Search Results

Search found 10169 results on 407 pages for 'port'.

Page 316/407 | < Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >

• RealTek RTL8188CE WiFi adapter doesn't connect reliably

  - by ken.ganong

  I recently bought a new system76 laptop which came pre-installed with Ubuntu 11.10. I've been having trouble with my wireless connectivity. It seems that my connection with my wireless network keeps going in and out. It is not my network--I have seen the same problem on multiple WiFi networks and at different distances and reported link qualities. OS version: Ubuntu 11.10 oneiric kernel version: 3.0.0-14-generic lspci: lspci -nnk | grep -iA2 net 04:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:9196] Kernel driver in use: rtl8192ce -- 05:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) Subsystem: CLEVO/KAPOK Computer Device [1558:2500] Kernel driver in use: jme iwconfig: iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"peppermintpatty" Mode:Managed Frequency:2.462 GHz Access Point: 98:FC:11:6C:E0:22 Bit Rate=72.2 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Power Management:off Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:1103 Missed beacon:0 lshw: sudo lshw -class network *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 00:1c:7b:a1:95:04 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.0.0-14-generic firmware=N/A ip=192.168.1.106 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:18 ioport:e000(size=256) memory:f7d00000-f7d03fff *-network description: Ethernet interface product: JMC250 PCI Express Gigabit Ethernet Controller vendor: JMicron Technology Corp. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 00:90:f5:c0:42:b3 size: 10Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:56 memory:f7c20000-f7c23fff ioport:d100(size=128) ioport:d000(size=256) memory:f7c10000-f7c1ffff memory:f7c00000-f7c0ffff Any help would be appreciated. The last time I've dealt with wireless issues, the most given solution was NDIS wrapper and I seem sorely out-of-date.

  Read the article

• Proxy settings do not promulgate to fat or thin clients

  - by solizin47

  I work in Hertfordshire schools, which use a proxy eg http://wf1.thegrid.org.uk on port 80 to allow graded access by all users, within the schools, to the Internet. I have Ubuntu 10.04LTS successfully running and I want to set up 12.04LTS to replace it. Many other replies to this question have answered questions about stand-alone computers and not addressed the LTSP server and its clients. I have come to a complete stop over the problem of the proxy server settings not promulgating over the local network to Ubuntu 12.04 thin or fat clients. When you input this setting (there are others for HTTPS and FTP) into the System Settings/Network Manager GUI on the server, then when a user logs into the server, both Firefox and Chrome can read the settings and will gain access to the Internet. HOWEVER, these settings are not promulgated to either thin or fat clients on the local network. Their System Settings/Network Manager GUI remains stubbornly blank. I have rebuilt the image after inputting the proxy settings, but it appears they are not part of the image. /etc/environment (on the server) already has: PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" http_proxy="http://wf1.thegrid.org.uk:80/" https_proxy="https://wf1.thegrid.org.uk:80/" ftp_proxy="ftp://proxy.intra.thegrid.org.uk:3128/" I have also tried this export http_proxy="http://wf1.thegrid.org.uk:80" export https_proxy="http://wf1.thegrid.org.uk:80" export ftp_proxy="http://proxy.intra.thegrid.org.uk:3128" within /etc/environment, and that had no effect, either. etc/apt/apt.conf also has: Acquire::http::proxy "http://wf1.thegrid.org.uk:80/"; Acquire::https::proxy "https://wf1.thegrid.org.uk:80/"; Acquire::ftp::proxy "ftp://proxy.intra.thegrid.org.uk:3128/"; The clients still have no proxy settings in their Network Manager, and no client user can access the Internet from Firefox or Chrome. Three questions: Why doesn't the “Apply system wide” button work? It does on 10.04, and every new user, and all existing users have access to the internet through the proxy without problem. How can I set up proxy settings that work for all the 12.04 clients? I noticed that if user West input the settings himself, they would follow him around the clients. However, this is not secure, because there are grades of settings which prevent visits to various sites, eg wf3 allows fewer sites than wf2 or wf1, so I can't allow users to input this setting themselves. Since the proxy setting followed the user around the clients, the setting must be somewhere in the user profile, since none of the other users have the proxy settings. Do you know where, and how I could fix the setting for users, or better, groups? The setting must then be unchangeable by the user, with no access to the Network Manager. If either 2. or 3. can't be done, then the Ubuntu 12.04LTS server is simply no use to us...

  Read the article

• Configure Jenkins and Tomcat using Puppet on Vagrant

  - by ex3v

  I'm playing with setting up my first Spring + jenkins + Tomcat CI dev environment. For now it's just a test/fun phase, but in the near future I'll be starting new project with my coworkers. That's the reason that I want development environment virtualized and exactly te same on every development machine, as well as on production server. I choosen to use Vagrant and to try to write puppet scripts that not only install everything, but also configure everything so each of us will have the same jenkins plugins, same jenkins and tomcat login and password, and literally after calling vagrant up we are ready to work. What I managed to do so far is installation of stuff needed and port forwarding. My vagrantfile looks like this (comments stripped): VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| config.vm.box = "precise32" config.vm.box_url = "http://files.vagrantup.com/precise32.box" config.vm.network :forwarded_port, guest: 80, host: 8090 config.vm.network :forwarded_port, guest: 8080, host: 8091 config.vm.network :private_network, ip: "192.168.33.10" config.vm.provision :puppet do |puppet| puppet.manifests_path = "puppet/" puppet.manifest_file = "default.pp" puppet.options = ['--verbose'] end end And this is my puppet file: Exec { path => [ "/bin/", "/sbin/" , "/usr/bin/", "/usr/sbin/" ] } class system-update { exec { 'apt-get update': command => 'apt-get update', } $sysPackages = [ "build-essential" ] package { $sysPackages: ensure => "installed", require => Exec['apt-get update'], } } class tomcat { package { "tomcat": ensure => present, require => Class["system-update"], } service { "tomcat": ensure => "running", require => Package["tomcat"], } } class jenkins { package { "jenkins": ensure => present, require => Class["system-update"], } service { "jenkins": ensure => "running", require => Package["jenkins"], } } include system-update include tomcat include jenkins Now, when I hit vagrant provision and go to http://localhost:8091/ I can see jenkins running, so above script works good. Next step is configurating jenkins and tomcat by extending above puppet scripts. I'm pretty green when it comes to CI. After wandering around web I've found few tutorials about jenkins configuration (here's one of them). I really want to move configuration presented in this tutorial to puppet file, so when I spread my vagrantfile and puppet file between my coworkers, I will be sure that everyone has exactly te same setup. Unfortunately I'm also green about using puppet, I don't know how to do this. Any help will be apreciated.

  Read the article

• Travelling MVP #2: Community event at Bucharest, Romania

  - by DigiMortal

  My second trip was to DevReach with two stops. My first stop was at Bucharest where I met with my friend Dimitar Georgiev who is one of authors of Gym Realm service. Romanian MVP Andrei Ignat was our host there and organized meeting with local community guys. With me – it was first time in my life – was one more guy from Estonia visiting DevReach and he made the whole trip with me. Bucharest We arrived to Bucharest 29.09 at night. We stayed at Hotel Michelangelo. It’s small hotel with nice rooms, free WiFi and very good service. Although my room was on the first floor there was no street noise. We visited one restaurant that offers national cuisine and it was really great. Next day we went out with local guys and had some beers in “old town”. Bucharest “old town” is nice and cozy. There are many bars open and I am sure everybody will find there some very okay place. After supper we visited one warm karaoke bar where we had beers with local guys. Andrei Ignat – karaoke star Agu Suur and Andrei Ion Rinea enjoying karaoke and tequila Community event Next day we had community event. I made my session about ASP.NET Web API and Dimitar told about how to port ASP.NET web applications to cloud environment. Sessions were held at study class of one local company. Dimitar Georgiev speaking about porting web apps to Windows Azure. As it was usual community evening and not some bigger event there were about 12 guys attending from Bucharest. There were both IT-PROs and developers and one nice thing about Bucharest community is that they are listening to you very well and they ask questions if something is unclear or if you slide over from topic they are interested in. Okay, we tried to keep up good tempo so people stay awake and I think we succeeded. After sessions we went all together to local Piranha pub that was near event venue. We had some beers with local guys and talked with them on different technology topics. It was another good and interesting evening at Bucharest. I want to go back there for sure. As it was my first trip to Bucharest and mostly I gathered experiences I think my next community trip there will be way stronger. I take it as a challenge. Plus – I have there some new friends and I want to meet them too – be it community event or not. :)

  Read the article

• How do I get wireless working on a Dell Inspiron 510m?

  - by user17449

  Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

  Read the article

• Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

  - by new_bie

  Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

  Read the article

• New Feature in ODI 11.1.1.6: Enterprise Data Quality Integration

  - by Julien Testut

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Oracle Data Integrator 11.1.1.6.0 introduces a new Open Tool called EnterpriseDataQuality which allows ODI users to invoke an Oracle Enterprise Data Quality Job from a Package. This post will give you an overview of this new feature. Oracle Enterprise Data Quality (OEDQ) provides organizations with an integrated suite of data quality tools that offer an end-to-end solution to measure, improve, and manage the quality of data from any domain, including customer and product data. The addition of the EnterpriseDataQuality Open Tool extends the inline Data Quality capabilities of Oracle Data Integrator with Oracle Enterprise Data Quality powerful data profiling, cleansing, matching, and monitoring capabilities. The EnterpriseDataQuality Open Tool can invoke any OEDQ Job stored in a Project. This Open Tool connects to an OEDQ server using a JMX (Java Management Extensions) interface. Once installed, this Open Tool will be found under Plugins in the Package Toolbox area: This EnterpriseDataQuality Open Tool takes a couple of parameters as inputs such as the Enterprise Data Quality Job and Project names, the OEDQ hostname and JMX port etc. With the EnterpriseDataQuality Open Tool, ODI customers can now incorporate their Oracle Enterprise Data Quality processes within their Data Integration workflows. You will find instructions about how to use the Enterprise Data Quality Open Tool in the Oracle Data Integrator documentation at: Using the EnterpriseDataQuality Open Tool.You can find an overview of all the new features introduced in ODI 11.1.1.6 in the following document: ODI 11.1.1.6 New Features Overview.

  Read the article

• Play a Webpage Display Prank in Google Chrome

  - by Asian Angel

  Are you looking for a fun but innocent prank to play on someone who loves using Google Chrome? If so then you may want to have a closer look at the Upside Down extension for Chrome. Before Here is our example webpage before starting the prank…looking all “normal like”. Upside Down in Action As soon as the extension has been installed you are ready to go. If you had a webpage open before installing the extension you will only need to refresh the page. As soon as the page has been refreshed or a new one is opened everything is going to look messed up very quickly. With the default setting there are five different “looks” available. To cycle through the five “looks” use the “Windows Key + Semicolon” or “Command + Semicolon” to toggle through them. On the sixth toggle the webpage will revert to normal (toggling afterwards starts the whole process again). Here are the five “looks” available…         Options There are options available for the extension where you can focus on just a specific effect or a group of effects. You can also enable a “Grayscale Effect” and even set a delay timer (a definite “evil touch”)! Think of the fun and surprised looks that await… Conclusion If you have been looking for a fun and unexpected prank for your favorite Google Chrome fan then this just might be what you have been looking for. Get ready to sit back and watch the fun. Links Download the Upside Down extension (Google Chrome Extensions) Similar Articles Productive Geek Tips Take Screenshots of Any Webpage in Google ChromeHow to Make Google Chrome Your Default BrowserSubscribe to RSS Feeds in Chrome with a Single ClickActivate the Redesigned New-Tab Interface in Google ChromeFriday Fun: Play MineSweeper in Google Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 If Web Browsers Were Modes of Transportation Google Translate (for animals) Out of 100 Tweeters Roadkill’s Scan Port scans for open ports Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows

  Read the article

• Time passage arithmetic explanation

  - by Cyber Axe

  I ported this from http://www.effectgames.com/effect/article.psp.html/joe/Old_School_Color_Cycling_with_HTML5 some time ago. However i'm now wanting to modify it for the purpose of changing it from floating point to fixed point maths for enhanced efficiency (for those who are going to talk about premature optimization and what not, i want to have my entire engine in fixed point both as a learning process for me and so i can port code more easily to systems in the future that dont have native floating points such as arm cpus) My initial conversion to fixed points just resulted in the cycling stuck on either the first or last frame of cycling. Plus it would be nice to understand better how it works so i can add more options and so forth in the future, my maths however sucks and the comments are limited so i don't really know how the maths work for determining the frame it shoud use (cycleAmount) I was also a beginner when i ported it as i had no idea between floating points and integers and what not. So in summary my question is, can anyone give an explination of the arithmatic used for determining the cycleAmount (which determings the "frame" of the cycle) This is the working floating point maths version of the code: public final void cycle(Colour[] sourceColours, double timeNow, double speedAdjust) { // Cycle all animated colour ranges in palette based on timestamp. sourceColours = sourceColours.clone(); int cycleSize; double cycleRate; double cycleAmount; Cycle cycle; for (int i = 0, len = cycles.length; i < len; ++i) { cycle = cycles[i]; cycleSize = (cycle.HIGH - cycle.LOW) + 1; cycleRate = cycle.RATE / (int) (CYCLE_SPEED / speedAdjust); cycleAmount = 0; if (cycle.REVERSE < 3) { // Standard Cycle cycleAmount = DFLOAT_MOD((timeNow / (1000 / cycleRate)), cycleSize); if (cycle.REVERSE < 1) { cycleAmount = cycleSize - cycleAmount; // If below 1 make sure its not reversed. } } else if (cycle.REVERSE == 3) { // Ping-Pong cycleAmount = DFLOAT_MOD((timeNow / (1000 / cycleRate)), cycleSize << 1); if (cycleAmount >= cycleSize) { cycleAmount = (cycleSize * 2) - cycleAmount; } } else if (cycle.REVERSE < 6) { // Sine Wave cycleAmount = DFLOAT_MOD((timeNow / (1000 / cycleRate)), cycleSize); cycleAmount = Math.sin((cycleAmount * 3.1415926 * 2) / cycleSize) + 1; if (cycle.REVERSE == 4) { cycleAmount *= (cycleSize / 4); } else if (cycle.REVERSE == 5) { cycleAmount *= (cycleSize >> 1); } } if (cycle.REVERSE == 2) { reverseColours(sourceColours, cycle); } if (USE_BLEND_SHIFT) { blendShiftColours(sourceColours, cycle, cycleAmount); } else { shiftColours(sourceColours, cycle, cycleAmount); } if (cycle.REVERSE == 2) { reverseColours(sourceColours, cycle); } } colours = sourceColours; } // This utility function allows for variable precision floating point modulus. private double DFLOAT_MOD(final double d, final double b) { return (Math.floor(d * PRECISION) % Math.floor(b * PRECISION)) / PRECISION; }

