Search Results

Search found 10466 results on 419 pages for 'restart explorer'.

Page 347/419 | < Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >

• apache2 + mod_fastcgi + suexec + php5.2 = unstable on high load

  I am hosting several (~30) different sites on one server with apache2+fastcgi+suexec+php5. Sites have different loads and different execution times of their scripts (some of them process request for 5-7 seconds, some <1sek). Sometimes when single site receives very high load (all php instances of this site are created and used) - whole apache server hangs. Apache (worker mpm) creates new processes up to the upper limit. It looks like it is starting to queue ALL new request for EVERY site, not only the one that has high load and quickly achieves process limits... restart of apache solves the problem... config: FastCgiConfig -singleThreshold 1 -multiThreshold 10 -listen-queue-depth 30 -maxProcesses 80 -maxClassProcesses 12 -idle-timeout 30 -pass-header HTTP_AUTHORIZATION -pass-header If-Modified-Since -pass-header If-None-Match (earlier have default -listen-queue-depth = 100, but it didn't change anything...) Any suggestions? Another question - how is implemented this listen queue? is it one queue for whole apache, or unique queue for every defined php apllication (suexec site)? I would like to achieve something like this: when one site receives high load and its queue is full - server bounces next request, but only for this one site.. Other sites should work properly...

  Read the article

• Squid with mikrotik router

  - by niren

  I tried to connect squid3 in my network to use high anonymity proxy. This is how my network is right now WAN LINK | ------------- ----------------------------- | Mikrotik Box | | Ubuntu Server with squid3 | ------------- ----------------------------- | / | / ---------------------- | Switch ( Cheap one ) | ---------------------- | | | Client1 Client2 Client3 etc. after this setup I changed squid.conf in Ubuntu server as http_port 8080 acl localhost src xxx.xxx.xxx.xxx(Ubuntu server IP) acl to_localhost dst xxx.xxx.xxx.xxx(Mikrotik router gateway) I assume that redirected http from Mikrotik router will be redirect again to Mikrotik router. uncomment access log /var/log/squid3/access.log add visible_hostname myname save squid.conf and restart squid3 server. Then I have added nat rule in Mikrotik router ip/firewall/nat 1. add chain=dstnat src_address=xxx.xxx.xxx.xxx(ununtu server IP) dst-port=80 protocol=tcp action=accept 2. add chain=dstnat src_address=xxx.xxx.xxx.xxx/28(LAN address) dst-port=80 protocol=tcp action=dst-nat to-address=xxx.xxx.xxx.xxx(ununtu server IP) to-port=8080 now I can not able to access internet from client1 system, If I remove these two nat rule then I can access internet. what is wrong I have made?

  Read the article

• Website memory problem

  - by Toktik

  I have CentOS 5 installed on my server. I'm in VPS server. I have site where I have constant online ~150. First look on site looks OK. But when I go through links, sometimes I receive Out of memory PHP error. It looks like this Fatal error: Out of memory (allocated 36962304) (tried to allocate 7680 bytes) in /home/host/public_html/sites/all/modules/cck/modules/fieldgroup/fieldgroup.install on line 100 And always, not allocated memory is very small. In average I have 30% CPU load, 25% RAM load. So I think here is not a physical memory problem. My PHP memory limit was set to 1500MB. My apache error log looks like this [Thu Sep 30 17:48:59 2010] [error] [client 91.204.190.5] Out of memory, referer: http://www.host.com/17402 [Thu Sep 30 17:48:59 2010] [error] [client 91.204.190.5] Premature end of script headers: index.php, referer: http://www.host.com/17402 [Thu Sep 30 17:48:59 2010] [error] [client 91.204.190.5] Out of memory, referer: http://www.host.com/17402 [Thu Sep 30 17:48:59 2010] [error] [client 91.204.190.5] Premature end of script headers: index.php, referer: http://www.host.com/17402 [Thu Sep 30 17:49:00 2010] [error] [client 91.204.190.5] File does not exist: /home/host/public_html/favicon.ico Past I have not met with this on my server and the problem appeared itself. Besides this I'm receiving some server errors on mail. cpsrvd failed @ Fri Sep 24 16:45:20 2010. A restart was attempted automagically. Service Check Method: [tcp connect] Failure Reason: Unable to connect to port 2086 Same for tailwatchd. Support tried, and can't help me...

  Read the article

• How to recover the plesk database?

  - by Kau-Boy

  When I try to launch the Plesk administration page of you server I get the following error: ERROR: PleskMainDBException MySQL query failed: MySQL server has gone away The MySQL Server is working well. Although it seems that the plesk database is somehow corrupt and any action on this database results in a restart of the mysql process, so even queries to other databases on the same MySQL server will be lost. If I try to connect to the plesk database using phpMyAdmin, I can only see the number of tables, the database had originally. But I am not able to open the tables listing. As soon as I try it, the mysql process crashes again. Trying to connect to the database using ssh works. I can even run a SELECT statement against any table an get a result. I don't know if it is an plesk error or an error of the psa database or even the MySQL server. Can you give me any tips on how to recover the plesk system. Should I try to repair the Plesk installation before. And if so, how can I do it and will all my settings get lost doing it? EDIT: Trying to dump the database, I get the following error: mysqldump: Got error: 2013: Lost connection to MySQL server during query when using LOCK TABLES

  Read the article

• Coffee spilled and went inside CPU...computer not starting

  - by Harpreet

  Today coffee got spilled over my table, and some of it (very less) reached the CPU placed under the table. I think little bit of it got inside the CPU through the front face of the CPU. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• Server nearly unusable when doing disk writes

  - by Wikser

  My question closely relates to my last question here on serverfault. I was copying about 5GB from a 10 year old desktop computer to the server. The copy was done in Windows Explorer. In this situation I would assume the server to be bored by the dataflow. But as usual with this server, it really slowed down. At least I could work with the remote session, even there was some serious latency. The copy took its time (20min?). In this time I went to a colleague and he tried to log in in the same server via remote desktop (for some other reason). It took about a minute to get to the login screen, a minute to open the control panel, a minute to open the performance monitor, ... Icons were loading maybe one per second. We saw the following (from memory): CPU: 2% Avg. Queue Length: 50 Pages/sec: 115 (?) There was no other considerable activity on the server. The server seldom serves some ASP.NET pages, which became also very slow in this time. The relevant configuration is as follows: Windows 2003 SEAGATE ST3500631NS (7200 rpm, 500 GB) LSI MegaRAID based RAID 5 4 disks, 1 hot spare Write Through No read-ahead Direct Cache Mode Harddisk-Cache-Mode: off Is this normal behaviour for such a configuration? What measurements could give further clues? Is it reasonable to reduce the priority of such copy I/O and favour other processes like the remote desktop? How would you do that? Many thanks!

  Read the article

• Destroyed user account on OS X with dscl; how to restore? [migrated]

  - by Sam Ritchie

  I was trying to create a new user on my OS X Lion machine, and somehow managed to destroy my own user's account. Here are the steps I took; hopefully someone here can recognize what I did, and maybe identify some way around this. First, I ran these commands: sudo dscl localhost -create /Local/Default/Users/elasticsearch sudo dscl localhost -create /Local/Default/Users/elasticsearch /bin/bash # mistake! sudo dscl localhost -create /Local/Default/Users/elasticsearch UserShell /bin/bash sudo dscl localhost -create /Local/Default/Users/elasticsearch RealName "Elastic Search" sudo dscl localhost -create /Local/Default/Users/elasticsearch UniqueID 503 # MY uniqueID sudo dscl localhost -create /Local/Default/Users/elasticsearch PrimaryGroupID 1000 sudo dscl localhost -create /Local/Default/Users/elasticsearch NFSHomeDirectory /Local/Users/elasticsearch The big mistake I made here was using "503", which was my user's UniqueID. Immediately my shell username changed to "elasticsearch". I fiddled around, tried to change the current user with sudo su -u sritchie, but this didn't work. On restart, only the "Elastic Search" user was available. I logged into the Lion Recovery partition and reset the root password. After logging in as root and checking on the terminal, I made the remarkable discovery that my home folder was totally empty. I deleted the elasticsearch user, but it made no difference. I don't see anything in Deleted Users either. The odd thing is that when I log in now as myself (sritchie) I can see desktop icons with previews. I can even open a few text files from the Downloads folder if I use the dock alias to Downloads. Could this data be hiding somewhere? Any help would be REALLY appreciated! Thanks, Sam

  Read the article

• NTFS partition size not recognized after disaster recovery clone

  - by djechelon

  I'm in the middle of a disaster recovery of a 250GB hard disk that was "clicking". Obviously I didn't have a backup copy. I managed to salvage all the files thanks to GParted Live that was able to read the disk without a single "click" sound. So I cloned the partition to a new drive sized 500GB. Unfortunately, GParted process went to some kind of infinite loop, disks stopped I/O and after a couple of hours I interrupted the clone process I started. Now the problem is: when cloning the partition I also chose to expand 250GB to the whole 500GB of the target disk. Windows sees the partition sized 500GB in computer management, but Windows Explorer only sees 250. chkdsk e: /f says the filesystem is OK. How can I repair the file system and let Windows see the full 500GB of the new partition? An alternate idea is to deep-copy the files from the backup disk to a newly formatted disk. This should definitely fix. Any other ideas?

  Read the article

• Broken filesystem on Windows XP / 7 virtual machine

  - by Pekka

  I created a virtual machine with Windows XP as the guest system in Microsoft's Virtual PC that ships along with Windows 7. I then installed Virtualbox and began running the MS machine in it. It worked fine. Then, I accidentally started the machine in Microsoft's Virtual PC again. The screen stayed blank, so after a while, realizing my mistake, I closed the Machine. Since then, the VM won't start any more, claiming massive file system problems. Starting Windows in normal mode results in a SOMETHING_FILESYSTEM blue screen; I can start in protected mode and run a checkdisk. That will fix something on every run, but every time I restart, it will start again. I tried re-booting the VM with the Windows CD and doing a repair install. I didn't watch whether that worked out, but I'm caught in the reset / check disk / reset cycle again. Is there anything VM specific that can still be done? On a physical machine, I would say reformat. Is there any way to get hold of the data on the virtual machine through either Virtual PC or Virtualbox? It was an experimental machine, but I had started entering some data on it that would be nice to recover.

  Read the article

• Optimize apache for 10K+ wordpress views a day on 2GB RAM E6500 CPU

  - by Broke artist

  I have a dedicated server with apache/php on ubuntu serving my Wordpress blog with about 10K+ pageviews a day. I have W3TC plug in installed with APC. But every now and then server stop responding or goes dead slow and i have to restart apache to get it back. Heres my config what am i doing wrong? ServerRoot "/etc/apache2" LockFile /var/lock/apache2/accept.lock PidFile ${APACHE_PID_FILE} TimeOut 40 KeepAlive on MaxKeepAliveRequests 200 KeepAliveTimeout 2 StartServers 5 MinSpareServers 5 MaxSpareServers 8 ServerLimit 80 MaxClients 80 MaxRequestsPerChild 1000 StartServers 3 MinSpareServers 3 MaxSpareServers 3 ServerLimit 80 MaxClients 80 MaxRequestsPerChild 1000 StartServers 3 MinSpareServers 3 MaxSpareServers 3 ServerLimit 80 MaxClients 80 MaxRequestsPerChild 1000 User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess Order allow,deny Deny from all Satisfy all DefaultType text/plain HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel error Include /etc/apache2/mods-enabled/.load Include /etc/apache2/mods-enabled/.conf Include /etc/apache2/httpd.conf Include /etc/apache2/ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %s %O" common LogFormat "%{Referer}i - %U" referer LogFormat "%{User-agent}i" agent CustomLog /var/log/apache2/other_vhosts_access.log vhost_combined Include /etc/apache2/conf.d/ Include /etc/apache2/sites-enabled/

  Read the article

• OpenVPN (Tunnelblick) Suddenly Dropping Constantly

  - by Jeremy Privett

  I've been using Tunnelblick on my Mac for OpenVPN for about a year now. All of a sudden, this morning, it decided that it was going to take a nasty turn for the worse with no explanation. Here are the symptoms I'm seeing: I can connect to the VPN fine, initially. After about 2 - 5 minutes of no interruption, the connection suddenly dies. I can still see the VPN route using netstat -rn, and Tunnelblick believes it's still connected. No VPN traffic can go through and I can't even ping the VPN gateway. Eventually, Tunnelblick will catch on that the connection has died (usually about 5 - 10 minutes later) and shoot itself to restart and then the cycle starts over again. I've tried everything I can think of to figure this one out. I've completely flushed my system by rebooting and removing Tunnelblick and all traces of OpenVPN from my system and re-installing from scratch. No dice, same problem. I'm at my wits end, because I desperately need to get this fixed as the VPN is required for me to be able to do my job. Any ideas you have would be greatly appreciated.

  Read the article

• 1and1 ssh - connection refused

  - by kitensei

  I'm having troubles connecting through SSH to my 1&1 account. When I try to connect with command userXXX@host -p22 -vv I have the following output: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to mySite.com [ip_here] port 22. debug1: connect to address ip_here port 22: Connection refused Moreover, once I try to connect through SSH and it fails, even the HTTP access is dead, I cannot access the website through explorer anymore :/ please help < I'm running ubuntu 11.10 EDIT: don't know if it can help, here's the .htaccess of the 1and1 server Options +Indexes Satisfy any Order Deny,Allow Allow from 212.227.X.X Deny from all RemoveType .html .gif AuthType Basic AuthName "Access to /logs" AuthUserFile /kunden/homepages/43/d376072470/htpasswd Require user "user_here" and sftp.log: Mar 26 09:21:24 193.251.X USER_HERE Connection from 193.251.X port 51809 Mar 26 09:21:30 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:39 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:41 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:45 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:57 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 10:53:36 212.227.X tmp64459736-3228 Connection from 212.227.X port 23275 Mar 26 10:53:36 212.227.X tmp64459736-3228 Accepted password for tmp64459736-3228 from 212.227.X port 23275 ssh2 Mar 26 11:53:37 212.227.X tmp64459736-3228 Connection closed by 212.227.X Mar 26 18:58:17 212.227.X tmp64459736-5363 Connection from 212.227.X port 23353 Mar 26 18:58:17 212.227.X tmp64459736-5363 Accepted password for tmp64459736-5363 from 212.227.X port 23353 ssh2 Mar 26 19:53:36 212.227.X tmp64459736-8525 Connection from 212.227.X port 5166 Mar 26 19:53:36 212.227.X tmp64459736-8525 Accepted password for tmp64459736-8525 from 212.227.X port 5166 ssh2 Mar 26 19:58:17 212.227.X tmp64459736-5363 Connection closed by 212.227.X

  Read the article

• Vanishing Windows Desktop Shortcut Keys

  - by Henry Keiter

  The Situation Like you, I have many applications that I like to open. I've set up keyboard shortcuts for the most common, by placing a link on the desktop and setting its Shortcut Key property: This is all fine and dandy, most of the time. When I want to bring up the GIMP, I press Ctrl+Alt+G and the GIMP launches. Lovely. The Problem Sometimes--perhaps once a month per desktop shortcut--the shortcut key assignment simply vanishes. I press Ctrl+Alt+G and nothing happens, so I go check the shortcut and see that lo and behold: nothing is there. This happens regularly to all my shortcuts (not all at once). It doesn't matter what keys I assign, and there doesn't seem to be any correlation with particular applications being open or anything of that sort. This has happened on every Windows XP machine I've ever used with any regularity. Obviously what makes this issue particularly obnoxious is that it's not easily reproducible. I have searched long and hard for a solution for (or at least acknowledgement of) this problem, to no avail, so hopefully you guys know something that I don't. I did find this question, where the answers are all basically "use a third-party app", but as far as I could tell that was a slightly different issue, related to Explorer being busy. If the solution for this turns out to be the same, fine, but I'd prefer a native fix if at all possible. Note: I've tagged this with Windows in general because I seem to remember it happening on Windows 7 as well as XP, but I rarely notice it because I use the start-menu search in preference to desktop shortcuts.

  Read the article

• Cannot change PostgreSQL port

  - by Jerec TheSith

  I run Postgresql 8.4 as a service on a CentOS 6.2 server. I set port = 21444 and listen_addresses = '*' in /var/lib/pgsql/data/postgresql.conf and I changed 5432 to 21444 in postmaster.opts and restarted postgres, but when I run netstat -lntp postgresql is still running on port 5432 tcp 0 0 0.0.0.0:5432 0.0.0.0:* LISTEN 20276/postmaster When I restart postgresql I get a writting error warning on /proc/self/oom_adj, but the service starts anyway. I read that we could get this error when using virtualized servers, but I don't really know if this has inpact on postgresql listening port. The correct pgsql config file is loaded in /var/lib/pgsql/data : [root@srv02 ~]# ps -ef | grep postgres root 1358 22140 0 09:42 pts/0 00:00:00 grep postgres postgres 9519 1 0 Mar16 ? 00:00:01 /usr/bin/postmaster -p 5432 -D /var/lib/pgsql/data postgres 9573 9519 0 Mar16 ? 00:00:00 postgres: logger process postgres 9575 9519 0 Mar16 ? 00:00:05 postgres: writer process postgres 9576 9519 0 Mar16 ? 00:00:03 postgres: wal writer process postgres 9577 9519 0 Mar16 ? 00:00:01 postgres: autovacuum launcher process postgres 9578 9519 0 Mar16 ? 00:00:01 postgres: stats collector process any thought ? thanks, Jerec

  Read the article

• Why does notepad crash on desktop files in the save-as dialog?

  - by deepc

  Here's a puzzling problem - maybe somebody has an idea. Right now I am out of ideas. On Win7 64bit, the following crashes Notepad: On Desktop, right click, select "New | Text Document". This creates "New Text Document.txt". Right click on that file, select "Edit". This opens notepad with the empty file. Select "File | Save as": Notepad crashes and Win7 reports that "Notepad has stopped working". Now, move the file to c:\temp and repeat steps 2 and 3: no crash this time and the save-as dialog appears normally. I can create similar steps for the "open" dialog. Things I have tried: Safe mode - does not work, same problem Create a new user and try again logged in as that user - no crash Name file differently, or create elsewhere and then move to desktop - same problem Use Wordpad instead - same problem Review shell extensions with ShellExView - nothing extraordinary here Stare at the event log entries for each of the crashes. Does not enlighten me. At time of crash look at the process explorer stack view. Hangs at a function "TaskDialog". sfc.exe /scannow repaired some files but the problem persists. This is how the event log entries look like: Log Name: Application Source: Application Error Date: 14.12.2010 00:33:48 Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Description: Faulting application name: NOTEPAD.EXE, version: 6.1.7600.16385, time stamp: 0x4a5bc9b3 Faulting module name: COMCTL32.dll, version: 6.10.7600.16661, time stamp: 0x4c6f6e4b Exception code: 0xc000041d Fault offset: 0x00000000000db770 Faulting process id: 0x198 Faulting application start time: 0x01cb9b1e140ab92a Faulting application path: C:\Windows\system32\NOTEPAD.EXE Faulting module path: C:\Windows\WinSxS\amd64_microsoft.windows.common-controls_6595b64144ccf1df_6.0.7600.16661_none_fa62ad231704eab7\COMCTL32.dll What else should I try, short of dumping my user and starting over with a new profile? Thanks...

  Read the article

• Copying compressed files from Server 2008 R2 network share to XP client via VPN fails

  - by Dejan Janjuševic

  At the first sight the question looks similar to this one. I have experienced an odd behavior while trying to copy a certain file from Windows Server 2008 R2 network share to Windows XP Professional client via VPN. The VPN was set up using RRAS on the server machine. I will try to provide as much informations as possible in order to make the issue more clear. When trying to copy the compressed file sized ~2.5 MB (via Explorer or CMD, doesn't matter), the process stalls after some 20%, producing an error message after few seconds: Cannot copy filename: The specified network name is no longer available. If i start the command ping -t 192.168.2.1 (where the IP address specified belongs to the server) side by side with the copy command, I can clearly see that the ping command times out for few seconds as the copy process stalls. When this happens all network activities are frozen. After a few seconds, the network recovers, ping continues to run normally, however the copy process stands still before it displays the above error message. Copying other files (I tried 4-5 files), of which some are larger and some are smaller, succeeds. Seems to me that I can copy all uncompressed files. As soon as I try to copy an archive, the process freezes. Even a 707 KB large archive can't be copied. I can only reproduce this behavior on 2 machines, both Windows XP Professional, one is w/ SP2 and the other w/ SP3. Other XP clients don't have this problem, neither do Windows 7 clients. If I connect to the server using Remote Desktop Connection without using VPN from either of these 2 machines (using the same user account), I can copy anything I want normally, even these "problematic" files. Does anyone have any clue about what could possibly be going on?

  Read the article

• Shared files folder in Amazon Elastic Beanstalk environment

  - by por

  I'm working on a Drupal application, which is planned to be hosted in Amazon Elastic Beanstalk environment. Basically, Elastic Beanstalk enables the application to scale automatically by starting additional web server instances based on predefined rules. The shared database is running on an Amazon RDS instance, which all instances can access properly. The problem is the shared files folder (sites/default/files). We're using git as SCM, and with it we're able to deploy new versions by executing $ git aws.push. In the background Elastic Beanstalk automatically deletes ($ rm -rf) the current codebase from all servers running in the environment, and deploys the new version. The plan was to use S3 (s3fs) for shared files in the staging environment, and NFS in the production environment. We've managed to set up the environment to the extent where the shared files folder is mounted after a reboot properly. But... The Problem is that, in this setup, the deployment of new versions on running instances fail because $ rm -rf can't remove the mounted directory, and as result, the entire environment goes down and we need restart the environment, which isn't really an elegant solution. Question #1 is that what would be the proper way to manage shared files in this kind of deployment? Are you running such an environment? How did you solve the problem? By looking at Elastic Beanstalk Hostmanager code (Ruby) there seems be a way to hook our functionality (unmount if mounted in pre-deploy and mount in post-deploy) into Hostmanager (/opt/hostmanager/srv/lib/elasticbeanstalk/hostmanager/applications/phpapplication.rb) but the scripts defined in the file (i.e. /tmp/php_post_deploy_app.sh) don't seem to be working. That might be because our Ruby skills are non-existent. Question #2 is that did you manage to hook your functionality in Hostmanager in a portable way (i.e. by not changing the core Hostmanager files)?

  Read the article

• Can I disable this Windows (XP) Security Warning?

  - by FumbleFingers

  I recently reformatted my hard drive and reinstalled Windows XP (I know I'll have to take the plunge and commit to Win8 "real soon, now", but I'm just not quite ready for the upheaval yet! :) I used to use WinRar (and later, when I got fed up with the "nag" messages, 7-Zip), but I haven't installed either of them in my new configuration, so I must be using the built-in XP facility when I open *.zip files. For years, I've been opening downloaded *.zip archives, and using "drag & drop" to copy to a File Explorer window open on the folder where I want the files to end up (usually, My Documents\Downloads). But now I find that when I "drop" the file(s), I get a pop-up Windows Security Warning saying Are you sure you want to copy or move files to this folder? You should only move or copy files from locations that you trust Can anyone explain why I'm getting this message, and is there any (reasonably easy, please! :) way to suppress it? Since I've already put the *.zip file on my computer, it seems a bit late to ask if I trust it. (Thus far, the files in question have always been plain text, so it's not a matter of dodgy programs, etc.) Apologies for the low quality image - I don't have the appropriate tools or knowledge to do any better, and it doesn't help that my "PrtScr" screen capture has included what would have been on my second monitor (TV) if it had been turned on. If you can't read it, trust me - I have copied the text verbatim.

  Read the article

• Windows 7 x64 RTM USB Port Has Power But Won't Recognize Mouse/Keyboard/Anything

  - by ben

  I have an odd error that doesn't seem to fit in with any of the other odd Windows 7 x64 USB errors that have been kicked up on Google. Here we go: Uninstalled Tortoise SVN and clicked restart computer. My machine had been up for around 28 days On reboot my mouse and keyboard failed to work anymore, couldn't log in. Tried every USB port I have on my Dell 390 and the ports on my Dell 19's, nothing worked. They had power but Windows would not respond when I manipulated the keyboard/mouse. Rebooted my computer and pressed F2 to get into bios, my keyboard is working fine in bios. Keyboard and mouse work fine on other computers when using USB. Found adapters for keyboard and mouse to convert from USB to PS/2 ports, works fine. I'm actually typing this question on the same keyboard, same computer, just using PS/2 ports for my mouse and keyboard. It appears to be a Windows 7 x64 issue. Other things I have tried: Multiple other mice and keyboards, iphone, all with no luck. Each one gets power, but Windows never tries to install drivers or sees that they are connected. Uninstall and reinstall all USB drivers. Drives uninstall and reinstall fine and report no errors in Control Panel. In Power Management I disallow Windows from turning off USB ports to save power Installed the latest nVidia drivers for my graphics card, no change. Anyplace else I can look/try? Thanks!

  Read the article

• Search inside of text files

  - by Matt

  So here is the situation. I currently run a mail server for my small non-profit company. My mail server (Merak Mail Server) keeps logs in .log files and mail as .tmp files. Essentially these are just text files that are kept on the server. Problem is that when I put text into the "Containing text" field on Windows Explorer, it always misses the files and tells me no results returned. Then when I search the files one by one (painful at best), I find the files I need. Do I not understand the search feature well enough, or maybe I have it indexing wrong. I really don't care what I need to use to search the files, even a third-party app is fine with me, I just want to type an email address into a box and search all of my log files or email files and find out which one I am looking for. It can be Windows Search or something else, as long as I can find a way to get the job done I will be happy. Pay solutions are fine as well. Thanks everyone in advance.

  Read the article

• Create a mailbox in qmail, then forward all incoming message to Gmail

  - by lorenzo-s

  I needed to let PHP send mails from my webserver to my web app users. So I installed qmail on my Debian server: sudo apt-get install qmail I also updated files in /etc/qmail specifing my domain name, and then I run sudo qmailctl reload and sudo qmailctl restart: /etc/qmail/defaultdomain # Contains 'mydomain.com' /etc/qmail/defaulthost # Contains 'mydomain.com' /etc/qmail/me # Contains 'mail.mydomain.com' /etc/qmail/rcpthosts # Contains 'mydomain.com' /etc/qmail/locals # Contains 'mydomain.com' Emails are sent without any problem from my PHP script to any email address, using the standard mail PHP library. Now the problem is that if I send mail from my PHP using [email protected] as sender address, I want that customer can reply to that address! And possibly, I want all mails sent to this address should be forwarded to my personal Gmail address. At the moment qmail seems to not accept any incoming mail because of "invalid mailbox name". Here is a complete SMTP session I established with my server: me@MYPC:~$ nc mydomain.com 25 220 ip-XX-XX-XXX-XXX.xxx.xxx.xxx ESMTP HELO [email protected] 250 ip-XX-XX-XXX-XXX.xxx.xxx.xxx MAIL FROM:<[email protected]> 250 ok RCPT TO:<[email protected]> 250 ok DATA 554 sorry, invalid mailbox name(s). (#5.1.1) QUIT I'm sure I missing something related to mailbox or alias creation, in fact I did nothing to define mailbox [email protected] anywhere. But I tried to search something on the net and on the numerous qmail man pages, bot I found nothing.

  Read the article

• APC uptime 0 because of Fast

  - by demlasjr

  I have a VPS using Parallels/Plesk (11.0.9 Update #22, last updated at Oct 31, 2012 03:33 AM CentOS 6.3 (Final) x86_64) I have apache (CGI/FastCGI) installed and nginx as reverse proxy. Everything is working just fine. I installed APC for caching, but the issue is that the uptime is 0 always. It's restarting each 15 seconds or so. I checked everywhere and can't find a solution to fix it. The server have the grace restart enabled, but every 6 hours, which shouldn't influence the APC uptime. Searching in Google I found that this could be related to Apache, running with FCGId instead of FastCGI. Plesk/Apache is using this config file: usr/local/psa/admin/conf/templates/default/service/php_over_fastcgi.php which content is: <IfModule mod_fcgid.c> <Files ~ (\.php)> SetHandler fcgid-script FCGIWrapper <?php echo $VAR->server->webserver->apache->phpCgiBin ?> .p$ Options +ExecCGI allow from all </Files> Is here the issue or elsewhere ? How can I fix this to work with FastCGI and make APC working properly. I forgot to specify that even if the uptime is below one minute, APC is doing pretty good job caching (92% are hits).

  Read the article

• Problems getting Cron to run processes tagged @reboot for LDAP users

  - by Ben Torell

  I have a lab of computers running Ubuntu 9.10. Most of the people who log on to these computers are users from an LDAP server, and not local users. We discovered that if an LDAP user has a crontab with an entry marked to be run @reboot, the command will not actually run upon the reboot of a machine. I'm pretty sure that this is because the cron daemon starts before networking is fully up, so the crontabs of any LDAP users aren't loaded and run or checked for @reboot. In fact, cron will ignore LDAP users' crontabs entirely after a reboot until that user runs crontab -e again and saves, or until the cron daemon is rebooted. We were able to fix one part of this problem by adding the following line to /etc/crontab: @reboot root /bin/sleep 45 && /etc/init.d/cron restart Thus, when cron starts back up upon a reboot, it waits for networking to get up, then restarts the cron daemon. That fixes the problem of crontabs not being read at all for LDAP users. However, since it's the cron daemon being restarted and not the computer, @reboot entries are ignored. Is there a way for a user to make a command run upon restarting the daemon, rather than a reboot? Or is there a better solution to this overall problem? Thanks.

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• MySQL Server hitting 100% unexpectedly (Amazon AWS RDS)

  - by Luc

  Please help! We've been struggling with this one for months. This week we upped our RDS instance to the highest performing instance and although the occurrences have reduced, we're still having our DB all of a sudden hit 100%. It comes out of nowhere. Sometimes 2am, sometimes midday. I've ruled out a DOS - our pages access logs have normal traffic I've ruled out memcached suddenly dieing (hits and misses continue as normal). The SHOW PROCESSLIST while we have issues reports about 500 queries in queue. If I kill them off or restart the server, they just keep coming back and then eventually out of knowhere, our server resumes back to normal. Sometimes up to 3 hours. Our bad performing queries take .02 seconds to execute when the server eventually returns back to normal but while we're in this 100% CPU physco phase, those queries never finish executing. Please help!!!!! Anybody know anything about MYSQL query optimization? Could it be the server deciding to use different indexes all of a sudden, which puts it into a spiral?

  Read the article

< Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >