Search Results

Search found 26524 results on 1061 pages for 'laptop display'.

Page 36/1061 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

  • RDP for High DPI Monitors?

    - by Joey
    A client is having some problems with their laptop. They use RDP to remote into their work PC, but the laptop they are using is a small 13" Sony Vaio laptop, but with 1920x1080 resolution. Everything is pretty small on the laptop anyway, but the problem is much worse after connecting with RDP, where everything is almost unreadable. I have done the obvious with changing the resolution on the server, the RDP size, forced scaling on the terminal server etc, but nothing has worked. Something else which I would normally do is change the laptop resolution to something a little lower, but the laptop only has 2 resolution settings, the big one, and a 1024x768 (wrong ratio). Any ideas?

    Read the article

  • Laptop charger disconnects and reconnects, charger or battery broken?

    - by Rob
    I've got an Acer Aspire One netbook (AOA-150) and there's obviously something wrong with it. The charging port gets VERY HOT and the charger seems to disconnect and reconnect quickly sometimes. This only happens when the netbook is running, and it doesn't seem to care what it's doing other than being on. The battery has an extremely short life (< 30minutes, sometimes) and I almost exclusively run it on the power cable (which needs the battery plugged in. Having it just plugged into the wall won't start up). Does this sound like a problem with the power cable or the battery? The plug for the cable and the port get so hot that if I held them for longer than a few seconds, I'm sure I'd get burnt. EDIT Just got "Popular Question" on this and it WAS the power jack. The ground on it came loose from the board. A bit of solder on it and everything is working great again.

    Read the article

  • In general, do 3rd-party laptop AC adapters / chargers work reliably?

    - by MGOwen
    The AC adapters for my 2 dell laptops wore out very quickly. One supplies power but won't charge the battery (it's about 3 years old, the other is a bit newer). Both have worn through to the shielding around the notebook connector and look like they'll be unusable soon. Checking user reviews of the replacement adapter on Dell's own website, it appears they usually fail this fast. Apparently Dell does this deliberately to make money (their adapters sell for about 10-15 times what they cost to make). Same with replacement batteries. I can see there are plenty of much cheaper ($50 less) compatible AC adapters on eBay. Does anyone have experience with these? Naturally I'm nervous a crappy knock-off could fry my notebook, but has this ever actually happened to anyone recently? Has anyone had a good experience? Can anyone recommend a good online seller (who doesn't charge nonsensical shipping costs to Australia, preferably?)

    Read the article

  • Laptop connects to other network but not to my home wireless

    - by Nilesh
    My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

    Read the article

  • Laptop connects to other network but not to my home wireless

    - by Nilesh
    My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

    Read the article

  • Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

    - by leladax
    If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?]

    Read the article

  • Is there an easy way to disable this laptop's touchpad?

    - by sestocker
    Specifically, I'm on a Dell Inspiron 1525. I'd like to disable the touchpad so that I can re-enable if my mouse were to run out of batteries (so physically breaking the connection to the motherboard or uninstalling the driver will not be the best options). In the Control Panel, when I go to "Mouse" and find the touch pad, there is no disable option. Any ideas? Edit: I am on Windows 7. There is a driver on the Dell site that might allow an option to disable it, but I cannot install it on Windows 7.

    Read the article

  • Toshiba Satellite Laptop Realtek Network Driver Error code (10)?

    - by Silent
    hello all i have a Toshiba 64 bit windows vista, i tried looking for the drivers from the main website but no luck all the ones i got did not work or did not do anything. would someone know where i can find it or maybe fix this issue it will not find any network wireless or even if i hook up the Ethernet cable. i don't know why Toshiba makes it hard they should have a complete bundle. Model: A305-S687

    Read the article

  • Getting Xbox Live via a wired network with my laptop that has internet access wirelessly

    - by Alex Franco
    I'm running the latest version (as of yesterday anyways) of Ubuntu Desktop 64bit, but installed on my laptop if it makes a difference. I had Windows 7 preinstalled when i bought it and it worked fine with the wireless from my house and bridging the connection with a LAN to my xbox for Live. Now with Ubuntu I tried the same setup, but I'm unfamiliar with Ubuntu so I didn't get far. Best I got so far is wireless internet on my laptop and a wired connection to the xbox that continually connects and disconnects. Heres my network settings. if theres fields not included its because theyre empty on mine or theyre my MAC address or network password Wireless Network 1 settings: Connect Automatically: Checked. Available to all Users: Checked Wireless: SSID: Franco's Mode: Infrastructure MTU: Automatic IPv4 Settings: Method: Automatic (DHCP) IPv6 Settings: Method: Automatic Wired Network 1: Connect Automatically: Checked Available to all Users: Checked Wired: MTU: Automatic IPv4 Settings: Method: Automatic (DHCP) IPv6 Settings: Method: Automatic Any help would be greatly appreciated. EDIT: 6:26pm It seems to be staying connected now. Doing the Network test on my xbox it pickups the network, but cannot detect any PC. Restarting the Xbox, however, leaves my computer unable to connect bringing up the Wire Network disconnected 'blip' every minute or so again. Before I had restarted the Xbox it said "Connected 100 MB/s". Now it only says "connecting". I did have my computer and xbox on in this Wired Network Disconnected blip cycle for a long period of time so it may have finally connected, just without the ability to detect my laptop. I left for 2 hours or so in the middle of typing up the original question. I finished posting this when i got back and then tried to mess with it a bit again, in case youre wondering why i didnt include this before... I've said too much. Forgive my long-winded fingers :p

    Read the article

  • Ubuntu 12.04 LTS , Dell d410 output to External Monitor/TV with docking

    - by Gck
    I am not able to see the video output on My external monitor/TV after installing 12.04 LTS. I had the same issue with 11 versions also. This issue does not happen on 10.04 LTS version. This is my setup. Dell latitude D410 with Intel Mobile 915 GM/910GML express controller using the Dell docking station Connecting to my 42inch TV with DVI (from Docking) to HDMI cable (on TV) If i close the lid, some times i am able to see the video output on TV, but the resolution is making the fonts so small, i cannot even see it and when i click displays option to change the resolution, the output goes off completely and it is shown now on the laptop screen. one time, i got the output on both the screens, but i am not able to replicate that scenario even after trying the Fn+F8 key option on my laptop. earlier some time back when i ran version 11.x ubuntu, i was able to get the output on both the screens (basically mirrored output) with large font resolution on my TV using the monitor Test tool as mentioned here :http://www.bigfatostrich.com/2011/05/solved-ubuntu-11-04-broken-external-display/ The problem with this approach is that i have to do it every time i restart the machine and more over the video output is present on both the screens (mirrored), which is of no use. As i stated before, this does not happen with 10.04 LTS. With 10.04 LTS my laptop screen is off automatically and the output is seen on TV/external display. Can anyone share any options that i can try? How can we achieve the behavior of 10.04 LTS with respect to the External display on 12.04 LTS . Thankyou very much for your help in advance.

    Read the article

  • Change X settings to boot into laptop with non working screen using an external monitor

    - by dassouki
    My laptop committed suicide. Is there a way I can boot into my ubuntu using an external screen? Ubuntu 10.10 video: Nvidia 9500 gm i think I can get dual screen upto and until the ubuntu login screen at which point it goes back into laptop display only. Then I can just type and enter my password. The system (i assume boots into ubuntu) but I got no way of going onto the x or nvidia settings to change my display to external monitor EDIT well I booted into terminal using control shift F1 i think, and now I'm trying to reporgram x.org, but strangely it seems bland with not a lot of settings in it EDIT 2 xrandr returns "Can't open display" EDit 3 after some messing around with xrandr and xinit ... my x.org only displays one monitor instead of two in its settings although both, i.e. the laptop and external screens are both connected. EDIT 4 it seems that x.org now has a "screen" and "monitor" section, I can't seem to be able to boot linux into monitor. I get a "Monitor is not a valid keyword" in this subsection

    Read the article

  • Are Windows partitions gone?

    - by Gigili
    I had Windows 7 on my laptop (factory setting), because of some performance issues, I decided to use recovery options to restore it to its factory condition but I don't know what has happened or what I have done that the whole operating system was gone after playing around with recovery options from the boot menu. I couldn't find Windows, so I installed Ubuntu 11.04 on my laptop. Last time I had Ubuntu on it, it was not really compatible with laptop's configuration and I had a bit of problems trying to do normal tasks I used to do on Windows. Now I want to make sure that Windows and its drivers are gone so that I can try to install a newer version of Ubuntu or Windows. I tried the command sudo fdisk -l And the result shown was: myaccount@myaccount-VPCS116FG:~$ sudo fdisk -l [sudo] password for myaccount: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00025b5f Device Boot Start End Blocks Id System /dev/sda1 * 1 38409 308515840 83 Linux /dev/sda2 38409 38914 4052993 5 Extended /dev/sda5 38409 38914 4052992 82 Linux swap / Solaris Disk /dev/dm-0: 4150 MB, 4150263808 bytes 255 heads, 63 sectors/track, 504 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xa668cfe8 Disk /dev/dm-0 doesn't contain a valid partition table Is it gone? If not, what command should I try to have access to Windows partitions? Thank you.

    Read the article

  • Does lesser wide screen fit better than a large one?

    - by artaxerxe
    About 3 weeks ago I changed my job. At the former workplace, I had 2 monitors for doing programming (GUI and core programming). Here, at the place where I am, the administrators gave me a laptop (15.6 inch) and wanted to provide me a wider screen additional to the laptop's one. I said that for now I want to test as it is, with the laptop's screen. I also want to mention, that in the current job I'm not targeted for GUI development. My feeling until now (but it can be just a feeling) is that working on this single not so wide screen, I'm not so weary after a full day work as I was with 2 wide monitors. Does anyone have any recommendations on this problem? Does lesser screens (in my case exclusively 15.6 inch vs 20 inch screens) affect your eyes? If anyone have any knowledge about, please feel free to say what's your opinion. P.S. I think that's a good site for this kind of question. Otherwise, please guide me on what site from StackExchange should I put it. Thanks.

    Read the article

  • Automatic switching between monitor configurations

    - by Michael Aquilina
    I have a laptop and an external monitor and i was wondering if there was a simple approach to switching between multiple monitor configurations based on the detected available displays. For example: When i am at home and i plug in my external monitor i would like this to automatically become enabled and the laptop screen to become disabled. As soon as i pull out the display cable for the external monitor, i would like the laptop screen to automatically become enabled. I was expecting this to just "work" just like it does in windows - but it seems to be much harder than that. I am aware of the xrandr command to turn displays on and off but i cannot seem to find a way to get this to work the way i describe above. I had also found this post about switching between multiple monitor configurations and the results seem a bit inconclusive. However i was hoping that with xrandr there would be a simpler solution. For me, the fact that when i pull out my external monitor the screen just goes black and i get an error message is a big issue holding me back from making the complete switch to linux as i move around alot as a student. My OS of choice is currently Kubuntu 12.04 but i am willing to change to something else if it provides a better way of setting up the described setup.

    Read the article

  • My nVidia GeForce 8600M GT card stopped working: "extension GLX missing on display 0:0"

    - by Wolter Hellmund
    So I turned on my computer and log into my gnome-shell session to find that the shell is gone, and there is instead a very thick panel with a vertically repeated pattern of the gradient the Unity panel displays. I ran some tests and found out that my graphic acceleration was failing. I have attached some outputs of some commands to help helpers help me: Some command outputs Video card: nVidia GeForce 8600M GT (note that it is not an Optimus card). Output of lspci | grep VGA: 01:00.0 VGA compatible controller: NVIDIA Corporation G84 [GeForce 8600M GT] (rev a1) Output of glxinfo: Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Contents of /var/log/Xorg.0.log: NVIDIA: Failed to load the NVIDIA kernel module. Please check your NVIDIA: system's kernel log for additional error messages. UnloadModule: "nvidia" Unloading nvidia Failed to load module "nvidia" (module-specific error, 0) If I use the Aditional Drivers system application, I see none of the drivers active, and when I try to activate any, I get an error telling me to check the jockey.log file. The contents of /var/log/jockey.log are: 2012-09-20 23:11:32,690 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:32,690 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:11:34,606 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:11:34,657 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:34,657 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:11:36,647 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:36,648 DEBUG: KMH enabled: False 2012-09-20 23:11:38,642 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:38,642 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:11:40,546 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,546 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:11:40,620 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,620 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:11:40,629 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:11:40,698 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,698 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:11:40,759 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,760 DEBUG: KMH enabled: False 2012-09-20 23:11:40,826 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,826 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:11:45,415 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:45,415 DEBUG: KMH enabled: False 2012-09-20 23:11:47,367 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:47,367 DEBUG: KMH enabled: False 2012-09-20 23:11:55,961 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-09-20 23:11:55,962 ERROR: XorgDriverHandler.enable(): package or module not installed, aborting 2012-09-20 23:12:27,780 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:27,781 DEBUG: KMH enabled: False 2012-09-20 23:12:27,840 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:27,840 DEBUG: KMH enabled: False 2012-09-20 23:12:43,196 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,197 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:12:43,208 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:12:43,269 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,269 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:12:43,333 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,333 DEBUG: KMH enabled: False 2012-09-20 23:12:43,393 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,394 DEBUG: KMH enabled: False 2012-09-20 23:12:43,465 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,465 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:12:43,531 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,531 DEBUG: KMH enabled: False 2012-09-20 23:12:43,587 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,587 DEBUG: KMH enabled: False 2012-09-20 23:12:43,663 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,663 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:12:43,672 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:12:43,738 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,739 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:12:43,803 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,803 DEBUG: KMH enabled: False 2012-09-20 23:12:43,863 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,863 DEBUG: KMH enabled: False 2012-09-20 23:12:43,930 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,930 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:24:16,305 DEBUG: Shutting down Things I have tried Checked the video card on a Windows session. Reran nvidia-xconfig. Purged all nvidia software from my computer, and reinstall it. Run nvidia-xconfig. Tried a different kernel.

    Read the article

  • Can no longer duplicate display to external monitor on Windows 7

    - by rbeier
    We have a large TV at work - I connect my laptop to it to share my screen during meetings. Until today, my laptop display has been duplicating to the TV automatically when I connect the TV cable to the laptop. The display resolution would decrease automatically to be compatible with the TV. Today, however, it's stopped working. When I connect the cable to the TV, the display extends rather than duplicating. Using the Win+P key combination (or Fn+F7 on my Lenovo laptop), I can choose to duplicate the display - but when I do this, it ends up only displaying on the laptop. I can get it to display on the TV by hitting Win+P and choosing "projector only", but then I can't see what I'm doing on the laptop screen. I have a Lenovo W520 laptop running Windows 7, connected to the TV using a DisplayPort-to-HDMI converter cable. The TV's native resolution is 1280x720; the laptop's native resolution is 1600x900. I've tried booting with the TV cable already connected; I've tried manually lowering the display resolution on the laptop to 1280x720 before duplicating the display. Neither works. Does anyone have any other suggestions?

    Read the article

  • Dell Studio 1737 Overheating

    - by Sean
    I am using a Dell Studio 1737 laptop. I have been running Linux and have ran Windows recently for a very long time. I upgraded to the 10.10 distribution and since that distro, it seems that for some reason all Linuxes want to push my laptop to extremes. I have recently upgraded to Ubuntu 12.04 since I heart that it contains kernel fixes for overheating issues. 12.04 will actually eventually cool the system, but that is after the fans run to the point it sounds like a jet aircraft taking off and the laptop makes my hands sweat. In trying to combat the heat problems I have done the following: I installed the propriatery driver for my ATI Mobility HD 3600. I have tried both the one in the Additional Drivers and also tried ATI's latest greatest version. If I don't install this my laptop will overheat and shut off in minutes. Both seem to perform similarly, but the heat problem remains. I have tried limiting the CPU by installing the CPUFreq Indicator. This does help keep the machine from shutting off, but the heat is still uncomfortable to be around the machine. I usually run in power saver mode or run the cpu at 1.6 GHZ just to error on safety. I ran sensors-detect and here are the results: sean@sean-Studio-1737:~$ sudo sensors-detect # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: Dell Inc. Studio 1737 (laptop) # Board: Dell Inc. 0F237N This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Module cpuid loaded successfully. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... Yes Found `ITE IT8512E/F/G Super IO' (but not activated) Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel ICH9 Module i2c-i801 loaded successfully. Module i2c-dev loaded successfully. Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)y Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service module-init-tools start' to load them. Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK sean@sean-Studio-1737:~$ sudo service module-init-tools start module-init-tools stop/waiting I also tried installing i8k but that didn't work since it didn't seem to be able to communicate with the hardware (probably for different kind of device). Also I ran acpi -V and here are the results: Battery 0: Full, 100% Battery 0: design capacity 613 mAh, last full capacity 260 mAh = 42% Adapter 0: on-line Thermal 0: ok, 49.0 degrees C Thermal 0: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 1: ok, 48.0 degrees C Thermal 1: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 2: ok, 51.0 degrees C Thermal 2: trip point 0 switches to mode critical at temperature 100.0 degrees C Cooling 0: LCD 0 of 15 Cooling 1: Processor 0 of 10 Cooling 2: Processor 0 of 10 I have hit a wall and don't know what to do now. Any advice is appreciated.

    Read the article

  • Bridging my laptop's wireless and wired adaptors

    - by stacey.richards
    I would like to be able to connect a desktop computer that does not have a wireless adapter to my wireless network. I could just run a network cable from my ADSL/wireless router to the desktop computer but sometimes this is not practical. What I would really like to do is bridge my laptop's wireless and wired adapters in such a way that I can run a network cable from my laptop to a switch and another network cable from the switch to a desktop computer so that the desktop computer can access the Internet through my ADSL/wireless router via my latop: +--------------------+ |ADSL/wireless router| +--------------------+ | +-------------------------+ |laptop's wireless adaptor| | | |laptop's wired adaptor | +-------------------------+ | +------+ |switch| +------+ | +-----------------------+ |desktop's wired adapter| +-----------------------+ A bit of Googling suggests that I can do this by bridging my laptop's wireless and wired adapters. In Windows XP's Network Connections I select both the Local Area Connection and the Wireless Network Connection, right click and select Bridge Connections. From what I gather, this (layer 2?) bridge will examine the MAC address of traffic coming from the wireless network and pass it through to the wired network if it suspects that a network adapter with that MAC address may be on the wired side, and vice-versa. If this is the case, I would assume that when the desktop computer attempts to get an IP address from a DHCP server (which is running on the ADSL/wireless router), it would send a DHCP broadcast packet which would pass through the laptop's bridge to the router and the reply would return through the laptop's bridge back to the desktop. This doesn't happen. With some more Googling I find some instruction how this can be done with Linux. I reboot to Ubuntu 9.10 and type the following: sudo apt-get install bridge-utils sudo brctl addbr br0 sudo brctl addif br0 wlan0 sudo brctl addif br0 eth0 sudo ipconfig wlan0 0.0.0.0 sudo ipconfig eth0 0.0.0.0 Once again, the desktop cannot reach the ADSL/wireless router. I suspect that I'm missing some simple important step. Can anyone shed some light on this for me?

    Read the article

  • Fixing Windows install by connecting its hard drive via USB to a different laptop

    - by Jason
    I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

    Read the article

  • Fixing Windows install by connecting it's hard drive via USB to a different laptop

    - by Jason
    I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

    Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >