Search Results

Search found 5520 results on 221 pages for 'compound primary'.

Page 33/221 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

  • linksys Rvo16 redundant link config

    - by Adeodatus
    Hi All I have been given an RVO16 to play with. I'm multihomed and I'd like to set it up so that my primary, highest bandwidth link receives all traffic and the other connection is a hot spare basically. I want them both online but only the primary 1 used until it goes down then all traffic should automatically failover to the secondary link. Those of you that have played on an RVO16, can I do this and if so, how? I imagine I'd have it act as a router and pad the route on one so that the other is never used unless the primary is down. How? Thanks all.

    Read the article

  • Cannot create a new domain in an existing active directory forest

    - by Mackenzie Carr
    I have a domain controller setup on Windows Server 2008 R2 (Forest) and I have another Windows Server 2008 R2 (New Domain) and I want to create a new domain in an existing forest. I get the following error: An Active Directory domain controller for the domain mackdev.mackenziecarr.com could not be contacted The error was "no records found for the given DNS query" The query was for the SRV record for: _ldap._tcp.dc._msdcs.mackdev.mackenziecarr.com I've seem to have tried everything even tried adding this record to the DNS server of the primary forest. I even successfully joined this server to the domain without any issues but trying to create a new domain under the existing forest is no luck. The primary forest I.P. address is 192.168.2.20 the server that I am using to try to make a child domain is 192.168.2.21 My ipconfig are as follows: I.P. Address: 192.168.2.21 Subnetmask: 255.255.255.0 Gateway: 192.168.2.1 Primary DNS: 192.168.2.20

    Read the article

  • DFS replication initial step problem

    - by vn
    Heya, I just setup DFS on my network and it's working fine, and now I'm trying to setup DFS-R on a test folder, but then at the end of the procedure (all went fine, selected my 2 folders, primary folder, replication topology and such) I get this error message (roughly translated from french) : Unable to define security on the replicated folder. The shared administration folder doesn't exist. I'm also wondering if there's any required security on the folders to replicate so that DFS-R can access it. I was trying to add SYSTEM in the security, but it won't find it/allow me. The folder has many many files and folders on the primary DFS pointer, but none on the 2nd, just created it with quite the same rights. Note that the primary DFS pointer is on a 2008 server and the DFS service and the secondary DFS pointer are on a 2008r2. Any help is very appreciated, thanks.

    Read the article

  • MySQL "ERROR 1005 (HY000): Can't create table 'foo.#sql-12c_4' (errno: 150)"

    - by Ankur Banerjee
    Hi, I was working on creating some tables in database foo, but every time I end up with errno 150 regarding the foreign key. Firstly, here's my code for creating tables: CREATE TABLE Clients ( client_id CHAR(10) NOT NULL , client_name CHAR(50) NOT NULL , provisional_license_num CHAR(50) NOT NULL , client_address CHAR(50) NULL , client_city CHAR(50) NULL , client_county CHAR(50) NULL , client_zip CHAR(10) NULL , client_phone INT NULL , client_email CHAR(255) NULL , client_dob DATETIME NULL , test_attempts INT NULL ); CREATE TABLE Applications ( application_id CHAR(10) NOT NULL , office_id INT NOT NULL , client_id CHAR(10) NOT NULL , instructor_id CHAR(10) NOT NULL , car_id CHAR(10) NOT NULL , application_date DATETIME NULL ); CREATE TABLE Instructors ( instructor_id CHAR(10) NOT NULL , office_id INT NOT NULL , instructor_name CHAR(50) NOT NULL , instructor_address CHAR(50) NULL , instructor_city CHAR(50) NULL , instructor_county CHAR(50) NULL , instructor_zip CHAR(10) NULL , instructor_phone INT NULL , instructor_email CHAR(255) NULL , instructor_dob DATETIME NULL , lessons_given INT NULL ); CREATE TABLE Cars ( car_id CHAR(10) NOT NULL , office_id INT NOT NULL , engine_serial_num CHAR(10) NULL , registration_num CHAR(10) NULL , car_make CHAR(50) NULL , car_model CHAR(50) NULL ); CREATE TABLE Offices ( office_id INT NOT NULL , office_address CHAR(50) NULL , office_city CHAR(50) NULL , office_County CHAR(50) NULL , office_zip CHAR(10) NULL , office_phone INT NULL , office_email CHAR(255) NULL ); CREATE TABLE Lessons ( lesson_num INT NOT NULL , client_id CHAR(10) NOT NULL , date DATETIME NOT NULL , time DATETIME NOT NULL , milegage_used DECIMAL(5, 2) NULL , progress CHAR(50) NULL ); CREATE TABLE DrivingTests ( test_num INT NOT NULL , client_id CHAR(10) NOT NULL , test_date DATETIME NOT NULL , seat_num INT NOT NULL , score INT NULL , test_notes CHAR(255) NULL ); ALTER TABLE Clients ADD PRIMARY KEY (client_id); ALTER TABLE Applications ADD PRIMARY KEY (application_id); ALTER TABLE Instructors ADD PRIMARY KEY (instructor_id); ALTER TABLE Offices ADD PRIMARY KEY (office_id); ALTER TABLE Lessons ADD PRIMARY KEY (lesson_num); ALTER TABLE DrivingTests ADD PRIMARY KEY (test_num); ALTER TABLE Applications ADD CONSTRAINT FK_Applications_Offices FOREIGN KEY (office_id) REFERENCES Offices (office_id); ALTER TABLE Applications ADD CONSTRAINT FK_Applications_Clients FOREIGN KEY (client_id) REFERENCES Clients (client_id); ALTER TABLE Applications ADD CONSTRAINT FK_Applications_Instructors FOREIGN KEY (instructor_id) REFERENCES Instructors (instructor_id); ALTER TABLE Applications ADD CONSTRAINT FK_Applications_Cars FOREIGN KEY (car_id) REFERENCES Cars (car_id); ALTER TABLE Lessons ADD CONSTRAINT FK_Lessons_Clients FOREIGN KEY (client_id) REFERENCES Clients (client_id); ALTER TABLE Cars ADD CONSTRAINT FK_Cars_Offices FOREIGN KEY (office_id) REFERENCES Offices (office_id); ALTER TABLE Clients ADD CONSTRAINT FK_DrivingTests_Clients FOREIGN KEY (client_id) REFERENCES Clients (client_id); These are the errors that I get: mysql> ALTER TABLE Applications ADD CONSTRAINT FK_Applications_Cars FOREIGN KEY (car_id) REFERENCES Cars (car_id); ERROR 1005 (HY000): Can't create table 'foo.#sql-12c_4' (errno: 150) I ran SHOW ENGINE INNODB STATUS which gives a more detailed error description: ------------------------ LATEST FOREIGN KEY ERROR ------------------------ 100509 20:59:49 Error in foreign key constraint of table practice9/#sql-12c_4: FOREIGN KEY (car_id) REFERENCES Cars (car_id): Cannot find an index in the referenced table where the referenced columns appear as the first columns, or column types in the table and the referenced table do not match for constraint. Note that the internal storage type of ENUM and SET changed in tables created with >= InnoDB-4.1.12, and such columns in old tables cannot be referenced by such columns in new tables. See http://dev.mysql.com/doc/refman/5.1/en/innodb-foreign-key-constraints.html for correct foreign key definition. ------------ I searched around on StackOverflow and elsewhere online - came across a helpful blog post here with pointers on how to resolve this error - but I can't figure out what's going wrong. Any help would be appreciated!

    Read the article

  • Cluster failover and strange gratuitous arp behavior

    - by lazerpld
    I am experiencing a strange Windows 2008R2 cluster related issue that is bothering me. I feel that I have come close as to what the issue is, but still don't fully understand what is happening. I have a two node exchange 2007 cluster running on two 2008R2 servers. The exchange cluster application works fine when running on the "primary" cluster node. The problem occurs when failing over the cluster ressource to the secondary node. When failing over the cluster to the "secondary" node, which for instance is on the same subnet as the "primary", the failover initially works ok and the cluster ressource continues to work for a couple of minutes on the new node. Which means that the recieving node does send out a gratuitous arp reply packet that updated the arp tables on the network. But after x amount of time (typically within 5 minutes time) something updates the arp-tables again because all of a sudden the cluster service does not answer to pings. So basically I start a ping to the exchange cluster address when its running on the "primary node". It works just great. I failover the cluster ressource group to the "secondary node" and I only have loss of one ping which is acceptable. The cluster ressource still answers for some time after being failed over and all of a sudden the ping starts timing out. This is telling me that the arp table initially is updated by the secondary node, but then something (which I haven't found out yet) wrongfully updates it again, probably with the primary node's MAC. Why does this happen - has anyone experienced the same problem? The cluster is NOT running NLB and the problem stops immidiately after failing over back to the primary node where there are no problems. Each node is using NIC teaming (intel) with ALB. Each node is on the same subnet and has gateway and so on entered correctly as far as I am concerned. Edit: I was wondering if it could be related to network binding order maybe? Because I have noticed that the only difference I can see from node to node is when showing the local arp table. On the "primary" node the arp table is generated on the cluster address as the source. While on the "secondary" its generated from the nodes own network card. Any input on this? Edit: Ok here is the connection layout. Cluster address: A.B.6.208/25 Exchange application address: A.B.6.212/25 Node A: 3 physical nics. Two teamed using intels teaming with the address A.B.6.210/25 called public The last one used for cluster traffic called private with 10.0.0.138/24 Node B: 3 physical nics. Two teamed using intels teaming with the address A.B.6.211/25 called public The last one used for cluster traffic called private with 10.0.0.139/24 Each node sits in a seperate datacenter connected together. End switches being cisco in DC1 and NEXUS 5000/2000 in DC2. Edit: I have been testing a little more. I have now created an empty application on the same cluster, and given it another ip address on the same subnet as the exchange application. After failing this empty application over, I see the exact same problem occuring. After one or two minutes clients on other subnets cannot ping the virtual ip of the application. But while clients on other subnets cannot, another server from another cluster on the same subnet has no trouble pinging. But if i then make another failover to the original state, then the situation is the opposite. So now clients on same subnet cannot, and on other they can. We have another cluster set up the same way and on the same subnet, with the same intel network cards, the same drivers and same teaming settings. Here we are not seeing this. So its somewhat confusing. Edit: OK done some more research. Removed the NIC teaming of the secondary node, since it didnt work anyway. After some standard problems following that, I finally managed to get it up and running again with the old NIC teaming settings on one single physical network card. Now I am not able to reproduce the problem described above. So it is somehow related to the teaming - maybe some kind of bug? Edit: Did some more failing over without being able to make it fail. So removing the NIC team looks like it was a workaround. Now I tried to reestablish the intel NIC teaming with ALB (as it was before) and i still cannot make it fail. This is annoying due to the fact that now i actually cannot pinpoint the root of the problem. Now it just seems to be some kind of MS/intel hick-up - which is hard to accept because what if the problem reoccurs in 14 days? There is a strange thing that happened though. After recreating the NIC team I was not able to rename the team to "PUBLIC" which the old team was called. So something has not been cleaned up in windows - although the server HAS been restarted! Edit: OK after restablishing the ALB teaming the error came back. So I am now going to do some thorough testing and i will get back with my observations. One thing is for sure. It is related to Intel 82575EB NICS, ALB and Gratuitous Arp.

    Read the article

  • reverse nslookup fails for single machine

    - by matt wilkie
    I have a computer on a windows Active Directory network for which reverse dns lookup fails. It doesn't matter which machine runs the lookup. The problem computer is a debian vm on a windows server 2003 host. >nslookup wiki.dept Server: primary.internal.domain.org Address: 192.111.222.44 Name: wiki.dept.internal.domain.org Address: 192.111.111.185 >nslookup 192.111.111.185 Server: primary.internal.domain.org Address: 192.111.222.44 *** primary.internal.domain.org can't find 192.111.111.185: Non-existent domain Contents of /etc/resolv.conf on the debian guest: nameserver 192.111.111.244 nameserver 192.111.222.44 search internal.domain.org What is wrong? how do I get ip-to-name resolution to work for this machine? Thank you.

    Read the article

  • Redhat cluster Vs Pacemaker Vs Gluster Vs Sheepdog

    - by chandank
    Changing the entire question as earlier one was very confusing. I have been exploring different clustering system to run Virtual machines on two different machines on LAN with high availability. Currently I am already using DRBD resource on two different machines on Primary/Secondary mode. In case the primary fails I manually promote the secondary to Primary and start the VM. I also explored Gluster and looks good, however, I would rather prefer clustering over Gluster (user space FS). So if anyone has idea which one would be better from ease of use prospective please I would be interested in. Moreover, sheepdog project appears good, however, could not find much documentations/Howtos. I am using Centos 6.

    Read the article

  • Mouse Icon Distorted on Secondary Display

    - by Nathan Taylor
    I have a strange issue with a dual monitor, extended desktop setup where the mouse is always fine on the primary monitor, but sometimes when I move to the secondary display the icon becomes garbled and distorted (sometimes it just looks like a vertical line, instead of a pointer). If I move the mouse back and forth rapidly between primary and secondary displays the level of "garbledness" of the icon will change and sometimes go away completely. If I switch the display settings and set it to "Duplicate Monitor 1" then I end up with a garbled icon on the primary display and an accurate one on the secondary. Very annoying. Computer is Windows 7 Ultimate with an HD8750 and the newest video drivers. Monitors are two Dell 24" displays connected via DVI cables. I have also tried VGA cables.

    Read the article

  • Installing Solaris with Window. Disk partitioning problem.

    - by RishiPatel
    I am running windows and want to install the solaris but having hard time while using installer. I have 1 primary partition of 40GB and one extended partition. Extended partition have 4 logical drive. Solaris disk management window show only two partition one is of 40GB(Primary) and second is Extended partition. Can i convert a logical drive into primary partition( I have one free of 25 GB). Please look at the screenshot of disk management utitlity of window. http://img195.imageshack.us/img195/2005/20726948.jpg Is there any way to install solaris without reformatting the and repartitioning whole drive? In case it is not possible how should i partition and using which utility ?

    Read the article

  • DFS replication initial step problem

    - by vn.
    I just setup DFS on my network and it's working fine, and now I'm trying to setup DFS-R on a test folder, but then at the end of the procedure (all went fine, selected my 2 folders, primary folder, replication topology and such) I get this error message (roughly translated from french) : Unable to define security on the replicated folder. The shared administration folder doesn't exist. I'm also wondering if there's any required security on the folders to replicate so that DFS-R can access it. I was trying to add SYSTEM in the security, but it won't find it/allow me. The folder has many many files and folders on the primary DFS pointer, but none on the 2nd, just created it with quite the same rights. Note that the primary DFS pointer is on a 2008 server and the DFS service and the secondary DFS pointer are on a 2008r2. Any help is very appreciated, thanks.

    Read the article

  • Dual-WAN router

    - by aix
    I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

    Read the article

  • Create custom component based on LinearLayout, declaring layout in XML

    - by pheelicks
    I've been trying to create a Compound Control in Android 1.5 (as described here) but havn't been able to find any good examples on how to do this using an XML file to specify a layout. I'm fine with creating an Activity and then loading an xml file using the following in the constructor: setContentView(R.layout.main); However, I want to do this in subclass of LinearLayout - so I can use this compound component in other XML layouts. Something along the lines of: public class CustomView extends LinearLayout { public CustomView(Context context) { super(context); setupView(); } public CustomView(Context context, AttributeSet attrs) { super(context, attrs); setupView(); } public void setupView() { setContentView(R.layout.custom); // Not possible } } What is the correct way of going about doing this?

    Read the article

  • How do I make YouTube videos fill up the entire screen when using dual monitors?

    - by Jephir
    I am using a dual monitor setup on Ubuntu 9.10 using the TwinView configuration in NIVIDA X Server Settings. My total resolution is 2960x1050 pixels, and my individual monitors are 1680x1050 (primary) and 1280x1024 (secondary). When going into fullscreen mode on any video on YouTube, I only see a cropped version of the video on my primary display as seen below. This does not occur on any other video sharing website - they properly make the video to fill the entire screen on my primary monitor. To my knowledge this problem only happens on YouTube.

    Read the article

  • Servers at remote sites vs. centralized servers?

    - by Boden
    Looking for some opinions here. We've got three physical locations and site-to-site VPN between all three. Currently we've got Windows domain controllers at each location, with roughly 50 clients at each. The domains are currently separate, and we're looking at integrating the three sites. Email (Exchange) will be located at the primary site, and RPD is already being used at the secondary branches to hit the app servers also located at the primary site. The bulk of the local user load at the other two sites is just file sharing. What would the main benefits and drawbacks be of replacing the local domain controllers with NAS devices, and only keeping the domain controller(s) at the primary site? (assuming upgrades are coming regardless) Under what circumstances would you choose one setup over the other?

    Read the article

  • CentOS - Yum doesn't update anymore?

    - by Xanathos
    I've been trying to use yum now, but for some reason, not even the search work anymore. I even tried putting packages I already downloaded in the search criteria and is the same. [root@AMDFX03 Downloads]# yum search glibc Loaded plugins: fastestmirror, refresh-packagekit, security Loading mirror speeds from cached hostfile epel/metalink | 22 kB 00:00 * base: centos.secrel.com.br * epel: archive.linux.duke.edu * extras: centos.secrel.com.br * rpmforge: apt.sw.be * updates: centos.secrel.com.br adobe-linux-x86_64/primary | 1.2 kB 00:00 http://linuxdownload.adobe.com/linux/x86_64/repodata/primary.xml.gz: [Errno -1] Metadata file does not match checksum Trying other mirror. Error: failure: repodata/primary.xml.gz from adobe-linux-x86_64: [Errno 256] No more mirrors to try. This error always appear no matter what I do. Please, can you tell me how to fix this, or at least how to reset yum's configuration?

    Read the article

  • Will my RAID0 stay intact when I move it to a new computer?

    - by Jeremy H
    My primary drive is a 250GB WD SATA drive. So, I added 2x 500GB 7,200 RPM WD SATA drives into my Windows Vista box and created a 1TB RAID0. I then formatted the the primary drive and installed Windows 7. To my pleasant surprise when I booted into Windows 7 my RAID0 was still intact and I kept trotting along the same as I did before. Now I am replacing my motherboard, processor, and RAM and plan on formatting the primary 250GB drive again and using it to boot for a new clean install of Windows 7. My question is: if I move these two SATA drives which are setup for RAID0 into the new system, install Windows 7 again, will the RAID0 remain? Edit: Software RAID. I created it within Windows. The RAID0 does NOT contain the system boot partition.

    Read the article

  • How do I make YouTube videos fill up an entire screen when using dual monitors?

    - by Jephir
    I am using a dual monitor setup on Ubuntu 9.10 using the TwinView configuration in NIVIDA X Server Settings. My total resolution is 2960x1050 pixels, and my individual monitors are 1680x1050 (primary) and 1280x1024 (secondary). When going into fullscreen mode on any video on YouTube, I only see a cropped version of the video on my primary display as seen below. This does not occur on any other video sharing website - they properly make the video to fill the entire screen on my primary monitor. To my knowledge this problem only happens on YouTube.

    Read the article

  • Devices menu - project to second screen with only one monitor

    - by Jacob Palmer
    So I made a huge blunder. In the devices menu on Windows 8, I selected to project to a second screen only on accident. I had two monitors connected but only the primary one was actually displaying anything. So I projected it and now I can't access anything. The primary screen will show the windows icon when it loads, but then it disappears and I can't login or anything. Surely there's a way to get it back on the primary screen? Thanks a bunch. I'm really lost..

    Read the article

  • Dialogs appear on wrong monitor with SQL Server Management Studio 2008

    - by David
    I am running SSMS 2008 on Windows 7 with a dual monitor setup (one large, one small). SSMS is running on the secondary monitor, but everytime a dialog is opened, the dialog is placed on the primary monitor instead. I've tried moving the dialog over, closing it, and then re-opening it, but it doesn't remember and goes back to the primary monitor. This is really annoying for some of the designer dialogs, is there any way to fix this other than switching SSMS to the primary monitor? Is this a known bug with SSMS, or is it a problem with my particular setup?

    Read the article

  • Partition and mount my secondary hard drive on CentOS 5.5 64bit?

    - by Andrew Fashion
    I am trying to prepare my second hard drive for user image uploads. Here is the current layout: # sudo parted /dev/sda print Model: ATA WDC WD2500KS-00M (scsi) Disk /dev/sda: 250GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 107MB 107MB primary ext3 boot 2 107MB 8595MB 8488MB primary linux-swap 3 8595MB 10.7GB 2147MB primary ext3 4 10.7GB 250GB 239GB extended 5 10.7GB 250GB 239GB logical ext3 Information: Don't forget to update /etc/fstab, if necessary. I am assuming #4 is my secondary drive? How do I partition and mount it so I can begin using it? And how do I add to fstab? I understand if it's to many questions in one, just help me with whatever you can I guess :) Thank you for any help!

    Read the article

  • Freenas & LDAP Multiple User Groups Not Taking Affect

    - by Daniel Baker
    we are using, Freenas 9.2.1.7 which communicates with LDAP to control file permission. We have Windows users in multiple groups. Some belong to Finance as their primary group and Admin as another group they belong to. They can only access files from their Primary group. We use LDAP Account Manager - 4.4 to control which group the users belong to. We have also been trying to control access from the command line. We hae tried using this : setfacl -m group@:rwWxpaRc::allow DIR / Or File Name The problem is only the primary group is being seen / used. I am trying to determine why only on group is being used. Can someone please help me diagnose where the problem is. Thanks for the help, Dan

    Read the article

  • How to install Windows 8 boot manager in a different partition?

    - by arnab321
    the last time i installed Windows 7, the boot manager automatically got installed in a small hidden partition, and the main os into another partition. So, formatting the c: won't affect the boot manager. yesterday i wiped and repartitioned my hdd like this: 50mb primary ntfs (meant for boot manager) 100gb primary ntfs (for win 8) 50gb primary ntfs (for win 7) some logical partitions to install ubuntu and other os i installed win 7 and then win 8, and now there is no os choosing menu. system directly boots win 8 and the 50 mb partition is empty. There is a way to boot Windows 7 and even Ubuntu directly from the Windows boot manager with EasyBCD. But How do i put the boot manager in the 50mb partition ?

    Read the article

  • Is there a software in windows that enables you to boot from a specific partition?

    - by Tono Nam
    I use acronis true image to mount images to my primary partition and it works great. lets say I have 3 partitions on my hard disk and all of them each is 600 GB. In the 3rd partition I keep files (documents, pictures etc), on the first partition is my primary partition where the operating system runs (windows 7). And in the 2nd partition is empty. I have an image of my primary partition and I save that image in my 3rd partition (50 GB is the size of the image so it fits in the partition number 3) and in an external hard drive. I know it is possible to install a new operating system in partition 2 such as windows xp but the only problem is that once I install that how could I tell the computer to boot from partition 1? is there a way to switch back and forth just like it's possible in the mac?

    Read the article

  • How can I create a bootable CD-ROM/USB Drive? (With NTFS + USB Drive support)

    - by RonK
    My motherboard got fried and I was forced to get a new hardware set (MB+CPU+RAM) so in most likelyhood I'll need to reinstall my Windows 7. I usually follow procedure and put the OS on the primary partition and my data on a logical partition - so I can format the primary without concern - but this time I made a mistakte and left some crucial items on the primary partition. I want to create a bootable CD-ROM/USB Drive which can read NTFS so I can access this data. If booting via a CD-ROM, I would prefer being able to connect a disk-on-key/My Passport to the computer and be able to access it to transfer the data to it. How can I do it? (free 3rd party applications are most welcome)

    Read the article

  • How to generate JSON object on client side and send it to server?

    - by EugeneS
    I have ExtJS based application. I have compound object on the server side, and have ExtJS window with few tabs for editing different parts of this one object. For example: I Have Compound object "Car" public class Car { public string Name; public string Color; public List Wheels; public List Doors; } And on my ExtJS window i have tabs ("General Info", "Wheels", "Doors") for editing different parts of this object. So what i want: When i want to create a new car i want to generate JSON configuration for my class "Car" like {Name:null; Color:null; Wheels:[]; Doors:[]} then sent it to the client, fill it on the client (without callbacks to server) and after user finishes creating his Car object (he added wheels, doors, set name and color) and press save, I want to sent this filled(generated) JSON object to server and save it to DB. Is it possible? Thanks

    Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >