Search Results

Search found 9122 results on 365 pages for 'sound card'.

Page 315/365 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• Overscan in Catalyst Control Center

  - by alex

  I've connected my PC to my TV via HDMI (I've also tried using DVI). Whatever the resolution (anything from 800 x 600 to 1080p), the image displayed on the TV does not fill the entire screen surface; there's a black border on the edge of the image. This happens in both Vista and Windows 7. After a bit of searching I came to the conclusion it's got something to do with overscan done by the graphics card (ATI 3200HD). It's definitely not the TV because on my old PC there were no such problems. I've searched for the option in Catalyst Control Center 9.9 but it's not available for the TV; if I connect a normal LCD display, the option is there, but only for the LCD screen. If I choose Configure for my TV, where the overscan option should be, it takes me to the Welcome tab in CCC. How can I make the image fill the entire screen? How can I enable/disable overscan for my TV?

  Read the article

• Interruptionless Uploads / Rollback in IIS

  - by NickatUship

  I'm not sure if this is the right way to ask this question, but here's basically what i'd like to do: 1.) Push a changeset to a site in IIS. 2.) Don't interrupt the users. 3.) Be able to roll back effortlessly. So, there are a few things that I know have to happen: 1.) Out of Proc session - handled 2.) Out of Proc cache - handled So the questions that remain: 1.) How do i keep from interrupting the users? If i just upload the files to bin, the app recycles and takes 10+ seconds to come back online 2.) How do i roll back effortlessly? I was thinking a possible solution would be to have two sites set up in IIS, one public and one private. Uploads go to private and get warmed up. After warmup, the sites are swapped. A rollback only entails swapping to private without an upload. This seems sound in theory, but Im not sure of the mechanics. Any ideas?

  Read the article

• Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

  - by Paul Taylor

  I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

  Read the article

• Is this hard disk dead?

  - by Korjavin Ivan

  Not sure, is this right site for this Q, but let me try Last time i have problem with hard disk. Sometimes its do strange sound, and i get it from logs: $dmesg | grep ata4 [29409.945516] ata4.00: exception Emask 0x10 SAct 0xf SErr 0x90202 action 0xe frozen [29409.945529] ata4.00: irq_stat 0x00400000, PHY RDY changed [29409.945538] ata4: SError: { RecovComm Persist PHYRdyChg 10B8B } [29409.945546] ata4.00: failed command: READ FPDMA QUEUED [29409.945562] ata4.00: cmd 60/30:00:56:22:5f/00:00:00:00:00/40 tag 0 ncq 24576 in [29409.945573] ata4.00: status: { DRDY } [29409.945580] ata4.00: failed command: READ FPDMA QUEUED [29409.945594] ata4.00: cmd 60/18:08:8e:22:5f/00:00:00:00:00/40 tag 1 ncq 12288 in [29409.945605] ata4.00: status: { DRDY } [29409.945611] ata4.00: failed command: READ FPDMA QUEUED [29409.945625] ata4.00: cmd 60/08:10:46:02:66/00:00:00:00:00/40 tag 2 ncq 4096 in [29409.945635] ata4.00: status: { DRDY } [29409.945641] ata4.00: failed command: READ FPDMA QUEUED [29409.945656] ata4.00: cmd 60/80:18:ee:04:66/00:00:00:00:00/40 tag 3 ncq 65536 in [29409.945666] ata4.00: status: { DRDY } [29409.945679] ata4: hard resetting link [29413.976083] ata4: softreset failed (device not ready) [29413.976097] ata4: applying SB600 PMP SRST workaround and retrying [29414.148070] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [29414.184986] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd [29414.243280] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd [29414.243292] ata4.00: configured for UDMA/133 [29414.243324] ata4: EH complete [680674.804563] ata4: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [680674.804575] ata4: irq_stat 0x00400000, PHY RDY changed [680674.804584] ata4: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [680674.804603] ata4: hard resetting link [680678.840561] ata4: softreset failed (device not ready) Is this ata4 sata hard drive dead? Must i change it ASAP ? Need I specify more info?

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• Google account gives ERR_SSL_BAD_RECORD_MAC_ALERT errors

  - by Kjensen

  A couple of days ago, I started being unable to connect to accounts.google.com, which handles logins to all kinds of google services. I get this error in Chrome: Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error. In IE I get this: I assume it is the same error, just wrapped up. I run Win8 RTM. On the SAME machine, using the same network card, in a VMWare workstation image running Win7, I am able to connect perfectly. On another of my machines on my network, I am also still able to connect with no problem. My girlfriend uses the same network and has also complained a couple of times about this error (google calendar) - but this is anecdotal, since her technical troubleshooting abilities stop at "xxxx is broken". Her machine runs Win7. ;) I have rebooted, cleared cookies, do not run any antivirus/firewall, have not changed network config. The first 3-4 days after installing Win8, I did not have any problems. I have also searched, and found a hint about enabling SSL2.0 in connection settings, which did not help. Anybody know something about this error and what I can do to fix it?

  Read the article

• Is there a realiable way to troubleshoot wake up from sleep in Windows?

  - by Borek

  Is there a reliable way to troubleshoot laptop wakes? I've seen "heuristics" posted here and there but isn't there really a simple and deterministic way to tell what's causing a problem? Specifically, my laptop wakes up about every hour for about 2 minutes. Exported event log entries are here: http://www.mediafire.com/?abcqb00v5wyo6pj. I've tried: powercfg -devicequery wake_armed Empty result set. Scheduled tasks - the main ones are not scheduled to run every hour. When go through a long list of all possible tasks, there are some that are set to be triggered every hour (e.g., MS "RacTask" whatever it is). But when I go to power options, Advanced settings, Sleep, Allow wake timers it is set to "Disable". Also, the specific task is not set to wake the computer if necessary. Power options for my Ethernet card don't enable it to wake the computer - the cable is disconnected anyway. There are no other HW devices attached - no USB disks, no keyboards / mice etc. I am really clueless and quite unhappy that it's so hard to troubleshoot this situation.

  Read the article

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• Windows 7 BSOD on startup

  - by Cristy

  I got a BSOD today after getting home from 11 hours of work... It seems to work in SAFE MODE (sometimes, not always) The BSOD says: SYSTEM_SERVICE_EXCEPTION STOP: 0x0000003b WimFsf.sys - Address FFFFF88001A6B76B base at FFFFF88001A600000, DateStamp 4a5bc362. Sometimes it shows the welcome screen, shows the destkop for a few seconds and then BSODs Already did: unplugged all the USB devices reset the CMOS I haven't installed any new software recently. What should I do? EDIT: I've managed to get into safe mode and it seems to works fine. When I go into normal mode it shows the desktop then it freezes... Is it more likely to be a software or hardware problem? EDIT2: I've managed to get into normal mode by disabling all the non-microsoft services & startup programs. One more thing: When I shut down my PC, on the "Logging off" screen appear some artifacts. I don't think it's because of my graphics card cause I've opened Black OPS and it worked fine. It's so strange... It still BSODS on startup (but there a ~=10% that it will not), and when it doesn't BSOD's it works fine...

  Read the article

• Is a Hyperthreaded CPU more powerful and more efficient than a Dual-core CPU? [closed]

  - by user1811864

  which computer to choose with Pentium processor hello they are getting rid of the old computer equipment in the office and i have to choose the computer to take home i get first choice to pick. -15 inch lcd screen 4 gb of ram core 2 duo dual Core E8400 3.00 GHz dvd writer windows vista/ linux -15 inch crt monitor with 2 gb ram and pentium 4 2 ghz single core HT technology windows xp hardisks both 250 GB my friend is telling me to choose the second one Pentium single core HT because he told me it runs faster becuase of HT technology and cooler and consumes less current electricity so it wont get overheated because it has HT technology so it's high definition for encoding and watching HD movies and HD sound and is like a gaming pc to play internet games. And also he said the dual core 8400 runs at 3 ghz compared to the 2 ghz so it heats very much because of the two extra cores so it takes more current raising electricty bills and is not good for gaming and watching HD movies and internet flash animations and games because of getting heated everytime. And he wants to choose and take the E8400 because he has air conditioning at home so it will be safe from heating. So which one computer should i take is it really faster because of the HT High definition technology and will i be able to play internet flash card games better and watch good HD movies Youtube etc and play all the music and songs.

  Read the article

• Looking for ballpark pricing on an affordable a Cisco VOIP solution for our office

  - by guytech

  We have about 8 incoming PSTN lines that are currently on an old and antiquated Nortel Meridian ICS system. This system has been giving us some grief. We're looking for a new VOIP solution. I've been looking at a Cisco solution and it does seem pricey but I'm sure effective. Unfortunately, we probably can't afford a Cisco Unified Communications 520 which seems to be the ideal solution. We have about 15 people who need an extension and voicemail. We really don't have any need for a fancy system just an auto attendant of some sort when people call us. It looks like we'll have to get an older router and an addon card for what we're looking for to get best value pricing. However, I don't know a a lot about Cisco voice products so I'm a bit lost as to what to get. The only thing I am sure on is the pricing on VOIP phones which we expect to be about ~$100-200. However, I'm not sure what pieces of VOIP infrastructure to get. Any advice? I am familiar with Asterisk but right now I'm looking on pricing concerning a Cisco solution.

  Read the article

• Is there a historical computer peripherals or accessories museum or even just a current list?

  - by zimmer62

  Thinking about all the unique and different peripherals I've owned over the years, from ISA capture cards, to parallel port controlled shutter glasses for 3d games. I've seen many many accessory or computer peripherals come and go. The nostalgia of these things is a lot of fun. I tried to find some sort of historical time-line or list but what mostly turned up is computers themselves. I'm more interested in the mice, scanners, the weird adapters that shouldn't exist, short run very rare products, strange devices from computer shows in the 80's and 90's... Hardware you might find in a geeks basement that would be completely useless now, but was the coolest thing around when it was new. An example would be a drawing tablet I had for my TI-99 computer, or the audio tape player accessory for a C64 which let you save files to audio tapes, An ISA card that did the same for PC's hooked up to a VCR. Remember that IBM-PC Jr upgrade kit, that added a floppy drive, more memory and the AT switch in the back? I'd love to find either a wiki, or a list that has already been assembled which contain many of these weird (or common) accessories. I've had so many over the years I suppose I could start a wiki here if such a list doesn't already exist.

  Read the article

• Windows is very slow with my new SSD

  - by Maksym H.

  I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

  Read the article

• openvpn problem

  - by Jared Voronik

  I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

  Read the article

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• Flow of packet in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

  Read the article

• How can I set up a touchscreen as the non-primary monitor in a dual monitor situation?

  - by bazzjedi

  I have been looking for information about using a second monitor, and thought of using a touchscreen. Will a touchscreen monitor work in a dual setup if it is not the main monitor? I haven't found any information on this; I've only found information about the touchscreen being the main monitor. That is, except at this SU question (snippet below): If you mean do the touch screen features still work on the other machine, the answer is yes. Past that, you can even see some of the touch screen features on a non touch screen monitor (just not the multi touch features!) For example, on the taskbar, click (without releasing) on any icon and then drag the mouse up, and you will see that it does the same as using your finger and dragging up. I have a HP 2510 for the main monitor. I'm thinking of adding a HP 2310ti (the touchscreen) as the secondary. My graphics card is a geforce gtx 295. I'm running Windows 7 Professional.

  Read the article

• How to record tv to network share with Windows Media Center?

  - by Peterdk

  Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

  Read the article

• Why can't I connect to my router's config page with Windows 7?

  - by user17940

  I've got a Belkin wireless router, and just bought a new Dell computer with Windows 7 pre-installed. I can connect to the Internet and my home network just fine, but when I try to visit my router's configuration page at http://192.168.2.1, I get a "Connection was reset" error. Nothing I do will make the router's configuration page come up in my web browser. More background information: I could always get to the router's config page from my Windows XP machine. I never had any trouble prior to getting this Windows 7 computer. I can ping 192.168.2.1 successfully from my Windows 7 computer. My PC is connected to the router by a physical CAT5 cable, not via wireless. Every device connected to my router, including the new computer, can get to the Internet with no problem. Here are some things that did not solve the problem: I tried turning off IPV6 in Windows. I tried turning off my firewall and antivirus software I tried using https instead of http I tried disabling and then enabling the network connection in Windows I tried reverting my network card driver back to an older version I have tried both Firefox and Internet Explorer web browsers. Has anyone experienced something like this before, and solved it? Thanks a lot for your help!

  Read the article

• How to run Fujitsu P27T-7 LED monitor in its not native resolution and have perfect fonts rendering

  - by Ilia Rostovtsev

  My problem is completely opposite to anything I could find as I need to run my monitor in its NOT native resolution and have perfect font rendering. I recently got myself Ultra HD 2560x1440 27 inch monitor (Fujitsu P27T-7 LED) and I have an issue with this. I would call it personal but I'm afraid it's not as few people already agreed with me. I do programming and the text on UHD is way to small for comfortable usage. I changed the resolution to regular Full HD (1920x1080), it became just right but the text is looking slightly blur now, in comparison to both its natural UHD resolution and/or to my old 23 inch NEC. I am pretty frustrated and not sure what to do and how to make fonts look just as sleek as they should? I can't work in UHD resolution (my vision is 100% perfect), simply if calculated, picture size with Ultra HD (2560x1440) on 27 inch is around 30% smaller than Full HD (1920x1080) on 23 inch. In order to have same font size, if compared with Full HD 23 inch, 27 inch Ultra HD monitor must be around 32 inches in size. If I set my new monitor to regular Full HD 1920x1080, then the fonts' size are just perfect but the quality is not as it's blurry? Could anyone please help me out with an advise of how to solve this problem? Spec: nVidia 560 Ti with DVI-D port on Fedora 20. EDIT 1: Changing fonts doesn't really help as everything else doesn't look the way it should. EDIT 2: The monitor is buzzing on 2560x1440 so badly in case there are lots of lines on the screen, like file listing. If I type ls /usr/bin it makes such nasty irritating sound. When resolution goes to 1920x1080 it's a bit better. Any idea why?

  Read the article

• Sudden and frequent hangs on desktop computer: mobo or CPU fault?

  - by djechelon

  I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

  Read the article

• Windows 7 starts getting sluggish over a few days

  - by munrobasher

  Myself and the other developer are running Windows 7 Enterprise 64 bit with 8GB RAM on different Gigabyte motherboards with Quad core Intel CPUs. Most of the time, it runs like a dream. We use VMware workstation a lot (hence the 8GB) and that works well. Except... now and then, after the PCs have been on for a few days, the whole system starts getting really sluggish doing certain tasks. The other's developer's system is far worse than mine with it taking up to a minute to launch IE. Today, mine has gone sluggish but nowhere near as bad. For example, normally when I click on a new tab in IE, it's instant. Today, there's an obvious delay. Right-clicking in this window to trigger iSpell is normally instant, right now it takes about five seconds. I've got resource monitor open on my second monitor and when I did that right-click, there was no obvious peak in CPU, disk or memory. A reboot does fix it so it does sound like a resource issue but haven't a clue what might be to blame. The two computers have similarities (same spec) but also differences (like motherboard, RAM & CPU models). So I guess the question is, any pointers on diagnosing why a PC is sluggish? What could cause such a right-click slow down in IE for example? It sounds like such a simple operation. NOTE: whilst typing this message alone, it was fine performance wise. I can click around the page no problem but right-click still is noticeable slow. Will reboot over lunch... Cheers, Rob.

  Read the article

• External Storage for 2TB of backups and 4TB of data RAID level? HW vs Software?

  - by Jerry Mayers

  I have a Mac Mini set up as a media center/file server. Currently I just have a hodgepodge mess of external drives for storage. I'm maxed out, and I have some new laptops on the way with much larger drives and I need to work out a good storage solution for backing them up, as well as storing media on the server. I need around 2 TB of storage for the time machine backups from my various systems and around 2 TB more for media. I would like to build this to handle around 6 TB total so I have some growing room. Since I'm using a Mac Mini as the server I need to use external enclosure(s) that support USB 2 or Firewire 800 (preferred) or gigabit Ethernet. Performance of the system isn't a huge concern since the majority of the access from other computers is done over 802.11N. I plan on using 2TB drives, for the final version, but initially I'll try and use my existing 2 (1TB) drives + some new 2TB drives, and swap the 1TB ones out as I fill up. As to the actual questions: Should I use hardware RAID in some enclosure? Because if the enclosure dies I have to find an identical one to get to my data right? Wouldn't a software RAID be better as I can use any method of connecting the drives to the system? Remember OS X server is my OS. What if I had to reinstall OS X, can I restore the software RAID easily? What RAID version should I use? For the 2TB used for the time machine disk I don't see why I need RAID here, just a single 2TB drive since its already the backup, but for the remaining 4TB it would be the only copy of the data so I should build some redundancy. I had a RAID 5 setup using a cheep RAID PCI card years ago running RAID 5 in a 2 TB array and when a drive died it wanted 48 hours to rebuild. Is this crazy slow for a setup of this size or is this to be expected? Any suggestions as to drive enclosures?

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >