Search Results

Search found 3593 results on 144 pages for 'wake on lan'.

Page 35/144 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• Static background noise while using new headset Ubuntu 13.04

  - by ThundLayr

  Today I bought a new gaming headset (Gx-Gaming Lychas), and when I tried to record some gameplay-comentary I noticed that there always is a static background noise, I just recorded an example so you guys can listen it (no downloaded needed): http://www47.zippyshare.com/v/65167832/file.html I'm using Kubuntu 13.04 and Kernel version is 3.8.0-19, my laptop is an Acer Travelmate 5760Z, I tried tons of configurations on Alsamixer and none of them made result, I really need to get this working so any kind of help will be very aprecciated. cat /proc/asound/cards: 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xc6400000 irq 44 cat /proc/asound/card0/codec#0 Codec: Conexant CX20588 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x14f1506c Subsystem Id: 0x10250574 Revision Id: 0x100003 No Modem Function Group found Default PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A State of AFG node 0x01: Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS Power: setting=D0, actual=D0 GPIO: io=4, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Headphone Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Headphone Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x4a 0x4a] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Speaker Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Speaker Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x80 0x80] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out Control: name="Beep Playback Volume", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Control: name="Beep Playback Switch", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0 Amp-Out vals: [0x00] Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Control: name="Capture Volume", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Control: name="Capture Switch", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x50 0x50] [0x80 0x80] [0x80 0x80] [0x80 0x80] Converter: stream=4, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Control: name="Mic Boost Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x04 0x04] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a 0x1b* 0x1d 0x1e Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a* 0x1b 0x1d 0x1e Node 0x19 [Pin Complex] wcaps 0x400581: Stereo Control: name="Headphone Jack", index=0, device=0 Pincap 0x0000001c: OUT HP Detect Pin Default 0x04214040: [Jack] HP Out at Ext Right Conn = 1/8, Color = Green DefAssociation = 0x4, Sequence = 0x0 Pin-ctls: 0xc0: OUT HP Unsolicited: tag=01, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1a [Pin Complex] wcaps 0x400481: Stereo Control: name="Internal Mic Phantom Jack", index=0, device=0 Pincap 0x00001324: IN Detect Vref caps: HIZ 50 80 Pin Default 0x90a70130: [Fixed] Mic at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0x3, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1b [Pin Complex] wcaps 0x400581: Stereo Control: name="Mic Jack", index=0, device=0 Pincap 0x00011334: IN OUT EAPD Detect Vref caps: HIZ 50 80 EAPD 0x0: Pin Default 0x04a19020: [Jack] Mic at Ext Right Conn = 1/8, Color = Pink DefAssociation = 0x2, Sequence = 0x0 Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=02, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1c [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00000014: OUT Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1d [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00010034: IN OUT EAPD Detect EAPD 0x0: Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1e [Pin Complex] wcaps 0x400481: Stereo Pincap 0x00000024: IN Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Control: name="Speaker Phantom Jack", index=0, device=0 Pincap 0x00000010: OUT Pin Default 0x92170110: [Fixed] Speaker at Int Front Conn = Analog, Color = Unknown DefAssociation = 0x1, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11* Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x12 Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x21 Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0 Amp-In vals: [0x00 0x00] Pincap 0x00000020: IN Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11 Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• wifi problems with lenovo g580 on kubuntu-13.04-desktop-amd64

  - by user203963

  i have a wifi connection problem in lenovo g580 on kubuntu-13.04-desktop-amd64. ethernet cable is working properly but wifi does'nt connect below are some hardware information sudo lshw -class network gives *-network description: Ethernet interface product: AR8162 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:89:84:3d:e9:10 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm pciexpress msi msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=alx driverversion=1.2.3 duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:90500000-9053ffff ioport:2000(size=128) *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:17 memory:90400000-90403fff *-network description: Wireless interface physical id: 3 logical name: wlan0 serial: 68:94:23:fa:2c:d9 capabilities: ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.8.0-19-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bgn lsubs gives Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0489:e032 Foxconn / Hon Hai Bus 002 Device 003: ID 04f2:b2e2 Chicony Electronics Co., Ltd lspci gives 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 10) 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Does anyone knows the solution? rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: yes Hard blocked: no 2: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 3: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• Setting up a mail server to send mail from IP

  - by Manishearth

  I have a fixed LAN IP, but no domain name. I'd like to be able to send emails within the LAN, and receive mails sent to my IP (user needs to send an email to [email protected]). I've tried the stuff in this post -- the "easy" one gives me an IMAP error in squirrelmail (IMAP is open and listening, but not working), and the "hard" one seems to be outdated. Is it possible to set up an email server (preferably on 12.04) without having a domain name?

  Read the article

• Can't enable wifi on vaio CW ubuntu 12.04

  - by rastemoh

  I was using my wifi with no problem, but an hour ago I switched it off from system settings and then tried to turn it on again, but no success. it's about 1 month I am using it and I had no problem with WIFI except this one. I rebooted and went to windows 7, but even that OS can't turn it on!! this is rfkill list all: 0: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: sony-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

• Wireless networks are not detected at start up in Ubuntu 12.04

  - by Kanhaiya Mishra

  I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

  Read the article

• Wireless is disabled by hardware switch on Dell Inspiron 1750

  - by lowerkey

  I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

  Read the article

• Windows 7 IIS 7 unable to receive incoming HTTP traffic

  - by gregarobinson

   I was trying to load a test html page from a LAN server that is running Windows 7. I could load the page from the server, but not from machines within the LAN. It took a while to figure out, but it turned ot to be the firewall in Windows 7. Here is what I had to do: Windows Firewall with Advanced Security ---> Inbound Rules ---> Enable World Wide receive incoming HTTP trafficWeb Services (HTTP Traffic-In)

  Read the article

• Routing Internet traffic over specific network interfaces [on hold]

  - by dipamchang

  I want to route my internet traffic over all my available connections (like LAN and Data card(3G)), based on conditions like, if a website is blocked over LAN, that traffic goes through Data Card (or other available internet connection). My ultimate motive is to integrate this feature in my web browser which I have already built using C# and .Net framework. I have found that one can add a route by using the following cmd command - route add DestinationIP mask subnet InterfaceGatewayIP but I am stuck as to how should it be implemented using C#?

  Read the article

• How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

  - by Annonomus Penguin

  I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

  Read the article

• networking tunnel adapter connections?

  - by Karthik Balaguru

  I understand that Tunnel Adapter LAN is for encapsulating IPv6 packets with an IPv4 header so that they can be sent across an IPv4 network. Few queries popped up in my mind based on this :- If i do 'ipconfig', Apart from ethernet adapter LAN details, I get a series of statments as below - Tunnel adapter Local Area Connection* 6 Tunnel adapter Local Area Connection* 7 Tunnel adapter Local Area Connection* 12 Tunnel adapter Local Area Connection* 13 Tunnel adapter Local Area Connection* 14 Tunnel adapter Local Area Connection* 15 Tunnel adapter Local Area Connection* 16 Except for the *16, all the other Tunnel Adapter Local Area Connections show Media Disconnected. Why is the numbering for the Tunnel adapter LAN not sequential? It is like 6, 7, 12, 13, 14, 15, 16. A strange numbering scheme! I tried to figure it out by thinking of some arithmetic series. But, it does not seem to fit in. There is a huge gap between 7 and 12. Any ideas? What is the need for so many Tunnel Adapter LAN connections? Can you tell me a scenario that requires all of those ? I did ipconfig /all to get more information. From the listing, I understand that: 16, 15, 14, 12 are Microsoft 6to4 Adapters 13, 6 are isatap Adapters 7 is Teredo Tunneling Pseudo-interface I understand that the above are for automatic tunneling so that the tunnel endpoints are determined automatically by the routing infrastructure. 6to4 is recommended by RFC3056 for automatic tunneling that uses protocol 41 for encapsulation. It is typically used when an end-user wants to connect to the IPv6 Internet using their existing IPv4 connection. Teredo is an automatic tunneling technique that uses UDP encapsulation across multiple NATs. That is, It is to grant IPv6 connectivity to nodes that are located behind IPv6-unaware NAT devices ISATAP treats the IPv4 network as a virtual IPv6 local link, with mappings from each IPv4 address to a link-local IPv6 address. That is to transmit IPv6 packets between dual-stack nodes on top of an IPv4 network. That is, to put in simple words, ISATAP is an intra-site mechanism, while the 6to4 and Teredo are for inter-site tunnelling mechanisms. It seems that Teredo should alone enabled by default in Vista, But my system does not show it to be enabled by default. Interestingly, it shows a 6to4 tunnel adapter (Tunnel adapter LAN connection 16) to be enabled by default? Any specific reasons for it? If i do ipconfig /all, why is only one Teredo present while four 6to4 are present ? I searched the internet for answers to the above queries, but I am unable to find clear answers.

  Read the article

• networking tunnel adapter connections?

  - by Karthik Balaguru

  I understand that Tunnel Adapter LAN is for encapsulating IPv6 packets with an IPv4 header so that they can be sent across an IPv4 network. Few queries popped up in my mind based on this :- If i do 'ipconfig', Apart from ethernet adapter LAN details, I get a series of statments as below - Tunnel adapter Local Area Connection* 6 Tunnel adapter Local Area Connection* 7 Tunnel adapter Local Area Connection* 12 Tunnel adapter Local Area Connection* 13 Tunnel adapter Local Area Connection* 14 Tunnel adapter Local Area Connection* 15 Tunnel adapter Local Area Connection* 16 Except for the *16, all the other Tunnel Adapter Local Area Connections show Media Disconnected. Why is the numbering for the Tunnel adapter LAN not sequential? It is like 6, 7, 12, 13, 14, 15, 16. A strange numbering scheme! I tried to figure it out by thinking of some arithmetic series. But, it does not seem to fit in. There is a huge gap between 7 and 12. Any ideas? What is the need for so many Tunnel Adapter LAN connections? Can you tell me a scenario that requires all of those ? I did ipconfig /all to get more information. From the listing, I understand that: 16, 15, 14, 12 are Microsoft 6to4 Adapters 13, 6 are isatap Adapters 7 is Teredo Tunneling Pseudo-interface I understand that the above are for automatic tunneling so that the tunnel endpoints are determined automatically by the routing infrastructure. 6to4 is recommended by RFC3056 for automatic tunneling that uses protocol 41 for encapsulation. It is typically used when an end-user wants to connect to the IPv6 Internet using their existing IPv4 connection. Teredo is an automatic tunneling technique that uses UDP encapsulation across multiple NATs. That is, It is to grant IPv6 connectivity to nodes that are located behind IPv6-unaware NAT devices ISATAP treats the IPv4 network as a virtual IPv6 local link, with mappings from each IPv4 address to a link-local IPv6 address. That is to transmit IPv6 packets between dual-stack nodes on top of an IPv4 network. That is, to put in simple words, ISATAP is an intra-site mechanism, while the 6to4 and Teredo are for inter-site tunnelling mechanisms. It seems that Teredo should alone enabled by default in Vista, But my system does not show it to be enabled by default. Interestingly, it shows a 6to4 tunnel adapter (Tunnel adapter LAN connection 16) to be enabled by default? Any specific reasons for it? If i do ipconfig /all, why is only one Teredo present while four 6to4 are present ? I searched the internet for answers to the above queries, but I am unable to find clear answers.

  Read the article

• Forwarding RDP via a Linux machine using iptables: Not working

  - by Nimmy Lebby

  I have a Linux machine and a Windows machine behind a router that implements NAT (the diagram might be overkill, but was fun to make): I am forwarding RDP port (3389) on the router to the Linux machine because I want to audit RDP connections. For the Linux machine to forward RDP traffic, I wrote these iptables rules: iptables -t nat -A PREROUTING -p tcp --dport 3389 -j DNAT --to-destination win-box iptables -A FORWARD -p tcp --dport 3389 -j ACCEPT The port is listening on the Windows machine: C:\Users\nimmy>netstat -a Active Connections Proto Local Address Foreign Address State (..snip..) TCP 0.0.0.0:3389 WIN-BOX:0 LISTENING (..snip..) And the port is forwarding on the Linux machine: # tcpdump port 3389 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 01:33:11.451663 IP shieldsup.grc.com.56387 > linux-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 01:33:11.451846 IP shieldsup.grc.com.56387 > win-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 However, I am not getting any successful RDP connections from the outside. The port is not even responding: C:\Users\outside-nimmy>telnet example.com 3389 Connecting To example.com...Could not open connection to the host, on port 3389: Connect failed Any ideas? Update Per @Zhiqiang Ma, I looked at nf_conntrack proc file during a connection attempt and this is what I see (192.168.3.1 = linux-box, 192.168.3.5 = win-box): # cat /proc/net/nf_conntrack | grep 3389 ipv4 2 tcp 6 118 SYN_SENT src=4.79.142.206 dst=192.168.3.1 sport=43142 dport=3389 packets=6 bytes=264 [UNREPLIED] src=192.168.3.5 dst=4.79.142.206 sport=3389 dport=43142 packets=0 bytes=0 mark=0 secmark=0 zone=0 use=2 2nd update Got tcpdump on the router and it seems that win-box is sending an RST packet: 21:20:24.767792 IP shieldsup.grc.com.45349 > linux-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.768038 IP shieldsup.grc.com.45349 > win-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.770674 IP win-box.myapt.lan.3389 > shieldsup.grc.com.45349: R 721745706:721745706(0) ack 755785049 win 0 Why would Windows be doing this?

  Read the article

• HP DL380 using HP NC522SFP NIC shows supported link modes: not reported

  - by MikeS

  When using ethtool on this NIC, the supported link modes show "not reported". Any idea why this is the case? Settings for eth0: Supported ports: [ FIBRE ] Supported link modes: Not reported Supported pause frame use: Symmetric Supports auto-negotiation: No Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 1 Transceiver: external Auto-negotiation: off Supports Wake-on: g Wake-on: g Current message level: 0x00002000 (8192) hw Link detected: yes

  Read the article

• Setup automated calling during an ETL failure

  - by Ryan M

  Just started working on a large data warehouse project that runs some large ETLs every night. In the event of an error I receive an email, but I was hoping to somehow create something that will automatically call me, so I don't have to wake up and check my email at 4 every morning to make sure the ETLs finished properly. I know I can setup an SMS pretty easily, but I don't think that will be enough to wake me up :) Anyone have any experience trying to do this before?

  Read the article

• Problems with MGCP proxy creation

  - by Popof

  Hi, I'm trying to bypass my ISP router with my FreeBSD server (I've an optical connection so I've a RJ45 used to connect the box to WAN) Internet and TV are working fine (Using igmpproxy to forward TV stream) but I've a problem with phone. ISP's box is connected to the server which gives it a LAN address. The problem is that when the box builds MGCP packets (and especially SDP ones) it uses its LAN address. So I've think of writing an UDP proxy to handle MGCP and SDP packets in order to replace LAN address with server WAN address and then forward packet to WAN. Before starting coding I've captured stream packets using my server as a bridge between WAN connection and the ISP's box. And, in order to see if my solution is viable, I've tried to send those packets to the box using nemesis. I tried to send a packet (found in capture) containing an endpoint audit: AUEP 1447 aaln/[email protected] MGCP 1.0 F: A In the wireshark capture the box replied: 200 1447 OK A: a:PCMU;PCMA;G726-16;G726-24;G726-32;G726-40;G.723.1-5.3;G.723.1-6.3;G729;TELEPHONE-EVENT, fmtp:"TELEPHONE-EVENT 0-15,144,149,159", p:10-30, b:4-40, e:on, t:00, s:on, v:L;M;G;D, m:sendonly;recvonly;sendrecv;inactive;confrnce;replcate;netwtest;netwloop, dq-gi But when I use nemesis, I got an ICMP error: Port unreachable (Type 3, Code 3). To build this packet, WAN source address of the capture is replaced with my server LAN address, using the mgcp-callagent port (2727) and the packet is sent to the LAN address of the box at mgcp-gateway port (2427). The command I use is nemesis udp -S 192.168.2.1 -D 192.168.2.2 -x 2727 -y 2427 -P packet_to_send. I also tried an UDP scan to the box on callagent and gateway port: PORT STATE SERVICE 2727/udp open|filtered unknown 2427/udp closed unknown I found those results a little bit strange because it should be the 2427 port opened, as it was in capture. Internet Protocol, Src: <ISP MGCP Server>, Dst: <My WAN Address> User Datagram Protocol, Src Port: mgcp-callagent (2727), Dst Port: mgcp-gateway (2427) Does someone has any idea about how having my box responding to my requests ? Thanks in advance and sorry for my english.

  Read the article

• I have a WinXP machine with 2 ethernet ports. One is connected to a LAN, another is connected to a WAN. How do I make this work?

  - by HappyEngineer

  I have a WinXP machine which has 2 ethernet ports. The information I've found indicates that the first nic in the advanced settings list is the one that receives all traffic. I'd like to configure them so that all traffic destined for a particular IP range goes to one nic and the rest goes to the other nic. Is that possible? If so, do I need additional software like zonealarm to shape the traffic?

  Read the article

• Cisco ASA and SixXS IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• Router slowing my connection?

  - by Roberto

  I have a Linksys WRT54G and I pay for a 12Mbps connection. I've been testing my connection using speedtest.net for many days and always get 8Mbps. I called the support and they told me to bypass the router and test. I did it and got 16Mbps (much more than I pay for), so I thought "this guy just changed my speed so can he blame my router", and he blamed it. But to my surprise, everytime I bypass the router I get 16Mbps and when I use the router I get 8Mbps. Is this guy trolling me somehow (configuring the VOIP-modem-stuff to different profiles depending o the MAC address connecting to it) or is my router a POS? How can I find out? I don't know what's the thing the router connects to, it's a kind of VOIP adapter; the link is this one, but unfortunately I don't think you'll understand because it's in Portuguese. I know they can remotely connect to it, that's the origin of my conspiracy theory :) I just tested wired to the router and got 10Mbps (and still 8Mbps on wifi and 16Mbps without router) O_o I'm 5cm away from my router, so no obstacles to interfere, right? ------ UPDATE ------- It's a WRT54G V8, I'm using firmware v8.00.7 (will install 8.00.8 tomorrow, but I saw that it's only a minor fix to UPnP denial of service security vulnerability). Results: IPerf LAN-LAN: 80Mbps IPerf LAN-WLAN: 19Mbps (therefore we can ignore wireless issues/settings) I wasn't able to make the (W)LAN-WAN NAT-enabled test with IPerf, I get a connection refused error. I'm not sure if did it right: ran in server mode, configured router to forward that port to my IP and tried to connect to my internet IP that got from this site. I don't think there is a way to disable NAT using this firmware. Question: Let's suppose it's an underpowered hardware issue. Is it right to assume that custom firmwares could resolve the issue because they are possibly better implemented and would make better use of the router resources? I couldn't find any references pointing to wired performance improvements with the use of custom firmware.

  Read the article

• Cisco ASA and static IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• special case ssh connection lag

  - by Hersheezy

  Setup We have a DMZ and LAN in our office that are connected to the outside with the following setup: +------+ | |------> LAN (normal office router) |Modem | | |------> DMZ (a single machine) +------+ Our internet account is with Comcast and we have 5 status IPs, one of which points to the single machine in the DMZ. Problem ssh connections initiated ANYWHERE EXCEPT the office LAN are really fast. However, from the LAN, there is about a 5 second delay. WTF?? Extra info The DMZ machine is debian 5. Executing a wget to the DMZ has no lag. When executing the following, everything up to HERE IS WHERE THE LAG IS INCURRED executes immediately. ssh -vvvv [email protected] ... debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/shopkins/.ssh/id_rsa (0x22440830) debug2: key: /home/shopkins/.ssh/identity ((nil)) debug2: key: /home/shopkins/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127` HERE IS WHERE THE LAG IS INCURRED debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/shopkins/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/shopkins/.ssh/identity debug3: no such identity: /home/shopkins/.ssh/identity debug1: Trying private key: /home/shopkins/.ssh/id_dsa debug3: no such identity: /home/shopkins/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password:

  Read the article

• Sophos UTM in Hyper-V

  - by TheD

  So, I had a previous thread about this Virtualizing Firewalls/UTM. Essentially, I have configured what I think would work, but networking isn't my strong point! Two Virtual Adapters - with IP addresses 192.168.0.2 (External) and 192.168.0.3 (Internal) respectively. The External Adapater looks at 192.168.0.1 (my Zyxel) for it's default gateway. The Internal Adapter, 192.168.0.3, which is what the Sophos UTM listens on, has it's default gateway set to 192.168.0.2, the IP of the External Lan interface. So, PC (192.168.0.11, DHCP) --> (LAN) --> Switch --> 192.168.0.3 (Internal LAN Interface IP) --> Sophos UTM --> 192.168.0.2 (External LAN Interface IP) --> 192.168.0.1 --> Internet Would this be the correct setup, or am I completely out of the game here? Cheers!

  Read the article

• Allow access from outside network with dmz and iptables

  - by Ivan

  I'm having a problem with my home network. So my setup is like this: In my Router (using Ubuntu desktop v11.04), I installed squid proxy as my transparent proxy. So I would like to use dyndns to my home network so I could be access my server from the internet, and also I installed CCTV camera and I would like to enable watching it from internet. The problem is I cannot access it from outside the net. I already set DMZ in my modem to my router ip. My first guess is because i'm using iptables to redirect all inside network to use squid. And not allow from outside traffic to my inside network. Here is my iptables script: #!/bin/sh # squid server IP SQUID_SERVER="192.168.5.1" # Interface connected to Internet INTERNET="eth0" # Interface connected to LAN LAN_IN="eth1" # Squid port SQUID_PORT="3128" # Clean old firewall iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X # Load IPTABLES modules for NAT and IP conntrack support modprobe ip_conntrack modprobe ip_conntrack_ftp # For win xp ftp client #modprobe ip_nat_ftp echo 1 > /proc/sys/net/ipv4/ip_forward # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT ACCEPT # Unlimited access to loop back iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # Allow UDP, DNS and Passive FTP iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT # set this system as a router for Rest of LAN iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT # unlimited access to LAN iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT # DNAT port 80 request comming from LAN systems to squid 3128 ($SQUID_PORT) aka transparent proxy iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT # if it is same system iptables -t nat -A PREROUTING -i $INTERNET -p tcp --dport 80 -j REDIRECT --to-port $SQUID_PORT # DROP everything and Log it iptables -A INPUT -j LOG iptables -A INPUT -j DROP If you know where did I miss, please advice me. Thanks for all your help and I really appreciate it.

  Read the article

• Adding a Second Wireless Router to an Existing Wired Network

  - by KVCrawford

  I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

  Read the article

• Sonicwall TZ210 - Set up public wifi on separate subnet & interface

  - by thomasjbarrett

  I want to set up a public wifi by connecting another router to the X6 interface, and put it on a separate subnet (192.168.10.0/24) & in the DMZ Zone to keep it away from the regular LAN. I believe I have the network settings correct: the router has acquired the IP and DNS information from the TZ210, and the TZ210 shows it as an active DHCP lease. X6 is in the DMZ. I now have a routing/NAT/firewall problem, since I can't get any traffic to travel from the subnet to the internet. I can't get to any external websites and can't ping the TZ210 from the subnet. X0 is the regular LAN, and X1 is the WAN. Looking for any tips or tutorials on this. Here's my current relevant rules: Routing Source: X6 Subnet Destination: Any Service: Any Gateway: Default Gateway Interface: X6 Source: Any Destination: X6 Subnet Service: Any Gateway: 0.0.0.0 Interface: X6 NAT Policies Source Original: Any Translated: WAN IP Destination Original: Any Translated: Original Inbound: X6 Outbound: X1 Source Original: Any Translated: U0 IP Destination Original: Any Translated: Original Inbound: X6 Outbound: U0 Firewall DMZ LAN : Deny All DMZ WAN : Allow All LAN DMZ : Allow All WAN DMZ : Allow All

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >