Search Results

Search found 10731 results on 430 pages for 'k day'.

Page 335/430 | < Previous Page | 331 332 333 334 335 336 337 338 339 340 341 342  | Next Page >

  • Why does the screen resolution of 1440x900 suddenly disappear from Intel GMA Control Panel?

    - by GeneQ
    I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2. I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've goggled this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • How to set minimum SQL Server resource allocation for a database?

    - by Jeff Widmer
    Over the past Christmas holiday week, when the website I work on was experiencing very low traffic, we saw several Request timed out exceptions (one on each day 12/26, 12/28, 12/29, and 12/30) on several pages that require user authentication. We rarely saw Request timed out exceptions prior to this very low traffic week. We believe the timeouts were due to the database that it uses being "spun down" on the SQL Server and taking longer to spin up when a request came in. There are 2 databases on the SQL Server (SQL Server 2005), one which is specifically for this application and the other for the public facing website and for authentication; so in the case where users were not logged into the application (which definitely could have been for several hours at a time over Christmas week) the application database probably received no requests. We think at this point SQL Server reallocated resources to the other database and then when a request came in, extra time was needed to spin up the application database and the timeout occurred. Is there a way to tell SQL Server to give a minimum amount of resources to a database at all times?

    Read the article

  • NTDS Replication Warning (Event ID 2089)

    - by Chris_K
    I have a simple little network with 3 AD servers in 2 sites. Site A has Win2k3 SP2 and Win2k SP4 servers, site B has a single Win2k3 SP2 server. All have been in place for at least 3 years now. Just last week I started getting Event 2089 "not backed up" warnings (example below) on both of the win2k3 servers. I understand what the message means, no need to send me links to the technet article explaining it. I'll improve my backups. What I'm more curious about is why did I just start getting this message now? Why haven't I been getting it for the past 3 years?!? Perhaps this is related: I recently decommissioned a few other sites and AD controllers (there used to be 3 more sites, each with their own controller). Don't worry, I did proper DCpromo exercises and made sure we didn't lose anything. But would shutting those down possibly be related to why I get this error now? This won't keep me awake at night but I am curious as to what changed... Event Type: Warning Event Source: NTDS Replication Event Category: Backup Event ID: 2089 Date: 3/28/2010 Time: 9:25:27 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: RedactedName Description: This directory partition has not been backed up since at least the following number of days. Directory partition: DC=MyDomain,DC=com 'Backup latency interval' (days): 30 It is recommended that you take a backup as often as possible to recover from accidental loss of data. However if you haven't taken a backup since at least the 'backup latency interval' number of days, this message will be logged every day until a backup is taken. You can take a backup of any replica that holds this partition. By default the 'Backup latency interval' is set to half the 'Tombstone Lifetime Interval'. If you want to change the default 'Backup latency interval', you could do so by adding the following registry key. 'Backup latency interval' (days) registry key: System\CurrentControlSet\Services\NTDS\Parameters\Backup Latency Threshold (days) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

    Read the article

  • mod_cache not working

    - by Pistos
    I have a PHP site that has many dynamically generated pages. I'm trying to turn to mod_cache to help boost performance, because in most cases, content does not change in a given day. I have configured mod_cache as best I could, following examples around the web, including the mod_cache page on apache.org. When I set LogLevel debug, I see a bit of information about the caching that is [not] happening. There are plenty of pairs of lines like this: [Fri Jun 01 17:28:18 2012] [debug] mod_cache.c(141): Adding CACHE_SAVE filter for /foo/bar [Fri Jun 01 17:28:18 2012] [debug] mod_cache.c(148): Adding CACHE_REMOVE_URL filter for /foo/bar Which is fine, because I've set CacheEnable disk /foo, to indicate that I want everything under /foo cached. I'm new to mod_cache, but my understanding about these lines is that it just means that mod_cache has acknowledged that the URL is supposed to be cached, but there are supposed to be more lines indicating that it is saving the data to cache, and then later retrieving them on subsequent hits to the same URL. I can hit the same URL till I'm blue in the face, whether with F5 refreshing, or not, or with different browsers, or different computers. It's always that pair of lines that shows in the logs, and nothing else. When I set CacheEnable disk /, then I see more activity. But I don't want to cache the entire site, and there are many, many different subpaths to the site, so I don't want to have to modify code to set no-cache headers in all the necessary places. I'll mention that mod_rewrite is in use here, rewriting /foo/bar to something like index.php?baz=/foo/bar, but my understanding is that mod_cache uses the pre-rewrite URL, not the post-rewrite URL. As far as I can tell, I have the response headers not getting in the way of caching. Here's an example from one hit: Cache-Control:must-revalidate, max-age=3600 Connection:Keep-Alive Content-Encoding:gzip Content-Length:16790 Content-Type:text/html Date:Fri, 01 Jun 2012 21:43:09 GMT Expires:Fri, 1 Jun 2012 18:43:09 -0400 Keep-Alive:timeout=15, max=100 Pragma: Server:Apache Vary:Accept-Encoding mod_cache config is as follows: CacheRoot /var/cache/apache2/ CacheDirLevels 3 CacheDirLength 2 CacheEnable disk /foo What is getting in the way of mod_cache doing its job of caching?

    Read the article

  • Hosting websites in our Workplace custom-built datacentre

    - by i.h4d35
    I'm faced with unique learning opportunity at work at the moment. Due to the slowdown (amongst other reasons), the powers that be at my office have decided to abandon our shared hosting providers (both shared and dedicated hosting) and have decided to host the websites at our office's datacentre. We're running 7 websites, wherein the average unique hits per day at the moment is about 900. We have 2 servers set aside for this - one is a DELL POWER EDGE 1850 (Intel Xeon 3 GHZ*2, 4GB RAM, 73GB HDD and the other is an HP DL 380 G3 (Intel Xeon 2.8 GHz, 6 GB RAM, 73 GB HDD) a) I would like to know the pros and cons of going ahead with this project.All the sites will be hosted on a single IP. In all probability, the OS is going to be CentOS. b) Do you think I should consider Virtualization into this equation (KVM/Xen)? I was thinking in terms of separate instances of the DB server and the frontend though I do not know if this is the best way to go. c) Should I be trying to use cloud stacks like OpenStack and try to make it look like websites hosted on some sort of Public Cloud? (something that I checked out here). Here is something else I came across, which looks similar to what needs to be done at our office. About the websites - Of the 7 websites, 4 are basic static websites which basically gives a whole lot of information about a few local institutions. The remaining 3 are local product-based websites developed in PHP wherein end user can view products and order them online. I am trying to take this as a learning experience wherein I can learn to build something from scratch and save the company a little something in the process. The migration needs to be completed by Easter so I guess it gives us some time (or am I being overly optimistic??). I am confused here and would appreciate all the help I can get. Thanks in advance.

    Read the article

  • Apache, httpd process 4MB+ memory use, Wordpress, Dedicated Server

    - by david
    What is happening to apache? I cannot trace down the processes doing this to my server. I can't anymore, the server is crashing every day a few times. Don't know what to do anymore, tried all the answers here, i can't find the problem. apache 5978 0.0 1.4 34060 14000 ? S 10:13 0:00 /usr/sbin/httpd apache 5979 1.8 3.6 61660 35632 ? S 10:13 0:02 /usr/sbin/httpd apache 5982 1.9 3.6 61712 35640 ? S 10:13 0:02 /usr/sbin/httpd apache 5983 0.0 1.7 46000 17480 ? S 10:13 0:00 /usr/sbin/httpd apache 5984 1.4 4.3 70880 42644 ? S 10:13 0:02 /usr/sbin/httpd apache 5985 2.6 4.3 69864 42888 ? S 10:13 0:04 /usr/sbin/httpd apache 5986 0.7 3.9 67240 39220 ? S 10:13 0:01 /usr/sbin/httpd apache 5987 0.8 3.9 67240 39228 ? S 10:13 0:01 /usr/sbin/httpd apache 5988 2.5 4.3 70136 43160 ? S 10:13 0:03 /usr/sbin/httpd apache 6151 0.0 1.7 45868 17404 ? S 10:15 0:00 /usr/sbin/httpd

    Read the article

  • Database mirroring login failure attempts on mirror server

    - by Chandan
    I have configured database mirroring between two servers at a distance 40 miles away from each other. Server specifications: SQL Server 2008,Standard Edition 64-bit This is same for principal,mirror and witness. The configuration is high-safety with automatic failover Initially we tested our .net application(web application) on both the principal and mirror and made sure that the login is not orpahned. Things run fine generally.But sometimes on the mirror server,I see login failed attempts: Login failed for user 'd0main\user'. Reason: Failed to open the explicitly specified database. [CLIENT: xx.xx.x.x] Message Error: 18456, Severity: 14, State: 38. This error appears 3-4 times a day but not more than that. My question to the experts is:If the principal is alive so why the application tries to connect to mirror.The default time-out for a .net webpage is 30 seconds,so is it possible that the application tries to connect principal and after 30 seconds even if principal is alive,it assumes that it is dead and thus tries to open a connection to mirror where it fails. Please help me with this problem.

    Read the article

  • IIS6 Virtual SMTP server isn't coming back up automatically after a system restart

    - by Julian James
    I've got a virtual server running Win2008 RC2. I've set up IIS6 with a virtual SMTP server on it to be the mail provider for the websites I'm hosting there. It all works great, but if for some reason the server reboots (auto updates are still enabled - I'm trying to make this as little work as possible as we've got a Lot of clients), the IIS6 doesn't restart the SMTP server. The failure causes 500 errors on the current setup, so I'm spending half the day apologising. Any ideas? In Services I've set everything to come back up automatically, but still no dice. As soon as I restart the SMTP, no problems, all the mail gets sent. It's working perfectly, it just won't restart on it's own. I'd really rather not turn auto updates off as we're such a small company I just can't spare the time to be manually updating 15 copies of windows every time MS decide there's a security patch. All advice appreciated! BTW, I am a complete newb to these forums. I searched but couldn't find an answer, so please be nice. But firm. I've got to learn here.

    Read the article

  • Troubleshooting loss of network connectivity in Windows 2003 - What else to check?

    - by Benny
    We are facing a weird problem in our data center. Our Backup server (running EMC Networker) loses network connection every alternate day around 3:00 AM (Backup schedule starts at midnight). After 2 hours of outage, the network connectivity recovers automatically and back to normal. What we observed: It is unlikely to be network issue, since it is directly connected to server farm switch (layer 2 connection without any intermediate hops). Further, the server is connected to two different switches for Load balancing using Broadcomm Teaming. a) If it were a switch related issue it is unlikely that both the network ports go down, since they are connected to different switch. b) A possibility Vlan wide issue is also ruled out since other devices in the same Vlan are fine. c) Switch interface status is always up. But there are lot of packet drops during the outage period - Can be attributed to high interface utilization of the backup server (near 100%) d) Connectivity is restored without any change on network. Next suspect is resource utilization on Windows server. Both CPU and Memory have rarely exceeded 80%, but NIC card utilization is alarmingly high (near 100%) Not really sure how to investigate this?

    Read the article

  • apache performance timing out

    - by Mike
    Im running a webserver where I'm hosting about 6-7 websites. Most of these websites get their content from MySQL which is hosted on the same server. Traffic average per day is about 500-600 unique visitors, about 150K hits per week. But for some reason sometimes websites send a timeout, OR sometimes websites dont load all images. I know that I should perhaps separate static content from dynamic content, but for now I think that's not a possibility. I would appreciate any suggestions on how could I improve the performance of apache, so it doesn't keep timing out. Server is running on Sempron LE 1300; 2.3GHz,512K Cache 2GB RAM 10Mbps/1Mbps Services: MySQL, ProFTPD, Apache. Private + Shared = RAM used Program ---------------------------------------------------- 1.2 MiB + 54.0 KiB = 1.2 MiB proftpd 4.1 MiB + 23.0 KiB = 4.1 MiB munin-node 20.8 MiB + 120.5 KiB = 20.9 MiB mysqld 47.3 MiB + 9.9 MiB = 57.3 MiB apache2 (22) top: Mem: 2075356k total, 1826196k used, 249160k free, Timeout 35 KeepAlive On MaxKeepAliveRequests 300 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 10 MinSpareServers 20 MaxSpareServers 20 MaxClients 60 MaxRequestsPerChild 1000 </IfModule> <IfModule mpm_worker_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule>

    Read the article

  • How could Load average numbers from 'htop' exceed 100% CPU utlization?

    - by Joe Huang
    I use 'htop' to monitor my web server. It's recently quite loaded and the Load average is showing something like this: Load average: 3.10 2.56 1.63 I searched the web about these numbers and I found an article about it: http://blog.scoutapp.com/articles/2009/07/31/understanding-load-averages In the article, it says if I have 2 CPUs, 2.0 means 100% CPU utilization. And my VPS has two CPUs, so what does 3.1 mean? How could it exceed 100% CPU utilization? And from these numbers, does it mean I should be wary about the loading now? But the performance seems totally fine, and this is a managed VPS, the hosting company has not notified me any warning about it. During day time, Load average always show these high numbers... here is another snapshot while writing. Load average: 3.03 2.77 1.97 Load average: 0.41 1.29 1.60 <---- 5 more minutes later So I am wondering how much room left for this site to grow in current configurations? What kind of proactive actions I should take in advance? I don't want to wait until the server bursts. Thanks.

    Read the article

  • Philips Monitor problems - vertical lines on screen

    - by asdasd
    I have an old CRT Philips Monitor 17'' and it was working well. There were problems with the electrical power and the monitor started to make some sound and a smoke was getting out of it. I quickly switched it off the power, and in the morning when the power was ok i started the monitor and it appeared to be working and it worked for a couple of minutes when i find out some smell was coming from it, and after 5 minutes the screen i was working shut down and on the monitor some vertical lines appeared - and nothing else. I thought it was the OS, so i rebooted the pc and while it was booting i realized the monitor didn't show the bios info etc, but the same vertical lines on the whole screen were on it, sometimes their color was changing and they were blinking, but no screen appeared - only those vertical lines. After a day, the monitor was ok again - i turned it on and no there were no lines, everything was working fine. The same for the next 2 days. My question is: If anyone had ever had the same problem, can you help me ? THe monitor may be ok now but i am afraid it can get back those lines again. I don't know what to do, if you know please tell me whether should i take it to the service or not. Thank you.

    Read the article

  • Excael 2007: Name range problems when linking workbooks

    - by Mike
    I've 30+ workbooks each with 5 specific worksheets (formated the same). Each worksheet's data needs to be linked to a master workbook, so that I end up with 5 master workbooks and all the specific data in one long table format $A$2:$I$750. (Are you still with me? ;)) I don't have access to a database, so I'm having to link the sheets to their master workbook directly. I've highlighted the data I need; named the range; and then tried referencing this from my master workbook. I get the #Value error symbol when I try to link (=[WorkbookName]!MyNamedRange) to a cell that doesn't match the top left cell of my range. Example: MyNamedrange is always =$A$2:$I43$ on one specific sheet. On my master workbook it works if it's referenced at A2 but I get #Value if it's referenced A1, or A44. Any ideas? I'm trying to link my data in one continous table so I can run a pivot on it, and other things. Can it be done like this, or should I just copy and paste? I'm trying to keep things 'linked'so I do not need to spend time C&Ping all day. Many thanks Mike.

    Read the article

  • Apache crashes every 5min

    - by Simon
    I'm relatively new to server issues, having a site of mine that I started early in the year grow beyond my capabilities of managing it. I need help. I recently moved out of my shared hosting environment onto a dedicated virtual server from Mediatemple. Each week, I run a script that fetches data from my DB, fetches data from last.fm's API and then tweets information to Twitter. My server uses Virtuozzo and when the script runs, Apache crashes every 5min. I checked and saw that the 'kmemsize' parameter reaches its cap (its 13mb). I realise my problem. The MySQL process stays open for long while Apache needs to handle lots of incoming links (about 200 000 pageviews for that day according to my previous host's AWSTATS). Yes, I'm quite unexperienced in this, and I'm clearly killing the server with too many incoming links while it has to manage the updating of the DB. So that is the precedent: I want a few answers. 1) Why did my shared hosting environment not crash apache every 5min? It ran fine, the site only slowed a lot. Clearly, it must be the virtual container and the kmemsize limit? 2) Where do I go from here? Would a physical server (not a virtual container) encounter the same problems? I sent a support request to Mediatemple as well. I need all the help I can get.

    Read the article

  • Why am I unable to reach local network computers, but able to browse the web?

    - by Igor Zinov'yev
    I have a weird problem. Today after turning my Ubuntu 9.10 PC on I can't connect to my local network, but I can use the Internet. We have a single Windows 2003 server machine that acts as a local main DNS server, DHCP server and a domain controller. Although it seems to give me the local IP address, I can not ping it, as well as any other machine on the net. I have tried all of the below and it didn't help: Rebooting; Reconnecting to the network; Forcing the dhclient to renew the IP address; Deleting and creating new connection profiles; Plugging my machine into another network outlet; Maybe it has something to do with routing, because I have tampered with routing tables the day before, but the tables seem ok to me: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 vboxnet0 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 Our LAN uses a D-Link DI-604 router, and it looks to me as if I am connected to the network outside the router. I can not even access its administration page. Please at least suggest what I can do to solve this. P.S. What seems strangest to me is that I can access the PC in question from outside the network by opening a port on the router. I have managed to ssh to it from outside, but I still can't ping nothing on the inside. P.P.S Today I tried reinstalling network-manager with --purge option, but it did no good. After that I created a new DCHP reservation for my PC in order to change my local IP, but that didn't change anything either. My PC is able to get a DHCP offer, but then it's unable to connect to any local computers. I am desperate.

    Read the article

  • Office 2007 constantly crashes, logged as Event ID 1000

    - by Nori
    I have a user, who despite my best efforts, is having constant Office 2007 crashes. I've tried deleting their profile and setting it up again, repairing office, uninstalling completely and then reinstalling, and swapping out memory sticks. One event log error I keep getting is the following: (note all the Office errors are event id 1000) Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: EMSMDB32.DLL, version: 12.0.6539.5000, time stamp: 0x4c1246f8 Exception code: 0xc0000005 Fault offset: 0x0005d8e2 Faulting process id: 0xf6c Faulting application start time: 0x01cb6633f33384f3 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\EMSMDB32.DLL Report Id: 0d4a2eab-d231-11df-80a0-4061868f5d10 I also get this: Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: olmapi32.dll, version: 12.0.6538.5000, time stamp: 0x4bfc6ad9 Exception code: 0xc0000005 Fault offset: 0x002357a9 Faulting process id: 0x5e4 Faulting application start time: 0x01cb661f4546aa77 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\olmapi32.dll Report Id: a4a90658-d224-11df-80a0-4061868f5d10 The Excel error is this: Faulting application name: EXCEL.EXE, version: 12.0.6535.5002, time stamp: 0x4bd2a7f1 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdbdf Exception code: 0xe06d7363 Fault offset: 0x0000b727 Faulting process id: 0x14a8 Faulting application start time: 0x01cb61ab7bc0abab Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\EXCEL.EXE Faulting module path: C:\Windows\syswow64\KERNELBASE.dll Report Id: ba0c454b-cd9e-11df-80a0-4061868f5d10 Also have gotten this for PowerPoint: Faulting application name: POWERPNT.EXE, version: 12.0.6500.5000, time stamp: 0x49a68f9d Faulting module name: COMShim.dll, version: 2010.3.325.110, time stamp: 0x4c51e0b1 Exception code: 0x40000015 Fault offset: 0x0001e388 Faulting process id: 0x1480 Faulting application start time: 0x01cb5fe9a0660e81 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\POWERPNT.EXE Faulting module path: C:\Program Files (x86)\FactSet\COMShim.dll Report Id: e03d2a21-cbdc-11df-9bc8-4061868f5d10 (Some of the above lines edited to keep you from scroll horizontally.) Lastly, I get this error several times a day, I don't think it is related but maybe it is: Failed extract of third-party root list from auto update cab at: http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab with error: A required certificate is not within its validity period when verifying against the current system clock or the timestamp in the signed file. Any ideas? This is driving me nuts.

    Read the article

  • Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

    - by Matt
    I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

    Read the article

  • Can Vista Windows Explorer be repaired/fixed?

    - by gurun8
    I'm running Windows Vista Home Premium on a Sony Vaio laptop. I think somehow my Windows Explorer has become corrupted. I don't recall any certain inciting incident like installing an unreputable 3rd party app or hardware failure but just recently my system won't wake after it's been left idle longer that 20 minutes and goes to sleep. I've also had problems launch certain apps, like Adobe InDesign CS3, that just basically freeze the system but leave mouse movements functioning for a short time before freezing the entire system which requires a hard reboot to resolve the freeze. The system seems to run normally when used but I fear there's a looming possibility that this is a house of cards and will all come crashing down soon. My question is this, can Windows Explorer be repaired/fixed? Before reformatting the system and starting over, which is most likely what I'm going to be forced to do, I'd like explore (no pun intended) my options in fixing the problem with a patch or reinstall or something of that nature. Reformatting my system will eat up a day or two of my time and I just don't have the time to spare right now.

    Read the article

  • DNS requests failing from computers that can ping DNS server

    - by dunxd
    I have a situation where computers in some of our remote offices from time to time lose the ability to use our DNS server (in head office) to resolve hostnames. The offices are connected via VPN using Cisco ASA 5505 (VPNclient config rather than Site to Site). Ping to the IP address of the DNS server works. But nslookup will get a "no response from server" message. Computers in other locations can use DNS fine. This is an intermittent problem. One day/hour it works, another it doesn't. Other offices connected in the same way work when another doesn't. No config changes have been made on routers around the time we see the problem. Some users have reported that the problem goes away after doing a repair connection in Windows XP. I think this could be caused by the DNS cache being flushed as part of this - the Windows DNS cache makes the intermittent problem look less so because it caches failed lookups as well as successful ones. However, it is possible some other aspect of Windows is involved. Windows 7 clients have also had the same problem. Any pointers on deeper troubleshooting, or anyone else found this?

    Read the article

  • What is the best VM for developing WPF apps from within OS X?

    - by MarqueIV
    All of my machines are Macs (Mac Pro, MacBook Pro, MacBook Air and Mac Mini (and Apple TV 2.0 too! :) ) but for my day-job, I develop .NET/WPF applications. Normally I just boot into Boot Camp and develop that way, which of course works great, but there are times when I need to simultaneously get to things on my Mac-side of the equation, so I've bought both VMware 3.1 and Parallels 6. Both work, however, even on my Mac Pro where I paid to upgrade to the better video cards (the NVidia 8600s I think vs. the stock ATI cards) the WPF performance bites!! Now this confuses me since both boast that they support not only hardware-accelerated OpenGL 2.1, but also hardware-accelerated DirectX 9 (VMware even allegedly supports DirectX 10!) via their respective virtual drivers and both can run 3D games just fine, even in a window. But even the simple act of resizing a WPF window that has a tiled background results in some HIDEOUS repainting and resizing behaviors. It's damn near closer to what you'd expect over RDP let alone a software-only renderer (forget accelerated hardware completely!) So... can anyone please tell me WTF WPF is doing differently? More importantly, how can I speed up the WPF performance? Should I switch to VirtualBox that also has support for DirectX? Or am I just gonna have to 'byte' the bullet (sorry... had to. So I like puns! Thank Jon Stewart!) and continue using Boot Camp?

    Read the article

  • Monitor reset itself and now I can't set the resolution/settings back to how it was before

    - by verve
    I've had my LG 24" widescreen monitor since 2009 and 2 weeks ago I noticed the monitor turned itself off (never had it done this before) so I switched it back on to find all the settings like gamma, resolution etc. different = looked like it had been reset. Everyone in the house swears they never unplugged and plugged it back in. When I opened a webpage the fonts and zoom on the pages were different and my desktop was strange too; fonts of the icons were different etc. The screen seems blurry and when I watch movies the faces look distorted so I thought I would try to first figure out the resolution it used to be but when I go under "Adjust screen resolution" none of the options work and there is no recommended resolution marked; all the options stretch out the screen and looks terrible so right now I have it set to the least distorted one. Then since the resolution wasn't working I set the other manual settings(done by physical buttons on the monitor) back to how it used to be (luckily, I had written these down). The monitor looks better but the resolution makes it a strain to use. I thought maybe some Windows update caused this crap so I tried to System Restore: didn't work. What went wrong? A few questions: 1) What was the likely cause of the monitor shutting down itself and screwing up the settings I have been using since the day I bought the monitor? 2) Why have the fonts changed everywhere unless this is a HDD/video card problem? 3) How do I find the perfect resolution it used to be? The monitor wants me to set it to 1920 x 1080 but that isn't one of the options although I don't remember what resolution I used before. I use the 16:9 setting while I try the available resolution options but nothing looks good! How do I find what it used to be? Manual available in PDF under Support: http://www.lg.com/ca_en/computer-products/monitors/LG-lcd-monitor-W2442PA-BF.jsp Win 7. IE 9.

    Read the article

  • rsnapshot schedule overlapping, help with backup schedule

    - by Znarkus
    Hello, I have to following configuration. rsnapshot.conf interval halfhourly 4 interval hourly 6 interval twohourly 12 interval daily 7 interval weekly 4 crontab 0,30 * * * * /usr/bin/rsnapshot halfhourly >> /var/log/rsnapshot.halfhourly.log 2>&1 5 * * * * /usr/bin/rsnapshot hourly >> /var/log/rsnapshot.hourly.log 2>&1 10 */2 * * * /usr/bin/rsnapshot twohourly >> /var/log/rsnapshot.twohourly.log 2>&1 15 3 * * * /usr/bin/rsnapshot daily >> /var/log/rsnapshot.daily.log 2>&1 20 6 * * MON /usr/bin/rsnapshot weekly >> /var/log/rsnapshot.weekly.log 2>&1 Only halfhourly is running correctly now. hourly spits out this error: rsnapshot encountered an error! The program was invoked with these options: /usr/bin/rsnapshot hourly ---------------------------------------------------------------------------- ERROR: Lockfile /var/run/rsnapshot.pid exists and so does its process, can not continue To me it seems like my 5 min space between halfhourly and hourly is too small. Is this configuration crazy? I like having backups every thirty minutes, that will probably save my ass some day. Please help me make a decent backup schedule, that doesn't clog up the system, but creates frequent enough backups. Thank you.

    Read the article

  • Windows Key is shutting my PC with Windows 7 down when pressed

    - by jasondavis
    I am having a really annoying problem lately with my Windows 7 PC. The problem, is all of a sudden, just within the last day or 2, anytime I hit the WIN (Windows keyboard key) instead of popping up the start menu, the system shuts down all my programs and trys to shut down, the only reason it doesn't suceed is because one of the programs I will have running will have an un-saved document, so it will ask me if I want to save the document before shutting down, I then can hit cancel and it halts the process. I do not remember installing anything and programs from from around the time it started doing this, maybe 2-3 days ago. I have gone through and searched Google for every Process running in the taskmanager to see which processes were REQUIRED for Windows to run, I then closed eveything down and killed all the non-essential Processes and the result was this... The reason you see notepad.exe is because I had it open with an unsaved document to keep the system from shutting down, I then tried hitting the win key after I shut each process down, after everything was shut to just show the above, it still tries to shut my system down, this is driving me insane, please help I am at a lost. I am about to see if I can try a different keyboard just encase it is some malfunction on the keyboard. The reason I need to access the WIN key or would like to is because I have Win + v set up to work with a special clipboard manager I believe it is called ClipX

    Read the article

  • How to diagnose website performance/app pool recycling with Windows 2008/IIS7

    - by ilasno
    Ok, so there are various symptoms here (clients and and our own employees complaining of intermittent slowdowns, getting 'kicked out' to login page or just having a save request not properly save the submitted data). The environment: Windows Server 2008 (Datacenter), Service Pack 2, 64-bit, 2x2.8 GHz processors, 7.5 GB RAM MS SQL Server 2008 (running on the same machine) IIS 7 There are ~10 websites running on the server, each in their own application pool - most of these pools are running in Integrated mode, 2 are in Classic, all are on .NET 2.0 and all run as ApplicationPoolIdentity. I'm trying to analyze, diagnose, and troubleshoot and am struggling with where to get more info about what could be happening. Here are some steps i have already taken: Set each application pool to recycle once per day, and removed any other automatic recycling Set a Virtual Memory Limit for each to 1024000KB (1GB) Enabled ALL 'Generate Recycle Event Log Entry' entries (Config Changes, Isapi Reported Unhealthy, Manual Recycle, Private Memory Limit Exceeded, Regular Time Interval, Request Limit Exceeded, Specific Time, Virtual Memory Limit Exceeded) I have seen the app pool processes recycle (in Task Manager) - a new one will start up, and then the first one dies off - and this has happened without the memory or time going over the settings. This is a fairly new server, and most of these came from Windows Server 2003/IIS6. Any 'next steps' for setting up information gathering, logging, diagnosing, etc. would be much appreciated! j

    Read the article

< Previous Page | 331 332 333 334 335 336 337 338 339 340 341 342  | Next Page >