Search Results

Search found 18096 results on 724 pages for 'let'.

Page 338/724 | < Previous Page | 334 335 336 337 338 339 340 341 342 343 344 345  | Next Page >

• Broadcom 4313 doesn't work following 12.04 upgrade

  - by Lucas

  I have an hp G62-228Ca laptop with a BCM4313 previously running Ubuntu 11.10. I ran the 12.04 upgrade last night without much thought. Following the upgrade and mandatory reboot, the wireless card no longer shows up in the network manager, the first time I've had any kind of issues with wireless under Ubuntu. I've done much Googling on the issue but so far I haven't found a permanent solution. Mucking around with some packages though (I've installed five different ones or so), I've managed to devise a workaround that I must run every time I boot the laptop. I have to remove the Broadcom STA driver and reinstall it. Inspiration taken from here: WiFi does not work, Broadcom STA Wireless driver does not work on a BCM4313 After the second modprobe command, the wireless reappears in the network manager and ten seconds after that I'm back on the wifi. If anyone can provide some advice on how to fix this permanently I will be extremely grateful. I'd rather not roll back to 11.10 or reinstall, but I will if I need to. Just let me know if you need the output from any terminal commands. Thanks in advance!

  Read the article

• nginx rewrite base url

  - by ptn777

  I would like the root url http://www.example.com to redirect to http://www.example.com/something/else This is because some weird WP plugin always sets a cookie on the base url, which doesn't let me cache it. I tried this directive: location / { rewrite ^ /something/else break; } But 1) there is no redirect and 2) pages start shooting more than 1,000 requests to my server. With this one: location / { rewrite ^ http://www.example.com/something/else break; } Chrome reports a redirect loop. What's the correct regexp to use?

  Read the article

• How do I uninstall the TuxOnIce kernel in 12.04?

  - by Lluis

  I recently installed tuxonice on a Toshiba z830. I have ubuntu 12.04 (kernel was: 3.2.0-26) I wanted to be able to hibernate, which I consider to be a basic thing a OS should allow you to do. Well, it didn't work...but they already tell you it may not so I removed it. For doing all these I followed: Problem with Hibernation After uninstalling I switched off the laptop and after this I started to have several problems. The first one was that Cisco VPN didn't work anymore and then I realised that I could not even suspend my laptop. I found very strange that after removing tuxonice I still had this: /lib/modules/3.2.0-26-generic-tuxonice/ The VPN problem could be solved by just copying from my previous kernel: 3.2.0-26-generic/CiscoVPN/ into the tuxonice one. Not very elegant but works. Now, for the suspend problem (and the previous too) I can hold Shift when starting and select my old kernel and then suspend works again. In my opinion tuxonice was not correctly uninstalled as it left that kernel behind and worse: ubuntu uses it if I do not take action. I have these work arounds....and here is my question: how can I delete this tuxonice kernel safely? If you need more info please let me know.

  Read the article

• How to force ADF to speak your language (or any common language)

  - by Blueberry Coder

  When I started working for Oracle, one of the first tasks I was given was to contribute some content to a great ADF course Frank and Chris are building. Among other things, they asked me to work on a module about Internationalization. While doing research work, I unearthed a little gem I had overlooked all those years. JDeveloper, as you may know, speaks your language - as long as your language is English, that is. Oracle ADF, on the other hand, is a citizen of the world. It is available in more than 25 different languages. But while this is a wonderful feature for end users, it is rather cumbersome for developers. Why is that? Have you ever tried to search the OTN forums for a solution with a non-English error message as your query? I have, once. But how can you force ADF to use English for its logging operations? Playing with your system settings will not help, unfortunately. By default, ADF will output its error messages in the selected locale for the operating system account the application server runs on. The only way to change this behavior is to pass initialization parameters to the JVM used by the application server. It is even possible to specify the language and country/region separately. In the example below, we choose English and the United States respectively. -Duser.language=en -Duser.country=US In the case of WebLogic Server, it is possible to add such parameters in setDomainEnv.sh (or .cmd) to apply the settings to all the managed servers present on a node. In the coming weeks, I will write a few posts about other internationalization issues. Is there anything you would like me to cover? Let me know in the comments.

  Read the article

• Marking Discussions as Answered

  As a contributor to a number of projects on CodePlex I really like the fact that the discussions feature exists but also I need ways to help me sort the discussions threads so I can make sure no-one is getting forgotten about. Seems like a lot of you agreed as the feature request Provide feature to allow Coordinators to mark Discussions threads as 'Answered' is our number 2 voted feature right now with 178 votes.  Today we rolled out the first iteration of “answer” support to discussions. In this first iteration we wanted to keep it simple and lightweight. The original poster of the thread along with project owners, developers or editors can mark any post to the thread as an answer. You can have any number of answers marked in a thread and it’s very quick to mark or unmark a post as an answer.  We deliberately keep the answers in the originally posted order so that you can see them in context with the discussion thread. When viewing discussions the default view is still to see everything, but you can easily filter by “Unanswered”.  You can even save that as a bookmark so as someone interested in the project can quickly jump to the unanswered discussion threads to go help out on. As I mention, we kept this first pass of the answering feature as simple and as lightweight as possible so that we can get some feedback on it. Head on over to the issue tracking this feature if you have any thoughts once you have used it for a bit or feel free to respond in the comments. I already have a couple of things I think we want to do such as a refresh of the look and feel of discussions in general along, make it easier to navigate to posts that are marked an answered and surface posts that you do that were marked as answered in your profile page - but if you have ideas then please let us know.

  Read the article

• Cannot boot: FGLRX 8.780 + Kernel 2.6.35-25

  - by pluc

  The situation before this all happened is pretty standard. I have a HP Pavillion dv5 laptop with an ATI Mobility Radeon 4200 series. It always worked fine with Ubuntu for as long as I can remember. However, at one point, something happened and truly made a majestic mess of things. It might've been extra repos I enabled with Ubuntu Tweak - I do not know. But something made it so that my system would not boot any longer. And when I say "won't boot", this is what I mean: - Durning a normal bootup, any entries (except Windows) selected with GRUB (or BURG, not even sure which one I'm using anymore) will spawn the Ubuntu loading screen - then try to start X (or GDM) 5 times. The screen goes to dark, black and back to the Ubuntu loading screen. Then it just stays there until I spawn another TTY. I have no idea what is happening or why. There are no errors in my logs, and I'm truly at a loss here. I've linked three files: Xorg.0.log, the output of dmesg and the GDM log: Xorg.0.log: http://ubuntu.pastebin.com/tpVKc2tc dmesg: ubuntu.pastebin.com/Nd5aYj45 gdm's :0.log: couldn't post due to lack of points :( Let me know if any of you more knowledgeable folks can restore some sanity in my life. Any help is greatly apreciated.

  Read the article

• What does SQL Server do if you select more than 1 full backup when doing a restore?

  - by Rob Sobers

  I have a backup file that contains 2 backup sets. Both backup sets are full backups. When I open SQL Server Management Studio and choose "Restore..." and pick the file as my device, it lets me pick both backup sets. The restore operation completes without error, but I'm not sure exactly what SQL server did. Did it restore the first one, drop the database, and then restore the second one? Will it always let the most recent full backup prevail? It doesn't seem to make sense for SQL server to even allow you to select more than one full backup.

  Read the article

• How do I restore the Gnome Panel volume control in Ubuntu 10.04?

  - by Neil

  I use alsa, and I don't have a volume control applet on my Gnome Panel. When I right click and select "add to panel", there is nothing that has to do with "sound", "audio" or "volume" in the list, and the "Indicator Applet" or "Indicator Applet Session" things have no volume controls, or properties that would let you enable any sort of volume control. How can I get a volume control in Ubuntu, so I don't have to run aumix in a terminal or something? I've been using Linux since Redhat 5, it's beyond me why these sorts of problems are still around. Someone should just put a damn "Volume Control" element in the list of things to add to the panel, even if it doesn't work, perhaps showing an error message.

  Read the article

• ADF Logging In Deployed Apps

  - by Duncan Mills

  Harking back to my series on using the ADF logger and the related  ADF Insider Video, I've had a couple of queries this week about using the logger from Enterprise Manager (EM). I've alluded in those previous materials to how EM can be used but it's evident that folks need a little help.  So in this article, I'll quickly look at how you can switch logging on from the EM console for an application and how you can view the output.  Before we start I'm assuming that you have EM up and running, in my case I have a small test install of Fusion Middleware Patchset 5 with an ADF application deployed to a managed server. Step 1 - Select your Application In the EM navigator select the app you're interested in: At this point you can actually bring up the context ( right mouse click) menu to jump to the logging, but let's do it another way.  Step 2 - Open the Application Deployment Menu At the top of the screen, underneath the application name, you'll find a drop down menu which will take you to the options to view log messages and configure logging, thus: Step 3 - Set your Logging Levels  Just like the log configuration within JDeveloper, we can set up transient or permanent (not recommended!) loggers here. In this case I've filtered the class list down to just oracle.demo, and set the log level to config. You can now go away and do stuff in the app to generate log entries. Step 4 - View the Output  Again from the Application Deployment menu we can jump to the log viewer screen and, as I have here, start to filter down the logging output to the stuff you're interested in.  In this case I've filtered by module name. You'll notice here that you can again look at related log messages. Importantly, you'll also see the name of the log file that holds this message, so it you'd rather analyse the log in more detail offline, through the ODL log analyser in JDeveloper, then you can see which log to download.

  Read the article

• Scp only a specific folder

  - by Ben

  Some command line syntax I don't know how to set, am a noob sometimes, sorry is that's obvious Let's says I have the following path for all my assets : /var/www/site/system/images/{image_id}/{format}/{file}.{extension} Inside the {image_id} folder, I have multiple formats (original, medium, thumb, etc...). I only want to import the /var/www/site/system/images/{image_id}/original folder, and keep the structure locally scp -r username@server:/var/www/site/system/images/*/original ~/Site/site/system/images This one does get it all, but all the files end up in the same and unique folder, no structure. I'd like to keep the structure. Is there something to do for it ?

  Read the article

• How to manage Agile developers working with traditional (serial) business persons?

  - by Riggy

  Good afternoon, My work environment has some problems. Our IT team is trying to be more agile, but we're not really getting buy-in from the business. They attend our daily stand-ups and sprint reviews, and they help with sprint planning, but then they turn around and do 4 months of requirements gathering for a project before moving forward with a (mostly) serial development style. The sprint goals are things like "get XX% closer to release". For the IT team, they've turned the Sprints into a sort of death march. We end a Sprint one day and start a new Sprint the very next day. There's no reflection or changes done between sprints, only during. Having never done any of the agile methodologies before, I haven't had a very pleasant introduction to them. So my questions are: 1) Should there be some time (perhaps a week or so) between sprints to do the reflection/introspection/changes/etc.? Or are back-to-back-to-back sprints the norm? 2) Is there any chance for survival for an agile team with no agile business counter-parts? If not, are there some transitional methodologies or even tips for moving the business towards an iterative if not necessarily agile mindset? 3) Should your entire team be on every sprint? We have almost 20 programmers on a single sprint but working on completely different projects (typically teams of 3-5, sometimes larger). Is it normal to have a single sprint or should we be trying to manage multiple independent sprints? Should we be trying to keep the multiple sprints in concurrent lockstep or should their timetables be allowed to overlap and be flexible? Any thoughts or advice is appreciated. This is my first time coming over from SO for a question, so please let me know if there are better ways to phrase these kinds of questions (faq was rather helpful, but still not sure I'm following it perfectly). Thanks!

  Read the article

• Can't get iptables firewall working correctly

  - by Jay

  I'm setting up a new Centos 5.6 system and can't get my iptables firewall to work correctly. it won't let me use SSH through it. I'm new to Centos but not to Linux or iptables. I've been removing things until I have isolated the problem. I set up the firewall with a default ACCEPT rule for the INPUT chain. I can connect through to the server fine. If I change the command to only allow traffic from the interface connecting to my trusted network it stops working. Working: iptables -A INPUT -s 0/0 -d 0/0 -j ACCEPT Failing: iptables -A INPUT -i eth0 -s 0/0 -d 0/0 -j ACCEPT I've double checked the ip address I'm using corresponds to eth0 using ifconfig. Any ideas where I went wrong?

  Read the article

• Lubuntu fails plug and play such as scanners; default file location on Gnumeric

  - by Arkay

  I am new to Lubuntu and I have been giving it a good try but confess I am now tempted to go back to Windows. However, I am open to persuasion if I can get a simple answer to two questions. The first is a hardware question issue. It seems from the forum that many users like me cannot use plug and play hardware such as scanners. Are we doing anything wrong or does Lubuntu (mine is 13.04) not support plug and play or scanners? I have read lots of previous answers about scanners but they all seem to involve re-writing lines of instructions to various areas of the system - not something an amateur like me can do with ease. Mine is a Packard Belle Diamond 1200 plus and apparently it should work fine on Lubuntu - but can I even get it recognised, let alone working - No? Secondly is there an easy way in Gnumeric to set the default file location so that I don't have to trawl through my whole tree to locate a file I want to open? Thanks to anybody who can get me stay with Lubuntu with their wisdom.

  Read the article

• Temporarily remove Group Policy in Windows 7

  - by rodey

  Using Windows 7 Professional I need to get access to the Folder Options screen. At work we primarily use Windows XP and are connected to a domain. Through Group Policy we disable access to the Folder Options. We use a tool called KillPol that temporarily removes Group Policy and let's me access the screen. This tool doesn't work on Windows 7 and I can't find a replacement. Any ideas on how I can get access to the Folder Options screen in Windows 7 when it is disabled through GP?

  Read the article

• Should we install the OS on an SSD or not when running virtual machines?

  - by Raghu Dodda

  I have a new Dell Mobile Precision M6500 laptop with 8 GB RAM. it has two hard drives - 500 GB @7200 RPM and a 128 GB SSD. The main purpose of these laptop is software development in virtual machines. The plan is to install the base OS (Windows 7) and all the programs in the 500 GB drive, and let the SSD only contain the virtual machine images. It is my understanding that the we get most performance from the virtual machines if the images are on a separate hard drive than the base OS. Is this the way to go, or should I install the OS on the SSD as well? What are the pros and cons? The virtual machine images would be between 20 - 30 GB, and I might run 1 or 2 at a time.

  Read the article

• I'm trying to setup Xvfb to run an GUI app on a remote server with no display

  - by jz87

  I have a 3rd party java app that I need to run on a remote server. Unfortunately, the app is designed for the desktop and assumes a GUI is available. The thing is I would like to leave this app running on the remote server without having to tie up my desktop machine with a persistent VNC connection to the remote machine. I'm trying to setup Xvfb on the remote machine so emulate a graphical environment, connect to the remote machine via VNC to launch the app and configure parameters and then log off and let it run. Here's what I have so far: I have ubuntu 11.04 server apt-get install xvfb apt-get install fluxbox apt-get install x11vnc Xvfb :1 -screen 0 1024x768x16 & fluxbox & At this point I run into a problem because it gives a very undescriptive error: Cannot connect to server. How do I know if the server is running and that it's running properly?

  Read the article

• Windows XP not starting up anymore (BSOD)

  - by Richard

  When I tried to start my computer running Windows XP yesterday, as I turned on the screen it was stuck at the "Welcome" screen. I had to reset it. After that, I got stuck at the point where the BIOS should load the OS - I turn on the PC, the Motherboard and BIOS post message shows up, then the blinking "thing" in the top left corner shows up 2 seconds, then everything is black. After I let it run for some time in that mode, it automatically restarts. I'm writing this here from a Ubuntu 9.10 Live CD. What can I do to fix this? How can I find out what is wrong? I'm a programmer and okay with doing (very) advanced things in that terms, so if you know something just tell me and I'll try

  Read the article

• Implementing unit testing at a company that doesn't do it

  - by Pete

  My company's head of software development just "resigned" (i.e. fired) and we are now looking into improving the development practices at our company. We want to implement unit testing in all software created from here on out. Feedback from the developers is this: We know testing is valuable But, you are always changing the specs so it'd be a waste of time And, your deadlines are so tight we don't have enough time to test anyway Feedback from the CEO is this: I would like our company to have automated testing, but I don't know how to make it happen We don't have time to write large specification documents How do developers get the specs now? Word of mouth or PowerPoint slide. Obviously, that's a big problem. My suggestion is this: Let's also give the developers a set of test data and unit tests That's the spec. It's up to management to be clear and quantitative about what it wants. The developers can put it whatever other functionality they feel is needed and it need not be covered by tests Well, if you've ever been in a company that was in this situation, how did you solve the problem? Does this approach seem reasonable?

  Read the article

• Drupal migration failed

  - by Marco

  First of all, I'm new to Drupal and the work I have to do is some kind of too hard. My old colleague (webmaster) had a server with a multisite Drupal 6 installation. Sites and their dirs were (e.g.) Sites Site directory b.a.mycompany.com /drupal_install_dir/sites/b.a.mycompany.com c.a.mycompany.com /drupal_install_dir/sites/c.a.mycompany.com d.a.mycompany.com /drupal_install_dir/sites/d.a.mycompany.com Unluckily my colleague moved and server hdd aren't in my hands: all I have is a backup of /drupal_install_dir and three sql dumps (one for each site). I had to restore three sites, but changing them as z.mycompany.com/b z.mycompany.com/c z.mycompany.com/d Beeing a sysadmin, I Extracted tar.gz backup file under wwwroot (let's call full path to extracted directory /new_install_dir) Restored three databases Created mysql users and give them correct GRANTS on databases Then (trying to restore at least first site) I changed /new_install_dir/sites/settings.php putting correct database connection data and new basepath. But there is no way I can see my new site, simply it doesn't work. Watching /var/log/apache2/error.log I saw Drupal searching for main drupal database; so I created that db too setting user and grants, but dump file is empty. Well, now I can run something like install.php or update.php, but my site is not shown. Is there something I can do? Do I have to walk another way? Consider I searched the web, but I'm not able to find a guide that can help me for my problem. Ah, I forgot: before producing the backup, my colleague set site in maintenance mode. When I try to run z.mycompany.com/?q=user (trying to login) nothing happens. I'm really stuck...

  Read the article

• Trouble installing gnome-shell-extensions-user-theme, dependency/PPA conflict?

  - by Drex

  I installed gnome tweak tool, and am trying to set up custom themes and whatnot. So, trying to install gnome-shell-extensions-user-theme. me@computer:~$ sudo apt-get install gnome-shell-extensions-user-theme [sudo] password for me: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: gnome-shell-extensions-user-theme : Depends: gnome-shell-extensions-common but it is not going to be installed E: Unable to correct problems, you have held broken packages. Not going to be installed? Okay, let's see about that... me@computer:~$ sudo apt-get install gnome-shell-extensions-common Reading package lists... Done Building dependency tree Reading state information... Done gnome-shell-extensions-common is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Wait, what? Broken packages? Ruh Roh! Seems to me it might be a PPA contradiction problem or something, but I'm tired of trashing my installs. Kinda lost here. Any ideas? Output of sudo apt-get install -f drex@U110:~$ sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.

  Read the article

• LibGDX onTouch() method kill on touch

  - by johnny-b

  How can I add this on my application. i want to use the onTouch() method from the implementation of the InputProcessor to kill the enemies on screen. how do i do that? do i have to do anything to the enemy class? please help Thank you M @Override public boolean touchDown(int screenX, int screenY, int pointer, int button) { return false; } here is my enemy class public class Bullet extends Sprite { private Vector2 velocity; private float lifetime; public Bullet(float x, float y) { velocity = new Vector2(0, 0); } public void update(float delta) { float targetX = GameWorld.getBall().getX(); float targetY = GameWorld.getBall().getY(); float dx = targetX - getX(); float dy = targetY - getY(); float distToTarget = (float) Math.sqrt(dx * dx + dy * dy); velocity.x += dx * delta; velocity.y += dy * delta; } } i am rendering all graphics in a GameRender class and a gameworld class if you need more info please let me know Thank you

  Read the article

• set chars to uppercase between parenthesis

  - by emzap79

  let's assume in vim I have following lines: all what (strong) people have to do is pushing (heavy) weights over (and over) again in order to gain muscles and I need to convert words inside parenthesis to uppercase, what is the most convenient way to do so? How do I tell vim it needs to select everything to the first (!) closing parenthesis? So far I came up with :%s/\s(.*)\s/\U&/g unfortunately this will uppercase everything between 'strong' and 'heavy' which is not what I want. Any chance to tell vim it should select the chars to the next closing bracket only? (sorry for the silly example, couldn't think of something more sophisticated... or at least vim related... huh)

  Read the article

• rsync synchronizing files only without creating folders on destination

  - by Vincent

  Is it possible with rsync to not create directories on destination? Imagine I have that source : a/ a/x.txt b/ b/y.txt And that I have this destination : a/ a/z.txt The wanted result of rsync source destination : a/ a/x.txt a/z.txt Of course my real situation involves thousand files/folders structure and I don't want solutions involving explicit list of synced folders, which I can do. I'm looking for a clean way just to prevent any folder creation on destination. By exclude or filtering... That could even be something outside rsync, like a hack with permissions if rsync can't do this... For information, this is really easy to get this kind of situations, in my case I have: A server with 2 disks, let's say A & B. And a local drive C. I usually use rsync to sync (and merge) remote A & B into local C. Then sometimes I just want to sync back some C files into A and B. (Just new Files... not non-existing folders on destination)

  Read the article

• facebook keeps freezing Chrome and Windows

  - by missingfaktor

  Hi, everyone. I am a Windows 7 and Chrome user. Lately (since past few months) my Chrome has been freezing, taking down whole operating system with it, leaving resetting the computer the only choice. Recently I discovered that the issue was with facebook tabs, and when I close those tabs (if it's not too late!), I can save Chrome and Windows from a complete crash. This is very annoying. Is there a solution for this problem? Maybe uninstalling/reinstalling some plugins? Please help. Thanks. PS: Let me know if for helping me with this issue you need to know the list of extensions I have installed. I'll provide it in as an addendum.

  Read the article

• How to avoid the GameManager god object?

  - by lorancou

  I just read an answer to a question about structuring game code. It made me wonder about the ubiquitous GameManager class, and how it often becomes an issue in a production environment. Let me describe this. First, there's prototyping. Nobody cares about writing great code, we just try to get something running to see if the gameplay adds up. Then there's a greenlight, and in an effort to clean things up, somebody writes a GameManager. Probably to hold a bunch of GameStates, maybe to store a few GameObjects, nothing big, really. A cute, little, manager. In the peaceful realm of pre-production, the game is shaping up nicely. Coders have proper nights of sleep and plenty of ideas to architecture the thing with Great Design Patterns. Then production starts and soon, of course, there is crunch time. Balanced diet is long gone, the bug tracker is cracking with issues, people are stressed and the game has to be released yesterday. At that point, usually, the GameManager is a real big mess (to stay polite). The reason for that is simple. After all, when writing a game, well... all the source code is actually here to manage the game. It's easy to just add this little extra feature or bugfix in the GameManager, where everything else is already stored anyway. When time becomes an issue, no way to write a separate class, or to split this giant manager into sub-managers. Of course this is a classical anti-pattern: the god object. It's a bad thing, a pain to merge, a pain to maintain, a pain to understand, a pain to transform. What would you suggest to prevent this from happening?

  Read the article

< Previous Page | 334 335 336 337 338 339 340 341 342 343 344 345  | Next Page >