Search Results

Search found 10798 results on 432 pages for 'port scanning'.

Page 34/432 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• Setting the Server Port in D-Link Router for eMailing Logs

  - by Synetech

  Does anyone know how to set the port for the email server in the Status->Log section of the D-Link DI-524? I’ve tried the setting below but it does not seem to work. I don’t want to use the default port 25 if I can avoid it. (No, the server and email address in the snap are irrelevant, you can replace the server with hotmail.com or whatever and address with a valid one; the question I am trying to figure out is how to set the port.)

  Read the article

• Pendrive not working on USB port - USB2 Enhanced Host Controller - 27CC

  - by user1664417

  I have a situation here, is kind of weird. Situation as below: If i enable the 'Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC' , then my pc will not be able to read any USB stick/pendrive, but usb port work fine with keyboard and mouse. If I disable the device driver, then all kind of pendrive can be read. Below is What i have done : 1) try the same pendrive on other pc, it work like charm. 2) try others pendrive on issue pc, same problem, but it work fine in others pc. 3) try all the port, including the port that connected to mouse n keyboard. 4) update the driver version. 5) restore default setting of usb in bios Please help to solve these issue if anyone experience it before. Many thanks.. :

  Read the article

• Cannot connect to ethernet port

  - by Jnir

  I'm running Ubuntu 12.04 LTE. I'm trying to connect via ethernet for the first time but have had no success. Ifconfig eth0 returns: eth0 Link encap:Ethernet HWaddr: 00:01:2e:3f:f1:a0 inet6 addr: fe80::201:2eff:fe3f:f1a0 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:68 errors:0 dropped:0 overruns:0 frame:0 TX packets:183 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8374 (8.3 KB) TX bytes:42944 (42.9KB) Interrupt:16 Base address:0x6c00 /etc/network/interfaces has auto lo iface lo inef loopback auto eth0 iface eth0 inet dhcp sudo /etc/init.d/networking prints: * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... Failed to bring up eth0 [OK]

  Read the article

• Windows XP/Firewall -- Can't open UDP port 9100 for JetDirect sharing

  - by Barton Chittenden

  I'm setting up my Dad's laptop (Vista) to print to an HP Deskjet printer attached to a Windows XP Desktop box. The XP box is running Windows firewall. Laptop sits on 192.168.1.66, Desktop 192.168.1.65. I set up logging in the firewall, and determined that it is dropping inbound packets on TCP port 9100, used by JetDirect, the printing protocol. I set up an exception on TCP port 9100, allowing access to the local subnet. There's also an entry under the 'allow applications' tab which was marked for the exact printer model. I selected this as well, then tried to print again... I see more dropped packets from 192.168.1.66 to 192.168.1.65 for TCP port 9100. What do I try next?

  Read the article

• How to access localhost remotely - Wordpress?

  - by Marcappuccino

  I have installed a LAMP stack (sudo tasksel install lamp-server) and wordpress (sudo apt-get install wordpress), but now, I would like to access my server remotely, to be used as a home fileserver. For example, my public ip is 82.16.xxx.xxx. Opening it in firefox with the suffix :8080 brings up my router config page..? Do I have to set up port forwarding? BTW. Accessing via localhost/wordpress/ works fine, I would just like to access my files while away from home.

  Read the article

• MSDTC Port 135 open bi-directionally

  - by Stephen Lacy

  I have two servers, a web application server and an SQL Server database running on its own server. I have a firewall between these two servers. Do I have to open port 135 on both the SQL Server and the Web Application Server. Does the SQL Server open its own connection to the Web Application Server on port 135 or any other port? Do I have to in component services point the Web Application Server MSDTC at the SQL Database Server? If the firewall is completely open, the settings in component services set to allow remote connections, remote administration etc is there any other settings that need to be changed in order to allow remote connections to the SQL Server MSDTC?

  Read the article

• MacBook Pro USB port provides more current in Mac OS X than in Windows

  - by AngryHacker

  I have a MacBook Pro with both Mac OS X Lion and Windows (under BootCamp) installed. While in Windows, I tried to charge my iPad 3 via the USB port. The iPad says "Not charging", but really, it does, just super slow (4-5% per hour). The reason for this is that the iPad requires 2.1 A of current, but a standard USB port provides 0.5 A. However, if I switch to Mac OS X, the iPad states that it is charging and it does at a rate of about 10% per hour. The only takeaway from this is that either OS X puts out more current on the USB port or that it recognizes the iPad and acts accordingly. Can someone provide more information on what is actually happening?

  Read the article

• Port forwarding with DNAT and SNAT without touching other packets

  - by w00t

  I have a Linux gateway with iptables which does routing and port forwarding. I want the port forwarding to happen independent of the routing. To port forward, I add this to the nat table: iptables -t nat -A "$PRE" -p tcp -d $GW --dport $fromPort -j DNAT --to-destination $toHost:$toPort iptables -t nat -A "$POST" -p tcp -d $toHost --dport $toPort -j SNAT --to $SRC $PRE and POST are actually destination-specific chains that I jump to from the PREROUTING and POSTROUTING chains respectively so I can keep the iptables clean. $SRC is the IP address I'm SNATing to which is different from the gateway IP $GW. The problem with this setup is that regular routed packets that were not DNATed but happen to go to the same $toHost:$toPort combo will also be SNATed. I wish to avoid this. Any clever things I can do?

  Read the article

• How do I get rid of sockets in FIN_WAIT1 state?

  - by Gert M

  I have a port that is blocked by a process I needed to kill. (a little telnet daemon that crashed) The process was killed successfully but the port is still in a 'FIN_WAIT1' state. It doesn't come out of it, the timeout for that seems to be set to 'a decade'. The only way I've found to free the port is to reboot the entire machine, which is ofcourse something I do not want to do. $ netstat -tulnap | grep FIN_WAIT1 tcp 0 13937 10.0.0.153:4000 10.0.2.46:2572 FIN_WAIT1 - Does anyone know how I can get this port unblocked without rebooting?

  Read the article

• Unable to do Port Forwarding in Virtual Box

  - by dewbot

  I'm using Mac OS X 10.6. I have installed Virtual Box 4.1.0 in it. My Guest OS is Ubuntu Server 11.04. I have added a rule in Port Forwarding in Virtual Box - "guestssh" TCP 127.0.1.1 8080 127.0.0.1 1337 Inside Guest OS I'm running nodejs server. Code is nothing but simple helloworld code found on their site http://nodejs.org/. In short I'm running server on 127.0.0.1 on 1337 Port. Now according to rule I have given, from Host Machine all the requests for 127.0.1.1:8080 should be forwarded to 127.0.0.1:1337 of Guest OS. From Host I'm doing curl http://127.0.1.1:8080 and I'm getting curl: (7) couldn't connect to host Is there something am I doing wrong? Note- Don't give me suggestion to do ssh n all. As my ISP does not provide Internal LAN so its not possible in my case. All I can do it Port Forwarding.

  Read the article

• Can't get nmap to work under Windows 7 64 bit

  - by jitbit

  I'm trying to install and run the nmap tool to test my server, but it keeps saying Note: Host seems down. If it is really up, but blocking our ping probes, try -P0 and showing all the server ports are closed. Which is not true - the server is up and has lots of open ports. Any ideas? UPDATE: Just to clarify - the server can be pinged and port-scanned fine by other programs. It's juts nmap that does not work. Even "google.com" seems to be down for nmap.

  Read the article

• display port on x230 not workgin

  - by Aaron

  having problems with my new lenovo x230 - using dual montiors, only vga registers anything. This has the Intel graphics controller : 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) TO get it to even boot, had to add the nomodeset parameter to the kernel. Otherwise will not even start up X Ive upgraded my kernel to the latest 3.6 with no difference. The display section reads the monitor as the only display and labels it as laptop. Cant seem to get it to work! Any help would be greatly appreciated.

  Read the article

• Windows Xp, Svchost.exe connecting to different ips with remote port 445

  - by Coll911

  Im using Windows Xp professional Sp2 Whenever i start my windows, svchost.exe starts connecting to all the possible ips on lan like from 192.168.1.2 to 192.168.1.200 The local port ranges from 1000-1099 and the remote port being 445. After its done with the local ips, it starts connecting to other random ips. I tried blocking connections to the port 445 using the local security polices but it didn't work Is there any possible way i could prevent svchost from connecting to these ips without involving any firewall installed ? since my pc slows down due to the load I'd be thankful for any advices

  Read the article

• Hooking domain to home server with port

  - by user1071461

  Alright, I'm asking two things here. First of all, if i purchase a domain let's say myhomeserver.com, am I able to make the default port go through a different port instead of the default port 80? (that is without having to do myhomeserver.com:5000 for example). Also this should be without blocking other ports (so no stealth forwarding to myhomeserver.com:5000 i think) Secondly, How could I go about hooking a domain to a windows 2008 server? I've seen it on linux but no clue how to do it on windows if it's even possible. I know I'm asking a lot here, just some tips are appereciated. Also, yes I know, using a home server is horrible for security and preformance and whatnot, I understand this already, thanks ^^

  Read the article

• Which TCP ports to use?

  - by rowatt

  Is there a TCP port range which I can be sure will not be used by anything else for traffic between two machines? If I am reading RFC6335 correctly, I can be sure that no other applications will use specific ports in the Dynamic/Private/Ephemeral range of 49152-65535. However, if I understand correctly, it also states (section 8.1.2) that an application shouldn't assume that any given port in that range is available at any given time, which would mean I can't be 100% sure that it will be unused all the time. Specifically, I want to assign specific SSH traffic to a different port for the security benefit and so I can classify it differently for QoS purposes, and not have to worry about changing the port in the future.

  Read the article

• telnet: Could not open connection to the host, on port 23

  - by Mihaela

  I need to telnet, to localhost. I am on windows. Once I got the error 'telnet is not recognized...' I looked online and found that I should do pkgmgr /iu:"TelnetClient". I did, then telnet localhost (0r 127.0.0.1, maybe with a port at the end), I get error: Could not open connection to the host, on port 23: Connect failed. I added the port to the firewall, disabled the firewall.. run as admin.. Please help me get telnet to work! Thank you.

  Read the article

• Block all ports except SSH/HTTP in ipchains and iptables

  - by user198003

  How can I block all ports except ssh (port 22) httpd (port 80) using iptables and iphains?

  Read the article

• Port an existing Quickly app from precise to quantal

  - by Ian B.

  I've developed an app using Quickly on a 12.04 system. In preparation for the 12.10 release, I'd like to have launchpad build a version for Quantal so that it can be used and tested by people from my ppa. I'm not willing to upgrade my system yet (I depend on it for work), how can I do this from 12.04 and my current quickly project? I have a virtualbox with 12.10 installed for testing, but I don't want to copy over the quickly project if I don't have to. Ideally, an answer should work with the quickly submitubuntu command so that it is packaged for installation in the /opt/extras.ubuntu.com directory.

  Read the article

• Access to a network server without port forwarding

  - by SdevDavid

  I have a network with the following structure. The server in PC2 is simple socket server TCP in 8080 port. I need to access to PC2 from other external network by socket client. This socket client knows the public IP (85.xxx.xxx.x), the private IP (192.168.0.21) and the port. How I can access PC2 without port forwarding on the router? If possible, I would like to have a reference in any programming language of this case.

  Read the article

• Hooking domain to home server (WinServer2008) with specific port

  - by user1071461

  Alright, I'm asking two things here. First of all, if i purchase a domain let's say myhomeserver.com, am I able to make the default port go through a different port instead of the default port 80? (that is without having to do myhomeserver.com:5000 for example). Also this should be without blocking other ports (so no stealth forwarding to myhomeserver.com:5000 i think) Secondly, How could I go about hooking a domain to a windows 2008 server? I've seen it on linux but no clue how to do it on windows if it's even possible. I know I'm asking a lot here, just some tips are appereciated. Also, yes I know, using a home server is horrible for security and preformance and whatnot, I understand this already, thanks ^^

  Read the article

• UFW blocking webrick on port 3000

  - by t Book

  On a ubuntu 10.0.4 server runs redmine. starting webrick with: ./server webrick -e production -b lvps46-173-79-113.dedicated.hosteurope.de -d makes redmine available in browser. as soon as we enable ufw, webrick can´t be accessed anymore. of course we allowed Port 3000 from anywhere ufw allow 3000/tcp ufw allow 3000/udp also a grep for iptables doesn´t show a deny rule iptables -nL | grep 3000 find the whole iptables output here http://pastebin.com/k6WNqdPU checking lsof -ni tcp:2222 tells me ruby is listening on port 3000 ruby 3457 root 5u IPv4 864846667 0t0 TCP 46.173.79.113:3000 (LISTEN) What else can we check? what´s wrong with the ufw rules for port 3000?

  Read the article

• Port forwarding (portmap) works only locally

  - by Tag Wint

  There are four hosts hostA winXP hostB Win2003 hostC Linux RHEL hostD Linux RHEL hostA cannot connect to C and D directly, but B can hostA connects to hostB using VPN hostB and hostC belong to the same subnet1 hostD is in subnet2 From hostA I need to connect to hostC and hostD by SSH. Now I can do it as follows: 1.connecting from hostA to hostB by RDP logon and there: 2.start putty client. I'd like to omit step 1 and connect from A to C and D directly On hostB I have admin acoount and configure port forwarding as follows: netsh interface portproxy add v4tov4 listenport=N1 connectaddress=hostC_IP connectport=N2 netsh interface portproxy add v4tov4 listenport=N3 connectaddress=hostD_IP connectport=N2 netsh interface portproxy show all: Listen on IPv4: Connect to IPv4: Address Port Address Port --------------- ---------- --------------- ---------- * N1 hostC_IP N2 * N3 hostD_IP N2 Now from hostB I can connect to either C and D: ssh localhost:N1 ssh localhost:N3 from hostA ssh hostB:N1 works too, but ssh hostB:N3 DON'T I guess the reason might be different subnets, still have no idea how to fix it. What should I do?

  Read the article

• Unable to launch the asp.net development server because port '80' is in use

  - by kevin

  I need to use port 80 for my development server. Before i restart pc, it's still working fine. After that, it pop up the port 80 is in use. The development server able to run if i changed to other port. I've checked using netstat -ano, no program is using it (my iis is using other port and my skype is not using port 80 as well). I also test with telnet localhost 80, it didnt show any failure message, just the screen goes blank...I'm using win xp. Is my visual studio has problem?

  Read the article

• How can I listen to multiple Serial Ports asynchronously in C#

  - by Kamiel Wanrooij

  I have an application that listens to a piece of hardware on a USB to Serial converter. My application should monitor more than one serial port at the same time. I loop the serial ports I need to listen to, and create a thread for each port. In the thread I have my data handing routine. When I assign one port, it runs flawlessly. When I listen to the other one, it also works. When I open both ports however, the second port always throws an UnauthorizedAccessException when calling serialPort.Open(). It does not matter in what order I open the ports, the second one always fails. I listen to the ports using serialPort.ReadLine() in a while loop. Can .NET open more than one port at the same time? Can I listen to both? Or should I use another (thread safe?) way to access my serial port events?

  Read the article

• C# SerialPort.GetPortNames() behavior

  - by Gunner

  In my C# 2008 application, I use the SerialPort.GetPortNames() function to retrieve the list of currently available ports. What I have noticed is, when ever I plug in a USB device, it's port number i s shown in the list on my Application and when I unplug it and refresh the list, the port number is no longer there. One phase of the application involves reading/writing data from/to the device continuously. Now, my expectation is, If I unplug the device during the operation and get the current Port list using SerialPort.GetPortNames(), the Port Name will not be there and I can use that to make the decision that the device has been unplugged. To my surprise, the Port name is still found despite having it removed Why is the program behaving like this? The port name isn't listed when in no-communication mode. Does it have something to do with the device being removed when it's communicating?

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >