Search Results

Search found 9845 results on 394 pages for 'xbox controller'.

Page 329/394 | < Previous Page | 325 326 327 328 329 330 331 332 333 334 335 336  | Next Page >

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• Low-profile, PCI Express, x1 video card with VGA-out?

  - by Dandy

  I just bought an Acer Aspire EasyStore H340 system (http://us.acer.com/acer/productv.do?LanguageISOCtxParam=en&kcond61e.c2att101=54825&sp=page16e&ctx2.c2att1=25&link=ln438e&CountryISOCtxParam=US&ctx1g.c2att92=450&ctx1.att21k=1&CRC=936243954) It comes with Windows Home Server, which I don't particularly care for (too dumbed down for my liking)--I bought the box mainly for the form factor, and intend to install Server 2008 on it and have it run as a small domain controller. The geniuses at Acer however went out of their way to ensure you can only run Home Server--you can only connect to it via the Home Server Connector software, as it has no video-out whatsoever (so essentially, there's no way to even get into the BIOS). It only has a low-profile, PCI Express x1 slot. It turns out to be way harder than I thought to locate a video card that both has an x1 connector, and is low-profile (I'd really rather not snip the bracket at the back just so it'll fit the case). I know they're out there, and I've seen one with Display Port outputs, but I don't have a monitor with this connection. So to reiterate, it needs to be: - x1 connector - low profile - VGA out (though DVI would be okay; I have some spare adapters) Can anyone recommend anything at all?

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Western Digital HDD disappears and reappears in BIOS

  - by tbkn23

  I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• How can I pair two bluetooth dongles together?

  - by techaddict

  I want to hack a device which connects via USB, and plug a bluetooth USB dongle to the end of the USB cable (using a female to female adapter), and then connect to that device from another USB bluetooth dongle connected to my computer. How can I do this? It is straightforward? I don't want to spend $30 before I know how to do this. Also I think another concern is that the USB cable is providing power to the device. So I think that means I would also have to hack it for power. I have created this diagram in Photoshop to illustrate my intent: (NOTE: it won't be a USB mouse, as that would be pointless because there are already wireless mice in existence. The mouse is displayed for illustrative purposes) Don't tell me "it won't work". Because I KNOW it WILL work. Think for example, PS3 controller. That works, and in fact I was able to get it working with my laptop, over bluetooth. I just want to know HOW to make it work.

  Read the article

• RAID 6 that can read with least 1000 Mbit/s?

  - by Diblo Dk

  I purchased a Dell PERC 6/i which I expected to be able to read with 1000 Mbps. There is not much to do now, but there are some things I wanted knowledge about for another time. I have configured it with four 2 TByte drives and RAID 6. It have 256 MByt ram and transfer rate of 300 Mbps. The benchmark test showed: Min read rate: 136.3 Mbps Max read rate: 329,6 Mbps Avg read rate: 242,2 Mbps What could I had done to get at least 1000 Mbps? Is it normal for internal and external RAID controllers to have a lower transfer rate eg. 300 Mbps? (I did not noticed at the time that it was not 3 Gbps) How would a RAID 10 had performed compared to RAID 6 or 5? Would it have been better to use software RAID (Linux) with the internal 3 Gbps SATA controller? UPDATE: The drives is SATA III 6 Gbps. http://www.seagate.com/files/staticfiles/docs/pdf/datasheet/disc/desktop-hdd-data-sheet-ds1770-1-1212us.pdf (2TB)

  Read the article

• I need to preserve a tape using symantec backup exec. I'm aving trouble doing so

  - by MrVimes

  Please forgive me if this is the wrong stack exchange site. Please suggest which one I should post this to if it is. There's an automatic tape machine running in a remote location, with software (symantec backup exec 11d) Recently one of the servers being backed up had problems with its raid controller, so one of the drives has become invisible. I need to preserve the last good backup of that drive so I am trying to replace the tape with the most recent backup of that drive on it with one of the scratch tapes (blank tapes) present in the machine. I've tried the following... Associate the blank media with the media set in question (Wednesday) For the existing media (the tape with the data I want to keep) I click 'move to vault' and move it to the offline vault. I associate it with something other than 'Wednesday' (a media set called 'keep data infinitely...') I then do an inventory on that slot. The above steps I'm led to believe are supposed to put the fresh tape in the slot that had the tape I want to keep in it. But it just keeps showing up as containing the tape I want to keep after the inventory. (after refreshing the device tree) I am a complete newbie with this software. Can you tell me what I'm doing wrong, and/or tell me how to acheive my desired goal Edit: Just want to point out that I did try to get help directly from symantec with this, but having jumped through countless hoops to create an account and create a support ticket my progress was halted by requiring something called a 'tecnical contact id' at the final step with no explanation of what it is or how to get one.

  Read the article

• No sound out of headphone port

  - by Thanatos

  I cannot get sound out of the headphone port. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller

  Read the article

• Uninstallation of WSUS form SBS 2008

  - by Logik

  I am not much experienced system admin, but i came across the client who was having SBS 2008. The server was running out of HDD space. So to recover some, I removed its WSUS role (twas not needed).this removed WSUS 3.0 SP1 & freed a lot of space. This SBS is: Domian controller, DNS, DHCP, File server. After i removed WSUS i disabled windows update service & i rebooted serer & checked from one of client if the shared folders are accessible. they were. Next day all of sudden i got call from them saying they can't login into their domain. I looked into server, the Active directory service was stopped. I never remember touching any service other than windows update. How come AD service stopped running all of sudden. Is removing WSUS have such impact? I am not aware of any such thing.

  Read the article

• Adding more drives to a drive array

  - by Mystere Man

  I have a friend who has two servers, a Dell 1800 and an HP 350 ML G5, both have SAS drive arrays. The Dell is a 3.5" and the HP is a 2.5". They currently only have 3 drives in each array. We want to add additional drives, but they do not appear to have caddies, just "fake" covers. I haven't been able to take a good look at them, so I'm not sure what I need to do here. Are the "sockets" just there, and I can buy additional caddies and just stick them in? Or do I have to buy some kind of caddy adapter? Also, i'm thinking of just going 2.5" in the new server, so is there a 2.5" adapter caddy that will fit in the 3.5" chassis for the Dell, so I can use 2.5" drives in the 3.5" chassis? Can I buy 6GB/s drives and add them to the 3GB/s controller? The reason is that we're going to replace both computers in a year or so, and we want to bring the drives with. So rather than buy 3GB/s drives, we just want to buy 6GB/s drives so they can be used in the new server.

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• RAID-capable 3.5" SATA Drives

  - by nroam

  I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

  Read the article

• In Windows 7 power management, is it possible to set different sleep settings for different SATA disks?

  - by Ben Voigt

  I'm having an issue with Windows 7 either freezing up or generating a BSOD coming out of sleep. I suspect that it is related to my boot/OS drive, an OCZ Vertex SE SSD, because numerous other Vertex users have reported sleep problems. Notably, if I put the computer to sleep, it almost always wakes correctly. If it goes to sleep after a timeout, it almost always BSODs. I disabled timed sleep and now it freezes when left unattended. My next step is to disable "Put hard disks to sleep after X minutes", but I'd like to change this setting only for the SSD and not for the rotating data disks, which I would like to spin down normally. Does anyone know a place to configure sleep on a per-disk basis? I don't need to set different timeouts on different disks (although that would be nice), simply setting "this disk sleeps" and "sleep is disabled for this disk" would be great. Additional system information: Windows 7 Ultimate x64, Core i5 - P55 chipset, Intel RST drivers are installed. One SSD, two rotating HDD, and a DVD-RW drive are all connected to the Intel SATA ports. I could potentially move some of these to my motherboard's other SATA controller if that would help.

  Read the article

• Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

  - by Alex

  We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks.

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• LSI1068E hidden drives after failed raid volume creation

  - by silk

  We are using LSI 1068E raid chipset with SAS drives. We had added new drives to the system, and tried to create new raid volume with the lsiutil, unfortunately the creation failed. The problem is that now we do not have the new raid volume and disks 'disappeared' and are not available as targets for raid. Lsiutil option 8 (scan for devices) does not display these disks at all. lsiutil option 16 (display attached devices) does list them as targets. lsiutil option 21+30 (create raid) does not list these disks. Just after insrting them to enclosure these disks appeared in the system, as expected. During the raid creation kernel logged: Mar 4 08:40:02 kilo kernel: [57555.687946] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 2 id=0 Mar 4 08:40:02 kilo kernel: [57555.687978] mptbase: ioc0: PhysDisk has been created Mar 4 08:40:02 kilo kernel: [57555.695438] scsi target0:0:2: mptsas: ioc0: RAID Hidding: fw_channel=0, fw_id=0, physdsk 2, sas_addr 0x5000c50008ebe5fd for both of them, again as expected. Unfortunately they did not appear back even though the volume was not created. The same situation is in the controller's bios after a reboot. Taking the disks out and inserting in different slots did not help, either. Has someone seen a similar problem? And knows how to 'get back' our disks?

  Read the article

• Hyper-V and attaching physical disks

  - by Mike Christiansen

  So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

  Read the article

• Hyper-V and attaching physical disks [migrated]

  - by Mike Christiansen

  So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

  Read the article

• Problem with setting up RAID 5 on FreeNAS

  - by Benjy23

  I've been running FreeNAS for a while now. Hardware is 1.8 GHz Celeron, RAM 1 GB. SATA card is Via - I am not sure about the model. It's 2 ports and I have 6 x 1.5 TB hard drives. All ran OK while running on 1.5 TB, no RAID. I'm now trying to create a RAID 5 with my 6 hard drives. Software RAID. Is it normal for it to take roughly up to 2 weeks just to build the RAID? Sorry, I'm very new to implementing RAID and googling doesn't tell much other than it takes a long time. Also the RAID building process seems to fail many times. Going to degraded. I suspect it's because 4 of my hard drives are connected to my motherboard and the other 2 are connected to my SATA card. What's your take? I'm considering 2 options now. Either get a 8 port SATA card and attach all the hard drives to it. Or get a RAID controller 8 portcard which is probably going to be more pricey. Also how do you access hardware RAID through FreeNAS? I like how FreeNAS emails you should your harddrive fails. Can this be done as well with hardware RAID?

  Read the article

• What does the 'Burst Rate' stat mean in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks

  Read the article

• Why is my global security group being filtered out of my logon token?

  - by Jay Michaud

  While investigating the effects of filtered tokens on my file permissions, I noticed that one of my global security groups is being filtered in addition to the regular system-defined filtered groups. My Active Directory environment is a single-domain forest on the Windows Server 2003 functional level. I'll call the domain "mydomain.example.com". I am logged onto a Windows Server 2008 Enterprise Edition machine (not a domain controller) as a member of the "MYDOMAIN\Domain Admins" group and the "MYDOMAIN\MySecurityGroup" global security group (among others). When I run "whoami /groups" from an elevated command prompt, I see the full list of groups to which my account belongs as expected. When I run "whoami /groups" from a regular, non-elevated command prompt, I see the same list of groups, but the following groups are described as "Group used for deny only". BUILTIN\Administrators MYDOMAIN\Schema Admins MYDOMAIN\Offer Remote Assistance Helpers MYDOMAIN\MySecurityGroup Numbers 1 through 3 above are expected based on Microsoft documentation; number 4 is not. The "MYDOMAIN\MySecurityGroup" global security group is a group that I created. It contains three non-built-in global security groups, and these security groups contain only non-built-in user accounts. (That is, I created all of the accounts and groups that are members of the "MYDOMAIN\MySecurityGroup" global security group.) There are other, similar groups of which my account is a member that are not being filtered out of my logon token, and this group is not granted any specific user rights in the security settings of this computer or in Group Policy. What would cause this one group to be filtered out of my logon token?

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• Creating a Logical network diagram

  - by user273284

  Im a student and I have been assigned the task of creating a logical network diagram for the following scenario There are 2 buildings, the first is the head office and the second is the branch. The data centre is in the head office, it contains domain controller, mail server, file server and a web server. it provides wired and wireless access to the staff. the branch building is new and it does not have a network. The two buildings must be connected using a VPN connection. The branch building will not have any servers but just network devices that will provide the connectivity, the users in the branch building will be connected to the head office over the VPN. I had created a diagram based on this scenario, but my teacher rejected it saying that it does not follow Cisco hierarchical Model and the servers were not placed correctly in the diagram. I just wanted some help in this matter so that I Can create my network diagram correctly. If anyone could upload a picture of how the logical diagram should be for this scenario will be helpful, any other resources would also be great.

  Read the article

• Revamping an old and unstable office IT-solution using Windows Server and OpenVPN

  - by cmbrnt

  I've been given the cumbersome task to totally redo the IT-infrastructure for a customer's office. They are currently running Windows XP all over, with one computer acting as a file server with no control over which users have access to which files, and so on. To top it off, this file server also functions as a workstation, which means it gets rebooted every time the user notices some sluggish behavior or experiences problems with flash games. To say the least, this isn't working for them. Now - I've got a very slim budget, but I need to set up a new server, and I wish to run Windows Server 2008 on it. I also need the ability to access the network remotely via VPN. Would it be a good idea to install VMware ESXi 4.1 onto the new server, and then run Windows Server 2008 as well as a separate Debian install for openvpn on it? I don't like the Domain Controller for the future AD to also run a VPN-server, because of stability issues when something goes to hell with either of them. There will be no redundancy though. However, I'm not sure if there is something to gain by installing a VPN solution on the Windows Server itself, when it comes to accessing file shares on the network via VPN. I don't know how to enable users logging in via the VPN to access the remote files, since they will be accessing the network from their own home computers (which is indeed a really bad idea, but this is what I've got to work with). They won't be logged in to the windows Domain, but rather their home workgroups. I need to be able to grant access to files in certain directories based on the logged in AD-user, but every computer won't necessarily be configured to log into the domain. I'm not sure how to explain this in a good way, but I'd be happy to clarify if somethings not clear. Any help would be great, because I've got a feeling that I can't do this without introducing a bunch of costly new rules when it comes to their IT-solution. I'd rather leave that untouched and go on my merry way to the next assignment.

  Read the article

< Previous Page | 325 326 327 328 329 330 331 332 333 334 335 336  | Next Page >