  Read the article

• HighPoint RocketRAID 62x Controller

  - by TeXnewbie

  I have the subject card recently installed in Ubuntu 12.04.1 LTS (GNU/Linux 3.2.0-31-generic x86_64). See partial lspci -vv listing below (complete listing played havoc with pre tags): 03:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0622 (rev 01) Subsystem: HighPoint Technologies, Inc. Device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 9c00 [size=8] Region 1: I/O ports at 9800 [size=4] Region 2: I/O ports at 9400 [size=8] Region 3: I/O ports at 9000 [size=4] Region 4: I/O ports at 8c00 [size=16] Region 5: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K] Expansion ROM at fdbe0000 [disabled] [size=64K] Capabilities: I followed instructions I found at https://help.ubuntu.com/community/RocketRaid to compile the drivers for it, and although performing the process described there seemed to work fine with no noticeable errors, when I rebooted after performing that procedure I could not boot. During dkms steps, I noticed messages indicating that (If next boot fails, revert to initrd.img-3.2.0-31-generic.old-dkms image) update-initramfs................ so I booted using a Ubuntu 12.10 LiveDVD and reverted to the old-dkms initrd.img as suggested above, but this failed to repair the boot problem. Ultimately, I used https://help.ubuntu.com/community/Boot-Repair in Ubuntu-Secure-Remix to fix the boot problem and was able to boot normally again, but now with the newly generated initrd.img in place again (which now boots normally), when I modprobe the rr62x kernel module, I immediately get a hard crash with messages to console about a kernel paging request that seems to have caused the problem. I've tried on multiple occasions now to use the newly built kernel module so as to allow me to use an eSATA port multiplier plugged into the card, but to no avail. Any suggestions on fixes or workarounds (I've read that some of the HighPoint cards (2720SGL) seem to work as a host bus adapter and thus may not need a custom driver, but that seems not to be the case for mine) would be most appreciated. My goal is to use the card as described here and with software RAID mdadm utilities. If necessary, I can hand-copy the console messages after the hard crash into a follow-up message, but I obviously can't do a cut/paste. I'll gladly provide any other details that are needed, but not sure what those would be at this point, so I'll refrain from adding other details for now. Thanks in advance for any help.

  Read the article

• Why am I getting a "network is unreachable" error on Ubuntu Server?

  - by jason328

  I'm a completely new to Ubuntu server and am having a hard time connecting the server to the internet. I first ran ping -n 8.8.8.8 connect:Network is unreachable Then I ran ifconfig Link encap:Local Loopback inet addr:127.0.0.1 Mask 255.0.0.0 inet6 addr: ::1/28Scope:host UP LOOPBACK RUNNING MTU:16436 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15360 (15.2KB) TX bytes:15360 (15.3KB) Here is ouput for sudo lspci -n 00:00.0 0600: 8086:2580 (rev 04) 00:02.0 0300: 8086:2582 (rev 04) 00:1d.0 0c03: 8086:2658 (rev 03) 00:1d.1 0c03: 8086:2659 (rev 03) 00:1d.0 0c03: 8086:265a (rev 03) 00:1d.0 0c03: 8086:265b (rev 03) 00:1d.0 0c03: 8086:265c (rev 03) 00:1e.0 0604: 8086:244e (rev d3) 00:1e.0 0401: 8086:266e (rev 03) 00:1f.0 0601: 8086:2640 (rev 03) 00:1f.0 0101: 8086:2651 (rev 03) 00:1f.0 0c05: 8086:266a (rev 03) 00:0b.0 0200: 8086:1654 (rev 03) lshw-c network returns WARNING: you should run this program as super-user. *-network DISABLED description:Ethernet interface product: NetXtreme BCM5705_2 Gigabit Ethernet vender: Broadcom Corporation physical id:b bus info:pci@0000:0a:0b.0 logical name: eth0 capabilities: bus_master_cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 firmware=5705-v3.18 latency=32 mingnt=64 multicast=yes port=twister pair lsmod code returned this Module Size Used By e100 37213 0 dm_crypt 23125 1 ppdev 17113 0 psmouse 87603 0 snd_intel8x0 38570 0 snd_ac97_codec 134826 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97188 2 snd_intel8x0, snd_ac97_codec serio_raw 13211 0 snd_timer 29990 1 snd_pcm snd 78855 4 snd_intel8x0, snd_ac97_codec, snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_intel8x0, snd_pcm ext2 73795 1 parport_pc 32866 1 mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev, parport_pc,lp usbhid 47199 0 hid 99559 1 usbhid tg3 152032 0 i915 468651 1 floppy 70365 0 drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 Again there is more but it's giving info on the driver itself. I know it works, I've used it. I assume then that my network got disabled when I installed Ubuntu Server. How do I enable it? I checked and the internet cable is connected to the D-link router. I have also used this same computer for internet access when I had Ubuntu Desktop installed so internet does work.

  Read the article

• Wireless not working on Dell Inspirion 1501 after upgrading to Ubuntu 12.04 tried steps in other threads

  - by mark burton

  I updated to Ubuntu 12.04 and now my wireless is not working. No icon for it. Tried some of the troubleshooting in other threads but can't get it to work. Would really appreciate any help Thanks! " *-network description: Network controller product: BCM4311 802.11a/b/g vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 02 serial: 00:19:b9:5c:d1:52 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=10.0.0.6 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff " lsub results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c526 Logitech, Inc. Nano Receiver $ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:05.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:06.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS482 [Radeon Xpress 200M] 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01) 08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 08:01.0 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 08:01.1 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01) rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• What are these errors when I try to "make" the driver of my wireless adapter?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Intel Centrino Wireless N 1000 doesn't work on a Lenovo Z560

  - by Timetraveler

  I upgraded my Ubuntu 11.04 to 11.10 and my Wifi has stopped working. I have a Lenovo Z560 that has Intel centrino wireless-N 1000. I have searched various threads having similar problems for a solution and have no success. The wlan0 is not even showing up in rfkill. Please help me find a solution. I am giving below the output of various debug commands. Thanks in advance. DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" ----##uname -a Linux gurucharapathy-laptop 3.0.0-17-generic-pae #30-Ubuntu SMP Thu Mar 8 17:53:35 UTC 2012 i686 i686 i386 GNU/Linux ----##lspci -nnk | grep -iA2 net 05:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0084] Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN [8086:1315] Kernel modules: iwlagn 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 ----##iwconfig lo no wireless extensions. eth0 no wireless extensions. ----##iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. ----##rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no ----##lsmod Module Size Used by rfcomm 38408 8 bnep 17923 2 parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 snd_hda_codec_hdmi 31426 1 snd_hda_codec_conexant 52460 1 uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 28358 2 snd_hda_codec 91859 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec joydev 17393 0 snd_pcm 80435 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 i915 509554 9 drm_kms_helper 32889 1 i915 snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28932 2 snd_pcm,snd_seq drm 196290 5 i915,drm_kms_helper snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq mei 36466 0 mac80211 393421 0 snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 13575 0 intel_ips 17753 0 btusb 18160 2 i2c_algo_bit 13199 1 i915 soundcore 12600 1 snd bluetooth 148839 23 rfcomm,bnep,btusb cfg80211 172427 1 mac80211 psmouse 63474 0 serio_raw 12990 0 snd_page_alloc 14108 2 snd_hda_intel,snd_pcm sparse_keymap 13658 1 ideapad_laptop wmi 18744 0 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 2 libahci 25761 1 ahci r8169 47200 0 ----##nm-tool NetworkManager Tool State: asleep Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: r8169 State: unmanaged Default: no HW Address: 88:AE:1D:DE:5F:9C Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on ----##lshw -C network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d6400000-d6401fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:de:5f:9c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.0.100 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff

  Read the article

• Endeca Information Discovery 3-Day Hands-on Training Workshop

  - by Mike.Hallett(at)Oracle-BI&EPM

  For Oracle Partners, on October 3-5, 2012 in Milan, Italy: Register here. Endeca Information Discovery plays a key role with your big data analysis and complements Oracle Business Intelligence Solutions such as OBIEE. This FREE hands-on workshop for Oracle Partners highlights technical know-how of the product and helps understand its value proposition. We will walk you through four key components of the product: Oracle Endeca Server—A highly scalable, search-analytical database that derives the data model based on the data presented to it, thereby reducing data modeling requirements. Studio—A highly interactive, component-based user interface for configuring advanced, yet intuitive, analytical applications. Integration Suite—Provides rapid unification and enrichment of diverse sources of information into a single integrated view. Extensible Value-Added Modules—Add-on modules that provide value quickly through configuration instead of custom coding. Topics covered will include Data Exploration with Endeca Information Discovery, Data Ingest, Project Lifecycle, Building an Endeca Server data model and advanced modeling techniques, and Working with Studio. Lab Outline The labs showcase Oracle Endeca Information Discovery components and functionality by providing expertise on features and know-how of building such applications. The hands-on activities are based on a Quick Start application provided during the class. Audience Oracle Partners, Big Data Analytics Developer and Architects BI and EPM Application Developers and Implementers, Data Warehouse Developers Equipment Requirements This workshop requires attendees to provide their own laptops for this class. Attendee laptops must meet the following minimum hardware/software requirements: Hardware 8GB RAM is highly recommended (Windows 64 bit Machine is required) 40 GB free space (includes staging) USB 2.0 port (at least one available) Software One of the following operating systems: 64-bit Windows host/laptop OS (Windows 7 or Windows Server 2008) 64-bit host/laptop OS with a Windows VM (Server, or Win 7, BIC2g, etc.) Internet Explorer 8.x , Firefox 3.6 or Firefox 6.0 WINRAR or 7ziputility to unzip workshop files: Download-able from http://www.win-rar.com/download.html Download-able from http://www.7zip.com/ Oracle Endeca Information Discovery Workshop Register here: October 3-5, 2012: Cinisello Balsamo, Milan.  We will confirm with you your place within 2 weeks. Questions?  Send email to: [email protected]  :  Oracle Platform Technologies Enablement Services.

  Read the article

• KVM Bridged Network Not Working

  - by EApubs

  I just installed KVM on my Ubuntu Server according to this guide : https://help.ubuntu.com/community/KVM/Installation Then prepared a bridged network as shown in here : https://help.ubuntu.com/community/KVM/Networking Then, I created a virtual machine with virt-manager. I tried several times but the guest fails to connect to the network! Any help? ifconfig : br0 Link encap:Ethernet HWaddr d0:27:88:b0:e4:38 inet addr:192.168.20.100 Bcast:192.168.20.255 Mask:255.255.255.0 inet6 addr: fe80::d227:88ff:feb0:e438/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10493 (10.4 KB) TX bytes:8433 (8.4 KB) eth0 Link encap:Ethernet HWaddr d0:27:88:b0:e4:38 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:63 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11361 (11.3 KB) TX bytes:8479 (8.4 KB) Interrupt:41 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) virbr0 Link encap:Ethernet HWaddr 5a:8c:57:95:af:3b inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) brctl show : bridge name bridge id STP enabled interfaces br0 8000.d02788b0e438 no eth0 virbr0 8000.000000000000 yes brctl showmacs br0 : port no mac addr is local? ageing timer 1 5c:d9:98:67:b6:28 no 48.33 1 d0:27:88:b0:e4:38 yes 0.00 1 e0:2a:82:f9:6c:09 no 0.00 ip route : default via 192.168.20.1 dev br0 metric 100 192.168.20.0/24 dev br0 proto kernel scope link src 192.168.20.100 192.168.122.0/24 dev virbr0 proto kernel scope link src 192.168.122.1 *In the guest * I was unable to copy paste the info from the guest because can't ssh to it. It didn't get any ip from DHCP. Won't work even after setting it up manually.

  Read the article

• RPi and Java Embedded GPIO: Sensor Connections for Java Enabled Interface

  - by hinkmond

  Now we're ready to connect the hardware needed to make a static electricity sensor for the Raspberry Pi and use Java code to access it through a GPIO port. First, very carefully bend the NTE312 (or MPF-102) transistor "gate" pin (see the diagram on the back of the package or refer to the pin diagram on the Web). You can see it in the inset photo on the bottom left corner. I bent the leftmost pin of the NTE312 transistor as I held the flat part toward me. That is going to be your antenna. So, connect one of the jumper wires to the bent pin. I used the dark green jumper wire (looks almost black; coiled at the bottom) in the photo. Then push the other 2 pins of the transistor into your breadboard. Connect one of the pins to Pin # 1 (3.3V) on the GPIO header of your RPi. See the diagram if you need to glance back at it. In the photo, that's the orange jumper wire. And connect the final unconnected transistor pin to Pin # 22 (GPIO25) on the RPi header. That's the blue jumper wire in my photo. For reference, connect the LED anode (long pin on a common anode LED/short pin on a common cathode LED, check your LED pin diagram) to the same breadboard hole that is connecting to Pin # 22 (same row of holes where the blue wire is connected), and connect the other pin of the LED to GROUND (row of holes that connect to the black wire in the photo). Test by blowing up a balloon, rubbing it on your hair (or your co-worker's hair, if you are hair-challenged) to statically charge it, and bringing it near your antenna (green wire in the photo). The LED should light up when it's near and go off when you pull it away. If you need more static charge, find a co-worker with really long hair, or rub the balloon on a piece of silk (which is just as good but not as fun). Next blog post is where we do some Java coding to access this sensor on your RPi. Finally, back to software! Ha! Hinkmond

  Read the article

• Can I prevent an IDENTIFY PACKET DEVICE command to a specific device at boot?

  - by Brian Spisak

  This is related to a previous question related to installation that is now resolved. I'm opening a new question, because I still need to get my DVD drive working. Problem: Failed boot when my ASUS DRW-24B1/ST DVD drive is attached to my asmedia ASM1061. Symptom: ata8.00: exception Emask 0x52 Sact 0x0 SErr 0xffffffff action 0xe frozen ata8: SError: { blah blah } ata8.00: failed command: IDENTIFY PACKET DEVICE ata8.00: cmd blah blah res blah blah (ATA bus error) ata8.00: status: { DRDY } ata8: hard resetting link Background: The ASM1061 is a PCIe to SATA bridge providing 2 x 6Gb/s ports and is supposed to be fully compliant to SATA specs. I just discovered in the fine print of my ASUS P8Z77-V pro motherboard that "These SATA ports are for data hard drivers only. ATAPI devices are not supported." However, I have already installed Windows 7 using this drive and I can run the Ubuntu 12.04 installer from it as well. The only time I have a problem is during Ubuntu boot when it tries an IDENTIFY PACKET DEVICE which seems to be an ATAPI command. I can't simply switch this device to another SATA port because they are already allocated to other devices. (My chipset's 2 x 6Gb/s are connected to my boot SSD and a fast HDD while the 4 x 3Gb/s ports are running a RAID 5 array.) If this can't be fixed or worked around, I suppose I'll have to go buy SATA add-in card. Blech. Thoughts: If indeed this is a device specific issue (that it doesn't support ATAPI discovery) then I can't expect - is it udev? - to work with it. But, it seems that Windows and even the Ubuntu installer work just fine. So why does udev have a problem? At the end of the day, it would be nice to have the DVD working under Ubuntu, but I can live without it. But, as this is a dual-boot machine, I can't physically disconnect it because I want it to work with Windows. (And physically disconnecting it every time I want to boot Ubuntu is NOT an option. ;-) Questions: Should this be considered a bug? My feelings are that if it works with other OS that it should probably work with Ubuntu as well. How can I work around this problem? I have a limited knowledge of linux internals, but it seems I should be able to somehow tell udev (or whatever is doing the discovery) to ignore that device. Is there a way?

  Read the article

• Ubuntu Server Cannot Route to the Internet

  - by ejes

  I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

  Read the article

• Apache - create multiple aliases

  - by mc3mcintyre

  I'm trying to setup two websites on my Apache server. One is www.domain.com and the other is test.domain.com. Currently, my 000-default.conf file reads as follows: <VirtualHost www:80> # The ServerName directive sets the request scheme, hostname and port that # the server uses to identify itself. This is used when creating # redirection URLs. In the context of virtual hosts, the ServerName # specifies what hostname must appear in the request's Host: header to # match this virtual host. For the default virtual host (this file) this # value is not decisive as it is used as a last resort host regardless. # However, you must set it for any further virtual host explicitly. #ServerName www.domain.com #ServerAlias www ServerAdmin [email protected] DocumentRoot /var/www/domain.com/ # Available loglevels: trace8, ..., trace1, debug, info, notice, warn, # error, crit, alert, emerg. # It is also possible to configure the loglevel for particular # modules, e.g. #LogLevel info ssl:warn ErrorLog ${APACHE_LOG_DIR}/domain.error.log CustomLog ${APACHE_LOG_DIR}/domain.access.log combined UseCanonicalName on allow from all Options +Indexes # For most configuration files from conf-available/, which are # enabled or disabled at a global level, it is possible to # include a line for only one particular virtual host. For example the # following line enables the CGI configuration for this host only # after it has been globally disabled with "a2disconf". #Include conf-available/serve-cgi-bin.conf </VirtualHost> <VirtualHost test:80> DocumentRoot "/var/www/domain.com/test/" ServerName test.domain.com ServerAdmin [email protected] ErrorLog ${APACHE_LOG_DIR}/test.domain.error.log CustomLog ${APACHE_LOG_DIR}/test.domain.access.log combined UseCanonicalName on allow from all Options +Indexes </VirtualHost> # vim: syntax=apache ts=4 sw=4 sts=4 sr noet As is, when I use a browser to go to the www location, it show me a directory listing. However, if I remove the www:80 on Line 1 and replace it with *:80, it correctly displays the webpage. I don't understand why. Can anyone help me configure this 000-default.conf file so that www goes to "/var/www/domain.com" and that test goes to "/var/www/domain.com/test"? Thank you.

  Read the article

• Investing in Servers by Intel

  - by Koushal Deshpande

  Originally posted on: http://geekswithblogs.net/BizTalkAndOtherTechs/archive/2013/10/31/investing-in-servers-by-intel.aspxA nice article reference from Intel, refer here. Referees to cloud as well. Choose correctly what you need. 1 Do determine right server for your company. There is no use getting a server that has redundant services but still add to the costs. 2 Do get servers that can be upgraded. A server with limited memory and storage may not be able to keep up with your business growth. The basic memory and storage options might not be sufficient. Consider at least 8GB of RAM and 1 terabyte of hard disk space. 3 Do check the server has at least one Gigabit Ethernet port. This allows high speed transferring of files and increases productivity for your employees. USB and Firewire ports may not be enough as their transfer speed is too low and will affect the productivity of your company. Infinite Technologies is ready to help perform this upgrade. Contact Infinite Technologies now View our other resellers » 4 Do verify that the server comes with documentation. Documentation allows you to make a claim when your server breaks down and is supported by a warranty. 6 Do check the support options for the server from the manufacturer. Different manufacturer has different support options such as maintenance plans and software upgrades. 5 Do always look into the warranty. Get an enhanced warranty that guarantees response and repair time to avoid disruption. 7 Do get server management tools that can be used on any computer. Server management tools should be cross compatible across different operating systems to take into account future PC replacements. 8 Do check the power usage of the servers. Get the right power supply to avoid damaging server hardware and consider the Intel® Xeon® E3 processor to help save on your electricity bills. 9 Do check what built-in security packages are available. Ensure that your server is protected. Built-in security1 helps you save on getting add on security packages.

  Read the article

• Sharing one static ip for both ftp and www service

  - by user11496

  Trying to figure out how to update the Zone record and configure webserver so that one application on the webserver is accessible by public. I'm completely not good at NS/DNS/NAT/firewall/routing/port forwarding/networking etc. "faraday" is the intranet name. Everyone within local network can access all applications hosted on "faraday". Hostname for webserver is "www", FTP server is "ftpserver". Both servers running RHEL4 OS. The goal is to allow anyone outside the company network (public) to access only one of the many applications on "faraday". Hope somebody can help me with some of the questions below, if not all. From zoneedit record, the static IP is used by FTP now. Can I use the same existing static IP - 219.95.10.100, for web service? Currently anyone who enter "http://www.abc.com.my" will be directed to "http://www.abc.com". I don't want this to change. Currently, no one else, except employee on local network, can access "faraday" web pages. How to configure so that when anyone type "http://thisapp.abc.com.my" on their web browser, the url will lead them to "http://faraday/thisapp" (application folder is /var/www/html/thisapp on RHEL4 web server). If possible, how to set the URL will continue to show "http://thisapp.abc.com.my" instead of "http://faraday/thisapp" How to limit/restrict user (those who are not from local network) so they only have access to "http://thisapp.abc.com.my", but not "http://faraday" or "http://faraday/anotherapp", etc. What's the configuration changes needed in /etc/httpd.conf on web server? Company domain name is "abc.com.my". Following is the zone records on www.zoneedit.com. Subdomain Type IP sdsl A 219.95.10.100 ftp CNAME sdsl.abc.com.my @ NS ns3.zoneedit.com @ NS ns7.zoneedit.com WebForward record: New Domain Destination Cloaked www.abc.com.my http://www.abc.com N On my local DNS server, there are 2 zone files: abc.com.my and pnmy.abc.com. > cat abc.com.my.zone ftp CNAME ftp.pnmy.abc.com. sdsl A 219.95.10.100 > cat pnmy.abc.com.zone ftp CNAME ftpserver ftpserver A 172.16.5.1 faraday CNAME www www A 172.16.5.2

  Read the article

• Best Language for the job? Database | C++, .NET, Java

  - by Randy E

  Ok, quick overview. I'm pretty brand new to software design. I have experience reading and editing/customizing PHP things for online scripts/software; Such as CMS, Wordpress, some forum solutions. I'm about to begin my degree in Software Design, the school I'm going to will allow us to kind of focus on an area, C++, Java, or .NET. I've played around a little with VB over the past week, mostly just trying to get a slight feel for it, however nothing extensive. I've been through Herbert Schildt's "C++, A Beginner's Guide." but I was mainly reading it, not doing anything with it beyond a couple basic Console Apps (and getting frustrated with auto-close :/ ). Now, where I decide to focus more in with my degree will depend on what the best language for the job is for my first piece of software I want to develop on my own. Assume I haven't looked at any of the languages at all, please help with the following: My first piece of software will be a database program. Everything has to do with users inputting and retrieving data, and calling that data to help with another function of the software, automatically calculating billing information based on information inputted in the other portion of the program. I won't go into too many details as I'm targeting a niche that doesn't have too much competition, but the competition that is there is established. I want to offer more features, scalable solutions, and the ability to port it to an online version. Ok, basically, it is a complete case management with integrated billing for Private Investigators. I would like the case management to be able to check the Database to see if certain information has been inputted before (such as Names/SSN's), and then the billing will pull hours inputted in the case portion for investigative work, multiplying by an already inputted amount for the fee, and then calculate sales tax. I also want to provide potential clients with an easily scalable solution, that is, a basic option for start ups that costs the least amount, with no additional users, ran on one machine. A middle option with the ability to create users and place them in two groups (User or Admin), as well as adding a few additional features, ran on one machine, but this will allow it to be accessed after being mapped on a network drive. And a third option to allow the placement into 4 different groups (Investigators, Billing, Managers, Admins) and more features. And then, a couple of years after launch, a 4th option that is browser based allowing the same 4 groups to login, as well as clients (view things concerning their case, with some admin customizable objects that can be added for clients view), over the internet. The only licensing security I would like to employ right off the bat will be serial key generated after ordering online (received in an email after the successful purchase). The program will access a database stored on a server periodically to verify license. I would like it to be able to check to make sure it's the most updated version and automatically update if not.

  Read the article

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

• Precise Touch Screen Dragging Issue: Trouble Aligning with the Finger due to Different Screen Resolution

  - by David Dimalanta

  Please, I need your help. I'm trying to make a game that will drag-n-drop a sprite/image while my finger follows precisely with the image without being offset. When I'm trying on a 900x1280 (in X [900] and Y [1280]) screen resolution of the Google Nexus 7 tablet, it follows precisely. However, if I try testing on a phone smaller than 900x1280, my finger and the image won't aligned properly and correctly except it still dragging. This is the code I used for making a sprite dragging with my finger under touchDragged(): x = ((screenX + Gdx.input.getX())/2) - (fruit.width/2); y = ((camera_2.viewportHeight * multiplier) - ((screenY + Gdx.input.getY())/2) - (fruit.width/2)); This code above will make the finger and the image/sprite stays together in place while dragging but only works on 900x1280. You'll be wondering there's camera_2.viewportHeight in my code. Here are for two reasons: to prevent inverted drag (e.g. when you swipe with your finger downwards, the sprite moves upward instead) and baseline for reading coordinate...I think. Now when I'm adding another orthographic camera named camera_1 and changing its setting, I recently used it for adjusting the falling object by meter per pixel. Also, it seems effective independently for smartphones that has smaller resolution and this is what I used here: show() camera_1 = new OrthographicCamera(); camera_1.viewportHeight = 280; // --> I set it to a smaller view port height so that the object would fall faster, decreasing the chance of drag force. camera_1.viewportWidth = 196; // --> Make it proportion to the original screen view size as possible. camera_1.position.set(camera_1.viewportWidth * 0.5f, camera_1.viewportHeight * 0.5f, 0f); camera_1.update(); touchDragged() x = ((screenX + (camera_1.viewportWidth/Gdx.input.getX()))/2) - (fruit.width/2); y = ((camera_1.viewportHeight * multiplier) - ((screenY + (camera_1.viewportHeight/Gdx.input.getY()))/2) - (fruit.width/2)); But the result instead of just following the image/sprite closely to my finger, it still has a space/gap between the sprite/image and the finger. It is possibly dependent on coordinates based on the screen resolution. I'm trying to drag the blueberry sprite with my finger. My expectation did not met since I want my finger and the sprite/image (blueberry) to stay close together while dragging until I release it. Here's what it looks like: I got to figure it out how to make independent on all screen sizes by just following the image/sprite closely to my finger while dragging even on most different screen sizes instead.

  Read the article

< Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >