Search Results

Search found 10536 results on 422 pages for 'cpu usage'.

Page 321/422 | < Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >

• Strange performance issue with Dell R7610 and LSI 2208 RAID controller

  - by GregC

  Connecting controller to any of the three PCIe x16 slots yield choppy read performance around 750 MB/sec Lowly PCIe x4 slot yields steady 1.2 GB/sec read Given same files, same Windows Server 2008 R2 OS, same RAID6 24-disk Seagate ES.2 3TB array on LSI 9286-8e, same Dell R7610 Precision Workstation with A03 BIOS, same W5000 graphics card (no other cards), same settings etc. I see super-low CPU utilization in both cases. SiSoft Sandra reports x8 at 5GT/sec in x16 slot, and x4 at 5GT/sec in x4 slot, as expected. I'd like to be able to rely on the sheer speed of x16 slots. What gives? What can I try? Any ideas? Please assist Cross-posted from http://en.community.dell.com/support-forums/desktop/f/3514/t/19526990.aspx Follow-up information We did some more performance testing with reading from 8 SSDs, connected directly (without an expander chip). This means that both SAS cables were utilized. We saw nearly double performance, but it varied from run to run: {2.0, 1.8, 1.6, and 1.4 GB/sec were observed, then performance jumped back up to 2.0}. The SSD RAID0 tests were conducted in a x16 PCIe slot, all other variables kept the same. It seems to me that we were getting double the performance of HDD-based RAID6 array. Just for reference: maximum possible read burst speed over single channel of SAS 6Gb/sec is 570 MB/sec due to 8b/10b encoding and protocol limitations (SAS cable provides four such channels).

  Read the article

• 16-bit MS-DOS Subsystem: csrss.exe

  - by Wesley

  Hi all, I just booted up my Samsung N120 netbook (with Windows XP Home SP3) and a dialog box came up with a command prompt window behind it. The dialog box is titled 16 bit MS-DOS Subsystem and the message is as follows: C:\DOCUME~1\SAMSUNG\csrss.exe The NTVDM CPU has encountered an illegal instruction. CS:0544 IP:0117 OP:63 00 64 00 34 Choose 'Close' to terminate the application. This only started on my most recent boot-up. One thing to note is that when I downloaded the Dropbox installer and opened it up, Panda Cloud Antivirus detected a suspicious file, which was csrss.exe and "neutralized it." However, an actual virus or trojan was not detected immediately before the file was detected and neutralized. Just under two weeks ago, a trojan and two viruses were detected for some odd reason. (I only went to website I knew and I do not torrent or browse adult sites.) Anyhow, the two viruses came up in temporary files and the trojan was "neutralized." Anyways, the main question is: How can I repair the csrss.exe file such that Windows XP starts up properly? A screenshot could be posted upon request. Thanks in advance!

  Read the article

• Finding all IP ranges blelonging to a specific ISP

  - by Jim Jim

  I'm having an issue with a certain individual who keeps scraping my site in an aggressive manner; wasting bandwidth and CPU resources. I've already implemented a system which tails my web server access logs, adds each new IP to a database, keeps track of the number of requests made from that IP, and then, if the same IP goes over a certain threshold of requests within a certain time period, it's blocked via iptables. It may sound elaborate, but as far as I know, there exists no pre-made solution designed to limit a certain IP to a certain amount of bandwidth/requests. This works fine for most crawlers, but an extremely persistent individual is getting a new IP from his/her ISP pool each time they're blocked. I would like to block the ISP entirely, but don't know how to go about it. Doing a whois on a few sample IPs, I can see that they all share the same "netname", "mnt-by", and "origin/AS". Is there a way I can query the ARIN/RIPE database for all subnets using the same mnt-by/AS/netname? If not, how else could I go about getting every IP belonging to this ISP? Thanks.

  Read the article

• big speed difference on a network link with and without VPN tunnel

  - by xirtyllo

  Scenario: We have a network link between two offices. The link is provided by a third party company through a VLAN on their network, but to us it is totally transparent -as if we had a simple ethernet cable going from one location to the other-. We have one router at each side of the link, with 3 VPN tunnels in between the two. The test: When I test the speed of the network link with the routers in place, with one laptop directly connected to the router on each side, I consistently get ~30/35Mbps. But if I take out the routers and I test the link connecting the laptops directly to the ethernet cable at each side, I consistently get ~85/88Mbps. It's quite a big performance hit, and I would tend to think that the VPN tunnels are responsible for the slow down. Is it normal that this configuration (two routers with three VPN tunnels between them) takes away so much bandwidth? More info: The encryption algorithm used for the VPN tunnels is AES128. The routers model is Zyxel USG200 and Zyxel USG1000, and their CPU, memory, and storage use is well within normal limits. The nominal bandwidth of the network link is 100Mbps. The network link in question is supplied by a third party company (the building in between our two offices). Basically it passes through their network as a VLAN, but the VLAN is completely transparent to us (e.g. no configuration required on our side, just like one single cable from end to end). Unfortunately (or maybe fortunately) I cannot directly test different routers configurations as I'm not the person in charge of it.

  Read the article

• what can be causes of http server crash?

  - by mithunmo

  Hello , I am using WAMP server on Windows XP. Apache 2.2.11 MySQL 5.1.36 (INNODB engine) PHP 5.3.0 I observe that my WAMP server crashes in the following scenarios IF I use a Low end PC ( low processor speed and low RAM) After making some changes to httpd.conf file .For eg changing the Allow from IP address . But here it crashes only once and then it starts to work fine. Random crashes CRASH LOG szAppName : httpd.exe szAppVer : 2.2.11.0 szModName : php5ts.dll szModVer : 5.3.0.0 offset : 0000c309 C:\DOCUME~1\blrcom\LOCALS~1\Temp\WERc677.dir00\httpd.exe.mdmp C:\DOCUME~1\blrcom\LOCALS~1\Temp\WERc677.dir00\appcompat.txt My questions Does high CPU utilization/LOW RAM can also cause the HTTP server to crash ? excessive file reading as in every 10 seconds ? unlimited script execution time . I have set the maximum execution time in php script to 0 as my script has to execute for sometimes 2-3 days. Is there any way to avoid this ? Access to Database ? Should we use lock before reading and writing Can these be the reasons for random wamp server crashes ? OR is is some other programming error ? Please guide me . Regards, Mithun

  Read the article

• How do I improve my incremental-backup performance?

  - by Alistair Bell

  I'm currently using the traditional rsync+cp -al method to create incremental/snapshot backups of our server tree. The backups are going onto a pair of eight-disk towers connected to the backup machine (a Sandy Bridge machine with 16 GB of RAM, running CentOS 5.5) via four eSATA connections (four disks per connection). Each disk is a regular 2 TB disk, so we have 32 TB of disk space connected to the backup machine. We're backing up about 20 TB of data on the servers with this. The problem is that each daily backup is taking more than 24 hours, and the real time-killer isn't the actual rsync, but the time it takes to perform a cp -al of the tree locally on the backup machine. It's taking more than 12 hours just to make the shadow copy of the tree, and as far as I can tell the performance backlog is at the disk (top shows the cp using a lot of RAM but not a lot of CPU and mostly in uninterruptible-sleep state) We have the server data split into four major volumes (and a few minor ones), and each of these backups runs in parallel (with some offsets in the cron to try to get some disks' cp done first). There are two volumes on the backup drive, both striped LVM volumes of 16 TB each. So obviously I need to improve the performance because it's unusable as it stands. The first question is: when CentOS 6 comes out, with support for btrfs, will making snapshots of subvolumes with btrfs substantially increase this performance? The second is: is there a way, with ext3 or something else supported in CentOS 5 or 6, to 'encourage' it to put the directories/inodes in one part of a volume (which could happen to be the part that's on an SSD, via LVM) and the files in another? That would presumably solve the problem, but I don't know of ways to hint ext3 like that.

  Read the article

• Help building maya render node spec

  - by Ak

  Hi there, I'm looking to build 4x Maya render slaves/nodes for a friend of mine when his project gets green lit. The project involves MentalRay and lots of glass. I'm unsure if the new i7's 9xx or 8xx with hyper threading will do any better than a core 2 quad of the same (or close enough) speed. Does hyper threading make a difference to Maya or is it more performance per core based? I'm sure he's prefer I'd build another render node than pay for a bleeding edge CPU that only adds fractionly more GHz. -- The rest of the spec so far: 4Gb - 8Gb ram 64 bit OS: Probably Windows 7 (I know Linux is free, but want to build something my friend can support himself as easily as he supports his own workstation) 1TB HDD to hold textures, Maya files and renders which will be copied to central storage later Mobo with on-board video, gigabit NIC 500 - 650 watt PSU Desktop case something like a: Cooler Master ATCS 840 The machines will sold afterwards if necessary. -- If anyone has had experience in Maya and has done any tests with the new CPUs vs. the older ones I'd really appreciate your input.

  Read the article

• Improving Performance of RDP Over LAN

  - by Jared Brown

  Architecture: A deployment of 6 new HP thin clients (Windows XP Embedded) with TCP/IP access to several new HP servers (Windows 2003 Server). Each thin client is connected over fiber optic to a Gigabit Cisco switch, which the servers are connected to. There are 10/100 Ethernet to fiber converter boxes on each end of the fiber cables. Problem: Noticeable lag over RDP while using the Unigraphics CAD package. 3D models take .5 to 1 second to respond to mouse actions. Other Details: Network throughput on each thin client's RDP session is 7288 kbps. RDP connection settings - color setting: 15k, all themes, etc. turned off. Local and remote system performance stats are well within norms (CPU, Memory, and Network). Question: Are there newer versions of terminal services or RDP I can use on my existing OSes? Are there compression algorithms, etc. that are well suited for a high-bandwidth LAN? Are there valid alternatives that will yield higher performance (i.e. UltraVNC with drivers installed)? Are there TCP/IP tuning options I can exploit?

  Read the article

• How to diagnose frequent segfaults

  - by Andreas Gohr

  My server is logging frequent segmentation faults to /var/log/kern.log in different tools. So far I've seen them in Perl, PHP and rsync. All installed software is up-to-date Debian packages. Here's an exerpt from the log file: Mar 2 01:07:54 gaz kernel: [ 5316.246303] imapsync[4533]: segfault at 8b ip 00007fb448c98fe6 sp 00007ffff571dd68 error 4 in libperl.so.5.10.1[7fb448bd7000+164000] Mar 2 01:17:42 gaz kernel: [ 5904.354307] php5-cgi[4441]: segfault at 2bb3dc8 ip 0000000002bb3dc8 sp 00007fffbeeaae48 error 15 Mar 2 02:54:05 gaz kernel: [11687.922316] php5-cgi[4495]: segfault at 2d7acf9 ip 0000000002d7acf9 sp 00007fff60c6eb18 error 15 Mar 2 10:50:08 gaz kernel: [40250.390322] BUG: unable to handle kernel paging request at 00000000024b03f0 Mar 2 10:50:08 gaz kernel: [40250.390341] IP: [<00000000024b03f0>] 0x24b03f0 Mar 2 10:50:08 gaz kernel: [40250.390353] PGD 208c71067 PUD 21c811067 PMD 209329067 PTE 8000000211c88067 Mar 2 10:50:08 gaz kernel: [40250.390365] Oops: 0011 [#1] SMP Mar 2 10:50:08 gaz kernel: [40250.390373] last sysfs file: /sys/devices/pci0000:00/0000:00:12.0/host4/target4:0:0/4:0:0:0/block/sdb/stat Mar 2 10:50:08 gaz kernel: [40250.390386] CPU 1 Mar 2 10:50:08 gaz kernel: [40250.390392] Modules linked in: cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_conservative xt_recent xt_tcpudp iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ ipv4 ip6table_filter ip6_tables xt_DSCP xt_TCPMSS ipt_LOG ipt_REJECT iptable_mangle iptable_filter xt_multiport xt_state xt_limit xt_conntrack nf_conntrack_ftp nf_conntrack ip_tables x_tables loop snd _hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm radeon snd_timer ttm snd drm_kms_helper soundcore drm snd_page_alloc i2c_algo_bit shpchp i2c_piix4 edac_core pcspkr k8temp evdev edac_m ce_amd pci_hotplug i2c_core button ext3 jbd mbcache dm_mod powernow_k8 aacraid 3w_9xxx 3w_xxxx raid10 raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid1 raid0 md_mod sata_nv sata_sil sata_via sd_mod crc_t10dif ata_generic ahci pata_atiixp ohci_hcd libata r8169 mii thermal ehci_hcd processor thermal_sys scsi_mod usbcore nls_base [last unloaded: scsi_wait_scan] Mar 2 10:50:08 gaz kernel: [40250.390566] Pid: 11482, comm: munin-limits Not tainted 2.6.32-5-amd64 #1 MS-7368 Mar 2 10:50:08 gaz kernel: [40250.390576] RIP: 0010:[<00000000024b03f0>] [<00000000024b03f0>] 0x24b03f0 Mar 2 10:50:08 gaz kernel: [40250.390586] RSP: 0018:ffff88021cc8dec0 EFLAGS: 00010286 Mar 2 10:50:08 gaz kernel: [40250.390593] RAX: 000000001ddc1000 RBX: 0000000000000010 RCX: ffffffff810f9904 Mar 2 10:50:08 gaz kernel: [40250.390600] RDX: 0000000000000000 RSI: ffffea0007688200 RDI: 0000000000000286 Mar 2 10:50:08 gaz kernel: [40250.390608] RBP: 00000000ffffffea R08: 0000000000000025 R09: 7865542f30312e35 Mar 2 10:50:08 gaz kernel: [40250.390615] R10: 000000d01cc8ddf8 R11: 0000000000000246 R12: ffff88021cc8def8 Mar 2 10:50:08 gaz kernel: [40250.390622] R13: 0000000002295010 R14: 00000000022c9db0 R15: 0000000002488d78 Mar 2 10:50:08 gaz kernel: [40250.390630] FS: 00007f3b3c8b2700(0000) GS:ffff880008d00000(0000) knlGS:0000000000000000 Mar 2 10:50:08 gaz kernel: [40250.390641] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Mar 2 10:50:08 gaz kernel: [40250.390648] CR2: 00000000024b03f0 CR3: 000000021c5d1000 CR4: 00000000000006e0 Mar 2 10:50:08 gaz kernel: [40250.390656] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Mar 2 10:50:08 gaz kernel: [40250.390663] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Mar 2 10:50:08 gaz kernel: [40250.390671] Process munin-limits (pid: 11482, threadinfo ffff88021cc8c000, task ffff88021bf59530) Mar 2 10:50:08 gaz kernel: [40250.390681] Stack: Mar 2 10:50:08 gaz kernel: [40250.390687] ffffffff810f1d4a ffff880208c63228 0000000000000000 00007fffc2dcecc0 Mar 2 10:50:08 gaz kernel: [40250.390697] <0> 00000000024ba2b0 0000000002295010 ffffffff810f1e3d 0000000000000004 Mar 2 10:50:08 gaz kernel: [40250.390712] <0> ffff88021bf59530 ffff88021c4edc00 ffffffff812fe0b6 ffff88021c4edc60 Mar 2 10:50:08 gaz kernel: [40250.390732] Call Trace: Mar 2 10:50:08 gaz kernel: [40250.390742] [<ffffffff810f1d4a>] ? vfs_fstatat+0x2c/0x57 Mar 2 10:50:08 gaz kernel: [40250.390750] [<ffffffff810f1e3d>] ? sys_newstat+0x11/0x30 Mar 2 10:50:08 gaz kernel: [40250.390760] [<ffffffff812fe0b6>] ? do_page_fault+0x2e0/0x2fc Mar 2 10:50:08 gaz kernel: [40250.390768] [<ffffffff812fbf55>] ? page_fault+0x25/0x30 Mar 2 10:50:08 gaz kernel: [40250.390777] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b Mar 2 10:50:08 gaz kernel: [40250.390783] Code: Bad RIP value. Mar 2 10:50:08 gaz kernel: [40250.390791] RIP [<00000000024b03f0>] 0x24b03f0 Mar 2 10:50:08 gaz kernel: [40250.390799] RSP <ffff88021cc8dec0> Mar 2 10:50:08 gaz kernel: [40250.390805] CR2: 00000000024b03f0 Mar 2 10:50:08 gaz kernel: [40250.391051] ---[ end trace 1cc1473b539c7f6e ]--- Mar 2 11:42:20 gaz kernel: [43382.242301] php5-cgi[10963]: segfault at d81160 ip 0000000000d81160 sp 00007fff3adcb058 error 15 Mar 2 21:51:14 gaz kernel: [79916.418302] php5-cgi[20089]: segfault at 1c59dc8 ip 0000000001c59dc8 sp 00007fff9b877fb8 error 15 Mar 3 03:45:01 gaz kernel: [101143.334305] munin-update[22519] general protection ip:7f516dce204c sp:7fff6049a978 error:0 in libperl.so.5.10.1[7f516dc7d000+164000] Mar 3 11:22:37 gaz kernel: [128599.570307] php5-cgi[22888]: segfault at 36485a8 ip 00000000036485a8 sp 00007fff2d56e1c8 error 15 Mar 4 08:32:17 gaz kernel: [204779.842304] php5-cgi[22090]: segfault at 18 ip 0000000000689e5e sp 00007fff677a6a48 error 6 in php5-cgi[400000+6f9000] Mar 4 10:01:02 gaz kernel: [210104.434706] rsync[22236] general protection ip:7f14a07137f9 sp:7fff88f940b8 error:0 in libc-2.11.2.so[7f14a069d000+158000] Mar 4 11:32:22 gaz kernel: [215584.262316] BUG: unable to handle kernel paging request at 00000000ffffff9c Mar 4 11:32:22 gaz kernel: [215584.262331] IP: [<00000000ffffff9c>] 0xffffff9c Mar 4 11:32:22 gaz kernel: [215584.262343] PGD 0 Mar 4 11:32:22 gaz kernel: [215584.262350] Oops: 0010 [#2] SMP Mar 4 11:32:22 gaz kernel: [215584.262359] last sysfs file: /sys/devices/pci0000:00/0000:00:12.0/host4/target4:0:0/4:0:0:0/block/sdb/stat Mar 4 11:32:22 gaz kernel: [215584.262371] CPU 1 Mar 4 11:32:22 gaz kernel: [215584.262378] Modules linked in: cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_conservative xt_recent xt_tcpudp iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 ip6table_filter ip6_tables xt_DSCP xt_TCPMSS ipt_LOG ipt_REJECT iptable_mangle iptable_filter xt_multiport xt_state xt_limit xt_conntrack nf_conntrack_ftp nf_conntrack ip_tables x_tables loop snd_hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm radeon snd_timer ttm snd drm_kms_helper soundcore drm snd_page_alloc i2c_algo_bit shpchp i2c_piix4 edac_core pcspkr k8temp evdev edac_mce_amd pci_hotplug i2c_core button ext3 jbd mbcache dm_mod powernow_k8 aacraid 3w_9xxx 3w_xxxx raid10 raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid1 raid0 md_mod sata_nv sata_sil sata_via sd_mod crc_t10dif ata_generic ahci pata_atiixp ohci_hcd libata r8169 mii thermal ehci_hcd processor thermal_sys scsi_mod usbcore nls_base [last unloaded: scsi_wait_scan] Mar 4 11:32:22 gaz kernel: [215584.262552] Pid: 1960, comm: proxymap Tainted: G D 2.6.32-5-amd64 #1 MS-7368 Mar 4 11:32:22 gaz kernel: [215584.262563] RIP: 0010:[<00000000ffffff9c>] [<00000000ffffff9c>] 0xffffff9c Mar 4 11:32:22 gaz kernel: [215584.262573] RSP: 0018:ffff880209257e00 EFLAGS: 00010212 Mar 4 11:32:22 gaz kernel: [215584.262580] RAX: ffff8801514eb780 RBX: ffffffff810efb2d RCX: 0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262590] RDX: 0000000000000020 RSI: 0000000000000001 RDI: ffff8801514eb780 Mar 4 11:32:22 gaz kernel: [215584.262600] RBP: 00000000ffffffe9 R08: 0000000000000000 R09: 0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262611] R10: ffff880209257e78 R11: ffffffff81152c7c R12: 0000000000000001 Mar 4 11:32:22 gaz kernel: [215584.262622] R13: 0000000000008001 R14: 0000000000000024 R15: 00000000ffffff9c Mar 4 11:32:22 gaz kernel: [215584.262633] FS: 00007fca4de35700(0000) GS:ffff880008d00000(0000) knlGS:0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262644] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Mar 4 11:32:22 gaz kernel: [215584.262650] CR2: 00000000ffffff9c CR3: 00000001c9cbb000 CR4: 00000000000006e0 Mar 4 11:32:22 gaz kernel: [215584.262661] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262671] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Mar 4 11:32:22 gaz kernel: [215584.262682] Process proxymap (pid: 1960, threadinfo ffff880209256000, task ffff88021c4b1c40) Mar 4 11:32:22 gaz kernel: [215584.262693] Stack: Mar 4 11:32:22 gaz kernel: [215584.262698] ffffffff810f8566 ffff880209257e78 ffff88021c7bf000 ffff88021c7bf0c8 Mar 4 11:32:22 gaz kernel: [215584.262709] <0> 0000800000000000 ffff88021fc0f000 ffff880209257e78 00000000fffffffe Mar 4 11:32:22 gaz kernel: [215584.262724] <0> ffffffff810e5881 ffff880209257f48 0000000000000286 ffff88021fc0f000 Mar 4 11:32:22 gaz kernel: [215584.262743] Call Trace: Mar 4 11:32:22 gaz kernel: [215584.262753] [<ffffffff810f8566>] ? do_filp_open+0xa7/0x94b Mar 4 11:32:22 gaz kernel: [215584.262763] [<ffffffff810e5881>] ? virt_to_head_page+0x9/0x2a Mar 4 11:32:22 gaz kernel: [215584.262771] [<ffffffff810f9904>] ? user_path_at+0x52/0x79 Mar 4 11:32:22 gaz kernel: [215584.262779] [<ffffffff810cfec1>] ? get_unmapped_area+0xd7/0x139 Mar 4 11:32:22 gaz kernel: [215584.262787] [<ffffffff811019d5>] ? alloc_fd+0x67/0x10c Mar 4 11:32:22 gaz kernel: [215584.262795] [<ffffffff810eceaf>] ? do_sys_open+0x55/0xfc Mar 4 11:32:22 gaz kernel: [215584.262804] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b Mar 4 11:32:22 gaz kernel: [215584.262811] Code: Bad RIP value. Mar 4 11:32:22 gaz kernel: [215584.262819] RIP [<00000000ffffff9c>] 0xffffff9c Mar 4 11:32:22 gaz kernel: [215584.262828] RSP <ffff880209257e00> Mar 4 11:32:22 gaz kernel: [215584.262833] CR2: 00000000ffffff9c Mar 4 11:32:22 gaz kernel: [215584.263077] ---[ end trace 1cc1473b539c7f6f ]--- As you can see there are segfaults, a general protection fault and a Kernel Oops. My first guess was that there's a Hardware problem of some sort and I asked my Hoster (it's a rented root server) to do a full hardwarecheck - they did, but couldn't find any problem. I don't know what and how they checked but their support team is usually quite good. I ran memtester and cpuburn myself and couldn't find any error either. Unfortunately I have no reliable way to reproduce these segfaults, they seem to be more or less random. On a hunch I disabled the firewall of the system and ran one of the programs that segfaulted regularily (imapsync) and it seemed to take longer to segfault than before, so the problem might be related to the network stack. Or could just be a random thing. Here are the kernel specs: # uname -a Linux gaz 2.6.32-5-amd64 #1 SMP Wed Jan 12 03:40:32 UTC 2011 x86_64 GNU/Linux # cat /etc/debian_version 6.0 # lsmod Module Size Used by cpufreq_userspace 1992 0 cpufreq_stats 2659 0 cpufreq_powersave 902 0 cpufreq_conservative 5162 0 xt_recent 5977 0 xt_tcpudp 2319 0 iptable_nat 4299 0 nf_nat 13388 1 iptable_nat nf_conntrack_ipv4 9833 3 iptable_nat,nf_nat nf_defrag_ipv4 1139 1 nf_conntrack_ipv4 ip6table_filter 2384 0 ip6_tables 15075 1 ip6table_filter xt_DSCP 1995 0 xt_TCPMSS 2919 0 ipt_LOG 4518 0 ipt_REJECT 1953 0 iptable_mangle 2817 0 iptable_filter 2258 0 xt_multiport 2267 0 xt_state 1303 0 xt_limit 1782 0 xt_conntrack 2407 0 nf_conntrack_ftp 5537 0 nf_conntrack 46535 6 iptable_nat,nf_nat,nf_conntrack_ipv4,xt_state,xt_conntrack,nf_conntrack_ftp ip_tables 13899 3 iptable_nat,iptable_mangle,iptable_filter x_tables 12845 13 xt_recent,xt_tcpudp,iptable_nat,ip6_tables,xt_DSCP,xt_TCPMSS,ipt_LOG,ipt_REJECT,xt_multiport,xt_state,xt_limit,xt_conntrack,ip_tables loop 11799 0 radeon 573996 0 ttm 39986 1 radeon drm_kms_helper 20065 1 radeon snd_hda_codec_atihdmi 2251 1 drm 142359 3 radeon,ttm,drm_kms_helper snd_hda_intel 20019 0 i2c_algo_bit 4225 1 radeon pcspkr 1699 0 i2c_piix4 8328 0 snd_hda_codec 54244 2 snd_hda_codec_atihdmi,snd_hda_intel i2c_core 15712 5 radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_piix4 snd_hwdep 5380 1 snd_hda_codec snd_pcm 60503 2 snd_hda_intel,snd_hda_codec snd_timer 15582 1 snd_pcm snd 46446 5 snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer soundcore 4598 1 snd evdev 7352 3 snd_page_alloc 6249 2 snd_hda_intel,snd_pcm k8temp 3283 0 edac_core 29261 0 edac_mce_amd 6433 0 shpchp 26264 0 pci_hotplug 21203 1 shpchp button 4650 0 ext3 106518 2 jbd 37085 1 ext3 mbcache 5050 1 ext3 dm_mod 53754 0 powernow_k8 10978 1 aacraid 59779 0 3w_9xxx 28684 0 3w_xxxx 20569 0 raid10 17809 0 raid456 44500 0 async_raid6_recov 5170 1 raid456 async_pq 3479 2 raid456,async_raid6_recov raid6_pq 77179 2 async_raid6_recov,async_pq async_xor 2478 3 raid456,async_raid6_recov,async_pq xor 4380 1 async_xor async_memcpy 1198 2 raid456,async_raid6_recov async_tx 1734 5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy raid1 18431 3 raid0 5517 0 md_mod 73824 7 raid10,raid456,raid1,raid0 sata_nv 19166 0 sata_sil 7412 0 sata_via 7928 0 sd_mod 29889 8 crc_t10dif 1276 1 sd_mod ata_generic 3047 0 ahci 32374 6 r8169 29229 0 mii 3210 1 r8169 thermal 11674 0 pata_atiixp 3489 0 libata 133632 6 sata_nv,sata_sil,sata_via,ata_generic,ahci,pata_atiixp ohci_hcd 19212 0 ehci_hcd 31151 0 processor 29935 1 powernow_k8 thermal_sys 11942 2 thermal,processor scsi_mod 122149 5 aacraid,3w_9xxx,3w_xxxx,sd_mod,libata usbcore 122034 3 ohci_hcd,ehci_hcd nls_base 6377 1 usbcore # free total used free shared buffers cached Mem: 8166128 1228036 6938092 0 140412 782060 -/+ buffers/cache: 305564 7860564 Swap: 2102456 0 2102456 So, basically my questions are: How can I diagnose this further? Is there any data in the log above that could help me to isolate the troublemaker? Are there any known problems with the above hardware/software I overlooked when googling for it? Is there a way to prevent the kernel from autoloading modules (I probably don't need all these modules and one of them might be the culprit)

  Read the article

• Nagios plug-in check_snmp receives NO SNMP data from a CISCO Router

  - by Shehryar

  I have tried setting up Nagios on Ubuntu 10.10, successfully installed and can login to web interface, I am however stuck on configuring snmp or I am doing something wrong here, i have followed various sites / nagios wiki to setup configuration (cfg) files. When I check on the web interface, it gives the following error on one of my cisco router: Current Status: UNKNOWN (for 0d 2h 55m 56s) Status Information: SNMP problem - No data received from host CMD: /usr/bin/snmpget -t 1 -r 5 -m RFC1213-MIB -v 1 [authpriv] 192.168.1.1:161 ifOperStatus.1 On the command-line itself, when I type the following, it just sits there waiting and waiting : sudo /usr/local/nagios/libexec/check_snmp -H 192.168.1.1 -C Routers -o sysUpTime.0 When I type the following command : I get an OK /usr/bin/snmpget -v1 192.168.1.1:161 1.3.6.1.2.1.1.5.0 -c "Routers" I have configured SNMP properly on our cisco device as we can collect SNMP Data via two other monitoring tool (SolarWinds and Manage Engine), we are tempted towards Nagios as its opensource. Will be grateful if someone could assist in rectifying this situation and guide me with setting up nagios to monitor Cisco Routers, Switches and a Few Servers. We want to monitor Bandwidth, cpu utilization, uptime and other necessary counters. Will be grateful for your assistance Thanks for reading Shehryar

  Read the article

• Delay before download starts when serving files using nginx

  - by glumbo

  I am currently using nginx to serve downloads off my website. Users sometimes need to wait about 5 seconds before their download starts after clicking a download link. I'm not sure if I need to start using raid 10 (I'm currently using raid 50) or if this is a problem with my nginx configuration. I am also on a 1gbit line but download sometimes go as low as 10kB/s. My server: Dual Xeon 5620 CPU, 12x2TB drives with 8GB ram. This is my nginx.conf #user nobody; worker_processes 12; worker_rlimit_nofile 10240; worker_rlimit_sigpending 32768; error_log logs/error.log crit; #pid logs/nginx.pid; events { worker_connections 2048; } http { include mime.types; default_type application/octet-stream; access_log off; limit_conn_log_level info; log_format xfs '$arg_id|$arg_usr|$remote_addr|$body_bytes_sent|$status'; #sendfile on; #tcp_nopush on; reset_timedout_connection on; server_tokens off; autoindex off; keepalive_timeout 0; #keepalive_timeout 65; limit_zone one $binary_remote_addr 10m; perl_modules perl; perl_require download.pm;

  Read the article

• ESXi Server with 12 physical cores maxed out with only 8 cores assigned in virtual machines

  - by Sam

  I have an ESXi 5 server running on a 2-processor, 12-core system with hyperthreading enabled. So: 12 physical cores, 24 logical ones. On this server are 4 Windows 7 VMs, each configured for 2 processors, each running VMware Tools. Looking at my stats in vSphere, my "core utilization" is constantly maxed out. Yes, these machines are working hard, but only 8 cores have been allocated. How is this possible? Should I look into reducing the processor count per machine as in this post: VMware ESX server? I checked to ensure that hardware virtualization is enabled in the BIOS of the machine (a DELL R410). I've also started reading up on configuration, but being a newbie there's a lot of material to catch up on. It also seems I should only bother with advanced settings and pools if I'm really pushing the load, and I don't think that I should be pushing it with so few VMs. I suspect that I have some basic, incorrect configuration setting, but it's also possible that I have some giant misconceptions about virtualization. Any pointers? EDIT: Given the responses I've gotten so far, it seems that this is a measurement problem and not a configuration problem, making this less critical. Perhaps the real question is: How does the core utilization of the server reach a higher percentage than all individual cores' core utilization, and given that this possibility makes the metric useless for overall server load, what is the best global metric for measuring CPU load on hyper-threaded systems?

  Read the article

• Slow VM on esxi 4.1

  - by user57432

  We have a FreeBSD 64bit running on a esxi 4.1, the hardware platform is a DELL R710 with 2 x 56xx (intel 6core cpu) and 48 GB ram. The FreeBSD vm is very slow, when we compiles/builds something on it, it takes 5 minuts and it says "build time 18 seconds.". There's no vmtools installed on the vm. The same vm is installaed on another R710 running esxi 4.0 for dell and there's no problems with that one. Does anyone have any idea about what to look for? the VMs on the second server (ESXi 4.1) is a clone of the VMs running on the first VMserver (ESXi 4.0 Dell edition). It's not possible for me to move the VM back to the first server since the file contaning the vm is too big. We installed the new esxi with a datasore with 8mb blocks because 1mb blocks dident allow for the file size we needed. It looks like the www server on the new ESXi 4.1 works fine, but I havent really tested it. There's not installed vmtools on any of the VMs (FreeBSD). The block size on the second VM (ESXi 4.1) datastorage is 8mb and 1mb on the first (ESXi 4.0)

  Read the article

• fail2ban Error Gentoo

  - by Mark Davidson

  Hi All I've recently setup a new VPS running Gentoo (My first time using the distro so please forgive me is this is a really easy one) and as I've done with other servers installed fail2ban. Setting it up to block the host via iptables, on too many unsuccessful logins with ssh. However I'm getting a strange error that I can't quite solve. When I start fail2ban I get these lines in the error log 2009-11-13 18:02:01,290 fail2ban.jail : INFO Jail 'ssh-iptables' started 2009-11-13 18:02:01,480 fail2ban.actions.action: ERROR iptables -N fail2ban-SSH iptables -A fail2ban-SSH -j RETURN iptables -I INPUT -p tcp --dport ssh -j fail2ban-SSH returned 100 If I try and force a ban these errors show up in the log and the host is not banned 2009-11-13 11:23:26,905 fail2ban.actions: WARNING [ssh-iptables] Ban XXX.XXX.XXX.XXX 2009-11-13 11:23:26,929 fail2ban.actions.action: ERROR iptables -n -L INPUT | grep -q fail2ban-SSH returned 100 2009-11-13 11:23:26,930 fail2ban.actions.action: ERROR Invariant check failed. Trying to restore a sane environment 2009-11-13 11:23:27,007 fail2ban.actions.action: ERROR iptables -N fail2ban-SSH iptables -A fail2ban-SSH -j RETURN iptables -I INPUT -p tcp --dport ssh -j fail2ban-SSH returned 100 2009-11-13 11:23:27,016 fail2ban.actions.action: ERROR iptables -n -L INPUT | grep -q fail2ban-SSH returned 100 2009-11-13 11:23:27,016 fail2ban.actions.action: CRITICAL Unable to restore environment My versions are as follows Linux masked 2.6.18-xen-r12 #2 SMP Wed Mar 4 11:45:03 GMT 2009 x86_64 Intel(R) Xeon(R) CPU E5504 @ 2.00GHz GenuineIntel GNU/Linux net-analyzer/fail2ban-0.8.4 net-firewall/iptables-1.4.3.2 If anyone could shead some light on these errors that would be great, I did wonder if it was a problem with iptables or some kernel modules but I can block an IP if I do. iptables -I INPUT -s 25.55.55.55 -j DROP so makes me think its something a bit more unusual. Thanks a lot in advance

  Read the article

• Hylafax: Encounter "No font metric information" when try to send a fax

  - by Chau Chee Yang

  I am using Hylafax 6.0.5 on Fedora 13 x86_64. As there are no rpm package available for Fedora 13, I use the source tar ball to install hylafax myself. Everything seems fine during compile and install. I try to send a fax with sendfax and encounter error: # sendfax -n -d <fax-number> /etc/passwd /usr/local/sbin/textfmt: No font metric information found for "Courier-Bold". Usage: /usr/local/sbin/textfmt [-1] [-2] [-B] [-c] [-D] [-f fontname] [-F fontdir(s)] [-m N] [-o #] [-p #] [-r] [-U] [-Ml=#,r=#,t=#,b=#] [-V #] files... >out.ps Default options: -f Courier -1 -p 11bp -o 0 Error converting document; command was "/usr/local/sbin/textfmt -B -f Courier-Bold -Ml=0.4in -p 11 -s default >'/tmp//sndfaxp5GdJ9' <'/etc/passwd'" It seems like there is problem with font problem. I have ghostscript-fonts installed too. I can't find hyla.conf in path /etc/hylafax. There is no /etc/hylafax path in my file system. All configuration files seems located in /var/spool/hylafax/etc. Please advice. Thank you.

  Read the article

• Poor NFS Performance: OpenFiler

  - by Safin09

  Good Day Everyone, I have an issue with OpenFiler, a Linux-based operating that converts a computer system into a SAN/NAS appliance. Here is the problem. In my environment we have two Netapp Storevault 500 appliances that I normally perform backups to a NFS share. There are two backup cronjobs that use ghettoVCB to backup two groups of VM's. One group is a pool of 3 VMs. This takes 13 mins to complete. A second job that backups a pool of 5 VMs to a 2nd Storevault appliance which takes 2 hours. We then installed Openfiler on a old server that has 2 core Xeon processors. There is a software RAID 5 process in place. When performing the same backups to a NFS Openfiler share, the first backup job, which takes 13 mins, takes around 4 hours. The second backup job, which takes 2 hours, takes almost 10 hours to complete. This is unacceptable!!!! Especially considering the strain placed on the host ESX Server. I assumed that because of the software RAID 5, the overhead on the CPU explained the long backup times. I then installed Openfiler on a 2nd server, an IBM x306 machine which has a P4 Intel processor. This time no software RAID or any RAID at all. A single 750GB hard drive that contained the OS and the rest of the disk uses to backup VMs to a NFS share. I performed the first backup job of the pool of 3 VMs. This time the backup job took 1 and 1/2 hours to complete instead of 13 mins!!!!!!!!!! Is Openfiler simply poor at being an NFS Server!!!!!!!!!!!!! Has anyone else had these issues with Openfiler?

  Read the article

• Mac Management and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• Maximum RAM on Biostar P4M8PM7 Socket775 mATX board

  - by Alex Balashov

  I have a server with a Biostar P4M8PM7 ("Pro-M7") board based on a VIA chipset. It's a strange board to put in a server because it seems like more of a desktop board to me, but alas! It takes DDR2-667 (PC5300) RAM. What I can't figure out is the maximum amount I can put in it, as I cannot find the manual anywhere online. I've found a few marketing broadsheets from online retailers that say, "up to 2 GB of RAM!" but I am not sure whether to believe them. They also do not seem to be quite for the same board, as they indicate DDR2 400/533 RAM, for example: http://www.geeks.com/details.asp?invtid=P4M8P-M7. The manufacturer's web site says the same thing, but does not elaborate. It's a 64-bit CPU and board; is there a technical reason why the board would not be able to address more than 2 GB? Can someone tell me what sort of that reason that would be? I bought this server from someone really hoping I could put 8 to 16 in it, and wanted to do some research before I gave up. On a related note, it's not indicated anywhere whether it can take ECC RAM; the existing chips are not ECC, but most memory sold in the range I'm looking for (e.g. DIMMs with enough chip density to do 8 GB) seems to be server-class and for that reason ECC. Any ideas? Thank you very much for your consideration in advance!

  Read the article

• data is not posted in $_POST variable using AJAX [migrated]

  - by Oliver

  Im having a problem in one of my script. Server is running in php, and im using AJAX to post data. Here is my script. PHP script: 0){ echo "Search Result :"; for ($x=0;$xProject Name:   ".mysql_result($result,$x,"projname").""; echo "APMS ID:   ".mysql_result($result,$x,"apmsid").""; echo "Prefix/es:   ".mysql_result($result,$x,"projprefix").""; echo "Usage Type:   ".mysql_result($result,$x,"usagetype").""; echo "Rate:   ".mysql_result($result,$x,"projrate").""; echo "Offer Details:   ".mysql_result($result,$x,"offerdetails").""; } }else{ echo "No results found ..."; } }else{ echo "Problems encountered while processing the data ..."; } ? JS Script: function QueryPrefix() { var xmlhttp; var pStr = document.getElementById('Editbox2'); var htmlHolder = document.getElementById('Html1'); var butStr = document.getElementById('Button1'); if (pStr.value.length == 0){ alert("Please enter a value on the box provided!"); return; } pStr.value=""; if (window.XMLHttpRequest) {// code for IE7+, Firefox, Chrome, Opera, Safari xmlhttp=new XMLHttpRequest(); } else {// code for IE6, IE5 xmlhttp=new ActiveXObject("Microsoft.XMLHTTP"); } xmlhttp.onreadystatechange=function() { if (xmlhttp.readyState==4) { htmlHolder.innerHTML=xmlhttp.responseText; butStr.disabled=false; } } butStr.disabled=true; xmlhttp.open("POST","searchutype.php",false); xmlhttp.setRequestHeader("Content-type","application/x-www-form-urlencoded"); xmlhttp.send("pStr=" + pStr.value); }

  Read the article

• Bacula v5.0.2 Windows Installation Issues

  - by JohnyD

  First off, I am very new to Bacula but I'm very intriqued from what I've read. I'm looking to set up Bacula 5.0.2 on a Windows 2008 R2 server. I've run the installer and at the end it asks me to configure DIR name, DIR password, DIR Address. Windows documentation is somewhat hard to come by and I'm not certain what exactly I'm supposed to enter here. Do I need to create a local account that matches this info? Will the installation process create the account for me? Will this be the account that handles the FD daemon/service? I'm also not certain if Address means network location or local direcory. I apologize for my ignorance. Currently I'm trying to use the following information: Name: john pass: john address: thin1 (server name although I have also tried thin1.fqdm.local and 10.0.0.104) This info allows for the installer to complete successfully. However, when I run the BAT it hangs at, "Connecting to Director thin1:9101". The Bacula File Service is currently running under the local system account. What am I doing wrong? What do I have yet to do? Once I get this working properly I assume I will need to install clients on all my Windows boxes? Also, this is a 64-bit cpu but I am installing the 32-bit client. Are there any issues with this? Should I be using the 32-bit client? Thanks very much for the help.

  Read the article

• process and memory issue on linux server

  - by zapping

  Need some assistance in analyzing apache and php process running on linux server. Its a 8-core intel processor with 4GB ram. When the website on it runs the top displays like this. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 23459 username1 16 0 151m 27m 8388 S 11.3 0.7 0:11.71 php5 23730 username1 16 0 151m 28m 8388 S 11.3 0.7 0:03.87 php5 23458 username1 16 0 151m 28m 8388 S 3.0 0.7 0:19.20 php5 16202 mysql 15 0 459m 38m 4624 S 0.7 1.0 62:33.81 mysqld 24141 nobody 15 0 311m 5832 2304 S 0.3 0.1 0:00.03 httpd Why does the command say php5 when the website is accessed. Both apache and php was preconfigured so not sure whats done there. Tried setting up the same site and db on a different server but on it the process shows httpd always and not php5. The site uses mysql db. The problem is server load seems to go till about 5.x when the website was access by about 16users. When the free -m command was given the output shows total used free shared buffers cached Mem: 3941 3727 213 0 236 2734 -/+ buffers/cache: 756 3184 Swap: 4095 0 4095 Lots of memory seems to be in cache and free memory is less. Even when the website is not accessed that is leaving it very much idle for about 2days the free memory showed just 190. When the site is accessed the free memory seems to be go till 90mb then it increases to about 150mb. It always seems to remain just about 200mb. Is it somehow related to the server load showing 5.x. Will adding some more RAM resolve the load issue?

  Read the article

• Munin node not listing any plugins on new Fedora 14 installation

  - by Dave Forgac

  I have just installed munin-node from the base repo on Fedora 14 and then started it. I found that my munin server is not able to collect data from this node so I tried connecting via telnet to test. When connecting via telnet I see that no plugins are listed: [dave@host ~]# telnet localhost 4949 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. # munin node at host.example.com list quit Connection closed by foreign host. [dave@host ~]# I did not modify anything after the installation. The munin-node.conf is allowing connections from 127.0.0.1 and the default set of plugins in /etc/munin/plugins/ are symlinked to the plugins in /usr/share/munin/plugins/. Here is the working output of the telnet test of the 'list' command should look like (this is on a Fedora 13 host): [dave@www ~]$ telnet localhost 4949 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. # munin node at www.example.com list apache_accesses apache_processes apache_volume cpu df df_inode entropy forks fw_packets if_err_eth0 if_err_eth1 if_eth0 if_eth1 interrupts iostat iostat_ios irqstats load memory munin_stats mysql_ mysql_bytes mysql_innodb mysql_queries mysql_slowqueries mysql_threads netstat open_files open_inodes postfix_mailqueue postfix_mailvolume proc_pri processes swap threads uptime users vmstat yum quit Connection closed by foreign host. [dave@www ~]$ Edited to show output of munin-node-configure: [root@host ~]# munin-node-configure Plugin | Used | Extra information ------ | ---- | ----------------- acpi | no | amavis | no | ... http_loadtime | no | if_ | yes | eth1 eth0 if_err_ | yes | eth0 eth1 ifx_concurrent_sessions_ | no | interrupts | yes | ... uptime | yes | users | yes | varnish_ | no | vserver_resources | no | yum | yes | zimbra_ | no | Any suggestions on what to check next?

  Read the article

• nginx does not use variables set in /etc/environment on system reboot, but does when restarted from shell

  - by Dave Nolan

  I have a Rails app running on nginx/passenger. It restarts happily in a shell using sudo /etc/init.d/nginx stop|start|restart. But Passenger throws an error when the system is rebooted: "Missing the Rails #{version} gem". But GEM_HOME and GEM_PATH are both set in /etc/environment so surely they would be available to all processes during reboot? /etc/environment PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/bin/X11:/usr/games" GEM_HOME=/var/lib/gems/1.8 GEM_PATH=/var/lib/gems/1.8 /etc/init.d/nginx #! /bin/sh ### BEGIN INIT INFO # Provides: nginx # Required-Start: $all # Required-Stop: $all # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts the nginx web server # Description: starts nginx using start-stop-daemon ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin DAEMON=/opt/nginx/sbin/nginx NAME=nginx DESC=nginx test -x $DAEMON || exit 0 # Include nginx defaults if available if [ -f /etc/default/nginx ] ; then . /etc/default/nginx fi set -e case "$1" in start) echo -n "Starting $DESC: " start-stop-daemon --start --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON -- $DAEMON_OPTS echo "$NAME." ;; stop) echo -n "Stopping $DESC: " start-stop-daemon --stop --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON echo "$NAME." ;; restart|force-reload) echo -n "Restarting $DESC: " start-stop-daemon --stop --quiet --pidfile \ /var/log/nginx/$NAME.pid --exec $DAEMON sleep 1 start-stop-daemon --start --quiet --pidfile \ /var/log/nginx/$NAME.pid --exec $DAEMON -- $DAEMON_OPTS echo "$NAME." ;; reload) echo -n "Reloading $DESC configuration: " start-stop-daemon --stop --signal HUP --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON echo "$NAME." ;; *) N=/etc/init.d/$NAME echo "Usage: $N {start|stop|restart|force-reload}" >&2 exit 1 ;; esac exit 0 $ opt/nginx/sbin/nginx -v nginx version: nginx/0.7.67 Ubuntu lucid

  Read the article

• ZFS - destroying deduplicated zvol or data set stalls the server. How to recover?

  - by ewwhite

  I'm using Nexentastor on a secondary storage server running on an HP ProLiant DL180 G6 with 12 Midline (7200 RPM) SAS drives. The system has an E5620 CPU and 8GB RAM. There is no ZIL or L2ARC device. Last week, I created a 750GB sparse zvol with dedup and compression enabled to share via iSCSI to a VMWare ESX host. I then created a Windows 2008 file server image and copied ~300GB of user data to the VM. Once happy with the system, I moved the virtual machine to an NFS store on the same pool. Once up and running with my VMs on the NFS datastore, I decided to remove the original 750GB zvol. Doing so stalled the system. Access to the Nexenta web interface and NMC halted. I was eventually able to get to a raw shell. Most OS operations were fine, but the system was hanging on the zfs destroy -r vol1/filesystem command. Ugly. I found the following two OpenSolaris bugzilla entries and now understand that the machine will be bricked for an unknown period of time. It's been 14 hours, so I need a plan to be able to regain access to the server. http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6924390 and http://bugs.opensolaris.org/bugdatabase/view_bug.do;jsessionid=593704962bcbe0743d82aa339988?bug_id=6924824 In the future, I'll probably take the advice given in one of the buzilla workarounds: Workaround Do not use dedupe, and do not attempt to destroy zvols that had dedupe enabled. Update: I had to force the system to power off. Upon reboot, the system stalls at Importing zfs filesystems. It's been that way for 2 hours now.

  Read the article

• ASUS P8B WS - Endless Reboots

  - by tuxGurl

  I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

  Read the article

< Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >