Search Results

Search found 913 results on 37 pages for 'rebooting'.

Page 34/37 | < Previous Page | 30 31 32 33 34 35 36 37  | Next Page >

• Areca 1280ml RAID6 volume set failed

  - by Richard

  Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I continue, here are the specs: Dedicated Server Machine Areca 1280ml RAID controller, Firmware 1.49 12x Samsung 1TB HDDs We configured one RAID6-set with 10 discs that contains one logical volume. We have two hot spares in the system. Today one HDD failed. This happens from time to time, so we replaced it. Upon rebuilding a second disc failed. Normally this is no fun. We stopped heavy IO-operations to ensure a stable RAID rebuild. Sadly the hot-spare disc failed while rebuilding and the whole thing stopped. Now we have the following situation: The controller says that the raid set is rebuilding The controller says that the volume failed It is a RAID 6 system and two discs failed, so the data has to be intact, but we cannot bring the volume online again to access the data. While searching we found the following leads. I don't know whether they are good or bad: Mirroring all the discs to a second set of drives. So we would have the possibility to try different things without loosing more than we already have. Trying to rebuild the array in R-Studio. But we have no real experience with the software. Pulling all drives, rebooting the system, changing into the areca controller bios, reinserting the HDDs one-by-one. Some people are saying that the brought the system online by this. Some are saying that the effect is zero. Some say, that they blew the whole thing. Using undocumented areca commands like "rescue" or "LeVel2ReScUe". Contacting a computer forensics service. But whoa... primary estimates by phone exceeded 20.000€. That's why we would kindly ask for help. Maybe we are missing the obvious? And yes of course, we have backups. But some systems lost one week of data, thats why we'd like to get the system up and running again. Any help, suggestions and questions are more than welcome.

  Read the article

• Mac OS X Lion 10.7.2 update breaks SSL

  - by mcandre

  Summary After updating from 10.7.1 to 10.7.2, neither Safari nor Google Chrome can load GMail. Spinning Beachballs all around. The problem isn't GMail; Firefox loads GMail just fine. The problem isn't limited to Safari or Google Chrome; Other applications also have trouble with SSL: Gilgamesh and Safari. Any program that uses WebKit (Google Chrome, Safari) or a Cocoa library (Gilgamesh) to access the Internet has trouble loading secure sites. The various forums online suggest a handful of fixes, none of which work. Analysis Fix #1: Open Keychain Access.app and delete the Unknown certificate. The 10.7.2 update also prevents Keychain Access from loading. The Keychain program itself Spinning Beachballs. Fix #2: Delete ~/Library/Keychains/login.keychain and /Library/Keychains/System.keychain. This temporarily resolves the issue, and lets you load secure sites, but a minute or two after rebooting or hibernating somehow magically undoes the fix, so you have to delete these files over and over. Fix #3: Delete ~/Library/Application\ Support/Mob* and /Library/Application\ Support/Mob*. There is a rumor that the new MobileMe/iCloud service ubd is causing the issue. This fix does not resolve the issue. Fix #4: Open Keychain Access, open the Preferences, and disable OCSP and CRL. This fix does not resolve the issue. Fix #5: Use the 10.7.0 - 10.7.2 combo installer, rather than the 10.7.1 - 10.7.2 installer. When I run the combo installer, it stays forever at the "Validating Packages..." screen. The combo installer itself is bugged to He||. I force-quit the installer, ran "sudo killall installd" to force-quit the background installer process, and reran the combo installer. Same problem: it stalls at "Validing Packages..." Recap The only fix that works is deleting the keychains, but you have to do this every time you reboot or wake from hibernate. There is some evidence that ubd continually corrupts the keychain files, but the suggested ubd fix of deleting ~/Library/Application\ Support/Mob* and /Library/Application\ Support/Mob* does not resolve this issue. Evidently, something is corrupting the keychain over and over and over. Also posted on the Apple Support Communities.

  Read the article

• Losing internet connectivity on server after installing LogMeIn Hamachi (with server set as gateway node)

  - by Kim Jong-Un

  Our domain controller (SBS 2003) completely lost internet and network connectivity yesterday after I remotely installed LogMeIn Hamachi on it and set it to be a gateway node- in an attempt to create a VPN link between the server and a remote site. I had to go in to the office to resolve the problem as, unsurprisingly, my own remote access to the server was also lost. I was only able to restore network connectivity by deleting a virtual network adapter Hamachi created when making the server the gateway node (called "Hamachi bridge" I believe), then rebooting the server. This is a repeatable problem. Every time I try to get this to work, it just takes the server offline. Why would this bridge affect regular TCP/IP connectivity on the NIC in this way? I have tried a "hub-and-spoke" configuration between the server and our PC at a remote site (server set as hub, remote site as spoke). This caused no such problems with general internet connectivity, and file transfer worked well between the two computers. However, there was a DNS issue with the VPN between the two sites- resulting in Active Directory not being able to communicate between them (could not log on using domain user accounts at remote site if they were not already cached on that machine). I only tried a "gateway" network as LogMeIn support told me: If you can get the Active Directory to work it would only be through a "Gateway" network type with the server acting as the Gateway Node. You would configure the gateway settings on the server in the Hamachi client on that machine to push whatever IP's/DNS settings you prefer and at that point AD would be able (all things being equal) communicate to the client node when it attaches. We do not have any ActiveDirectory configuration info as that's outside the scope of our support. I hope this helps. It would be fantastic if I could get Active Directory to work over a Hamachi VPN connection, without worrying about the server going offline in this way. Does anyone have any ideas how I should proceed, or any theories as to what is going on when I try to use the "gateway" network type? I want to try to narrow down what is going on here.

  Read the article

• usb mouse connecting and disconnecting randomly and often

  - by Kalec

  Yes, I know this question has been asked here before but I can't add to the discussion over there and it did not help me, so here goes nothing. I've bought an acer aspire 5742G about 2 months ago or so and it's been running great, but sometimes I used to hear the windows error beep but I had no idea what was causing it since the "bug" was automatically fixed so fast I couldn't even see an error message (also it kinda always happened when I was busy also, either in a game or while doing my homework). Later on my mouse would simply not work for 3-5 seconds then work again, I thought nothing of it at the time. I also had a problem where it only worked in one usb and one only ... to move it I had to remove the battery, unplug the laptop and hold the power button for 2 minutes to reset the bios settings. Since today though it went nuts ... sometimes it disconnects / reconnects 12 times in 10 seconds and windows just keeps beeping till I unplug it, then it runs smooth for 5-6 minutes then it goes nuts again. Other times it seems like it skips (disconnects for a fraction of a second) other times just for 2-3 seconds. But this is incredibly frustrating. Sometimes the power just goes down (the laser turns off) and well that at least I would understand but this is a rare occurance. Now I know the usb ports work since I have a lot of other devices connected and I tried the mouse on a room m8's laptop so the mouse also works. My only conclusion is that it's an operating system / settings bug and / or problem (I have tried the mouse in all ports by the way). All drivers and bios are up to date (maybe except mouse but i can't seem to update that and the mouse has no name, just a serial number which helps with nothing. Still it worked till today and nothing should have changed any way). I have made sure windows can't shut it down to save power (in device management). Also I tried to delete the drivers and re-install them, rebooting and the power button trick but nothing ... most I have done is get rid of the 12 discconnects / reconnects every 10 seconds :) but that's all :( I would buy a new one but I'm afraid it might do the same thing :| ****EDIT****** Tried the mouse again at a friend but now it didn't even install it's software nor did the update work ... think I'll just buy a new one but I'd still like a suggestion at least so I'll leave this open

  Read the article

• External USB HD issues with a twist (works on Windows7 but not XP)

  - by Eruditass

  I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

  Read the article

• Hang while starting several daemons [solved]

  - by Adrian Lang

  I’m running a Debian Squeeze AMD64 server. Target runlevel after boot is runlevel 2, which includes rsyslogd, cron, sshd and some other stuff, but not dovecot, postfix, apache2, etc. The system fails to reach runlevel 2 with several symptoms: The system hangs at trying to start rsyslogd Booting into runlevel 1 works, then login from the console works Starting rsyslogd from runlevel 1 via /etc/init.d/rsyslog hangs Starting runlevel 2 with rsyslogd disabled works But then, logging in via console fails: I get the motd, and then nothing Starting sshd from runlevel 1 succeeds But then, I cannot login via ssh. Sometimes password ssh login gives me the motd and then nothing, sometimes not even this. Trying to offer a public key seems to annoy the sshd enough to not talk to me any further. When rebooting from runlevel 1, the server hangs at trying to stop apache2 (which is not running, so this really should be trivial). Trying to stop apache2 when logged in in runleve 1 does hang as well. And that’s just the stuff which fails all the time. RAM has been tested, dmesg shows no problems. I have no clue. Update: (shortened) output from rsyslogd -c4 -d called in runlevel 1 rsyslogd 4.6.4 startup, compatibility mode 4, module path '' caller requested object 'net', not found (iRet -3003) Requested to load module 'lmnet' loading module '/user/lib/rsyslog/lmnet.so' module of type 2 being loaded conf.c requested ref for 'lmnet', refcount 1 rsylog runtime initialized, version 4.6.4, current users 1 syslogd.c requested ref for 'lmnet', refcount now 2 I can kill rsyslogd with Strg+C, then. /var/log shows none of the configured log files, though. Update2: Thanks to @DerfK I still have no clue, but at least I narrowed down the problem. I’m now testing with /etc/init.d/apache2 stop (without an apache2 running, of course) which hangs as well and looks like an even more obvious failure. After some testing I found out that a file with one single line: /usr/sbin/apache2ctl configtest /dev/null 2&1 hangs, while the same line executed in an interactive shell works. I was not able to further reduce this line while, i. e. every single part, the stream redirections and the commando itself is necessary to reproduce the hang. @DerfK also pointed me to strace which gave a shallow hint about what kind of hang we have here: wait4(-1for the init scripts futex(0xsomepointer, FUTEX_WAIT_PRIVATE, 2, NULL for rsyslogd / apache2 binaries called by the init scripts The system was installed as a Debian Lenny by my hoster in autumn 2011, I upgraded it to Squeeze immediately and kept it up to date with Squeeze, which then used to be testing. There were no big changes, though. I guess I never tried to reboot the system before. Update3: I found the problem. My /etc/nsswitch.conf specified ldap as hosts lookup backup, which is not available at that time of the boot. Relying on dns solely fixes my boot problems.

  Read the article

• USB mouse connecting and disconnecting randomly

  - by Kalec

  I've bought an acer aspire 5742G about 2 months ago or so and it's been running great, but sometimes I used to hear the windows error beep but I had no idea what was causing it since the "bug" was automatically fixed so fast I couldn't even see an error message (also it kinda always happened when I was busy also, either in a game or while doing my homework). Later on my mouse would simply not work for 3-5 seconds then work again, I thought nothing of it at the time. I also had a problem where it only worked in one usb and one only. To move it I had to remove the battery, unplug the laptop and hold the power button for 2 minutes to reset the bios settings. Since today though it went nuts. Sometimes it disconnects / reconnects 12 times in 10 seconds and windows just keeps beeping till I unplug it, then it runs smooth for 5-6 minutes then it goes nuts again. Other times it seems like it skips (disconnects for a fraction of a second) other times just for 2-3 seconds. But this is incredibly frustrating. Sometimes the power just goes down (the laser turns off) and well that at least I would understand but this is a rare occurrence. Now I know the usb ports work since I have a lot of other devices connected and I tried the mouse on a room m8's laptop so the mouse also works. My only conclusion is that it's an operating system / settings bug and / or problem (I have tried the mouse in all ports by the way). All drivers and bios are up to date (maybe except mouse but I can't seem to update that and the mouse has no name, just a serial number which helps with nothing. Still it worked till today and nothing should have changed any way). I have made sure windows can't shut it down to save power (in device management). Also I tried to delete the drivers and re-install them, rebooting and the power button trick but nothing. Most I have done is get rid of the 12 disconnects / reconnects every 10 seconds :) but that's all :( I would buy a new one but I'm afraid it might do the same thing. ****EDIT****** Tried the mouse again at a friend but now it didn't even install it's software nor did the update work. Think I'll just buy a new one but I'd still like a suggestion at least so I'll leave this open #### EDIT 2 Now it works again, I can't explain this. Still thinking of getting a new one though

  Read the article

• How could I let Skydrive desktop sync to MicroSD in Windows 8 tablet?

  - by peSHIr

  I have a Samsung Slate 7 tablet with (now) Windows 8 on it. This machine has a 64 Gb SSD and I have a 64 Gb MicroSD card in it. I also have a Skydrive on my main Microsoft ID that contains about 45 Gb of content. With Windows and some development stuff installed, my Skydrive will not fit on the main drive of the tablet. (Besides, my idea was to keep data on the memory card anyway, to make it easier to repave the machine without data loss if need be.) My problem should now be clear: I want to install the Skydrive desktop app to sync my Skydrive to the MicroSD card. This is not possible, as Skydrive does not allow syncing files to removable drives. I have tried a number of things already, but none of them worked: Use the mklink command line tool to create a directory link/junction from a folder name on SSD to a folder on the MicroSD and then try to install Skydrive sync to the SSD link folder. Skydrive however still recognizes this as something it does not want to sync onto. The various different filter drivers mentioned on Agnipulse (including the Hitachi one) that should make windows see some or all of the removable drives in the system as fixed drives do not seem work on (64-bit) Windows 8: they either can't be installed, do nothing and/or cause Windows 8 to go into Automatic Repair mode when rebooting. The Lexar BootIt app seems to be meant to flip the relevant bit in the on-board drive controller of supported USB pen drives, but I tried it anyway. Of course it did nothing to how the MicroSD card was seen. I have now run out of ideas, it seems, and I was wondering if anyone here has a solution to let Windows 8 see the MicroSD memory card in my tablet as a fixed drive instead of removable drive, or some other way of getting the Skydrive desktop to sync my Skydrive data to that MicroSD card. And to be complete: this is not a duplicate question of this or this as those ask about getting USB drives multiple partitions to work on Windows XP. This question is specific about getting desktop Skydrive to sync to MicroSD card in Windows 8, which seems to be a question I have not seen on superuser so far.

  Read the article

• "Error 1067: The process terminated unexpectedly" when trying to install MySQL on Win7 x64.

  - by Gravitas

  Hi, I've run into a brick wall trying to install MySQL v5.5 on my machine. My PC is Windows 7 x64, Enterprise edition. MySQL installs fine, but when I run the "MySQL Instance Configuration Wizard", it pauses forever on the step "Start Service" (I can let it run for 30 minutes with no response). If I go into services, I see that the "MySQL" service hasn't started, and if I try to start it, it says "Windows could not start MySQL Service on Local Computer. Error 1067: The process terminated unexpectedly." I've tried the following: Turning off firewall. Uninstalling all antivirus software. Installing / reinstalling 32-bit version of MySQL. Installing / reinstalling 64-bit version of MySQL. Uninstalling, deleting the contents of "C:\program files\MySQL" and "C:\program files (x86)\MySQL", reinstalling. Checking to see that there is no rogue services named MySQL???? (from a previous install). Checking that port 3306 is not used by an alternate program. Changing the default port that MySQL uses. Checking for "my.ini" and "my.ini.cnf" in "C:\windows" (nothing there but that can cause a problem). Running both MySQL installer, and configuration wizard, in "Adminstrator mode". Turning off UAC. Installing with defaults, not changing anything. Rebooting my machine (about 6 reboots so far). Opening up port 3306 in the firewall (both TCP and UDP, inbound and outbound). Swearing at the klutz of a programmer who designed MySQL so you can't even install it (as if that would help!) My machine is working 100% in every other way. InfiniDB (a MySQL compatible database) installs 100%, as does Visual Studio 2010, Microsoft SQL Server, etc, etc. Your advice on how to work around this? p.s. Here is the screen it got stuck on for 15 minutes until I killed the process: Update 2010-12-20 Tried MySQL v5.1, it didn't work either. Its amazing - if you type "mysqld /?", or "mysqld -help", it doesn't give you any help. And, if you try to restart the service manually, it doesn't display any error messages. Could it be any more unhelpful? Update 2010-12-21 Installed MySQL 6.0 alpha, and it worked. However, I'd rather not use an alpha release, given that the "stable" release is anything but :( Update 2010-12-21 Found http://dev.mysql.com/doc/refman/5.1/en/windows-troubleshooting.html, dealing with troubleshooting under Windows. Discovered that you can generate an error log if the service doesn't start - see here: http://dev.mysql.com/doc/refman/5.1/en/error-log.html

  Read the article

• Hang while starting several daemons

  - by Adrian Lang

  I’m running a Debian Squeeze AMD64 server. Target runlevel after boot is runlevel 2, which includes rsyslogd, cron, sshd and some other stuff, but not dovecot, postfix, apache2, etc. The system fails to reach runlevel 2 with several symptoms: The system hangs at trying to start rsyslogd Booting into runlevel 1 works, then login from the console works Starting rsyslogd from runlevel 1 via /etc/init.d/rsyslog hangs Starting runlevel 2 with rsyslogd disabled works But then, logging in via console fails: I get the motd, and then nothing Starting sshd from runlevel 1 succeeds But then, I cannot login via ssh. Sometimes password ssh login gives me the motd and then nothing, sometimes not even this. Trying to offer a public key seems to annoy the sshd enough to not talk to me any further. When rebooting from runlevel 1, the server hangs at trying to stop apache2 (which is not running, so this really should be trivial). Trying to stop apache2 when logged in in runleve 1 does hang as well. And that’s just the stuff which fails all the time. RAM has been tested, dmesg shows no problems. I have no clue. Update: (shortened) output from rsyslogd -c4 -d called in runlevel 1 rsyslogd 4.6.4 startup, compatibility mode 4, module path '' caller requested object 'net', not found (iRet -3003) Requested to load module 'lmnet' loading module '/user/lib/rsyslog/lmnet.so' module of type 2 being loaded conf.c requested ref for 'lmnet', refcount 1 rsylog runtime initialized, version 4.6.4, current users 1 syslogd.c requested ref for 'lmnet', refcount now 2 I can kill rsyslogd with Strg+C, then. /var/log shows none of the configured log files, though. Update2: Thanks to @DerfK I still have no clue, but at least I narrowed down the problem. I’m now testing with /etc/init.d/apache2 stop (without an apache2 running, of course) which hangs as well and looks like an even more obvious failure. After some testing I found out that a file with one single line: /usr/sbin/apache2ctl configtest /dev/null 2&1 hangs, while the same line executed in an interactive shell works. I was not able to further reduce this line while, i. e. every single part, the stream redirections and the commando itself is necessary to reproduce the hang. @DerfK also pointed me to strace which gave a shallow hint about what kind of hang we have here: wait4(-1for the init scripts futex(0xsomepointer, FUTEX_WAIT_PRIVATE, 2, NULL for rsyslogd / apache2 binaries called by the init scripts The system was installed as a Debian Lenny by my hoster in autumn 2011, I upgraded it to Squeeze immediately and kept it up to date with Squeeze, which then used to be testing. There were no big changes, though. I guess I never tried to reboot the system before.

  Read the article

• Hot-swap drive got new name, can I change it on-the-fly?

  - by T.J. Crowder

  One of the HDDs in my server's RAID config failed, so I took it out of the array and had the data center hot-swap it. They've done that, but now the new drive is /dev/sdc rather than /dev/sda. I suspect — correct me if I'm wrong — that if I reboot the server, it will be /dev/sda again, so I'm hesitant to add it back to the array as /dev/sdc because I don't want to lay a trap for myself to fall into on the next reboot. I'd just as soon not reboot the server if I don't need to (if I do need to, well, too bad for me). Is there a way I can change the device name from /dev/sdc to /dev/sda without rebooting? This is on Ubuntu 10.04 LTS. It's an md array ("Linux Software RAID"), where currently one of the devices (there are a couple of them) looks like this ("degraded" because I've removed the old /dev/sda from it): # mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Sun Oct 11 21:07:54 2009 Raid Level : raid1 Array Size : 97536 (95.27 MiB 99.88 MB) Used Dev Size : 97536 (95.27 MiB 99.88 MB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 30 09:31:16 2011 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 UUID : 496be7a5:ab9177ed:7792c71e:7dc17aa4 Events : 0.112 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed Thanks, Update: Reading through the kernel md documentation, I suspect that if the name changes on reboot, it won't matter. (Good design, that.) Here's why: Boot time autodetection of RAID arrays When md is compiled into the kernel (not as module), partitions of type 0xfd are scanned and automatically assembled into RAID arrays. This autodetection may be suppressed with the kernel parameter "raid=noautodetect". As of kernel 2.6.9, only drives with a type 0 superblock can be autodetected and run at boot time. The kernel parameter "raid=partitionable" (or "raid=part") means that all auto-detected arrays are assembled as partitionable. I do have md compiled into the kernel, so I'm rebuilding the array now and will do the reboot to see what happens. Even if it works, the above doesn't answer the question I actually asked, so unless someone comes along and answers that question in the meantime (I'd be interested, even if it's not necessary for what I'm doing this very moment), I'll just delete the question to keep noise down.

  Read the article

• WIndows 7 cannot boot - bootrec reports FS not found or corrupt

  - by purecharger

  For 3 days now I've been unable to boot into my Windows 7 partition, and all my research has been to no avail. I'm hoping someone here has more ideas on how to fix this. When I boot up now, I get the black screen with BCD error that says theres no valid file system or it may be corrupt (pardon my lack of detail, no copy/paste is available then). When I boot with the Windows 7 disc and go into repair tools, no operating system is found, and attempting to automatically repair the problem fails with Unknown Operating System (Unknown Disk) or something similar. When I drop into the command prompt, I am able to see and navigate my C:\ drive without issue. I attempt to use bootrec: C:\> bootrec /ScanOS Finds C:\Windows as a system partition. C:\> bootrec /RebuildBCD Fails with volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted. So then I attempt to fix the bootsector: C:\> bootsect /nt60 C: /force Which completes successfully (sorry, no output..) Upon rebooting, I have the same problem. I've also tried all of the above after making my Windows partition active: C:\> diskpart DISKPART> select disk 1 DISKPART> select partition 1 DISKPART> active DISKPART> exit Then bootrec as above, both with and without a reboot after the DISKPART commands. Then I've also tried rebuilding the BCD store by hand: set systemdrive=C: set tempbcd=C:\boot\bcd.temp set tempfile=C:\boot\temp.txt bcdedit -createstore %tempbcd% bcdedit.exe -store %tempbcd% -create {bootmgr} -d "Windows Boot Manager" bcdedit -store %tempbcd% -create -d "Windows Vista" -application osloader>%tempfile% set /p winvistaguid= <%tempfile% set winvistaguid=%winvistaguid:~10,38% bcdedit -store %tempbcd% -set %winvistaguid% osdevice partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% device partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% path \Windows\system32\winload.exe bcdedit -store %tempbcd% -set %winvistaguid% systemroot \Windows bcdedit -import %tempbcd% However on the import, I get my familiar friendly message: volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted I'm at my wits end here, and I cannot understand why Windows refuses to see this as a valid install. When I list the disk/partition in DISKPART, it shows up as NTFS and "Healthy", and I can navigate the directory structure from DOS with no problems. I really, really do not want to reformat and reinstall. I know this problem can be solved!

  Read the article

• WIndows 7 cannot boot - bootrec reports FS not found or corrupt

  - by purecharger

  For 3 days now I've been unable to boot into my Windows 7 partition, and all my research has been to no avail. I'm hoping someone here has more ideas on how to fix this. When I boot up now, I get the black screen with BCD error that says theres no valid file system or it may be corrupt (pardon my lack of detail, no copy/paste is available then). When I boot with the Windows 7 disc and go into repair tools, no operating system is found, and attempting to automatically repair the problem fails with Unknown Operating System (Unknown Disk) or something similar. When I drop into the command prompt, I am able to see and navigate my C:\ drive without issue. I attempt to use bootrec: C:\> bootrec /ScanOS Finds C:\Windows as a system partition. C:\> bootrec /RebuildBCD Fails with volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted. So then I attempt to fix the bootsector: C:\> bootsect /nt60 C: /force Which completes successfully (sorry, no output..) Upon rebooting, I have the same problem. I've also tried all of the above after making my Windows partition active: C:\> diskpart DISKPART> select disk 1 DISKPART> select partition 1 DISKPART> active DISKPART> exit Then bootrec as above, both with and without a reboot after the DISKPART commands. Then I've also tried rebuilding the BCD store by hand: set systemdrive=C: set tempbcd=C:\boot\bcd.temp set tempfile=C:\boot\temp.txt bcdedit -createstore %tempbcd% bcdedit.exe -store %tempbcd% -create {bootmgr} -d "Windows Boot Manager" bcdedit -store %tempbcd% -create -d "Windows Vista" -application osloader>%tempfile% set /p winvistaguid= <%tempfile% set winvistaguid=%winvistaguid:~10,38% bcdedit -store %tempbcd% -set %winvistaguid% osdevice partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% device partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% path \Windows\system32\winload.exe bcdedit -store %tempbcd% -set %winvistaguid% systemroot \Windows bcdedit -import %tempbcd% However on the import, I get my familiar friendly message: volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted I'm at my wits end here, and I cannot understand why Windows refuses to see this as a valid install. When I list the disk/partition in DISKPART, it shows up as NTFS and "Healthy", and I can navigate the directory structure from DOS with no problems. I really, really do not want to reformat and reinstall. I know this problem can be solved!

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• Internet Explorer cannot display page from apache with single SSL virtual host

  - by P.scheit

  I have a question that has come up somehow in different questions but I still can't find the solution, yet. My problem is that I'm hosting a site on apache 2.4 on debian with SSL and Internet Explorer 7 on windows xp shows Internet Explorer cannot display the webpage I have only ONE virtual host that uses ssl, but DIFFERENT virtual hosts that use http. Here is my config for the site with SSL enabled (etc/sites-avaible/default-ssl is NOT linked) <Virtualhost xx.yyy.86.193:443> ServerName www.my-certified-domain.de ServerAlias my-certified-domain.de DocumentRoot "/var/local/www/my-certified-domain.de/current/www" Alias /files "/var/local/www/my-certified-domain.de/current/files" CustomLog /var/log/apache2/access.my-certified-domain.de.log combined <Directory "/var/local/www/my-certified-domain.de/current/www"> AllowOverride All </Directory> SSLEngine on SSLCertificateFile /etc/ssl/certs/www.my-certified-domain.de.crt SSLCertificateKeyFile /etc/ssl/private/www.my-certified-domain.de.key SSLCipherSuite HIGH:MEDIUM:!aNULL:+SHA1:+MD5:+HIGH:+MEDIUM SSLCertificateChainFile /etc/apache2/ssl.crt/www.my-certified-domain.de.ca BrowserMatch "MSIE [2-8]" nokeepalive downgrade-1.0 force-response-1.0 </VirtualHost> <VirtualHost *:80> ServerName www.my-certified-domain.de ServerAlias my-certified-domain.de CustomLog /var/log/apache2/access.my-certified-domain.de.log combined Redirect permanent / https://www.my-certified-domain.de/ </VirtualHost> my ports.conf looks like this: NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> the output from apache2ctl -S is like this: xx.yyy.86.193:443 www.my-certified-domain.de (/etc/apache2/sites-enabled/020-my-certified-domain.de:1) wildcard NameVirtualHosts and _default_ servers: *:80 is a NameVirtualHost default server phpmyadmin.my-certified-domain.de (/etc/apache2/conf.d/phpmyadmin.conf:3) port 80 namevhost phpmyadmin.my-certified-domain.de (/etc/apache2/conf.d/phpmyadmin.conf:3) port 80 namevhost staging.my-certified-domain.de (/etc/apache2/sites-enabled/010-staging.my-certified-domain.de:1) port 80 namevhost testing.my-certified-domain.de (/etc/apache2/sites-enabled/015-testing.my-certified-domain.de:1) port 80 namevhost www.my-certified-domain.de (/etc/apache2/sites-enabled/020-my-certified-domain.de:31) I included the solution for this question: Internet explorer cannot display the page, other browsers can, possibly htaccess / server error And I understand the answer from this question: How to setup Apache NameVirtualHost on SSL? In fakt: I only have one ssl certificate for the domain. And I only want to run ONE virtual host with ssl. So I just want to use the one ip for the ssl virtual host. But still (after rebooting / restarting / testing) internet explorer will still not show the page. When I intepret the apachectl -S as well, I already have only one SSL host and this should response to the initial SSH handshake, shouldn't it? What is wrong in this setup? Thank you so much Philipp

  Read the article

• How did what appears to be a virus get on my computer? (explanation of situation enclosed)

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• Unable to burn Windows ISO from Fedora

  - by user331947

  First of all, English is not my native tongue, so apologies for any mistakes. My computer recently started prompting that it can't launch Windows successfully. So I just choose start Windows normally. Then, I found that the startup freezes at the Windows screen (before the login prompt). I have tried rebooting several times and get the same results. So I just gave up. After few days, I tried to boot up my laptop again. This time it got to the desktop, but it's extremely slow and the icons on my Desktop don't show up. I decided to format the Windows partition and reinstall a new one. (It is usually faster that way since I kept my 400GB+ data on aother partition and programs and the rest in the same partition as Windows). The thing is I get the Windows disc at the moment (Traveling aboard). But I have a Windows 7 disc image on my hard disk. So, I downloaded Ubuntu 14.04 LTS, made a Live USB, and then try to burn the image from Ubuntu. But the program just freezes and I don't know why. I tried several times and it's still the same. So I tried using Fedora instead, just to see if it will work. The Disk Image Writer report something like this. Error unmounting /dev/dm-0: Command-line `umount "/dev/dm-0"' exited with non-zero exit status 32: umount: /: target is busy (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1).) (udisks-error-quark, 14) Also, I tried installing linux on the windows partition. The installation program freezes (both Ubuntu and Fedora). So, I thought that maybe something are wrong with my hard disk. I seek the solution on the internet and found that gparted can be used to format a partition. And it also froze at "Searching /dev/sda/ partition ...". I'm using Lenovo Y570. Spec below. http://www.notebookreview.com/notebookreview/lenovo-ideapad-y570-review-a-lenovo-bestseller/3/ Can anyone suggest a next step in diagnosing and fixing this problem? Thanks in advance.

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• PHP 5.2 to 5.3 not upgrading, no errors

  - by Webnet

  I'm following this guide: http://atik97.wordpress.com/2010/06/12/how-to-upgrade-to-php-5-3-in-ubuntu-9-10/ I've done all the steps, but it's still showing php 5.2.6 - any ideas? I have also tried -cgi instead of -cli, neither have any effect. update I've tried rebooting the server to see if that would have any effect and unfortunately it didn't update Output of dpkg -l *php*: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err: uppercase=bad) ||/ Name Version Description +++-=============================================-=============================================-========================================================================================================== un libapache2-mod-php4 <none> (no description available) ii libapache2-mod-php5 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (Apache 2 module) un libapache2-mod-php5filter <none> (no description available) ii php-pear 5.2.6.dfsg.1-3ubuntu4.6 PEAR - PHP Extension and Application Repository un php4-cli <none> (no description available) un php4-dev <none> (no description available) un php4-mysql <none> (no description available) un php4-pear <none> (no description available) ii php5 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.2.6.dfsg.1-3ubuntu4.6 command-line interpreter for the php5 scripting language ii php5-common 5.2.6.dfsg.1-3ubuntu4.6 Common files for packages built from the php5 source ii php5-curl 5.2.6.dfsg.1-3ubuntu4.6 CURL module for php5 un php5-dev <none> (no description available) ii php5-gd 5.2.6.dfsg.1-3ubuntu4.6 GD module for php5 ii php5-imap 5.2.6-0ubuntu5.1 IMAP module for php5 un php5-json <none> (no description available) ii php5-mcrypt 5.2.6-0ubuntu2 MCrypt module for php5 ii php5-mysql 5.2.6.dfsg.1-3ubuntu4.6 MySQL module for php5 un php5-mysqli <none> (no description available) ii php5-xsl 5.2.6.dfsg.1-3ubuntu4.6 XSL module for php5 un phpapi-20060613+lfs <none> (no description available) ii phpmyadmin 4:3.1.2-1ubuntu0.2 MySQL web administration tool update The following commands and their outputs: grep php53 /etc/apt/sources.list deb http://php53.dotdeb.org stable all deb-src http://php53.dotdeb.org stable all apt-cache search -f "libapache2-mod-php5" http://pastebin.com/XNXdsXYC update I've updated the question with more details on installed packages.

  Read the article

• Windows 8 disk errors

  - by wrongusername

  So yesterday, I forcibly restarted my Windows 8 PC. VMWare Workstation was having some trouble with the guest Linux Mint OS. It wasn't responding for some time, so I tried suspending it September 28th or perhaps even before. It wouldn't suspend -- I forgot what the window looked like, but all options in the power menu were disabled (i.e. "Shutdown," "Power Off," and options like that were all disabled). I eventually killed the VMWare application through Task Manager, though I was too lazy to hunt down the running virtual machine itself, and decided to kill it by just shutting down my PC entirely. The PC wouldn't shut down for quite some time after the monitor went blank, so I did a cold reset by holding the power button. I then powered it on again and Windows briefly gave me some message like "Search for KERNEL_STACK_INPAGE_ERROR." Windows then started diagnosing some problems and gave me the message, "Repairing disk errors. This might take over an hour to complete." That was yesterday night, and I went to sleep without waiting for it to finish. This morning, it said that the repair failed, and that the log was at C:\windows\system32\LogFiles\srt\srtTrail.txt (as I remember it -- I don't have the exact path I wrote down right now). It gave me some other options to troubleshoot, such as resetting Windows (files and settings still intact, but programs not installed through the app store will be erased). That didn't work (no error message given, I was just told it didn't work). I tried rebooting in safe mode, the same diagnosis process begins, except that this time it doesn't bother with the automatic repairs again. So I tried using the command prompt to try to see if my files are at least still there. I was on the X drive, and I couldn't cd to the C drive. I couldn't find my folder under Users (of course?), and couldn't find the srt folder under LogFiles either. I am not sure what to try next. I have backed up everything, but to the cloud, so if absolutely necessary I can start off with a fresh copy of Windows and restore all my data, though it would be a hassle. Any thoughts on what might be wrong or what I can try? My computer was purchased just this June, so the hard drive should still be pretty new.

  Read the article

• Repair corrupt hard disk on Mac without install CD

  - by Sarah

  The hard disk of my late 2009 MacBook Pro appears to have become corrupted. I am traveling and do not have my install CD (and won't for several weeks, nor will I be anywhere near an Apple store). The hard disk is not the original, which failed in June 2011. It's some Hitachi replacement installed by IT. History: I was typing an email this afternoon, my computer suddenly started making soft clicking sounds and then froze. I was not moving around. I rebooted, which took a while. I heard more clicking sounds and the computer froze at least once again. It's now kind of working, with mdworker sucking up one CPU. There are no awkward hard drive sounds when I run Chrome or play music. However, when I launched Stickies, I found no trace of my saved Stickies. I ran a live disk verification from within Disk Utility, and it reported Problem: As reported, I don't have access to an installation disc and am nowhere near an area where I can get one for at least two weeks. I have the option of asking someone to go to some trouble and expense to get one for me, but I'm not sure it's worth it: I've read that I can use fsck from single-user mode to repair the disk. Should I just try this? Is it risky? I'm concerned that the clicky sound portends imminent (mechanical) hard drive failure, so it's not worth doing a silly repair. This hard disk is backed up, but I definitely won't be able to access the backup while traveling. I'd like to maximize the probability that I can keep using my computer (and all its current files) while traveling. Update I bit the bullet and ran fsck -fy from single-user mode. It only needed one pass (modification) to reach the "okay" stage. However, rebooting took nearly 5 min and involved several rounds of scratchy sounds and a few bad clicks. I'm now back to kind of using my computer (the same files are missing as before). When I ran live disk verification from Disk Utility this time, however, it reported that the volume appears to be OK. Am I right to infer from the scratchy sounds, however, that my hard drive is still rapidly on its way out? Is there anything else I can do to increase its functionality over the next few weeks?

  Read the article

• Linux software RAID6: 3 drives offline - how to force online?

  - by Ole Tange

  This is similar to 3 drives fell out of Raid6 mdadm - rebuilding? except that it is not due to a failing cable. Instead the 3rd drive fell offline during rebuild of another drive. The drive failed with: kernel: end_request: I/O error, dev sdc, sector 293732432 kernel: md/raid:md0: read error not correctable (sector 293734224 on sdc). After rebooting both these sectors and the sectors around them are fine. This leads me to believe the error is intermittent and thus the device simply took too long to error correct the sector and remap it. I expect that no data was written to the RAID after it failed. Therefore I hope that if I can kick the last failing device online that the RAID is fine and that the xfs_filesystem is OK, maybe with a few missing recent files. Taking a backup of the disks in the RAID takes 24 hours, so I would prefer that the solution works the first time. I have therefore set up a test scenario: export PRE=3 parallel dd if=/dev/zero of=/tmp/raid${PRE}{} bs=1k count=1000k ::: 1 2 3 4 5 parallel mknod /dev/loop${PRE}{} b 7 ${PRE}{} \; losetup /dev/loop${PRE}{} /tmp/raid${PRE}{} ::: 1 2 3 4 5 mdadm --create /dev/md$PRE -c 4096 --level=6 --raid-devices=5 /dev/loop${PRE}[12345] cat /proc/mdstat mkfs.xfs -f /dev/md$PRE mkdir -p /mnt/disk2 umount -l /mnt/disk2 mount /dev/md$PRE /mnt/disk2 seq 1000 | parallel -j1 mkdir -p /mnt/disk2/{}\;cp /bin/* /mnt/disk2/{}\;sleep 0.5 & mdadm --fail /dev/md$PRE /dev/loop${PRE}3 /dev/loop${PRE}4 cat /proc/mdstat # Assume reboot so no process is using the dir kill %1; sync & kill %1; sync & # Force fail one too many mdadm --fail /dev/md$PRE /dev/loop${PRE}1 parallel --tag -k mdadm -E ::: /dev/loop${PRE}? | grep Upda # loop 2,5 are newest. loop1 almost newest => force add loop1 Next step is to add loop1 back - and this is where I am stuck. After that do a xfs-consistency check. When that works, check that the solution also works on real devices (such a 4 USB sticks).

  Read the article

• How TiVo is messing up customer support.

  - by James Fleming

  Ok,  So I've gotten a TiVo and overall, I'm happy, but there have been issues and I suspect I've a defective unit. - Now the nice folks after many service calls were happy to swap it out, and to ensure continuity of service, they sent me a new unit (after a $109 deposit).  That was yesterday. Today, when we go to watch a little TV, and wait for our replacement unit to arrive we find our TiVo service has been suspended. WTF? They have an exchange program, but your unit your waiting to exchange is as dead as a doornail until the replacement arrives. How hard is it to keep the old unit active for an extra week? Here is the exchange w/Tivo below... You are currently number 1 in the queue. We apologize for the delay. We will assign you to an agent as soon as one is available.The average amount of time a customer has to wait is 00:13.  Kaylene (Listening)  Kaylene: Thank you for contacting TiVo! My name is Kaylene. So that I may better assist you, are you an existing customer?  james Fleming: yes I am, but I'm now having second thoughts about being one    Kaylene: Thank you for verifying your information. How may I assist you today James?  james Fleming: I've been having issues w/a tivo box & I'm getting a replacement sent out to me (after paying an additional deposit) and now my current unit is no longer activated  Kaylene: I can help you today!  Kaylene: When we process an exchange we do transfer over the service to the replacement box so it is active and ready to go when you receive it.  james Fleming: which is to say you also make my current box worthless until such time I receive a new box?!?!?  Kaylene: I apologize that your original box was deactivated so we could activate your replacement box.  james Fleming: Why on Earth would I bother to pay in advance for a new box if you were going to kill my existing box.  Kaylene: What features are you needing to use on your current box?  james Fleming: I need to be able to access my netflix subscription (if I'm lucky enough to have it work without rebooting)  Kaylene: Can I have you verify the TiVo Service Number of your TiVo box please?  james Fleming: 7460011906979b4  Kaylene: We have your current box temporary service but not all features are available with temporary service as it is not paid for service.  Kaylene: If you like I can transfer your service back to your current box for now. Then once you receive the new box you will have to call in and have the service transferred back to the new box.  james Fleming: Not paid for? Let's see> one tivo box + 3 year service plan + monthly service + $109 deposit on a second box = what?  Kaylene: Would you like me to transfer your service back to your current box?  james Fleming: Yes - that would be helpful  Kaylene: All you will need to do is contact us again once you receive the new box so we can transfer it back.  Kaylene: I have put your service back on TiVo box 7460011906979b4.  james Fleming: What would also be helpful is your firm informing me to how you'd be cutting service in the interim.  james Fleming: Again - I opted to pay to have a second box delivered BEFORE returning the box I have - thus trying to have a continuity of service..  Kaylene: This is not something we normally do so it is important when you contact us to transfer the service back to the new box when you receive it that you reference this case number: 110622-006089.  Kaylene: I apologize about the inconvenience. You may need  force a few connections for the box to recognize the service again.  james Fleming: If it's not something you normally do than WHY would you have a $109 fee and a term for the service.  james Fleming: I am not mad at you, but your company is not impressing me and I'm blogging about this experience  Kaylene: Again I apologize about the inconvenience but you should be good to go now. Is there anything else I can help you with today?  james Fleming: so I need to go through the re-actviate process or is that somethign you do  Kaylene: When you receive the new TiVo box you need to contact us so we can transfer the service to the new box for you.  james Fleming: sure  Kaylene: Is there anything else I can help you with today James?  james Fleming: Nope - please email this transcript to me  Kaylene: I apologize but we do not have the ability to e-mail you a copy of this transcript. You can view it online at  http://www.tivo.com when you sign into your account or you can copy and paste it now to save it.  Kaylene: Thank you for contacting TiVo today. Your reference number for our conversation is 110622-006089. You can save this for your records, and if necessary, provide this to a later agent to pull up what we discussed. There will be a brief satisfaction survey emailed to you. We would appreciate any feedback on your TiVo Chat Support experience today.  Kaylene: Thank you for using TiVo Chat and have a great day James! Good-bye.  Kaylene has disconnected.

  Read the article

• Ubuntu 11 and 12 initially fast but later bogs down, CPU pegged

  - by uos??

  I started with Ubuntu 11 a few weeks ago. It's on a DELL M4300 with a OCZ SSD. Default setup, except that I've installed the proprietary NVIDIA graphics and BROADCOM wireless drivers. Dual boot with Windows. If I cold boot into Ubuntu, it is very fast, just like the Windows experience that I'm used to. But SOMETHING happens, and I haven't yet determined what, but the system gets incredibly slow and stays that way. At first I thought it had to do with Adobe Flash because it seemed to be triggered by sites with Flash. But then I removed Flash and the problem remains. I thought it was just an overheating problem, but I've now upgraded to 12.04 which supposedly fixes the overheating problems I've read about. Perhaps the heat situation was brought on by Flash in my early cases? So I installed Jupiter for CPU management, but the thermometer reports a familiar Windows-side temperature of 53 degrees Celsius. Switching Jupiter to lower performance doesn't help. When I check the System Monitor application, sorting by CPU usage, there are no obvious problem processes. However, in the graphs tab, both CPU cores are pegged at 100%! I notice that the slowness seems to be similar to the extremely bad performance I got prior to installing the NVIDIA drivers. I'm not sure if that helps. This is the strangest part to me - although the temperature seems OK, even after rebooting, the system remains slow - starting with GRUB2 which is very noticeably delayed, all the way through to either Ubuntu or Windows! That's right, even the Windows side suffers effects and takes several minutes to complete booting whereas normally (with my SSD) it's ready to use in 15 seconds. The only way to fix it is to shutdown and let the parts cool down. Or maybe it just needs to completely power off and boot rather than a soft reboot, temperature has nothing to do with it? - is that possible? But know that I have never had this problem in Windows, even if Windows gets very hot (135 F) a reboot would be enough time for it to recover. For this reason, I don't think it's a heat thing, but I can't imagine what else could be surviving the reboot. I'm entirely updated - there are no pending updates. I have the Post-Release updates of NVIDIA too, btw. If this sounds CLOSE to something you know about, but one of the details doesn't line up exactly, it might be a mistake in my perception. Are there tests you can suggest to rule something out? Thanks! processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5187.00 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5186.94 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: (Redundant figures removed. You can view them in the edits if they are still relevant) ps: %CPU PID USER COMMAND 9.4 2399 jason gnome-terminal 6.2 2408 jason bash 17.3 1117 root /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background none 13.7 1667 jason compiz 1.3 1960 jason /usr/lib/unity/unity-panel-service 1.3 1697 jason python /usr/bin/jupiter 0.9 1964 jason /usr/lib/indicator-appmenu/hud-service 0.6 1689 jason nautilus -n 0.4 1458 jason //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session I should highlight specifically that GRUB2 can also be very slow. I don't know the relationship of which scenarios GRUB2 is also slow, but WHEN it is slow, it is slow both before the menu appears and after the selection is made - although for the diagnosis of GRUB2 it is harder for me to tell what the normal speeds should be. With SSD, I would expect that GRUB2 could load instantly, and that the GRUB2 purple would disappear instantly after the selection. The only delay to be expected is the change in graphics modes (though I couldn't guess why that ever requires any noticeable time)

  Read the article

• Why is my external USB hard drive sometimes completely inaccessible?

  - by Eliah Kagan

  I have an external USB hard drive, consisting of an 1 TB SATA drive in a Rosewill RX35-AT-SU SLV Aluminum 3.5" Silver USB 2.0 External Enclosure, plugged into my SONY VAIO VGN-NS310F laptop. It is plugged directly into the computer (not through a hub). The drive inside the enclosure is a 7200 rpm Western Digital, but I don't remember the exact model. I can remove the drive from the enclosure (again), if people think it's necessary to know that detail. The drive is formatted ext4. I mount it dynamically with udisks on my Lubuntu 11.10 system, usually automatically via PCManFM. (I have had Lubuntu 12.04 on this machine, and experienced all this same behavior with that too.) Every once in a while--once or twice a day--it becomes inaccessible, and difficult to unmount. Attempting to unmount it with sudo umount ... gives an error message saying the drive is in use and suggesting fuser and lsof to find out what is using it. Killing processes found to be using the drive with fuser and lsof is sometimes sufficient to let me unmount it, but usually isn't. Once the drive is unmounted or the machine is rebooted, the drive will not mount. Plugging in the drive and turning it on registers nothing on the computer. dmesg is unchanged. The drive's access light usually blinks vigorously, as though the drive is being accessed constantly. Then eventually, after I keep the drive off for a while (half an hour), I am able to mount it again. While the drive doesn't work on this machine for a while, it will work immediately on another machine running the same version of Ubuntu. Sometimes bringing it back over from the other machine seems to "fix" it. Sometimes it doesn't. The drive doesn't always stop being accessible while mounted, before becoming unmountable. Sometimes it works fine, I turn off the computer, I turn the computer back on, and I cannot mount the drive. Currently this is the only drive with which I have this problem, but I've had problems that I think are the same as this, with different drives, on different Ubuntu machines. This laptop has another external USB drive plugged into it regularly, which doesn't have this problem. Unplugging that drive before plugging in the "problem" drive doesn't fix the problem. I've opened the drive up and made sure the connections were tight in the past, and that didn't seem to help (any more than waiting the same amount of time that it took to open and close the drive, before attempting to remount it). Does anyone have any ideas about what could be causing this, what troubleshooting steps I should perform, and/or how I could fix this problem altogether? Update: I tried replacing the USB data cable (from the enclosure to the laptop), as Merlin suggested. I should've tried that long ago, since it fits the symptoms perfectly (the drive works on another machine, which would make sense because the cable would be bent at a different angle, possibly completing a circuit of frayed wires). Unfortunately, though, this did not help--I have the same problem with the new cable. I'll try to provide additional detailed information about the drive inside the enclosure, next time I'm able to get the drive working. (At the moment I don't have another machine available to attach it.) Major Update (28 June 2012) The drive seems to have deteriorated considerably. I think this is so, because I've attached it to another machine and gotten lots of errors about invalid characters, when copying files from it. I am less interested in recovering data from the drive than I am in figuring out what is wrong with it. I specifically want to figure out if the problem is the drive or the enclosure. Now, when I plug the drive into the original machine where I was having the problems, it still doesn't appear (including with sudo fdisk -l), but it is recognized by the kernel and messages are added to dmesg. Most of the message consist of errors like this, repeated many times: [ 7.707593] sd 5:0:0:0: [sdc] Unhandled sense code [ 7.707599] sd 5:0:0:0: [sdc] Result: hostbyte=invalid driverbyte=DRIVER_SENSE [ 7.707606] sd 5:0:0:0: [sdc] Sense Key : Medium Error [current] [ 7.707614] sd 5:0:0:0: [sdc] Add. Sense: Unrecovered read error [ 7.707621] sd 5:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 7.707636] end_request: critical target error, dev sdc, sector 0 [ 7.707641] Buffer I/O error on device sdc, logical block 0 Here are all the lines from dmesg starting with when the drive is recognized. Please note that: I'm back to running Lubuntu 12.04 on this machine (and perhaps that's a factor in better error messages). Now that the drive has been plugged into another machine and back into this one, and also now that this machine is back to running 12.04, the drive's access light doesn't blink as I had described. Looking at the drive, it would appear as though it is working normally, with low or no access. This behavior (the errors) occurs when rebooting the machine with the drive plugged in, and also when manually plugging in the drive. A few of the messages are about /dev/sdb. That drive is working fine. The bad drive is /dev/sdc. I just didn't want to edit anything out from the middle.

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37  | Next Page >