might I decode, unzip, and otherwise convert the byte stream into the string I know it should be for modification by my filter?

  Read the article

• Weird call stack when application has frozen

  - by Harriv

  I apparently have an dead lock problem in one of my applications and started investigating EurekaLog stack traces. Here's one recent: Call Stack Information: -------------------------------------------------------------------------------------------------------------------------------------- |Address |Module |Unit |Class |Procedure/Method |Line | -------------------------------------------------------------------------------------------------------------------------------------- |*Exception Thread: ID=14208; Priority=0; Class=; [Main] | |------------------------------------------------------------------------------------------------------------------------------------| |7C82860C|ntdll.dll | | |KiFastSystemCall | | |7C827D27|ntdll.dll | | |ZwWaitForSingleObject | | |77E61C96|kernel32.dll | | |WaitForSingleObjectEx | | |77E61C88|kernel32.dll | | |WaitForSingleObject | | |77E61C7B|kernel32.dll | | |WaitForSingleObject | | |004151C4|MyApp.exe |sysutils.pas |TMultiReadExclusiveWriteSynchronizer|WaitForWriteSignal |16740[1] | |004151BC|MyApp.exe |sysutils.pas |TMultiReadExclusiveWriteSynchronizer|WaitForWriteSignal |16740[1] | |0041522C|MyApp.exe |sysutils.pas |TMultiReadExclusiveWriteSynchronizer|BeginWrite |16818[57] | |004323FB|MyApp.exe |Classes.pas |TDataModule |Create |11357[1] | |004323C0|MyApp.exe |Classes.pas |TDataModule |Create |11356[0] | |007D744D|MyApp.exe |uRORemoteDataModule.pas |TRORemoteDataModule |Create |163[1] | |007D7434|MyApp.exe |uRORemoteDataModule.pas |TRORemoteDataModule |Create |162[0] | |007DBFAB|MyApp.exe |Sentrol_Impl.pas | |Create_Sentrol |85[1] | |00646952|MyApp.exe |uROServer.pas |TROInvoker |CustomHandleMessage |726[11] | |00407BFA|MyApp.exe |system.pas |TInterfacedObject |_AddRef |17972[1] | |00404934|MyApp.exe |system.pas |TObject |GetInterface |9003[8] | |00407B1C|MyApp.exe |system.pas | |_IntfClear |17817[1] | |00404966|MyApp.exe |system.pas |TObject |GetInterface |9009[14] | |004048E8|MyApp.exe |system.pas |TObject |GetInterface |8995[0] | |00407BD7|MyApp.exe |system.pas |TInterfacedObject |QueryInterface |17964[1] | |77E61680|kernel32.dll | | |InterlockedDecrement | | |00407C10|MyApp.exe |system.pas |TInterfacedObject |_Release |17977[1] | |00407B2C|MyApp.exe |system.pas | |_IntfClear |17824[8] | |004067DF|MyApp.exe |system.pas | |_FinalizeArray |15233[100]| |00407B1C|MyApp.exe |system.pas | |_IntfClear |17817[1] | |00646577|MyApp.exe |uROServer.pas |TROClassFactoryList |FindClassFactoryByInterfaceName|619[17] | |77E6166C|kernel32.dll | | |InterlockedIncrement | | |00407BFA|MyApp.exe |system.pas |TInterfacedObject |_AddRef |17972[1] | |00646B72|MyApp.exe |uROServer.pas |TROInvoker |HandleMessage |758[1] | |006460C5|MyApp.exe |uROServer.pas | |MainProcessMessage |512[98] | |00645BAC|MyApp.exe |uROServer.pas | |MainProcessMessage |414[0] | |00647184|MyApp.exe |uROServer.pas |TROMessageDispatcher |ProcessMessage |929[2] | |00647130|MyApp.exe |uROServer.pas |TROMessageDispatcher |ProcessMessage |927[0] | |00647BCF|MyApp.exe |uROServer.pas |TROServer |IntDispatchMessage |1328[27] | |00647ABC|MyApp.exe |uROServer.pas |TROServer |IntDispatchMessage |1301[0] | |0064782F|MyApp.exe |uROServer.pas |TROServer |DispatchMessage |1170[11] | |006477B4|MyApp.exe |uROServer.pas |TROServer |DispatchMessage |1159[0] | |006477A9|MyApp.exe |uROServer.pas |TROServer |DispatchMessage |1152[1] | |0064779C|MyApp.exe |uROServer.pas |TROServer |DispatchMessage |1151[0] | |00659CB6|MyApp.exe |uROLocalServer.pas |TROLocalServer |SendRequest |57[1] | |00659CA4|MyApp.exe |uROLocalServer.pas |TROLocalServer |SendRequest |56[0] | |0065A009|MyApp.exe |uROLocalChannel.pas |TROLocalChannel |IntDispatch |99[10] | |005EE540|MyApp.exe |uROClient.pas |TROTransportChannel |Dispatch |1884[36] | |005EE3FC|MyApp.exe |uROClient.pas |TROTransportChannel |Dispatch |1848[0] | |005EEC8F|MyApp.exe |uROClient.pas |TROTransportChannel |Dispatch |2134[27] | |00616EC8|MyApp.exe |PCCS_Intf.pas |TSentrol_Proxy |GetNewValues |6585[7] | |007CBDB9|MyApp.exe |ETAROConnectionForm.pas |TROConnectionForm |SyncSentrolUpdateTimerTimer |855[16] | |7C82ABE5|ntdll.dll | | |RtlTimeToTimeFields | | |004D5D9C|MyApp.exe |Controls.pas |TControl |WndProc |5063[0] | |004DA05B|MyApp.exe |Controls.pas |TWinControl |WndProc |7304[111] | |7C81A3AB|ntdll.dll | | |RtlLeaveCriticalSection | | |0042659C|MyApp.exe |Classes.pas |TThreadList |UnlockList |3359[1] | |00426598|MyApp.exe |Classes.pas |TThreadList |UnlockList |3359[1] | |004935BC|MyApp.exe |Graphics.pas | |FreeMemoryContexts |5060[12] | |00493524|MyApp.exe |Graphics.pas | |FreeMemoryContexts |5048[0] | |004D9799|MyApp.exe |Controls.pas |TWinControl |MainWndProc |7076[6] | |004329F4|MyApp.exe |Classes.pas | |StdWndProc |11583[8] | |7739C09A|USER32.dll | | |CallNextHookEx | | |004B1343|MyApp.exe |ExtCtrls.pas |TTimer |Timer |2281[1] | |00404A30|MyApp.exe |system.pas | |_CallDynaInst |9159[1] | |004B1227|MyApp.exe |ExtCtrls.pas |TTimer |WndProc |2239[4] | |004329F4|MyApp.exe |Classes.pas | |StdWndProc |11583[8] | |7739C42C|USER32.dll | | |GetParent | | |7739C45C|USER32.dll | | |GetParent | | |773A16E0|USER32.dll | | |DispatchMessageA | | |773A16D6|USER32.dll | | |DispatchMessageA | | |004CC234|MyApp.exe |Forms.pas |TApplication |ProcessMessage |8105[23] | |004CC138|MyApp.exe |Forms.pas |TApplication |ProcessMessage |8082[0] | |004CC26E|MyApp.exe |Forms.pas |TApplication |HandleMessage |8124[1] | |004CC264|MyApp.exe |Forms.pas |TApplication |HandleMessage |8123[0] | |004CC563|MyApp.exe |Forms.pas |TApplication |Run |8223[20] | |004CC4B0|MyApp.exe |Forms.pas |TApplication |Run |8203[0] | |007F18B3|MyApp.exe |MyApp.dpr | | |215[65] | The stack trace seems to be ok until first TTimer call, after that it contains some garbage(?), however the end contains the the lock which seems be holding the main thread. Can I trust this stack trace? If not, what can cause this and how I can avoid it? Any ideas about the dead lock based on this stack trace? I don't quite understand how creating a datamodule can dead lock.. I'm using Delphi 2007.

  Read the article

• Delphi 7 SOAP Authentication and SessionID HowTo

  - by Justin Philbrow

  Hello All, I am developing a 3 tier database application. 1.) MS SQL DB 2.) Middle tier SOAP Server (with Delphi 7) connected to the DB 3.) Clients (first win32 gui (with Delphi 7) - later other platfomrs) connected to the SOAP server I chose a SOAP Server to be open to various clients at a later stage (also some of the win32 gui clients will be stationed abroad - so the clients need to be thin) (this as suggested by Dr. Bob). I am new to SOAP and have been looking at different examples and papers about authentication. But cant quite get my head around it. I have made a SOAP server and client with Delphi's SOAP Server Application Wizard and added a SOAP SERVER Data Module, added a database connection and some datasets and providers. Connected the client with dbgrid etc and that part works fine. But I want the client first to login and then be able to access data and I want the server to log each connection and also when the client logs off or is disconnected, so I am guessing I need the sessionID and a timeout. I also want the server to be able to tell the clients who else is "connected" (or whos session is still active) at any given time. I have gathered that I need to make a authentication header, but cant figure out where or who I can get a sessionID. I presume that each time a client connectes to the server the server generates a sessionID? How do I get this? Any help or suggestions/pointer would be appreciated, thanks Justin OK take 2: OK, I have done the following so far (this is used from the example Bank Account SOAP application that comes with Delphi 7): procedure TForm1.btnLoginClick(Sender: TObject); var H: TAuthHeader; Headers: ISOAPHeaders; SoapData: IThorPayServerDB; begin SoapData := HTTPRIOOnForm as IThorPayServerDB; if not(SoapData.login(edtUser.Text,edtPassword.Text)) then begin showmessage('Not correct login'); exit; end; Headers := SoapData as ISoapHeaders; { Get the header from the incoming message } Headers.Get(TAuthHeader, TSoapHeader(H)); try if H < nil then begin FIdKey := H.IdNumber; FTimeStamp := H.TimeStamp; end else ShowMessage('No authentication header received from server'); finally H.Free; end; if FIdKey 0 then showmessage('Authenticated');; end; The SoapData.login returns the correct result, but for some reason I cant get hold of the header. In this case H is nil and the result becomes 'No authentication header received from server'. If I intersept the SOAP xml I can see that the header is there, here is the returned package: 1 1 4208687 2010-05-14T10:03:49.469+03:00 true Anyone any idea? In this case I am not using the SOAPConnetion that I am using for the DB, but a seperate HTTPTRIO component.

  Read the article

< Previous Page | 310 311 312 313 314 315 316 317 318 319 320 321  | Next Page >