Search Results

Search found 2697 results on 108 pages for 'tan kah ping'.

Page 34/108 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

  • Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

    - by Lucas
    I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

    Read the article

  • How to parse nagios status.dat file?

    - by daniels
    I'd like to parse status.dat file for nagios3 and output as xml with a python script. The xml part is the easy one but how do I go about parsing the file? Use multi line regex? It's possible the file will be large as many hosts and services are monitored, will loading the whole file in memory be wise? I only need to extract services that have critical state and host they belong to. Any help and pointing in the right direction will be highly appreciated. LE Here's how the file looks: ######################################## # NAGIOS STATUS FILE # # THIS FILE IS AUTOMATICALLY GENERATED # BY NAGIOS. DO NOT MODIFY THIS FILE! ######################################## info { created=1233491098 version=2.11 } program { modified_host_attributes=0 modified_service_attributes=0 nagios_pid=15015 daemon_mode=1 program_start=1233490393 last_command_check=0 last_log_rotation=0 enable_notifications=1 active_service_checks_enabled=1 passive_service_checks_enabled=1 active_host_checks_enabled=1 passive_host_checks_enabled=1 enable_event_handlers=1 obsess_over_services=0 obsess_over_hosts=0 check_service_freshness=1 check_host_freshness=0 enable_flap_detection=0 enable_failure_prediction=1 process_performance_data=0 global_host_event_handler= global_service_event_handler= total_external_command_buffer_slots=4096 used_external_command_buffer_slots=0 high_external_command_buffer_slots=0 total_check_result_buffer_slots=4096 used_check_result_buffer_slots=0 high_check_result_buffer_slots=2 } host { host_name=localhost modified_attributes=0 check_command=check-host-alive event_handler= has_been_checked=1 should_be_scheduled=0 check_execution_time=0.019 check_latency=0.000 check_type=0 current_state=0 last_hard_state=0 plugin_output=PING OK - Packet loss = 0%, RTA = 3.57 ms performance_data= last_check=1233490883 next_check=0 current_attempt=1 max_attempts=10 state_type=1 last_state_change=1233489475 last_hard_state_change=1233489475 last_time_up=1233490883 last_time_down=0 last_time_unreachable=0 last_notification=0 next_notification=0 no_more_notifications=0 current_notification_number=0 notifications_enabled=1 problem_has_been_acknowledged=0 acknowledgement_type=0 active_checks_enabled=1 passive_checks_enabled=1 event_handler_enabled=1 flap_detection_enabled=1 failure_prediction_enabled=1 process_performance_data=1 obsess_over_host=1 last_update=1233491098 is_flapping=0 percent_state_change=0.00 scheduled_downtime_depth=0 } service { host_name=gateway service_description=PING modified_attributes=0 check_command=check_ping!100.0,20%!500.0,60% event_handler= has_been_checked=1 should_be_scheduled=1 check_execution_time=4.017 check_latency=0.210 check_type=0 current_state=0 last_hard_state=0 current_attempt=1 max_attempts=4 state_type=1 last_state_change=1233489432 last_hard_state_change=1233489432 last_time_ok=1233491078 last_time_warning=0 last_time_unknown=0 last_time_critical=0 plugin_output=PING OK - Packet loss = 0%, RTA = 2.98 ms performance_data= last_check=1233491078 next_check=1233491378 current_notification_number=0 last_notification=0 next_notification=0 no_more_notifications=0 notifications_enabled=1 active_checks_enabled=1 passive_checks_enabled=1 event_handler_enabled=1 problem_has_been_acknowledged=0 acknowledgement_type=0 flap_detection_enabled=1 failure_prediction_enabled=1 process_performance_data=1 obsess_over_service=1 last_update=1233491098 is_flapping=0 percent_state_change=0.00 scheduled_downtime_depth=0 } It can have any number of hosts and a host can have any number of services.

    Read the article

  • How do I configure a C# web service client to send HTTP request header and body in parallel?

    - by Christopher
    Hi, I am using a traditional C# web service client generated in VS2008 .Net 3.5, inheriting from SoapHttpClientProtocol. This is connecting to a remote web service written in Java. All configuration is done in code during client initialization, and can be seen below: ServicePointManager.Expect100Continue = false; ServicePointManager.DefaultConnectionLimit = 10; var client = new APIService { EnableDecompression = true, Url = _url + "?guid=" + Guid.NewGuid(), Credentials = new NetworkCredential(user, password, null), PreAuthenticate = true, Timeout = 5000 // 5 sec }; It all works fine, but the time taken to execute the simplest method call is almost double the network ping time. Whereas a Java test client takes roughly the same as the network ping time: C# client ~ 550ms Java client ~ 340ms Network ping ~ 300ms After analyzing the TCP traffic for a session discovered the following: Basically, the C# client sent TCP packets in the following sequence. Client Send HTTP Headers in one packet. Client Waits For TCP ACK from server. Client Sends HTTP Body in one packet. Client Waits For TCP ACK from server. The Java client sent TCP packets in the following sequence. Client Sends HTTP Headers in one packet. Client Sends HTTP Body in one packet. Client Revieves ACK for first packet. Client Revieves ACK for second packet. Client Revieves ACK for second packet. Is there anyway to configure the C# web service client to send the header/body in parallel as the Java client appears to? Any help or pointers much appreciated.

    Read the article

  • Ray Generation Inconsistency

    - by Myx
    I have written code that generates a ray from the "eye" of the camera to the viewing plane some distance away from the camera's eye: R3Ray ConstructRayThroughPixel(...) { R3Point p; double increments_x = (lr.X() - ul.X())/(double)width; double increments_y = (ul.Y() - lr.Y())/(double)height; p.SetX( ul.X() + ((double)i_pos+0.5)*increments_x ); p.SetY( lr.Y() + ((double)j_pos+0.5)*increments_y ); p.SetZ( lr.Z() ); R3Vector v = p-camera_pos; R3Ray new_ray(camera_pos,v); return new_ray; } ul is the upper left corner of the viewing plane and lr is the lower left corner of the viewing plane. They are defined as follows: R3Point org = scene->camera.eye + scene->camera.towards * radius; R3Vector dx = scene->camera.right * radius * tan(scene->camera.xfov); R3Vector dy = scene->camera.up * radius * tan(scene->camera.yfov); R3Point lr = org + dx - dy; R3Point ul = org - dx + dy; Here, org is the center of the viewing plane with radius being the distance between the viewing plane and the camera eye, dx and dy are the displacements in the x and y directions from the center of the viewing plane. The ConstructRayThroughPixel(...) function works perfectly for a camera whose eye is at (0,0,0). However, when the camera is at some different position, not all needed rays are produced for the image. Any suggestions what could be going wrong? Maybe something wrong with my equations? Thanks for the help.

    Read the article

  • EasyHook Windows Hooking problem/.dll injection

    - by Tom
    Ok can someone try and find the error with this code, it should produce all the registry keys every time something accesses them but i keep getting: System.MissingMethodException: The given method does not exist at EasyHook.LocalHook.GetProcAdress(String InModule, String InChannelName) An example code can be found here: http://www.codeproject.com/KB/DLL/EasyHook64.aspx I can get the CcreateFileW example to work! My code is here: public class Main : EasyHook.IEntryPoint { FileMon.FileMonInterface Interface; LocalHook LocalHook; Stack<String> Queue = new Stack<String>(); public Main(RemoteHooking.IContext InContext,String InChannelName) { // connect to host... Interface = RemoteHooking.IpcConnectClient<FileMon.FileMonInterface>(InChannelName); Interface.Ping(); } public void Run(RemoteHooking.IContext InContext,String InChannelName) { // install hook... try { LocalHook localHook = LocalHook.Create(LocalHook.GetProcAddress("Advapi32.dll", "RegOpenKeyExW"),new DMyRegOpenKeyExW(MyRegOpenKeyExW),this); localHook.ThreadACL.SetExclusiveACL(new int[] { }); } catch (Exception ExtInfo) { Interface.ReportException(ExtInfo); return; } Interface.IsInstalled(RemoteHooking.GetCurrentProcessId()); RemoteHooking.WakeUpProcess(); // wait for host process termination... try { while (true) { Thread.Sleep(500); // transmit newly monitored file accesses... if (Queue.Count > 0) { String[] Package = null; lock (Queue) { Package = Queue.ToArray(); Queue.Clear(); } Interface.OnCreateFile(RemoteHooking.GetCurrentProcessId(), Package); } else Interface.Ping(); } } catch { // Ping() will raise an exception if host is unreachable } } [DllImport("Advapi32.dll", CharSet = CharSet.Unicode, SetLastError = true, CallingConvention = CallingConvention.StdCall)] static extern int RegOpenKeyExW(UIntPtr hKey,string subKey,int ulOptions,int samDesired,out UIntPtr hkResult); [UnmanagedFunctionPointer(CallingConvention.StdCall, CharSet = CharSet.Unicode, SetLastError = true)] delegate int DMyRegOpenKeyExW(UIntPtr hKey,string subKey,int ulOptions,int samDesired,out UIntPtr hkResult); int MyRegOpenKeyExW(UIntPtr hKey,string subKey,int ulOptions,int samDesired,out UIntPtr hkResult) { Console.WriteLine(string.Format("Accessing: {0}", subKey)); return RegOpenKeyExW(hKey, subKey, ulOptions, samDesired, out hkResult); } }

    Read the article

  • what does this attempted trojan horse code do?

    - by bstullkid
    It looks like this just sends a ping, but whats the point of that when you can just use ping? /* WARNING: this is someone's attempt at writing a malware trojan. Do not compile and *definitely* don't install. I added an exit as the first line to avoid mishaps - msw */ int main (int argc, char *argv[]) { exit(1); unsigned int pid = 0; char buffer[2]; char *args[] = { "/bin/ping", "-c", "5", NULL, NULL }; if (argc != 2) return 0; args[3] = strdup(argv[1]); for (;;) { gets(buffer); /* FTW */ if (buffer[0] == 0x6e) break; switch (pid = fork()) { case -1: printf("Error Forking\n"); exit(255); case 0: execvp(args[0], args); exit(1); default: break; } } return 255; }

    Read the article

  • Accelerometer gravity components

    - by Dvd
    Hi, I know this question is definitely solved somewhere many times already, please enlighten me if you know of their existence, thanks. Quick rundown: I want to compute from a 3 axis accelerometer the gravity component on each of these 3 axes. I have used 2 axes free body diagrams to work out the accelerometer's gravity component in the world X-Z, Y-Z and X-Y axes. But the solution seems slightly off, it's acceptable for extreme cases when only 1 accelerometer axis is exposed to gravity, but for a pitch and roll of both 45 degrees, the combined total magnitude is greater than gravity (obtained by Xa^2+Ya^2+Za^2=g^2; Xa, Ya and Za are accelerometer readings in its X, Y and Z axis). More detail: The device is a Nexus One, and have a magnetic field sensor for azimuth, pitch and roll in addition to the 3-axis accelerometer. In the world's axis (with Z in the same direction as gravity, and either X or Y points to the north pole, don't think this matters much?), I assumed my device has a pitch (P) on the Y-Z axis, and a roll (R) on the X-Z axis. With that I used simple trig to get: Sin(R)=Ax/Gxz Cos(R)=Az/Gxz Tan(R)=Ax/Az There is another set for pitch, P. Now I defined gravity to have 3 components in the world's axis, a Gxz that is measurable only in the X-Z axis, a Gyz for Y-Z, and a Gxy for X-Y axis. Gxz^2+Gyz^2+Gxy^2=2*G^2 the 2G is because gravity is effectively included twice in this definition. Oh and the X-Y axis produce something more exotic... I'll explain if required later. From these equations I obtained a formula for Az, and removed the tan operations because I don't know how to handle tan90 calculations (it's infinity?). So my question is, anyone know whether I did this right/wrong or able to point me to the right direction? Thanks! Dvd

    Read the article

  • Is Stream.Write thread-safe?

    - by Mike Spross
    I'm working on a client/server library for a legacy RPC implementation and was running into issues where the client would sometimes hang when waiting to a receive a response message to an RPC request message. It turns out the real problem was in my message framing code (I wasn't handling message boundaries correctly when reading data off the underlying NetworkStream), but it also made me suspicious of the code I was using to send data across the network, specifically in the case where the RPC server sends a large amount of data to a client as the result of a client RPC request. My send code uses a BinaryWriter to write a complete "message" to the underlying NetworkStream. The RPC protocol also implements a heartbeat algorithm, where the RPC server sends out PING messages every 15 seconds. The pings are sent out by a separate thread, so, at least in theory, a ping can be sent while the server is in the middle of streaming a large response back to a client. Suppose I have a Send method as follows, where stream is a NetworkStream: public void Send(Message message) { //Write the message to a temporary stream so we can send it all-at-once MemoryStream tempStream = new MemoryStream(); message.WriteToStream(tempStream); //Write the serialized message to the stream. //The BinaryWriter is a little redundant in this //simplified example, but here because //the production code uses it. byte[] data = tempStream.ToArray(); BinaryWriter bw = new BinaryWriter(stream); bw.Write(data, 0, data.Length); bw.Flush(); } So the question I have is, is the call to bw.Write (and by implication the call to the underlying Stream's Write method) atomic? That is, if a lengthy Write is still in progress on the sending thread, and the heartbeat thread kicks in and sends a PING message, will that thread block until the original Write call finishes, or do I have to add explicit synchronization to the Send method to prevent the two Send calls from clobbering the stream?

    Read the article

  • Cannot change font size /type in plots

    - by Sameet Nabar
    I recently had to re-install my operating system (Ubuntu). The only thing I did differently is that I installed Matlab on a separate partition, not the main Ubuntu partition. After re-installing, the fonts in my plots are no longer configurable. For example, if I ask the title font to be bold, it doesn't happen. I ran the sample code below on my computer and then on my colleague's computer and the 2 results are attached. This cannot be a problem with the code; rather in the settings of Matlab. Could somebody please tell me what settings I need to change? Thanks in advance for your help. Regards, Sameet. x1=-pi:.1:pi; x2=-pi:pi/10:pi; y1=sin(x1); y2=tan(sin(x2)) - sin(tan(x2)); [AX,H1,H2]=plotyy(x1,y1,x2,y2); xlabel ('Time (hh:mm)'); ylabel (AX(1), 'Plot1'); ylabel (AX(2), 'Plot2'); axes(AX(2)) set(H1,'linestyle','none','marker','.'); set(H2,'linestyle','none','marker','.'); title('Plot Title','FontWeight','bold'); set(gcf, 'Visible', 'off'); [legh, objh] = legend([H1 H2],'Plot1', 'Plot2','location','Best'); set(legend,'FontSize',8); print -dpng Trial.png; Bad image: http://imageshack.us/photo/my-images/708/trial1u.png/ Good image: http://imageshack.us/photo/my-images/87/trial2.png/

    Read the article

  • Triangulation in 3D Space

    - by w3b_wizzard
    Disclaimer: This is for class, however I'm fresh out of ideas and a nudge in the right direction would be much appreciated. Also, this needs to be implemented in raw C, so no fancy libraries can be used. I have to write a search and rescue simulator for submarines, it has to find a probe that is randomly placed in 3D space in a grid from of the MAX_XYZ (100000). The only tools I'm given are a "ping" which will give the magnitude of the distance between a certain sub and the probe. The goal is to optimize the costs of this entire operation so a brute force attempt, like looking at every single coordinate, won't work. Hence I was thinking triangulation. Now, it makes loads of sense to me, place three subs, each one of them uses their ping to get the distance between them and the probe. Since each sub have a known distance relative to one another, it's easy to build the base of a tetrahedron with them, and the results of the ping will point to a certain coordinate, the problem I'm having is how to figure out the elevation, or the height, of the tetrahedron. So what I have as data is the following: Distances between subs (In vector format) Angles between each subs (very easy to compute) Distance between each sub and the probe (3 segments from the base to the peak) Angles inside each of the outer 3 surfaces of the tetrahedron. I tried finding some sort of relationship with the vertices of the tetrahedron and the relative angles in each of them, however all I found had to deal with tetrahedrons built with equilateral triangles, which isn't much help. I have the impression this can be easily solved with trig but either I'm not seeing it or I need more coffee. Any suggestions would be appreciated!

    Read the article

  • Toorcon14

    - by danx
    Toorcon 2012 Information Security Conference San Diego, CA, http://www.toorcon.org/ Dan Anderson, October 2012 It's almost Halloween, and we all know what that means—yes, of course, it's time for another Toorcon Conference! Toorcon is an annual conference for people interested in computer security. This includes the whole range of hackers, computer hobbyists, professionals, security consultants, press, law enforcement, prosecutors, FBI, etc. We're at Toorcon 14—see earlier blogs for some of the previous Toorcon's I've attended (back to 2003). This year's "con" was held at the Westin on Broadway in downtown San Diego, California. The following are not necessarily my views—I'm just the messenger—although I could have misquoted or misparaphrased the speakers. Also, I only reviewed some of the talks, below, which I attended and interested me. MalAndroid—the Crux of Android Infections, Aditya K. Sood Programming Weird Machines with ELF Metadata, Rebecca "bx" Shapiro Privacy at the Handset: New FCC Rules?, Valkyrie Hacking Measured Boot and UEFI, Dan Griffin You Can't Buy Security: Building the Open Source InfoSec Program, Boris Sverdlik What Journalists Want: The Investigative Reporters' Perspective on Hacking, Dave Maas & Jason Leopold Accessibility and Security, Anna Shubina Stop Patching, for Stronger PCI Compliance, Adam Brand McAfee Secure & Trustmarks — a Hacker's Best Friend, Jay James & Shane MacDougall MalAndroid—the Crux of Android Infections Aditya K. Sood, IOActive, Michigan State PhD candidate Aditya talked about Android smartphone malware. There's a lot of old Android software out there—over 50% Gingerbread (2.3.x)—and most have unpatched vulnerabilities. Of 9 Android vulnerabilities, 8 have known exploits (such as the old Gingerbread Global Object Table exploit). Android protection includes sandboxing, security scanner, app permissions, and screened Android app market. The Android permission checker has fine-grain resource control, policy enforcement. Android static analysis also includes a static analysis app checker (bouncer), and a vulnerablity checker. What security problems does Android have? User-centric security, which depends on the user to grant permission and make smart decisions. But users don't care or think about malware (the're not aware, not paranoid). All they want is functionality, extensibility, mobility Android had no "proper" encryption before Android 3.0 No built-in protection against social engineering and web tricks Alternative Android app markets are unsafe. Simply visiting some markets can infect Android Aditya classified Android Malware types as: Type A—Apps. These interact with the Android app framework. For example, a fake Netflix app. Or Android Gold Dream (game), which uploads user files stealthy manner to a remote location. Type K—Kernel. Exploits underlying Linux libraries or kernel Type H—Hybrid. These use multiple layers (app framework, libraries, kernel). These are most commonly used by Android botnets, which are popular with Chinese botnet authors What are the threats from Android malware? These incude leak info (contacts), banking fraud, corporate network attacks, malware advertising, malware "Hackivism" (the promotion of social causes. For example, promiting specific leaders of the Tunisian or Iranian revolutions. Android malware is frequently "masquerated". That is, repackaged inside a legit app with malware. To avoid detection, the hidden malware is not unwrapped until runtime. The malware payload can be hidden in, for example, PNG files. Less common are Android bootkits—there's not many around. What they do is hijack the Android init framework—alteering system programs and daemons, then deletes itself. For example, the DKF Bootkit (China). Android App Problems: no code signing! all self-signed native code execution permission sandbox — all or none alternate market places no robust Android malware detection at network level delayed patch process Programming Weird Machines with ELF Metadata Rebecca "bx" Shapiro, Dartmouth College, NH https://github.com/bx/elf-bf-tools @bxsays on twitter Definitions. "ELF" is an executable file format used in linking and loading executables (on UNIX/Linux-class machines). "Weird machine" uses undocumented computation sources (I think of them as unintended virtual machines). Some examples of "weird machines" are those that: return to weird location, does SQL injection, corrupts the heap. Bx then talked about using ELF metadata as (an uintended) "weird machine". Some ELF background: A compiler takes source code and generates a ELF object file (hello.o). A static linker makes an ELF executable from the object file. A runtime linker and loader takes ELF executable and loads and relocates it in memory. The ELF file has symbols to relocate functions and variables. ELF has two relocation tables—one at link time and another one at loading time: .rela.dyn (link time) and .dynsym (dynamic table). GOT: Global Offset Table of addresses for dynamically-linked functions. PLT: Procedure Linkage Tables—works with GOT. The memory layout of a process (not the ELF file) is, in order: program (+ heap), dynamic libraries, libc, ld.so, stack (which includes the dynamic table loaded into memory) For ELF, the "weird machine" is found and exploited in the loader. ELF can be crafted for executing viruses, by tricking runtime into executing interpreted "code" in the ELF symbol table. One can inject parasitic "code" without modifying the actual ELF code portions. Think of the ELF symbol table as an "assembly language" interpreter. It has these elements: instructions: Add, move, jump if not 0 (jnz) Think of symbol table entries as "registers" symbol table value is "contents" immediate values are constants direct values are addresses (e.g., 0xdeadbeef) move instruction: is a relocation table entry add instruction: relocation table "addend" entry jnz instruction: takes multiple relocation table entries The ELF weird machine exploits the loader by relocating relocation table entries. The loader will go on forever until told to stop. It stores state on stack at "end" and uses IFUNC table entries (containing function pointer address). The ELF weird machine, called "Brainfu*k" (BF) has: 8 instructions: pointer inc, dec, inc indirect, dec indirect, jump forward, jump backward, print. Three registers - 3 registers Bx showed example BF source code that implemented a Turing machine printing "hello, world". More interesting was the next demo, where bx modified ping. Ping runs suid as root, but quickly drops privilege. BF modified the loader to disable the library function call dropping privilege, so it remained as root. Then BF modified the ping -t argument to execute the -t filename as root. It's best to show what this modified ping does with an example: $ whoami bx $ ping localhost -t backdoor.sh # executes backdoor $ whoami root $ The modified code increased from 285948 bytes to 290209 bytes. A BF tool compiles "executable" by modifying the symbol table in an existing ELF executable. The tool modifies .dynsym and .rela.dyn table, but not code or data. Privacy at the Handset: New FCC Rules? "Valkyrie" (Christie Dudley, Santa Clara Law JD candidate) Valkyrie talked about mobile handset privacy. Some background: Senator Franken (also a comedian) became alarmed about CarrierIQ, where the carriers track their customers. Franken asked the FCC to find out what obligations carriers think they have to protect privacy. The carriers' response was that they are doing just fine with self-regulation—no worries! Carriers need to collect data, such as missed calls, to maintain network quality. But carriers also sell data for marketing. Verizon sells customer data and enables this with a narrow privacy policy (only 1 month to opt out, with difficulties). The data sold is not individually identifiable and is aggregated. But Verizon recommends, as an aggregation workaround to "recollate" data to other databases to identify customers indirectly. The FCC has regulated telephone privacy since 1934 and mobile network privacy since 2007. Also, the carriers say mobile phone privacy is a FTC responsibility (not FCC). FTC is trying to improve mobile app privacy, but FTC has no authority over carrier / customer relationships. As a side note, Apple iPhones are unique as carriers have extra control over iPhones they don't have with other smartphones. As a result iPhones may be more regulated. Who are the consumer advocates? Everyone knows EFF, but EPIC (Electrnic Privacy Info Center), although more obsecure, is more relevant. What to do? Carriers must be accountable. Opt-in and opt-out at any time. Carriers need incentive to grant users control for those who want it, by holding them liable and responsible for breeches on their clock. Location information should be added current CPNI privacy protection, and require "Pen/trap" judicial order to obtain (and would still be a lower standard than 4th Amendment). Politics are on a pro-privacy swing now, with many senators and the Whitehouse. There will probably be new regulation soon, and enforcement will be a problem, but consumers will still have some benefit. Hacking Measured Boot and UEFI Dan Griffin, JWSecure, Inc., Seattle, @JWSdan Dan talked about hacking measured UEFI boot. First some terms: UEFI is a boot technology that is replacing BIOS (has whitelisting and blacklisting). UEFI protects devices against rootkits. TPM - hardware security device to store hashs and hardware-protected keys "secure boot" can control at firmware level what boot images can boot "measured boot" OS feature that tracks hashes (from BIOS, boot loader, krnel, early drivers). "remote attestation" allows remote validation and control based on policy on a remote attestation server. Microsoft pushing TPM (Windows 8 required), but Google is not. Intel TianoCore is the only open source for UEFI. Dan has Measured Boot Tool at http://mbt.codeplex.com/ with a demo where you can also view TPM data. TPM support already on enterprise-class machines. UEFI Weaknesses. UEFI toolkits are evolving rapidly, but UEFI has weaknesses: assume user is an ally trust TPM implicitly, and attached to computer hibernate file is unprotected (disk encryption protects against this) protection migrating from hardware to firmware delays in patching and whitelist updates will UEFI really be adopted by the mainstream (smartphone hardware support, bank support, apathetic consumer support) You Can't Buy Security: Building the Open Source InfoSec Program Boris Sverdlik, ISDPodcast.com co-host Boris talked about problems typical with current security audits. "IT Security" is an oxymoron—IT exists to enable buiness, uptime, utilization, reporting, but don't care about security—IT has conflict of interest. There's no Magic Bullet ("blinky box"), no one-size-fits-all solution (e.g., Intrusion Detection Systems (IDSs)). Regulations don't make you secure. The cloud is not secure (because of shared data and admin access). Defense and pen testing is not sexy. Auditors are not solution (security not a checklist)—what's needed is experience and adaptability—need soft skills. Step 1: First thing is to Google and learn the company end-to-end before you start. Get to know the management team (not IT team), meet as many people as you can. Don't use arbitrary values such as CISSP scores. Quantitive risk assessment is a myth (e.g. AV*EF-SLE). Learn different Business Units, legal/regulatory obligations, learn the business and where the money is made, verify company is protected from script kiddies (easy), learn sensitive information (IP, internal use only), and start with low-hanging fruit (customer service reps and social engineering). Step 2: Policies. Keep policies short and relevant. Generic SANS "security" boilerplate policies don't make sense and are not followed. Focus on acceptable use, data usage, communications, physical security. Step 3: Implementation: keep it simple stupid. Open source, although useful, is not free (implementation cost). Access controls with authentication & authorization for local and remote access. MS Windows has it, otherwise use OpenLDAP, OpenIAM, etc. Application security Everyone tries to reinvent the wheel—use existing static analysis tools. Review high-risk apps and major revisions. Don't run different risk level apps on same system. Assume host/client compromised and use app-level security control. Network security VLAN != segregated because there's too many workarounds. Use explicit firwall rules, active and passive network monitoring (snort is free), disallow end user access to production environment, have a proxy instead of direct Internet access. Also, SSL certificates are not good two-factor auth and SSL does not mean "safe." Operational Controls Have change, patch, asset, & vulnerability management (OSSI is free). For change management, always review code before pushing to production For logging, have centralized security logging for business-critical systems, separate security logging from administrative/IT logging, and lock down log (as it has everything). Monitor with OSSIM (open source). Use intrusion detection, but not just to fulfill a checkbox: build rules from a whitelist perspective (snort). OSSEC has 95% of what you need. Vulnerability management is a QA function when done right: OpenVas and Seccubus are free. Security awareness The reality is users will always click everything. Build real awareness, not compliance driven checkbox, and have it integrated into the culture. Pen test by crowd sourcing—test with logging COSSP http://www.cossp.org/ - Comprehensive Open Source Security Project What Journalists Want: The Investigative Reporters' Perspective on Hacking Dave Maas, San Diego CityBeat Jason Leopold, Truthout.org The difference between hackers and investigative journalists: For hackers, the motivation varies, but method is same, technological specialties. For investigative journalists, it's about one thing—The Story, and they need broad info-gathering skills. J-School in 60 Seconds: Generic formula: Person or issue of pubic interest, new info, or angle. Generic criteria: proximity, prominence, timeliness, human interest, oddity, or consequence. Media awareness of hackers and trends: journalists becoming extremely aware of hackers with congressional debates (privacy, data breaches), demand for data-mining Journalists, use of coding and web development for Journalists, and Journalists busted for hacking (Murdock). Info gathering by investigative journalists include Public records laws. Federal Freedom of Information Act (FOIA) is good, but slow. California Public Records Act is a lot stronger. FOIA takes forever because of foot-dragging—it helps to be specific. Often need to sue (especially FBI). CPRA is faster, and requests can be vague. Dumps and leaks (a la Wikileaks) Journalists want: leads, protecting ourselves, our sources, and adapting tools for news gathering (Google hacking). Anonomity is important to whistleblowers. They want no digital footprint left behind (e.g., email, web log). They don't trust encryption, want to feel safe and secure. Whistleblower laws are very weak—there's no upside for whistleblowers—they have to be very passionate to do it. Accessibility and Security or: How I Learned to Stop Worrying and Love the Halting Problem Anna Shubina, Dartmouth College Anna talked about how accessibility and security are related. Accessibility of digital content (not real world accessibility). mostly refers to blind users and screenreaders, for our purpose. Accessibility is about parsing documents, as are many security issues. "Rich" executable content causes accessibility to fail, and often causes security to fail. For example MS Word has executable format—it's not a document exchange format—more dangerous than PDF or HTML. Accessibility is often the first and maybe only sanity check with parsing. They have no choice because someone may want to read what you write. Google, for example, is very particular about web browser you use and are bad at supporting other browsers. Uses JavaScript instead of links, often requiring mouseover to display content. PDF is a security nightmare. Executible format, embedded flash, JavaScript, etc. 15 million lines of code. Google Chrome doesn't handle PDF correctly, causing several security bugs. PDF has an accessibility checker and PDF tagging, to help with accessibility. But no PDF checker checks for incorrect tags, untagged content, or validates lists or tables. None check executable content at all. The "Halting Problem" is: can one decide whether a program will ever stop? The answer, in general, is no (Rice's theorem). The same holds true for accessibility checkers. Language-theoretic Security says complicated data formats are hard to parse and cannot be solved due to the Halting Problem. W3C Web Accessibility Guidelines: "Perceivable, Operable, Understandable, Robust" Not much help though, except for "Robust", but here's some gems: * all information should be parsable (paraphrasing) * if not parsable, cannot be converted to alternate formats * maximize compatibility in new document formats Executible webpages are bad for security and accessibility. They say it's for a better web experience. But is it necessary to stuff web pages with JavaScript for a better experience? A good example is The Drudge Report—it has hand-written HTML with no JavaScript, yet drives a lot of web traffic due to good content. A bad example is Google News—hidden scrollbars, guessing user input. Solutions: Accessibility and security problems come from same source Expose "better user experience" myth Keep your corner of Internet parsable Remember "Halting Problem"—recognize false solutions (checking and verifying tools) Stop Patching, for Stronger PCI Compliance Adam Brand, protiviti @adamrbrand, http://www.picfun.com/ Adam talked about PCI compliance for retail sales. Take an example: for PCI compliance, 50% of Brian's time (a IT guy), 960 hours/year was spent patching POSs in 850 restaurants. Often applying some patches make no sense (like fixing a browser vulnerability on a server). "Scanner worship" is overuse of vulnerability scanners—it gives a warm and fuzzy and it's simple (red or green results—fix reds). Scanners give a false sense of security. In reality, breeches from missing patches are uncommon—more common problems are: default passwords, cleartext authentication, misconfiguration (firewall ports open). Patching Myths: Myth 1: install within 30 days of patch release (but PCI §6.1 allows a "risk-based approach" instead). Myth 2: vendor decides what's critical (also PCI §6.1). But §6.2 requires user ranking of vulnerabilities instead. Myth 3: scan and rescan until it passes. But PCI §11.2.1b says this applies only to high-risk vulnerabilities. Adam says good recommendations come from NIST 800-40. Instead use sane patching and focus on what's really important. From NIST 800-40: Proactive: Use a proactive vulnerability management process: use change control, configuration management, monitor file integrity. Monitor: start with NVD and other vulnerability alerts, not scanner results. Evaluate: public-facing system? workstation? internal server? (risk rank) Decide:on action and timeline Test: pre-test patches (stability, functionality, rollback) for change control Install: notify, change control, tickets McAfee Secure & Trustmarks — a Hacker's Best Friend Jay James, Shane MacDougall, Tactical Intelligence Inc., Canada "McAfee Secure Trustmark" is a website seal marketed by McAfee. A website gets this badge if they pass their remote scanning. The problem is a removal of trustmarks act as flags that you're vulnerable. Easy to view status change by viewing McAfee list on website or on Google. "Secure TrustGuard" is similar to McAfee. Jay and Shane wrote Perl scripts to gather sites from McAfee and search engines. If their certification image changes to a 1x1 pixel image, then they are longer certified. Their scripts take deltas of scans to see what changed daily. The bottom line is change in TrustGuard status is a flag for hackers to attack your site. Entire idea of seals is silly—you're raising a flag saying if you're vulnerable.

    Read the article

  • verify cert with certutil.exe

    - by Michal
    Hi, I have stupid problem, what is correct syntax on verify certificate in certificate store with certutil.exe. I have client certificate in cerstore. I try this: certutil.exe -verify CertCommonName but in finish with this error : DecodeFile returned The system cannot find the file specified. 0x80070002 (WIN32 : 2) LoadCert(Cert) returned The system cannot find the file specified. 0x80070002 (W IN32: 2) CertUtil: -verify command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. When I ping certutil.exe -ping it connect to pc.

    Read the article

  • GRE keepalive with Linux and RouterOS

    - by eri
    I have a Linux host and couple of routerboadrs. I created a GRE tunnel, but Linux does not answer keepalive packages. Then router mark gre connection as unreachable, so I cant send to Linux host from router subnet. If linux sends something into tunnel (ping, etc.) - RouterOS mark connection as reacheble. Second and next packages routed nicely until one minute idle (no traffic). Tunnel in linux a make in this way: remote=x.x.x.x dev=gre21 network=10.21.0.0/16 ip tunnel add ${dev} mode gre remote ${remote} ttl 255 ip addr add 172.16.1.1/24 peer 172.16.1.21 dev ${dev} ip link set ${dev} up ip route add ${network} dev ${dev} And ip l: 14: gre21: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN link/gre 0.0.0.0 peer 109.60.170.15 How to set state "running"? How to keep alive tunnel? Ping in cron?

    Read the article

  • pfsense peer-to-peer OpenVPN not connecting

    - by John P
    I'm trying to setup a peer-to-peer OpenVPN between two pfsense servers running 2.0.1-RELEASE, but the client keeps getting the connection dropped, with a status of "reconnecting; ping-restart" and nothing appears to be routing between them. Both these firewalls are also doing PPTP VPNs that are working correctly. FW01 ("server") ======================= LAN: 10.1.1.2/24 WAN: xx.xx.126.34/27 ServerMode: Peer to Peer (Shared Key) Protocol: UDP DeviceMode: tun Interface: WAN Port 1194 Tunnel: 10.0.8.1/30 Local Network: 10.1.1.0/24 Remote Network: 192.168.1.0/24 Firewall Rule in OpenVPN tab: UDP * * * * * none FW03 (client) LAN: 192.168.1.2/24 WAN: xx.xx.9.66/27 ServerMode: Peer to Peer (Shared Key) Protocol: UDP DeviceMode: tun Interface: WAN Server Host: xx.xx.126.34 Tunnel: -- also tried 10.1.8.0/24 Remote Network: 10.1.1.0/24 Client Logs: System Log Apr 6 18:00:08 kernel: ... Restarting packages. Apr 6 18:00:13 check_reload_status: Starting packages Apr 6 18:00:19 php: : Restarting/Starting all packages. Apr 6 18:00:56 kernel: ovpnc1: link state changed to DOWN Apr 6 18:00:56 check_reload_status: Reloading filter Apr 6 18:00:57 check_reload_status: Reloading filter Apr 6 18:00:57 kernel: ovpnc1: link state changed to UP Apr 6 18:00:57 check_reload_status: rc.newwanip starting ovpnc1 Apr 6 18:00:57 check_reload_status: Syncing firewall Apr 6 18:01:02 php: : rc.newwanip: Informational is starting ovpnc1. Apr 6 18:01:02 php: : rc.newwanip: on (IP address: ) (interface: ) (real interface: ovpnc1). Apr 6 18:01:02 php: : rc.newwanip: Failed to update IP, restarting... Apr 6 18:01:02 php: : send_event: sent interface reconfigure got ERROR: incomplete command. all reload reconfigure restart newip linkup sync Client OpenVPN log Apr 6 18:39:14 openvpn[12177]: Inactivity timeout (--ping-restart), restarting Apr 6 18:39:14 openvpn[12177]: SIGUSR1[soft,ping-restart] received, process restarting Apr 6 18:39:16 openvpn[12177]: NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Apr 6 18:39:16 openvpn[12177]: Re-using pre-shared static key Apr 6 18:39:16 openvpn[12177]: Preserving previous TUN/TAP instance: ovpnc1 Apr 6 18:39:16 openvpn[12177]: UDPv4 link local (bound): [AF_INET]64.94.9.66 Apr 6 18:39:16 openvpn[12177]: UDPv4 link remote: [AF_INET]64.74.126.34:1194 Server OpenVPN log Apr 6 14:40:36 openvpn[22117]: UDPv4 link remote: [undef] Apr 6 14:40:36 openvpn[22117]: UDPv4 link local (bound): [AF_INET]xx.xx.126.34:1194 Apr 6 14:40:36 openvpn[21006]: /usr/local/sbin/ovpn-linkup ovpns1 1500 1557 10.1.8.1 10.1.8.2 init Apr 6 14:40:36 openvpn[21006]: /sbin/ifconfig ovpns1 10.1.8.1 10.1.8.2 mtu 1500 netmask 255.255.255.255 up Apr 6 14:40:36 openvpn[21006]: do_ifconfig, tt-ipv6=0, tt-did_ifconfig_ipv6_setup=0 Apr 6 14:40:36 openvpn[21006]: TUN/TAP device /dev/tun1 opened Apr 6 14:40:36 openvpn[21006]: Control Channel Authentication: using '/var/etc/openvpn/server1.tls-auth' as a OpenVPN static key file Apr 6 14:40:36 openvpn[21006]: NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Apr 6 14:40:36 openvpn[21006]: OpenVPN 2.2.0 amd64-portbld-freebsd8.1 [SSL] [LZO2] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Aug 11 2011 Apr 6 14:40:36 openvpn[17171]: SIGTERM[hard,] received, process exiting Apr 6 14:40:36 openvpn[17171]: /usr/local/sbin/ovpn-linkdown ovpns1 1500 1557 10.1.8.1 10.1.8.2 init Apr 6 14:40:36 openvpn[17171]: ERROR: FreeBSD route delete command failed: external program exited with error status: 1 Apr 6 14:40:36 openvpn[17171]: event_wait : Interrupted system call (code=4) Apr 6 14:06:32 openvpn[17171]: Initialization Sequence Completed Apr 6 14:06:32 openvpn[17171]: UDPv4 link remote: [undef] Apr 6 14:06:32 openvpn[17171]: UDPv4 link local (bound): [AF_INET]xx.xx.126.34:1194

    Read the article

  • win xp wifi networking

    - by user3485532
    I have 2 pcs with win xp and a wifi router ( without outgoing internet connection )...my job was to connect them over wifi to share some files. router was properly configured, both computers connected to wifi without problems, but when I tried to network them I could not see them in workgroup...i changed their names and added them to same workgroup but i couldn't connect pc1 to pc2 ( i could ping router from each pc but pinging other computer resulted in ping timeout) ..now i cant figure out why this is not working since I've done this before on more complex networks and it should work but...( maybe I have gremlins hiding somewhere..) edit1: Firewall is down on both machines( I disengaged it in both control panel and in services) and folder sharing and permissions are ok.. edit2: I know about Ad Hoc network ( wlan-to-wlan, without router/switch ) but that's not what I am trying to accomplish here :)

    Read the article

  • What does it mean when ARP shows <incomplete> on eth1

    - by Geoff Dalgas
    We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps.

    Read the article

  • DNS "recursion not available" using a Cisco AnyConnect VPN connection

    - by codeape
    Does anyone have experience with configuring Cisco AnyConnect VPN? We have a problem with client DNS name resolution when connected over VPN. To me, it looks as if the Cisco AnyConnect VPN client intercepts DNS queries from the clients. Can someone confirm that the AnyConnect VPN client in fact does this (intercepts DNS traffic)? Where is this configured on the VPN server? EDIT: Here's how the routing table changes when I connect to the VPN: [~] $ diff -u /tmp/route_normal /tmp/route_vpn --- /tmp/route_normal 2010-01-20 19:23:47.000000000 +0100 +++ /tmp/route_vpn 2010-01-20 19:24:46.000000000 +0100 @@ -1,6 +1,10 @@ Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface +xxx.xxx.xx.xx.i 10.0.0.1 255.255.255.255 UGH 0 0 0 ath0 172.16.53.0 * 255.255.255.0 U 0 0 0 vmnet1 10.0.0.0 * 255.255.255.0 U 0 0 0 ath0 +172.17.20.0 * 255.255.255.0 U 0 0 0 cscotun 0 +192.168.111.0 172.17.20.212 255.255.255.0 UG 0 0 0 cscotun 0 172.16.140.0 * 255.255.255.0 U 0 0 0 vmnet8 +172.16.0.0 172.17.20.212 255.255.0.0 UG 0 0 0 cscotun 0 default 10.0.0.1 0.0.0.0 UG 0 0 0 ath0 EDIT 2: The IT guy has done "something" on the VPN endpoint. Now I get "recursion not available" when doing nslookup. The DNS servers have recursion enabled. So it must be the Cisco VPN DNS interception messing this up. ubuntu@domU-12-31-39-00-ED-14:~$ /opt/cisco/vpn/bin/vpn connect xxx.xxxxxx.xx ... >> Please enter your username and password ... >> notice: Establishing VPN... >> state: Connected >> notice: VPN session established to ... ubuntu@domU-12-31-39-00-ED-14:~$ nslookup www.vg.no ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server Server: 172.16.0.23 Address: 172.16.0.23#53 ** server can't find www.vg.no.compute-1.internal: REFUSED ubuntu@domU-12-31-39-00-ED-14:~$ ping 195.88.55.16 PING 195.88.55.16 (195.88.55.16) 56(84) bytes of data. 64 bytes from 195.88.55.16: icmp_seq=1 ttl=240 time=110 ms 64 bytes from 195.88.55.16: icmp_seq=2 ttl=240 time=111 ms 64 bytes from 195.88.55.16: icmp_seq=3 ttl=240 time=109 ms ^C --- 195.88.55.16 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2017ms rtt min/avg/max/mdev = 109.953/110.379/111.075/0.496 ms

    Read the article

  • PPTP VPN on OS X and iOS failed to connect Facebook and Youtube

    - by bGiraffe
    Thnaks for reading. I setup a VPN server on my Buffalo WHR-HP-G300N router at Macau, and use it for access website over China Firewall when i travel in China. On Android and Windows, everything work fine, however on my Macbook Air and iPad, it is not working. I can access blocked site like badoo.com but not facebook and youtube. If i ping it at terminal, it said "ping: cannot resolve facebook.com: Unknown host". After i read this http://cp.hidemynet.com/knowledgebase.php?action=displayarticle&id=26, i find i can restart my router and reboot my Macbook, and connect to VPN before any request to any blocked site so that i can successfully connect to facebook and youtube. However it works sometime but not always. It is really annoying because i need to work on VPN and my Mac, would anyone can help me to solve it? Rather than restarting my router and my Mac every time. Please HELP!!! regards

    Read the article

  • Unable to access local network when Cisco VPN client is connected

    - by bryanroth
    I'm a developer and don't have much networking expertise, so bear with me. I'm using the Cisco VPN Client 5.0.02.0090 to connect to my work's VPN that way I can RDP into my work computer. Once connected, I can't ping anything on the local network once connected to the VPN thus I am unable to access my work's network. This used to work about two weeks ago but abruptly stopped working today. However, I have the Cisco VPN Client installed on my laptop and I am able to ping and RDP into my work computer from there. Both my desktop and laptop computers are connected to the same router at home. I have tried the following so far: Rebooted my computer Reinstalled VPN client Updated NIC drivers Disabled firewall Opened up ports 500, 4500, and 10000 Any help would be much appreciated. Thanks!

    Read the article

  • mac osx cannot connect to windows 7 machine

    - by Binary X
    I have a Mac OSX (Snow Leopard 10.6.6) setup on a network with several Windows 7 machines. When trying to place a large file on a Windows share the connection to the Windows share gets lost and I am unable to reconnect until I reboot the Mac. I know this is on the Windows side because the Mac can connect and transfer files to Server 2008 and XP without issue. Looking in the log file I see this message SharePointBrowser::handleOpenCallBack returned 12 I have tried restarting the com.apple.netauth.sysagent service but that did not resolve the situation. I can do an nslookup to the Windows 7 machine, but trying to ping the machine by hostname always gives a hostname lookup failure (I can ping via IP address). I cannot connect to the machine via IP adress either. Any help would be appreciated.

    Read the article

  • Wireless clients have no route to ethernet clients in OpenWrt router

    - by superjoe30
    I'm using OpenWrt Kamikaze 8.09 on a Linksys WRT54g v1.1 router. I just flashed it with default settings and got everything working, except my wireless laptop cannot ping my desktop which is wired to the router. What can I do to fix this? (My desktop can ping other desktops wired to the router) My routing table: config 'defaults' option 'syn_flood' '1' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'lan' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'wan' option 'input' 'REJECT' option 'output' 'ACCEPT' option 'forward' 'REJECT' option 'masq' '1' config 'forwarding' option 'src' 'lan' option 'dest' 'wan' option 'mtu_fix' '1' config 'redirect' option 'src' 'wan' option '_name' 'ssh' option 'proto' 'tcp' option 'src_dport' '22' option 'dest_ip' '192.168.1.100' option 'dest_port' '22' config 'redirect' option 'src' 'wan' option '_name' 'http' option 'proto' 'tcp' option 'src_dport' '8888' option 'dest_ip' '192.168.1.100' option 'dest_port' '8888'

    Read the article

  • Linksys Router/Tomato Firmware DNS issues

    - by jasonh
    I've got a WRT54GS that I've loaded the current version of Tomato onto. I entered static DHCP addresses in for the devices on my network, released and renewed the address on my desktop and tried to ping another computer. All I got was The request could not find host blah. Please check the name and try again. Now, I verified that my desktop and the target machine I'm trying to ping have both received their proper static DHCP lease and that their DNS server is the IP address of my router. What am I missing?

    Read the article

  • AWS VPN Tunnel going down without traffic

    - by Asfura
    I managed to setup a site-to-site VPN connection from Amazon VPC to a company's network, and after a lot of configuration it was working fine, but now i realized that the VPN tunnel is DOWN every time there's no traffic going trough for a couple minutes. The only way that i have found to generate traffic is to reach the amazon instance from the company's network and then the tunnel goes up again. I had a cronjob doing ping every minute, but i think it should have a keepalive option somewhere, or at least a log file of the tunnels to find out what's going on. Any ideas to keep the tunnel up and/or bring it up from amazon? The firewall is a Checkpoint R75.20, it only allows one tunnel at a time for the same subnet, so i cant have both tunnels active. Thank you, any questions just ask. EDIT I forgot to add, the ping keepalive was working great (maybe generating a bit of traffic, but nothing to worry about), the connection dropped because i had to restart the instance, and it that little time it dropped me.

    Read the article

  • VPN only connects to its server!

    - by Eddie
    Hi guys; Previously I bought a windows 2003 VPS and enabled routing and remote access so that users can make a vpn connection. I turend the firewall off and everything was working fine. But since 2 days ago whenever I try and connect to vpn it connects to vpn without any problem and I can see the connection status however it only connects to the server I mean what I can do with this vpn is to connect to the server via remote desktop and I can ping only the server's IP, neither I can open any webpages in browsers or ping other IP addresses beside the server one! I've also rebuilt the server and configured it for routing access and vpn connection from the beginning but it doesn't work either. It seems that server fails to route the traffic properly, as i'm sure that the firewall has been turned off I can't figure out what's the reason, any idea what's going on? Thanks in advance

    Read the article

  • DHCP Client Can't Find DHCP Server

    - by leeman24
    I currently have 3 machines: CentOS (router) eth1 - 18.0.168.1 eth2 - 145.165.34.1 Windows Server 2008 (server) 18.0.168.2 DHCP scope - 145.165.34.10 - 145.165.34.20 Windows 7 (client) Supposed to use DHCP I can't get my Windows 7 client to get an address from the Windows Server 2008 DHCP server. Every network interface can ping each other (ex. 18.0.168.2 can ping 18.0.168.1 & 145.165.34.1 and the other way around). My Linux machine acting as the router has default IP tables. Other than this command which may or may not be right: iptables -I INPUT -p udp -d 18.0.168.2 --dport 67:68 -j ACCEPT I have also tried it after I flushed the IP tables. I was looking at the dhcrelay command but it seems CentOS doesn't have it and I am not even sure how to use it.

    Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >