Search Results

Search found 29319 results on 1173 pages for 'macosx 10 5'.

Page 35/1173 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• CARP: two machines think they're the master, but only on one interface

  - by Conor McDermottroe

  I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

  Read the article

• Could not find rake-10.1.0 in any of the sources

  - by spuder

  I've got a ruby on rails application (gitlab) which is installed via puppet. Everything on the test system runs fine, but production generates an error about rake Running /home/git/gitlab-shell/bin/check Could not find rake-10.1.0 in any of the sources Run bundle install to install missing gems. Here is the full rake check: root@gitlab:/home/git# sudo -u git -H bundle exec rake gitlab:check RAILS_ENV=production Checking Environment ... Git configured for git user? ... yes Has python2? ... yes python2 is supported version? ... yes Checking Environment ... Finished Checking GitLab Shell ... GitLab Shell version >= 1.7.1 ? ... OK (1.7.1) Repo base directory exists? ... yes Repo base directory is a symlink? ... no Repo base owned by git:git? ... yes Repo base access is drwxrws---? ... yes update hook up-to-date? ... yes update hooks in repos are links: ... Could not find rake-10.1.0 in any of the sources Run `bundle install` to install missing gems. gitlab-shell self-check failed Try fixing it: Make sure GitLab is running; Check the gitlab-shell configuration file: sudo -u git -H editor /home/git/gitlab-shell/config.yml Please fix the error above and rerun the checks. Checking GitLab Shell ... Finished Checking Sidekiq ... Running? ... yes Number of Sidekiq processes ... 1 Checking Sidekiq ... Finished Checking GitLab ... Database config exists? ... yes Database is SQLite ... no All migrations up? ... yes GitLab config exists? ... yes GitLab config outdated? ... no Log directory writable? ... yes Tmp directory writable? ... yes Init script exists? ... yes Init script up-to-date? ... yes projects have namespace: ... Spencer Owen / bar ... yes Projects have satellites? ... Spencer Owen / bar ... can't create, repository is empty Redis version >= 2.0.0? ... yes Your git bin path is "/usr/bin/git" Git version >= 1.7.10 ? ... yes (1.8.4) Checking GitLab ... Finished The step 'gitlab-shell check' effectively runs the following command. If I run that command manually, everything passes. root@gitlab:/home/git/gitlab# sudo -u git -H /home/git/gitlab-shell/bin/check Check GitLab API access: OK Check directories and files: /home/git/repositories: OK /home/git/.ssh/authorized_keys: OK I have verified that rake is in fact installed root@gitlab:/home/git/gitlab# gem install rake -v 10.1.0 root@gitlab:/home/git/gitlab# bundle install root@gitlab:/home/git/gitlab# sudo -u git -H gem install rake -v 10.1.0 root@gitlab:/home/git/gitlab# sudo -u git -H bundle install Ruby is installed with update alternatives root@gitlab:/home/git/gitlab# sudo -u git -H ruby --version ruby 1.9.3p0 (2011-10-30 revision 33570) [x86_64-linux] root@gitlab:/home/git/gitlab# sudo -u git -H ls -l `which ruby` lrwxrwxrwx 1 root root 22 Oct 8 20:26 /usr/bin/ruby -> /etc/alternatives/ruby root@gitlab:/home/git/gitlab# sudo -u git -H gem --version 2.1.10 root@gitlab:/home/git/gitlab# sudo -u git -H ls -l `which gem` lrwxrwxrwx 1 root root 21 Oct 10 20:50 /usr/bin/gem -> /etc/alternatives/gem I've tried the solution mentioned below, to allow shared gems http://stackoverflow.com/questions/19284914/bundle-exec-fails-with-could-not-find-rake-10-1-0-in-any-of-the-sources http://stackoverflow.com/questions/18978002/could-not-find-rake-with-bundle-exec root@gitlab:/home/git/gitlab# cat /home/git/gitlab/.bundle/config --- BUNDLE_FROZEN: '1' BUNDLE_PATH: vendor/bundle BUNDLE_WITHOUT: development:test:postgres BUNDLE_DISABLE_SHARED_GEMS: '1' I've exhausted google, so I'm hoping for someone more familiar with ruby to offer any ideas how to resolve the error. Could not find rake-10.1.0 in any of the sources

  Read the article

• "database already closed" is shown using a custom cursor adapter

  - by kiduxa

  I'm using a cursor with a custom adapter that extends SimpleCursorAdapter: public class ListWordAdapter extends SimpleCursorAdapter { private LayoutInflater inflater; private Cursor mCursor; private int mLayout; private String[] from; private int[] to; public ListWordAdapter(Context context, int layout, Cursor c, String[] from, int[] to, int flags) { super(context, layout, c, from, to, flags); this.mCursor = c; this.inflater = LayoutInflater.from(context); this.mLayout = layout; this.from = from; this.to = to; } private static class ViewHolder { //public ImageView img; public TextView name; public TextView type; public TextView translate; } @Override public View getView(int position, View convertView, ViewGroup parent) { if (mCursor.moveToPosition(position)) { ViewHolder holder; if (convertView == null) { convertView = inflater.inflate(mLayout, null); holder = new ViewHolder(); // holder.img = (ImageView) convertView.findViewById(R.id.img_row); holder.name = (TextView) convertView.findViewById(to[0]); holder.type = (TextView) convertView.findViewById(to[1]); holder.translate = (TextView) convertView.findViewById(to[2]); convertView.setTag(holder); } else { holder = (ViewHolder) convertView.getTag(); } holder.name.setText(mCursor.getString(mCursor.getColumnIndex(from[0]))); holder.type.setText(mCursor.getString(mCursor.getColumnIndex(from[1]))); holder.translate.setText(mCursor.getString(mCursor.getColumnIndex(from[2]))); // holder.img.setImageResource(img_resource); } return convertView; } } And in the main activity I call it as: adapter = new ListWordAdapter(getSherlockActivity(), R.layout.row_list_words, mCursorWords, from, to, 0); When a modification in the list is made, I call this method: public void onWordSaved() { WordDAO wordsDao = new WordSqliteDAO(); Cursor mCursorWords = wordsDao.list(getSherlockActivity()); adapter.changeCursor(mCursorWords); } The thing here is that this produces me this exception: 10-29 11:14:33.810: E/AndroidRuntime(18659): java.lang.IllegalStateException: database /data/data/com.example.palabrasdeldia/databases/palabrasDelDia (conn# 0) already closed Complete stack trace: 10-29 11:14:33.810: E/AndroidRuntime(18659): FATAL EXCEPTION: main 10-29 11:14:33.810: E/AndroidRuntime(18659): java.lang.IllegalStateException: database /data/data/com.example.palabrasdeldia/databases/palabrasDelDia (conn# 0) already closed 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.sqlite.SQLiteDatabase.verifyDbIsOpen(SQLiteDatabase.java:2123) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.sqlite.SQLiteDatabase.lock(SQLiteDatabase.java:398) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.sqlite.SQLiteDatabase.lock(SQLiteDatabase.java:390) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.sqlite.SQLiteQuery.fillWindow(SQLiteQuery.java:74) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.sqlite.SQLiteCursor.fillWindow(SQLiteCursor.java:311) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.sqlite.SQLiteCursor.onMove(SQLiteCursor.java:283) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.database.AbstractCursor.moveToPosition(AbstractCursor.java:173) 10-29 11:14:33.810: E/AndroidRuntime(18659): at com.example.palabrasdeldia.adapters.ListWordAdapter.getView(ListWordAdapter.java:42) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.AbsListView.obtainView(AbsListView.java:2128) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.ListView.makeAndAddView(ListView.java:1817) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.ListView.fillSpecific(ListView.java:1361) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.ListView.layoutChildren(ListView.java:1646) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.AbsListView.onLayout(AbsListView.java:1979) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1542) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.layoutHorizontal(LinearLayout.java:1527) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.onLayout(LinearLayout.java:1316) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.FrameLayout.onLayout(FrameLayout.java:400) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.support.v4.view.ViewPager.onLayout(ViewPager.java:1589) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.FrameLayout.onLayout(FrameLayout.java:400) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1542) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:1403) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.onLayout(LinearLayout.java:1314) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.FrameLayout.onLayout(FrameLayout.java:400) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1542) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:1403) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.LinearLayout.onLayout(LinearLayout.java:1314) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.FrameLayout.onLayout(FrameLayout.java:400) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.widget.FrameLayout.onLayout(FrameLayout.java:400) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.View.layout(View.java:9593) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewGroup.layout(ViewGroup.java:3877) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewRoot.performTraversals(ViewRoot.java:1253) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.view.ViewRoot.handleMessage(ViewRoot.java:2017) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.os.Handler.dispatchMessage(Handler.java:99) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.os.Looper.loop(Looper.java:132) 10-29 11:14:33.810: E/AndroidRuntime(18659): at android.app.ActivityThread.main(ActivityThread.java:4028) 10-29 11:14:33.810: E/AndroidRuntime(18659): at java.lang.reflect.Method.invokeNative(Native Method) 10-29 11:14:33.810: E/AndroidRuntime(18659): at java.lang.reflect.Method.invoke(Method.java:491) 10-29 11:14:33.810: E/AndroidRuntime(18659): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:844) 10-29 11:14:33.810: E/AndroidRuntime(18659): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:602) 10-29 11:14:33.810: E/AndroidRuntime(18659): at dalvik.system.NativeStart.main(Native Method) If I use SimpleCursorAdapter directly instead of ListWordAdapter, it works fine. What's wrong with my custom adapter implementation? The line in bold in the stack trace corresponds with: if (mCursor.moveToPosition(position)) inside getView method. EDIT: I have created a custom class to manage DB operations as open and close: public class ConexionBD { private Context context; private SQLiteDatabase database; private DataBaseHelper dbHelper; public ConexionBD(Context context) { this.context = context; } public ConexionBD open() throws SQLException { this.dbHelper = DataBaseHelper.getInstance(context); this.database = dbHelper.getWritableDatabase(); database.execSQL("PRAGMA foreign_keys=ON"); return this; } public void close() { if (database.isOpen() && database != null) { dbHelper.close(); } } /*Getters y setters*/ public SQLiteDatabase getDatabase() { return database; } public void setDatabase(SQLiteDatabase database) { this.database = database; } } And this is my DataBaseHelper: public class DataBaseHelper extends SQLiteOpenHelper { private static final String DATABASE_NAME = "myDb"; private static final int DATABASE_VERSION = 1; private static DataBaseHelper sInstance = null; public static DataBaseHelper getInstance(Context context) { // Use the application context, which will ensure that you // don't accidentally leak an Activity's context. // See this article for more information: http://bit.ly/6LRzfx if (sInstance == null) { sInstance = new DataBaseHelper(context.getApplicationContext()); } return sInstance; } @Override public void onCreate(SQLiteDatabase database) { ... } .... And this is an example of how I manage a query: public Cursor list(Context context) { ConexionBD conexion = new ConexionBD(context); Cursor mCursor = null; try{ conexion.open(); mCursor = conexion.getDatabase().query(DataBaseHelper.TABLE_WORD , null , null, null, null, null, Word.NAME); if (mCursor != null) { mCursor.moveToFirst(); } }finally{ conexion.close(); } return mCursor; } For every connection to the DB I open it and close it.

  Read the article

• nginx + Jetty - thousands of connections stuck in LAST_ACK

  - by virulence

  I have a FreeBSD machine with jails -- two in particular, one that runs nginx and another that runs a Java program that accepts requests via Jetty (embedded mode) Jetty receives upwards of 500 requests/sec constantly and there has been an issue lately where I will constantly have over 60,000 connections in the LAST_ACK state between nginx and jetty. Distribution of all connections (includes some other services, particularly php-fpm) root@host:/root # netstat -an > conns.txt root@host:/root # cat conns.txt | awk '{print $6}' | sort | uniq -c | sort -n 18 LISTEN 112 CLOSING 485 ESTABLISHED 650 FIN_WAIT_2 1425 FIN_WAIT_1 3301 TIME_WAIT 64215 LAST_ACK Distribution of nginx - jetty connections root@host:/root # cat conns.txt | grep '10.10.1.57' | awk '{print $6}' | sort | uniq -c | sort -n 1 3 CLOSE_WAIT 3 LISTEN 18 FIN_WAIT_2 125 ESTABLISHED 64193 LAST_ACK I'd prefer every request to fully close the connection. Clients requests are about 10 minutes apart from each other so connections must be closed. Some of the connections, tcp4 0 0 10.10.1.50.46809 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46805 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46797 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46794 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46790 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46789 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46771 10.10.1.57.9050 LAST_ACK etc.. On Jetty's end I've set maxIdleTime to 2000 -- before this all connections were in ESTABLISHED but they are now LAST_ACK On Jetty's end I've set Connection: close (i.e response.setHeader(HttpHeaders.CONNECTION, HttpHeaderValues.CLOSE);) Jetty never reports a lot of open connections -- always very few. PF/IPFW is not currently being used nginx - reset_timedout_connection is on I cannot figure out how to get nginx or jetty to forcibly close the connection, is this simply something that needs to be fixed in Jetty so that it fully closes the socket after the request finishes? Thanks a lot in advance EDIT: forgot my nginx config for the proxy setup- proxy_pass http://10.10.1.57:9050; proxy_set_header HTTP_X_GEOIP $http_x_geoip; proxy_set_header GEOIP_COUNTRY_CODE $geoip_country_code; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header Connection ""; proxy_http_version 1.1; EDIT2: Forcing Jetty to close the connection via request.getConnection().getEndPoint().close() does nothing -- it's obvious the connection IS being closed (as it's in LAST_ACK) but why isn't it getting past this? Is Nginx keeping the connection open to the backend for some reason?

  Read the article

• How to correctly add daemon in MacOS 10.6.6 via launchd?

  - by Eye of Hell

  Hello. I have a very simple task to accomplish: to start tomcat application server on latest MacOS as a daemon. I have performed following steps: Installed Tomcat in /Library/Tomcat/Home Validated that it runs fine by executed /Library/Tomcat/Home/bin/startup.sh Added org.apache.tomcat.plist file to /Library/LaunchDaemons as found on internet (http://blog.i18n.ro/complete-guide-for-installing-hudson-ci-on-os-x-10-6/) Instructed MacOS to load a daemon description via sudo launchctl load org.apache.tomcat.plist. It succeeded (issuing this command second time outputs "already loaded"). Instructed MacOS to start a daeon via sudo launchctl start org.apache.tomcat.plist At this point MacOS shows an error "launchctl start error: No such process". I have checked the logfile for launchd - it have no record for this error. Google says nothing. And from error text i can't figure out what is the "process" and why it is "wrong" :(. Any hints what i'm doing wrong?

  Read the article

• Compiling Asterisk 1.6.2 on MacOSX Server

  - by Jeremy Quinn

  I get this error while trying to compile Asterisk 1.6.2 on Snow Leopard Server : ld: symbol dyld_stub_binding_helper not defined (usually in crt1.o/dylib1.o/bundle1.o) Googling this I’ve found nothing enlightening so far. This is what I am trying: ./configure --without-h323 --without-zaptel --host=x86_64-darwin make menuselect make

  Read the article

• MacOSX: remove write-protect flag from file in Terminal

  - by Albert

  Hi, I have a file on a FAT32 volume which is shown as write-protected in Finder (so I cannot move it). Removing that write-protected flag in the information dialog works just fine. However, I have many more such files and I thus want to do it via Terminal. I already tried via 'chmod +w' but that didn't worked. 'ls -la' showed me that they are already just fine ("-rwxrwxrwx 1 az az " where az is my user account). Then I thought this might be stored in some xattr properties but 'xattr -l' didn't gave me any entry. Then I thought this might be some ACL setting (whereby I thought they would be stored as xattr but let's try it anyway) - and some Google search returned me something with 'chmod -a' or 'chmod -i' or so. All these tries only give me chmod: No ACL currently associated with file" or chmod: Failed to set ACL on file...: Operation not permitted". But I definitly have no write access to the file because I cannot move it or do any other change to it (in Terminal). Removing the write-access flag in Finder solves that.

  Read the article

• (MACOSX) - Knowing whether a mounted device was mounted from a DMG

  - by Yoni Shalom

  Well the title says it all - couldn't find that info using DiskArbitration or FSGetVolumeInfo/GetVolumeParms... I know that hdiutil uses a private framework called DiskImages framework, but I wouldn't want to run an external utility each time I want this info... wheres the API for this ? Thanks.

  Read the article

• MacOSX + Eclipse: Rename variable function not working

  - by MIsha

  Good day. I have Eclipse PHP Galileo for Mac OSX, 32bit Cocoa version. The problem is the rename function doesn't work properly. While editing PHP file I choose Refactor-Rename menu or a rename hotkey and Eclipse doesn't offer me to rename a variable, instead a rename file dialog appears. Tried to configure hotkeys but no luck. If you do know the solution – please tell. Thank you.

  Read the article

• [macosx]does dlopen call open and read functions?

  - by zbencik

  Hello, I've intercepted(interposed) dlopen function under MacOS X and some other functions. I see how my applications calls dlopen in the log, but don't find anything related to open/read functions after dynamic library was dlopened. How does the system accesses and reads the dynamic library file? I've looked at the source code of dyld, and it does call open/read on dlopen. Can anybody let me know what I'm missing? intercepted functions: dlopen, open, read, write, access, all stat functions, close, etc. thanks, any help is highly appreciated.

  Read the article

• Moving from ColdFusion 8 to ColdFusion 10 - Migration Fails

  - by XenoFoxx

  After having made several attempts to migrate from a ColdFusion 8 Standard server to a ColdFusion 10 Standard server, it feels like I am "almost" there. I'm using the 64 bit installer from Adobe's website. I'm using a Windows Server 2008 (64 bit) server with IIS 7.0. The installation itself goes smooth and the services start and are running. But at the end of the installation it says "ColdFusion Installed, but with errors" and it generates a log file. The log file reads: Migration Error: : Check that "C:\ColdFusion8" is a valid directory and is an installation of either ColdFusion MX 6 or ColdFusionMX 7 and further down says: Status: WARNING Additional Notes: WARNING - Could not migrate settings from previous version of ColdFusion Custom Action: com.macromedia.ia.action.MigrateColdFusionAction Status: ERROR Additional Notes: ERROR - class com.macromedia.ia.action.MigrateColdFusionAction NonfatalInstallException null The applicationHost.config file has new XML referencing the ColdFusion 10 directory, but IIS is still using ColdFusion 8. I'm also going to guess that the settings in the CF Administrator have not been migrated based on the message in the log above. I've followed the instructions on Adobe's site, including ensuring that ASP.NET, CGI, ISAPI Extensions, and ISAPI Filters are all enabled. I've also enabled IIS 6 Metabase Compatibility even though I don't think it's needed. Has anyone else had similar issues with ColdFusion 10 and IIS 7. Currently I have uninstalled CF 10 and reverted back to

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• Windows 8.1 in a VMWare Workstation 10 guest's mouse is missing, but only sometimes

  - by Rob Perkins

  I have VMWare Workstation 10 running on a Windows 7 machine, hosting a k guest OS. Before upgrading to WS 10 I was using version 9, and the Win8 guest OS ran without difficulty or error conditions. Since upgrading and installing the most current VMWare Tools inside the guest after upgrading to version 10, there are circumstances where the mouse pointer is not visible; the mouse position appears stuck at a screen location which is not the center of the virtualized display; and mouse click and scrolling events still get processed. Once this begins happening I have to reboot the host machine to get it to stop. (VMWare Tools 9.6.1 build-1378637 is what the WS 10 software installed) The problem seems to correlate with whether the mouse is captured during Win 8.1's bootup process, before control is passed to the login screen. If I explicitly click the mouse into the guest OS and move it slowly around while the system is booting, then I see the mouse after clicking to lift the first screen and expose the password prompt, and there is never a problem within the guest. If I don't do this during bootup, there is no mouse pointer, with the symptoms listed above. I have tried removing and reinstalling VMWare tools, and the other steps published for "mouse problems" from VMWare's chaotic troubleshooting database. The problem persists. Is there a setting in the virtual machine's configuration which could prevent this behavior?

  Read the article

• 4.4.1 Timeout in 10 minute intervals SMTP on batch email jobs

  - by TEEKAY

  I am running a job that uses SMTP and it can run in excess of an hour, emailing the entire time. It's not my code but a workflow based app so I just get a form to configure the mail server, subj, msg, etc and can't see it's implementation. I know it is .NET and SmtpClient. I have been seeing 4.4.1 timeouts every 10 minutes being reported by the application as the response from the server. The # of emails in those 10 minute sessions are variable, between 100 and below 150 which leads me to ask about the 10 minute timeout time specifically. I have found there are several exchange properties (though I don't know what version they are running) that set timeout limits. (http://technet.microsoft.com/en-us/library/bb232205%28v=exchg.150%29.aspx) Would those values for ConnectionInactivityTimeOut and ConnectionTimeout be the controlling the timeouts? and finally I would like to ask if exchange considers the consistent connection(s) it kept receiving from the same source as one continuous connection and cause the timeout each 10 minutes and cause the timeout? I am using a static ip of the mail server. Thanks if anyone can shed any light on my problem. EDIT - It is my belief that the library is just keeping the connections around and isn't wrapped in any cleanup code or using statement. That said, I still haven't made any progress on this issue in the last year and just requeue the failed ones as I see them.

  Read the article

• linux: per-process monitor, every 10 minutes, with history access

  - by Inbar Rose

  I really didn't know a better way to ask my question, hence you get a horribly named question. I will explain what i want to do, maybe that will help you help me. I would like to have my linux machine continuously monitor (every 10 minutes) all the processes on my machine. The information from each process that I require is the name, CPU usage, allocated (virtual) memory, and resident (ram) memory. If these periodic reports were to be looked at, they would look something like this: PROCESS CPU RAM VIRTUAL name1 % MB MB name2 % MB MB ...etc..etc These reports should be stored in such a way that I can access them at a later date by giving a date/time scope (range). For instance, if I want to see the history of my processes from 12:00:00 1.12.12 till 12:00:00 2.12.12 I can - and it should give me the history of the processes for every 10 minutes between those date/time borders. The format of the return is not important, that will be handled by a script anyway and can be modified into anything I need. I have looked into a few things so far, but have not found something that clearly meets my needs. Among the things i searched: sar, free(1), top(1).. and a few other things. It should be a simple issue, i can already see all this information by simply looking at my htop, but i need only a tool that will gather the desired fields for me for each processes every 10 minutes, and then also let me extract slices of that data based on date/time scopes (ranges). note: I have limited experience with linux, so please give detailed information. note2: The desired output will be something like this (after receiving the desired range) CPU USAGE BY PROCESS: proc_nameA 1,2,2,2,2,2...... numbers represent % usage every 10 minutes... proc_nameB 4,3,3,6,1,2...... The same idea with the other information.

  Read the article

• Stuck removing ffmpeg from system due to package problems

  - by Michiel

  I'd be very grateful to get a bit of support on the following situation: Using Ubuntu 12.04, and I used the PPA of Jon Severinson for ffmpeg. I had a problem playing movies with mplayer, so I decided to remove the PPA and try to use libav only after I read this article about libav vs ffmpeg. I first removed the PPA from the list, then apt-get update, etc. But I couldn't remove ffmpeg due to dependency-errors and got stuck in what seemed some kind of loop. Then I found a suggestion here. I followed the steps, and ended up force-removing libavcodec-extra-53. Because, apparently that was "what got stuff moving again". At the moment I can't. Now Ubuntu is reporting a broken package (BrokenCount 0). Errors: De afhankelijkheden van de volgende pakketten konden niet geïnstalleerd worden: audacious-plugins: Depends: audacious-plugins-data (= 3.2.1-4ubuntu1) maar 3.2.1-4ubuntu1 is geïnstalleerd Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavformat-extra-53 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libcurl3-gnutls (= 7.16.2-1) maar 7.22.0-3ubuntu4 is geïnstalleerd Depends: libgcc1 (= 1:4.1.1) maar 1:4.6.3-1ubuntu5 is geïnstalleerd Depends: libpulse0 (= 1:0.99.1) maar 1:1.1-0ubuntu15.1 is geïnstalleerd Depends: libstdc++6 (= 4.6) maar 4.6.3-1ubuntu5 is geïnstalleerd Depends: libwavpack1 (= 4.40.0) maar 4.60.1-2 is geïnstalleerd Depends: libxcomposite1 (= 1:0.3-1) maar 1:0.4.3-2build1 is geïnstalleerd Depends: zlib1g (= 1:1.1.4) maar 1:1.2.3.4.dfsg-3ubuntu4 is geïnstalleerd libavfilter-extra-2: Depends: libavcodec-extra-53 (= 6:0.10.4.0ubuntu0jon2.2) maar het is niet geïnstalleerd Depends: libavcodec-extra-53 (< 6:0.10.4.0ubuntu0jon2.2-99) maar het is niet geïnstalleerd Depends: libavformat-extra-53 (= 6:0.10.4.0ubuntu0jon2.2) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 6:0.10.4.0ubuntu0jon2.2) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libswresample-extra-0 (= 6:0.10.4.0ubuntu0jon2.2) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libswscale-extra-2 (= 6:0.10.4.0ubuntu0jon2.2) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd libavformat-extra-53: Depends: libavcodec-extra-53 (= 6:0.10.4.0ubuntu0jon2.2) maar het is niet geïnstalleerd Depends: libavcodec-extra-53 (< 6:0.10.4.0ubuntu0jon2.2-99) maar het is niet geïnstalleerd Depends: libavutil-extra-51 (= 6:0.10.4.0ubuntu0jon2.2) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd libk3b6-extracodecs: Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavformat-extra-53 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libc6 (= 2.14) maar 2.15-0ubuntu10 is geïnstalleerd Depends: libkdecore5 (= 4:4.4.4) maar 4:4.8.4a-0ubuntu0.2 is geïnstalleerd Depends: libkio5 (= 4:4.4.4) maar 4:4.8.4a-0ubuntu0.2 is geïnstalleerd Depends: libqtcore4 (= 4:4.7.0~beta1) maar 4:4.8.1-0ubuntu4.2 is geïnstalleerd Depends: libstdc++6 (= 4.1.1) maar 4.6.3-1ubuntu5 is geïnstalleerd libquicktime2: Depends: libavcodec-extra-53 (= 4:0.8~beta2-2) maar het is niet geïnstalleerd Depends: libswscale-extra-2 (= 4:0.8~beta2-2) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd libxine1-ffmpeg: Depends: libavcodec-extra-53 (= 4:0.7.3-1) maar het is niet geïnstalleerd Depends: libavutil-extra-51 (= 4:0.7.3-1) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libc6 (= 2.4) maar 2.15-0ubuntu10 is geïnstalleerd Depends: libpostproc-extra-52 (= 4:0.7.3-1) maar het is niet geïnstalleerd Depends: libxine1-bin (= 1.1.20-2build1) maar 1.1.20-2build1 is geïnstalleerd mencoder: Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavformat-extra-53 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libpostproc-extra-52 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libswscale-extra-2 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd mplayer: Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavformat-extra-53 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libpostproc-extra-52 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libswscale-extra-2 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd vlc: Depends: vlc-nox (= 2.0.3-0ubuntu0.12.04.1) maar 2.0.3-0ubuntu0.12.04.1 is geïnstalleerd Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libc6 (= 2.15) maar 2.15-0ubuntu10 is geïnstalleerd Depends: libfreetype6 (= 2.2.1) maar 2.4.8-1ubuntu2 is geïnstalleerd Depends: libgcc1 (= 1:4.1.1) maar 1:4.6.3-1ubuntu5 is geïnstalleerd Depends: libqtcore4 (= 4:4.8.0) maar 4:4.8.1-0ubuntu4.2 is geïnstalleerd Depends: libqtgui4 (= 4:4.7.0~beta1) maar 4:4.8.1-0ubuntu4.2 is geïnstalleerd Depends: libstdc++6 (= 4.6) maar 4.6.3-1ubuntu5 is geïnstalleerd Depends: zlib1g (= 1:1.2.3.3.dfsg) maar 1:1.2.3.4.dfsg-3ubuntu4 is geïnstalleerd vlc-nox: Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavformat-extra-53 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libc6 (= 2.15) maar 2.15-0ubuntu10 is geïnstalleerd Depends: libfontconfig1 (= 2.8.0) maar 2.8.0-3ubuntu9.1 is geïnstalleerd Depends: libfreetype6 (= 2.2.1) maar 2.4.8-1ubuntu2 is geïnstalleerd Depends: libgcc1 (= 1:4.1.1) maar 1:4.6.3-1ubuntu5 is geïnstalleerd Depends: libgnutls26 (= 2.12.6.1-0) maar 2.12.14-5ubuntu3.1 is geïnstalleerd Depends: libmpcdec6 (= 1:0.1~r435) maar 2:0.1~r459-1ubuntu1 is geïnstalleerd Depends: libncursesw5 (= 5.6+20070908) maar 5.9-4 is geïnstalleerd Depends: libpostproc-extra-52 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libsmbclient (= 3.0.24) maar 2:3.6.3-2ubuntu2.3 is geïnstalleerd Depends: libstdc++6 (= 4.6) maar 4.6.3-1ubuntu5 is geïnstalleerd Depends: libswscale-extra-2 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libudev0 (= 147) maar 175-0ubuntu9.1 is geïnstalleerd Depends: libxml2 (= 2.7.4) maar 2.7.8.dfsg-5.1ubuntu4.1 is geïnstalleerd Depends: zlib1g (= 1:1.2.0.2) maar 1:1.2.3.4.dfsg-3ubuntu4 is geïnstalleerd xbmc-bin: Depends: libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libavfilter-extra-2 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavformat-extra-53 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libavutil-extra-51 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd Depends: libpostproc-extra-52 (= 4:0.8-1~) maar het is niet geïnstalleerd Depends: libswscale-extra-2 (= 4:0.8-1~) maar 6:0.10.4.0ubuntu0jon2.2 is geïnstalleerd And apt-get is reporting: root@LAPTOP:~# apt-get -f install Pakketlijsten worden ingelezen... Klaar Boom van vereisten wordt opgebouwd De status informatie wordt gelezen... Klaar Vereisten worden gecorrigeerd... mislukt. De volgende pakketten hebben niet-voldane vereisten: audacious-plugins : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd libavfilter-extra-2 : Vereisten: libavcodec-extra-53 (= 6:0.10.4.0ubuntu0jon2.2) maar het is niet geïnstalleerd Vereisten: libavcodec-extra-53 (< 6:0.10.4.0ubuntu0jon2.2-99) maar het is niet geïnstalleerd libavformat-extra-53 : Vereisten: libavcodec-extra-53 (= 6:0.10.4.0ubuntu0jon2.2) maar het is niet geïnstalleerd Vereisten: libavcodec-extra-53 (< 6:0.10.4.0ubuntu0jon2.2-99) maar het is niet geïnstalleerd libk3b6-extracodecs : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd libquicktime2 : Vereisten: libavcodec53 (= 4:0.8~beta2-2) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8~beta2-2) maar het is niet geïnstalleerd libxine1-ffmpeg : Vereisten: libavcodec53 (= 4:0.7.3-1) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.7.3-1) maar het is niet geïnstalleerd mencoder : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd mplayer : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd vlc : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd vlc-nox : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd xbmc-bin : Vereisten: libavcodec53 (= 4:0.8-1~) maar het is niet geïnstalleerd of libavcodec-extra-53 (= 4:0.8-1~) maar het is niet geïnstalleerd E: Fout, pkgProblemResolver::Resolve maakte scheidingen aan, dit kan veroorzaakt worden door vastgehouden pakketten. E: Kan vereisten niet corrigeren How to proceed?? Thanks in advance, Michiel

  Read the article

• Server with 3 public IP and iptables

  - by Juan

  I have a linux box with two NIC cards: eth0 and eth1. In one card i have 3 public IP: eth0 = 10.10.10.1, eth0:1= 10.10.10.2 and eth0:2= 10.10.10.3 In the other card i have one local IP eth1 = 192.9.200.1 I want to redirect all the wan traffic for 10.10.10.2 to the LAN 192.9.200.2 and the same for 10.10.10.3 to 192.9.200.3 I have tried with this rule but doesn't work iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.2 -j DNAT --to-destination 192.9.200.2 iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.3 -j DNAT --to-destination 192.9.200.3 IP forward is enabled in /etc/sysctl.conf Can you help me, please.

  Read the article

• ssh port forwarding freezes after 10 simultaneous connections

  - by Marko Kevac

  Hello. I am using port forwarding to utilize proxy server which is on remote machine. Remote machine hostname is remotemachine. Proxy is listening on 8118 port. I am translating this port to local port 5223. ssh -vvv -N remotemachine -L 5223:localhost:8118 Everything is fine if I don't use more than 10 simultaneous connections, when ssh just freezes. It no longer send data trough port forwarding. I.e. ab -c 10 -t 5 -X 'localhost:5223' 'http://www.google.ru/' works, but ab -c 20 -t 5 -X 'localhost:5223' 'http://www.google.ru/' causes ssh to freeze MaxSessions 30 parameter in /etc/ssh/sshd_config didn't helped at all. What can I do to remove this 10 connection limit? Nothing interesting in -vvv output =(

  Read the article

• Linux software RAID 10 implementation

  - by fabrik

  Hello there! I don't want to force anybody to make it on behalf of me but trust me: i've looked hundreds of sites and i can't find a good starting point for this. I have 4x500Gb HDD's which i want to set up in RAID 10. The most promising description is here, but it's a little old and unclear for me, above all i prefer Debian over Ubuntu (i know there are slight or no differences). Is it possible to build RAID 10 with Debian's installer or i need to build RAID 1 first in the installer then use mdadm later? What is the best practice for building software RAID 10 under Linux (Debian)? Thanks for your time, fabrik

  Read the article

• How to parse json data from https client in android

  - by Madhan Shanmugam

  I try to fetch data from https client. Same code i used to fetch from http client. but its working fine. when i try to use Https client its not working. i am getting the following error. java.net.UnknownHostException: Host is unresolved: https client address:443 Error Log: 10-27 10:01:08.280: W/System.err(21826): java.net.UnknownHostException: Host is unresolved: https client address.com 443 10-27 10:01:08.290: W/System.err(21826): at java.net.Socket.connect(Socket.java:1037) 10-27 10:01:08.290: W/System.err(21826): at org.apache.http.conn.ssl.SSLSocketFactory.connectSocket(SSLSocketFactory.java:317) 10-27 10:01:08.310: W/System.err(21826): at org.apache.http.impl.conn.DefaultClientConnectionOperator.openConnection(DefaultClientConnectionOperator.java:129) 10-27 10:01:08.310: W/System.err(21826): at org.apache.http.impl.conn.AbstractPoolEntry.open(AbstractPoolEntry.java:164) 10-27 10:01:08.310: W/System.err(21826): at org.apache.http.impl.conn.AbstractPooledConnAdapter.open(AbstractPooledConnAdapter.java:119) 10-27 10:01:08.310: W/System.err(21826): at org.apache.http.impl.client.DefaultRequestDirector.execute(DefaultRequestDirector.java:348) 10-27 10:01:08.310: W/System.err(21826): at org.apache.http.impl.client.AbstractHttpClient.execute(AbstractHttpClient.java:555) 10-27 10:01:08.320: W/System.err(21826): at org.apache.http.impl.client.AbstractHttpClient.execute(AbstractHttpClient.java:487) 10-27 10:01:08.320: W/System.err(21826): at org.apache.http.impl.client.AbstractHttpClient.execute(AbstractHttpClient.java:465) 10-27 10:01:08.320: W/System.err(21826): at com.myfile.JSONParser.getJSONFromUrl(JSONParser.java:38) 10-27 10:01:08.320: W/System.err(21826): at com.myfile.myfile.processThread(myfile.java:159) 10-27 10:01:08.330: W/System.err(21826): at com.peripay.PERIPay$1$1.run(myfile.java:65) 10-27 10:01:08.330: E/Buffer Error(21826): Error converting result java.lang.NullPointerException 10-27 10:01:08.330: E/JSON Parser(21826): Error parsing data org.json.JSONException: A JSONObject text must begin with '{' at character 0 of

  Read the article

• Solaris 10 opencsw git package issue with bitbucket git hosting

  - by zephyrus00jp

  Has anyone tried using `git' from opencsw package in order to work with bitbucket source hosting service (under solaris10)? I tried to use git as the bitbucket documentation explains, and - under Debian GNU/Linux, it worked flawlessly as described, but - under Solaris 10, I got Authentication Failed message. I even tried to run truss to see anything is suspicious but could not find any smoking gun under solaris why it failed. ldd git-binary didnd't show anything suspicious either (except for the libcrypt library which could be a suspicious to think about export restrictions. Have they shipped incompatible version? BUT since the password is typed into https: connection, I suspect it is only a matter of web-level cryptography and should be universal these days.) I am now tempted to compile git suite under solaris 10, but I did find people who seem to be using git with bitbucket under solaris 10 and am wondering what could be wrong.

  Read the article

• Solaris 10 5/09 can't find SATA disk

  - by anon

  We need to run standard Solaris 10 on a few development servers (Dell 530s) because we can't get a commercial application running on OpenSolaris (we're still trying). However, we are finding that sometimes when Solaris 10 goes to do the install, after setup screens, it can't find the SATA drive. We tried the BIOS setting described here: BigAdmin On some Dells 530s, Solaris GA installs fine, but on others it doesn't. OpenSolaris always installs. Is there some way we can determine (eg. installing OpenSolaris and examining the SATA driver used) what OpenSolaris detected and use some option or driver from it to get Solaris 10 installed on our development Dell servers?

  Read the article

• How do I send information to an HLSL effect in DirectX 10?

  - by pypmannetjies

  I'd like to send my view vector to an ID3D10Effect variable in order to calculate specular lighting. How do I send a vector or even just scalar values to the HLSL from the running DirectX program? I want to do something like render() { //do transformations D3DXMatrix view = camera->getViewMatrix(); basicEffect.setVariable(viewVector, view); //render stuff }

  Read the article

• Installing Solaris 10 on sunT5220 - ZFS/UFS raid 10?

  - by Matthew

  I am in a bit of a time crunch, and need to get two T5220's built. We were very happy to see two boxes in our aged inventory which had 8 HDD's each, but didn't think to check if they were running hardware RAID or not. Turns out that they aren't. When we install, we are given the option to use UFS or ZFS, but when we select a place to install we're only given the option of installing on one single disk. Is it possible to create a software raid 10 across all of the disks and install the OS on that? Sorry if any lingo is wrong, I'm not really a Sun guy and our guru is out of town right now. Any help would be really appreciated! Note: Most of the guides I've found on google entail installing the OS on a single disk, and then creating a separate RAID 10 on other disks. We would actually like the OS to reside on the RAID 10. Hope that clarifies things.

  Read the article

• RAID 10, how layout works ?

  - by Bastien974

  I'm trying to figure out how exactly works the RAID 10 in linux with mdadm. I want to create a RAID 10 out of 4 partitions, let's say a, b, c and d. a and b are on the array 1, c and d array 2. So what I want is to have the couple a and b, c and d in RAID 0. Then on top of that, a RAID 1. The option in the mdadm command to configure the layout is -p, --layout with option : near, far, offset see here I want to keep my data safe if the array 1 fails for example, that would mean that every chunk of data are always copied on both arrays. How do I have to set my RAID 10, near or far ?

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >