Search Results

Search found 913 results on 37 pages for 'rebooting'.

Page 35/37 | < Previous Page | 31 32 33 34 35 36 37  | Next Page >

• I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

  - by user69670

  Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

  Read the article

• Why is my Ubuntu system not using the correct kernel?

  - by Brooks Moses

  We're having a bit of confusion on a Ubuntu remote system -- /boot/grub/menu.lst suggests the system should boot into kernel 2.6.35-30-generic, but it is actually running kernel 2.6.32-27-generic. Where should I look to start figuring out why this is happening and how to fix it? Specifically, /boot/grub/menu.lst has default 0 and the first entry is title Ubuntu 10.10, kernel 2.6.35-30-generic uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.35-30-generic root=UUID=67717ee3-cbf9-45d2- ae97-820256f4c4fd ro quiet splash initrd /boot/initrd.img-2.6.35-30-generic Further, I've confirmed that /boot/vmlinuz-2.6.35-30-generic and /boot/initrd.img-2.6.35-30-generic exist and have appropriate permissions. Meanwhile, uname -a returns: $ uname -a Linux cuda2 2.6.32-27-generic #49-Ubuntu SMP Thu Dec 2 00:51:09 UTC 2010 x86_64 GNU/Linux Edit: I've also tried re-running update-grub, and rebooting; no luck. Here's the full menu.lst, as requested by a commenter: # menu.lst - See: grub(8), info grub, update-grub(8) # grub-install(8), grub-floppy(8), # grub-md5-crypt, /usr/share/doc/grub # and /usr/share/doc/grub-legacy-doc/. ## default num # Set the default entry to the entry number NUM. Numbering starts from 0, and # the entry number 0 is the default if the command is not used. # # You can specify 'saved' instead of a number. In this case, the default entry # is the entry saved with the command 'savedefault'. # WARNING: If you are using dmraid do not use 'savedefault' or your # array will desync and will not let you boot your system. default 0 ## timeout sec # Set a timeout, in SEC seconds, before automatically booting the default entry # (normally the first entry defined). timeout 3 ## hiddenmenu # Hides the menu by default (press ESC to see the menu) hiddenmenu # Pretty colours #color cyan/blue white/blue ## password ['--md5'] passwd # If used in the first section of a menu file, disable all interactive editing # control (menu entry editor and command-line) and entries protected by the # command 'lock' # e.g. password topsecret # password --md5 $1$gLhU0/$aW78kHK1QfV3P2b2znUoe/ # password topsecret # # examples # # title Windows 95/98/NT/2000 # root (hd0,0) # makeactive # chainloader +1 # # title Linux # root (hd0,1) # kernel /vmlinuz root=/dev/hda2 ro # # # Put static boot stanzas before and/or after AUTOMAGIC KERNEL LIST ### BEGIN AUTOMAGIC KERNELS LIST ## lines between the AUTOMAGIC KERNELS LIST markers will be modified ## by the debian update-grub script except for the default options below ## DO NOT UNCOMMENT THEM, Just edit them to your needs ## ## Start Default Options ## ## default kernel options ## default kernel options for automagic boot options ## If you want special options for specific kernels use kopt_x_y_z ## where x.y.z is kernel version. Minor versions can be omitted. ## e.g. kopt=root=/dev/hda1 ro ## kopt_2_6_8=root=/dev/hdc1 ro ## kopt_2_6_8_2_686=root=/dev/hdc2 ro # kopt=root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro ## default grub root device ## e.g. groot=(hd0,0) # groot=67717ee3-cbf9-45d2-ae97-820256f4c4fd ## should update-grub create alternative automagic boot options ## e.g. alternative=true ## alternative=false # alternative=true ## should update-grub lock alternative automagic boot options ## e.g. lockalternative=true ## lockalternative=false # lockalternative=false ## additional options to use with the default boot option, but not with the ## alternatives ## e.g. defoptions=vga=791 resume=/dev/hda5 # defoptions=quiet splash ## should update-grub lock old automagic boot options ## e.g. lockold=false ## lockold=true # lockold=false ## Xen hypervisor options to use with the default Xen boot option # xenhopt= ## Xen Linux kernel options to use with the default Xen boot option # xenkopt=console=tty0 ## altoption boot targets option ## multiple altoptions lines are allowed ## e.g. altoptions=(extra menu suffix) extra boot options ## altoptions=(recovery) single # altoptions=(recovery mode) single ## controls how many kernels should be put into the menu.lst ## only counts the first occurence of a kernel, not the ## alternative kernel options ## e.g. howmany=all ## howmany=7 # howmany=all ## specify if running in Xen domU or have grub detect automatically ## update-grub will ignore non-xen kernels when running in domU and vice versa ## e.g. indomU=detect ## indomU=true ## indomU=false # indomU=detect ## should update-grub create memtest86 boot option ## e.g. memtest86=true ## memtest86=false # memtest86=true ## should update-grub adjust the value of the default booted system ## can be true or false # updatedefaultentry=false ## should update-grub add savedefault to the default options ## can be true or false # savedefault=false ## ## End Default Options ## title Ubuntu 10.10, kernel 2.6.35-30-generic uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.35-30-generic root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro quiet splash initrd /boot/initrd.img-2.6.35-30-generic title Ubuntu 10.10, kernel 2.6.35-30-generic (recovery mode) uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.35-30-generic root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro single initrd /boot/initrd.img-2.6.35-30-generic title Ubuntu 10.10, kernel 2.6.32-32-server uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.32-32-server root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro quiet splash initrd /boot/initrd.img-2.6.32-32-server title Ubuntu 10.10, kernel 2.6.32-32-server (recovery mode) uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.32-32-server root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro single initrd /boot/initrd.img-2.6.32-32-server title Ubuntu 10.10, kernel 2.6.32-27-generic uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.32-27-generic root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro quiet splash initrd /boot/initrd.img-2.6.32-27-generic title Ubuntu 10.10, kernel 2.6.32-27-generic (recovery mode) uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/vmlinuz-2.6.32-27-generic root=UUID=67717ee3-cbf9-45d2-ae97-820256f4c4fd ro single initrd /boot/initrd.img-2.6.32-27-generic title Chainload into GRUB 2 root 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/grub/core.img title Ubuntu 10.10, memtest86+ uuid 67717ee3-cbf9-45d2-ae97-820256f4c4fd kernel /boot/memtest86+.bin ### END DEBIAN AUTOMAGIC KERNELS LIST To add complication and joy to my life, this is a desktop machine in a remote datacenter; we don't have either local access or serial-console access. Suggestions?

  Read the article

• Sound issues after trying everything

  - by Lerp

  I cannot get my sound working properly, no matter what I do, there's always some problem. It's very annoying as it's the only thing preventing me from making Ubuntu my main OS. At the moment my sound always plays through both my speakers and my headphones regardless except the sound through the headphones is crackly. It is also a bit quiet even though everything is maxed. I've managed to improve the situation to a point where the sound out of my speakers is perfect but I have none at all from my headphones. I do have two connectors listed in the sound settings but regardless of which one is selected it always plays through the speakers. I think this might have something to do with the fact that my speakers are plugging into the front of my computer, typically the headphone jack, and my headphones are plugging into the back but when I try disconnecting the speakers from the front there is still no sound from the headphones. I fixed the speaker sound by going through the sound settings and making sure they were all set to 100% then rebooting. Things I have tried: Maxing everything and unmuting everything in alsamixer Uninstalling pulseaudio Making gstreamer use only alsa via gstreamer-properties. This worked with the sound test button including independent sound between headphones and speakers but when I reset the computer it no longer worked. So I tried setting it manually in gconf-editor which didn't work either. Reinstalling alsa and pulseaudio Setting the model in /etc/modprobe.d/alsa-base.conf to 6stack and 6stack-dig neither worked. Upgrading to 12.10 Here's some command output to help you diagnose my problem. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 sudo lshw -C sound *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:70 memory:f7ff8000-f7ffbfff cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 options snd-hda-intel model=6stack

  Read the article

• C# - Alternative to System.Timers.Timer, to call a function at a specific time.

  - by Fábio Antunes

  Hello everybody. I want to call a specific function on my C# application at a specific time. At first i thought about using a Timer (System.Time.Timer), but that soon became impossible to use. Why? Simple. The Timer Class requires a Interval in milliseconds, but considering that i might want the function to be executed, lets says in a week that would mean: 7 Days = 168 hours; 168 Hours = 10,080 minutes; 10,080 Minutes = 6,048,000 seconds; 6,048,000 Seconds = 6,048,000,000 milliseconds; So the Interval would be 6,048,000,000; Now lets remember that the Interval accepted data type is int, and as we know int range goes from -2,147,483,648 to 2,147,483,647. That makes Timer useless in this case once we cannot set a Interval bigger that 2,147,483,647 milliseconds. So i need a solution where i could specify when the function should be called. Something like this: solution.ExecuteAt = "30-04-2010 15:10:00"; solution.Function = "functionName"; solution.Start(); So when the System Time would reach "30-04-2010 15:10:00" the function would be executed in the application. How can this problem be solved? Thanks just by taking the time to read my question. But if you could provide me with some help i would be most grateful. Additional Info: What these functions will do? Getting climate information and based on that info: Starting / Shutting down other Applications (most of them Console Based); Sending custom Commands to those Console Applications; Power down, Rebooting, Sleep, Hibernate the computer; And if possible schedule the BIOS to Power Up the Computer; EDIT: It would seem that the Interval accepted data type is double, however if you set a value bigger that an int to the Interval, and call Start() it throws a exception [0, Int32.MaxValue]. EDIT 2: Jørn Schou-Rode suggested using Ncron to handle the scheduling tasks, and at first look this seems a good solution, but i would like to hear about some who as worked with it.

  Read the article

• Visual Studio soft-crashing when encountering XAML Errors in initialize.

  - by Aren

  I've been having some serious issues with Visual Studio 2010 as of late. It's been crashing in a peculiar way when I encounter certain types of XAML errors during the InitializeComponent() of a control/window. The program breaks and visual studio gears up like it's catching an exception (because it is) and then stops midway displaying a broken highlight in my XAML file with no details as to what is wrong. Example: There is not pop outs, or details Anywhere about what is wrong, only a callstack that points to my InitializeComponent() call. Now normally I'd just do some trial and error to fix this problem, and find out where i messed up, but the real problem isn't my code. Visual Studio is rendered completely useless at this point. It reports my application still in "Running" mode. The Stop/Break/Restart buttons on the toolbar or in the menus don't do anything (but grey out). Closing the application does not stop this behaviour, closing visual studio gets it stuck in a massive loop where it yells at me complaining every file open is not in the debug project, then repeats this process when i have exausted every open file. I have to force-close devenv.exe, and after this happening 3-4 times in a row it's a lot of wasted time (as my projects are usually pretty big and studio can be quite slow @ loading). To the point Has anyone else experienced this? How can I stop studio from locking up. Can I at LEAST get information out of this beast another way so i can fix my XAML error sooner rather than after 3-4 trial-and-error compiles yielding the same crash? Any & All help would be appreciated. Visual Studio 2010 version: 10.0.30319.1RTM Edit & Update FWIW, mostly the errors that cause this are XamlParseExceptions (I figured this out after i found what was wrong with my XAML). I think I need to be clearer though, Im not looking for the solution to my code problem, as these are usually typos / small things, I'm looking for a solution to VStudio getting all buggered up as a result. The particular error in the above image that 100% for sure caused this was a XamlParseException caused by forgetting a Value attribute on a data trigger. I've fixed that part but it still doesn't tell my why my studio becomes a lump of neutered program when a perfectly normal exception is thrown in the parsing of the XAML. Code that will cause this issue (at least for me) This is the base template WPF Application, with the following Window.xaml code. The problem is a missing Value="True" on the <DataTrigger ...> in the template. It generates a XamlParseException and Visual Studio Crashes as described above when debugging it. Final Notes The following solutions did not help me: Restarting Visual Studio Rebooting Reinstalling Visual Studio

  Read the article

• Powershell script to change screen Orientation

  - by user161964

  I wrote a script to change Primary screen orientation to portrait. my screen is 1920X1200 It runs and no error reported. But the screen does not rotated as i expected. The code was modified from Set-ScreenResolution (Andy Schneider) Does anybody can help me take a look? some reference site: 1.set-screenresolution http://gallery.technet.microsoft.com/ScriptCenter/2a631d72-206d-4036-a3f2-2e150f297515/ 2.C code for change oridentation (MSDN) Changing Screen Orientation Programmatically http://msdn.microsoft.com/en-us/library/ms812499.aspx my code as below: Function Set-ScreenOrientation { $pinvokeCode = @" using System; using System.Runtime.InteropServices; namespace Resolution { [StructLayout(LayoutKind.Sequential)] public struct DEVMODE1 { [MarshalAs(UnmanagedType.ByValTStr, SizeConst = 32)] public string dmDeviceName; public short dmSpecVersion; public short dmDriverVersion; public short dmSize; public short dmDriverExtra; public int dmFields; public short dmOrientation; public short dmPaperSize; public short dmPaperLength; public short dmPaperWidth; public short dmScale; public short dmCopies; public short dmDefaultSource; public short dmPrintQuality; public short dmColor; public short dmDuplex; public short dmYResolution; public short dmTTOption; public short dmCollate; [MarshalAs(UnmanagedType.ByValTStr, SizeConst = 32)] public string dmFormName; [MarshalAs(UnmanagedType.U4)] public short dmDisplayOrientation public short dmLogPixels; public short dmBitsPerPel; public int dmPelsWidth; public int dmPelsHeight; public int dmDisplayFlags; public int dmDisplayFrequency; public int dmICMMethod; public int dmICMIntent; public int dmMediaType; public int dmDitherType; public int dmReserved1; public int dmReserved2; public int dmPanningWidth; public int dmPanningHeight; }; class User_32 { [DllImport("user32.dll")] public static extern int EnumDisplaySettings(string deviceName, int modeNum, ref DEVMODE1 devMode); [DllImport("user32.dll")] public static extern int ChangeDisplaySettings(ref DEVMODE1 devMode, int flags); public const int ENUM_CURRENT_SETTINGS = -1; public const int CDS_UPDATEREGISTRY = 0x01; public const int CDS_TEST = 0x02; public const int DISP_CHANGE_SUCCESSFUL = 0; public const int DISP_CHANGE_RESTART = 1; public const int DISP_CHANGE_FAILED = -1; } public class PrmaryScreenOrientation { static public string ChangeOrientation() { DEVMODE1 dm = GetDevMode1(); if (0 != User_32.EnumDisplaySettings(null, User_32.ENUM_CURRENT_SETTINGS, ref dm)) { dm.dmDisplayOrientation = DMDO_90 dm.dmPelsWidth = 1200; dm.dmPelsHeight = 1920; int iRet = User_32.ChangeDisplaySettings(ref dm, User_32.CDS_TEST); if (iRet == User_32.DISP_CHANGE_FAILED) { return "Unable To Process Your Request. Sorry For This Inconvenience."; } else { iRet = User_32.ChangeDisplaySettings(ref dm, User_32.CDS_UPDATEREGISTRY); switch (iRet) { case User_32.DISP_CHANGE_SUCCESSFUL: { return "Success"; } case User_32.DISP_CHANGE_RESTART: { return "You Need To Reboot For The Change To Happen.\n If You Feel Any Problem After Rebooting Your Machine\nThen Try To Change Resolution In Safe Mode."; } default: { return "Failed"; } } } } else { return "Failed To Change."; } } private static DEVMODE1 GetDevMode1() { DEVMODE1 dm = new DEVMODE1(); dm.dmDeviceName = new String(new char[32]); dm.dmFormName = new String(new char[32]); dm.dmSize = (short)Marshal.SizeOf(dm); return dm; } } } "@ Add-Type $pinvokeCode -ErrorAction SilentlyContinue [Resolution.PrmaryScreenOrientation]::ChangeOrientation() }

  Read the article

• DHCPDISCOVER requests from an off-by-one MAC address

  - by Aleksandr Levchuk

  In a Linux DHCP server I'm getting a bunch of these log lines: dhcpd: DHCPDISCOVER from 00:30:48:fe:5c:9c via eth1: network 192.168.2.0/24: no free leases I don't have any machines with 00:30:48:fe:5c:9c and I don't intend to give out an IP to 00:30:48:fe:5c:9c (whatever that could be). I tracked down the server that this is coming from and killed all the DHCP clients that were running but the DHCPDISCOVER requests do not stop. I can prove that this is the sending server by pulling the Ethernet cable - the requests stop. The strange thing is that the sending server only has 2 interfaces which are: 00:30:48:fe:5c:9a 00:30:48:fe:5c:9b What can be the cause of the off-by-one address? Who could be sending the requests? Details On the DHCP client: root@n34:~# ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 100 link/ether 00:30:48:fe:5c:9a brd ff:ff:ff:ff:ff:ff 3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 00:30:48:fe:5c:9b brd ff:ff:ff:ff:ff:ff 4: ib0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN qlen 256 link/infiniband 80:00:00:48:fe:80:00:00:00:00:00:00:00:02:c9:03:00:08:81:9f brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff 5: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast state UP qlen 256 link/infiniband 80:00:00:49:fe:80:00:00:00:00:00:00:00:02:c9:03:00:08:81:a0 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff Same info: root@n34:~# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:30:48:fe:5c:9a inet addr:192.168.2.234 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fefe:5c9a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72544 errors:0 dropped:0 overruns:0 frame:0 TX packets:152773 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:4908592 (4.6 MiB) TX bytes:89815782 (85.6 MiB) Memory:dfd60000-dfd80000 eth1 Link encap:Ethernet HWaddr 00:30:48:fe:5c:9b UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:dfde0000-dfe00000 ib0 Link encap:UNSPEC HWaddr 80-00-00-48-FE-80-00-00-00-00-00-00-00-00-00-00 BROADCAST MULTICAST MTU:2044 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:256 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ib1 Link encap:UNSPEC HWaddr 80-00-00-49-FE-80-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.3.234 Bcast:192.168.3.255 Mask:255.255.255.0 inet6 addr: fe80::202:c903:8:81a0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:2044 Metric:1 RX packets:1330 errors:0 dropped:0 overruns:0 frame:0 TX packets:255 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:256 RX bytes:716415 (699.6 KiB) TX bytes:17584 (17.1 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:560 (560.0 B) TX bytes:560 (560.0 B) The nodes were imaged with Perseus which uses kexec instead of rebooting.

  Read the article

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• Running TeamCity from Amazon EC2 - Cloud based scalable build and continuous Integration

  - by RoyOsherove

  I’ve been having fun playing with the amazon EC2 cloud service. I set up a server running TeamCity, and an image of a server that just runs a TeamCity agent. I also setup TeamCity  to automatically instantiate agents on EC2 and shut them down based upon availability of free agents. Here’s how I did it: The first step was setting up the teamcity server. Create an account on amazon EC2 (BTW, amazon’s sites works better in IE than it does in chrome.. who knew!?) Open the EC2 dashboard, and click “Launch Instance” . From the “Quick Start” tab I selected from the list: “Getting Started on Microsoft Windows Server 2008 (AMI Id: ami-c5e40dac)” .  it’s good enough to just run teamcity. In the instance details, I used the default (Small instance, 1.7 GB mem). You might want to choose a close availability zone based on where you are. We want to “Launch instances” so click continue. Select the default kernel, RAM disk and all. No need to enable monitoring for now (you can do that later). click continue. If you don’t have a key pair, you will be prompted to create one. Once you do, select it in the list. Now you’ll be prompted to create a security group. I named mine “TC” as in “TeamCity”. each group is a bunch of settings on which ports can be let through into and out of a hosted machine.  keep it as the default settings. We will change them later. Click continue,  review and then click “Launch”. Now you’ll be able to see the new instance in the running instances list on your site. Now, you need to install stuff on that instance (TeamCity!) . To do that, you’ll need to Remote desktop into that instance. To do that, we’ll get the admin password for that instance: Check it on the list, and click “Instance Actions” - “Get Windows Admin Password”. You might have to wait about 10 minutes or so for the password to be generated for you. Once you have the password, you will remote desktop (start-run-‘mstsc’) into the instance. It’s address is a dns address shown below the list under “Public DNS”. it looks something like: ec2-256-226-194-91.compute-1.amazonaws.com Once you’re inside the instance – you’ll need to open IE (it is in hardened mode so you’ll have to relax its security settings to download stuff). I first downloaded chrome and using chrome I downloaded TeamCity. Note that the download speed is FAST. several MBs per second. To be able to see TeamCity from the outside, you will need to open the advanced firewall settings inside the remote machine, and add incoming and outgoing rules for port 80 (HTTP). Once you do that, you should be able to see the machine from the outside. If you still can’t, see the next step. I also enabled ports 9090 since I will use this machine to create an agent image later as well. Now configure the security group (TC) to enable talking to agents: IN the EC2 dashboard click on “Security Groups” and select your group. To add a rule, click on the empty list under the ‘protocol’ header. select TCP. from and ‘to’ ports are 9090. source ip is 0.0.0.0/0 (every ip is allowed). click “Save.  Also make sure you can see “HTTP” tcp 80 in that list. if you can’t see it, add it or you won’t be able to browse to the machine’s teamcity server home page. I also set an elastic IP for the machine: so I always have the same IP for the machine instance. Allocate and set one through the”Elastic IP” link on the EC2 dashboard.   you should now have a working instance of teamcity.   Now let’s create an agent image. Repeat steps 1-9, but this time, make sure you select a machine that fits what an agent might do. I selected Instance type – Hihg-CPU medium machine,  that is much faster. On that machine, I installed what I needed (VS 2010, PostSharp etc..). downloading VS 2010 from MSDN (2 GB took less than 10 min!) Now, instead of installing teamcity, browse using the browser to the teamcity homepage (from within the remote machine). go to the Administration page, and click the upper right link “Install agents”. Install the agent on he local machine – set it to the IP or DNS of the running TeamCity server. That way you’ll be able to check their connectivity live before making this machine your official agent image to reuse. Once the agent is installed, see that the TC server can see it and use it. see steps 13-14 above if they can’t. Once it works, you can take steps to make this image your agent image to be reused. next, here is a copy-paste of several steps to take from http://confluence.jetbrains.net/display/TCD5/Setting+Up+TeamCity+for+Amazon+EC2 Configure system so that agent it is started on machine boot (and make sure TeamCity server is accessible on machine boot). Test the setup by rebooting machine and checking that the agent connects normally to the server. Prepare the Image for bundling: Remove any temporary/history information in the system. Stop the agent (under Windows stop the service but leave it in Automatic startup type) Delete content agent logs and temp directories (not necessary) Delete "<Agent Home>/conf/amazon-*" file (not necessary) Change config/buildAgent.properties to remove properties: name, serverAddress, authToken (not necessary)   Now, we need to: Make AMI from the running instance. Configure TeamCity EC2 support on TeamCity server. Making an AMI: Check the instance of the agent in the EC2 dashboard instance list, and select instance actions->Create Image (EBS AMI) you’ll see the image pending in the APIs list in the EC2 dashboard. this could take 30 minutes or more. meanwhile we can configure the could support in the teamcity server. COPY THE AMI ID to the clipboard (looks like ami-a88aa4ce) Configuring TeamCity for Cloud: In TeamCity, click on “Agents” and then on “Cloud” tab. this is where you will control your cloud agents. to configure new cloud agents based on APIs, click on the right link to the “configuration page” Create a new profile and select AMazon EC2 as cloud type. Use your AMI ID that you copied to the clipboard into the “Images” field. Select an availability zone that is the same as the one your instance is running on for best communication perf between them make sure you select the ‘TC’ security group hopefully, that should be it, and teamcity will try to instantiate new instances on demand. Note that it may take around 10 minutes for an agent to become available to teamcity from the time it’s started.

  Read the article

• Upgrading from 12.10 to 13.04 -> dpkg: error processing sudo (--configure)

  - by Korrigan Nagirrok

  Here's the deal and reason I'm asking for your help. Last night I went on upgrading my Xubuntu 12.10 installation to 13.04, so at tty1 I run the command sudo do-release-upgrade and everything seemed to went well except that after rebooting and when I run sudo apt-get update && sudo apt-get upgrade I get this error: sudo apt-get update && sudo apt-get upgrade Hit http://pt.archive.ubuntu.com raring Release.gpg Hit http://pt.archive.ubuntu.com raring-updates Release.gpg Hit http://dl.google.com stable Release.gpg Hit http://pt.archive.ubuntu.com raring-backports Release.gpg Hit http://pt.archive.ubuntu.com raring Release Hit http://archive.canonical.com raring Release.gpg Hit http://ppa.launchpad.net raring Release.gpg Hit http://pt.archive.ubuntu.com raring-updates Release Hit http://extras.ubuntu.com raring Release.gpg Hit http://pt.archive.ubuntu.com raring-backports Release Hit http://dl.google.com stable Release Hit http://pt.archive.ubuntu.com raring/main Sources Hit http://pt.archive.ubuntu.com raring/restricted Sources Hit http://extras.ubuntu.com raring Release Hit http://archive.canonical.com raring Release Hit http://ppa.launchpad.net raring Release.gpg Hit http://pt.archive.ubuntu.com raring/universe Sources Hit http://pt.archive.ubuntu.com raring/multiverse Sources Hit http://dl.google.com stable/main i386 Packages Get:1 http://security.ubuntu.com raring-security Release.gpg [933 B] Hit http://pt.archive.ubuntu.com raring/main i386 Packages Hit http://extras.ubuntu.com raring/main Sources Hit http://ppa.launchpad.net raring Release Hit http://archive.canonical.com raring/partner i386 Packages Hit http://pt.archive.ubuntu.com raring/restricted i386 Packages Hit http://pt.archive.ubuntu.com raring/universe i386 Packages Hit http://extras.ubuntu.com raring/main i386 Packages Hit http://pt.archive.ubuntu.com raring/multiverse i386 Packages Hit http://ppa.launchpad.net raring Release Hit http://pt.archive.ubuntu.com raring/main Translation-en Hit http://ppa.launchpad.net raring/main Sources Hit http://ppa.launchpad.net raring/main i386 Packages Hit http://pt.archive.ubuntu.com raring/multiverse Translation-en Hit http://pt.archive.ubuntu.com raring/restricted Translation-en Hit http://pt.archive.ubuntu.com raring/universe Translation-en Hit http://pt.archive.ubuntu.com raring-updates/main Sources Hit http://pt.archive.ubuntu.com raring-updates/restricted Sources Hit http://ppa.launchpad.net raring/main Sources Hit http://pt.archive.ubuntu.com raring-updates/universe Sources Hit http://pt.archive.ubuntu.com raring-updates/multiverse Sources Hit http://pt.archive.ubuntu.com raring-updates/main i386 Packages Hit http://ppa.launchpad.net raring/main i386 Packages Hit http://pt.archive.ubuntu.com raring-updates/restricted i386 Packages Hit http://pt.archive.ubuntu.com raring-updates/universe i386 Packages Hit http://pt.archive.ubuntu.com raring-updates/multiverse i386 Packages Ign http://dl.google.com stable/main Translation-en_US Hit http://pt.archive.ubuntu.com raring-updates/main Translation-en Ign http://archive.canonical.com raring/partner Translation-en_US Ign http://extras.ubuntu.com raring/main Translation-en_US Ign http://dl.google.com stable/main Translation-en Ign http://archive.canonical.com raring/partner Translation-en Hit http://pt.archive.ubuntu.com raring-updates/multiverse Translation-en Ign http://extras.ubuntu.com raring/main Translation-en Hit http://pt.archive.ubuntu.com raring-updates/restricted Translation-en Hit http://pt.archive.ubuntu.com raring-updates/universe Translation-en Hit http://pt.archive.ubuntu.com raring-backports/main Sources Hit http://pt.archive.ubuntu.com raring-backports/restricted Sources Hit http://pt.archive.ubuntu.com raring-backports/universe Sources Hit http://pt.archive.ubuntu.com raring-backports/multiverse Sources Hit http://pt.archive.ubuntu.com raring-backports/main i386 Packages Hit http://pt.archive.ubuntu.com raring-backports/restricted i386 Packages Hit http://pt.archive.ubuntu.com raring-backports/universe i386 Packages Hit http://pt.archive.ubuntu.com raring-backports/multiverse i386 Packages Hit http://pt.archive.ubuntu.com raring-backports/main Translation-en Hit http://pt.archive.ubuntu.com raring-backports/multiverse Translation-en Get:2 http://security.ubuntu.com raring-security Release [40.8 kB] Hit http://pt.archive.ubuntu.com raring-backports/restricted Translation-en Hit http://pt.archive.ubuntu.com raring-backports/universe Translation-en Ign http://ppa.launchpad.net raring/main Translation-en_US Ign http://ppa.launchpad.net raring/main Translation-en Get:3 http://security.ubuntu.com raring-security/main Sources [2,109 B] Ign http://ppa.launchpad.net raring/main Translation-en_US Ign http://ppa.launchpad.net raring/main Translation-en Get:4 http://security.ubuntu.com raring-security/restricted Sources [14 B] Get:5 http://security.ubuntu.com raring-security/universe Sources [14 B] Get:6 http://security.ubuntu.com raring-security/multiverse Sources [14 B] Get:7 http://security.ubuntu.com raring-security/main i386 Packages [3,670 B] Get:8 http://security.ubuntu.com raring-security/restricted i386 Packages [14 B] Get:9 http://security.ubuntu.com raring-security/universe i386 Packages [2,824 B] Get:10 http://security.ubuntu.com raring-security/multiverse i386 Packages [14 B] Ign http://pt.archive.ubuntu.com raring/main Translation-en_US Ign http://pt.archive.ubuntu.com raring/multiverse Translation-en_US Ign http://pt.archive.ubuntu.com raring/restricted Translation-en_US Ign http://pt.archive.ubuntu.com raring/universe Translation-en_US Ign http://pt.archive.ubuntu.com raring-updates/main Translation-en_US Ign http://pt.archive.ubuntu.com raring-updates/multiverse Translation-en_US Hit http://security.ubuntu.com raring-security/main Translation-en Ign http://pt.archive.ubuntu.com raring-updates/restricted Translation-en_US Ign http://pt.archive.ubuntu.com raring-updates/universe Translation-en_US Ign http://pt.archive.ubuntu.com raring-backports/main Translation-en_US Ign http://pt.archive.ubuntu.com raring-backports/multiverse Translation-en_US Ign http://pt.archive.ubuntu.com raring-backports/restricted Translation-en_US Hit http://security.ubuntu.com raring-security/multiverse Translation-en Ign http://pt.archive.ubuntu.com raring-backports/universe Translation-en_US Hit http://security.ubuntu.com raring-security/restricted Translation-en Hit http://security.ubuntu.com raring-security/universe Translation-en Ign http://security.ubuntu.com raring-security/main Translation-en_US Ign http://security.ubuntu.com raring-security/multiverse Translation-en_US Ign http://security.ubuntu.com raring-security/restricted Translation-en_US Ign http://security.ubuntu.com raring-security/universe Translation-en_US Fetched 50.4 kB in 6s (7,454 B/s) Reading package lists... Done Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 0 B/373 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y dpkg: error processing sudo (--configure): Package is in a very bad inconsistent state - you should reinstall it before attempting configuration. No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of ubuntu-minimal: ubuntu-minimal depends on sudo; however: Package sudo is not configured yet. dpkg: error processing ubuntu-minimal (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Errors were encountered while processing: sudo ubuntu-minimal E: Sub-process /usr/bin/dpkg returned an error code (1) I've tried everything I thought logical, like sudo dpkg --configure -a dpkg: error processing sudo (--configure): Package is in a very bad inconsistent state - you should reinstall it before attempting configuration. dpkg: dependency problems prevent configuration of ubuntu-minimal: ubuntu-minimal depends on sudo; however: Package sudo is not configured yet. dpkg: error processing ubuntu-minimal (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: sudo ubuntu-minimal sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 0 B/373 kB of archives. After this operation, 0 B of additional disk space will be used. dpkg: error processing sudo (--configure): Package is in a very bad inconsistent state - you should reinstall it before attempting configuration. dpkg: dependency problems prevent configuration of ubuntu-minimal: ubuntu-minimal depends on sudo; however: Package sudo is not configured yet. dpkg: error processing ubuntu-minimal (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already Errors were encountered while processing: sudo ubuntu-minimal E: Sub-process /usr/bin/dpkg returned an error code (1) Can someone help me, please. Edit: Here's some more info that could be of help for anyone. The output of apt-cache policy linux-image-generic-pae linux-generic-pae is linux-image-generic-pae: Installed: (none) Candidate: 3.8.0.19.35 Version table: 3.8.0.19.35 0 500 http://pt.archive.ubuntu.com/ubuntu/ raring/main i386 Packages linux-generic-pae: Installed: (none) Candidate: 3.8.0.19.35 Version table: 3.8.0.19.35 0 500 http://pt.archive.ubuntu.com/ubuntu/ raring/main i386 Packages

  Read the article

• Troubleshooting inconsistent ODBC connectivity

  - by Chris

  I'm attempting to integrate UPS WorldShip with a SQL Server 2008 R2 database but the connection is very inconsistent. UPS claims this is a DSN/Windows problem and I have not been able to convince them otherwise. The integration is quite simple: my shipping guy clicks a button which opens a form where he enters an order #. After pressing enter the shipping information will be pulled from the database for that order #. The problem is that WorldShip often times thinks the DSN does not exist. However, I am able to open WorldShip's customization tool and browse all the tables and fields in the database my DSN is connected to which means at the very least my DSN does, in fact, exist. The reason this has been so difficult to troubleshoot is because there is no consistency to the problem and I'm not able to reliably repeat any behavior. That is to say that rebooting the PC doesn't cause the connection to break and opening the integration tool and viewing the tables and fields doesn't cause the integration button to work. Is there some way for me to monitor this connection from the SQL server or get any clues as to why it fails? As requested by TallTed here is a sample of the trace file I created. After a mere 5 hours the trace file was over 130MB so there's no way I could provide it in its entirety. WorldShipTD d94-690 EXIT SQLSetStmtAttrW with return code -1 (SQL_ERROR) SQLHSTMT 0x0C6632A0 SQLINTEGER 1227 <unknown> SQLPOINTER [Unknown attribute 1227] SQLINTEGER -5 DIAG [IM006] [Microsoft][ODBC Driver Manager] Driver's SQLSetConnectAttr failed (0) WorldShipTD d94-690 ENTER SQLAllocHandle SQLSMALLINT 3 <SQL_HANDLE_STMT> SQLHANDLE 0x0C662FC0 SQLHANDLE * 0x03EBCE38 WorldShipTD d94-690 EXIT SQLAllocHandle with return code 0 (SQL_SUCCESS) SQLSMALLINT 3 <SQL_HANDLE_STMT> SQLHANDLE 0x0C662FC0 SQLHANDLE * 0x03EBCE38 ( 0x0C6632A0) WorldShipTD d94-690 ENTER SQLSetStmtAttrW SQLHSTMT 0x0C6632A0 SQLINTEGER 0 <SQL_ATTR_QUERY_TIMEOUT> SQLPOINTER 30 SQLINTEGER -5 WorldShipTD d94-690 EXIT SQLSetStmtAttrW with return code -1 (SQL_ERROR) SQLHSTMT 0x0C6632A0 SQLINTEGER 0 <SQL_ATTR_QUERY_TIMEOUT> SQLPOINTER 30 SQLINTEGER -5 DIAG [HYC00] [Microsoft][ODBC Microsoft Access Driver]Optional feature not implemented (106) WorldShipTD d94-690 ENTER SQLGetDiagFieldW SQLSMALLINT 3 SQLHANDLE 0x0C6632A0 SQLSMALLINT 1 SQLSMALLINT 4 SQLPOINTER 0x00520708 SQLSMALLINT 12 SQLSMALLINT * 0x0028E2A8 WorldShipTD d94-690 EXIT SQLGetDiagFieldW with return code 0 (SQL_SUCCESS) SQLSMALLINT 3 SQLHANDLE 0x0C6632A0 SQLSMALLINT 1 SQLSMALLINT 4 SQLPOINTER 0x00520708 SQLSMALLINT 12 SQLSMALLINT * 0x0028E2A8 (10) WorldShipTD d94-690 ENTER SQLGetInfoW HDBC 0x0C662FC0 UWORD 77 <SQL_DRIVER_ODBC_VER> PTR 0x03EBCEDC SWORD 100 SWORD * 0x0028E290 WorldShipTD d94-690 EXIT SQLGetInfoW with return code 0 (SQL_SUCCESS) HDBC 0x0C662FC0 UWORD 77 <SQL_DRIVER_ODBC_VER> PTR 0x03EBCEDC [ 10] "03.51" SWORD 100 SWORD * 0x0028E290 (10) WorldShipTD d94-690 ENTER SQLSetStmtAttrW SQLHSTMT 0x0C6632A0 SQLINTEGER 1228 <unknown> SQLPOINTER [Unknown attribute 1228] SQLINTEGER -5 WorldShipTD d94-690 EXIT SQLSetStmtAttrW with return code -1 (SQL_ERROR) SQLHSTMT 0x0C6632A0 SQLINTEGER 1228 <unknown> SQLPOINTER [Unknown attribute 1228] SQLINTEGER -5 DIAG [HY092] [Microsoft][ODBC Microsoft Access Driver]Invalid attribute/option identifier (86) WorldShipTD d94-690 ENTER SQLGetDiagFieldW SQLSMALLINT 3 SQLHANDLE 0x0C6632A0 SQLSMALLINT 1 SQLSMALLINT 4 SQLPOINTER 0x00520708 SQLSMALLINT 12 SQLSMALLINT * 0x0028E2A8 WorldShipTD d94-690 EXIT SQLGetDiagFieldW with return code 0 (SQL_SUCCESS) SQLSMALLINT 3 SQLHANDLE 0x0C6632A0 SQLSMALLINT 1 SQLSMALLINT 4 SQLPOINTER 0x00520708 SQLSMALLINT 12 SQLSMALLINT * 0x0028E2A8 (10) WorldShipTD d94-690 ENTER SQLSetStmtAttrW SQLHSTMT 0x0C6632A0 SQLINTEGER 1227 <unknown> SQLPOINTER [Unknown attribute 1227] SQLINTEGER -5 WorldShipTD d94-690 EXIT SQLSetStmtAttrW with return code -1 (SQL_ERROR) SQLHSTMT 0x0C6632A0 SQLINTEGER 1227 <unknown> SQLPOINTER [Unknown attribute 1227] SQLINTEGER -5 DIAG [HY092] [Microsoft][ODBC Microsoft Access Driver]Invalid attribute/option identifier (86) WorldShipTD d94-690 ENTER SQLGetDiagFieldW SQLSMALLINT 3 SQLHANDLE 0x0C6632A0 SQLSMALLINT 1 SQLSMALLINT 4 SQLPOINTER 0x00520708 SQLSMALLINT 12 SQLSMALLINT * 0x0028E2A8 WorldShipTD d94-690 EXIT SQLGetDiagFieldW with return code 0 (SQL_SUCCESS) SQLSMALLINT 3 SQLHANDLE 0x0C6632A0 SQLSMALLINT 1 SQLSMALLINT 4 SQLPOINTER 0x00520708 SQLSMALLINT 12 SQLSMALLINT * 0x0028E2A8 (10)

  Read the article

• Running Solaris 11 as a control domain on a T2000

  - by jsavit

  There is increased adoption of Oracle Solaris 11, and many customers are deploying it on systems that previously ran Solaris 10. That includes older T1-processor based systems like T1000 and T2000. Even though they are old (from 2005) and don't have the performance of current SPARC servers, they are still functional, stable servers that customers continue to operate. One reason to install Solaris 11 on them is that older machines are attractive for testing OS upgrades before updating current, production systems. Normally this does not present a challenge, because Solaris 11 runs on any T-series or M-series SPARC server. One scenario adds a complication: running Solaris 11 in a control domain on a T1000 or T2000 hosting logical domains. Solaris 11 pre-installed Oracle VM Server for SPARC incompatible with T1 Unlike Solaris 10, Solaris 11 comes with Oracle VM Server for SPARC preinstalled. The ldomsmanager package contains the logical domains manager for Oracle VM Server for SPARC 2.2, which requires a SPARC T2, T2+, T3, or T4 server. It does not work with T1-processor systems, which are only supported by LDoms Manager 1.2 and earlier. The following screenshot shows what happens (bold font) if you try to use Oracle VM Server for SPARC 2.x commands in a Solaris 11 control domain. The commands were issued in a control domain on a T2000 that previously ran Solaris 10. We also display the version of the logical domains manager installed in Solaris 11: root@t2000 psrinfo -vp The physical processor has 4 virtual processors (0-3) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep T SUNW,Sun-Fire-T200 # ldm -V Failed to connect to logical domain manager: Connection refused # pkg info ldomsmanager Name: system/ldoms/ldomsmanager Summary: Logical Domains Manager Description: LDoms Manager - Virtualization for SPARC T-Series Category: System/Virtualization State: Installed Publisher: solaris Version: 2.2.0.0 Build Release: 5.11 Branch: 0.175.0.8.0.3.0 Packaging Date: May 25, 2012 10:20:48 PM Size: 2.86 MB FMRI: pkg://solaris/system/ldoms/[email protected],5.11-0.175.0.8.0.3.0:20120525T222048Z The 2.2 version of the logical domains manager will have to be removed, and 1.2 installed, in order to use this as a control domain. Preparing to change - create a new boot environment Before doing anything else, lets create a new boot environment: # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris NR / 2.14G static 2012-09-25 10:32 # beadm create solaris-1 # beadm activate solaris-1 # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris N / 4.82M static 2012-09-25 10:32 solaris-1 R - 2.14G static 2012-09-29 11:40 # init 0 Normally an init 6 to reboot would have been sufficient, but in the next step I reset the system anyway in order to put the system in factory default mode for a "clean" domain configuration. Preparing to change - reset to factory default There was a leftover domain configuration on the T2000, so I reset it to the factory install state. Since the ldm command is't working yet, it can't be done from the control domain, so I did it by logging onto to the service processor: $ ssh -X admin@t2000-sc Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved. Oracle Advanced Lights Out Manager CMT v1.7.9 Please login: admin Please Enter password: ******** sc> showhost Sun-Fire-T2000 System Firmware 6.7.10 2010/07/14 16:35 Host flash versions: OBP 4.30.4.b 2010/07/09 13:48 Hypervisor 1.7.3.c 2010/07/09 15:14 POST 4.30.4.b 2010/07/09 14:24 sc> bootmode config="factory-default" sc> poweroff Are you sure you want to power off the system [y/n]? y SC Alert: SC Request to Power Off Host. SC Alert: Host system has shut down. sc> poweron SC Alert: Host System has Reset At this point I rebooted into the new Solaris 11 boot environment, and Solaris commands showed it was running on the factory default configuration of a single domain owning all 32 CPUs and 32GB of RAM (that's what it looked like in 2005.) # psrinfo -vp The physical processor has 8 cores and 32 virtual processors (0-31) The core has 4 virtual processors (0-3) The core has 4 virtual processors (4-7) The core has 4 virtual processors (8-11) The core has 4 virtual processors (12-15) The core has 4 virtual processors (16-19) The core has 4 virtual processors (20-23) The core has 4 virtual processors (24-27) The core has 4 virtual processors (28-31) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep Mem Memory size: 32640 Megabytes Note that the older processor has 4 virtual CPUs per core, while current processors have 8 per core. Remove ldomsmanager 2.2 and install the 1.2 version The Solaris 11 pkg command is now used to remove the 2.2 version that shipped with Solaris 11: # pkg uninstall ldomsmanager Packages to remove: 1 Create boot environment: No Create backup boot environment: No Services to change: 2 PHASE ACTIONS Removal Phase 130/130 PHASE ITEMS Package State Update Phase 1/1 Package Cache Update Phase 1/1 Image State Update Phase 2/2 Finally, LDoms 1.2 installed via its install script, the same way it was done years ago: # unzip LDoms-1_2-Integration-10.zip # cd LDoms-1_2-Integration-10/Install/ # ./install-ldm Welcome to the LDoms installer. You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. ... ... normal install messages omitted ... The Solaris Security Toolkit applies to Solaris 10, and cannot be used in Solaris 11 (in which several things hardened by the Toolkit are already hardened by default), so answer b in the choice below: You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. Select a security profile from this list: a) Hardened Solaris configuration for LDoms (recommended) b) Standard Solaris configuration c) Your custom-defined Solaris security configuration profile Enter a, b, or c [a]: b ... other install messages omitted for brevity... After install I ensure that the necessary services are enabled, and verify the version of the installed LDoms Manager: # svcs ldmd STATE STIME FMRI online 22:00:36 svc:/ldoms/ldmd:default # svcs vntsd STATE STIME FMRI disabled Aug_19 svc:/ldoms/vntsd:default # ldm -V Logical Domain Manager (v 1.2-debug) Hypervisor control protocol v 1.3 Using Hypervisor MD v 1.1 System PROM: Hypervisor v. 1.7.3. @(#)Hypervisor 1.7.3.c 2010/07/09 15:14\015 OpenBoot v. 4.30.4. @(#)OBP 4.30.4.b 2010/07/09 13:48 Set up control domain and domain services At this point we have a functioning LDoms 1.2 environment that can be configured in the usual fashion. One difference is that LDoms 1.2 behavior had 'delayed configuration mode (as expected) during initial configuration before rebooting the control domain. Another minor difference with a Solaris 11 control domain is that you define virtual switches using the 'vanity name' of the network interface, rather than the hardware driver name as in Solaris 10. # ldm list ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Configuration and resource information is displayed for the configuration under construction; not the current active configuration. The configuration being constructed will only take effect after it is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-c-- SP 32 32640M 3.2% 4d 2h 50m # ldm add-vdiskserver primary-vds0 primary # ldm add-vconscon port-range=5000-5100 primary-vcc0 primary # ldm add-vswitch net-dev=net0 primary-vsw0 primary # ldm set-mau 2 primary # ldm set-vcpu 8 primary # ldm set-memory 4g primary # ldm add-config initial # ldm list-spconfig factory-default initial [current] That's it, really. After reboot, we are ready to install guest domains. Summary - new wine in old bottles This example shows that (new) Solaris 11 can be installed on (old) T2000 servers and used as a control domain. The main activity is to remove the preinstalled Oracle VM Server for 2.2 and install Logical Domains 1.2 - the last version of LDoms to support T1-processor systems. I tested Solaris 10 and Solaris 11 guest domains running on this server and they worked without any surprises. This is a viable way to get further into Solaris 11 adoption, even on older T-series equipment.

  Read the article

• Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed!

  - by meder

  I restarted my VPS box ( manually/hard restart ) and ever since, mysql fails to start for whatever reason. I did a tail /var/log/syslog and I get this: Feb 20 11:49:33 kyrgyznews mysqld[11461]: ) ;InnoDB: End of page dump 575 Feb 20 11:49:33 kyrgyznews mysqld[11461]: 110220 11:49:33 InnoDB: Page checksum 1045788239, prior-to-4.0.14-form checksum 236985105 576 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: stored checksum 1178062585, prior-to-4.0.14-form stored checksum 236985105 577 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page lsn 0 10651, low 4 bytes of lsn at page end 10651 578 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page number (if stored to page already) 3, 579 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: space id (if created with >= MySQL-4.1.1 and stored already) 0 580 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Database page corruption on disk or a failed 581 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: file read of page 3. 582 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: You may have to recover from a backup. 583 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: It is also possible that your operating 584 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: system has corrupted its own file cache 585 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: and rebooting your computer removes the 586 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: error. 587 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: If the corrupt page is an index page 588 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: you can also try to fix the corruption 589 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: by dumping, dropping, and reimporting 590 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: the corrupt table. You can use CHECK 591 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: TABLE to scan your table for corruption. 592 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: See also InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html 593 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: about forcing recovery. 594 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Ending processing because of a corrupt database page. 595 Feb 20 11:49:33 kyrgyznews mysqld_safe[11469]: ended 596 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 0 processes alive and '/usr/bin/mysqladmin --defaults-file=/etc/mysql/debian.cnf ping' resulted in 597 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: ^G/usr/bin/mysqladmin: connect to server at 'localhost' failed 598 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: error: 'Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)' 599 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: Check that mysqld is running and that the socket: '/var/run/mysqld/mysqld.sock' exists! 600 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 601 Feb 20 11:49:56 kyrgyznews mysqld_safe[13437]: started 602 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: The log sequence number in ibdata files does not match 603 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: the log sequence number in the ib_logfiles! 604 Feb 20 11:49:56 kyrgyznews mysqld[13440]: 110220 11:49:56 InnoDB: Database was not shut down normally! 605 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Starting crash recovery. 606 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Reading tablespace information from the .ibd files... 607 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Restoring possible half-written data pages from the doublewrite 608 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: buffer... 609 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Database page corruption on disk or a failed 610 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: file read of page 3. 611 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: You may have to recover from a backup. I have looked at the page it referenced, http://dev.mysql.com/doc/refman/5.0/en/forcing-innodb-recovery.html, but before messing with any settings I was wondering what experienced DBAs would suggest doing? Is there any harm in forcing the recovery? PS - I did not make any updates to mysql. Version is mysql Ver 14.12 Distrib 5.0.51a, for debian-linux-gnu (i486) using readline 5.2.

  Read the article

• Computer makes hissing noise, turns off after few seconds

  - by Kaustubh P

  I have a problem similar to the questions posted here and here. This is my config: Asus M3N78-EM, with AMD Phenom X3 720 2800 Black Edition, 4GB Transcend DDR2 RAM, Nvidia 9400GT. HD is a 160 GB IDE, and a LG IDE DVD-ROM. The power button is a bit off, I have removed the cover of the switch, and the only way it turns on is just giving the "stick" under the cover a gentle press. It turns on sometimes, and at other times, I have to cut-off the power from the PSU, and try again. I will describe my problem in as detail as possible, please bear with me: The problem has started in the last week, a few months after I changed the to the powerswitch arrangement as described above. The PC makes a hissing noise, and I wasn't able to pin-point the noise source, because of the various other fans. At first, removing the HD, rebooting w/o the HD, turning it off, reconnecting and booting made the problem go away. But of late, it doesn't happen. As suggested in the other questions, I tried reducing the load by disconnecting both the IDE drives, and the problem (noise + turn-off) still occurs. I also connected another 80G IDE HD,today morning, adn it still made that noise, and turned off. I also opened up the PSU, but I couldn't see any fault in that, I tried rotating the fan by blowing into the blades, and with my fingers, but the hissing noise didn't come from there. Or maybe the speed wasn't enough to evoke that noise. A few weeks ago: I had cleaned the Cabinet and had repasted the processor and its fan using some thermal paste. Could that be at fault? I also used a vacuum to blow the dust out of the PSU, could the power have been too much, to maybe offset the fan or something? A label on the PSU says it uses a ball-bearing fan. That only leaves me with the Processor fan and the processor itself. I didn't try removing the processor fan and processor from the motherboard, and then turning the PC on, fearing damage. Will doing so cause any damage? What can I do to localize and pin-point the problem? Also, after a few tries, the Computer starts up. Sometimes it turns of within 2 seconds, sometimes after the POST. Once it turned off at the grub. Another time it booted completely and then turned off. The only way to ensure that the PC wont turn off, is if the hissing noise stops. EDIT: I suspect it to be the Processor/Processor fan, owing to the source of noise. All the config, except for the Cabinet, is just over a year old. EDIT2: I also just remembered, that I had set the "On-power resume" to turn on, i.e. If I supply he PC with power, it will turn itself on, w/o me needing to press the switch. I had done that to workaround the faulty power-switch, as noted above. EDIT3: I calculated the power my system needs, from the antec site, and I just arrived at 292W

  Read the article

• Centos 7. Freeradius fails to start on boot

  - by Alex

  I was messing around with FreeRADIUS and MySQL (MariaDB) and it seems FreeRADIUS service can't start properly on startup. But it starts fine using root user or in debug mode (radiusd -X) and works just fine! Debug mode shows no errors. systemctl command shows that radiusd.service has failed to start. /var/log/messages output: Aug 21 15:52:29 nexus-test systemd: Starting The Apache HTTP Server... Aug 21 15:52:29 nexus-test systemd: Starting MariaDB database server... Aug 21 15:52:29 nexus-test systemd: Starting FreeRADIUS high performance RADIUS server.... Aug 21 15:52:29 nexus-test systemd: Started OpenSSH server daemon. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Logging to '/var/log/mariadb/mariadb.log'. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql Aug 21 15:52:30 nexus-test systemd: Started Postfix Mail Transport Agent. Aug 21 15:52:30 nexus-test avahi-daemon[604]: Registering new address record for fe80::250:56ff:fe85:e4af on eth0.*. Aug 21 15:52:30 nexus-test systemd: radiusd.service: control process exited, code=exited status=1 Aug 21 15:52:30 nexus-test systemd: Failed to start FreeRADIUS high performance RADIUS server.. Aug 21 15:52:30 nexus-test systemd: Unit radiusd.service entered failed state. Aug 21 15:52:31 nexus-test kdumpctl: kexec: loaded kdump kernel Aug 21 15:52:31 nexus-test kdumpctl: Starting kdump: [OK] Aug 21 15:52:31 nexus-test systemd: Started Crash recovery kernel arming. Aug 21 15:52:31 nexus-test systemd: Started The Apache HTTP Server. Aug 21 15:52:31 nexus-test systemd: Started MariaDB database server. /var/log/radius/radius.log output: Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Attempting to connect to database "radius" Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Opening additional connection (0) Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Couldn't connect socket to MySQL server radius@localhost:radius Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Mysql error 'Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' (2)' Thu Aug 21 15:24:16 2014 : Error: rlm_sql (sql): Opening connection failed (0) Thu Aug 21 15:24:16 2014 : Error: /etc/raddb/mods-enabled/sql[47]: Instantiation failed for module "sql" After seeing this I tried to replicate the problem, killed mariadb.service and started to run debug mode again. And it spits out the same problem as in the radius.log. I tried disabling iptables and firewalld and rebooting, but no luck: systemctl disable iptables systemctl disable firewalld So maybe the problem is in the process startup order or delay of some kind. Maybe FreeRADIUS's SQL module can't connect to not yet started MariaDB? If it, how can I fix this? In earlier versions of RHEL/CENTOS I know you easily see service start order in like rc.d or stuff, now IDK. I am new to this fancy "systemd", "systemctl", "firewalld" stuff Centos 7 introduced so sorry I'm a little bit confused. Also this new FreeRADIUS 3 structure... PS. MariaDB is enabled on startup, credentials in FR DB configuration are correct A little update: cat /etc/systemd/system/multi-user.target.wants/radiusd.service output: [Unit] Description=FreeRADIUS high performance RADIUS server. After=syslog.target network.target [Service] Type=forking PIDFile=/var/run/radiusd/radiusd.pid ExecStartPre=-/bin/chown -R radiusd.radiusd /var/run/radiusd ExecStartPre=/usr/sbin/radiusd -C ExecStart=/usr/sbin/radiusd -d /etc/raddb ExecReload=/usr/sbin/radiusd -C ExecReload=/bin/kill -HUP $MAINPID [Install] WantedBy=multi-user.target

  Read the article

• Windows XP Video Configuration Issues

  - by Matt

  Recently I had my motherboard burn out on me. Needing the machine for work, I purchased a different motherboard and installed that. Generally a reinstall of windows is good at that point but I am not in a position to do that so I just decided I would live with it for now. When I can log-in, everything works fine, what doesn't is getting to the log-in prompt to begin with. Basically when I first installed the new mobo, every time I rebooted the machine, I would not get the windows login prompt. One of the monitors would receive a signal but the screen would be black. Moving the mouse would not show the cursor and hitting the up arrow key and typing my password and hitting enter (which will normally log you in without mouse) wouldn't change anything. I would then change the monitor configuration around (2 lcd's and a crt) and reboot and at least one of the monitors would work and display the login prompt. I could then go into display properties and turn on the other monitors. However if I rebooted again, I would get the black screen on one monitor again. I would then have to change the configuration again to one not used before and I could re-do the manual setup at that point. I think windows saves the configurations so I had to keep giving it new ones. Needless to say I've been trying to not turn off my machine. Early this week I actually got the prompt to come up without playing musical monitors. Thinking everything was getting better, I found no harm in rebooting to install the latest windows updates. Boy was I wrong. Now no matter what I do I can't get a windows log-in prompt to display. I've tried almost every conceivable combination. The new mobo has onboard video so I set that in the bios (yea bios screen always displays fine, its not until windows boots that there is a problem) to be the primary video. Still no luck. I have two other graphics cards in the machine which I'm using. Tried all kinds of configurations between those and on-board but still get this black screen of death. I read somewhere that deleting the video drivers would reset the configurations. I logged into safe mode (which works on one monitor), and uninstalled the display drivers. Still no luck and when I booted back into safe mode, it wanted to install new hardware and the display adapters weren't there as expected. Anyone have any ideas? A fresh install would be a pain and I might be getting my old board back from RMA soon so not sure I want to go through with that just yet. Only thing I can think of is to continue to try other combinations like physically removing the graphics cards. They are both EVGA 8600 cards and the windows boot screen does display fwiw.

  Read the article

• Nvidia drivers don't work with mainline kernel

  - by dutchie

  I want to try some of the new features in the btrfs filesystem, and to do that I need to use a newer kernel than is included in Ubuntu 12.04. To do that, I have installed linux-headers-3.4.0-030400_3.4.0-030400.201205210521_all.deb, linux-headers-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb, and linux-image-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb from the mainline kernel download here. However, on rebooting into the 3.4 kernel, my desktop is stuck at a very low resolution and I cannot increase it to the full. This did happen when I first installed, but a simple install of the nvidia-current package got everything working nicely with my GTX570 card. There were appear to be some DKMS errors when I installed the kernel, and they indicated I should look at /var/lib/dkms/nvidia-current/295.40/build/make.log: josh@sirius:~/Downloads$ sudo dpkg -i linux-*.deb Selecting previously unselected package linux-headers-3.4.0-030400. (Reading database ... 309400 files and directories currently installed.) Unpacking linux-headers-3.4.0-030400 (from linux-headers-3.4.0-030400_3.4.0-030400.201205210521_all.deb) ... Selecting previously unselected package linux-headers-3.4.0-030400-generic. Unpacking linux-headers-3.4.0-030400-generic (from linux-headers-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb) ... Selecting previously unselected package linux-image-3.4.0-030400-generic. Unpacking linux-image-3.4.0-030400-generic (from linux-image-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb) ... Done. Setting up linux-headers-3.4.0-030400 (3.4.0-030400.201205210521) ... Setting up linux-headers-3.4.0-030400-generic (3.4.0-030400.201205210521) ... Examining /etc/kernel/header_postinst.d. run-parts: executing /etc/kernel/header_postinst.d/dkms 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic ERROR (dkms apport): kernel package linux-headers-3.4.0-030400-generic is not supported Error! Bad return status for module build on kernel: 3.4.0-030400-generic (x86_64) Consult /var/lib/dkms/nvidia-current/295.40/build/make.log for more information. Setting up linux-image-3.4.0-030400-generic (3.4.0-030400.201205210521) ... Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic ERROR (dkms apport): kernel package linux-headers-3.4.0-030400-generic is not supported Error! Bad return status for module build on kernel: 3.4.0-030400-generic (x86_64) Consult /var/lib/dkms/nvidia-current/295.40/build/make.log for more information. run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic update-initramfs: Generating /boot/initrd.img-3.4.0-030400-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.4.0-030400-generic Found initrd image: /boot/initrd.img-3.4.0-030400-generic Found linux image: /boot/vmlinuz-3.2.0-24-generic Found initrd image: /boot/initrd.img-3.2.0-24-generic Found memtest86+ image: /memtest86+.bin Found Ubuntu 12.04 LTS (12.04) on /dev/sda1 Found Windows 7 (loader) on /dev/sda2 Found Windows 7 (loader) on /dev/sda3 done /var/lib/dkms/nvidia-current/295.40/build/make.log: DKMS make.log for nvidia-current-295.40 for kernel 3.4.0-030400-generic (x86_64) Thu Jun 7 00:58:39 BST 2012 NVIDIA: calling KBUILD... test -e include/generated/autoconf.h -a -e include/config/auto.conf || ( \ echo; \ echo " ERROR: Kernel configuration is invalid."; \ echo " include/generated/autoconf.h or include/config/auto.conf are missing.";\ echo " Run 'make oldconfig && make prepare' on kernel src to fix it."; \ echo; \ /bin/false) mkdir -p /var/lib/dkms/nvidia-current/295.40/build/.tmp_versions ; rm -f /var/lib/dkms/nvidia-current/295.40/build/.tmp_versions/* make -f scripts/Makefile.build obj=/var/lib/dkms/nvidia-current/295.40/build cc -Wp,-MD,/var/lib/dkms/nvidia-current/295.40/build/.nv.o.d -nostdinc -isystem /usr/lib/gcc/x86_64-linux-gnu/4.6/include -I/usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include -Iarch/x86/include/generated -Iinclude -include /usr/src/linux-headers-3.4.0-030400-generic/include/linux/kconfig.h -D__KERNEL__ -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implicit-function-declaration -Wno-format-security -fno-delete-null-pointer-checks -O2 -m64 -mtune=generic -mno-red-zone -mcmodel=kernel -funit-at-a-time -maccumulate-outgoing-args -fstack-protector -DCONFIG_AS_CFI=1 -DCONFIG_AS_CFI_SIGNAL_FRAME=1 -DCONFIG_AS_CFI_SECTIONS=1 -DCONFIG_AS_FXSAVEQ=1 -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -mno-sse2 -mno-3dnow -mno-avx -Wframe-larger-than=1024 -Wno-unused-but-set-variable -fno-omit-frame-pointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-statement -Wno-pointer-sign -fno-strict-overflow -fconserve-stack -DCC_HAVE_ASM_GOTO -I/var/lib/dkms/nvidia-current/295.40/build -Wall -MD -Wsign-compare -Wno-cast-qual -Wno-error -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"295.40\" -Wno-unused-function -Wuninitialized -mno-red-zone -mcmodel=kernel -UDEBUG -U_DEBUG -DNDEBUG -DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(nv)" -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -c -o /var/lib/dkms/nvidia-current/295.40/build/.tmp_nv.o /var/lib/dkms/nvidia-current/295.40/build/nv.c In file included from include/linux/kernel.h:19:0, from include/linux/sched.h:55, from include/linux/utsname.h:35, from /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h:38, from /var/lib/dkms/nvidia-current/295.40/build/nv.c:13: include/linux/bitops.h: In function ‘hweight_long’: include/linux/bitops.h:66:41: warning: signed and unsigned type in conditional expression [-Wsign-compare] In file included from /usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include/asm/uaccess.h:577:0, from include/linux/poll.h:14, from /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h:97, from /var/lib/dkms/nvidia-current/295.40/build/nv.c:13: /usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include/asm/uaccess_64.h: In function ‘copy_from_user’: /usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include/asm/uaccess_64.h:53:6: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] In file included from /var/lib/dkms/nvidia-current/295.40/build/nv.c:13:0: /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h: At top level: /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h:114:75: fatal error: asm/system.h: No such file or directory compilation terminated. make[3]: *** [/var/lib/dkms/nvidia-current/295.40/build/nv.o] Error 1 make[2]: *** [_module_/var/lib/dkms/nvidia-current/295.40/build] Error 2 NVIDIA: left KBUILD. nvidia.ko failed to build! make[1]: *** [module] Error 1 make: *** [module] Error 2

  Read the article

• Why would VMWare to go defunct? How to recover from/prevent it?

  - by Josh

  I am running VMWare Server 2.0.2 (Build 203138) on a dual core Intel i5 with Ubuntu Server 10.04 LTS system (kernel 2.6.32-22-server #33-Ubuntu SMP). Disk Subsystem is a software RAID5 array. The system has been set up for a little over a week. For the past 5 days I have been running at leat 3 VMs (Linux and a variety of Windows OSes) with no issues whatsoever. But while I was installing Linux onto a new VM, suddenly all VMs became unresponsive, including the one I was installing to. I could not log in to the VMWare Management Interface, and the system was somewhat unresponsive via SSH. When I looked at top, I saw: top - 16:14:51 up 6 days, 1:49, 8 users, load average: 24.29, 24.33 17.54 Tasks: 203 total, 7 running, 195 sleeping, 0 stopped, 1 zombie Cpu(s): 0.2%us, 25.6%sy, 0.0%ni, 74.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8056656k total, 5927580k used, 2129076k free, 20320k buffers Swap: 7811064k total, 240216k used, 7570848k free, 5045884k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 21549 root 39 19 0 0 0 Z 100 0.0 15:02.44 [vmware-vmx] <defunct> 2115 root 20 0 0 0 0 S 1 0.0 170:32.08 [vmware-rtc] 2231 root 21 1 1494m 126m 100m S 1 1.6 892:58.05 /usr/lib/vmware/bin/vmware-vmx -# product=2; 2280 jnet 20 0 19320 1164 800 R 0 0.0 30:04.55 top 12236 root 20 0 833m 41m 34m S 0 0.5 88:34.24 /usr/lib/vmware/bin/vmware-vmx -# product=2; 1 root 20 0 23704 1476 920 S 0 0.0 0:00.80 /sbin/init 2 root 20 0 0 0 0 S 0 0.0 0:00.01 [kthreadd] 3 root RT 0 0 0 0 S 0 0.0 0:00.00 [migration/0] 4 root 20 0 0 0 0 S 0 0.0 0:00.84 [ksoftirqd/0] 5 root RT 0 0 0 0 S 0 0.0 0:00.00 [watchdog/0] 6 root RT 0 0 0 0 S 0 0.0 0:00.00 [migration/1] The VMWare process for the virtual machine I was installing into became a zombie. Yet, it was still consuming 100% of the CPU time on one of the cores, and I couldn't reach it or any other virtual machines. (I was logged in to one virtual machine over SSH, another via X11, and a third via VNC. All three connections died). When I ran ps -ef and similar commands, I found that the defunct vmware-vmx process had it's parent PID set to init (1). I also used lsof -p 21549 and found that the defunct process had no open files. Yet it was using 100% of CPU time... I was unable to kill any vmware-vmx processes, including the defunct one, even with kill -9. As a last resort to resolve the situation I tried to reboot the box, however shutdown, halt, reboot, and init 6 all failed to reboot/shutdown, even when given appropriate --force settings. ControlAltDel produced a message about rebooting on the console, but the system would not reboot. I had to hard power-cycle the box to resolve the situation. (See my other question, Should I worry about the integrity of my linux software RAID5 after a crash or kernel panic?) What would cause a scenario like this? What else could I have done to resolve it besides a hard reboot? What can I do to prevent such a situation in the future?

  Read the article

• I Clobbered a Leopard with a Window Last Night

  - by D'Arcy Lussier

  I’ve had my 15” Mac Book Pro for a little over a year now, and its hands-down the best laptop I’ve ever owned…hardware wise. And I tried, I really really tried, to like OSX. I even bought Parallels so I could run Windows 7 and all my development tools while still trying to live in an OSX world. But in the end, I missed Windows too much. There were just too many shortcomings with OSX that kept me from being productive. For one thing, Office for Mac is *not* Office for Windows. The applications are written by different teams, and Excel on the Mac is just different enough to be painful. The VM experience was adequate, but my MBP would heat up like crazy when running it and the experience trying to get Windows apps to interact with an OSX file system was awkward. And I found I was in the VM more than I thought I’d be. iMovie is not as easy to use for doing simple movie editing as Windows Movie Maker. There’s no free blog editing software for OSX that’s on par with Windows Live Writer. And really, all I was using OSX for was Twitter (which I can use a Windows client for) and web browsing (also something Windows can provide obviously). So I had to ask myself – why am I forcing myself to use an operating system I don’t like, on a laptop that can support Windows 7? And so I paved my MBP and am happily running Windows 7 on it…and its fantastic! All the good stuff with the hardware is still there with the goodness of Win 7. Happy happy. I did run into some snags doing this though, and that’s really what this blog post is about – things to be aware of if you want to install Win 7 directly on your MBP metal. First, Ensure You Have Your Original Mac Install Disk This was a warning my buddy Dylan, who’s been running Win 7 on his MBP for a while now, gave me early on. The reason you need that original disk is that the hardware drivers you need are all located there. Apparently you can’t easily download them, so make sure you have them ahead of time. Second, Forget BootCamp The only reason you need BootCamp is if you still want the option to boot into OSX. If you don’t, then you don’t need BootCamp. In fact, you don’t even need BootCamp to install Win 7. What you *will* need though is a DVD with Win 7 burnt on it. Apple doesn’t support bootable USB drives. Well, actually they do for Mac Book Airs which don’t come with optical drives…but to get it working you’ll need to edit a system file of BootCamp so your make of MBP is included in an XML document, and even then you *still* are using BootCamp meaning you’ll be making an OSX partition. So don’t worry about BootCamp, just burn a Windows 7 disc, put it into the DVD drive, and restart your MBP. Third, Know The Secret Commands So after putting in the Windows 7 DVD and restarting your MBP, you’ll want to hold down the ‘C’ key during boot up. This tells the MBP that it should boot from the DVD drive instead of the hard drive. Interestingly, it appears you don’t have to do this if its the Mac OSX install disc (more on that in a second), but regardless – hold down C and Windows will start the install process. Next up is the partition process. You’ll notice that there’s a partition called ETI or something like that. This has to do with the drive format that Apple uses and how they partition their system drives. What I did – I blew it away! At first I didn’t, but I was told I couldn’t install Windows on the remaining space due to the different drive format. Blowing away the ETI partition (and all other partitions) allowed me to continue the Windows install. *REMEMBER –  No warranty is provided or implied, just telling you what I did and how I got it to work. Ok, so now Windows is installed and I’m rebooting. Everything looks good, but I need drivers! So I put in the OSX install DVD and run the BootCamp assistant which installs all the Windows drivers I need. Fantastic! Oh, I need to restart – no problem. OH NO, PROBLEM! I left the OSX install DVD in the drive and now the MBP wants to boot from the drive and install OSX! I’m not holding down the C key, what the heck?! Ok, well there must be a way to eject this disk…hmm…no physical button on the side…the eject button doesn’t seem to work on the keyboard…no little pin hole to insert something to force the disc out…well what the…?! It turns out, if you want to eject a disc at boot up, you need (and I kid you not) to plug a mouse into the laptop and hold down the right-click button while its booting. This ejected the disc for me. Seriously. Finally, Things You Should Be Aware Of Once you have Windows up and running there’s a few things you need to be aware of, mainly new keyboard shortcuts. For instance, on the Mac keyboard there is no Home, End, PageUp or PageDown. There’s also no obvious way to do something like select large amounts of text (like you would by holding Shift-Home at the end of a line of text for instance). So here’s some shortcuts you need to know: Home – fn + left arrow End – fn + right arrow Select a line of text as you would with the Home key – Shift + fn + left arrow Select a line of text as you would with the End key – Shift + fn + right arrow Page Up – fn + up arrow Page Down – fn + down arrow Also, you’ll notice that the awesome Mac track pad doesn’t respond to taps as clicks. No fear, this is just a setting that needs to be altered in the BootCamp control panel (that controls the Mac Hardware-specific settings within Windows, you can access it easily from the system tray icon) One other thing, battery life seems a bit lower than with OSX, but then again I’m also doing more than Twitter or web browsing on this thing now. Conclusion My laptop runs awesome now that I have Windows 7 on there. It’s obviously up to individual taste, but for me I just didn’t see benefits to living in an OSX world when everything I needed lived in Windows. And also, I finally am back to an operating system that doesn’t require me to eject a USB drive before physically removing it! It’s 2012 folks, how has this not been fixed?! D

  Read the article

• How to diagnose and solve an erratic "HDCP Support Required"?

  - by Jom Orgstrom

  I am playing a digital tv broadcast on Windows Media Center for Windows 7. I built this system so it works with HDCP, and in fact I have been able to watch tv and bluray before with this same computer. However, I suddenly started getting an "HDCP Support Required" error from WMC. The entire message is as follows: HDCP Support Required High-bandwidth Digital Content Protection (HDCP) may not be supported by the current video card. Use an HDCP-compliant display, video card, and video driver. Or, connect using an analog connection such as component or VGA. Relevant specs are: CPU: Ivy Bridge Core i7-3770 Motherboard: Asus P8H77-I Memory: 16GB DDR3-1600 Graphics: Radeon HD 7850 (Driver by AMD, version 8.982.0.0 built on 2012/07/27) Display: Acer P243w connected by HDMI Sound: Roland Quad-Capture (It complains even when I use the bundled VIA HD Audio) TV Tuner: I-O Data GV-MC7/HZ3 OS: Windows 7 Professional SP1, Windows Update enabled. All patched and up to date. As you can see, there is nothing weird or old about my setup. I am also not doing anything strange, not doing any overclocking, weird system changes and so on. One thing that does happen from time to time, is that the display goes black for a few seconds (sometimes when watching media contents, sometimes when just using photoshop or Visual Studio). This happened with my previous setup as well, so I'd be inclined to think it is a display or cable issue (apart from the BD drive, these are the only things I kept from my previous setup to this one). But being a digital transfer, as far as I know, these things either work or not. Never erratically or with decreased quality. The thing is that sometimes I can watch the TV, sometimes not. This happens with recorded programs as well, so it's not a per-program thing. Sometimes rebooting helps, sometimes it doesn't. Sometimes unplugging and plugging back the HDMI connector helps, sometimes it doesn't. Sometimes doing so doesn't even turn the screen back on, so I have to reboot. Unfortunately, WMC's error message is quite unhelpful. I'd like to know exactly where the problem is, so I can solve it. I don't want to buy a brand new display just to then find out it was a registry setting that was misconfigured. I've tried looking at the system event viewer, but these errors don't show up at all in there. Other people who have this problem seem to have a setup that is not HDCP compliant, so I turn to you guys here. Anybody knows how to diagnose this problem? Edit: So I got the Cyberlink Blu-ray disc advisor. I ran it and told me everything was okay, except for the Video Connection Type, which showed as "Digital (without HDCP)". I then proceeded to unplug the power cable from the monitor, plugged it in again, ran the tool again, and now it's "Digital (with HDCP)". Needless to say, I can watch my TV and recorded programs on WMP again. I'm guessing that at some point, something may be slightly wrong with the HDCP setup, and Windows decides to reset the entire content protection path (which leads to the screen blanking out). Usually the reset succeeds, but sometimes it doesn't, so Windows defaults to turning HDCP off. There's no way to turn it back on, except by doing a hard reset of the display. I really want to know what the exact error was, so I can fix it. Is it the cable? is it the display? is it the video card? the driver? Also, is there any other way to try and turn HDCP on again without having to hard reset the display? Oh, questions, questions...

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• Lustre - issues with simple setup

  - by ethrbunny

  Issue: I'm trying to assess the (possible) use of Lustre for our group. To this end I've been trying to create a simple system to explore the nuances. I can't seem to get past the 'llmount.sh' test with any degree of success. What I've done: Each system (throwaway PCs with 70Gb HD, 2Gb RAM) is formatted with CentOS 6.2. I then update everything and install the Lustre kernel from downloads.whamcloud.com and add on the various (appropriate) lustre and e2fs RPM files. Systems are rebooted and tested with 'llmount.sh' (and then cleared with 'llmountcleanup.sh'). All is well to this point. First I create an MDS/MDT system via: /usr/sbin/mkfs.lustre --mgs --mdt --fsname=lustre --device-size=200000 --param sys.timeout=20 --mountfsoptions=errors=remount-ro,user_xattr,acl --param lov.stripesize=1048576 --param lov.stripecount=0 --param mdt.identity_upcall=/usr/sbin/l_getidentity --backfstype ldiskfs --reformat /tmp/lustre-mdt1 and then mkdir -p /mnt/mds1 mount -t lustre -o loop,user_xattr,acl /tmp/lustre-mdt1 /mnt/mds1 Next I take 3 systems and create a 2Gb loop mount via: /usr/sbin/mkfs.lustre --ost --fsname=lustre --device-size=200000 --param sys.timeout=20 --mgsnode=lustre_MDS0@tcp --backfstype ldiskfs --reformat /tmp/lustre-ost1 mkdir -p /mnt/ost1 mount -t lustre -o loop /tmp/lustre-ost1 /mnt/ost1 The logs on the MDT box show the OSS boxes connecting up. All appears ok. Last I create a client and attach to the MDT box: mkdir -p /mnt/lustre mount -t lustre -o user_xattr,acl,flock luster_MDS0@tcp:/lustre /mnt/lustre Again, the log on the MDT box shows the client connection. Appears to be successful. Here's where the issues (appear to) start. If I do a 'df -h' on the client it hangs after showing the system drives. If I attempt to create files (via 'dd') on the lustre mount the session hangs and the job can't be killed. Rebooting the client is the only solution. If I do a 'lctl dl' from the client it shows that only 2/3 OST boxes are found and 'UP'. [root@lfsclient0 etc]# lctl dl 0 UP mgc MGC10.127.24.42@tcp 282d249f-fcb2-b90f-8c4e-2f1415485410 5 1 UP lov lustre-clilov-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 2 UP lmv lustre-clilmv-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 3 UP mdc lustre-MDT0000-mdc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 4 UP osc lustre-OST0000-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 5 UP osc lustre-OST0003-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 Doing a 'lfs df' from the client shows: [root@lfsclient0 etc]# lfs df UUID 1K-blocks Used Available Use% Mounted on lustre-MDT0000_UUID 149944 16900 123044 12% /mnt/lustre[MDT:0] OST0000 : inactive device OST0001 : Resource temporarily unavailable OST0002 : Resource temporarily unavailable lustre-OST0003_UUID 187464 24764 152636 14% /mnt/lustre[OST:3] filesystem summary: 187464 24764 152636 14% /mnt/lustre Given that each OSS box has a 2Gb (loop) mount I would expect to see this reflected in available size. There are no errors on the MDS/MDT box to indicate that multiple OSS/OST boxes have been lost. EDIT: each system has all other systems defined in /etc/hosts and entries in iptables to provide access. SO: I'm clearly making several mistakes. Any pointers as to where to start correcting them?

  Read the article

• Azure Task Scheduling Options

  - by charlie.mott

  Currently, the Azure PaaS does not offer a distributed\resilient task scheduling service.  If you do want to host a task scheduling product\solution off-premise (and ideally use Azure), what are your options? PaaS Option 1: Worker Roles Use a worker role to schedule and execute actions at specific time periods.  There are a few frameworks available to assist with this: http://azuretoolkit.codeplex.com https://github.com/Lokad/lokad-cloud/wiki/TaskScheduler http://blog.smarx.com/posts/building-a-task-scheduler-in-windows-azure - This addresses a slightly different set of requirements. It’s a more dynamic approach for queuing up tasks, but not repeatable tasks (e.g. daily). I found the Azure Toolkit option the most simple to implement.  Step 1 : Create a domain entity implementing IJob for each job to schedule.  In this sample, I asynchronously call a WCF service method. 1: namespace Acme.WorkerRole.Jobs 2: { 3: using AzureToolkit; 4: using ScheduledTasksService; 5: 6: public class UploadEmployeesJob : IJob 7: { 8: public void Run() 9: { 10: // Call Tasks Service 11: var client = new ScheduledTasksServiceClient("BasicHttpBinding_IScheduledTasksService"); 12: client.UploadEmployees(); 13: client.Close(); 14: } 15: } 16: } Step 2 : In the worker role run method, add the jobs to the toolkit engine. 1: namespace Acme.WorkerRole 2: { 3: using AzureToolkit.Engine; 4: using Jobs; 5:   6: public class WorkerRole : WorkerRoleEntryPoint 7: { 8: public override void Run() 9: { 10: var engine = new CloudEngine(); 11:   12: // Add Scheduled Jobs (using CronJob syntax - see http://www.adminschoice.com/crontab-quick-reference). 13:   14: // 1. Upload Employee job - 8.00 PM every weekday (Mon-Fri) 15: engine.WithJobScheduler().ScheduleJob<UploadEmployeesJob>(c => { c.CronSchedule = "0 20 * * 1-5"; }); 16: // 2. Purge Data job - 10 AM every Saturday 17: engine.WithJobScheduler().ScheduleJob<PurgeDataJob>(c => { c.CronSchedule = "0 10 * * 6"; }); 18: // 3. Process Exceptions job - Every 5 minutes 19: engine.WithJobScheduler().ScheduleJob<ProcessExceptionsJob>(c => { c.CronSchedule = "*/5 * * * *"; }); 20:   21: engine.Run(); 22: base.Run(); 23: } 24: } 25: } Pros Cons Azure Toolkit option is simple to implement. For the AzureToolkit option, you are limited to a single worker role.  Otherwise, the jobs will be executed multiple times, once for each worker role instance.   Paying for a continuously running worker role, even if it just processes a single job once a week.  If you only have a few scheduled tasks to run calling asynchronous services hosted in different web roles, an extra small worker role likely to be sufficient.  However, for an extra small worker role this still costs $14.40/month (03/09/2012). Option 2: Use Scheduled Task on Azure Web Role calling a console app Setup a Windows Scheduled Task on the Azure Web Role. This calls a console application that calls the WCF service methods that run the task actions. This design is described here: http://www.ronaldwidha.net/2011/02/23/cron-job-on-azure-using-scheduled-task-on-a-web-role-to-replace-azure-worker-role-for-background-job/ http://www.voiceoftech.com/swhitley/index.php/2011/07/windows-azure-task-scheduler/ http://devlicio.us/blogs/vinull/archive/2011/10/23/moving-to-azure-worker-roles-for-nothing-and-tasks-for-free.aspx Pros Cons Fairly easy to implement. Supportability - I RDC’ed onto the Azure server and stopped the scheduled task. I then rebooted the machine and the task was re-started. I also tried deleting the task and rebooting, the same thing occurred. The only way to permanently guarantee that a task is disabled is to do a fresh deployment. I think this is a major supportability concern.   Saleability - multiple instances would trigger multiple tasks. You can only have one instance for the scheduled task web role. The guidance implements setup of the scheduled task as part of a web role instance. But if you have more than one instance in a web role, the task will be triggered multiple times for each scheduled action (once per machine). Workaround: If we wanted to use scheduled tasks for another client with a saleable WCF service, then we could include the console & tasks scripts in a separate web role (e.g. a empty WCF service with no real purpose to it). SaaS Option 3: Azure Marketplace I thought that someone might be offering this type of service via the Azure marketplace. At the point of writing this blog post, I did not find anyone doing so. https://datamarket.azure.com/ Pros Cons   Nobody currently offers this on the Azure Marketplace. Option 4: Online Job Scheduling Service Provider There are plenty of online providers that offer this type of service on a pay-as-you-go approach.  Some of these are free for small usage.   Many of these providers are listed here: http://en.wikipedia.org/wiki/Webcron Pros Cons No bespoke development for scheduler. Reliance on third party. IaaS Option 5: Setup Scheduling Software on Azure IaaS VM’s One of job scheduling software offerings could be installed and configured on Azure VM’s.  A list of software options is listed here: http://en.wikipedia.org/wiki/List_of_job_scheduler_software Pros Cons Enterprise distributed\resilient task scheduling service VM Setup and maintenance   Software Licence Costs Option 6: VM Gallery A the time of writing this blog post, I did not spot a VM in the gallery that included pre-installation of any of the above software options. Pros Cons   No current VM template. Summary For my current project that had a small handful of tasks to schedule with a limited project budget I chose option 1 (a worker role using the Azure Toolkit to schedule tasks).  If I was building an enterprise scale solution for the future, options 4 and 5 are currently worthy of consideration. Hopefully, Microsoft will include tasks scheduling in the future as part of their PaaS offerings.

  Read the article

• volume group disappeared after xfs_check run

  - by John P

  EDIT** I have a volume group consisting of 5 RAID1 devices grouped together into a lvm and formatted with xfs. The 5th RAID device lost its RAID config (cat /proc/mdstat does not show anything). The two drives are still present (sdj and sdk), but they have no partitions. The LVM appeared to be happily using sdj up until recently. (doing a pvscan showed the first 4 RAID1 devices + /dev/sdj) I removed the LVM from the fstab, rebooted, then ran xfs_check on the LV. It ran for about half an hour, then stopped with an error. I tried rebooting again, and this time when it came up, the logical volume was no longer there. It is now looking for /dev/md5, which is gone (though it had been using /dev/sdj earlier). /dev/sdj was having read errors, but after replacing the SATA cable, those went away, so the drive appears to be fine for now. Can I modify the /etc/lvm/backup/dedvol, change the device to /dev/sdj and do a vgcfgrestore? I could try doing a pvcreate --uuid KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ /dev/sdj to make it recognize it, but I'm afraid that would erase the data on the drive UPDATE: just changing the pv to point to /dev/sdj did not work vgcfgrestore --file /etc/lvm/backup/dedvol dedvol Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Cannot restore Volume Group dedvol with 1 PVs marked as missing. Restore failed. pvscan /dev/sdj: read failed after 0 of 4096 at 0: Input/output error Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. PV /dev/sdd2 VG VolGroup00 lvm2 [74.41 GB / 0 free] PV /dev/md2 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md3 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md0 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md4 VG dedvol lvm2 [931.51 GB / 0 free] PV unknown device VG dedvol lvm2 [1.82 TB / 63.05 GB free] Total: 6 [5.53 TB] / in use: 6 [5.53 TB] / in no VG: 0 [0 ] vgscan Reading all physical volumes. This may take a while... /dev/sdj: read failed after 0 of 4096 at 0: Input/output error /dev/sdj: read failed after 0 of 4096 at 2000398843904: Input/output error Found volume group "VolGroup00" using metadata type lvm2 Found volume group "dedvol" using metadata type lvm2 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 5 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 5 Act PV 5 VG Size 5.46 TB PE Size 4.00 MB Total PE 1430796 Alloc PE / Size 1414656 / 5.40 TB Free PE / Size 16140 / 63.05 GB VG UUID o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246 dedvol { id = "o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246" seqno = 10 status = ["RESIZEABLE", "READ", "WRITE"] flags = [] extent_size = 8192 # 4 Megabytes max_lv = 0 max_pv = 0 physical_volumes { pv0 { id = "Msiee7-Zovu-VSJ3-Y2hR-uBVd-6PaT-Ho9v95" device = "/dev/md2" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv1 { id = "ZittCN-0x6L-cOsW-v1v4-atVN-fEWF-e3lqUe" device = "/dev/md3" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv2 { id = "NRNo0w-kgGr-dUxA-mWnl-bU5v-Wld0-XeKVLD" device = "/dev/md0" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv3 { id = "2EfLFr-JcRe-MusW-mfAs-WCct-u4iV-W0pmG3" device = "/dev/md4" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv4 { id = "KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ" device = "/dev/md5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 3907028992 # 1.81935 Terabytes pe_start = 384 pe_count = 476932 # 1.81935 Terabytes } }

  Read the article

• Nginx Multiple Domains

  - by showFocus

  I am trying to add a second virtual host to nginx. When i go to the new domain it redirects to the old one. I have tried restarting Nginx, rebooting the server. Has anyone come across this before, care to share? File: nginx.conf ### user www-data www-data; worker_processes 4; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 5; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; include /usr/local/nginx/sites-enabled/*; } File: ../sites-enabled/domain1.co.uk server { listen 80; server_name www.domain1.co.uk; rewrite ^/(.*) http://domain1.co.uk/$1 permanent; } server { listen 80; server_name domain1.co.uk; access_log /home/me/public_html/domain1.co.uk/log/access.log; error_log /home/me/public_html/domain1.co.uk/log/error.log; location / { root /home/me/public_html/domain1.co.uk/public/; index index.php index.html; # WordPress supercache & permalinks. include /usr/local/nginx/conf/wordpress_params.super_cache; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/me/public_html/domain1.co.uk/public/$fastcgi_script_name; } } File: ../sites-enabled/domain2.co.uk server { listen 80; server_name www.domain2.co.uk; rewrite ^/(.*) http://domain2.co.uk/$1 permanent; } server { listen 80; server_name domain2.co.uk; access_log /home/me/public_html/domain2.co.uk/log/access.log; error_log /home/me/public_html/domain2.co.uk/log/error.log; location / { root /home/me/public_html/domain2.co.uk/public/; index index.php index.html; # Basic version of WordPress parameters, supporting nice permalinks. # include /usr/local/nginx/conf/wordpress_params.regular; # Advanced version of WordPress parameters supporting nice permalinks and WP Super Cache plugin include /usr/local/nginx/conf/wordpress_params.super_cache; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/me/public_html/domain2/public/$fastcgi_script_name; } }

  Read the article

< Previous Page | 31 32 33 34 35 36 37  | Next Page >