Search Results

Search found 11093 results on 444 pages for 'issues'.

Page 315/444 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• XP Client for NFS failure dialog on startup, but drive mapping works

  - by Matt Bennett

  I'm mounting an NFS share to some windows machines using the tools that come in the Services for UNIX Administration toolkit. I've set up the User Name Mapping service to use local passwd and group files. I had to manually start the User Name Mapping service, and then created an 'advanced map' from the XP machine's user to a uid that exists in on my NFS server, like so: Windows User: Matt Bennett UNIX Domain: PCNFS UNIX User: mattbennett UID: 10250 Primary: * I can map a network drive without any issues, and it correctly identifies the UID and GID to use, but when I reboot I get this message: "An error occurred while connecting to the NFS server. Make sure that the Client for NFS service has started. If the problem persists make sure Client for NFS service can communicate with User Name Mapping or PCNFS server." After dismissing the dialog, the machine finishes booting and the network drive is there in My Computer with the title "Disconnected Network Drive", but I can open it I can see the network share without a problem, and then it drops the 'disconnected' from its title. It seems like the services are starting in the wrong order or something, so the first attempt to connect fails but subsequent ones work as expected. There don't seem to be any symptoms apart from the dialog box, but obviously something's not quite right. What have I done wrong? Thanks, Matt.

  Read the article

• PC only boots from Linux-based media and won't boot from DOS-based media

  - by xolstice

  I have this problem where the PC only seems to boot from a floppy disk or CD if it was created as a Linux-based bootable media. If it was created as a DOS-based bootable media the system just freezes at the starting point of the boot process. I originally asked this under question 139515 for CD booting only, and based on the given answers, I was under the impression the problem was with the CD-ROM drive; however, I have since installed a newly purchased CD-ROM drive and the same freezing occurs. This then made me try the DOS bootable floppy disk approach and I was quite surprised that it exhibited the same freezing problem. I then tried try a Linux bootable floppy and everything booted from it without any issues. As I mentioned in my original question, the PC was booting just fine from the DOS-based bootable CD, and then it suddenly decides to pull this freezing stunt. I can't remember if I changed anything in the BIOS settings that may I have caused the problem, but I am wondering if that could be the case - it is currently using the Award Module BIOS v4.60PGMA. Can anyone help?

  Read the article

• Why can't this user connect to domain share?

  - by Saariko

  Part of my reorganizing credentials in the domain, I have created several users that will be used solely for services (backup, LDAP, etc) The idea is that systems that need specific usage will use a user/service user, that will give them what they need. However, I am having trouble setting the correct needed data. For this example, I have a NAS (Ready NAS 1100 by Netgear), that runs it's own backup jobs. The job reads from a domain share: \domain\qa and copies all data to another location. When using the domain\administrator everything works. When I input the domain\srv.backup user I get an error connecting to the folder. The srv.backup is part of the 'Domain Admins' group, which is a member of 'Administrators' I thought there might be propagation issues, but even when the srv.backup user was a direct member of 'Administrators' the error still occurred. I have 2 DC's (W2K8R2 replicas) - I thought that could also cause a problem, AFAIKT it's not the issue. Sharing permissions are open to everyone The Security on the folder is as follow This is the test window from the NAS dashboard I doubled check that the 'srv.domain' is part of the 'Domain Admins' group As well as tried with a simple 1-9 password. What else do I need to check? thanks.

  Read the article

• Adobe Reader Wants Sensitive Email Details

  - by KDM

  When I run Adobe Reader, it tells me: Either there is no default mail client or the current mail client cannot fulfill the messaging request. Please run Microsoft Outlook and set it as the default mail client. I have a couple of issues with this: 1) It presupposes everyone has Microsoft Office installed. Not all home users have the budget or inclination for this. 2) It presupposes everyone wants Microsoft Outlook to be their default mail client. 3) I have Microsoft Office (incl. Outlook) installed and set as my default mail client. Even if I make it the default mail client from within the Adobe Reader Preferences, that doesn't stop the dialog appearing. 4) I thought I'd give Adobe Reader a new email address in the preferences, just to get it to stop bugging me. I notice, though, that it want's the SMTP and POP addresses and the account password? They have got to be kidding? I just want to view PDF files. How do I get the message to go away without telling Adobe my life story, giving them my mother's maiden name, my favourite movie, my place of birth, the name of my first goldfish and emptying the contents of my wallet for them?

  Read the article

• Does Windows 7 Authenticate Cached Credentials on Startup

  - by Farray

  Problem I have a Windows domain user account that gets automatically locked-out semi-regularly. Troubleshooting Thus Far The only rule on the domain that should automatically lock an account is too many failed login attempts. I do not think anyone nefarious is trying to access my account. The problem started occurring after changing my password so I think it's a stored credential problem. Further to that, in the Event Viewer's System log I found Warnings from Security-Kerberos that says: The password stored in Credential Manager is invalid. This might be caused by the user changing the password from this computer or a different computer. To resolve this error, open Credential Manager in Control Panel, and reenter the password for the credential mydomain\myuser. I checked the Credential Manager and all it has are a few TERMSRV/servername credentials stored by Remote Desktop. I know which stored credential was incorrect, but it was stored for Remote Desktop access to a specific machine and was not being used (at least not by me) at the time of the warnings. The Security-Kerberos warning appears when the system was starting up (after a Windows Update reboot) and also appeared earlier this morning when nobody was logged into the machine. Clarification after SnOrfus answer: There was 1 set of invalid credentials that was stored for a terminal server. The rest of the credentials are known to be valid (used often & recently without issues). I logged on to the domain this morning without issue. I then ran windows update which rebooted the computer. After the restart, I couldn't log in (due to account being locked out). After unlocking & logging on to the domain, I checked Event Viewer which showed a problem with credentials after restarting. Since the only stored credentials (according to Credential Manager) are for terminal servers, why would there be a Credential problem on restart when remote desktop was not being used? Question Does anyone know if Windows 7 "randomly" checks the authentication of cached credentials?

  Read the article

• Development on Windows 7; Web server on Linux - How to share Apache web root?

  - by TheKeys

  I've got a LAMP server that I want to use as a local web server. I've got a Windows 7 machine that I want to use as my development machine. The machines will be on the same LAN (or the Windows box will be VPNed into the LAN). My questions is, what is the best way of sharing the web root of the LAMP server so that I can edit the files on the remote Windows 7 machine and how do I go about configuring this on the Linux machine? (Fedora 16) I would like the solution to be as easy to use as possible with preferably no extra steps required to save/edit/upload files from my IDE on my Windows 7 machine. I'm thinking either a Samba or NFS share are the way to go but I'm concerned I'm going to run into issues with permissions and unix/windows file handling. Is one better than ther other for my use case or is there a better alternative solution? I'm currently using Windows 7 Professional which doesn't have NFS support but would upgrade to Ultimate which does have NFS support if it's the best solution.

  Read the article

• InstallShield or Windows installer corrupted

  - by Bobby S

  Just recently I've been unable to install any software on my Windows 7 machine. Anything that uses InstallShield or the Windows installer will just hang or give a weird error. I noticed there will be many duplicate isbew64.exe processes (like 25) that launch and then just sit there or else a lot of msiexec.exe *32 processes, depending on what I'm trying to install. One piece of software specifically is the Logitech Harmony software. It gives me an *is_string_not_defined* error, saying c:\program files (x86)\:\ the filename, directory name, or volume label syntax is incorrect. The other thing I was trying to install was Battlefield: Bad Company 2, and that just hangs as well, and then just leaves all the Windows installer processes running in the background after I quit the install process. Very odd. I've checked well and googled these issues, it doesn't appear to be any sort of malware issue. I feel like it's related to some kind of corrupted installer application. I've rebooted, deleted the InstallShield folder in program files/common files as some places online suggested but to no avail. I have no idea what to do, any ideas?

  Read the article

• How to setup an IPSec / GRE tunnel on Windows Server 2008

  - by qbeuek

  I have a Windows Server 2008 that has a single network interface configured with a public IP address. My business partner has a private network. From my server, I need to access all the devices on his private network, and those devices must be able to access my server. My business partner has a standard solution for these requirements. They will setup an IPSec + GRE tunnel to my server. They told me, that I will need an additional public IP address for this to work. If it really is necessary, there is no problem, I can get an additional public IP address, although it will be assigned to the same physical network interface. I assume that on my server I will have both public IP addresses and also the private IP address from the tunnel (the same that is visible for the devices inside the private network). What alternatives do I have? Is it possible to configure this tunnel on my Windows Server 2008? Can it be done using only Windows tools, or do I need an additional free / commercial VPN software? If it cannot be done directly on Windows, can I setup an additional virtual machine running Linux, that will handle the IPSec + GRE tasks? How to do it? If it cannot be done on a virtual linux box, will I have to buy and setup a Cisco router to handle the IPSec + GRE tasks? Thanks for your opinions. I'm watching this question to clarify any issues or questions.

  Read the article

• Sharepoint Workflow "Failed on Start" only when powershell import script is called from task scheduler

  - by Matt Keller

  I created a simple PowerShell script that takes an XML file in a local directory on our sharepoint server and imports it into a specific SharePoint form library. (Content management enabled library if that makes any difference) This script works flawlessly if i run it from the PowerShell command line manually. I call it like such: ".\script_name.ps1". It completes without error and the item is imported into the form library successfully. The workflow begins on the item and everything is happy dandy. However, i run into issues when i setup a scheduled task using Windows Server 2008 R2's task manager. The task runs the script without error and it does actually import the XML into the form library. I looks perfectly normal just as if i had run the script manually. However, after about 10 or 20 minutes the workflow status for that item changes from "In progress" to "Failed on Start (Retrying)". The scheduled task in question is a basic task and has only one action. (Start a program) The "program/script" box is set to "C:\Windows\System32\WindowsPowerShell\v1.0\powershell.exe" and the "Add arguments" box is set to the path of the actual ps1 script. (C:\scripts\sharepoint_import.ps1) I've tried running the task as various users. I've also tried with and without the "Run with highest privileges" check box. Nothing seems to work. For reference, here is the script i am using to import items into the form library.

  Read the article

• VNC failure on Xen

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Using npm install as a MS-Windows system account

  - by Guss

  I have a node application running on Windows, which I want to be able to update automatically. When I run npm install -d as the Administrator account - it works fine, but when I try to run it through my automation software (that is running as local system), I get errors when I try to install a private module from a private git repository: npm ERR! git clone [email protected]:team/repository.git fatal: Could not change back to 'C:/Windows/system32/config/systemprofile/AppData/Roaming/npm-cache/_git-remotes/git-bitbucket-org-team-repository-git-06356f5b': No such file or directory npm ERR! Error: Command failed: fatal: Could not change back to 'C:/Windows/system32/config/systemprofile/AppData/Roaming/npm-cache/_git-remotes/git-bitbucket-org-team-repository-git-06356f5b': No such file or directory npm ERR! npm ERR! at ChildProcess.exithandler (child_process.js:637:15) npm ERR! at ChildProcess.EventEmitter.emit (events.js:98:17) npm ERR! at maybeClose (child_process.js:735:16) npm ERR! at Socket.<anonymous> (child_process.js:948:11) npm ERR! at Socket.EventEmitter.emit (events.js:95:17) npm ERR! at Pipe.close (net.js:451:12) npm ERR! If you need help, you may report this log at: npm ERR! <http://github.com/isaacs/npm/issues> npm ERR! or email it to: npm ERR! <[email protected]> npm ERR! System Windows_NT 6.1.7601 npm ERR! command "C:\\Program Files\\nodejs\\\\node.exe" "C:\\Program Files\\nodejs\\node_modules\\npm\\bin\\npm-cli.js" "install" "-d" npm ERR! cwd D:\nodeapp npm ERR! node -v v0.10.8 npm ERR! npm -v 1.2.23 npm ERR! code 128 Just running git clone using the same system works fine. Any ideas?

  Read the article

• Format & Fresh Install Mac OS X Snow Leopard on Mac mini.

  - by sagar

  Hello Every one. I have purchased a DVD of Snow Leopard (Mac OS X 10.6.2) I purchased a Mac mini with Leopard (Mac OS X 10.5.7) I tried to install Mac OS X 10.6.2 Everything went perfectly. System was installed successfully. But the problem that I faced is as follows. System was installed but my older data remained as it is. (means installation didn't format every thing - means installation was done on upgrade basis.) Now, my system works with very low speed. Previous performance of Mac mini was double as compare to current upgrade version. Now - my question are as follows. Does an upgrade installation causes the performance issues in Mac OS X? Or is Snow Leopard too demanding for the Mac mini? ( 2 Ghz Intel Core 2 Duo, 1GB RAM - is this configuration OK for Snow Leopard? ) Does a fresh install work better than an upgrade?

  Read the article

• Why are group policy preference drive mappings not applied to the domain administrator account?

  - by Saariko

  I have a working policy on my entire domain. I just found out, when logging with the domain administrator, that this policy is not applied (EDIT: Running : gpresult shows that the GPO's are applied - but, this GPO is for Drive Mappings, and the actual drive mappings are NOT shown) The administrator account - does not have any login script on his profile tab. To note: The mappings were applied before the GPO with a login script using the : net use ... command - all was working perfectly and correctly for the domain administrator user as well - That removes sharing and security problem (IMO) My GPO's are mainly small/atomic settings: single GPO to handle each settings: UAC, Firewall, printers. GPO status for the object is enabled That's an overview of the Drive Maps: Reading on MS support site, I checked the delegation tab, and it is marked as applied to domain and enterprise admins. Every user gets these policies correctly. The OU that is set is the root of the domain. (for testing purpose - I did that to eliminate hierarchy issues - did not help) Block Inheritance is disabled. (never used it anyway) GPO link GPO Security Filterings

  Read the article

• Sharepoint/WSS Reporting Services Integration woes

  - by mhollers

  after a number of failed attempts i seem to have successfully installed the Reporting services add-in to my WSS farm. However, I seem to be missing most of the enhanced functionality eg no report library template, no report center site template. the only additional functionality available is the report viewer web part. background: 2 server WSS 3.0 farm with CA (Central admin) WFE (web front end) and reporting services addin installed on 1, and SQL05 SP2 with Reporting services (RS) and all databases installed on other. I have a VM environment set up and have rolled this back and repeated a number of times. I have configured RS within CA and activated 'Report Server INtegration Feature'. Within the 'site settings' I have a 'Reporting Services' heading with a 'manage shared schedules' item/link, not sure if there should be other options? I was of the understanding that to view reports within sharepoint i could either create a new site using the 'report center' template or add a report library to an existing site, neither of which seems available I am at a loss as to what to do, as all online information seems to do with dealing with installation issues/errors, which i seem to have eventually got past

  Read the article

• windows Home Server backup error

  - by domen

  I've finally built my WHS, but some other problems have showed up. I've googled, binged and searched SU with no success. The problem is following: at the moment I've got a Win7 laptop and Win7 PC, which should be backed up by the WHS. Laptop is backed up just fine with no issues, but when I try to manually backup the PC, after "backup is starting" message, when backup service should be monitoring changes on partitions, PC gets disconnected from the home network and thus, the backup process is stuck. Disabling/enabling network adapter gets PC back on the network. The only thing I've tried was reinstalling connector software. no success. Also, I've downloaded connector troubleshooter and only thing it says is "DHCP server was not found". I'm not good with networks, so I couldn't figure out what could that indicate (all computers in the network are assigned static IPs). Any ideas what the problem can be? I can provide any additional information, I'm just not sure what may be helpful right now. Thanks.

  Read the article

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• How to Programmatically Split Data Using VBA Using Specific Logic

  - by Charlene

  This is an addition to my previous post here. The code that was previously supplied to me worked like a charm, but I am having issues modifying it adding some additional logic. I am creating a macro in VBA to do the following. I have raw order data that I need to transform based on some logic. Raw Data: order-id product-num date buyer-name prod-name qty-purc sales-tax freight order-st 0000000000-00 10000000000000 5/29/2014 John Doe Product 0 1 1.00 1.50 GA 0000000000-00 10000000000001 5/29/2014 John Doe Product 1 2 1.00 1.50 GA 0000000000-00 10000000000002 5/29/2014 John Doe Product 2 1 1.00 2.00 GA 0000000000-01 10000000000002 5/30/2014 Jane Doe Product 2 1 0.00 0.00 PA 0000000000-01 10000000000003 5/30/2014 Jane Doe Product 3 1 0.00 0.00 PA Desired Outcome: HDR 0000000000-00 John Doe 5/29/2014 CHG Tax 3.00 CHG Freight 5.00 ITM 10000000000000 Product 0 1 ITM 10000000000001 Product 1 2 ITM 10000000000002 Product 2 1 HDR 0000000000-01 Jane Doe 5/30/2014 ITM 10000000000002 Product 2 1 ITM 10000000000003 Product 3 1 The "CHG" rows are created based on the following logic; if the order-st is CA or GA, add the total of sales-tax and freight for each of the rows with the same order-id. If the order-st is NOT CA or GA, no CHG rows should be created. Any help would be appreciated - let me know if I left any details out!

  Read the article

• Sniffing at work- How to detect

  - by coffeeaddict

  Because of the place I work has some real issues (people) especially in IT and the owner, I wonder if we are being sniffed. Is there any way to tell if on a Vista 64-bit machine: 1) In system logs some identification that would tell me that someone might log into my PC such as an Admin 2) Something in the logs that would give me a flag about maybe I'm being monitored some other way? 3) How can I be sure that my gmail, hotmail, and chat is not being sniffed. I know there are things like Simp, etc. I'm talking about specific hidden system signs either in registry or logs. Obviously I'm not going to raise any suspicion by me asking our network admin. I don't trust anyone at this company. is there a good way to basically monitor for this as an end user? Could someone log in and basically watch me work and if so, would there be any goodies left behind for me to find out if this has happened other than visual signs which would not be present...maybe some running processes?

  Read the article

• CouchDB Errors: "undefined symbol: js_fgets" on Ubuntu 10.04

  - by MattEzell

  Hello, ServerFault Community. I have been wrestling with this problem for weeks without resolution and was hoping that someone here might be able to help. As indicated above, this is in Ubuntu 10.04 (x86) using CouchDB 0.11.0. I have build and installed CouchDB 0.11.0 from source. Everything with the dependencies and with the CouchDB install itself 'goes off without a hitch' - no errors or complaints in the configure, make or install... CouchDB seems to be running 'fine'. I can access Futon without issue and utilize all CouchDB functionality found in Futon... Unfortunately, when I attempt to use any shows/views for an installed Couch App, I get the above js_fgets error before terminal (and the Couch log) fills up with TONS of JSON. Nothing ever renders in the browser, though Firebugs reports. I have used the official instructions (paying special attention to the 10.04 instructions) and have followed pretty much every Google thread that I can find on similar issues. I have chase SpiderMonkey (and Rhino) as well as Erlang as the culprit, but despite reinstalls and tests with these components, I still cannot get past this CouchDB issue on my system... Ideas? Pointers? Suggestions? Has anyone successfully installed and used CouchDB 0.11.0 on an Ubuntu 10.04 system to RUN APPLICATIONS? I have come across multiple individuals who immediately respond 'yes, I have it installed - it works great' only to have them realize in the end (as I did) that just because Futon thinks things are working, doesn't mean CouchDB is properly handling ALL requests. Thank you for your time and assistance!

  Read the article

• Suggestions for Windows 8 migration [closed]

  - by Big Endian

  I'm thinking of migrating to Windows 8. At first I hated it, but I'm pretty sure the Windows 8 model is the future, and I don't particularly want to end up hating the future like my parents, frustrated and bewildered by anything past Windows XP. I'm currently running Windows 7 and my system has been accumulating some problems. It's probably an accumulation of issues from installing too much software, changing firewall settings, installing Ubuntu alongside Windows, and... well I'm not sure, but my computer has been buggy in unexpected ways lately (freezing and unfreezing, display driver crashing and recovering, and what I call "deep freeze/thaw cycle" where the mouse won't even move for a while). I'm good at solving computer problems, but I can't seem to get to the root of these and my best idea for fixing them is making sure I've backed up every file then re-installing the entire OS. Luckily for me, a new OS is just around the corner so this would be a good time to get two things out of the way at once. The problem I see is that the upgrade options I see are all "seamless". I don't want a seamless upgrade. I want to wipe the slate clean and start all over. Does this mean I will have to buy a full, new copy of Windows 8 rather than one of the cheaper upgrading options? Or does it not make since for me to go to Windows 8 given that I have a laptop, not a tablet? Maybe I should just re-install Windows 7, or even call good enough good enough, try to eliminate the bugs, and start with a fresh slate in 2-3 years after this computer eventually dies entirely from (inevitable) hardware failure. What would be the advantages or disadvantages and costs of each option, how would I go about upgrading to Windows 8 if that's the option I choose, and what is your personal opinion about my situation?

  Read the article

• ColdFusion 9 server not restaring - “Permission denied” errors

  - by Xevi Pujol

  I had to restart my ColdFusion 9 server on CentOS because of a memory performance issue, but now the server won't restart again. When looking at cfserver.log I can see how there's "Permission denied" errors all along. The ColdFusion application folder (/opt/coldfusion9/) is owned by nobody:root, as that fixed a similar problem that we had a few weeks ago. Also, the last time this CF server was running correctly, the JRE user that was being used was nobody. Maybe CF is trying to restart using another user (presumably apache) and that creates permission issues? However, I'm not sure how to check this hypothesis. Where's the config file that tells CF what JRE user to utilize? If I can change that, I could try to specify nobody there. Any other ideas also welcome. UPDATE: The runtime user that Coldfusion will utilise is defined in /etc/init.d/coldfusion_9. I fixed the problem by being consistent with the users: I needed to revert the ownership of the folder /opt/coldfusion9/ back to apache:root, which matches the init file.

  Read the article

• How to diagnose a hang when creating a new folder in explorer.exe

  - by Jack Ukleja

  I have been having some issues with explorer.exe hanging when I create a new folder. If I use Analyse Wait Chain in the Resource Monitor it says "One or more threads of explorer.exe are waiting to finish network I/O". When I look at the offending thread in Process Explorer it reveals nothing interesting: ntdll.dll!ZwWaitForMultipleObjects+0xa KERNELBASE.dll!GetCurrentThread+0x36 kernel32.dll!WaitForMultipleObjectsEx+0xb3 USER32.dll!PeekMessageW+0x1cd USER32.dll!MsgWaitForMultipleObjectsEx+0x2a USER32.dll!MsgWaitForMultipleObjects+0x20 SHELL32.dll!SHAppBarMessage+0x41e SHELL32.dll!DragAcceptFiles+0x2a3c SHELL32.dll!DragAcceptFiles+0x2a4f SHELL32.dll!Ordinal211+0x124 SHELL32.dll!SHChangeNotification_Unlock+0x12f4 USER32.dll!GetSystemMetrics+0x2b1 USER32.dll!IsDialogMessageW+0x19b USER32.dll!IsDialogMessageW+0x1e1 ntdll.dll!KiUserCallbackDispatcher+0x1f USER32.dll!PeekMessageW+0xba USER32.dll!PeekMessageW+0x89 SHELL32.dll!SHChangeNotification_Unlock+0xd9f SHELL32.dll!Ordinal885+0x1407 SHLWAPI.dll!SHRegGetUSValueW+0x306 kernel32.dll!BaseThreadInitThunk+0xd ntdll.dll!RtlUserThreadStart+0x21 While I was looking at the explorer.exe threads I did notice a fair few that talk about ETW (Event Tracing for Windows) so obviously explorer.exe uses tracing. So I decided to try and user TraceView.exe to try and listen in on the explorer.exe traces. The problem is TraceView requires some difficult-to-come-by stuff... either pdbs, or CTL files, and .TMF files. I tried using the explorer.pdb that comes with the Windows SDK but that did not work. I do not see explorer.exe in the "named providers". And I have no idea where to locate the ctl or .TMF files for explorer.exe. So the question is: Is there a way to view the ETW trace messages from explorer? Or shall I just not bother and go back to the age old technique of disabling every explorer extenion one-by-one in the hope its one of them. (Prefer the former as I like to get to the bottom of things!!)

  Read the article

• Does AMD Cool n Quiet Slow Down Your System?

  - by Software Monkey

  I discovered today that having AMD Cool n Quiet enabled in my BIOS appears to be slowing down my Windows XP SP2 system by about 29% on memory & CPU intensive workloads. I was wondering if (a) anyone else had encountered this, (b) anyone can offer an explanation, (c) there are any negatives I need to be aware of if I keep AMD CnQ disabled. With some superficial testing so far, I don't immediately notice any difference with CnQ off (other than the performance being what I expected from this new hardware). It seems to ramp up the CPU fan a little bit as my program maxes out 1 core, but that's the same as with CnQ on. And when I let the system idle the CPU fan slows down and the systems as quiet as a mouse (after years of 6 small fans churning like they want to go into orbit it's nice to again have a system where I can hear the HDDs seeking). Bonus question: Does CnQ cause issues with system stability? I ask because the reason I disabled it was because I have had a few freezes and 1 spontaneous reboot with my new hardware.

  Read the article

• Selective Pointer device remapping in linux

  - by user6368

  I just got an HP 2710p (hp tablet, with digitizer), and I've played around with linux for a while now, and thought I would go ahead and install it. Everything works fine, excepting normal tablet functions, which is to be expected. I'm working on the screen rotation, and there are on-screen keyboards, etc, but I'm having issues with the stylus. I can tap and left click with the stylus as normal, but the side button (which in windows functions as a right mouse button) appears as a 'button 2' to xev (a middle/scroll wheel button). I can switch 'button 2' and 'button 3' universally using xmodmap, but I'd like to do so exclusively for stylus so I don't screw up regular pointing devices. Altering xorg.conf (which is surprisingly bare) with the recommended sections (adding sections for each of the stylus buttons) does nothing. I'm running crunchbang, which is an ubuntu/debian varient with openbox as the windows manager. Thanks Also, as a seperate note, does anybody know how to detect when I rotate and/or latch the lid shut? I was thinking maybe I could run a script to switch the buttons when I close it, but I can't find any information.

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >