Search Results

Search found 4287 results on 172 pages for 'frame'.

Page 34/172 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• wxPthon problems with Wrapping StaticText

  - by Scott B

  Hello. I am having an issue with wxPython. A simplified version of the code is posted below (white space, comments, etc removed to reduce size - but the general format to my program is kept roughly the same). When I run the script, the static text correctly wraps as it should, but the other items in the panel do not move down (they act as if the statictext is only one line and thus not everything is visible). If I manually resize the window/frame, even just a tiny amount, everything gets corrected and displays as it is should. I took screen shots to show this behavior, but I just created this account and thus don't have the required 10 reputation points to be allowed to post pictures. Why does it not display correctly to begin with? I've tried all sorts of combination's of GetParent().Refresh() or Update() and GetTopLevelParent().Update() or Refresh(). I've tried everything I can think of but cannot get it to display correctly without manually resizing the frame/window. Once re-sized, it works exactly as I want it to. Information: Windows XP Python 2.5.2 wxPython 2.8.11.0 (msw-unicode) Any suggestions? Thanks! Code: #! /usr/bin/python import wx class StaticWrapText(wx.PyControl): def __init__(self, parent, id=wx.ID_ANY, label='', pos=wx.DefaultPosition, size=wx.DefaultSize, style=wx.NO_BORDER, validator=wx.DefaultValidator, name='StaticWrapText'): wx.PyControl.__init__(self, parent, id, pos, size, style, validator, name) self.statictext = wx.StaticText(self, wx.ID_ANY, label, style=style) self.wraplabel = label #self.wrap() def wrap(self): self.Freeze() self.statictext.SetLabel(self.wraplabel) self.statictext.Wrap(self.GetSize().width) self.Thaw() def DoGetBestSize(self): self.wrap() #print self.statictext.GetSize() self.SetSize(self.statictext.GetSize()) return self.GetSize() class TestPanel(wx.Panel): def __init__(self, *args, **kwargs): # Init the base class wx.Panel.__init__(self, *args, **kwargs) self.createControls() def createControls(self): # --- Panel2 ------------------------------------------------------------- self.Panel2 = wx.Panel(self, -1) msg1 = 'Below is a List of Files to be Processed' staticBox = wx.StaticBox(self.Panel2, label=msg1) Panel2_box1_v1 = wx.StaticBoxSizer(staticBox, wx.VERTICAL) Panel2_box2_h1 = wx.BoxSizer(wx.HORIZONTAL) Panel2_box3_v1 = wx.BoxSizer(wx.VERTICAL) self.wxL_Inputs = wx.ListBox(self.Panel2, wx.ID_ANY, style=wx.LB_EXTENDED) sz = dict(size=(120,-1)) wxB_AddFile = wx.Button(self.Panel2, label='Add File', **sz) wxB_DeleteFile = wx.Button(self.Panel2, label='Delete Selected', **sz) wxB_ClearFiles = wx.Button(self.Panel2, label='Clear All', **sz) Panel2_box3_v1.Add(wxB_AddFile, 0, wx.TOP, 0) Panel2_box3_v1.Add(wxB_DeleteFile, 0, wx.TOP, 0) Panel2_box3_v1.Add(wxB_ClearFiles, 0, wx.TOP, 0) Panel2_box2_h1.Add(self.wxL_Inputs, 1, wx.ALL|wx.EXPAND, 2) Panel2_box2_h1.Add(Panel2_box3_v1, 0, wx.ALL|wx.EXPAND, 2) msg = 'This is a long line of text used to test the autowrapping ' msg += 'static text message. ' msg += 'This is a long line of text used to test the autowrapping ' msg += 'static text message. ' msg += 'This is a long line of text used to test the autowrapping ' msg += 'static text message. ' msg += 'This is a long line of text used to test the autowrapping ' msg += 'static text message. ' staticMsg = StaticWrapText(self.Panel2, label=msg) Panel2_box1_v1.Add(staticMsg, 0, wx.ALL|wx.EXPAND, 2) Panel2_box1_v1.Add(Panel2_box2_h1, 1, wx.ALL|wx.EXPAND, 0) self.Panel2.SetSizer(Panel2_box1_v1) # --- Combine Everything ------------------------------------------------- final_vbox = wx.BoxSizer(wx.VERTICAL) final_vbox.Add(self.Panel2, 1, wx.ALL|wx.EXPAND, 2) self.SetSizerAndFit(final_vbox) class TestFrame(wx.Frame): def __init__(self, *args, **kwargs): # Init the base class wx.Frame.__init__(self, *args, **kwargs) panel = TestPanel(self) self.SetClientSize(wx.Size(500,500)) self.Center() class wxFileCleanupApp(wx.App): def __init__(self, *args, **kwargs): # Init the base class wx.App.__init__(self, *args, **kwargs) def OnInit(self): # Create the frame, center it, and show it frame = TestFrame(None, title='Test Frame') frame.Show() return True if __name__ == '__main__': app = wxFileCleanupApp() app.MainLoop() EDIT: See my post below for a solution that works!

  Read the article

• Adjust parameters of serial port reading

  - by clinisbut

  Hello. I'm facing a particular issue that regards serial communication under win32. I'm communicating with a device can only accept frames when it is not already communicating. So I must find a valid frame and then inmediatelly send my request. I developed a class named Serial that handles basic operations on serial port (open, close, read, write) and then a Thread calls inside a loop read and write functions. Thread loop //Device is an object of class Serial while( device->isOpen() && !terminate ) { unsigned int readed = 0; unsigned long error = ERROR_SUCCESS; unsigned char* data = device->read( &readed, &error ); if( error==ERROR_SUCCESS ) { //If data received, deliver to upper level if( readed>0 ) { QByteArray output( (const char*)data, (signed int)readed ); emit dataArrived( output, readed ); } } else { //unrelated stuff } //Here I manage the writting issue //Only when nothing is received, and Upper layer wants to send a frame //(Upper layer only will mark as something to send when it detects a valid frame) if( readed==0 ) { out_lock.lock(); //If something to send... if( something_to_send > 0 ) { if( device->write( output_buffer, output_size, &error ) ) { //things... } } } } The Thread basically keeps reading, and when nothing is received, sees if somebody has signaled to send a frame (this means that a valid frame is just received). When this happens, it writes the frame through serial port. Here comes my problem. Inside the Serial::read() function: I use the overlapped way of reading: ::ClearCommError( handle, &dwErrors, &stat); if( stat.cbInQue ) { //If there's something to read, read it, please note the bytes to read parameter, here 1. bool ok = ::ReadFile( handle, buffer_in, 1, &bytes_read, &ov_reader ); if( !ok ) { DWORD _error = ::GetLastError(); if( _error == ERROR_IO_PENDING ) { DWORD result = ::WaitForMultipleObjects( 2, waiters, FALSE,INFINITE ); switch( result ) { //Eventshutdown case WAIT_OBJECT_0: /*code omitted*/break; case WAIT_OBJECT_0+1: ok = ::GetOverlappedResult( handle, &ov_reader, &bytes_read, true ); //check ok value omitted break; } } } } if( bytes_read>0 ) { *size = bytes_read; } Here starts my problem. When device sends me small frames (around 30 bytes) everything works fine, but when larger frames are sent, the code is not able to find any free time between frames causing the thread to never be able send any frame because readed is never 0. If I increase the number of bytes to read inside the read() function, lose the ability to detect when the device "listens": bool ok = ::ReadFile(handle, buffer_in, 50, &bytes_read, &ov_reader ); This happens because my app can receive the end of a frame together with the start of the next one. This behaviour is very common. In the other hand, if I change the INFINITE argument by a valid timeout in the WaitForMultipleObjects function, I lose data. So my question basically is... what I'm doing wrong? Why when reading 1 byte each time I don't find any free time to send my own frames? Thank you

  Read the article

• IE 11 Developer Tools - changing console target to a different frameset or iframe

  - by vladimirl

  Originally posted on: http://geekswithblogs.net/vladimirl/archive/2013/10/25/ie-11-developer-tools---changing-console-target-to-a.aspxTo change current console iframe/frameset type this into console command line where "contentIFrame" in the iframe/frameset name (there should not be quotes around the iframe name):console.cd(contentIFrame);To return to the top level window, use cd() with no argument:console.cd();It took me some time to find out that this was possible in IE 11 Developer tools. Everything is so much easier in Chrome. No drama. Sometimes I feel that I hate IE more and more. Reference (http://msdn.microsoft.com/en-us/library/ie/dn255006(v=vs.85).aspx#console_in):All script entered in the command line executes in the global scope of the currently selected window. If your webpage is built with a frameset or iframes, those frames load their own documents in their own windows.To target the window of a frameset frame or an iframe, use the cd() command, with the frame/iframe's name or ID attribute as the argument. For example, you have a frame with the name microsoftFrame and you're loading the Microsoft homepage in it.JavaScriptcd(microsoftFrame); Current window: www.microsoft.com/en-us/default.aspx Important  Note that there were no quotes around the name of the frame. Only pass the unquoted name or ID value as the parameter.To return to the top level window, use cd() with no argument.

  Read the article

• Wire Framing WP7 Apps With Cacoo

  - by Tim Murphy

  While looking for a free alternative to Sketchflow I landed on the Cacoo web site.  Any developer who decides to use the free Visual Studio tools may find themselves doing the same search.  The base functionality of Cacoo is free although there are certain features that have fees attached to them such as extended stencils and templates. Cacoo doesn’t seem to have a template for WP7.  It does have templates for iOS and Android development so I started with the Android template and started modidfying it for WP7.  Funny thing is since Android has the same hardware vendors as Windows Phone the basic frame looks just right (I would swear I was looking at my Samsung Focus). Below is the start of a new mockup for the user group that I help run. I found that while Cacoo doesn’t have all the icons I need I am able to insert them from the Windows Phone Toolkit folder.  If I put them off to the side as you can see above.  I can simply copy and paste them into the appropriate place as needed.  Beyond that I have customized the main frame frame so I can have my base to work from.  In the future I intend to create this as a stencil and if it looks good enough I would consider making it public. My use of this product is still in it’s early phase, but it seems like a great way to start.  Maybe if you use this to get going you can earn enough from your resulting apps to pay for something with more bells and whistles in the future. del.icio.us Tags: WP7,Windows Phone 7 development,design,Cacoo,wire frame

  Read the article

• Adding objects to the environment at timed intervals

  - by david

  I am using an ArrayList to handle objects and at each interval of 120 frames, I am adding a new object of the same type at a random location along the z-axis of 60. The problem is, it doesn't add just 1. It depends on how many are in the list. If I kill the Fox before the time interval when one is supposed to spawn comes, then no Fox will be spawned. If I don't kill any foxes, it grows exponentially. I only want one Fox to be added every 120 frames. This problem never happened before when I created new ones and added them to the environment. Any insights? Here is my code: /**** FOX CLASS ****/ import env3d.EnvObject; import java.util.ArrayList; public class Fox extends Creature { private int frame = 0; public Fox(double x, double y, double z) { super(x, y, z); // Must use the mutator as the fields have private access // in the parent class setTexture("models/fox/fox.png"); setModel("models/fox/fox.obj"); setScale(1.4); } public void move(ArrayList<Creature> creatures, ArrayList<Creature> dead_creatures, ArrayList<Creature> new_creatures) { frame++; setX(getX()-0.2); setRotateY(270); if (frame > 120) { Fox f = new Fox(60, 1, (int)(Math.random()*28)+1); new_creatures.add(f); frame = 0; } for (Creature c : creatures) { if (this.distance(c) < this.getScale()+c.getScale() && c instanceof Tux) { dead_creatures.add(c); } } for (Creature c : creatures) { if (c.getX() < 1 && c instanceof Fox) { dead_creatures.add(c); } } } } import env3d.Env; import java.util.ArrayList; import org.lwjgl.input.Keyboard; /** * A predator and prey simulation. Fox is the predator and Tux is the prey. */ public class Game { private Env env; private boolean finished; private ArrayList<Creature> creatures; private KingTux king; private Snowball ball; private int tuxcounter; private int kills; /** * Constructor for the Game class. It sets up the foxes and tuxes. */ public Game() { // we use a separate ArrayList to keep track of each animal. // our room is 50 x 50. creatures = new ArrayList<Creature>(); for (int i = 0; i < 10; i++) { creatures.add(new Tux((int)(Math.random()*10)+1, 1, (int)(Math.random()*28)+1)); } for (int i = 0; i < 1; i++) { creatures.add(new Fox(60, 1, (int)(Math.random()*28)+1)); } king = new KingTux(25, 1, 35); ball = new Snowball(-400, -400, -400); } /** * Play the game */ public void play() { finished = false; // Create the new environment. Must be done in the same // method as the game loop env = new Env(); // Make the room 50 x 50. env.setRoom(new Room()); // Add all the animals into to the environment for display for (Creature c : creatures) { env.addObject(c); } for (Creature c : creatures) { if (c instanceof Tux) { tuxcounter++; } } env.addObject(king); env.addObject(ball); // Sets up the camera env.setCameraXYZ(30, 50, 55); env.setCameraPitch(-63); // Turn off the default controls env.setDefaultControl(false); // A list to keep track of dead tuxes. ArrayList<Creature> dead_creatures = new ArrayList<Creature>(); ArrayList<Creature> new_creatures = new ArrayList<Creature>(); // The main game loop while (!finished) { if (env.getKey() == 1 || tuxcounter == 0) { finished = true; } env.setDisplayStr("Tuxes: " + tuxcounter, 15, 0); env.setDisplayStr("Kills: " + kills, 140, 0); processInput(); ball.move(); king.check(); // Move each fox and tux. for (Creature c : creatures) { c.move(creatures, dead_creatures, new_creatures); } for (Creature c : creatures) { if (c.distance(ball) < c.getScale()+ball.getScale() && c instanceof Fox) { dead_creatures.add(c); ball.setX(-400); ball.setY(-400); ball.setZ(-400); kills++; } } // Clean up of the dead tuxes. for (Creature c : dead_creatures) { if (c instanceof Tux) { tuxcounter--; } env.removeObject(c); creatures.remove(c); } for (Creature c : new_creatures) { creatures.add(c); env.addObject(c); } // we clear the ArrayList for the next loop. We could create a new one // every loop but that would be very inefficient. dead_creatures.clear(); new_creatures.clear(); // Update display env.advanceOneFrame(); } // Just a little clean up env.exit(); } private void processInput() { int keyDown = env.getKeyDown(); int key = env.getKey(); if (keyDown == 203) { king.setX(king.getX()-1); } else if (keyDown == 205) { king.setX(king.getX()+1); } if (ball.getX() <= -400 && key == Keyboard.KEY_S) { ball.setX(king.getX()); ball.setY(king.getY()); ball.setZ(king.getZ()); } } /** * Main method to launch the program. */ public static void main(String args[]) { (new Game()).play(); } } /**** CREATURE CLASS ****/ /* (Parent class to Tux, Fox, and KingTux) */ import env3d.EnvObject; import java.util.ArrayList; abstract public class Creature extends EnvObject { private int frame; private double rand; /** * Constructor for objects of class Creature */ public Creature(double x, double y, double z) { setX(x); setY(y); setZ(z); setScale(1); rand = Math.random(); } private void randomGenerator() { rand = Math.random(); } public void move(ArrayList<Creature> creatures, ArrayList<Creature> dead_creatures, ArrayList<Creature> new_creatures) { frame++; if (frame > 12) { randomGenerator(); frame = 0; } // if (rand < 0.25) { // setX(getX()+0.3); // setRotateY(90); // } else if (rand < 0.5) { // setX(getX()-0.3); // setRotateY(270); // } else if (rand < 0.75) { // setZ(getZ()+0.3); // setRotateY(0); // } else if (rand < 1) { // setZ(getZ()-0.3); // setRotateY(180); // } if (rand < 0.5) { setRotateY(getRotateY()-7); } else if (rand < 1) { setRotateY(getRotateY()+7); } setX(getX()+Math.sin(Math.toRadians(getRotateY()))*0.5); setZ(getZ()+Math.cos(Math.toRadians(getRotateY()))*0.5); if (getX() < getScale()) setX(getScale()); if (getX() > 50-getScale()) setX(50 - getScale()); if (getZ() < getScale()) setZ(getScale()); if (getZ() > 50-getScale()) setZ(50 - getScale()); // The move method now handles collision detection if (this instanceof Fox) { for (Creature c : creatures) { if (c.distance(this) < c.getScale()+this.getScale() && c instanceof Tux) { dead_creatures.add(c); } } } } } The rest of the classes are a bit trivial to this specific problem.

  Read the article

• Tkinter on Ubuntu 14.04 seems not to work

  - by empedokles

  I receive following Traceback: Traceback (most recent call last): File "tkinter_basic_frame.py", line 4, in <module> from Tkinter import Tk, Frame, BOTH File "/usr/lib/python2.7/lib-tk/Tkinter.py", line 42, in raise ImportError, str(msg) + ', please install the python-tk package' ImportError: No module named _tkinter, please install the python-tk package This is the demoscript I'm trying to run: #!/usr/bin/python # -*- coding: utf-8 -*- from Tkinter import Tk, Frame, BOTH class Example(Frame): def __init__(self, parent): Frame.__init__(self, parent, background="white") self.parent = parent self.initUI() def initUI(self): self.parent.title("Simple") self.pack(fill=BOTH, expand=1) def main(): root = Tk() root.geometry("250x150+300+300") app = Example(root) root.mainloop() if __name__ == '__main__': main() From my knowledge Tkinter should be included in Python 2.7. Why do I receive the traceback? Doesn't ubuntu contain the standard-python-distribution? This is solved. I had to install it manually in synaptic (got the hint in the meantime from another forum), see here: Wikipedia says: "Tkinter is a Python binding to the Tk GUI toolkit. It is the standard Python interface to the Tk GUI toolkit1 and is Python's de facto standard GUI,2 and is included with the standard Windows and Mac OS X install of Python." - Not good, that it isn't included in Ubuntu as well. Tkinter on Wikipedia

  Read the article

• IOS OpenGl transparency performance issue

  - by user346443

  I have built a game in Unity that uses OpenGL ES 1.1 for IOS. I have a nice constant frame rate of 30 until i place a semi transparent texture over the top on my entire scene. I expect the drop in frames is due to the blending overhead with sorting the frame buffer. On 4s and 3gs the frames stay at 30 but on the iPhone 4 the frame rate drops to 15-20. Probably due to the extra pixels in the retina compared to the 3gs and smaller cpu/gpu compared to the 4s. I would like to know if there is anything i can do to try and increase the frame rate when a transparent texture is rendered on top of the entire scene. Please not the the transparent texture overlay is a core part of the game and i can't disable anything else in the scene to speed things up. If its guaranteed to make a difference I guess I can switch to OpenGl ES 2.0 and write the shaders but i would prefer not to as i need to target older devices. I should add that the depth buffer is disabled and I'm blending using SrcAlpha One. Any advice would be highly appreciated. Cheers

  Read the article

• Internet is not working in base machine

  - by surendar

  I have a Ubuntu desktop. I am running a virtual windows machine using virtual box. Few days before Internet is not working in Ubuntu but it is working in the virtual machine. Even the samba shares are also accessible. I don't know why internet is not working in the base machine. I have tried to ping google.com, but it returns Ubuntu@desktop:~$ ping google.com ping: unknown host google.com ifconfig command's output Ubuntu@desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:27:0e:1b:86:2a inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::227:eff:fe1b:862a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38221 errors:0 dropped:0 overruns:0 frame:0 TX packets:28161 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39144616 (39.1 MB) TX bytes:6143919 (6.1 MB) Interrupt:27 Base address:0x2000 eth0:0 Link encap:Ethernet HWaddr 00:27:0e:1b:86:2a inet addr:192.168.2.7 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:27 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14944 errors:0 dropped:0 overruns:0 frame:0 TX packets:14944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1735451 (1.7 MB) TX bytes:1735451 (1.7 MB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:c0:00:01 inet addr:192.168.243.1 Bcast:192.168.243.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:77 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet HWaddr 00:50:56:c0:00:08 inet addr:172.16.162.1 Bcast:172.16.162.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:78 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• How to improve batching performance

  - by user4241

  Hello, I am developing a sprite based 2D game for mobile platform(s) and I'm using OpenGL (well, actually Irrlicht) to render graphics. First I implemented sprite rendering in a simple way: every game object is rendered as a quad with its own GPU draw call, meaning that if I had 200 game objects, I made 200 draw calls per frame. Of course this was a bad choice and my game was completely CPU bound because there is a little CPU overhead assosiacted in every GPU draw call. GPU stayed idle most of the time. Now, I thought I could improve performance by collecting objects into large batches and rendering these batches with only a few draw calls. I implemented batching (so that every game object sharing the same texture is rendered in same batch) and thought that my problems are gone... only to find out that my frame rate was even lower than before. Why? Well, I have 200 (or more) game objects, and they are updated 60 times per second. Every frame I have to recalculate new position (translation and rotation) for vertices in CPU (GPU on mobile platforms does not support instancing so I can't do it there), and doing this calculation 48000 per second (200*60*4 since every sprite has 4 vertices) simply seems to be too slow. What I could do to improve performance? All game objects are moving/rotating (almost) every frame so I really have to recalculate vertex positions. Only optimization that I could think of is a look-up table for rotations so that I wouldn't have to calculate them. Would point sprites help? Any nasty hacks? Anything else? Thanks.

  Read the article

• Bash script using eyeD3 to remove extra tags from mp3 files

  - by jaguare22

  I found what looks like the perfect script for this but getting errors. Hoping someone can see problem. I am running 12.04 Server. Error is - awk: line 0: regular expression compile failed (missing '(') ): awk: line 0: regular expression compile failed (missing '(') ) The following tags have been found in the mp3s: These tags are to be stripped: Here is a the script obtained from savvyadmin !/bin/bash Script name: strip-tags.sh Original Author: Ian of DarkStarShout Blog Site: http://darkstarshout.blogspot.com/ Options slightly modified to liking of SavvyAdmin.com oktags="TALB APIC TCON TPE1 TPE2 TPE3 TIT2 TRCK TYER TCOM TPOS" indexfile=mktemp Determine tags present: find . -iname "*.mp3" -exec eyeD3 --no-color -v {} \; $indexfile tagspresent=sort -u $indexfile | awk -F\): '/^<.*$/ {print $1}' \ | uniq | awk -F\)\> '{print $1}' | awk -F\( '{print $(NF)}' \ | awk 'BEGIN {ORS=" "} {print $0}' rm $indexfile Determine tags to strip: tostrip=echo -n $tagspresent $oktags $oktags \ | awk 'BEGIN {RS=" "; ORS="\n"} {print $0}' | sort | uniq -u \ | awk 'BEGIN {ORS=" "} {print $0}' Confirm action: echo echo The following tags have been found in the mp3s: echo $tagspresent echo These tags are to be stripped: echo $tostrip echo echo -n Press enter to confirm, or Ctrl+C to cancel... read dummy Strip 'em stripstring=echo $tostrip \ | awk 'BEGIN {FS="\n"; RS=" "} {print "--set-text-frame=" $1 ": "}' First pass copies any v1.x tags to v2.3 and strips unwanted tag data. Second pass removes v1.x tags, since I don't like to use them. Without --no-tagging-time-frame, a new unwanted tag is added. :-) find . -iname "*.mp3" \ -exec eyeD3 --to-v2.3 --no-tagging-time-frame $stripstring {} \; \ -exec eyeD3 --remove-v1 --no-tagging-time-frame {} \; echo "Script complete!"

  Read the article

• Game actions that take multiple frames to complete

  - by CantTetris

  I've never really done much game programming before, pretty straightforward question. Imagine I'm building a Tetris game, with the main loop looking something like this. for every frame handle input if it's time to make the current block move down a row if we can move the block move the block else remove all complete rows move rows down so there are no gaps if we can spawn a new block spawn a new current block else game over Everything in the game so far happens instantly - things are spawned instantly, rows are removed instantly etc. But what if I don't want things to happen instantly (i.e animate things)? for every frame handle input if it's time to make the current block move down a row if we can move the block move the block else ?? animate complete rows disappearing (somehow, wait over multiple frames until the animation is done) ?? animate rows moving downwards (and again, wait over multiple frames) if we can spawn a new block spawn a new current block else game over In my Pong clone this wasn't an issue, as every frame I was just moving the ball and checking for collisions. How can I wrap my head around this issue? Surely most games involves some action that takes more than a frame, and other things halt until the action is done.

  Read the article

• Stuck at enemy movement

  - by Syed

  I am making a TD game in unity, Initially I made all of my enemy movements frame rate dependent say: I had a grid point1 at -22.65 and other at -21.1, diagrammatically: (-22.65) _________(-21.1)_______(-21.1+1.55) ...... so the distance on x axis between two points is 1.55, divided it by 25 jumps with each enemy jump of 0.062 of each frame. On reaching on next point of grid the enemy find again its path. All went fine until I have requirement of FastForward and Pause feature. I used timeScale property of unity but it wont work as they are frame dependent. I also tried double speed of enemy on clicking fast forward button at any time, it has some issues that enemy jumps are now less and it fails to reach on next grid point. Could someone suggest me solution to my problem. Do I need to change the enemy movement code to make it frame independent ?? I need the enemy to reach on the grid specific point I also need later to slow down any one enemy's speed when tower fires on it. Thnx

  Read the article

• How do I install the EW-7318Ug wireless drivers?

  - by user69731

  I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

  Read the article

• Fixed timestep with interpolation in AS3

  - by Jim Sreven

  I'm trying to implement Glenn Fiedler's popular fixed timestep system as documented here: http://gafferongames.com/game-physics/fix-your-timestep/ In Flash. I'm fairly sure that I've got it set up correctly, along with state interpolation. The result is that if my character is supposed to move at 6 pixels per frame, 35 frames per second = 210 pixels a second, it does exactly that, even if the framerate climbs or falls. The problem is it looks awful. The movement is very stuttery and just doesn't look good. I find that the amount of time in between ENTER_FRAME events, which I'm adding on to my accumulator, averages out to 28.5ms (1000/35) just as it should, but individual frame times vary wildly, sometimes an ENTER_FRAME event will come 16ms after the last, sometimes 42ms. This means that at each graphical redraw the character graphic moves by a different amount, because a different amount of time has passed since the last draw. In theory it should look smooth, but it doesn't at all. In contrast, if I just use the ultra simple system of moving the character 6px every frame, it looks completely smooth, even with these large variances in frame times. How can this be possible? I'm using getTimer() to measure these time differences, are they even reliable?

  Read the article

• Adding root bone in 3DS Max?

  - by carlturtle

  my animation artist has made me a nice first person pair of arms, animated it, textured it, and given it to me. Then he went on vacation. I am programming my animations, and I am trying to test the model he has given me. Building my project gives me a warning: Multiple skeletons were found in the file. The first skeleton, named "frame l upperarm" has been moved to be a child of the scene root. The other, "frame r upperarm", will be ignored. Fragment identifier "frame r upperarm". Then an error: "Vertex is bound to bone "frame l forearm", but this bone is not present in the skeleton." I realize this means that there are two skeletons, as said in this problem: Importing 3d model with multiple skeletons I have 3DS Max, but I have no idea how to use it, and Google/CGTalk/Plycount turn up nothing relevant on how to add a root bone or combine skeletons. If anyone knows how, it would help me out greatly. Thanks.

  Read the article

• Drawing visible tiles - side scrolling

  - by Troubleshoot

  Currently I'm calling drawMap every time repaint is called. This is the code I've written for my drawMap method so far. public void drawMap(Graphics2D g2d) { float cameraX = Player.getX() - (Frame.CANVAS_WIDTH / 2); float cameraY = Player.getY() - (Frame.CANVAS_HEIGHT / 2); int tileX = (int) cameraX; int tileY = (int) cameraY; int xIndent = 0, yIndent = 0; int a = 0, b = 0; while (tileX % TILE_SIZE != 0) { tileX--; xIndent++; } while (tileY % TILE_SIZE != 0) { tileY--; yIndent++; } for (int y = tileY; y < tileY + Frame.CANVAS_HEIGHT; y += Map.TILE_SIZE) { for (int x = tileX; x < tileX + Frame.CANVAS_WIDTH; x += Map.TILE_SIZE) { if ((y / TILE_SIZE < 0 || x / TILE_SIZE < 0) || (y / TILE_SIZE > columnSize)) break; g2d.drawImage(map[y / TILE_SIZE][x / TILE_SIZE], a - xIndent, b - yIndent, null); a += TILE_SIZE; } a = 0; b += TILE_SIZE; } } The idea behind this is that it gets the camera position and draws the map relative to the player position. However, instead of the player being in the center of the screen all the time, the player actually moves away from the center as it scrolls to the right, and moves towards to center as it scrolls to the left. I've been trying to pinpoint what I've done wrong but I can't seem to find it. My code also seems quite messy, so am I doing this the correct way?

  Read the article

• Kubuntu not showing eth0

  - by Laurbert515

  I just installed Kubuntu 12.04.2 and do not have an internet connection. I also cannot access the Desktop and only have the terminal. When I enter xlcock I get Error: Can't open display:. I believe this is because I do not have the correct drivers and need to download them ... using the internet which I can't access. So here's what's going on ... ifconfig gives: lo Link ecap: Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:0 RX bytes:1296 (1.2 KB) TX bytes:1296 (1.2 KB) wlan0 Link encap: Ethernet HWaddr 68:17:29:58:49:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lspci -nnk gives: 07:00.0 Network Controller [0280] Intel Corporation Centrino Wireless-N 2230 [8086:0887] (rev c4) Subsystem: Intel Coporation Centrino Wireless-N 2230 BGN [8086:4062] Kernel driver in use: iwlwifi Kernel modules: iwlwifi 0d:00.0 Ethernet Controller [0200]: Atheros Communications Inc. AR8161 Gigabit Ethernet [1969:1091] (rev 10) Subsystem: Toshiba America Info Systems Device [1179:fa77] I believe this means that it is using the ethernet connection but thinks it is a wireless connection. sudo lshw -class network gives: *-network description: Wireless interface product: Centrino Wireless=N 2230 ... *network UNCLAIMED description: Ethernet controller product: AR8161 Gigabit Ethernet I want to get the internet working so I can fix the GPU driver, etc. but I can't seem to get it working even though I have my ethernet cable plugged in (and I'm sure it is working).

  Read the article

• How to revert to Eclipse's old behavior when double-clicking on frames or windows, in Juno?

  - by mattquiros

  I find Eclipse Juno very counter-intuitive. In my workspace, I used to just have the package view at the left, my code on the right, and whenever I'm printing something in the console, that's only when the console frame shows up from the bottom right. When you double click on a particular window, it either only goes fullscreen within Eclipse, or back to its original size together with the size of the other frames. In Juno, however, it seems that frames are put on layers on top of each other. When I print something to the console, the output frame only shows up as a small, useless square to my right. When I double-click, it goes full screen. When I double-click again, it occupies the full right frame, hiding my code. I double-click again and it goes full screen, then it double-clicks before it shares the right frame with my code on top of it. Then when I minimize it, it goes to the side. Any way to go back to the good old days of Eclipse? Thanks.

  Read the article

• Wireless is connected, but can't browse the Internet (or connection goes completely)

  - by user261007

  I'd like some help with this, please. Will be very glad is anyone will point me in the right direction. Thank you in advance! This is when the connection is present and browsing: eth0 Link encap:Ethernet HWaddr 50:46:5d:4a:9e:4f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2666 errors:0 dropped:0 overruns:0 frame:0 TX packets:2666 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:228844 (228.8 KB) TX bytes:228844 (228.8 KB) wlan0 Link encap:Ethernet HWaddr dc:85:de:1c:91:f9 inet addr:192.168.1.147 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::de85:deff:fe1c:91f9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18780 errors:0 dropped:0 overruns:0 frame:0 TX packets:12817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21198762 (21.1 MB) TX bytes:1746891 (1.7 MB) When connection goes: wlan0 Link encap:Ethernet HWaddr dc:85:de:1c:91:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:209503 errors:0 dropped:0 overruns:0 frame:0 TX packets:132560 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:268811733 (268.8 MB) TX bytes:15479814 (15.4 MB)

  Read the article

• How to change the value of a JLabel in runtime?

  - by user365465

  I want to change the image a JLabel is viewing during runtime, but I keep getting NullPointerExceptions or nothing happens when I press the magic button that's supposed to do things. Is it even possible in Java? Here is my code in its entirety: import java.text.*; import javax.swing.text.*; import java.util.*; import java.awt.*; import java.awt.event.*; import javax.swing.*; import javax.swing.event.*; public class Shell implements ActionListener, MenuKeyListener { JFrame frame; JWindow window; JButton PSubmit; JPanel pane1, pane2; JRadioButton R1, R2, R3; ButtonGroup PGroup; JTabbedPane layout; String result; String border = "Border.png"; String DF = "Frame.png"; String list []; Driver driver; public Shell() { driver = new Driver(); list = new String [6]; } public void setFrame() { frame = new JFrame("Pokemon Program 3 by Systems Ready"); frame.setSize(600, 600); frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); frame.setVisible(true); frame.getContentPane().setLayout(new BorderLayout()); } public void frameLayout() { layout = new JTabbedPane(); JPanel pane1 = new JPanel(); JPanel pane2 = new JPanel(); JLabel label = new JLabel("Please choose the restrictions:"); JLabel imgLabel1 = new JLabel(new ImageIcon(border)); JLabel notiLabel1 = new JLabel("The Pokemon chosen with these restrictions are: "); JLabel notiLabel2 = new JLabel("'No Restrictions': No restrictions for the kind of Pokemon chosen based on species or items."); JLabel notiLabel3 = new JLabel("'Battle Revolution': All Pokemon must have unique items."); JLabel notiLabel4 = new JLabel("'Battle Tower': All Pokemon must have unique items, Uber and Event Legendaries banned."); JLabel label2 = new JLabel("Please choose possible Pokemon:"); pane1.add(label); pearlButtons(); pane1.add(R1); pane1.add(R2); pane1.add(R3); pane1.add(PSubmit); pane1.add(notiLabel2); pane1.add(notiLabel3); pane1.add(notiLabel4); pane1.add(imgLabel1); pane1.add(notiLabel1); JLabel pokeLabel1 = new JLabel(new ImageIcon(DF)); JLabel pokeLabel2 = new JLabel(new ImageIcon(DF)); JLabel pokeLabel3 = new JLabel(new ImageIcon(DF)); JLabel pokeLabel4 = new JLabel(new ImageIcon(DF)); JLabel pokeLabel5 = new JLabel(new ImageIcon(DF)); JLabel pokeLabel6 = new JLabel(new ImageIcon(DF)); pane1.add(pokeLabel1); pane1.add(pokeLabel2); pane1.add(pokeLabel3); pane1.add(pokeLabel4); pane1.add(pokeLabel5); pane1.add(pokeLabel6); pane2.add(label2); layout.add("Pearl Version", pane1); layout.add("SoulSilver Version", pane2); frame.add(layout); } public void pearlButtons() { PGroup = new ButtonGroup(); R1 = new JRadioButton("No Restrictions", true); R1.setActionCommand("N"); R1.setVisible(true); R2 = new JRadioButton("Battle Revolution"); R2.setActionCommand("BR"); R2.setVisible(true); R3 = new JRadioButton("Battle Tower"); R3.setActionCommand("B"); R3.setVisible(true); PGroup.add(R1); PGroup.add(R2); PGroup.add(R3); PSubmit = new JButton("Submit"); PSubmit.setActionCommand("pstart"); PSubmit.setVisible(true); PSubmit.addActionListener(this); } public void pearlProcessing() { //The "list" array has a bunch of string names that get .png affixed to them (and I named the image files as such when I name them) String file1 = list[0] + ".png"; String file2 = list[1] + ".png"; String file3 = list[2] + ".png"; String file4 = list[3] + ".png"; String file5 = list[4] + ".png"; String file6 = list[5] + ".png"; /*-------------------------------------------------------------------------------// This is where the method's supposed to go to change the image... I've tried pokeLabel = new JLabel(new ImageIcon(file1));, but that yields a NullPointerException. //-----------------------------------------------------------------------------------*/ } public static void main(String[] args) { Shell test = new Shell(); test.setFrame(); test.frameLayout(); test.frame.setVisible(true); } public void actionPerformed(ActionEvent e) { if ("pstart".equals(e.getActionCommand())) { result = PGroup.getSelection().getActionCommand(); if (result.equals("N")) { list = driver.Prandom(); pearlProcessing(); } else System.out.println("Not done yet! ;)"); } } public void menuKeyPressed(MenuKeyEvent e) { System.out.println("pressed"); } public void menuKeyReleased(MenuKeyEvent e) { System.out.println("menuKeyReleased"); } public void menuKeyTyped(MenuKeyEvent e) { System.out.println("menuKeyTyped"); } }

  Read the article

• Network Access: I can't access 192.168.1.101 from 192.168.1.102.

  - by takpar

  Hi, I'm running Ubuntu 10.04 on my PC with IP 192.168.1.101. every thing work fine, e.g. my web server is running and I can see http://localhost/ or http://192.168.1.101 properly. But the problem is that I cannot see my PC from my laptop at 192.168.1.102 e.g. at my laptop http://192.168.1.101 gives Connection timed out in browser. or trying to telnet on any port leads to: telnet: Unable to connect to remote host: Connection timed out laptop is running a fresh install of Ubuntu as well and there is no setup for firewall stuff in both computers. PS: Both computers can ping each other well. The router is a cicso linksys wireless ADSL modem. Currently, I can connect to FTP server on the Windows running on 192.168.1.102 from 192.168.1.101 without problem. Theses are commands ran on my PC, 192.168.1.101: ifconfig: adp@adp-desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:e1:8e:cf inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::226:18ff:fee1:8ecf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1831935 errors:0 dropped:0 overruns:0 frame:0 TX packets:1493786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1996855925 (1.9 GB) TX bytes:215288238 (215.2 MB) Interrupt:27 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:951742 errors:0 dropped:0 overruns:0 frame:0 TX packets:951742 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:494351095 (494.3 MB) TX bytes:494351095 (494.3 MB) vmnet1 Link encap:Ethernet HWaddr 00:50:46:c0:00:01 inet addr:192.168.91.1 Bcast:192.168.91.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet HWaddr 00:50:46:c0:00:08 inet addr:192.168.156.1 Bcast:192.168.156.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) port 80 is set to 0.0.0.0 well: adp@adp-desktop:~$ netstat -ln | grep 'LISTEN ' tcp 0 0 127.0.0.1:52815 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4559 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4369 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:7634 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5269 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:25 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5280 0.0.0.0:* LISTEN tcp 0 0 127.0.1.1:7777 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:33601 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5222 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp6 0 0 :::139 :::* LISTEN tcp6 0 0 ::1:631 :::* LISTEN tcp6 0 0 :::445 :::* LISTEN /etc/hosts.deny is empty: adp@adp-desktop:~$ cat /etc/hosts.deny # /etc/hosts.deny: list of hosts that are _not_ allowed to access the system. # See the manual pages hosts_access(5) and hosts_options(5). # # Example: ALL: some.host.name, .some.domain # ALL EXCEPT in.fingerd: other.host.name, .other.domain # # If you're going to protect the portmapper use the name "portmap" for the # daemon name. Remember that you can only use the keyword "ALL" and IP # addresses (NOT host or domain names) for the portmapper, as well as for # rpc.mountd (the NFS mount daemon). See portmap(8) and rpc.mountd(8) # for further information. # # The PARANOID wildcard matches any host whose name does not match its # address. # # You may wish to enable this to ensure any programs that don't # validate looked up hostnames still leave understandable logs. In past # versions of Debian this has been the default. # ALL: PARANOID netstat -l: adp@adp-desktop:~$ netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost:52815 *:* LISTEN tcp 0 0 *:hylafax *:* LISTEN tcp 0 0 *:www *:* LISTEN tcp 0 0 *:4369 *:* LISTEN tcp 0 0 localhost:7634 *:* LISTEN tcp 0 0 *:ftp *:* LISTEN tcp 0 0 *:xmpp-server *:* LISTEN tcp 0 0 localhost:ipp *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 *:5280 *:* LISTEN tcp 0 0 adp-desktop:7777 *:* LISTEN tcp 0 0 *:33601 *:* LISTEN tcp 0 0 *:xmpp-client *:* LISTEN tcp 0 0 localhost:mysql *:* LISTEN tcp6 0 0 [::]:netbios-ssn [::]:* LISTEN tcp6 0 0 localhost:ipp [::]:* LISTEN tcp6 0 0 [::]:microsoft-ds [::]:* LISTEN udp 0 0 *:bootpc *:* udp 0 0 *:mdns *:* udp 0 0 *:47467 *:* udp 0 0 192.168.1.10:netbios-ns *:* udp 0 0 192.168.91.1:netbios-ns *:* udp 0 0 192.168.156.:netbios-ns *:* udp 0 0 *:netbios-ns *:* udp 0 0 192.168.1.1:netbios-dgm *:* udp 0 0 192.168.91.:netbios-dgm *:* udp 0 0 192.168.156:netbios-dgm *:* udp 0 0 *:netbios-dgm *:* raw 0 0 *:icmp *:* 7 netstat -rn: adp@adp-desktop:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.91.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet1 192.168.156.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet8 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 commands on the laptop, 192.168.1.102: ifconfig: root@fakeuser-laptop:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:33:a2:31:15 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:21 eth1 Link encap:Ethernet HWaddr 00:2d:d9:3e:1f:6c inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::21d:d9ff:fe3e:1f6c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5681 errors:0 dropped:0 overruns:0 frame:10313 TX packets:6717 errors:6 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4055251 (4.0 MB) TX bytes:779308 (779.3 KB) Interrupt:18 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:206 errors:0 dropped:0 overruns:0 frame:0 TX packets:206 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15172 (15.1 KB) TX bytes:15172 (15.1 KB) netstat -rn: root@fakeuser-laptop:~# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Deadlock in SQL Server 2005! Two real-time bulk upserts are fighting. WHY?

  - by skimania

  Here's the scenario: I've got a table called MarketDataCurrent (MDC) that has live updating stock prices. I've got one process called 'LiveFeed' which reads prices streaming from the wire, queues up inserts, and uses a 'bulk upload to temp table then insert/update to MDC table.' (BulkUpsert) I've got another process which then reads this data, computes other data, and then saves the results back into the same table, using a similar BulkUpsert stored proc. Thirdly, there are a multitude of users running a C# Gui polling the MDC table and reading updates from it. Now, during the day when the data is changing rapidly, things run pretty smoothly, but then, after market hours, we've recently started seeing an increasing number of Deadlock exceptions coming out of the database, nowadays we see 10-20 a day. The imporant thing to note here is that these happen when the values are NOT changing. Here's all the relevant info: Table Def: CREATE TABLE [dbo].[MarketDataCurrent]( [MDID] [int] NOT NULL, [LastUpdate] [datetime] NOT NULL, [Value] [float] NOT NULL, [Source] [varchar](20) NULL, CONSTRAINT [PK_MarketDataCurrent] PRIMARY KEY CLUSTERED ( [MDID] ASC )WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = ON) ON [PRIMARY] ) ON [PRIMARY] - I've got a Sql Profiler Trace Running, catching the deadlocks, and here's what all the graphs look like. Process 258 is called the following 'BulkUpsert' stored proc, repeatedly, while 73 is calling the next one: ALTER proc [dbo].[MarketDataCurrent_BulkUpload] @updateTime datetime, @source varchar(10) as begin transaction update c with (rowlock) set LastUpdate = getdate(), Value = t.Value, Source = @source from MarketDataCurrent c INNER JOIN #MDTUP t ON c.MDID = t.mdid where c.lastUpdate < @updateTime and c.mdid not in (select mdid from MarketData where LiveFeedTicker is not null and PriceSource like 'LiveFeed.%') and c.value <> t.value insert into MarketDataCurrent with (rowlock) select MDID, getdate(), Value, @source from #MDTUP where mdid not in (select mdid from MarketDataCurrent with (nolock)) and mdid not in (select mdid from MarketData where LiveFeedTicker is not null and PriceSource like 'LiveFeed.%') commit And the other one: ALTER PROCEDURE [dbo].[MarketDataCurrent_LiveFeedUpload] AS begin transaction -- Update existing mdid UPDATE c WITH (ROWLOCK) SET LastUpdate = t.LastUpdate, Value = t.Value, Source = t.Source FROM MarketDataCurrent c INNER JOIN #TEMPTABLE2 t ON c.MDID = t.mdid; -- Insert new MDID INSERT INTO MarketDataCurrent with (ROWLOCK) SELECT * FROM #TEMPTABLE2 WHERE MDID NOT IN (SELECT MDID FROM MarketDataCurrent with (NOLOCK)) -- Clean up the temp table DELETE #TEMPTABLE2 commit To clarify, those Temp Tables are being created by the C# code on the same connection and are populated using the C# SqlBulkCopy class. To me it looks like it's deadlocking on the PK of the table, so I tried removing that PK and switching to a Unique Constraint instead but that increased the number of deadlocks 10-fold. I'm totally lost as to what to do about this situation and am open to just about any suggestion. HELP!! In response to the request for the XDL, here it is: <deadlock-list> <deadlock victim="processc19978"> <process-list> <process id="processaf0b68" taskpriority="0" logused="0" waitresource="KEY: 6:72057594090487808 (d900ed5a6cc6)" waittime="718" ownerId="1102128174" transactionname="user_transaction" lasttranstarted="2010-06-11T16:30:44.750" XDES="0xffffffff817f9a40" lockMode="U" schedulerid="3" kpid="8228" status="suspended" spid="73" sbid="0" ecid="0" priority="0" transcount="2" lastbatchstarted="2010-06-11T16:30:44.750" lastbatchcompleted="2010-06-11T16:30:44.750" clientapp=".Net SqlClient Data Provider" hostname="RISKAPPS_VM" hostpid="3836" loginname="RiskOpt" isolationlevel="read committed (2)" xactid="1102128174" currentdb="6" lockTimeout="4294967295" clientoption1="671088672" clientoption2="128056"> <executionStack> <frame procname="MKP_RISKDB.dbo.MarketDataCurrent_BulkUpload" line="28" stmtstart="1062" stmtend="1720" sqlhandle="0x03000600a28e5e4ef4fd8e00849d00000100000000000000"> UPDATE c WITH (ROWLOCK) SET LastUpdate = getdate(), Value = t.Value, Source = @source FROM MarketDataCurrent c INNER JOIN #MDTUP t ON c.MDID = t.mdid WHERE c.lastUpdate &lt; @updateTime and c.mdid not in (select mdid from MarketData where BloombergTicker is not null and PriceSource like &apos;Blbg.%&apos;) and c.value &lt;&gt; t.value </frame> <frame procname="adhoc" line="1" stmtstart="88" sqlhandle="0x01000600c1653d0598706ca7000000000000000000000000"> exec MarketDataCurrent_BulkUpload @clearBefore, @source </frame> <frame procname="unknown" line="1" sqlhandle="0x000000000000000000000000000000000000000000000000"> unknown </frame> </executionStack> <inputbuf> (@clearBefore datetime,@source nvarchar(10))exec MarketDataCurrent_BulkUpload @clearBefore, @source </inputbuf> </process> <process id="processc19978" taskpriority="0" logused="0" waitresource="KEY: 6:72057594090487808 (74008e31572b)" waittime="718" ownerId="1102128228" transactionname="user_transaction" lasttranstarted="2010-06-11T16:30:44.780" XDES="0x380be9d8" lockMode="U" schedulerid="5" kpid="8464" status="suspended" spid="248" sbid="0" ecid="0" priority="0" transcount="2" lastbatchstarted="2010-06-11T16:30:44.780" lastbatchcompleted="2010-06-11T16:30:44.780" clientapp=".Net SqlClient Data Provider" hostname="RISKBBG_VM" hostpid="4480" loginname="RiskOpt" isolationlevel="read committed (2)" xactid="1102128228" currentdb="6" lockTimeout="4294967295" clientoption1="671088672" clientoption2="128056"> <executionStack> <frame procname="MKP_RISKDB.dbo.MarketDataCurrentBlbgRtUpload" line="14" stmtstart="840" stmtend="1220" sqlhandle="0x03000600005f9d24c8878f00849d00000100000000000000"> UPDATE c WITH (ROWLOCK) SET LastUpdate = t.LastUpdate, Value = t.Value, Source = t.Source FROM MarketDataCurrent c INNER JOIN #TEMPTABLE2 t ON c.MDID = t.mdid; -- Insert new MDID </frame> <frame procname="adhoc" line="1" sqlhandle="0x010006004a58132228bf8d73000000000000000000000000"> MarketDataCurrentBlbgRtUpload </frame> </executionStack> <inputbuf> MarketDataCurrentBlbgRtUpload </inputbuf> </process> </process-list> <resource-list> <keylock hobtid="72057594090487808" dbid="6" objectname="MKP_RISKDB.dbo.MarketDataCurrent" indexname="PK_MarketDataCurrent" id="lock5ba77b00" mode="U" associatedObjectId="72057594090487808"> <owner-list> <owner id="processc19978" mode="U"/> </owner-list> <waiter-list> <waiter id="processaf0b68" mode="U" requestType="wait"/> </waiter-list> </keylock> <keylock hobtid="72057594090487808" dbid="6" objectname="MKP_RISKDB.dbo.MarketDataCurrent" indexname="PK_MarketDataCurrent" id="lock65dca340" mode="U" associatedObjectId="72057594090487808"> <owner-list> <owner id="processaf0b68" mode="U"/> </owner-list> <waiter-list> <waiter id="processc19978" mode="U" requestType="wait"/> </waiter-list> </keylock> </resource-list> </deadlock> </deadlock-list>

  Read the article

• Streaming desktop with avconv - severe sound issues

  - by Tommy Brunn

  I'm trying to do some live streaming in Ubuntu 12.10, but I'm having some problems with audio. More specifically, the quality is complete garbage and it's at least 10 seconds out of sync with the video. I'm using an excellent guide found here to set up my loopback devices so that I can combine the desktop audio with the microphone input. It seems to work, as I'm able to stream both audio and video to Twitch.tv. But, as I said, the audio quality is terrible. The microphone audio is very, very low, but if I increase it, I get a horrible garbled sound that is absolutely unbearable. Nothing like that is present during VoIP calls or when recording sound alone with the sound recorder, so it's not an issue with the microphone itself. The entire audio stream is also delayed about 10-15 seconds compared to the video stream. I put together an imgur album of my settings. Here is some example output from when I'm streaming: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [x11grab @ 0x162fd80] device: :0.0+570,262 -> display: :0.0 x: 570 y: 262 width: 1280 height: 720 [x11grab @ 0x162fd80] shared memory extension found [x11grab @ 0x162fd80] Estimating duration from bitrate, this may be inaccurate Input #0, x11grab, from ':0.0+570,262': Duration: N/A, start: 1353181686.735113, bitrate: 884736 kb/s Stream #0.0: Video: rawvideo, bgra, 1280x720, 884736 kb/s, 30 tbr, 1000k tbn, 30 tbc [alsa @ 0x163fce0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x163fce0] Estimating duration from bitrate, this may be inaccurate Input #1, alsa, from 'pulse': Duration: N/A, start: 1353181686.773841, bitrate: N/A Stream #1.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s Incompatible pixel format 'bgra' for codec 'libx264', auto-selecting format 'yuv420p' [buffer @ 0x1641ec0] w:1280 h:720 pixfmt:bgra [scale @ 0x1642480] w:1280 h:720 fmt:bgra -> w:852 h:480 fmt:yuv420p flags:0x4 [libx264 @ 0x165ae80] VBV maxrate unspecified, assuming CBR [libx264 @ 0x165ae80] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x165ae80] profile Main, level 3.1 [libx264 @ 0x165ae80] 264 - core 123 r2189 35cf912 - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=2 deblock=1:0:0 analyse=0x1:0x111 me=hex subme=6 psy=1 psy_rd=1.00:0.00 mixed_ref=0 me_range=16 chroma_me=1 trellis=1 8x8dct=0 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=4 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=0 b_adapt=1 b_bias=0 direct=1 weightb=0 open_gop=1 weightp=1 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=30 rc=cbr mbtree=1 bitrate=712 ratetol=1.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 vbv_maxrate=712 vbv_bufsize=512 nal_hrd=none ip_ratio=1.25 aq=1:1.00 Output #0, flv, to 'rtmp://live.justin.tv/app/live_23011330_Pt1plSRM0z5WVNJ0QmCHvTPmpUnfC4': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: libx264, yuv420p, 852x480, q=-1--1, 712 kb/s, 1k tbn, 30 tbc Stream #0.1: Audio: libmp3lame, 44100 Hz, 2 channels, s16, 712 kb/s Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Stream #1:0 -> #0:1 (pcm_s16le -> libmp3lame) Press ctrl-c to stop encoding frame= 17 fps= 0 q=0.0 size= 0kB time=10000000000.00 bitrate= 0.0kbitframe= 32 fps= 31 q=0.0 size= 0kB time=10000000000.00 bitrate= 0.0kbitframe= 40 fps= 23 q=29.0 size= 44kB time=0.03 bitrate=13786.2kbits/s dup=frame= 47 fps= 21 q=31.0 size= 93kB time=2.73 bitrate= 277.7kbits/s dup=0frame= 62 fps= 23 q=29.0 size= 160kB time=3.23 bitrate= 406.2kbits/s dup=0frame= 77 fps= 24 q=23.0 size= 209kB time=3.71 bitrate= 462.5kbits/s dup=0frame= 92 fps= 25 q=20.0 size= 267kB time=4.91 bitrate= 445.2kbits/s dup=0frame= 107 fps= 25 q=20.0 size= 318kB time=5.41 bitrate= 482.1kbits/s dup=0frame= 123 fps= 26 q=18.0 size= 368kB time=5.96 bitrate= 505.7kbits/s dup=0frame= 139 fps= 26 q=16.0 size= 419kB time=6.48 bitrate= 529.7kbits/s dup=0frame= 155 fps= 27 q=15.0 size= 473kB time=7.00 bitrate= 553.6kbits/s dup=0frame= 170 fps= 27 q=14.0 size= 525kB time=7.52 bitrate= 571.7kbits/s dup=0 frame= 180 fps= 25 q=-1.0 Lsize= 652kB time=7.97 bitrate= 670.0kbits/s dup=0 drop=32 //Here I stop the streaming video:531kB audio:112kB global headers:0kB muxing overhead 1.345945% [libx264 @ 0x165ae80] frame I:1 Avg QP:30.43 size: 39748 [libx264 @ 0x165ae80] frame P:45 Avg QP:11.37 size: 11110 [libx264 @ 0x165ae80] frame B:134 Avg QP:15.93 size: 27 [libx264 @ 0x165ae80] consecutive B-frames: 0.6% 0.0% 1.7% 97.8% [libx264 @ 0x165ae80] mb I I16..4: 7.3% 0.0% 92.7% [libx264 @ 0x165ae80] mb P I16..4: 0.1% 0.0% 0.1% P16..4: 49.1% 1.2% 2.1% 0.0% 0.0% skip:47.4% [libx264 @ 0x165ae80] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 0.1% 0.0% 0.0% direct: 0.0% skip:99.9% L0:42.5% L1:56.9% BI: 0.6% [libx264 @ 0x165ae80] coded y,uvDC,uvAC intra: 82.3% 87.4% 71.9% inter: 7.1% 8.4% 7.0% [libx264 @ 0x165ae80] i16 v,h,dc,p: 27% 29% 16% 28% [libx264 @ 0x165ae80] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 22% 21% 14% 8% 8% 8% 7% 5% 7% [libx264 @ 0x165ae80] i8c dc,h,v,p: 47% 22% 20% 11% [libx264 @ 0x165ae80] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0x165ae80] ref P L0: 96.4% 3.6% [libx264 @ 0x165ae80] kb/s:474.19 Received signal 2: terminating. Any ideas on how I can resolve this? The video delay is perfectly acceptable, so I wouldn't think that it's a network issue that's causing the delay in the audio. Any help would be appreciated.

  Read the article

• Create dynamic buffer SharpDX

  - by fedab

  I want to set a buffer that is updated every frame but can't figure it out, what i have to do. The only working thing i have is this: mdexcription = new BufferDescription(Matrix.SizeInBytes * Matrices.Length, ResourceUsage.Dynamic, BindFlags.VertexBuffer, CpuAccessFlags.Write, ResourceOptionFlags.None, 0); instanceBuffer = SharpDX.Direct3D11.Buffer.Create(Device, Matrices, mdexcription); vBB = new VertexBufferBinding(instanceBuffer, Matrix.SizeInBytes, 0); DeviceContext.InputAssembler.SetVertexBuffers(1, vBB); Draw: //Change Matrices (Matrix[]) every frame... instanceBuffer.Dispose(); instanceBuffer = SharpDX.Direct3D11.Buffer.Create(Device, Matrices, mdexcription); vBB = new VertexBufferBinding(instanceBuffer, Matrix.SizeInBytes, 0); DeviceContext.InputAssembler.SetVertexBuffers(1, vBB); I guess Dispose() and creating a new buffer is slow and can be done much faster. I've read about DataStream but i do not know, how to set this up properly. What steps do i have to do to set up a DataStream to achieve fast every-frame update?

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >