Search Results

Search found 10492 results on 420 pages for 'online backups'.

Page 343/420 | < Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >

  • Is "DSLAM congestion" a legitimate reason for slow DSL?

    - by Jay Bazuzi
    My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

    Read the article

  • nginx proxy_pass POST 404 errors

    - by Scott
    I have nginx proxying to an app server, with the following configuration: location /app/ { # send to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } Any request for /app goes to :9001, whereas the default site is hosted on :9000. GET requests work fine. But whenever I submit a POST request to /app/any/post/url it results in a 404 error. Hitting the url directly in the browser via GET /app/any/post/url hits the app server as expected. I found online other people with similar problems and added proxy_set_header Host $http_host; but this hasn't resolved my issue. Any insights are appreciated. Thanks. Full config below: server { listen 9000; ## listen for ipv4; this line is default and implied #listen [::]:80 default_server ipv6only=on; ## listen for ipv6 root /home/scott/src/ph-dox/html; # root ../html; TODO: how to do relative paths? index index.html index.htm; # Make site accessible from http://localhost/ server_name localhost; location / { # First attempt to serve request as file, then # as directory, then fall back to displaying a 404. try_files $uri $uri/ /index.html; # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } location /app/ { # rewrite here sends to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; allow ::1; deny all; } }

    Read the article

  • Compile php 5.3 ldap extension

    - by toups
    So trying to follow the very un-descriptive guide at my webhost for compiling a new php extension: **Compiling PHP 5.3 extensions You can also compile and load your own extensions. Here's how:** 1. Download and unpack the extension (from PECL, for instance). 2. If the extension is already compiled (most binary PHP loaders will be, for instance), skip to step 6. 3. /usr/local/php53/bin/phpize 4. ./configure --with-php-config=/usr/local/php53/bin/php-config 5. make 6. Copy the module to your .php/5.3/ directory. 7. Assuming your user is called "username" and your module is named "mymodule.so", add the following to your .php/5.3/phprc: extension = /home/username/.php/5.3/mymodule.so Downloaded Openldap stable release online, uploaded the unpacked gzip via ftp to my server, did step 3, 4, 5. Now on step 6 is says "copy the module...". My question is where is the module for me to copy? Sorry if it's obvious and I'm not seeing it; first time compiling a php extension :O

    Read the article

  • See former key sequences in vim

    - by Vasiliy Sharapov
    Sometimes I share screen shots and clips of vim usage with others. It would be nice to expand on the part of the status bar highlighted in this picture: I would like some way to make previous key sequences visible as well, such as: y2w jj f[ p 2d - You can see the key sequences leading up to the current one. I'll elaborate on my wish list at the bottom. Is something like this is available as a plugin or vim script? The sheer number of scripts available on vim online makes this hard to find by keyword. Some features I would hope for (but seem improbable): Delimit key sequences with a non-keyboard character instead of space, and a different one for the current command, so y2w jj f[ p 2d might become y2w¦jj¦f[¦p » 2d Replace keys that have a letter alternative with the alternative, such as the right arrow key - ^[[C with the equivalent l. Edit: To clarify, the right arrow key is a valid key in vim, but has no character to represent it, the l key preforms the same function and could/should substitute it. Have previous keystrokes run all the way to the beginning of the line (instead of just one or two), and just have vim's command prompt overwrite it when necessary. Replace some keystrokes with a more elegant alternative, for example hhhhh with 5h or more impressively d2f) with d% (in the appropriate situation).

    Read the article

  • Test whether svn REPO changes are reflected in Working Copy

    - by user492160
    Requirement Changes will be made to the REPO directory and this should get updated to wc(working copy) as opposed to the normal way of WC REPO. Senario: My svn repo- /var/www/svn/drupal My checkout-dir/working-copy- /var/www/html/drupalsite So I've done: edited post-commit hook to contain: "/usr/bin/svn update /var/www/html/drupalsite" I won't make any change to svn WC. I'll make changes to svn REPO- /var/www/svn/drupal. After changes are made to svn repo, run "svn commit /var/www/html/drupalsite". This will trigger the post-commit hook. This inturn will run "svn update /var/www/svn/drupal" and thus my WC will get updated with the changes of REPO. Query a. Would the above steps 1-3 help achieve my 'Requirement'? b. I'd need advise on how to test if the above setup works successfully or not. I'm at loss about the success of steps 1-3 the reason why query(a) is present. This is a bit more of a concern for me. NB: I'm new to subversion. Whatever I've configured till now have been done by reading articles online. Reason for query (b) is because I'm not into development. It seems to be a php drupal website and I happen to be setting it up. So I'm not aware as to how to make a "PROPER" change in REPO so that it gets reflected in WC. If reflected, my configs are right and the team can start on development. I manually put a random file/folder into REPO dir for seeing a change in WC and ran steps 1-3 but was of no avail and later on learned that it was NOT the way to make a change to a REPO. Pleas advise. Thanks

    Read the article

  • RAID 5 Install on Ubuntu Server 12.04 [closed]

    - by tarabyte
    Environment: Ubuntu Server 12.04, installing from bootable flash drive Error: No root file system is defined. Please correct this from the partitioning menu. I'm trying to set up a personal file server with software RAID 5. I just got three hard drives for this, but haven't found any solid documentation. I'm unsure what the basic way to partition my hard drives is. Can someone upload a screenshot of their "partition disks" screen so that I can compare with mine (attached)? Should I set the bootable flag? Do I need a /home partition? A /boot partition? Should I "Use [my partition] as: Ext4 journaling file system"? Or make that field "physical volume for RAID"? I am an engineer, but I have only a cursory knowledge of all-things-linux. If you know of any good learning resources I'd be happy to hear about those too (that way I don't have to blindly follow deprecated tutorials online). well, image would be here but i don't have a high enough reputation yet (please vote up :)) Thank you, References I've looked into: https://help.ubuntu.com/community/Installation/SoftwareRAID https://help.ubuntu.com/12.04/serverguide/advanced-installation.html http://forevergeeks.com/setup-ubuntu-server-with-raid-5/

    Read the article

  • Unable to Access Localhost after starting Xampp

    - by user7370
    OS: Windows XP Professional, SP 2. Few days back i had xampplite 1.7.1 installed and was able to access localhost and phpmyadmin through browser...... Today it suddenly stopped working. In firefox after i type http://localhost/ nothing happens, just blank white screen. I removed all the files in xampplite folders and re-installed ver 1.7.1 again, it's of no use. Then i installed xampplite 1.7.2 (latest), which i had downloaded from xampp website, again it's of no use. Apache and MySql are running though. I tried using locally installing wordpress, as i have a theme ready and want to convert that design to wordpress, test it and start using it online. Running 'Port-check' on xampp control panel showed this -- RESULT ------ Service -- -- Port -- -- Status -- --------------------------------------------------- Apache (HTTP) -- 80 -- C:\xampplite\apache\bin\httpd.exe Apache (WebDAV) -- 81 -- free Apache (HTTPS) -- 443 -- C:\xampplite\apache\bin\httpd.exe MySQL -- 3306 -- C:\xampplite\mysql\bin\mysqld.exe FileZilla (FTP) -- 21 -- free FileZilla (Admin) -- 14147 -- free Mercury (SMTP) -- 25 -- free Mercury (POP3) -- 110 -- free Mercury (IMAP) -- 143 -- free Mercury (HTTP) -- 2224 -- free Mercury (Finger) -- 79 -- free Mercury (PH) -- 105 -- free Mercury (PopPass) -- 106 -- free Tomcat (AJP/1.3) -- 8009 -- free Tomcat (HTTP) -- 8080 -- free --------------------------------------------- I also Have skype installed but it's not using 'Port 80' (as i have read, this was the issue, but checked under skype option the port is 65013). And when i run file:///C:/xampp/htdocs/index.php - it shows "Something is wrong with the XAMPP installation :-( " Please help with this problem. thanks Sharath kumar

    Read the article

  • WRTU54G-TM router with 3rd party firmware; Can custom firmware include stock binary portions?

    - by dlamblin
    I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly? Update I have found someone working on 3rd party WRTU54G-TM firmware. I am still interested in my second part of the questions, that is can't the stock firmware images be pulled apart and have the close-source, if any, binary kernel modules moved into another more flexible custom firmware?

    Read the article

  • VNC as a Support Tool Over the Internet

    - by dosboy
    I'd like to set up an environment where I can use VNC to remotely support my clients over the internet. No VPNs involved. I've used the UltraVNC repeater in the past, but the problem is that it requires a dedicated Windows server. What I'd like to do is as follows: VNC Client (me) - NAT - Internet - NAT - VNC Server (the person I'm offering support to) I'd basically like the same functionality that the UltraVNC repeater offers, but the only internet environment I have to host something on is a Linux shared server (standard hosting - PHP, Apache, etc.). Requirements: Multiple platform support for both Client and Server - specifically Mac and Windows Allows for connection with multiple NATs involved (Client and Server side) Will allow me to use my existing hosting environment for any repeater that might be involved I believe the way this would work is that the Server (the person I'm offering support to) when online would connect to a listener on the internet. When they needed support I would connect my Client to the same listener, see them connected, and use the listener (man-in-the-middle) to piggyback my Client to connect to their Server. I'm open to using any software (not limiting myself to VNC) but would prefer a FOSS solution (which is why I'm leaning towards VNC). Any advice would be greatly appreciated.

    Read the article

  • Windows RDP cannot connect to x64 server from XP SP3+

    - by Tom
    Hi all, I have a strange problem that I can't seem to find the answer to anywhere online. The issue has to do with using Windows RDP to connect to our servers. Here is what works: -XP/Vista client (any SPs) connecting to 32-bit Server 2003 machine -XP (SP2 and lower) client conecting to 64-bit Server 2003 machine Here is what does not work: - XP SP3+/Vista client connecting to 64-bit Server 2003 machine It appears that the issue is that XP SP3 and Vista clients cannot connect to x64 Server 2003 boxes. After entering the username/password, we get an error message saying the below, and the connection drops: To log on to this remote computer, you must have Terminal Server User Access persmissions on this computer. By default, members of the Remote Desktop Users group have these permissions. If you are not a member of the Remote Desktop Users group or another group that has these persmissions, or if the Remote Desktop User group does not have these permissions, you must be granted these permissions manually. The issue is that the user is a member of the Administrators group, which has permission. Also, logging in using the same username, but from an XP SP2 machine, has no problems at all. I hope I explained this well enough, and any help/insight that can be given would be greatly appreciated. Thanks, Tom

    Read the article

  • Setting up HTTPS across multiple servers

    - by JohnyD
    I'm looking to offer our online services over https and I'm having a couple of problems understanding how to accomplish this. To access our services you must pass through our ISA firewall to a Win2000 server running IIS6. About half our services are located here and the other half take you to a Win2003 server also running IIS6. So, in order to achieve this must each server have the proper certificate installed? ISA, IIS6_1 and IIS6_2? Is there a separate configuration that must be made to our ISA firewall? The other problem is with the CA and knowing how many certificates I need. It's important to note that the domain name for our services on IIS6_1 is www.domainname.com but the domain name on IIS6_2 is services.domainname.com. I believe that this will require me to purchase more than one certificate. It looks as though we will be going with Thawte's SSL123 as it's a good name and it's fast to get. Will I need to purchase 2 certificates (one for www that will be installed on our ISA firewall as well as IIS6_1, and one for services.domainname.com on IIS6_2)? Or will I need to purchase 3, the extra one being used on our firewall server? Another side question is about SAN's (subject alternative names). Is this basically adding sub-domains to your cert? So I could purchase one cert with 1 SAN for my www and services.? Thanks a lot for your help! Please let me know if I can provide any further information.

    Read the article

  • Windows RDP cannot connect to x64 server from XP SP3+ [closed]

    - by Tom
    Hi all, I have a strange problem that I can't seem to find the answer to anywhere online. The issue has to do with using Windows RDP to connect to our servers. Here is what works: -XP/Vista client (any SPs) connecting to 32-bit Server 2003 machine -XP (SP2 and lower) client conecting to 64-bit Server 2003 machine Here is what does not work: - XP SP3+/Vista client connecting to 64-bit Server 2003 machine It appears that the issue is that XP SP3 and Vista clients cannot connect to x64 Server 2003 boxes. After entering the username/password, we get an error message saying the below, and the connection drops: To log on to this remote computer, you must have Terminal Server User Access persmissions on this computer. By default, members of the Remote Desktop Users group have these permissions. If you are not a member of the Remote Desktop Users group or another group that has these persmissions, or if the Remote Desktop User group does not have these permissions, you must be granted these permissions manually. The issue is that the user is a member of the Administrators group, which has permission. Also, logging in using the same username, but from an XP SP2 machine, has no problems at all. I hope I explained this well enough, and any help/insight that can be given would be greatly appreciated. Thanks, Tom

    Read the article

  • If spambots are filling out forms on my website, should I mark the mail as spam?

    - by rob
    Apparently spambots have discovered the contact forms my website. I'm considering adding a CAPTCHA, but in the meantime I've been getting dozens of completed website forms in my Gmail account each day. I know I can configure a filter to always allow e-mails from my website to be delivered (i.e., "never send to spam"), but I'm wondering whether there are also larger implications. At first, I was marking the spam forms as spam because I figured it would block the sender's e-mail address from getting through again. But since then, I've given it some more thought. I know many spam filters use Bayesian filters and other techniques to identify spam based on its content. If I mark all these e-mails as spam, will legitimate e-mails from my website be marked as spam? Even if I stop marking the messages as spam, I can see another potential problem. My form is pretty standard (in fact, it's probably very similar to other online forms). If I mark my spambot-submitted website forms as spam, will Gmail begin to mark other people's similar-looking messages as spam?

    Read the article

  • How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

    - by McCoy
    Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

    Read the article

  • Proper 16:9 video size for non-HD 4:3 video (for youtube/vimeo)

    - by Xeoncross
    Since High Definition video came out on all the online sites it has changed the default aspect ratio of the player from 4:3 to 16:9. This means that for people posting SD video you have to resize some of your videos to get them to fit right. For example, NTSC DVD quality (aka 480i/p) is 720x480 pixels (width x height). However, low-end High Definition (720i/p) is 1280x720. Resolution Chart Anyway, now that the video players are built for HD you will find that uploading standard quality videos will result in videos that are "letter boxed" which means they have extra black bars on the top and bottom (or sides). Correct me if I'm wrong, but in order to get a 720x480 video to fit a box that is designed for HD the best practice would be to crop some of it off so that it fits as 720x404 since: 16/9 = 1.78 (1.7777777777778) 720/405 = 1.78 405x1.78 = 720.9 The same would stand for 640x480 (old TV quality) video that would need to be 640x360 correct? I'm asking because I'm not sure about all this and whether this is the proper way to fix these letter-boxing/display problems.

    Read the article

  • How to handle server failure in an n-tier architecture?

    - by andy
    Imagine I have an n-tier architecture in an auto-scaled cloud environment with say: a load balancer in a failover pair reverse proxy tier web app tier db tier Each tier needs to connect to the instances in the tier below. What are the standard ways of connecting tiers to make them resilient to failure of nodes in each tier? i.e. how does each tier get the IP addresses of each node in the tier below? For example if all reverse proxies should route traffic to all web app nodes, how could they be set up so that they don't send traffic to dead web app nodes, and so that when new web app nodes are brought online they can send traffic to it? I could run an agent that would update all the configs to all the nodes, but it seems inefficient. I could put an LB pair between each tier, so the tier above only needs to connect to the load balancers, but how do I handle the problem of the LBs dying? This just seems to shunt the problem of tier A needing to know the IPs of all nodes in tier B, to all nodes in tier A needing to know the IPs of all LBs between tiers A and B. For some applications, they can implement retry logic if they contact a node in the tier below that doesn't respond, but is there any way that some middleware could direct traffic to only live nodes in the following tier? If I was hosting on AWS I could use an ELB between tiers, but I want to know how I could achieve the same functionality myself. I've read (briefly) about heartbeat and keepalived - are these relevant here? What are the virtual IPs they talk about and how are they managed? Are there still single points of failure using them?

    Read the article

  • Embedding a WMV file on the web via URL in a Powerpoint presentation

    - by Dave
    I've got a situation where I want to distribute a Powerpoint presentation to several people. I want to be able to embed several large videos in this presentation by linking to a URL, for the following specific reasons: the videos are highly confidential, and I would like to be able to delete them at some later date, but still allow them to see it in the presentation while it is online. I want to send the presentation via email (so it should be small), and put the links on a server with a faster upload speed Maybe I'd like to change the video at some point without changing the presentation One option that addresses #1 is to hook up a webcam and allow them to see video stream from the office, but our upload rate is too slow for this to be a viable option. I've tried embedding a video and giving Powerpoint the URL. It seems to work initially, because the first frame appears in my slideshow. However, when I play the slideshow, nothing happens. I looked at the network traffic on my computer, and nothing was getting downloaded from the remote server. Any suggestions on how to make this work, or how to at least satisfy the criteria listed above would be great!

    Read the article

  • Backup and Archive Strategy Question

    - by OneNerd
    I am having trouble finding a backup strategy for our code assets that 'just works' without any manual intervention. Goal is to have an off-site backup (a synchronized one) so that when we check-in files, create builds, etc. to the network drive, the entire folder structure is automatically synchronized and backed-up (in real time, or 1x per day) at some off-site location so if our office blows up, we don't lose all of our data. I have looked into some online backup services, but have not yet had any success. Some are quirky/buggy, others limit file size and/or kinds of files (which doesn't work well for developer files). Everything gets checked in and saved to a single server (on a Raid Mirror), so we just need to have a folder on that server backed up/synchronized to some off-site location. So my question is this. What are you using for your off-site backup strategy. What software, system, or service? Is there a be-all/end-all system of backing up your code assets that I just haven't found yet? Thanks

    Read the article

  • USB mouse disconnecting and reconnecting in windows and linux

    - by Kalak
    I have a problem similar to what is described at "Why is my USB mouse disconnecting and reconnecting randomly and often?" except is is happening in both Windows 7 and Linux (Ubuntu 12/04TLS, fully patched), multiple mice, multiple OSs. It stops responding to input for about 3-5 seconds, then starts responding again. It's more frequent and lasts longer when running games (TF2, L4D, Dishonored, Borderlands 2, and more), but happens when just running the OS as well. I was hoping it was the motherboard so I bought a USB 2.0 PCI card to try that, but it's still happening. I've stripped it down to just the keyboard and mouse (different keyboard too just in case the keyboard was the problem), but it's still happening. All the hardware (mice and keyboards) work fine on other computers. I have literally pulled the mouse and keyboard out and plugged them into another computer (laptop) and re-joined the online game and had no problem with the keyboard and mouse combo that just failed on my gaming rig. Please no driver / Windows or Linux only suggestions, as that wouldn't effect both OSs. edit: known good mice I've brought home are now going bad. I suspect the hardware is messed up (voltage?) and has been frying the mice.

    Read the article

  • Mac Security - Which one?

    - by Bob Rivers
    Hi, Recently I had my credit card cloned. A few hours after shopping at an online store (in which I trust and buy since 2006) I received a call from my bank asking if I recognize a $5,000 debt to a store(?!) called Church of Christ... I'm a Mac user (OS X 10.6.3). I always kept my system updated and I have firewall enabled (in my Mac and in my broadband router), but I decided to adopt some kind of protection. I don't want to rise passionate discussions. Real or not, snake oil or not, I need to have back my peace of mind... I read this and this posts. I selected two software that I think that could help me (both have more features other than just an antivirus). Does someone have feedback about Intego's VirusBarrier X6 or Trendmicro's Smart Surfing? Intego solutions seems to be better, but TrendMicro brand/name is stronger in corporate environment, so their solution should be good. Both solutions have 30 day free trial, but I would like to hear something from you. Any other solution that I should look? TIA, Bob

    Read the article

  • Excel file growing huge (>150 MB)

    - by Josh
    There is one particular Excel file that is used by a number of employees at my company. It is edited from both Excel 2003 and 2007, with the "Sharing" feature turned on to allow multiple writers at once. The file has a decent amount of data on several sheets with some basic formatting, and used to be about 6MB, which seems reasonable for its content. But after a few weeks of editing, the file grew to 10, then 20 MB, and eventually skyrocketed to more than 150 MB, even though it still has about the same amount of data as before. It now takes 5-10 minutes to open it, and that much time again to save it. The first time this happened, I copied the content of each sheet into a new, blank workbook, and saved the new workbook; this brought it back down to about 6MB. Now, it has blown up again. The workbook uses the "Data Validation" feature to limit the values in certain columns to the contents of a few named ranges. Copying all the data into a new workbook means re-setting up all the data validation, which is a pain and not something that we want to do every month. As a troubleshooting step, I tried saving the file in "XML Spreadsheet 2003" format, hoping to get some insight into what was being stored. Sure enough, the file was almost a gig, and almost all of the 10 million lines look like this: <NamedCell ss:Name="Z_21D5114F_E50C_46AC_AA4F_C3FF540C717F_.wvu.FilterData"/> <NamedCell ss:Name="Z_1EE2BA5E_3011_4F9A_8ACD_E58835250FC4_.wvu.FilterData"/> <NamedCell ss:Name="Z_1E3BDCEA_6A72_4ECC_BF4F_7B03CC66181E_.wvu.FilterData"/> I've seen a few VBScripts online to manage and enumerate named cells that are hidden in Excel's built-in interface, though I wonder how they'd handle my 10 million named cells. What I really need, though, is an understanding of why this keeps happening. What actions in excel could be causing this?

    Read the article

  • Software to clean up photos of whiteboards and documents?

    - by Norman Ramsey
    I take a lot of photos of whiteboards, blackboards, and so on for teaching purposes (examples online through May 2010). I'm interested in cleaning them up for archival purposes, preferably using Linux. Commercial products ClearBoard and PhotoNote are priced a little aggressively for my purposes, plus my students would like to have this capability too. Does anyone know of any good, open source software for Converting photographs to images with just a few colors? Eliminating perspective distortion? Removing unwanted junk from around the edges of an image? or anything like that? I'm imagining that I start out with a picture of my whiteboard using red and black markers, and I end up with a three-color image using just white, red, and black. Or I photograph a laser-printed document and end up with a clean black-and-white image. I have tried standard tools that reduce the number of colors in an image, and they do a terrible job—probably because they are trying to reproduce the uneven illumination of the original image. Command-line Linux tools would be ideal.

    Read the article

  • Intermittent CNAME forwarding

    - by Godric Seer
    I host a personal website on an old desktop that is LAMP based. Since I have a dynamic IP, I use no-ip to make sure I have a working domain name at all times. I also have a domain I have bought on GoDaddy where I have a CNAME record forwarding the www subdomain to my no-ip domain. At all times, I can connect to my website through the no-ip domain without issue. For the past several weeks, I never had an issue using the GoDaddy domain to connect (ssh or https). As of today, however, the GoDaddy domain only works for about 10 minutes at a time. I get server not found errors most of the time. Also, if I happen to be using the GoDaddy domain for an ssh connection, the connection will freeze. I have attempted to run tests using a couple of online DNS check websites, but have not gotten any errors at any time. I also contacted GoDaddy support but they had no issues connecting to the website, and therefore did not see any issues. I would like advice on how I could debug/resolve this issue. Since the problem appeared without me changing anything on my end, I hope it will resolve itself, but knowing the cause in case it happens again would be preferable. EDIT: I changed the configuration in GoDaddy to create an A (Host) that points at my current IP. This works fine, so I can access the site through the GoDaddy domain without the preceding www. I am currently waiting for a new CNAME record to propagate that points the www subdomain at the main host, rather than my no-ip domain.

    Read the article

  • Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

    - by D.S.
    I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

    Read the article

  • Server Restart's and Respective Orders

    - by TheD
    EDIT:Not meaning to be disrespectful to any of the answers, but, the main question was whether rebooting a DC at the beginning of a cycle, then all the other servers, or rebooting it at the end once all the others are back online - is there a reason for doing it either way? I'm still not sure based on current responses. This will most likely seem like a fairly, maybe even stupid, question, but it's something I have been wondering about. As part of a regular process for clients servers are restarted remotely after patches and every client tends to have a similar order - but there always seems to be a small debate when it comes down to when do you reboot your DC. For example, 4 servers, 1 DC, 1xExchange, 1xBESX and 1xRandom, lets say it has some CRM software installed, is it best to reboot the DC first, then Exchange, then BESX and so on - or reboot all the servers, then reboot the DC last? - Perhaps it doesn't matter at all and it's just a case of how you have always done it. Would it change in a Hyper-V environment for example, with a physical DC, 1 VHost with all your servers virtualised on that Host? Rebooting the VHost and Virtual Machines first, then the DC at the end, or vice versa? Thanks!

    Read the article

< Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >