Search Results

Search found 968 results on 39 pages for 'notify'.

Page 35/39 | < Previous Page | 31 32 33 34 35 36 37 38 39  | Next Page >

• unmet dependencies in Ubuntu 12.04

  - by lee.O

  I tried today to install a dvb-card on my Ubuntu 12.04 (Linux blauhai-linux 3.2.0-25-generic #40-Ubuntu SMP Wed May 23 20:30:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ). The installation failed with an error. After that, i tried to install python (it was already installed but i got this error): linux:~$ sudo apt-get install git Reading package lists... Done Building dependency tree Reading state information... Done git is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: python-glade2:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python-support:i386 (= 0.3.4) but it is not installable Depends: python:i386 (= 2.4) but it is not going to be installed Depends: libglade2-0:i386 (= 1:2.5.1) but it is not going to be installed Depends: python-gtk2:i386 (= 2.8.6-8) but it is not going to be installed python-numeric:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python:i386 (= 2.3) but it is not going to be installed Depends: python-central:i386 (= 0.5.7) but it is not installable E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). well, i can read and tried the proposed command, but then i get this: linux:~$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libopenal1:i386 libsdl-ttf2.0-0:i386 libkrb5-3:i386 libgconf-2-4:i386 libsm-dev libatk1.0-0:i386 libk5crypto3:i386 libstdc++5:i386 libqt4-declarative:i386 libxcomposite1:i386 libice-dev libgail18:i386 libldap-2.4-2:i386 libao-common libv4l-0:i386 liblcms1:i386 libqt4-qt3support:i386 libroken18-heimdal:i386 libunistring0:i386 libcupsimage2:i386 libgphoto2-port0:i386 libidn11:i386 libnss3:i386 libcaca0:i386 gtk2-engines:i386 libgudev-1.0-0:i386 libjpeg-turbo8:i386 libpthread-stubs0 libcairo-gobject2:i386 libavc1394-0:i386 libjpeg8:i386 libotr2 libaio1:i386 libsane:i386 odbcinst1debian2 odbcinst1debian2:i386 libqt4-test:i386 libqt4-script:i386 libqt4-designer:i386 libsdl-mixer1.2:i386 libqt4-network:i386 libqt4-dbus:i386 libcap2:i386 libproxy1:i386 ibus-gtk:i386 libdbus-glib-1-2:i386 libtdb1:i386 libasn1-8-heimdal:i386 libspeex1:i386 libxslt1.1:i386 libgomp1:i386 libcapi20-3:i386 libibus-1.0-0:i386 libcairo2:i386 libgnutls26:i386 libopenal-data odbcinst libgssapi3-heimdal:i386 libcanberra0:i386 libtasn1-3:i386 libfreetype6:i386 x11proto-kb-dev gtk2-engines-murrine:i386 libwavpack1:i386 libqt4-opengl:i386 libsoup-gnome2.4-1:i386 libv4lconvert0:i386 gstreamer0.10-plugins-good:i386 libc6-i386 lib32gcc1 libqt4-xmlpatterns:i386 librsvg2-common:i386 libdatrie1:i386 xtrans-dev libavahi-common-data:i386 libiec61883-0:i386 lib32asound2 libgdk-pixbuf2.0-0:i386 libsdl-image1.2:i386 libp11-kit0:i386 x11proto-input-dev libwind0-heimdal:i386 libpixman-1-0:i386 libsdl1.2debian:i386 libxaw7:i386 libgdbm3:i386 libcups2:i386 libcurl3:i386 libqtcore4:i386 libxinerama1:i386 libesd0:i386 libmikmod2:i386 libkrb5support0:i386 libxft2:i386 libxt-dev libcroco3:i386 libpulse-mainloop-glib0:i386 libice6:i386 libaa1:i386 libieee1284-3:i386 libgcrypt11:i386 libthai0:i386 libao4:i386 libkeyutils1:i386 libxmu6:i386 libcanberra-gtk0:i386 libvorbisfile3:i386 libqt4-sql:i386 esound-common libxpm4:i386 libqt4-svg:i386 libusb-0.1-4:i386 libgail-common:i386 libxrender1:i386 libhcrypto4-heimdal:i386 libraw1394-11:i386 libnspr4:i386 libshout3:i386 libdv4:i386 libhx509-5-heimdal:i386 libxau-dev libqt4-xml:i386 gstreamer0.10-x:i386 libgettextpo0:i386 libxss1:i386 libgd2-xpm:i386 libheimbase1-heimdal:i386 libtiff4:i386 libsdl-net1.2:i386 libjasper1:i386 libgnome-keyring0:i386 libxtst6:i386 gtk2-engines-pixbuf:i386 libqtgui4:i386 libtag1c2a:i386 librsvg2-2:i386 libavahi-client3:i386 libssl0.9.8:i386 libmpg123-0:i386 libmad0:i386 libsasl2-2:i386 xorg-sgml-doctools libgsoap1 gtk2-engines-oxygen:i386 libfontconfig1:i386 xaw3dg:i386 libpango1.0-0:i386 libsm6:i386 libx11-dev libheimntlm0-heimdal:i386 libpulsedsp:i386 lib32stdc++6 libx11-doc libqt4-sql-mysql:i386 libxcb-render0:i386 libodbc1:i386 libexif12:i386 libqt4-scripttools:i386 librtmp0:i386 libgssapi-krb5-2:i386 libxi6:i386 libqtwebkit4:i386 libxcb1-dev libxp6:i386 libaudio2:i386 libxcursor1:i386 libxcb-shm0:i386 libxt6:i386 libxv1:i386 libsasl2-modules:i386 libavahi-common3:i386 libxrandr2:i386 x11proto-core-dev libsqlite3-0:i386 libmng1:i386 libgtk2.0-0:i386 libxdmcp-dev libpthread-stubs0-dev libltdl7:i386 libkrb5-26-heimdal:i386 libssl1.0.0:i386 glib-networking:i386 libgpg-error0:i386 libsoup2.4-1:i386 libgphoto2-2:i386 libtag1-vanilla:i386 libaudiofile1:i386 libglade2-0:i386 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal Suggested packages: icedtea-plugin sun-java6-fonts fonts-ipafont-gothic fonts-ipafont-mincho ttf-telugu-fonts ttf-oriya-fonts ttf-kannada-fonts ttf-bengali-fonts python3-doc python3-tk python3.2-doc binfmt-support The following packages will be REMOVED: activity-log-manager-control-center aisleriot alacarte apparmor apport apport-gtk apt-xapian-index aptdaemon apturl apturl-common bluez bluez-alsa bluez-alsa:i386 bluez-gstreamer checkbox checkbox-qt command-not-found compiz compiz-gnome compiz-plugins-main-default compizconfig-backend-gconf deja-dup duplicity eog evolution-data-server firefox firefox-globalmenu firefox-gnome-support foomatic-db-compressed-ppds gconf-editor gconf2 gdb gedit gir1.2-mutter-3.0 gir1.2-peas-1.0 gir1.2-rb-3.0 gir1.2-totem-1.0 gir1.2-ubuntuoneui-3.0 gksu gnome-applets gnome-applets-data gnome-bluetooth gnome-contacts gnome-control-center gnome-media gnome-menus gnome-orca gnome-panel gnome-panel-data gnome-session-fallback gnome-shell gnome-sudoku gnome-terminal gnome-terminal-data gnome-themes-standard gnome-tweak-tool gnome-user-share gstreamer0.10-gconf gwibber gwibber-service gwibber-service-facebook gwibber-service-identica gwibber-service-twitter hplip hplip-data ia32-libs ia32-libs-multiarch:i386 ibus ibus-pinyin ibus-table indicator-datetime indicator-power jockey-common jockey-gtk landscape-client-ui-install language-selector-common language-selector-gnome launchpad-integration libcanberra-gtk-module libcanberra-gtk-module:i386 libcanberra-gtk3-module libcompizconfig0 libfolks-eds25 libgksu2-0 libgnome-media-profiles-3.0-0 libgnome2-0 libgnome2-common libgnomevfs2-0 libgnomevfs2-common libgweather-3-0 libgweather-common libgwibber-gtk2 libgwibber2 libmetacity-private0 libmutter0 libpeas-1.0-0 libpurple-bin libpython2.7 libreoffice-gnome librhythmbox-core5 libsyncdaemon-1.0-1 libtotem0 libubuntuoneui-3.0-1 light-themes lsb-release metacity metacity-common mutter-common nautilus-dropbox nautilus-share network-manager-gnome nvidia-common nvidia-settings nvidia-settings-updates onboard oneconf openjdk-7-jdk openjdk-7-jre openprinting-ppds pidgin pidgin-libnotify pidgin-otr printer-driver-foo2zjs printer-driver-ptouch printer-driver-pxljr printer-driver-sag-gdi printer-driver-splix python python-appindicator python-apport python-apt python-apt-common python-aptdaemon python-aptdaemon.gtk3widgets python-aptdaemon.pkcompat python-brlapi python-cairo python-central python-chardet python-configglue python-crypto python-cups python-cupshelpers python-dateutil python-dbus python-debian python-debtagshw python-defer python-dirspec python-egenix-mxdatetime python-egenix-mxtools python-gconf python-gdbm python-gi python-gi-cairo python-glade2:i386 python-gmenu python-gnomekeyring python-gnupginterface python-gobject python-gobject-2 python-gpgme python-gst0.10 python-gtk2 python-httplib2 python-ibus python-imaging python-keyring python-launchpadlib python-lazr.restfulclient python-lazr.uri python-libproxy python-libxml2 python-louis python-mako python-markupsafe python-minimal python-notify python-numeric:i386 python-oauth python-openssl python-packagekit python-pam python-pexpect python-piston-mini-client python-pkg-resources python-problem-report python-protobuf python-pyatspi2 python-pycurl python-pyinotify python-renderpm python-reportlab python-reportlab-accel python-serial python-simplejson python-smbc python-software-properties python-speechd python-twisted-bin python-twisted-core python-twisted-names python-twisted-web python-ubuntu-sso-client python-ubuntuone-client python-ubuntuone-control-panel python-ubuntuone-storageprotocol python-uno python-virtkey python-wadllib python-xapian python-xdg python-xkit python-zeitgeist python-zope.interface python2.7 python2.7-minimal rhythmbox rhythmbox-mozilla rhythmbox-plugin-cdrecorder rhythmbox-plugin-magnatune rhythmbox-plugin-zeitgeist rhythmbox-plugins rhythmbox-ubuntuone screen-resolution-extra sessioninstaller skype software-center software-center-aptdaemon-plugins software-properties-common software-properties-gtk system-config-printer-common system-config-printer-gnome system-config-printer-udev texlive-extra-utils totem totem-mozilla totem-plugins ubuntu-artwork ubuntu-desktop ubuntu-minimal ubuntu-sso-client ubuntu-sso-client-gtk ubuntu-standard ubuntu-system-service ubuntuone-client ubuntuone-client-gnome ubuntuone-control-panel ubuntuone-couch ubuntuone-installer ufw unattended-upgrades unity unity-2d unity-common unity-lens-applications unity-lens-video unity-scope-musicstores unity-scope-video-remote update-manager update-manager-core update-notifier update-notifier-common usb-creator-common usb-creator-gtk virtualbox virtualbox-dkms virtualbox-qt xdiagnose xul-ext-ubufox zeitgeist zeitgeist-core zeitgeist-datahub The following NEW packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal WARNING: The following essential packages will be removed. This should NOT be done unless you know exactly what you are doing! python-minimal python2.7-minimal (due to python-minimal) 0 upgraded, 16 newly installed, 273 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 39.1 MB of archives. After this operation, 324 MB disk space will be freed. You are about to do something potentially harmful. To continue type in the phrase 'Yes, do as I say!' ?] Thats not good, is it?! Should i run this command or should i run another command to fix this problem? Would be great if somebody can help me. :) Thanks in advance. best regards

  Read the article

• Stream Music and Video Over the Internet with Windows Media Player 12

  - by DigitalGeekery

  A new feature in Windows Media Player 12, which is included with Windows 7, is being able to stream media over the web to other Windows 7 computers.  Today we will take a look at how to set it up and what you need to begin. Note: You will need to perform this process on each computer that you want to use. What You’ll Need Two computers running Windows 7 Home Premium, Professional, or Ultimate. The host, or home computer that you will be streaming the media from, cannot be on a public network or part of domain. Windows Live ID UPnP or Port Forwarding enabled on your home router Media files added to your Windows Media Player library Windows Live ID Sign up online for a Windows Live ID if you do not already have one. See the link below for a link to Windows Live.   Configuring the Windows 7 Computers Open Windows Media Player and go to the library section. Click on Stream and then “Allow Internet access to home media.”   The Internet Home Media Access pop up window will prompt you to link your Windows Live ID to a user account. Click “Link an online ID.” If you haven’t already installed the Windows Live ID Sign-In Assistant, you will be taken to Microsoft’s website and prompted to download it. Once you have completed the Windows Live download assistant install, you will see Windows Live ID online provider appear in the “Link Online IDs” window. Click on “Link Online ID.” Next, you’ll be prompted for a Windows Live ID and password. Enter your Windows Live ID and password and click “Sign In.” A pop up window will notify you that you have successfully allowed Internet access to home media. Now, you will have to repeat the exact same configuration on the 2nd Windows 7 computer. Once you have completed the same configuration on your 2nd computer, you might also need to configure your home router for port forwarding. If your router supports UPnP, you may not need to manually forward any ports on your router. So, this would be a good time to test your connection. Go to a nearby hotspot, or perhaps a neighbor’s house, and test to see if you can stream your media. If not, you’ll need to manually forward the ports. You can always choose to forward the ports anyway, just in case. Note: We tested on a Linksys WRT54GL router, which supports UPnP, and found we still needed to manually forward the ports. Finding the ports to forward on the router Open Windows Media Player and make sure you are in Library view. Click on “Stream” on the top menu, and select “Allow Internet access to home media.”   On the “Internet Home Media Access” window, click on “Diagnose connections.” The “Internet Streaming Diagnostic Tool” will pop up. Click on “Port forwarding information” near the bottom.   On the “Port Forwarding Information” window you will find both the Internal and External Port numbers you will need to forward on your router. The Internal port number should always be 10245. The external number will be different depending on your computer. Microsoft also recommends forwarding port 443. Configuring the Router Next, you’ll need to configure Port Forwarding on your home router. We will show you the steps for a Linksys WRT54GL router, however, the steps for port forwarding will vary from router to router. On the Linksys configuration page, click on the Administration Tab along the top, click the “Applications & Gaming Tab, and then the “Port Range Forward” tab below it. Under “Application,” type in a name. It can be any name you choose. In both the “Start” and “End” boxes, type the port number. Enter the IP address of your home computer in the IP address column. Click the check box under “Enable.” Do this for both the internal and external port numbers and port 443. When finished, click the “Save Settings” button. Note: It’s highly recommended that you configure your home computer with a static IP address When you’re ready to play your media over the Internet, open up Windows Media Player and look for your host computer and username listed under “Other Libraries.” Click on it expand the list to see your media libraries. Choose a library and a file to play. Now you can enjoy your streaming media over the Internet. Conclusion We found media streaming over the Internet to work fairly well. However, we did see a loss of quality with streaming video. Also, Recorded TV .wtv and dvr-ms files did not play at all. Check out our previous article to see how to stream media share and stream media between Windows 7 computers on your home network. Similar Articles Productive Geek Tips Enable Media Streaming in Windows Home Server to Windows Media PlayerFixing When Windows Media Player Library Won’t Let You Add FilesShare Digital Media With Other Computers on a Home Network with Windows 7Share and Stream Digital Media Between Windows 7 Machines On Your Home NetworkLearning Windows 7: Manage Your Music with Windows Media Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7? Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox)

  Read the article

• Hundreds of unknown entries in Linux logwatch

  - by Saif Bechan

  I have a dedicated server which runs centos. Today i got an email from loginwatch on my server with hundreds of lines of 'errors'. I don't really know what they are becasue i am fairly new at this. The lines are in a few sections, I will display the first 10 of all of them, i hope someone can help me fix these problems. --------------------- Named Begin ------------------------ **Unmatched Entries** client 216.146.46.136 notify question section contains no SOA: 8 Time(s) client 92.114.98.10 query (cache) 'adobe.com/A/IN' denied: 4 Time(s) network unreachable resolving '11.254.75.75.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:13c7:7002:3000::11#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:13::c7d4:35#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:2e::1#53: 2 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::193#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::3#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:660:3006:1::1:1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:6b0:7::2#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:1:0:4777::140#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:2001:a:4608::59#53: 1 Time(s) network unreachable resolving '146.250.19.67.in-addr.arpa/PTR/IN': 2001:5a0:10::2#53: 1 Time(s) network unreachable resolving '149.207.106.87.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '178.62.24.195.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) this goes on for hundreds of lines with all different domain names. --------------------- pam_unix Begin ------------------------ Failed logins from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 111 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 113 times 121.14.145.32: 136 times 190.152.69.5: 248 times 209.160.72.15: 572 times 210.26.48.35: 2 times 212.235.111.224 (DSL212-235-111-224.bb.netvision.net.il): 140 times 218.206.25.29: 140 times Illegal users from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 2665 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 2539 times 121.14.145.32: 116 times 190.152.69.5: 34 times 209.160.72.15: 324 times 218.206.25.29: 8051 times proftpd: Unknown Entries: session opened for user cent_ftp by (uid=0): 15 Time(s) session closed for user cent_ftp: 14 Time(s) sshd: Authentication Failures: unknown (218.206.25.29): 8051 Time(s) unknown (78-86-126-211.zone2.bethere.co.uk): 2665 Time(s) unknown (93.97.176.136): 2539 Time(s) root (209.160.72.15): 558 Time(s) unknown (209.160.72.15): 324 Time(s) root (190.152.69.5): 246 Time(s) unknown (121.14.145.32): 116 Time(s) root (121.14.145.32): 106 Time(s) root (dsl212-235-111-224.bb.netvision.net.il): 70 Time(s) root (93.97.176.136): 44 Time(s) root (78-86-126-211.zone2.bethere.co.uk): 37 Time(s) unknown (190.152.69.5): 34 Time(s) mysql (121.14.145.32): 30 Time(s) nobody (218.206.25.29): 26 Time(s) mail (218.206.25.29): 24 Time(s) news (218.206.25.29): 24 Time(s) root (218.206.25.29): 24 Time(s) --------------------- SSHD Begin ------------------------ **Unmatched Entries** pam_succeed_if(sshd:auth): error retrieving information about user tavi : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pam : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user konchog : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user stavrum : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user rachel : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user affiliates : 24 time(s) pam_succeed_if(sshd:auth): error retrieving information about user nen : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cobra : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pass : 7 time(s) pam_succeed_if(sshd:auth): error retrieving information about user hacer : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user chung : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user zainee : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user radu : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user alka : 4 time(s) pam_succeed_if(sshd:auth): error retrieving information about user albert : 5 time(s) pam_succeed_if(sshd:auth): error retrieving information about user turcia : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cordell : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user silver : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user dragon : 3 time(s) If someone wants to see the whole log i can upload it somewhere. Am i being hacked, what is this all?? I hope someone can help me, this does not look good at all.

  Read the article

• Redirect network logs from syslog to another file

  - by w0rldart

  I keep logging way to much info (not needed, for now) in my syslog, and not daily or hourly... but instant. If I want to watch for something in my syslog I just can't because the network log keeps interfering. So, how can I redirect network logs to another file and/or stop logging it? Dec 10 17:01:33 user kernel: [ 8716.000587] MediaState is connected Dec 10 17:01:33 user kernel: [ 8716.000599] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:33 user kernel: [ 8716.000601] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:33 user kernel: [ 8716.000612] rt28xx_get_wireless_stats ---> Dec 10 17:01:33 user kernel: [ 8716.000615] <--- rt28xx_get_wireless_stats Dec 10 17:01:39 user kernel: [ 8722.000714] MediaState is connected Dec 10 17:01:39 user kernel: [ 8722.000729] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:39 user kernel: [ 8722.000732] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:39 user kernel: [ 8722.000747] rt28xx_get_wireless_stats ---> Dec 10 17:01:39 user kernel: [ 8722.000751] <--- rt28xx_get_wireless_stats Dec 10 17:01:44 user kernel: [ 8726.904025] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:01:45 user kernel: [ 8728.003138] MediaState is connected Dec 10 17:01:45 user kernel: [ 8728.003153] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:45 user kernel: [ 8728.003157] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:45 user kernel: [ 8728.003171] rt28xx_get_wireless_stats ---> Dec 10 17:01:45 user kernel: [ 8728.003175] <--- rt28xx_get_wireless_stats Dec 10 17:01:51 user kernel: [ 8734.004066] MediaState is connected Dec 10 17:01:51 user kernel: [ 8734.004079] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:51 user kernel: [ 8734.004082] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:51 user kernel: [ 8734.004096] rt28xx_get_wireless_stats ---> Dec 10 17:01:51 user kernel: [ 8734.004099] <--- rt28xx_get_wireless_stats Dec 10 17:01:57 user kernel: [ 8740.004108] MediaState is connected Dec 10 17:01:57 user kernel: [ 8740.004119] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:57 user kernel: [ 8740.004121] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:57 user kernel: [ 8740.004132] rt28xx_get_wireless_stats ---> Dec 10 17:01:57 user kernel: [ 8740.004135] <--- rt28xx_get_wireless_stats Dec 10 17:01:57 user kernel: [ 8740.436021] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:03 user kernel: [ 8746.005280] MediaState is connected Dec 10 17:02:03 user kernel: [ 8746.005294] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:03 user kernel: [ 8746.005298] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:03 user kernel: [ 8746.005312] rt28xx_get_wireless_stats ---> Dec 10 17:02:03 user kernel: [ 8746.005315] <--- rt28xx_get_wireless_stats Dec 10 17:02:09 user kernel: [ 8752.004790] MediaState is connected Dec 10 17:02:09 user kernel: [ 8752.004804] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:09 user kernel: [ 8752.004808] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:09 user kernel: [ 8752.004821] rt28xx_get_wireless_stats ---> Dec 10 17:02:09 user kernel: [ 8752.004825] <--- rt28xx_get_wireless_stats Dec 10 17:02:15 user kernel: [ 8757.984031] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:15 user kernel: [ 8758.004078] MediaState is connected Dec 10 17:02:15 user kernel: [ 8758.004094] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:15 user kernel: [ 8758.004097] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:15 user kernel: [ 8758.004112] rt28xx_get_wireless_stats ---> Dec 10 17:02:15 user kernel: [ 8758.004116] <--- rt28xx_get_wireless_stats Dec 10 17:02:16 user kernel: [ 8759.492017] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:19 user kernel: [ 8762.002179] SCANNING, suspend MSDU transmission ... Dec 10 17:02:19 user kernel: [ 8762.004291] MlmeScanReqAction -- Send PSM Data frame for off channel RM, SCAN_IN_PROGRESS=1! Dec 10 17:02:19 user kernel: [ 8762.025055] SYNC - BBP R4 to 20MHz.l Dec 10 17:02:19 user kernel: [ 8762.027249] RT35xx: SwitchChannel#1(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF1, K=0x02, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.170206] RT35xx: SwitchChannel#2(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF1, K=0x07, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.318211] RT35xx: SwitchChannel#3(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF2, K=0x02, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.462269] RT35xx: SwitchChannel#4(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF2, K=0x07, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.606229] RT35xx: SwitchChannel#5(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF3, K=0x02, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.750202] RT35xx: SwitchChannel#6(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF3, K=0x07, R=0x02 Dec 10 17:02:20 user kernel: [ 8762.894217] RT35xx: SwitchChannel#7(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF4, K=0x02, R=0x02 Dec 10 17:02:20 user kernel: [ 8763.038202] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:20 user kernel: [ 8763.040194] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:20 user kernel: [ 8763.040199] BAR(1) : Tid (0) - 03a3:037e Dec 10 17:02:20 user kernel: [ 8763.040387] SYNC - End of SCAN, restore to channel 11, Total BSS[03] Dec 10 17:02:20 user kernel: [ 8763.040400] ScanNextChannel -- Send PSM Data frame Dec 10 17:02:20 user kernel: [ 8763.040402] bFastRoamingScan ~~~~~~~~~~~~~ Get back to send data ~~~~~~~~~~~~~ Dec 10 17:02:20 user kernel: [ 8763.040405] SCAN done, resume MSDU transmission ... Dec 10 17:02:20 user kernel: [ 8763.047022] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:20 user kernel: [ 8763.047026] BAR(1) : Tid (0) - 03a3:03a5 Dec 10 17:02:21 user kernel: [ 8763.898130] bImprovedScan ............. Resume for bImprovedScan, SCAN_PENDING .............. Dec 10 17:02:21 user kernel: [ 8763.898143] SCANNING, suspend MSDU transmission ... Dec 10 17:02:21 user kernel: [ 8763.900245] MlmeScanReqAction -- Send PSM Data frame for off channel RM, SCAN_IN_PROGRESS=1! Dec 10 17:02:21 user kernel: [ 8763.921144] SYNC - BBP R4 to 20MHz.l Dec 10 17:02:21 user kernel: [ 8763.923339] RT35xx: SwitchChannel#8(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF4, K=0x07, R=0x02 Dec 10 17:02:21 user kernel: [ 8763.996019] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:21 user kernel: [ 8764.066221] RT35xx: SwitchChannel#9(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF5, K=0x02, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.210212] RT35xx: SwitchChannel#10(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF5, K=0x07, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.215536] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.215542] BAR(1) : Tid (0) - 0457:0452 Dec 10 17:02:21 user kernel: [ 8764.244000] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.244004] BAR(1) : Tid (0) - 0459:0456 Dec 10 17:02:21 user kernel: [ 8764.253019] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.253023] BAR(1) : Tid (0) - 045c:0458 Dec 10 17:02:21 user kernel: [ 8764.256677] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.256681] BAR(1) : Tid (0) - 045c:045b Dec 10 17:02:21 user kernel: [ 8764.259785] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.259788] BAR(1) : Tid (0) - 045d:045b Dec 10 17:02:21 user kernel: [ 8764.280467] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.280471] BAR(1) : Tid (0) - 045f:045c Dec 10 17:02:21 user kernel: [ 8764.282189] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.282192] BAR(1) : Tid (0) - 045f:045e Dec 10 17:02:21 user kernel: [ 8764.354204] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.356408] ScanNextChannel():Send PWA NullData frame to notify the associated AP! Dec 10 17:02:21 user kernel: [ 8764.498202] RT35xx: SwitchChannel#12(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x07, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.642210] RT35xx: SwitchChannel#13(RF=8, Pwr0=30, Pwr1=28, 2T), N=0xF7, K=0x02, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.790229] RT35xx: SwitchChannel#14(RF=8, Pwr0=30, Pwr1=28, 2T), N=0xF8, K=0x04, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.934238] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.935243] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:22 user kernel: [ 8764.935249] BAR(1) : Tid (0) - 048e:0485 Dec 10 17:02:22 user kernel: [ 8764.936423] SYNC - End of SCAN, restore to channel 11, Total BSS[05] Dec 10 17:02:22 user kernel: [ 8764.936436] ScanNextChannel -- Send PSM Data frame Dec 10 17:02:22 user kernel: [ 8764.936440] SCAN done, resume MSDU transmission ... Dec 10 17:02:22 user kernel: [ 8764.940529] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.942178] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:22 user kernel: [ 8764.942182] BAR(1) : Tid (0) - 0493:048e Dec 10 17:02:22 user kernel: [ 8764.942715] CNTL - All roaming failed, restore to channel 11, Total BSS[05] Dec 10 17:02:22 user kernel: [ 8764.948016] MMCHK - No BEACON. restore R66 to the low bound(56) Dec 10 17:02:22 user kernel: [ 8764.948307] ===>rt_ioctl_giwscan. 5(5) BSS returned, data->length = 1111 Dec 10 17:02:23 user kernel: [ 8766.048073] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:23 user kernel: [ 8766.552034] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:27 user kernel: [ 8770.001180] MediaState is connected Dec 10 17:02:27 user kernel: [ 8770.001197] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:27 user kernel: [ 8770.001201] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:27 user kernel: [ 8770.001219] rt28xx_get_wireless_stats ---> Dec 10 17:02:27 user kernel: [ 8770.001223] <--- rt28xx_get_wireless_stats Dec 10 17:02:28 user kernel: [ 8771.564020] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:29 user kernel: [ 8772.064031] QuickDRS: TxTotalCnt <= 15, train back to original rate

  Read the article

• [GEEK SCHOOL] Network Security 4: Windows Firewall: Your System’s Best Defense

  - by Ciprian Rusen

  If you have your computer connected to a network, or directly to your Internet connection, then having a firewall is an absolute necessity. In this lesson we will discuss the Windows Firewall – one of the best security features available in Windows! The Windows Firewall made its debut in Windows XP. Prior to that, Windows system needed to rely on third-party solutions or dedicated hardware to protect them from network-based attacks. Over the years, Microsoft has done a great job with it and it is one of the best firewalls you will ever find for Windows operating systems. Seriously, it is so good that some commercial vendors have decided to piggyback on it! Let’s talk about what you will learn in this lesson. First, you will learn about what the Windows Firewall is, what it does, and how it works. Afterward, you will start to get your hands dirty and edit the list of apps, programs, and features that are allowed to communicate through the Windows Firewall depending on the type of network you are connected to. Moving on from there, you will learn how to add new apps or programs to the list of allowed items and how to remove the apps and programs that you want to block. Last but not least, you will learn how to enable or disable the Windows Firewall, for only one type of networks or for all network connections. By the end of this lesson, you should know enough about the Windows Firewall to use and manage it effectively. What is the Windows Firewall? Windows Firewall is an important security application that’s built into Windows. One of its roles is to block unauthorized access to your computer. The second role is to permit authorized data communications to and from your computer. Windows Firewall does these things with the help of rules and exceptions that are applied both to inbound and outbound traffic. They are applied depending on the type of network you are connected to and the location you have set for it in Windows, when connecting to the network. Based on your choice, the Windows Firewall automatically adjusts the rules and exceptions applied to that network. This makes the Windows Firewall a product that’s silent and easy to use. It bothers you only when it doesn’t have any rules and exceptions for what you are trying to do or what the programs running on your computer are trying to do. If you need a refresher on the concept of network locations, we recommend you to read our How-To Geek School class on Windows Networking. Another benefit of the Windows Firewall is that it is so tightly and nicely integrated into Windows and all its networking features, that some commercial vendors decided to piggyback onto it and use it in their security products. For example, products from companies like Trend Micro or F-Secure no longer provide their proprietary firewall modules but use the Windows Firewall instead. Except for a few wording differences, the Windows Firewall works the same in Windows 7 and Windows 8.x. The only notable difference is that in Windows 8.x you will see the word “app” being used instead of “program”. Where to Find the Windows Firewall By default, the Windows Firewall is turned on and you don’t need to do anything special in order for it work. You will see it displaying some prompts once in a while but they show up so rarely that you might forget that is even working. If you want to access it and configure the way it works, go to the Control Panel, then go to “System and Security” and select “Windows Firewall”. Now you will see the Windows Firewall window where you can get a quick glimpse on whether it is turned on and the type of network you are connected to: private networks or public network. For the network type that you are connected to, you will see additional information like: The state of the Windows Firewall How the Windows Firewall deals with incoming connections The active network When the Windows Firewall will notify you You can easily expand the other section and view the default settings that apply when connecting to networks of that type. If you have installed a third-party security application that also includes a firewall module, chances are that the Windows Firewall has been disabled, in order to avoid performance issues and conflicts between the two security products. If that is the case for your computer or device, you won’t be able to view any information in the Windows Firewall window and you won’t be able to configure the way it works. Instead, you will see a warning that says: “These settings are being managed by vendor application – Application Name”. In the screenshot below you can see an example of how this looks. How to Allow Desktop Applications Through the Windows Firewall Windows Firewall has a very comprehensive set of rules and most Windows programs that you install add their own exceptions to the Windows Firewall so that they receive network and Internet access. This means that you will see prompts from the Windows Firewall on occasion, generally when you install programs that do not add their own exceptions to the Windows Firewall’s list. In a Windows Firewall prompt, you are asked to select the network locations to which you allow access for that program: private networks or public networks. By default, Windows Firewall selects the checkbox that’s appropriate for the network you are currently using. You can decide to allow access for both types of network locations or just to one of them. To apply your setting press “Allow access”. If you want to block network access for that program, press “Cancel” and the program will be set as blocked for both network locations. At this step you should note that only administrators can set exceptions in the Windows Firewall. If you are using a standard account without administrator permissions, the programs that do not comply with the Windows Firewall rules and exceptions are automatically blocked, without any prompts being shown. You should note that in Windows 8.x you will never see any Windows Firewall prompts related to apps from the Windows Store. They are automatically given access to the network and the Internet based on the assumption that you are aware of the permissions they require based on the information displayed by the Windows Store. Windows Firewall rules and exceptions are automatically created for each app that you install from the Windows Store. However, you can easily block access to the network and the Internet for any app, using the instructions in the next section. How to Customize the Rules for Allowed Apps Windows Firewall allows any user with an administrator account to change the list of rules and exceptions applied for apps and desktop programs. In order to do this, first start the Windows Firewall. On the column on the left, click or tap “Allow an app or feature through Windows Firewall” (in Windows 8.x) or “Allow a program or feature through Windows Firewall” (in Windows 7). Now you see the list of apps and programs that are allowed to communicate through the Windows Firewall. At this point, the list is grayed out and you can only view which apps, features, and programs have rules that are enabled in the Windows Firewall.

  Read the article

• Can't send mail from Windows Phone (Postfix server)

  - by Dominic Williams

  Some background: I have a Dovecot/Postfix setup to handle email for a few domains. We have imap and smtp setup on various devices (Macs, iPhones, PCs, etc) and it works no problem. I've recently bought a Windows Phone and I'm trying to setup the mail account on there. I've got the imap part working great but for some reason it won't send mail. mail.log with debug_peer_list I've put this on pastebin because its quite long: http://pastebin.com/KdvMDxTL dovecot.log with verbose_ssl Apr 14 22:43:50 imap-login: Warning: SSL: where=0x10, ret=1: before/accept initialization [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: before/accept initialization [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 read client hello A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 write server hello A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 write certificate A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 write server done A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 flush data [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2002, ret=-1: SSLv3 read client certificate A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2002, ret=-1: SSLv3 read client certificate A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 read client key exchange A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 read finished A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 write change cipher spec A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 write finished A [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2001, ret=1: SSLv3 flush data [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x20, ret=1: SSL negotiation finished successfully [109.151.23.129] Apr 14 22:43:50 imap-login: Warning: SSL: where=0x2002, ret=1: SSL negotiation finished successfully [109.151.23.129] Apr 14 22:43:51 imap-login: Info: Login: user=<pixelfolio>, method=PLAIN, rip=109.151.23.129, lip=94.23.254.175, mpid=24390, TLS Apr 14 22:43:53 imap(pixelfolio): Info: Disconnected: Logged out bytes=9/331 Apr 14 22:43:53 imap-login: Warning: SSL alert: where=0x4008, ret=256: warning close notify [109.151.23.129] postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix debug_peer_list = 109.151.23.129 inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 message_size_limit = 50240000 milter_default_action = accept milter_protocol = 2 mydestination = ks383809.kimsufi.com, localhost.kimsufi.com, localhost myhostname = ks383809.kimsufi.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname non_smtpd_milters = inet:127.0.0.1:8891,inet:localhost:8892 readme_directory = no recipient_delimiter = + smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_milters = inet:127.0.0.1:8891,inet:localhost:8892 smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes virtual_alias_domains = domz.co.uk ruck.in vjgary.co.uk scriptees.co.uk pixelfolio.co.uk filmtees.co.uk nbsbar.co.uk virtual_alias_maps = hash:/etc/postfix/alias_maps doveconf -n # 2.0.13: /etc/dovecot/dovecot.conf # OS: Linux 2.6.38.2-grsec-xxxx-grs-ipv6-64 x86_64 Ubuntu 11.10 auth_mechanisms = plain login log_path = /var/log/dovecot.log mail_location = mbox:~/mail/:INBOX=/var/mail/%u passdb { driver = pam } protocols = imap service auth { unix_listener /var/spool/postfix/private/auth { group = postfix mode = 0660 user = postfix } } ssl_cert = </etc/ssl/certs/dovecot.pem ssl_key = </etc/ssl/private/dovecot.pem userdb { driver = passwd } verbose_ssl = yes Any suggestions or help greatly appreciated. I've been pulling my hair out with this for hours! EDIT This seems to be my exact problem, but I already have broken_sasl set to yes and the 'login' auth mechanism added? http://forums.gentoo.org/viewtopic-t-898610-start-0.html

  Read the article

• CodePlex Daily Summary for Sunday, May 02, 2010

  CodePlex Daily Summary for Sunday, May 02, 2010New ProjectsAdventureWorks in Access: AdventureWorks database in Access format. Data has been ported in Access starting from Adventure Works database for SQL Server 2008.amplifi: This project is still under construction. We will add more information here as soon as it is available.ASP.NET MVC Bug Tracker: Bug Track written in C# ASP.NET MVC 2BigDecimal: BigDecimal is an attempt to create a number class that can have large precision. It is developed in vb.net (.net 4).CBM-Command: Coming soon....Chuyou: ChuyouCMinus: A C Minus Compiler!Complex and advanced mathematical functions: Mathematics toolkit is a Class Library Project which help Programmers to Calculate Mathematics Functions easily.Confuser: Confuser is a obfuscator for .NET. It is developed in C# and using Mono.Cecil for assembly manipulation.easypos: Micro punto de venta que permite ventas express de ropa, que se acopla fácil y transaparente con el ERP Click OneElmech Address Book: Web based Address Book for maintaining details of your business clients. This project targets Suppliers - Traders - Manufacturers - users. Applicat...Feed Viewer: Feed Viewer is able to synchronize subscribed feed and red news among all computers you are using. It understands both RSS and Atom format. It can ...Google URL Shortener, C#: Implementation in C# of generating short URLs by Goo.gl service (Google URL Shortener)MARS - Medical Assistant Record System: MARS - Medical Assistant Record SystemRx Contrib: Rx Contrib is a library which contain extensions for the Rx frameworkSimple Service Administration Tool: A simple tool to start/stop/restart a service of a WinNT based system. The tool is placed in the task bar as a notify icon, so the specified servic...Vis3D: Visual 3D controls for Silverlight.VisContent: XML content controls for ASP.NET.Windows Phone 7 database: This project implements a Isolated Storage (IsolatedStorage) based database for Windows Phone 7. The database consists of table object, each one s...New Releases$log$ / Keyword Substitution / Expansion Check-In Policy (TFS - LogSubstPol): LogSubstPol_v1.2010.0.4 (VS2010): LogSubstPol is a TFS check-in policy which insertes the check-in comments and other keywords into your source code, so you can keep track of the ch...Bojinx: Bojinx Core V4.5.1: The following new features were added: You can now use either BojinxMXMLContext or ContextModule to configure your application or module context. ...CBM-Command: Initial Public Demonstration: Initial public demonstration version. Can browse attached drives and display directory of any attached drive. A common question is "How does it w...Confuser: Confuser v1.0: It is the Confuser v1.0 that used to confuse the reverse-engineers :)Font Family Name Retrieval: 2nd Release: Added New MKV Font Extractor application to showcase the library. MKV Font Extractor depends on MKVToolnix to be installed before it will work. R...Google URL Shortener, C#: Goo.gl-CS v1 Beta: Extract the ZIP file to any location. Two files have to be in the same folder!HouseFly controls: HouseFly controls alpha 0.9.6.1: HouseFly controls release 0.9.6.1 alphaIsWiX: IsWiX 1.0.261.0: Build 1.0.261.0 - built against Fireworks 1.0.264.0. Adds support for VS2010 Integration to support WiX 3.5 beta releases.Managed Extensibility Framework (MEF) Contrib: MefContrib 0.9.2.0: Added conventions based catalog (read more at http://www.thecodejunkie.com/2010/03/bringing-convention-based-registration.html) MEF + Unity integ...MARS - Medical Assistant Record System: license: licenseNSIS Autorun: NSIS Autorun 0.1.5: This release includes source code, executable binary, files and example materials.PHP.net: Release 0.0.0.1: This is the first release of PHP.Net. The features available in this release are: new File Save File Save As Open File In the rar file is th...Rx Contrib: V1: Rx Contrib is ongoing effort for community additions for Rx. Current features are: ReactiveQueue: ISubject that does not loose values if there are ...Silverlight 4.0 Popup Menu: Context Menu for Silverlight 4 v1.0: - Added a margin for icon display. - Added the PopupMenuItem class which is a derivative of the DockPanel. - Find* methods can now drill down the v...Silverlight 4.0 Popup Menu: Context Menu for Silverlight 4 v1.1 Beta: - Added a margin for icon display. - Added the PopupMenuItem class which is a derivative of the DockPanel. - Added a AddSeperator method. - The Fin...Simple Service Administration Tool: SSATool 0.1.3: New Simple Service Administration Tool Version 0.1.3 compiled with Visual Studio .NET 2010.sMAPedit: sMAPedit v0.7a + Map-Pack: Required Additional Map-Pack Added: height setting by color picker (shift+leftclick)sMAPedit: sMAPedit v0.7b: Fixed: force a gargabe collection update to prevent pictureBox's memory leaksqwarea: Sqwarea 0.0.228.0 (alpha): This release corrects a critical bug in ConnexityNotifier service. We strongly recommend you to upgrade to this version. Known bugs : if you open...StackOverflow Desktop Client in C# and WPF: StackOverflow Client 0.1: Source code for the sample.TortoiseHg: TortoiseHg 1.0.2: This is a bug fix release, we recommend all users upgrade to 1.0.2VCC: Latest build, v2.1.30501.0: Automatic drop of latest buildVidCoder: 0.4.0: Changes: Added ability to queue up multiple video files or titles at once. These queued jobs will use the currently selected encoding settings. Mul...WabbitStudio Z80 Software Tools: Wabbitemu 32-bit Test Release: Wabbitemu Visual Studio build for testing purposesWindows Phone 7 database: Initial Release v1.0: This project implements a Isolated Storage (IsolatedStorage) based database for Windows Phone 7. The usage of this software is very simple. You cre...YouTubeEmbeddedVideo WebControl for ASP.NET: VideoControls version 1: This zip file contains the VideoControls.dll, version 1.Most Popular ProjectsRawrWBFS ManagerAJAX Control Toolkitpatterns & practices – Enterprise LibraryMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)iTuner - The iTunes CompanionASP.NETDotNetNuke® Community EditionMost Active Projectspatterns & practices – Enterprise LibraryRawrIonics Isapi Rewrite FilterHydroServer - CUAHSI Hydrologic Information System Serverpatterns & practices: Azure Security GuidanceTinyProjectNB_Store - Free DotNetNuke Ecommerce Catalog ModuleBlogEngine.NETDambach Linear Algebra FrameworkFacebook Developer Toolkit

  Read the article

• How do you handle authentication across domains?

  - by William Ratcliff

  I'm trying to save users of our services from having to have multiple accounts/passwords. I'm in a large organization and there's one group that handles part of user authentication for users who are from outside the facility (primarily for administrative functions). They store a secure cookie to establish a session and communicate only via HTTPS via the browser. Sessions expire either through: 1) explicit logout of the user 2) Inactivity 3) Browser closes My team is trying to write a web application to help users analyze data that they've taken (or are currently taking) while at our facility. We need to determine if a user is 1) authenticated 2) Some identifier for that user so we can store state for them (what analysis they are working on, etc.) So, the problem is how do you authenticate across domains (the authentication server for the other application lives in a border region between public and private--we will live in the public region). We have come up with some scenarios and I'd like advice about what is best practice, or if there is one we haven't considered. Let's start with the case where the user is authenticated with the authentication server. 1) The authentication server leaves a public cookie in the browser with their primary key for a user. If this is deemed sensitive, they encrypt it on their server and we have the key to decrypt it on our server. When the user visits our site, we check for this public cookie. We extract the user_id and use a public api for the authentication server to request if the user is logged in. If they are, they send us a response with: response={ userid :we can then map this to our own user ids. If necessary, we can request additional information such as email-address/display name once (to notify them if long running jobs are done, or to share results with other people, like with google_docs). account_is_active:Make sure that the account is still valid session_is_active: Is their session still active? If we query this for a valid user, this will have a side effect that we will reset the last_time_session_activated value and thus prolong their session with the authentication server last_time_session_activated: let us know how much time they have left ip_address_session_started_from:make sure the person at our site is coming from the same ip as they started the session at } Given this response, we either accept them as authenticated and move on with our app, or redirect them to the login page for the authentication server (question: if we give an encrypted portion of the response (signed by us) with the page to redirect them to, do we open any gaping security holes in the authentication server)? The flaw that we've found with this is that if the user visits evilsite.com and they look at the session cookie and send a query to the public api of the authentication server, they can keep the session alive and if our original user leaves the machine without logging out, then the next user will be able to access their session (this was possible before, but having the session alive eternally makes this worse). 2) The authentication server redirects all requests made to our domain to us and we send responses back through them to the user. Essentially, they act as a proxy. The advantage of this is that we can handshake with the authentication server, so it's safe to be trusted with the email address/name of the user and they don't have to reenter it So, if the user tries to go to: authentication_site/mysite_page1 they are redirected to mysite. Which would you choose, or is there a better way? The goal is to minimize the "Yet Another Password/Yet another username" problem... Thanks!!!!

  Read the article

• New OFM versions released SOA Suite 11.1.1.4 &amp; BPM 11.1.1.4 &amp; JDeveloper 11.1.1.4 WebLogic on JRockit 10.3.4 feedback from the community

  - by Jürgen Kress

  Oracle SOA Suite 11g Installations This is the latest release of the Oracle SOA Suite 11g. Please see the Documentation tab for Release Notes, Installation Guides and other release specific information. Please also see the List of New Features and Samples provided for this release. Release 11gR1 (11.1.1.4.0) Microsoft Windows (32-bit JVM) Linux (32-bit JVM) Generic Oracle JDeveloper 11g Rel 1 (11.1.1.x) (JDeveloper + ADF) Integrated development environment certified on Windows, Linux, and Macintosh. License is free (read the Pricing FAQ). Studio Edition for Windows (1.2 GB) | Studio Edition for Linux (1.3 GB) | See All See Additional Development Tools Oracle WebLogic Server 11g Rel 1 (10.3.4) Installers The WebLogic Server installers include Oracle Coherence and Oracle Enterprise Pack for Eclipse and supports development with other Fusion Middleware products . The zip includes WebLogic Server only and is intended for WebLogic Server development only. Linux x86 (1.1 GB) | Windows x86 (1 GB) Zip for Windows x86, Linux x86, Mac OS X (316 MB) | See All Oracle WebLogic Server 11gR1 (10.3.4) on JRockit Virtual Edition Download For additional downloads please visit the Oracle Fusion Middleware Products Update Center Share your feedback with the @soacommunity on twitter SOASimone Simone Geib SOA Suite 11gR1 (11.1.1.4.0) has just been released: http://www.oracle.com/technetwork/middleware/soasuite/downloads/index.html gschmutz gschmutz My new blog post: WebLogic Server, JDev, SOA, BPM, OSB and CEP 11.1.1.4 (PS3) available! - http://tinyurl.com/4negnpn simon_haslam Simon Haslam I'm very pleased to see WLS 10.3.4 for JRockit VE launched at the same time as the rest of PS3 http://j.mp/gl1nQm (32bit anyway) lucasjellema Lucas Jellema See http://www.oracle.com/ocom/groups/public/@otn/documents/webcontent/156082.xml for PS3 extension downloads BPM, SOA Editor, WebCenter demed demed List of new features in @OracleSOA 11gR1 PS3: http://bit.ly/fVRwsP is not extremely long but huge release by # of bugs fixed. Go! biemond Edwin Biemond WebLogic 10.3.4 new features http://bit.ly/f7L1Eu Exalogic Elastic Cloud , JPA2 , Maven plugin, OWSM policies on WebLogic SCA applications JDeveloper JDeveloper & ADF JDeveloper and Oracle ADF 11g Release 1 Patch Set 3 (11.1.1.4.0): New Features and Bug Fixes http://bit.ly/feghnY simon_haslam Simon Haslam WebLogic Server 10.3.4 (i.e. 11gR1 PS3) available now too http://bit.ly/eeysZ2 JDeveloper JDeveloper & ADF Share your impressions on the new JDeveloper 11g Patchset 3 release that came out today! Download it here: http://bit.ly/dogRN8 VikasAatOracle Vikas Anand SOA Suite 11gR1PS3 is Hotpluggable ...see list of features that @Demed posted..#soa #soacommunity   New versions of Oracle Fusion Middleware 11g R1 (11.1.1.4.x)  include: Oracle WebLogic Server 11g R1 (10.3.4) Oracle SOA Suite 11g R1 (11.1.1.4.0) Oracle Business Process Management 11g R1 (11.1.1.4.0) Oracle Complex Event Processing 11g R1 (11.1.1.4.0) Oracle Application Integration Architecture Foundation Pack 11g R1 (11.1.1.4.0) Oracle Service Bus 11g R1 (11.1.1.4.0) Oracle Enterprise Repository 11g R1 (11.1.1.4.0) Oracle Identity Management 11g R1 (11.1.1.4.0) Oracle Enterprise Content Management 11g R1 (11.1.1.4.0) Oracle WebCenter 11g R1 (11.1.1.4.0) - coming soon Oracle Forms, Reports, Portal & Discoverer 11g R1 (11.1.1.4.0) Oracle Repository Creation Utility 11g R1 (11.1.1.4.0) Oracle JDeveloper & Application Development Runtime 11g R1 (11.1.1.4.0) Resources Download  (OTN) Certification Documentation   New Features in Oracle SOA Suite 11g Release 1 (11.1.1.4.0) Updated: January, 2011 Go to Oracle SOA Suite 11g Doc Introduction Oracle SOA Suite 11gR1 (11.1.1.4.0) includes both bug fixes as well as new features listed below - click on the title of each feature for more details. Downloads, documentation links and more information on the Oracle SOA Suite available on the SOA Suite OTN page and as always, we welcome your feedback on the SOA OTN forum. New in Oracle SOA Suite in this release BPEL Component BPEL 2.0 support in JDeveloper The BPEL editor in JDeveloper now generates BPEL 2.0 code and introduces several new activities. Augmented XML variables auto-initialization capabilities The XML variable auto-initialization capabilities have been enhanced to support two need additional use cases: to initialize the to-spec node if it doesn't exist during the rule and to initialize array elements. New Assign Activity dialog The new Assign Activity supports the same drag & drop paradigm used for the XSLT mapper, greatly streamlining the task of assigning multiple variables. Mediator Component Time window parameter for the resequencer This new parameter lets users initiate a best-effort resequencing based on a time window rather than a number of messages. Support for attachments in the Mediator assign dialog The Mediator assign dialog now supports attachment, enabling usage of the Mediator to transmit attachments even if source and target schemas are different. Adapters & Bindings ChunkSize property added to the File Adapter header properties The ChunkSize property of the File Adapter is now available as a header property, allowing in-process modification of the value for this property. Improved support for distributed WLS JMS topics though automatic rebalancing of listeners The JMS Adapter has been enhanced to subscribe to administrative events from WLS JMS. Based on these events, it dynamically rebalances listeners when there are changes to the members of a local or remote WLS JMS distributed destination. JDeveloper configuration wizard for custom JCA adapters A new wizard is available in JDeveloper to configure custom-built adapters Administration & Enterprise Manager Enhanced purging capabilities to manage database growth Historical instance data can now be purged using three different strategies: batch script, scheduled batch script or data partitioning. Asynchronous bulk instance deletion in Enterprise Manager Bulk deletion of instances in Enterprise Manager now executes as an asynchronous operation in Enterprise Manager, returning control to the user as soon as the action has been submitted and acknowledged. B2B Ability to schedule partner downtime This feature allows trading partners to notify each other about planned downtime and to delay delivery of messages during that period. Message sequencing B2B now supports both inbound and outbound message sequencing. Simplified BAM integration with B2B B2B ships with various pre-configured artifacts to simplify monitoring in BAM. Instance Message Java API for B2B The new instance message Java API supports programmatic access to B2B instance message data. Oracle Service Bus (OSB) Certification of the File and FTP JCA Adapters The File and FTP JCA adapters are now certified for use with Oracle Service Bus (in addition to the native transports). Security enhancements Oracle Service Bus now supports SAML 2.0 as well as the OWSM authorization policies. Check the Oracle Service Bus 11.1.1.4 Release Notes for a complete list of new features. Installation, Hot-Pluggability & Certifications Ability to run Oracle SOA Suite on IBM WebSphere Application Server Oracle SOA Suite can now be deployed on IBM WebSphere Application Server Network Deployment (ND) 7.0.11 and IBM WebSphere Application Server 7.0.11. Single JVM developer installation template Oracle SOA Suite can now be targeted to the WebLogic admin server - there is no requirement to also have a managed server. This topology is intended to minimize the memory foorprint of development environments. This is in addition to the list of supported browsers, operating systems and databases already certified in prior releases. Complex Event Processing (CEP) IDE enhancements This release introduces several enhancements to the development IDE, such as adapter wizards and event-type repository. CQL enhancements CQL enhancements include JDBC data cartridges and parametrized queries. Tracing and injecting events in the Event Processing Network (EPN) In the development environment you can now trace and inject events. Check the Oracle CEP 11.1.1.4 Release Notes for a complete list of new features. SOA Suite page on OTN For more information on SOA Specialization and the SOA Partner Community please feel free to register at www.oracle.com/goto/emea/soa (OPN account required) Blog Twitter LinkedIn Mix Forum Wiki Website Technorati Tags: SOA Suite 11.1.1.4,JDeveloper 11.1.1.4,WebLogic 10.3.4,JRockit 10.3.4,SOA Community,Oracle,OPN,SOA,Simone Geib,Guido Schmutz,Edwin Biemond,Lucas Jellema,Simon Haslam,Demed,Vikas Anand,Jürgen Kress

  Read the article

• Cannot join Win7 workstations to Win2k8 domain

  - by wfaulk

  I am trying to connect a Windows 7 Ultimate machine to a Windows 2k8 domain and it's not working. I get this error: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "example.local": The query was for the SRV record for _ldap._tcp.dc._msdcs.example.local The following domain controllers were identified by the query: dc1.example.local dc2.example.local However no domain controllers could be contacted. Common causes of this error include: Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. The client is in an office connected remotely via MPLS to the data center where our domain controllers exist. I don't seem to have anything blocking connectivity to the DCs, but I don't have total control over the MPLS circuit, so it's possible that there's something blocking connectivity. I have tried multiple clients (Win7 Ultimate and WinXP SP3) in the one office and get the same symptoms on all of them. I have no trouble connecting to either of the domain controllers, though I have, admittedly, not tried every possible port. ICMP, LDAP, DNS, and SMB connections all work fine. Client DNS is pointing to the DCs, and "example.local" resolves to the two IP addresses of the DCs. I get this output from the NetLogon Test command line utility: C:\Windows\System32>nltest /dsgetdc:example.local Getting DC name failed: Status = 1355 0x54b ERROR_NO_SUCH_DOMAIN I have also created a separate network to emulate that office's configuration that's connected to the DC network via LAN-to-LAN VPN instead of MPLS. Joining Windows 7 computers from that remote network works fine. The only difference I can find between the two environments is the intermediate connectivity, but I'm out of ideas as to what to test or how to do it. What further steps should I take? (Note that this isn't actually my client workstation and I have no direct access to it; I'm forced to do remote hands access to it, which makes some of the obvious troubleshooting methods, like packet sniffing, more difficult. If I could just set up a system there that I could remote into, I would, but requests to that effect have gone unanswered.) 2011-08-25 update: I had DCDIAG.EXE run on a client attempting to join the domain: C:\Windows\System32>dcdiag /u:example\adminuser /p:********* /s:dc2.example.local Directory Server Diagnosis Performing initial setup: Ldap search capabality attribute search failed on server dc2.example.local, return value = 81 This sounds like it was able to connect via LDAP, but the thing that it was trying to do failed. But I don't quite follow what it was trying to do, much less how to reproduce it or resolve it. 2011-08-26 update: Using LDP.EXE to try and make an LDAP connection directly to the DCs results in these errors: ld = ldap_open("10.0.0.1", 389); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 389); Error <0x51: Fail to connect to 10.0.0.2. ld = ldap_open("10.0.0.1", 3268); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 3268); Error <0x51: Fail to connect to 10.0.0.2. This would seem to point fingers at LDAP connections being blocked somewhere. (And 0x51 == 81, which was the error from DCDIAG.EXE from yesterday's update.) I could swear I tested this using TELNET.EXE weeks ago, but now I'm thinking that I may have assumed that its clearing of the screen was telling me that it was waiting and not that it had connected. I'm tracking down LDAP connectivity problems now. This update may become an answer.

  Read the article

• Openswan ipsec transport tunnel not going up

  - by gparent

  On ClusterA and B I have installed the "openswan" package on Debian Squeeze. ClusterA ip is 172.16.0.107, B is 172.16.0.108 When they ping one another, it does not reach the destination. /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup protostack=netkey oe=off conn L2TP-PSK-CLUSTER type=transport left=172.16.0.107 right=172.16.0.108 auto=start ike=aes128-sha1-modp2048 authby=secret compress=yes /etc/ipsec.secrets: 172.16.0.107 172.16.0.108 : PSK "L2TPKEY" 172.16.0.108 172.16.0.107 : PSK "L2TPKEY" Here is the result of ipsec verify on both machines: root@cluster2:~# ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.28/K2.6.32-5-amd64 (netkey) Checking for IPsec support in kernel [OK] NETKEY detected, testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [FAILED] Checking for 'ip' command [OK] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] root@cluster2:~# This is the end of the output of ipsec auto --status: 000 "cluster": 172.16.0.108<172.16.0.108>[+S=C]...172.16.0.107<172.16.0.107>[+S=C]; prospective erouted; eroute owner: #0 000 "cluster": myip=unset; hisip=unset; 000 "cluster": ike_life: 3600s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cluster": policy: PSK+ENCRYPT+COMPRESS+PFS+UP+IKEv2ALLOW+lKOD+rKOD; prio: 32,32; interface: eth0; 000 "cluster": newest ISAKMP SA: #1; newest IPsec SA: #0; 000 "cluster": IKE algorithm newest: AES_CBC_128-SHA1-MODP2048 000 000 #3: "cluster":500 STATE_QUICK_R0 (expecting QI1); EVENT_CRYPTO_FAILED in 298s; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 #2: "cluster":500 STATE_QUICK_I1 (sent QI1, expecting QR1); EVENT_RETRANSMIT in 13s; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 #1: "cluster":500 STATE_MAIN_I4 (ISAKMP SA established); EVENT_SA_REPLACE in 2991s; newest ISAKMP; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 Interestingly enough, if I do ike-scan on the server here's what happens: Doesn't seem to take my ike settings into account root@cluster1:~# ike-scan -M 172.16.0.108 Starting ike-scan 1.9 with 1 hosts (http://www.nta-monitor.com/tools/ike-scan/) 172.16.0.108 Main Mode Handshake returned HDR=(CKY-R=641bffa66ba717b6) SA=(Enc=3DES Hash=SHA1 Auth=PSK Group=2:modp1024 LifeType=Seconds LifeDuration(4)=0x00007080) VID=4f45517b4f7f6e657a7b4351 VID=afcad71368a1f1c96b8696fc77570100 (Dead Peer Detection v1.0) Ending ike-scan 1.9: 1 hosts scanned in 0.008 seconds (118.19 hosts/sec). 1 returned handshake; 0 returned notify root@cluster1:~# I can't tell what's going on here, this is pretty much the simplest config I can have according to the examples.

  Read the article

• Is it possible to repair a Cisco 3500 XL (3548) switch with POST Error messages?

  - by Alex

  I've got an old Cisco 3500 XL, and it seems to have hardware issues. I've loaded the latest IOS and cleared all config. Does anyone have any experience fixing the switch core? I'm a reasonably competent SMD solderer, can I replace/reflow some chips? I've checked the power supply voltages and it's all within tolerance, and no visible signs of any component damage. Some chips are hot to the touch. I understand that these were EOL as of 2007, but should have a lifetime warranty for the electronics. I don't have a Cisco support contract, so I can't file a ticket. What should I do? Console output: switch: dir flash: Directory of flash:/ 2 -rwx 1811584 <date> c3500xl-c3h2s-mz.120-5.WC17.bin 1799680 bytes available (1812992 bytes used) switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"...################################################################################################################################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC17.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Tue 13-Feb-07 15:04 by antonino Image text-base: 0x00003000, data-base: 0x00352924 Initializing C3500XL flash... flashfs[1]: 1 files, 1 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 3612672 flashfs[1]: Bytes used: 1812992 flashfs[1]: Bytes available: 1799680 flashfs[1]: flashfs fsck took 3 seconds. flashfs[1]: Initialization complete. ...done Initializing C3500XL flash. C3500XL POST: System Board Test: Passed C3500XL POST: Daughter Card Test: Passed C3500XL POST: CPU Buffer Test: Passed C3500XL POST: CPU Notify RAM Test: Passed C3500XL POST: CPU Interface Test: Passed C3500XL POST: Testing Switch Core: Passed Error with Switch Core BIST test Phase 0. Returns: Test Complete Low : 0x0FFFFFFF, Test Complete High : 0xFFFFFFFE Test Phase Low : 0x00000040, Test Phase High : 0x00000000 Test Phase Third : 0x00000000, Test Complete Third : 0x000001F8 C3500XL POST FAILURE: Testing Switch Core: Failed C3500XL POST FAILURE: Testing Buffer Table: Failed C3500XL POST FAILURE: Data Buffer Test: Failed C3500XL POST FAILURE: Configuring Switch Parameters: Failed C3500XL POST FAILURE: Switch Core BIST failed. C3500XL POST FAILURE: Cannot test Modules due to failure of Switch Core POST Del Mar Failure (0th Del Mar): req system failed to init C3500XL POST FAILURE: C3500XL POST FAILURE: ATM: required system failed to init C3500XL POST: Ethernet Controller Test: Passed C3500XL POST FAILURE: MII Test: Failed C3500XL POST FAILURE: Error waiting for Ethernet Controller and SW_PARAMS C3500XL POST FAILURE: Initialization/POST failed C3500XL POST FAILURE: AT: Failing because system POST failed Exception (8192)! Debug Exception (Could be NULL pointer dereference) CPU Register Context: Vector = 0x00002000 PC = 0x000F36F4 MSR = 0x00029200 CR = 0x22000024 LR = 0x000F6964 CTR = 0x001DE46C XER = 0x00000000 R0 = 0x00000000 R1 = 0x004E2580 R2 = 0x00000000 R3 = 0x00000000 R4 = 0x00000001 R5 = 0x00000000 R6 = 0x004E2718 R7 = 0x004E2718 R8 = 0x00000008 R9 = 0x00000000 R10 = 0x0000FFFF R11 = 0x00480000 R12 = 0x42000024 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000 R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000 R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000 R24 = 0x00000000 R25 = 0x00000020 R26 = 0x004E2718 R27 = 0x004E2718 R28 = 0x00000020 R29 = 0x00002513 R30 = 0x00000001 R31 = 0x00000000 Stack trace: PC = 0x000F36F4, SP = 0x004E2580 Frame 00: SP = 0x004E25A0 PC = 0x40000016 Frame 01: SP = 0x004E2618 PC = 0x000F6964 Frame 02: SP = 0x004E26A8 PC = 0x000F76DC Frame 03: SP = 0x004E26C8 PC = 0x000E8114 Frame 04: SP = 0x004E26F0 PC = 0x001F5BF8 Frame 05: SP = 0x004E2710 PC = 0x001F5CF4 Frame 06: SP = 0x004E2748 PC = 0x0023F4DC Frame 07: SP = 0x004E2750 PC = 0x0023E650 Frame 08: SP = 0x004E27C8 PC = 0x0023E89C Frame 09: SP = 0x004E27E0 PC = 0x0028AF34 Frame 10: SP = 0x004E27E8 PC = 0x001E38F8 Frame 11: SP = 0x004E2808 PC = 0x001E39A8 Frame 12: SP = 0x004E2820 PC = 0x0014E220 Frame 13: SP = 0x004E28C8 PC = 0x0014E39C Frame 14: SP = 0x00000000 PC = 0x001EB510

  Read the article

• DNS lookups failing somewhere between firewall and router

  - by TessellatingHeckler

  we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

  Read the article

• Get Information to Your Blog with Microsoft Broadcaster

  - by Matthew Guay

  Do you often have people ask you for advice about technology, or do you write tech-focused blog or newsletter?  Here’s how you can get information to share with your readers about Microsoft technology with Microsoft Broadcaster. Microsoft Broadcaster is a new service from Microsoft to help publishers, bloggers, developers, and other IT professionals find relevant information and resources from Microsoft.  You can use it to help discover things to write about, or simply discover new information about the technology you use.  Broadcaster will also notify you when new resources are available about the topics that interest you.  Let’s look at how you could use this to expand your blog and help your users. Getting Started Head over to the Microsoft Broadcaster site (link below), and click Join to get started. Sign in with your Windows Live ID, or create a new account if you don’t already have one. Near the bottom of the page, add information about your blog, newsletter, or group that you want to share Broadcaster information with.  Click Add when you’re done entering information.  You can enter as many sites or groups as you wish. When you’ve entered all of your information, click the Apply button at the bottom of the page.  Broadcaster will then let you know your information has been submitted, but you’ll need to wait several days to see if you are approved or not. Our application was approved about 2 days after applying, though this may vary.  When you’re approved, you’ll receive an email letting you know.  Return to the Broadcaster website (link below), but this time, click Sign in. Accept the terms of use by clicking I Accept at the bottom of the page. Confirm that your information entered previously is correct, and then click Configure my keywords at the bottom of the page. Now you can pick the topics you want to stay informed about.  Type keywords in the textbox, and it will bring up relevant topics with IntelliSense. Here we’ve added several topics to keep up with. Next select the Microsoft Products you want to keep track of.  If the product you want to keep track of is not listed, make sure to list it in the keywords section as above. Finally, select the types of content you wish to see, including articles, eBooks, webcasts, and more. Finally, when everything’s entered, click Configure My Alerts at the bottom of the page. Broadcaster can automatically email you when new content is found.  If you would like this, click Subscribe.  Otherwise, simply click Access Dashboard to go ahead and find your personalized content. If you choose to receive emails of new content, you’ll have to configure it with Windows Live Alerts.  Click Continue to set this up. Select if you want to receive Messenger alerts, emails, and/or text messages when new content is available.  Click Save when you’re finished. Finally, select how often you want to be notified, and then click Access Dashboard to view the content currently available. Finding Content For Your Blog, Site, or Group Now you can find content specified for your interests from the dashboard.  To access the dashboard in the future, simply go to the Broadcaster site and click Sign In. Here you can see available content, and can search for different topics or customize the topics shown. You’ll see snippets of information from various Microsoft videos, articles, whitepapers, eBooks, and more, depending on your settings.  Click the link at the top of the snippet to view the content, or right-click and copy the link to use in emails or on social networks like Twitter. If you’d like to add this snippet to your website or blog, click the Download content link at the bottom.   Now you can preview what the snippet will look like on your site, and change the width or height to fit your site.  You can view and edit the source code of the snippet from the box at the bottom, and then copy it to use on your site. Copy the code, and paste it in the HTML of a blog post, email, webpage, or anywhere else you wish to share it.  Here we’re pasting it into the HTML editor in Windows Live Writer so we can post it to a blog. After adding a title and opening paragraph, we have a nice blog post that only took a few minutes to put together but should still be useful for our readers.  You can check out the blog post we created at the link below. Readers can click on the links, which will direct them to the content on Microsoft’s websites. Conclusion If you frequently need to find educational and informative content about Microsoft products and services, Broadcaster can be a great service to keep you up to date.  The service worked quite good in our tests, and generally found relevant content to our keywords.  We had difficulty embedding links to eBooks that were listed by Broadcaster, but everything else worked for us.  Now you can always have high quality content to help your customers, coworkers, friends, and more, and you just might find something that will help you, too! Link Microsoft Broadcaster (registration required) Example Post at Techinch.com with Content from Microsoft Broadcaster Similar Articles Productive Geek Tips Create An Electronic Business Card In Outlook 2007Mysticgeek Blog: A Look at Internet Explorer 8 Beta 1 on Windows XPAnnouncing the How-To Geek BlogsNew Vista Syntax for Opening Control Panel Items from the Command-lineHow To Create and Publish Blog Posts in Word 2010 & 2007 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Fix Common Inkjet Printer Errors Dual Boot Ubuntu and Windows 7 What is HTML5? Default Programs Editor – One great tool for Setting Defaults Convert BMP, TIFF, PCX to Vector files with RasterVect Free Identify Fonts using WhatFontis.com

  Read the article

• cherrypy fails to stop when puppet tries to ensure running and refresh it at the same time

  - by ento

  I am trying to manage a cherrypy service with puppet. However, when the configuration is applied, cherryd ends up with no PID file although the process is up and running. Since the PID file is lost I can no longer stop the process with /etc/init.d/mycherryd stop (unless I modify the handmade init script to lookup the PID with ps or something.) $ /etc/init.d/mycherryd status cherryd dead but subsys locked The problem seems to be that puppet is trying to refresh/restart cherryd (triggered by changes in configuration files) immediately after ensuring it's running (as specified in the manifest), and cherrypy fails to stop and start (restart) itself while still executing its startup process. Is there a clear cut solution to this problem? Is this a bug on the cherrypy side, or can I write a puppet manifest so refresh is called only after the service is up and running? Any suggestion welcome. cherrypy log See how cherrypy catches SIGTERM midway through startup and still starts to listen. :cherrypy.error[18666] 2010-02-12 13:10:23,551 INFO: ENGINE Listening for SIGHUP. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Listening for SIGTERM. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Listening for SIGUSR1. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Bus STARTING :cherrypy.error[18671] 2010-02-12 13:10:23,554 INFO: ENGINE Daemonized to PID: 18671 :cherrypy.error[18671] 2010-02-12 13:10:23,554 INFO: ENGINE PID 18671 written to '/var/mycherryd/cherry.pid'. :cherrypy.error[18671] 2010-02-12 13:10:23,555 INFO: ENGINE Started monitor thread '_TimeoutMonitor'. :cherrypy.error[18670] 2010-02-12 13:10:23,556 INFO: ENGINE Forking twice. :cherrypy.error[18666] 2010-02-12 13:10:23,557 INFO: ENGINE Forking once. :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE Caught signal SIGTERM. :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE Bus STOPPING :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE HTTP Server cherrypy._cpwsgi_server.CPWSGIServer(('0.0.0.0', 12380)) already shut down :cherrypy.error[18671] 2010-02-12 13:10:23,717 INFO: ENGINE Stopped thread '_TimeoutMonitor'. :cherrypy.error[18671] 2010-02-12 13:10:23,717 INFO: ENGINE Bus STOPPED :cherrypy.error[18671] 2010-02-12 13:10:23,732 INFO: ENGINE Bus EXITING :cherrypy.error[18671] 2010-02-12 13:10:23,759 INFO: ENGINE PID file removed: '/var/mycherryd/cherry.pid'. :cherrypy.error[18671] 2010-02-12 13:10:23,782 INFO: ENGINE Bus EXITED :cherrypy.error[18671] 2010-02-12 13:10:23,792 INFO: ENGINE Serving on 0.0.0.0:12380 :cherrypy.error[18671] 2010-02-12 13:10:23,826 INFO: ENGINE Bus STARTED puppet log puppet tries to refresh the service immediately after ensuring it to be 'running'. Feb 12 13:10:22 localhost puppetd[8159]: (//mycherrypy/File[conffiles]) Scheduling refresh of Service[cherryd] Feb 12 13:10:22 localhost last message repeated 12 times Feb 12 13:10:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]/ensure) ensure changed 'stopped' to 'running' Feb 12 13:10:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]) Triggering 'refresh' from 13 dependencies Feb 12 13:11:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]) Failed to call refresh on Service[mycherryd]: Could not stop Service[mycherryd]: Execution of '/sbin/service mycherryd stop' returned 1: at /etc/puppet/manifests/mycherrypy.pp:161 Feb 12 13:11:24 localhost puppetd[8159]: Value of 'preferred_serialization_format' (pson) is invalid for report, using default (marshal) Feb 12 13:11:24 localhost puppetd[8159]: Finished catalog run in 99.25 seconds puppet manifest excerpt class mycherrypy { file { 'rpm': path => "/tmp/${apiserver}.i386.rpm", source => "${fileserver}/${apiserver}.i386.rpm"; 'conffiles': require => Package["${apiserver}"], path => "${service_home}/config/", ensure => present, source => "${fileserver}/config/", notify => Service["mycherryd"]; } package { "$apiserver": provider => 'rpm', source => "/tmp/${apiserver}.i386.rpm", ensure => latest; } service { "mycherryd": require => [File["conffiles"], Package["${apiserver}"]], ensure => running, provider => redhat, hasstatus => true; } }

  Read the article

• cherrypy fails to stop when puppet tries to ensure running and refresh it at the same time

  - by ento

  I am trying to manage a cherrypy service with puppet. However, when the configuration is applied, cherryd ends up with no PID file although the process is up and running. Since the PID file is lost I can no longer stop the process with /etc/init.d/mycherryd stop (unless I modify the handmade init script to lookup the PID with ps or something.) $ /etc/init.d/mycherryd status cherryd dead but subsys locked The problem seems to be that puppet is trying to refresh/restart cherryd (triggered by changes in configuration files) immediately after ensuring it's running (as specified in the manifest), and cherrypy fails to stop and start (restart) itself while still executing its startup process. Is there a clear cut solution to this problem? Is this a bug on the cherrypy side, or can I write a puppet manifest so refresh is called only after the service is up and running? Any suggestion welcome. cherrypy log See how cherrypy catches SIGTERM midway through startup and still starts to listen. :cherrypy.error[18666] 2010-02-12 13:10:23,551 INFO: ENGINE Listening for SIGHUP. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Listening for SIGTERM. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Listening for SIGUSR1. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Bus STARTING :cherrypy.error[18671] 2010-02-12 13:10:23,554 INFO: ENGINE Daemonized to PID: 18671 :cherrypy.error[18671] 2010-02-12 13:10:23,554 INFO: ENGINE PID 18671 written to '/var/mycherryd/cherry.pid'. :cherrypy.error[18671] 2010-02-12 13:10:23,555 INFO: ENGINE Started monitor thread '_TimeoutMonitor'. :cherrypy.error[18670] 2010-02-12 13:10:23,556 INFO: ENGINE Forking twice. :cherrypy.error[18666] 2010-02-12 13:10:23,557 INFO: ENGINE Forking once. :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE Caught signal SIGTERM. :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE Bus STOPPING :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE HTTP Server cherrypy._cpwsgi_server.CPWSGIServer(('0.0.0.0', 12380)) already shut down :cherrypy.error[18671] 2010-02-12 13:10:23,717 INFO: ENGINE Stopped thread '_TimeoutMonitor'. :cherrypy.error[18671] 2010-02-12 13:10:23,717 INFO: ENGINE Bus STOPPED :cherrypy.error[18671] 2010-02-12 13:10:23,732 INFO: ENGINE Bus EXITING :cherrypy.error[18671] 2010-02-12 13:10:23,759 INFO: ENGINE PID file removed: '/var/mycherryd/cherry.pid'. :cherrypy.error[18671] 2010-02-12 13:10:23,782 INFO: ENGINE Bus EXITED :cherrypy.error[18671] 2010-02-12 13:10:23,792 INFO: ENGINE Serving on 0.0.0.0:12380 :cherrypy.error[18671] 2010-02-12 13:10:23,826 INFO: ENGINE Bus STARTED puppet log puppet tries to refresh the service immediately after ensuring it to be 'running'. Feb 12 13:10:22 localhost puppetd[8159]: (//mycherrypy/File[conffiles]) Scheduling refresh of Service[cherryd] Feb 12 13:10:22 localhost last message repeated 12 times Feb 12 13:10:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]/ensure) ensure changed 'stopped' to 'running' Feb 12 13:10:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]) Triggering 'refresh' from 13 dependencies Feb 12 13:11:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]) Failed to call refresh on Service[mycherryd]: Could not stop Service[mycherryd]: Execution of '/sbin/service mycherryd stop' returned 1: at /etc/puppet/manifests/mycherrypy.pp:161 Feb 12 13:11:24 localhost puppetd[8159]: Value of 'preferred_serialization_format' (pson) is invalid for report, using default (marshal) Feb 12 13:11:24 localhost puppetd[8159]: Finished catalog run in 99.25 seconds puppet manifest excerpt class mycherrypy { file { 'rpm': path => "/tmp/${apiserver}.i386.rpm", source => "${fileserver}/${apiserver}.i386.rpm"; 'conffiles': require => Package["${apiserver}"], path => "${service_home}/config/", ensure => present, source => "${fileserver}/config/", notify => Service["mycherryd"]; } package { "$apiserver": provider => 'rpm', source => "/tmp/${apiserver}.i386.rpm", ensure => latest; } service { "mycherryd": require => [File["conffiles"], Package["${apiserver}"]], ensure => running, provider => redhat, hasstatus => true; } }

  Read the article

• Answers to Your Common Oracle Database Lifecycle Management Questions

  - by Scott McNeil

  We recently ran a live webcast on Strategies for Managing Oracle Database's Lifecycle. There were tons of questions from our audience that we simply could not get to during the hour long presentation. Below are some of those questions along with their answers. Enjoy! Question: In the webcast the presenter talked about “gold” configuration standards, for those who want to use this technique, could you recommend a best practice to consider or follow? How do I get started? Answer:Gold configuration standardization is a quick and easy way to improve availability through consistency. Start by choosing a reference database and saving the configuration to the Oracle Enterprise Manager repository using the Save Configuration feature. Next create a comparison template using the Oracle provided template as a starting point and modify the ignored properties to eliminate expected differences in your environment. Finally create a comparison specification using the comparison template you created plus your saved gold configuration and schedule it to run on a regular basis. Don’t forget to fill in the email addresses of those you want to notify upon drift detection. Watch the database configuration management demo to learn more. Question: Can Oracle Lifecycle Management Pack for Database help with patching an Oracle Real Application Cluster (RAC) environment? Answer: Yes, Oracle Enterprise Manager supports both parallel and rolling patch application of Oracle Real Application Clusters. The use of rolling patching is recommended as there is no downtime involved. For more details watch this demo. Question: What are some of the things administrators can do to control configuration drift? Why is it important? Answer:Configuration drift is one of the main causes of instability and downtime of applications. Oracle Enterprise Manager makes it easy to manage and control drift using scheduled configuration comparisons combined with comparison templates. Question: Does Oracle Enterprise Manager 12c Release 2 offer an incremental update feature for "gold" images? For instance, if the source binary has a higher PSU level, what is the best approach to update the existing "gold" image in the software library? Do you have to create a new image or can you just update the original one? Answer:Provisioning Profiles (Gold images) can contain the installation files and database configuration templates. Although it is possible to make some changes to the profile after creation (mainly to configuration), it is normally recommended to simply create a new profile after applying a patch to your reference database. Question: The webcast talked about enforcing in-house standards, does Oracle Enterprise Manager 12c offer verification of your databases and systems to those standards? For example, the initial "gold" image has been massively deployed over time, and there may be some changes to it. How can you do regular checks from Enterprise Manager to ensure the in-house standards are being enforced? Answer:There are really two methods to validate conformity to standards. The first method is to use gold standards which you compare other databases to report unwanted differences. This method uses a new comparison template technology which allows users to ignore known differences (i.e. SID, Start time, etc) which results in a report only showing important or non-conformant differences. This method is quick to setup and configure and recommended for those who want to get started validating compliance quickly. The second method leverages the new compliance framework which allows the creation of specific and robust validations. These compliance rules are grouped into standards which can be assigned to databases quickly and easily. Compliance rules allow for targeted and more sophisticated validation beyond the basic equals operation available in the comparison method. The compliance framework can be used to implement just about any internal or industry standard. The compliance results will track current and historic compliance scores at the overall and individual database targets. When the issue is resolved, the score is automatically affected. Compliance framework is the recommended long term solution for validating compliance using Oracle Enterprise Manager 12c. Check out this demo on database compliance to learn more. Question: If you are using the integration between Oracle Enterprise Manager and My Oracle Support in an "offline" mode, how do you know if you have the latest My Oracle Support metadata? Answer:In Oracle Enterprise Manager 12c Release 2, you now only need to download one zip file containing all of the metadata xmls files. There is no indication that the metadata has changed but you could run a checksum on the file and compare it to the previously downloaded version to see if it has changed. Question: What happens if a patch fails while administrators are applying it to a database or system? Answer:A large portion of Oracle Enterprise Manager's patch automation is the pre-requisite checks that happen to ensure the highest level of confidence the patch will successfully apply. It is recommended you test the patch in a non-production environment and save the patch plan as a template once successful so you can create new plans using the saved template. If you are using the recommended ‘out of place’ patching methodology, there is no urgency because the database is still running as the cloned Oracle home is being patched. Users can address the issue and restart the patch procedure at the point it left off. If you are using 'in place' method, you can address the issue and continue where the procedure left off. Question: Can Oracle Enterprise Manager 12c R2 compare configurations between more than one target at the same time? Answer:Oracle Enterprise Manager 12c can compare any number of target configurations at one time. This is the basis of many important use cases including Configuration Drift Management. These comparisons can also be scheduled on a regular basis and emails notification sent should any differences appear. To learn more about configuration search and compare watch this demo. Question: How is data comparison done since changes are taking place in a live production system? Answer:There are many things to keep in mind when using the data comparison feature (as part of the Change Management ability to compare table data). It was primarily intended to be used for maintaining consistency of important but relatively static data. For example, application seed data and application setup configuration. This data does not change often but is critical when testing an application to ensure results are consistent with production. It is not recommended to use data comparison on highly dynamic data like transactional tables or very large tables. Question: Which versions of Oracle Database can be monitored through Oracle Enterprise Manager 12c? Answer:Oracle Database versions: 9.2.0.8, 10.1.0.5, 10.2.0.4, 10.2.0.5, 11.1.0.7, 11.2.0.1, 11.2.0.2, 11.2.0.3. Watch the On-Demand Webcast Stay Connected: Twitter | Facebook | YouTube | Linkedin | NewsletterDownload the Oracle Enterprise Manager Cloud Control12c Mobile app

  Read the article

• SQL Sentry First Impressions

  - by AjarnMark

  After struggling to defend my SQL Servers from a political attack recently, I realized that I needed better tools to back me up, and SQL Sentry is the leading candidate. A couple of weeks ago, seemingly from out of nowhere, complaints from the business users started coming in that one of the core internal applications was running dramatically slower than normal, and fingers were being pointed at the SQL Server.  Unfortunately, we don’t have a production DBA whose entire job is to monitor and maintain our SQL Servers.  The responsibility falls to me to do the best I can, investing only a small portion of my time, because there are so many other responsibilities to take care of, and our industry is still deep in recession.  I inherited these SQL Servers and have made significant improvements in process and procedure, but I had not yet made the time to take real baseline measurements or keep a really close eye on the performance.  Like many DBAs, I wrote several of my own tools and used the “built-in tools” like Profiler, PerfMon, and sp_who2 (did I mention most of our instances are SQL Server 2000?).  These have all served me well for in-the-moment troubleshooting and maintenance, but they really fell down on the job when I was called upon to “prove” that SQL Server performance was acceptable and more importantly had not degraded recently (i.e. historical comparisons).  I really didn’t have anything from a historical comparison perspective, but I was able to show that current performance was acceptable, and deflect attention back onto other components (which in fact turned out to be the real culprit). That experience dramatically illustrated the need for better monitoring tools.  Coincidentally, I had been talking recently to my boss about the mini nightmare of monitoring several critical and interdependent overnight jobs that operate on separate instances of SQL Server.  Among other tools, I had been using Idera’s SQL Job Manager which is a free tool and did a nice job of showing me job schedules and histories in a nice calendar view.  This worked fairly well, and for the money (did I mention it was free?) it couldn’t be beat.  But it is based on the stored job history in MSDB, and there were other performance problems that we ran into when we started changing the settings for how much job history to retain, in order to be able to look back a month or more in the calendar view.  Another coincidence (if you believe in such things) was that when we had some of those performance challenges, I posted a couple of questions to the #sqlhelp hashtag on Twitter and Greg Gonzalez (@SQLSensei) suggested I check out SQL Sentry’s Event Manager.  At the time, I just thought he worked there, but later found out that he founded the company.  When I took a quick look at the features & benefits, the one that really jumped out at me is Chaining and Queueing which sounded like it would really help with our “interdependent jobs on different servers” issue. I know that is a lot of background story and coincidences, but hopefully you have stuck with me so far, and now we have arrived at the point where last week I downloaded and installed the 30-day trial of the SQL Sentry Power Suite, which is Event Manager plus Performance Advisor.  And I must say that I really like what I see so far.  Here are a few highlights: Great Support.  I had two issues getting the trial setup and monitoring a handful of our servers.  One of which was entirely my fault (missed a security setting in SQL 2008) and the other was mostly my fault (late change to some config settings that were apparently cached and did not get refreshed properly).  In both cases, the support staff at SQL Sentry were very responsive and rather quickly figured out what the cause and fix was for each of them.  This left me with a great impression of the company.  Kudos to them! Chaining and Queueing.  While I have not yet activated this feature, I am very excited about the possibilities.  We have jobs on three different instances of SQL Server that have to be run in a certain order, and each has to finish before the next can successfully begin, and I believe this feature will ensure just that.  It has been a real pain in the backside when one of those jobs runs just a little too long and does not finish before the job on another instance starts, thus triggering a chain reaction of either outright job failures, or worse, successful completion of completely invalid processing. Calendar View.  I really, really like the Event Manager calendar view where I can see all jobs and events across all instances and identify potential resource contention as well as windows of opportunity for maintenance activity.  Very well done, and based on Event Manager’s own database of accumulated historical information rather than querying the source instances every time. Performance Advisor Dashboard History View.  This view let’s me quickly select a date and time range and it displays graphs of key SQL Server and Windows metrics.  This is exactly the thing I needed to answer the “has performance changed recently” question at the beginning of this post. Reporting Services Subscription Jobs with Report Name.  This was a big and VERY pleasant surprise.  If you have ever looked at the list of SQL Server jobs that SQL Server Reporting Services creates when you make a Subscription, you will notice that they all have some sort of GUID as the name of the job.  This is really ugly, and really annoying because when you are just looking at the SQL Agent and Job Activity Monitor, if you see that Job X failed, you really do not have any indication in the name or the properties of the Job itself, as to what Report that was for.  But with SQL Sentry Event Manager you do.  The Jobs list in the Navigator pane in SQL Sentry, amazingly, displays the name of the Report that the Subscription Job is for.  And when you open it to see more details, it shows you the full Reporting Services path to that Report, so you can immediately track it down in the Report Manager in case you want to identify/notify the owner or edit the Subscription information.  I did not expect this at all, but I sure do like it.  HOORAY! That is just my first impressions from using the tools for a few days.  And I haven’t even gotten into how it showed me where I was completely mistaken about one aspect of my SQL Server disk configurations.  I’ll share that lesson in another blog entry.  But I have to say it again, the combination of Event Manager and Performance Advisor working together have really made me a fan.

  Read the article

• Why you need to learn async in .NET

  - by PSteele

  I had an opportunity to teach a quick class yesterday about what’s new in .NET 4.0.  One of the topics was the TPL (Task Parallel Library) and how it can make async programming easier.  I also stressed that this is the direction Microsoft is going with for C# 5.0 and learning the TPL will greatly benefit their understanding of the new async stuff.  We had a little time left over and I was able to show some code that uses the Async CTP to accomplish some stuff, but it wasn’t a simple demo that you could jump in to and understand so I thought I’d thrown one together and put it in a blog post. The entire solution file with all of the sample projects is located here. A Simple Example Let’s start with a super-simple example (WindowsApplication01 in the solution). I’ve got a form that displays a label and a button.  When the user clicks the button, I want to start displaying the current time for 15 seconds and then stop. What I’d like to write is this: lblTime.ForeColor = Color.Red; for (var x = 0; x < 15; x++) { lblTime.Text = DateTime.Now.ToString("HH:mm:ss"); Thread.Sleep(1000); } lblTime.ForeColor = SystemColors.ControlText; (Note that I also changed the label’s color while counting – not quite an ILM-level effect, but it adds something to the demo!) As I’m sure most of my readers are aware, you can’t write WinForms code this way.  WinForms apps, by default, only have one thread running and it’s main job is to process messages from the windows message pump (for a more thorough explanation, see my Visual Studio Magazine article on multithreading in WinForms).  If you put a Thread.Sleep in the middle of that code, your UI will be locked up and unresponsive for those 15 seconds.  Not a good UX and something that needs to be fixed.  Sure, I could throw an “Application.DoEvents()” in there, but that’s hacky. The Windows Timer Then I think, “I can solve that.  I’ll use the Windows Timer to handle the timing in the background and simply notify me when the time has changed”.  Let’s see how I could accomplish this with a Windows timer (WindowsApplication02 in the solution): public partial class Form1 : Form { private readonly Timer clockTimer; private int counter;   public Form1() { InitializeComponent(); clockTimer = new Timer {Interval = 1000}; clockTimer.Tick += UpdateLabel; }   private void UpdateLabel(object sender, EventArgs e) { lblTime.Text = DateTime.Now.ToString("HH:mm:ss"); counter++; if (counter == 15) { clockTimer.Enabled = false; lblTime.ForeColor = SystemColors.ControlText; } }   private void cmdStart_Click(object sender, EventArgs e) { lblTime.ForeColor = Color.Red; counter = 0; clockTimer.Start(); } } Holy cow – things got pretty complicated here.  I use the timer to fire off a Tick event every second.  Inside there, I can update the label.  Granted, I can’t use a simple for/loop and have to maintain a global counter for the number of iterations.  And my “end” code (when the loop is finished) is now buried inside the bottom of the Tick event (inside an “if” statement).  I do, however, get a responsive application that doesn’t hang or stop repainting while the 15 seconds are ticking away. But doesn’t .NET have something that makes background processing easier? The BackgroundWorker Next I try .NET’s BackgroundWorker component – it’s specifically designed to do processing in a background thread (leaving the UI thread free to process the windows message pump) and allows updates to be performed on the main UI thread (WindowsApplication03 in the solution): public partial class Form1 : Form { private readonly BackgroundWorker worker;   public Form1() { InitializeComponent(); worker = new BackgroundWorker {WorkerReportsProgress = true}; worker.DoWork += StartUpdating; worker.ProgressChanged += UpdateLabel; worker.RunWorkerCompleted += ResetLabelColor; }   private void StartUpdating(object sender, DoWorkEventArgs e) { var workerObject = (BackgroundWorker) sender; for (int x = 0; x < 15; x++) { workerObject.ReportProgress(0); Thread.Sleep(1000); } }   private void UpdateLabel(object sender, ProgressChangedEventArgs e) { lblTime.Text = DateTime.Now.ToString("HH:mm:ss"); }   private void ResetLabelColor(object sender, RunWorkerCompletedEventArgs e) { lblTime.ForeColor = SystemColors.ControlText; }   private void cmdStart_Click(object sender, EventArgs e) { lblTime.ForeColor = Color.Red; worker.RunWorkerAsync(); } } Well, this got a little better (I think).  At least I now have my simple for/next loop back.  Unfortunately, I’m still dealing with event handlers spread throughout my code to co-ordinate all of this stuff in the right order. Time to look into the future. The async way Using the Async CTP, I can go back to much simpler code (WindowsApplication04 in the solution): private async void cmdStart_Click(object sender, EventArgs e) { lblTime.ForeColor = Color.Red; for (var x = 0; x < 15; x++) { lblTime.Text = DateTime.Now.ToString("HH:mm:ss"); await TaskEx.Delay(1000); } lblTime.ForeColor = SystemColors.ControlText; } This code will run just like the Timer or BackgroundWorker versions – fully responsive during the updates – yet is way easier to implement.  In fact, it’s almost a line-for-line copy of the original version of this code.  All of the async plumbing is handled by the compiler and the framework.  My code goes back to representing the “what” of what I want to do, not the “how”. I urge you to download the Async CTP.  All you need is .NET 4.0 and Visual Studio 2010 sp1 – no need to set up a virtual machine with the VS2011 beta (unless, of course, you want to dive right in to the C# 5.0 stuff!).  Starting playing around with this today and see how much easier it will be in the future to write async-enabled applications.

  Read the article

• Too many Bind query (cache) denied, DNS attack?

  - by Jake

  Once Bind crashed and I did: tail -f /var/log/messages I see a massive number of logs every second. Is this a DNS attack? or is there something wrong? Sometimes I see a domain in logs like this: dOmAin.com (upper and lower). As you see there is only one single domain in the logs with different IPs Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#38921: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.144.171#38833: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.17#42428: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.27#37899: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#39263: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.170#59723: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#32903: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 134.58.60.1#47558: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.34#47387: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.8#59392: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.19#64395: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 217.72.163.3#42190: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 83.146.21.252#22020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.116#57342: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#52020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.72#64317: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#31989: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#47436: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.16#44005: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#50379: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 94.241.128.3#60106: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#59118: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 212.95.135.78#27811: query (cache) 'domain.com/A/IN' denied /etc/resolv.conf ; generated by /sbin/dhclient-script nameserver 4.2.2.4 nameserver 8.8.4.4 Bind config: // generated by named-bootconf.pl options { directory "/var/named"; /* * If there is a firewall between you and nameservers you want * to talk to, you might need to uncomment the query-source * directive below. Previous versions of BIND always asked * questions using port 53, but BIND 8.1 uses an unprivileged * port by default. */ // query-source address * port 53; allow-transfer { none; }; allow-recursion { localnets; }; //listen-on-v6 { any; }; notify no; }; // // a caching only nameserver config // controls { inet 127.0.0.1 allow { localhost; } keys { rndckey; }; }; zone "." IN { type hint; file "named.ca"; }; zone "localhost" IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "named.local"; allow-update { none; }; };

  Read the article

• Key Promoter for NetBeans

  - by Geertjan

  Whenever a menu item or toolbar button is clicked, it would be handy if NetBeans were to tell you 'hey, did you know, you can actually do this via the following keyboard shortcut', if a keyboard shortcut exists for the invoked action. After all, ultimately, a lot of developers would like to do everything with the keyboard and a key promoter feature of this kind is a helpful tool in learning the keyboard shortcuts related to the menu items and toolbar buttons you're clicking with your mouse. Above, you see the balloon message that appears for each menu item and toolbar button that you click and, below, you can see a list of all the actions that have been logged in the Notifications window. That happens automatically when an action is invoked (assuming the plugin described in this blog entry is installed), showing the display name of the action, together with the keyboard shortcut, which is presented as a hyperlink which, when clicked, re-invokes the action (which might not always be relevant, especially for context-sensitive actions, though for others it is quite useful, e.g., reopen the New Project wizard). And here's all the code. Notice that I'm hooking into the 'uigestures' functionality, which was suggested by Tim Boudreau, and I have added my own handler, which was suggested by Jaroslav Tulach, which gets a specific parameter from each new log entry handled by the 'org.netbeans.ui.actions' logger, makes sure that the parameter actually is an action, and then gets the relevant info from the action, if the relevant info exists: @OnShowingpublic class Startable implements Runnable {    @Override    public void run() {        Logger logger = Logger.getLogger("org.netbeans.ui.actions");        logger.addHandler(new StreamHandler() {            @Override            public void publish(LogRecord record) {                Object[] parameters = record.getParameters();                if (parameters[2] instanceof Action) {                    Action a = (Action) parameters[2];                    JMenuItem menu = new JMenuItem();                    Mnemonics.setLocalizedText(                            menu,                             a.getValue(Action.NAME).toString());                    String name = menu.getText();                    if (a.getValue(Action.ACCELERATOR_KEY) != null) {                        String accelerator = a.getValue(Action.ACCELERATOR_KEY).toString();                        NotificationDisplayer.getDefault().notify(                                name,                                 new ImageIcon("/org/nb/kp/car.png"),                                 accelerator,                                 new ActionListener() {                            @Override                            public void actionPerformed(ActionEvent e) {                                a.actionPerformed(e);                            }                        });                    }                }            }        });    }} Indeed, inspired by the Key Promoter in IntelliJ IDEA. Interested in trying it out? If there's interest in it, I'll put it in the NetBeans Plugin Portal.

  Read the article

• Sonicwall VPN, Domain Controller Issues

  - by durilai

  I am trying to get the domain logon script to execute when I connect to VPN. I have a SonicWall 4060PRO, with the SonicOS Enhanced 4.2.0.0-10e. The VPN connects successfully, but the script does not execute. I am posting the log below, but I see two issues. The first is the inability to connect to domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. The second is the failure of the script. 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found.. I assume the second issue is caused because of the first, also on the second issue it seems to be trying to get the logon script from my local PC, not the server. Finally, the DC can be pinged and reached by its computer name once the VPN is connected. The shares that the script is tring to map can be mapped manually. Any help is appreciated. 2009/12/18 19:49:31:063 Information The connection "GroupVPN_0006B1030980" has been enabled. 2009/12/18 19:49:32:223 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX XAuth has requested a username but one has not yet been specified. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Sending phase 1 delete. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX User authentication information is needed to complete the connection. 2009/12/18 19:49:32:393 Information An incoming ISAKMP packet from XXX.XXX.XXX.XXX was ignored. 2009/12/18 19:49:36:962 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:37:094 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:37:100 Information XXX.XXX.XXX.XXX Sending XAuth reply. 2009/12/18 19:49:37:110 Information XXX.XXX.XXX.XXX Received initial contact notify. 2009/12/18 19:49:37:153 Information XXX.XXX.XXX.XXX Received XAuth status. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX Sending XAuth acknowledgement. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX User authentication has succeeded. 2009/12/18 19:49:37:247 Information XXX.XXX.XXX.XXX Received request for policy version. 2009/12/18 19:49:37:253 Information XXX.XXX.XXX.XXX Sending policy version reply. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Received policy change is not required. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Sending policy acknowledgement. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX The configuration for the connection is up to date. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 2 negotiation with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting quick mode phase 2 exchange. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX The SA lifetime for phase 2 is 28800 seconds. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX Phase 2 with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP has completed. 2009/12/18 19:49:37:896 Information Renewing IP address for the virtual interface (00-60-73-4C-3F-45). 2009/12/18 19:49:40:189 Information The virtual interface has been added to the system with IP address 10.10.10.112. 2009/12/18 19:49:40:319 Information The system ARP cache has been flushed. 2009/12/18 19:49:40:576 Information XXX.XXX.XXX.XXX NetWkstaUserGetInfo returned: user: Dustin, logon domain: DT-WIN7, logon server: DT-WIN7 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX calling NetUserGetInfo: Server: , User: Dustin, level: 3 2009/12/18 19:49:53:460 Information XXX.XXX.XXX.XXX NetUserGetInfo returned: home dir: , remote dir: , logon script: 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found..

  Read the article

• Mozilla Weave can't sync Firefox. What's wrong?

  - by Mehper C. Palavuzlar

  For the last few days, Mozilla Weave can't sync. Below is the activity log. Any ideas? 2010-05-02 20:47:15 Service.Main WARN Unknown error while downloading metadata record. Aborting sync. 2010-05-02 20:47:15 Service.Main CONFIG Starting backoff, next sync at:Sun May 02 2010 21:16:09 GMT+0300 (GTB Yaz Saati) 2010-05-02 20:47:15 Service.Main DEBUG Exception: aborting sync, remote setup failed No traceback available 2010-05-02 21:16:09 Service.Main DEBUG Idle timer created for sync, will sync after 5 seconds of inactivity. 2010-05-02 21:16:30 Net.Resource DEBUG GET success 200 https://sj-weave03.services.mozilla.com/1.0/mehper/storage/meta/global 2010-05-02 21:16:30 Service.Main DEBUG Weave Version: 1.2.3 Local Storage: 2 Remote Storage: 2 2010-05-02 21:26:50 Net.Resource DEBUG GET success 200 https://sj-weave03.services.mozilla.com/1.0/mehper/info/collections 2010-05-02 21:26:50 Engine.Clients INFO 0 outgoing items pre-reconciliation 2010-05-02 21:26:50 Engine.Clients INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:26:50 Engine.Clients DEBUG Total (ms): sync 6, processIncoming 3, uploadOutgoing 0, syncStartup 3, syncFinish 0 2010-05-02 21:26:50 Engine.Bookmarks INFO 0 outgoing items pre-reconciliation 2010-05-02 21:26:50 Engine.Bookmarks INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:26:50 Engine.Bookmarks DEBUG Total (ms): sync 13, processIncoming 5, uploadOutgoing 0, syncStartup 3, syncFinish 3 2010-05-02 21:26:50 Engine.Forms INFO 1 outgoing items pre-reconciliation 2010-05-02 21:26:50 Engine.Forms INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:26:50 Engine.Forms INFO Uploading all of 1 records 2010-05-02 21:26:50 Collection DEBUG POST Length: 388 2010-05-02 21:27:06 Collection DEBUG POST success 200 https://sj-weave03.services.mozilla.com/1.0/mehper/storage/forms 2010-05-02 21:27:06 Engine.Forms DEBUG Total (ms): sync 15924, processIncoming 3, uploadOutgoing 15918, syncStartup 3, syncFinish 0, createRecord 1 2010-05-02 21:27:06 Engine.History INFO 55 outgoing items pre-reconciliation 2010-05-02 21:27:06 Engine.History INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:27:09 Engine.History INFO Uploading all of 55 records 2010-05-02 21:27:09 Collection DEBUG POST Length: 35337 2010-05-02 21:27:32 Collection DEBUG POST success 200 https://sj-weave03.services.mozilla.com/1.0/mehper/storage/history 2010-05-02 21:27:32 Engine.History DEBUG Total (ms): sync 25588, processIncoming 4, uploadOutgoing 25580, syncStartup 3, syncFinish 0, createRecord 2540 2010-05-02 21:27:32 Engine.Passwords INFO 0 outgoing items pre-reconciliation 2010-05-02 21:27:32 Engine.Passwords INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:27:32 Engine.Passwords DEBUG Total (ms): sync 8, processIncoming 4, uploadOutgoing 0, syncStartup 4, syncFinish 0 2010-05-02 21:27:32 Engine.Prefs INFO 0 outgoing items pre-reconciliation 2010-05-02 21:27:32 Engine.Prefs INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:27:32 Engine.Prefs DEBUG Total (ms): sync 8, processIncoming 3, uploadOutgoing 0, syncStartup 4, syncFinish 0 2010-05-02 21:27:32 Engine.Tabs INFO 1 outgoing items pre-reconciliation 2010-05-02 21:27:32 Engine.Tabs INFO Records: 0 applied, 0 reconciled, 0 left to fetch 2010-05-02 21:27:32 Engine.Tabs INFO Uploading all of 1 records 2010-05-02 21:27:32 Collection DEBUG POST Length: 393 2010-05-02 21:27:54 Collection DEBUG POST success 200 https://sj-weave03.services.mozilla.com/1.0/mehper/storage/tabs 2010-05-02 21:27:54 Engine.Tabs DEBUG Total (ms): sync 21943, processIncoming 3, uploadOutgoing 21936, syncStartup 3, syncFinish 0, createRecord 8 2010-05-02 21:27:54 Service.Main INFO Sync completed successfully 2010-05-02 22:27:53 Service.Main DEBUG Idle timer created for sync, will sync after 5 seconds of inactivity. 2010-05-02 22:28:14 Net.Resource DEBUG GET success 200 https://sj-weave03.services.mozilla.com/1.0/mehper/storage/meta/global 2010-05-02 22:28:14 Service.Main DEBUG Weave Version: 1.2.3 Local Storage: 2 Remote Storage: 2 2010-05-02 22:28:16 Net.Resource DEBUG GET fail 503 https://sj-weave03.services.mozilla.com/1.0/mehper/info/collections 2010-05-02 22:28:16 Service.Main DEBUG Exception: aborting sync, failed to get collections No traceback available 2010-05-02 23:28:15 Service.Main DEBUG Idle timer created for sync, will sync after 5 seconds of inactivity. 2010-05-03 00:26:42 Service.Main DEBUG Exception: Could not acquire lock No traceback available 2010-05-03 00:31:03 RecordMgr DEBUG Failed to import record: App. Quitting JS Stack trace: Res__request(...)@resource.js:208 < Res_get()@resource.js:271 < RecordMgr_import("https://sj-weave03.services.mozilla.com/1.0/mehper/storage/meta/global")@wbo.js:119 < WeaveSvc__remoteSetup()@service.js:824 < ()@service.js:1187 < WrappedNotify()@util.js:114 < WrappedLock()@util.js:86 < WrappedCatch()@util.js:65 < sync(false)@service.js:1146 < ([object Object])@service.js:414 < notify([object XPCWrappedNative_NoHelper])@util.js:629 2010-05-03 00:31:03 Service.Main DEBUG Weave Version: 1.2.3 Local Storage: 2 Remote Storage: 2010-05-03 00:31:03 Service.Main WARN Unknown error while downloading metadata record. Aborting sync. 2010-05-03 00:31:03 Service.Main DEBUG Exception: aborting sync, remote setup failed No traceback available 2010-05-03 17:26:25 Service.Main INFO Loading Weave 1.2.3 2010-05-03 17:26:25 Engine.Bookmarks DEBUG Engine initialized 2010-05-03 17:26:25 Engine.Forms DEBUG Engine initialized 2010-05-03 17:26:25 Engine.History DEBUG Engine initialized 2010-05-03 17:26:25 Engine.Passwords DEBUG Engine initialized 2010-05-03 17:26:25 Engine.Prefs DEBUG Engine initialized 2010-05-03 17:26:25 Engine.Tabs DEBUG Engine initialized 2010-05-03 17:26:25 Engine.Tabs DEBUG Resetting tabs last sync time 2010-05-03 17:26:25 Service.Main INFO Mozilla/5.0 (Windows; U; Windows NT 6.1; tr; rv:1.9.2.3) Gecko/20100401 Firefox/3.6.3 (.NET CLR 3.5.30729) 2010-05-03 17:26:26 Service.Main DEBUG Caching URLs under storage user base: https://sj-weave03.services.mozilla.com/1.0/mehper/ 2010-05-03 17:26:30 Service.Main DEBUG Autoconnecting in 3 seconds 2010-05-03 17:26:36 Service.Main INFO Logging in user mehper 2010-05-03 17:45:46 Service.Main DEBUG Exception: Could not acquire lock No traceback available 2010-05-03 17:53:18 Service.Main DEBUG Exception: Could not acquire lock No traceback available

  Read the article

• Poor upload/download speed on 2 x ADSL lines into a Cisco 2621XM

  - by 2020mobile

  Hi, Sorry never been on this site before so I apologise if not the right section or even forum. I have users complaining of very slow internetn connectivity on site and have checked with our ISP who have said that the line is testing at 8mb. We have 2 x BT lines that have our ISP broadand on them. Both lines go into a Cisco 2600 series router that then has a PIX firewall off that. Connectivity is successful just gone really slow and unable to download anything. Config is below: version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ROUTER-ADSL-INTERNET ! logging buffered 16384 informational enable secret xxx enable password xxx ! username xxx username xxx clock summer-time UK recurring last Sun Mar 1:00 last Sun Oct 1:00 aaa new-model ! ! aaa authentication login default local aaa authorization exec default local aaa session-id common ip subnet-zero no ip source-route ! ! ! ip audit notify log ip audit po max-events 100 no ip bootp server ip name-server 213.208.106.212 no mpls ldp logging neighbor-changes no ftp-server write-enable ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! ! ! ! ! ! ! interface ATM0/0 description 01270 111111 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/0 ip address 82.133.32.9 255.255.255.248 shutdown speed 100 full-duplex no cdp enable ! interface ATM0/1 description 01270 222222 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/1 ip address 217.146.115.49 255.255.255.240 duplex auto speed auto no cdp enable ! interface Dialer0 ip address 217.146.115.250 255.255.255.248 encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap callin ppp chap hostname [email protected] ppp chap password 7 xxxxx ppp multilink ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! no logging trap access-list 10 permit 217.146.115.50 access-list 10 permit 82.133.32.10 access-list 10 deny any access-list 22 permit 217.146.115.50 access-list 22 permit 217.206.239.86 access-list 22 permit 82.133.32.10 access-list 22 deny any dialer-list 1 protocol ip permit no cdp run ! ! snmp-server community xxxxxx RO 10 snmp-server enable traps tty radius-server authorization permit missing Service-Type ! ! ! ! ! ! line con 0 exec-timeout 5 0 password 7 xxxxxx line aux 0 no exec line vty 0 4 access-class 22 in exec-timeout 5 0 password 7 xxxxxx transport input telnet ssh transport output none line vty 5 15 password 7 xxxxxx transport input telnet ssh ! ntp clock-period 17180095 ntp server 130.88.200.98 ! ! end Now my knowledge is very limited but ISP have said that while the lines are bonded each needs a seperate login as they've recently changed their L2TP router and that enforces the use of seperate logins - when the lines were configured we were given two logins. So, my question is what changes do I need to make to the config in order to get this working? it was ok before their change and I do have another login :- 01270 111111 - [email protected] 01270 222222 - [email protected] Apologies for the long email and thanks for taking the time to read it. Any more info I can provide please let me know. Thanks,

  Read the article

• Windows Server 2008 Task Scheduler Tasks Not Executing

  - by omatase

  I've been having an intermittent problem for some time now with the Windows Task Scheduler that I can't work out. I use the task scheduler to run a C# app I've written that has various plugins used to ensure production systems are working. This task scheduler itself is actually a production system so I have one simple task that executes every 8 minutes to notify an external monitoring system that the task scheduler is still up. If this external service fails to receive an "all-clear" at least once every 15 minutes (or so I don't remember the exact number right now) it will message us that the monitoring system is down. In the past we've had intermittent "down" messages from time to time and each time I've investigated the cause I was unable to find any problems. So this time I wanted to ask the StackOverflow community since it doesn't look like I'll have luck on my own. This morning at 2:32 AM the task fired (exactly 8 minutes after the previous firing) however the task didn't fire again until 3:28. There are no errors that I can see in the Event Viewer at this time. When I look at the Task Scheduler log there are no errors there either. Here is what the log looks like though: Information 6/11/2011 3:28:56 AM 102 Task completed (2) d6cf2412-269e-48bf-9f40-4a863347baad Information 6/11/2011 3:28:56 AM 201 Action completed (2) d6cf2412-269e-48bf-9f40-4a863347baad Information 6/11/2011 3:28:55 AM 129 Created Task Process Info Information 6/11/2011 3:28:55 AM 200 Action started (1) d6cf2412-269e-48bf-9f40-4a863347baad Information 6/11/2011 3:28:55 AM 100 Task Started (1) d6cf2412-269e-48bf-9f40-4a863347baad Information 6/11/2011 3:28:55 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:55 AM 107 Task triggered on scheduler Info d6cf2412-269e-48bf-9f40-4a863347baad Information 6/11/2011 3:28:15 AM 102 Task completed (2) b91fe5ce-39ef-42fb-adbe-bd8be012c00a Information 6/11/2011 3:28:15 AM 201 Action completed (2) b91fe5ce-39ef-42fb-adbe-bd8be012c00a Information 6/11/2011 3:28:15 AM 102 Task completed (2) 556c07dc-2724-4a21-a97e-dc4abd56f94d Information 6/11/2011 3:28:15 AM 201 Action completed (2) 556c07dc-2724-4a21-a97e-dc4abd56f94d Information 6/11/2011 3:28:15 AM 102 Task completed (2) 79328289-f742-49dd-aa0d-c3d05db50895 Information 6/11/2011 3:28:15 AM 201 Action completed (2) 79328289-f742-49dd-aa0d-c3d05db50895 Information 6/11/2011 3:28:15 AM 102 Task completed (2) 19743755-47b6-4b98-9bec-052193be9496 Information 6/11/2011 3:28:15 AM 201 Action completed (2) 19743755-47b6-4b98-9bec-052193be9496 Information 6/11/2011 3:28:15 AM 102 Task completed (2) c165754f-e3e6-4176-a327-11f9c06c39a5 Information 6/11/2011 3:28:15 AM 201 Action completed (2) c165754f-e3e6-4176-a327-11f9c06c39a5 Information 6/11/2011 3:28:15 AM 102 Task completed (2) 0e62ad3e-1f6e-40c0-9155-19f0108dee22 Information 6/11/2011 3:28:15 AM 201 Action completed (2) 0e62ad3e-1f6e-40c0-9155-19f0108dee22 Information 6/11/2011 3:28:10 AM 129 Created Task Process Info Information 6/11/2011 3:28:10 AM 200 Action started (1) 0e62ad3e-1f6e-40c0-9155-19f0108dee22 Information 6/11/2011 3:28:10 AM 129 Created Task Process Info Information 6/11/2011 3:28:10 AM 200 Action started (1) c165754f-e3e6-4176-a327-11f9c06c39a5 Information 6/11/2011 3:28:10 AM 129 Created Task Process Info Information 6/11/2011 3:28:10 AM 200 Action started (1) 19743755-47b6-4b98-9bec-052193be9496 Information 6/11/2011 3:28:10 AM 129 Created Task Process Info Information 6/11/2011 3:28:10 AM 200 Action started (1) 79328289-f742-49dd-aa0d-c3d05db50895 Information 6/11/2011 3:28:10 AM 129 Created Task Process Info Information 6/11/2011 3:28:10 AM 200 Action started (1) 556c07dc-2724-4a21-a97e-dc4abd56f94d Information 6/11/2011 3:28:10 AM 129 Created Task Process Info Information 6/11/2011 3:28:10 AM 200 Action started (1) b91fe5ce-39ef-42fb-adbe-bd8be012c00a Information 6/11/2011 3:28:10 AM 100 Task Started (1) 0e62ad3e-1f6e-40c0-9155-19f0108dee22 Information 6/11/2011 3:28:10 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:10 AM 100 Task Started (1) c165754f-e3e6-4176-a327-11f9c06c39a5 Information 6/11/2011 3:28:10 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:10 AM 100 Task Started (1) 19743755-47b6-4b98-9bec-052193be9496 Information 6/11/2011 3:28:10 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:10 AM 100 Task Started (1) 79328289-f742-49dd-aa0d-c3d05db50895 Information 6/11/2011 3:28:10 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:10 AM 100 Task Started (1) 556c07dc-2724-4a21-a97e-dc4abd56f94d Information 6/11/2011 3:28:10 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:10 AM 100 Task Started (1) b91fe5ce-39ef-42fb-adbe-bd8be012c00a Information 6/11/2011 3:28:10 AM 319 Task Engine received message to start task (1) Information 6/11/2011 3:28:10 AM 107 Task triggered on scheduler Info 0e62ad3e-1f6e-40c0-9155-19f0108dee22 Information 6/11/2011 3:28:10 AM 107 Task triggered on scheduler Info c165754f-e3e6-4176-a327-11f9c06c39a5 Information 6/11/2011 3:28:10 AM 107 Task triggered on scheduler Info 19743755-47b6-4b98-9bec-052193be9496 Information 6/11/2011 3:28:10 AM 107 Task triggered on scheduler Info 79328289-f742-49dd-aa0d-c3d05db50895 Information 6/11/2011 3:28:10 AM 107 Task triggered on scheduler Info 556c07dc-2724-4a21-a97e-dc4abd56f94d Information 6/11/2011 3:28:10 AM 107 Task triggered on scheduler Info b91fe5ce-39ef-42fb-adbe-bd8be012c00a Information 6/11/2011 2:32:56 AM 102 Task completed (2) 16e4f2c3-a340-410a-9c14-4bfe0861fdd5 Information 6/11/2011 2:32:56 AM 201 Action completed (2) 16e4f2c3-a340-410a-9c14-4bfe0861fdd5 Information 6/11/2011 2:32:55 AM 129 Created Task Process Info Information 6/11/2011 2:32:55 AM 200 Action started (1) 16e4f2c3-a340-410a-9c14-4bfe0861fdd5 Information 6/11/2011 2:32:55 AM 100 Task Started (1) 16e4f2c3-a340-410a-9c14-4bfe0861fdd5 Information 6/11/2011 2:32:55 AM 319 Task Engine received message to start task (1) Information 6/11/2011 2:32:55 AM 107 Task triggered on scheduler Info 16e4f2c3-a340-410a-9c14-4bfe0861fdd5 Seems kind of strange. I also have two other C# apps that run and check something each hour on the hour using task scheduler. If I look at the history for those I can see that they didn't execute at 3 AM either! They all waited until 3:28 to start as well. If I look at "tasks completed" in the Event Viewer it shows that only one task was able to run between the 2:32 AM to 3:28 AM time period. The task was "\Microsoft\Windows\RAC\RACAgent" And here's what it looked like: Information 6/11/2011 3:18:09 AM 102 Task completed (2) 00c53a85-ba20-4666-80db-fbbe2492c0ad Information 6/11/2011 3:18:09 AM 201 Action completed (2) 00c53a85-ba20-4666-80db-fbbe2492c0ad Information 6/11/2011 3:18:08 AM 129 Created Task Process Info Information 6/11/2011 3:18:08 AM 200 Action started (1) 00c53a85-ba20-4666-80db-fbbe2492c0ad Information 6/11/2011 3:18:08 AM 100 Task Started (1) 00c53a85-ba20-4666-80db-fbbe2492c0ad Information 6/11/2011 3:18:08 AM 319 Task Engine received message to start task (1) I appreciate any ideas anyone may have.

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39  | Next Page >