Search Results

Search found 11897 results on 476 pages for 'dean rather'.

Page 337/476 | < Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >

  • I think my laptop just died

    - by Joel Coehoorn
    I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

    Read the article

  • Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

    - by Rister
    I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

    Read the article

  • How do I prevent a tar pipe from causing swapping?

    - by Jeff Shattock
    I have a rather large filesystem that I need to transfer from one Linux server to another. I figured the best way to do this was via a tar/netcat pipe arrangment, something like tar c . | pv | nc blah blah blah And it works great, the network stays fairly saturated, life is good. Until the source machine starts swapping. The files are on a raid on the source system, so the read speed is much faster than the write speed on the other end. Since the dest machine hasnt picked up the data yet, the source machine needs to stick it somewhere, so into RAM it goes, until there is no more free RAM. It then starts swapping, which is horribly painful since that machine has its OS installed on a somewhat slow CF card. Both machines have 4GB of physical ram, 64 bit Ubuntu 9.04 server. GigE link between them. How do I prevent this swapping? Can I put a "speed-limit" on the tar or netcat process so that the transfer speed doesn't overwhelm the write throughput on the destination end? The man pages didn't list anything, but there might be something I'm overlooking.

    Read the article

  • SBS DC DNS entries going missing?

    - by Chris W
    I've been looking at a problem on a friends SBS (2003) server where the client PC's aren't able to connect to the server with a variety of errors reported. Checking the server itself the only indicator of an issue is an error 5782: Dynamic registration or deregistration of one or more DNS records failed with the following error: No DNS servers configured for the local system. Running a dcdiag reports that there are no DNS records registered for the DC so I fixed the problem by doing a netdiag /fix after which the dcdiag comes back clean and clients are ok again. It happened a few weeks ago as well and the same fix solved it. What are the possible causes of the DC DNS entries going missing? Is this a config option that needs tweaking or could it be solved by something simple like scheduling the SBS server to re-boot periodically? The only change they can think of that was made near to the time of the first instance of this problem occurring is that RRAS was started up to allow for a VPN connection from a home user. NB - The server is setup with a pair of NICs in a team so the server has a single virtual NIC providing both LAN/WAN connections to it. An external hardware firewall is in use rather than the windows firewall.

    Read the article

  • Windows Not Honoring DHCP Scope

    - by jerhinesmith
    Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

    Read the article

  • SAFE MODE Restriction in effect. The script not allowed to access directory owned by uid

    - by user57221
    I am running a dedicated server with multiple websites. I have created a global directory for common scripts for all websites, rather than repeating them in every website directory. How can I make this global directory accessible for all website. I am getting following error. Warning: require_once() [function.require-once]: SAFE MODE Restriction in effect. The script whose uid is XXXX is not allowed to access /vhosts/globallibrary/Zend/Application.php owned by uid XXXX I have change the ownership of global directory for X website. so it works fine for X website. latter I added another website Y Now I am getting the same error again. If I change the CHOWN for Y website then X website will have the same error. I don't want to disable the safemode restriction. Is there a work around, so that this global dir will be accessible by all website. I am getting following error in my browser when I try to access global directory. Global directory is on same level as all other websites. Is this a good practice to enable safemode for websites?

    Read the article

  • How do I repartition an SDHC card in Windows?

    - by Peter Mortensen
    How do I repartition an SDHC card (4 GB or more)? Do I need third-part tools or Linux (a live CD solution would be OK)? In Windows' Disk Management the option Delete Partition is dimmed out: I can reformat the card as FAT32, copy files to and from the card and even change the file system to NTFS using the command line command CONVERT, but not repartition it. The article How to Partition an SD Card in Windows XP talks about using "a Windows enabler program" which sound rather dubious to me. I have tried to change from “Optimize for quick removal” to “Optimize for performance”. The option to format as NTFS appeared, but the Delete Partition option is still dimmed out. Platform: Windows XP 64-bit SD card reader: USB 2.0 device, LogiLink® CR0005C Cardreader 3,5' USB 2.0 intern 54-in-1 mit USB Front Kingston 16 GB SDHC card, speed class 4. (It could be formatted as FAT32 and successfully used in a 4 GB ReadyBoost setup (Windows 7).) I have also tried on different versions of Windows and with different cards with the same result: Kingston 4 GB SDHC card, speed class 4 (the one shown in the screenshot) Transcend 2 GB (not marked as SDHC, but SD) Windows 7 32-bit (albeit with a somewhat an older card reader) and Windows XP 32-bit on an EliteBook 8730w

    Read the article

  • How can I configure Samba to share (read/write) any folder with root permissions?

    - by Mike Toews
    I have a CentOS 5 VirtualBox guest on a Win7x64 host. I am attempting to setup a read/write share a directory owned by root with my Windows host using Samba, but I'm having no luck after running around in circles. To simplify matters, I've disabled my Firewall (/etc/init.d/iptables stop). As security and permissions are irrelevant for this purpose, I'd rather not have to set up another unix user/group/password. Here is the output from testparm Load smb config files from /etc/samba/smb.conf rlimit_max: rlimit_max (1024) below minimum Windows limit (16384) Processing section "[Guest Share]" Loaded services file OK. Server role: ROLE_STANDALONE and the source of /etc/samba/smb.conf: [global] workgroup = WRKGRP netbios name = SMBSERVER security = SHARE load printers = No [Guest Share] comment = Guest access share path = /root/src read only = No guest ok = Yes Running /etc/init.d/smb restart shows an OK status. However, on my Windows host, I can only see the share folder on the guest \\IPv4, but I cannot go into "Guest Share": "The network name cannot be found" error message is a common error, with a likely cause: The user you are trying to access the share with does not have sufficient permissions to access the path for the share. Both read (r) and access (x) should be possible. Am I trying to use root as a passwordless Samba guest? I'd like to, is it possible? How can I configure Samba to share (read/write) any folder with root permissions?

    Read the article

  • Upgrading memory in a laptop

    - by ulidtko
    I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

    Read the article

  • Why is the `remove rows` button not always present in MySQL Workbench?

    - by Shawn
    I'm using MySQL Workbench to remove rows from a table in my database. Most of the time, I will simply write a select statement, then select the rows I want to erase and use the remove rows button (circled in the screenshot below). But sometimes (quite often actually), the remove rows button does not appear. Instead, I get something like the screenshot below: The remove rows button is not there and the remove rows option is grayed out in the context menu, so basically, I can't remove rows... The only way I've found of solving this issue is to run the select query many times until the button appears (it usually does after 3 of 4 times). Does anyone know why this is happening? UPDATE Today, I've been running a select query dozens of times and the button never appears. It seems my incomprehensible workaround no longer works... Help! btw: Using a delete statement does work, though I would rather not have to write one for each row I want to remove as this happens quite frequently during development...

    Read the article

  • How do I cancel windows server 2003 repair install?

    - by Kilgore2k
    System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

    Read the article

  • OS X won't boot up unless I hold down option key

    - by Gazzer
    I have a strange issue on an early 2008 Mac Pro running OS 10.6: if I restart the computer it restarts normally if I shutdown and boot, it stops at the grey screen just before the boot process if I shutdown and boot but hold down the option key, I can select the boot disk and all is good. I've just cloned the disk, and the same thing happens. The disk is a SAMSUNG HD154UI The disk is partitioned (the second partition holds a clone of the Snow Leopard Install disk) One weird thing on the original disk was one of the partitions said 'EFI Boot' in a non-aliased font rather than the name of the disk when the disks are listed upon holding down option. Solution: it seems that there was a problem with the disk. Part of the difficulty in finding the solution was that you need to remove the disk from the computer completely. For example, a good disk in Bay 3, wouldn't boot up if the bad disk was in Bay 2. So for ages I thought the problem was hardware related in Bay 3. So if you think you have a dodgy disk remove it totally if you are testing the hardware with a 'clean' disk. Cleaning the PRAM helped to get the new disk to work too.

    Read the article

  • Booting an Asus EeePC from a LiveCD USB stick

    - by Bryan
    I have two identical Asus EeePC netbooks that are both installed with Ubuntu. One of them was sitting on the closet shelf and the battery went completely dead. When I charged the battery and tried to boot the it, I got the "No init found" error. In trying to follow the suggested way to fix it posted here, I used the Startup Disk Creator on my Ubuntu 11.10 desktop machine to create a USB stick with a bootable Ubuntu 11.10 live CD on it (the netbook doesn't have a CD drive). I plugged the USB stick into the netbook with the init issues, went into the BIOS and selected the USB stick as the 1st choice to boot from, and did a hard restart. It then just stuck at the flashing underscore. Not knowing why it wasn't working, I tried booting my working netbook from the USB stick. When I got into the BIOS on the working netbook, I noticed the description in the boot order section for the USB device was different. On the non-working netbook, the description was SWISSBIT (the name of the USB stick) but on the working netbook it was just "Rem. Drive". I also noticed on the working netbook there was an additional option under the bootable order section that allowed me to choose which hard drive to boot from. This section showed two hard drives, one of them being my USB stick. So, rather than changing the device boot order, I selected the USB stick as the hard drive to boot from first and it worked like a champ - I was able to boot into the LiveCD on the USB stick. Seems to me the working netbook is seeing the LiveCD USB stick as a hard drive, where-as the non-working netbook is seeing it as a plain ol' USB stick. The BIOS is the exact same version on both netbooks... any idea why it works on one and not on the other?

    Read the article

  • Why won't Media Monkey add one particular folder of mp3's?

    - by ChrisF
    I'm using the latest and greatest version on Media Monkey (free version) and it won't find the mp3's in one particular folder in my music tree. It can see all the other files in the tree and the folder shows up when I click Add/Rescan files to the library... I have full control over the folder and all the files in the folder. The files play in Windows Media Player. The files play in Media Monkey if I right click and play from the context menu. All the tracks are at least 2 minutes long and over 5MB long and Media Monkey is set to ignore files shorter than 20KB and include all files regardless of length. There was an issue in that the that the genre of the tracks was set to "Classical" and the option that allows you to browse the classical music independently of the other music isn't enabled in the free version. It's a Gold version option only. I hadn't spotted that my other classical music was also missing from the library (I have rather a large library). Once I retagged the music with a different tag and tried to add the files again it reported that it added the tracks, but they still didn't show up in the library.

    Read the article

  • Low-profile, PCI Express, x1 video card with VGA-out?

    - by Dandy
    I just bought an Acer Aspire EasyStore H340 system (http://us.acer.com/acer/productv.do?LanguageISOCtxParam=en&kcond61e.c2att101=54825&sp=page16e&ctx2.c2att1=25&link=ln438e&CountryISOCtxParam=US&ctx1g.c2att92=450&ctx1.att21k=1&CRC=936243954) It comes with Windows Home Server, which I don't particularly care for (too dumbed down for my liking)--I bought the box mainly for the form factor, and intend to install Server 2008 on it and have it run as a small domain controller. The geniuses at Acer however went out of their way to ensure you can only run Home Server--you can only connect to it via the Home Server Connector software, as it has no video-out whatsoever (so essentially, there's no way to even get into the BIOS). It only has a low-profile, PCI Express x1 slot. It turns out to be way harder than I thought to locate a video card that both has an x1 connector, and is low-profile (I'd really rather not snip the bracket at the back just so it'll fit the case). I know they're out there, and I've seen one with Display Port outputs, but I don't have a monitor with this connection. So to reiterate, it needs to be: - x1 connector - low profile - VGA out (though DVI would be okay; I have some spare adapters) Can anyone recommend anything at all?

    Read the article

  • Equivalent of scp -l bandwidth_cap for .ssh/config?

    - by Mark Bennett
    Short form: You can limit the bandwidth the scp uses with the -l switch, you pass a number that's in kbits/sec. I'd rather set this in my .ssh/config file for certain names machines. What's the equivalent named setting for -l ? I haven't been able to find it. Followup question: Generally, not sure how to map back and forth between ssh command line options and config names, short of doing Google searches or manually comparing man pages on a case by case basis. Is there a table that directly equates the two? Longer form of first question, with context: I've started using ssh config quite a bit, especially now that I need to go through a proxy and do lots of port mappings. I even define the same machine more than once depending on what type of tunneling I need. However, when uploading a large file, it's difficult to do anything else on my machine. Even though I have more download bandwidth than up, I think that scp saturates the link so even my small requests can't reach the Internet. There's a fix for this, using the -l bandwidth command line switch for scp. scp -l 1000 bigfile.zip titan: I'd like to use this in my config instead, so I'd create an additional named entry called "titan-upload" and I'd use that as the target whenever I upload. So instead of: scp bigfile.zip titan: I'd say: scp bigfile.zip titan-upload Or even set different caps depending on where I am: scp bigfile.zip titan-upload-from-home vs. scp bigfile.zip titan-upload-from-work I'm generally on Mac and Linux.

    Read the article

  • Wifi Works with Android and Windows 8 but not Linux and Win 7

    - by eramm
    Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

    Read the article

  • DVD-burner disappears when using grub

    - by drblah
    This is a rather annoying problem I have with Linux on my laptop. Whenever I install any Linux distro that relies on grub (which is about 99 % apparently) it will mess up my DVD-drive and the drive will not be recognized after booting, no matter the OS (Ubunntu, Arch, Windows Vista or 7). I know the problem has nothing to do the DVD-drive itself, because I bought a new one a few months ago. I am also sure that grub is messing the drive up, because I have tried to use LILO, which worked fine (except for horrible boot times.) This problem have persisted through about 3-4 years and it is a pretty bad show stopper whenever I want to work with Linux. I had hoped it would get fixed over time, but no one seems to have the exact problem I have. The drive is connected with an IDE connection. Update: The old drive was a Toshiba Samsung SN-S082. I don't know the model number of the new one, but it is HP (I think). Things I have tried to fix it: Mess about with some BIOS settings like enabling AHCI and change some IDE settings. Installing a different boot loader DOES fix the problem but I would like to use grub.

    Read the article

  • Web based KVM management for Ubuntu

    - by Tim
    We've got a single Ubuntu 9.10 root server on which we want to run multiple KVM virtual machines. To administer these virtual machines I'd like a web based KVM management tool, but I don't know which one to choose from the list of tools mentioned on linux-kvm.org. I've used virsh & virt-manager on my desktop, but would like a web interface for the server. I tested ConVirt on my desktop, but it failed to pickup KVM machines from virsh / virt-manager, and I could not get KVM virtual machine import to work (only Xen). oVirt looks good, but I can't find out if and how I can install it on Ubuntu 9.10.. (And I'd really rather not waste another few days on testing stuff that might not work in the end.) Can anyone recommend any good web based KVM management tools that are easy to install on Ubuntu 9.10? I'm looking for something that will also allow me to run other services like apache and postgresql besides hosting virtual machines, so preferably fairly lightweight & no dedicated OS installs. We don't need any professional clustering / migration or anything, just something that will let us create, start, inspect, administer & stop virtual machines from a web page. Best regards, Tim Update: Anyone have any suggestions? It's awfully quiet here..

    Read the article

  • Recommend a UK based VPS host equivalent to Dreamhost [closed]

    - by Pez Cuckow
    I appreciate this question could be considered subjective and argumentative so can people make recommendations rather than arguing about the best. I believe the "correct" answer is the one closest to what I am looking for. Basically I live in the UK but have been using the US based Dreamhost for about 6 years now, and my web projects are getting to the scale where the websites need to the UK based to cope with the demand and load. I originally had shared hosting with Dreamhost but upgraded to a VPS a while ago, getting 512mb of RAM, unlimited disk space, bandwidth and domains for $30. Their control panel is a custom easy to use build that they have created in house and offers features very similar to other web panels (as far as I am aware). So basically my question boils down to, is there anywhere that offers an equivalent package? In all honesty as long as I have over 50gb HDD space and unlimited domains it doesn't really matter? Are there any VPS providers you would recommend as reliable? I promise to check every link posted, many thanks for your time!

    Read the article

  • Assembly Level Language? Unlock iPhone 3GS with latest Baseband. Need Opinion

    - by getkenny
    Hi Guys, So its more like advice i need. I got 2 iPhone 3GS (Bootloader 06.02 and BB 05.11) which are lying around useless cause it was bought it from US and now i am in Dubai. Cannot use the phone because there is no unlock. Now rather than waiting and relying on other people to provide a unlock for the baseband , i was thinking of learning what it takes to unlock a iPhone. I currently don't even know what i got to learn to do this. I understand from soem reading around that i will need to learn ARM to understand the baseband and try to find a exploit: is it correct? I really want to help people out in getting their iPhones working. Also the iPhones cost was $645 each (16GB) so its not like Apple is going to loose any money of it, the person who bought it for me thought that if your not buying with an AT&T contract it means that it is unlocked but it is not true. I need help, i am willing to learn and you guys are the best bunch around to give me advice. Regards.

    Read the article

  • Is there a standard method for assigning nameservers to servers in a Windows domain?

    - by HopelessN00b
    As the title asks, I'm wondering if there's any standard or "best practice" for how to actually assign nameservers (DNS) and manage the nameserver configuration for client servers on a Windows domain. I'm talking about the setting circled in the below image, in case the language of the question is not clear enough: This is for a large, multi-site environment, where ideally/hopefully all servers point at their site's Domain Controller as the primary DNS server, and a DNS server at a different site as the secondary DNS server. For simplicity's sake, we can say that the secondary server would be the Domain Controller at the home site for everyone, and there are no tertiary DNS servers (even though that's not actually the case). Try as I might, I can't seem to find a GPO setting for this (at least on FL 2003 R2, the Computer Configuration - Administrative Templates - Network - DNS Client - DNS Servers GPO is Supported on: Windows XP Professional only), and I find it rather hard to believe that the "best"/"standard" solution would therefore be either scripting up something to apply the DNS settings per site, or using a DHCP server to push those configurations out to the other servers via the DHCP Scope Options. So, is there a standard way of managing this configuration? (That's hopefully not "a script" or "DHCP Scope Option.)

    Read the article

  • GPO - Setting not applied, although policy is applied

    - by Kenny Bones
    This is rather strange. In our domain we have several terminal servers and this morning a user reported that no drives are mapped when he logs on to the terminal server. So, I checked Group Policy Results and compare two users. Both users have the exact same policies applied. But for this particular user, the Script section under User Configuration - Policies - Windows Settings is just not there. For the other user, which this is working fine for, it says under the Script section that Winning GPO is Terminal2008, which is the GPO that contains the script section. And the Terminal2008 GPO is applied to both users. Also, the loopback processing is set to Replace. What could be the cause for this? I've never seen this particular issue before. I mean, both users are in the same OU, they log on to the same terminal server and the same policies are applied to both. They do not however have the exact same group memberships, but should that matter? It's not stated that the script should be run only if the user is a member of a certain group either. Not sure if that could be done through that specific setting either.All I know is, the very same policies are applied to both users, in the same OU and the same computer. Meaning, the same policies should be applied? Edit: I just ran Group Policy Results on one of the other terminal servers, which are also in the same OU, and the Scripts section is there! This means that this particular user don't get this setting when he's logged onto this particular server. What could be the cause of this?

    Read the article

  • Ubuntu 8.04 wont reboot from script

    - by Littlejon
    I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

    Read the article

  • Weird glitches on Intel iGPU

    - by FrederikVds
    I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

    Read the article

< Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >