Search Results

Search found 35052 results on 1403 pages for 'limited access'.

Page 361/1403 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

• Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

  - by chepukha

  I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

• fail2ban regex working but no action being taken

  - by fpghost

  I have the following snippet of fail2ban configuration on Ubuntu 13.10 server: #jail.conf [apache-getphp] enabled = true port = http,https filter = apache-getphp action = iptables-multiport[name=apache-getphp, port="http,https", protocol=tcp] mail-whois[name=apache-getphp, dest=root] logpath = /srv/apache/log/access.log maxretry = 1 #filter.d/apache-getphp.conf [Definition] failregex = ^<HOST> - - (?:\[[^]]*\] )+\"(GET|POST) /(?i)(PMA|phptest|phpmyadmin|myadmin|mysql|mysqladmin|sqladmin|mypma|admin|xampp|mysqldb|mydb|db|pmadb|phpmyadmin1|phpmyadmin2|cgi-bin) ignoreregex = I know the regex is good, because if I run the test command on my access.log: fail2ban-regex /srv/apache/log/access.log /etc/fail2ban/filter.d/apache-getphp.conf I get a SUCCESS result with multiple hits, and in my log I see entries like 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 301 585 "-" "-" 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpMyAdmin/scripts/setup.php HTTP/1.1" 301 593 "-" "-" Secondly I know email is configured correctly, as each time I service fail2ban restart I get an email for each of the filters stopping/starting. However despite all this no action seems to be taken when one of these requests comes in. No email with whois, and no entries in iptables. What possibly could be preventing fail2ban from taking action? (everything looks in order in fail2ban-client -d and I can see the chains have loaded with iptables -L)

  Read the article

• Spring-mvc project can't select from a particular mysql table

  - by Dan Ray

  I'm building a Spring-mvc project (using JPA and Hibernate for DB access) that is running just great locally, on my dev box, with a local MySQL database. Now I'm trying to put a snapshot up on a staging server for my client to play with, and I'm having trouble. Tomcat (after some wrestling) deploys my war file without complaint, and I can get some response from the application over the browser. When I hit my main page, which is behind Spring Security authentication, it redirects me to the login page, which works perfectly. I have Security configured to query the database for user details, and that works fine. In fact, a change to a password in the database is reflected in the behavior of the login form, so I'm confident it IS reaching the database and querying the user table. Once authenticated, we go to the first "real" page of the app, and I get a "data access failure" error. The server's console log gets this line (redacted): ERROR org.hibernate.util.JDBCExceptionReporter - SELECT command denied to user 'myDbUser'@'localhost' for table 'asset' However, if I go to MySQL from the shell using exactly the same creds, I have no problem at all selecting from the asset table: [development@tomcat01stg]$ mysql -u myDbUser -pmyDbPwd dbName ... mysql> \s -------------- mysql Ver 14.12 Distrib 5.0.77, for redhat-linux-gnu (i686) using readline 5.1 Connection id: 199 Current database: dbName Current user: myDbUser@localhost ... UNIX socket: /var/lib/mysql/mysql.sock -------------- mysql> select count(*) from asset; +----------+ | count(*) | +----------+ | 19 | +----------+ 1 row in set (0.00 sec) I've broken down my MySQL access settings, cleaned out the user and re-run the grant commands, set up a version of the user from 'localhost' and another from '%', making sure to flush permissions.... Nothing is changing the behavior of this thing. What gives?

  Read the article

• ADSL Modem/Router sometimes hands out incorrect IP addresses

  - by Peter Keevill

  My setup is as follows:- Main ADSL modem / router (switch) configured as DHCP server with address range 192.168.0.25-60 The office machines are configured with fixed IP ( not in the same address pool of course ) and hard wired to this router. A wireless access point ( Router ) is connected to provide Internet access for guests in a separate area. This router is NOT configured as a DHCP server. Wireless authentication is turned off. IP address lease times are set to 4 hours. Sometimes guests are able to connect to the wireless access point but they are not given a valid IP. They get 169.x.x.x addresses. Rebooting their machines does not resolve the problem. The only way to resolve is to reboot the main ADSL/router which is often frustrating for other users who are successfully connected with valid IP and DG. The problem seems to occur more frequently to Apple/Mac guests although it also sometimes occurs with Win machines. I personally use Ubuntu on my Laptop and thus far, never have had any problem connecting and getting a valid IP address in the guest area. One further point of note which may give a clue is that certain guests ( always Apple/Mac ) get lease times of 90 days. However, this does not 'stack out' the number of available addresses and of course, rebooting the router clears them until the next time they login.

  Read the article

• Apache runs in console but not as a service?

  - by danspants

  I have an apache 2.2 server running Django. We have a network drive T: which we need constant access to within our Django app. When running Apache as a service, we cannot access this drive, as far as any django code is concerned the drive does not exist. If I add... <Directory "t:/"> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> to the httpd.conf file the service no longer runs, but I can start apache as a console and it works fine, Django can find the network drive and all is well. Why is there a difference between the console and the service? Should there be a difference? I have the service using my own log on so in theory it should have the same access as I do. I'm keen to keep it running as a service as it's far less obtrusive when I'm working on the server (unless there's a way to hide the console?). Any help would be most appreciated.

  Read the article

• debugging connection to mysql from python script using MySQLdb

  - by timpone

  I am a python newbie and have a python 2.5 script that is using MySQLdb to connect on OS X 10.5.8. I haven't been able to succesfully connect to the database of interest with this. However, I am able to connect using php's mysqli and also via the mysql cli interface. I get the error: File "build/bdist.macosx-10.5-i386/egg/MySQLdb/connections.py", line 188, in __init__ _mysql_exceptions.OperationalError: (1045, "Access denied for user 'arc_development'@'localhost' (using password: YES)") On my linux box which has the same mysql perms, the script works fine logging in. On my OS X laptop, I am able to create a database named test_python which bypasses mysql authentication scheme. This makes me think that issues like 32bit / 64bit incompatabilities aren't occuring. If I turn on the query log, I get access denied: 100610 20:56:55 4 Connect Access denied for user 'arc_development'@'localhost' (using password: YES) I'm a little bit at a loss to what to do next. Is there any way I can specify in the general log or binary log to get the actual password set on the connection string? How about writing out from connections.py file the value (although not sure how I'd do that)? thanks

  Read the article

• How to clone MySQL DB? Errors with CREATE VIEW/SHOW VIEW privileges

  - by user38071

  Running MySQL 5.0.32 on Debian 4.0 (Etch). I'm trying to clone a WordPress MySQL database completely (structure and data) on the same server. I tried doing a dump to a .sql file and an import into a new empty database from the command line, but the import fails with errors saying the user does not have the "SHOW VIEW" or "CREATE VIEW" privilege. Trying it with PHPMyAdmin doesn't work either. I also tried doing this with the MySQL root user (not named "root" though) and it shows an "Access Denied" error. I'm terribly confused as to where the problem is. Any pointers on cloning a MySQL DB and granting all privileges to a user account would be great (specifically for MySQL 5.0.32). The SHOW GRANTS command for the existing user works (the one who has privileges over the source database). It shows that the user has all privileges granted. I created a new user and database. Here's what I see with the grant commands. $ mysql -A -umyrootaccount --password=myrootaccountpassword mysql> grant all privileges on `newtarget_db`.* to 'newtestuser'@'localhost'; ERROR 1044 (42000): Access denied for user 'myrootaccount'@'localhost' to database 'newtarget_db' mysql> grant all privileges on `newtarget_db`.* to 'existingsourcedbuser'@'localhost'; ERROR 1044 (42000): Access denied for user 'myrootaccount'@'localhost' to database 'newtarget_db'

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• Why the VPN Network Shake-Up?

  - by Brent Arias

  I can RDP to another machine on my home network, only if I'm not also hooked up to my employer's VPN with the Cisco VPN client. Indeed, I can't even ping the other machine by name in this mode, because ICMP suddenly thinks that ( ping myMachine ) now means ( ping myMachine.myEmployer.com ). Of course there is no machine by that latter name, and so it fails. Even weirder, once I disconnect from the VPN I can again ping myMachine successfully, but ICMP reports the machine by its MAC address instead of its IP address. I don't think I've ever seen ping identify another machine by its MAC address. So two questions: How can I access via RDP/ping the other machine BY NAME on my local network while also connected to the VPN? Why is ping identifying a MAC address for the machine on my home network, instead of an IP address? And how can I change this so that an IP address is reported instead? For question #1, I can indeed access the other machine on my home network by IP address. I suspect if I put the name-IP pair into my HOSTS file, then I would be able to access it even when connected to the VPN. But I wonder if there is another (more elegant) solution?

  Read the article

• SFTP, Chroot problems on Redhat

  - by Curtis_w

  I'm having problems setting up sftp with a ChrootDirectory. I've done an equivalent setup on other distros, but for some reason I cannot get it to work on a Redhat AMI. The changes to my sshd_config file are: Subsystem sftp internal-sftp Match Group ftponly PasswordAuthentication yes X11Forwarding no ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I have the concerned usere's homes at /home/user, owned by root. After connecting with a user in the ftponly group, I'm dropped into / without permissions for anything, and am unable to do anything. sftp bob@localhost Connecting to localhost... bob@localhost's password: sftp> pwd Remote working directory: / I can connect normally with users not in the ftponly group. openssh version 5.3 I've experimented with different permissions, as well as having users own their own home directory (gives a Write failed: Broken pipe error), and so far, nothing has seemed to work. I'm sure it's a permissions error, or something equally as trivial, but at this point my eyes are beginning to glaze over, and any help would be greatly appreciated. EDIT: James and Madhatter, thanks for clarifying. I was confused by chroot dropping me in /... just didn't think through it properly. I've added the appropriate directories and permissions to get read access. One other key part was enabling write access to chrooted homes: setsebool -P ssh_chroot_rw_homedirs on in order to get write access. I think I'm all set now. Thanks for the help.

  Read the article

• Block users from Social networking websites while firewall is down

  - by SuperFurryToad

  We currently have a SonicWall firewall, which does a pretty good job a blocking Social networking websites like Facebook and Bebo. The problem we are having is that sometimes we need to temporarily disable our firewall blocklist so we can update our company's page on Facebook for example. Whenever we do this, have see an avalanche of users logging on to their Facebook pages during work time. So what we need a way to block access while the firewall is down. For the sake of argument, we have two groups of users - "management" and "standard users". "standard users" would have no access to Facebook, but "management" users would have access. Perhaps something like a host file redirect for non-management users. This could probably be enforced via group policy that would call a bat file to copy down the host file, depending if the user was management or not. I'm keen to hear any suggestions for what the best practice would be for this in a Windows/AD environment. Yes, I know what we're doing here is trying to solve a HR problem using IT. But this is the way management wants it and we have a lot of semi-autonomous branch offices that we don't have a lot of day to day contact with, so an automated way of enforcing this would be the most preferable method.

  Read the article

• Setting up squid proxy server to in turn connect using another proxy server [closed]

  - by AnkurVj

  My institute uses the Squid proxy server and authentication mechanism requires username and password to be entered. This means that, I can log in on only one machine at a time and Internet access for me is restricted to that machine. I sometimes require Internet access on multiple machines simultaneously. What previosuly worked for me was the following : On one of my own machines A, I set up a Squid proxy server that allowed all local machines without any username and password. I configured rest of the machines to use this machine A as the proxy server. On machine A I logged into the institute proxy server using my browser. This way, I could access Internet from all my machines, by effectively channeling my requests through the server A. Recently, I lost that machine and configuration and now I tried to set it up again in the same manner. However, I cant seem to remember exactly how I made it work. I keep getting Connection Refused (111) on other machines. My guess is that my squid server isnt able to forward requests from other machines to the actual squid server. I could use any help for debugging this problem. I don't want to use alternatives such as ssh tunneling. This solution has worked for me in the past, I just don't remember how to set it up the same way again.

  Read the article

• Running phpmyadmin xampp Ubuntu 12.10

  - by Luigi Tiburzi

  I know it is a common problem and there are many solutions on the web but I'm trying everything and anything is working, I can't have phpmyadmin running on my machine. I installed XAMPP through: sudo tar xvfz ./Downloads/xampp-linux-1.8.1.tar.gz -C /opt then I did the chmod trick supposed to make an end to access issues and I change the default location to my php projects from /var/www to Dropbox/php. Then I started XAMPP in the usual way: sudo /opt/lampp/lampp start When I tried to run one of my php projects the output on the web is fine but if for example I try to write localhost on my browser I get: It works and not the usual XAMPP interface and most of all when I try to access localhost/phpmyadmin I get the login page, insert username (root) and password and I get: You don't have permission to access /phpmyadmin/index.php on this server. Apache/2.2.22 (Ubuntu) Server at localhost Port 80 I tried the Required all granted trick and some others but nothing is working. I even tried to uninstall phpmyadmin and reinstall it but this is not working too. I don't know hot to proceed. Thanks for your help.

  Read the article

• Setting the default permissions for files uploaded via FTP to a directory

  - by Kerri

  Disclaimer: I'm just a web designer/coder, and server admin stuff is my weakest point of them all. So be easy on me (and very specific). I'm using a simple CMS (Unify) on a site, where part of the functionality is that the client can upload files to a specified directory (using FTP). The permissions for the upload directory are set to 755. But when files are uploaded through the interface, they are uploaded with permissions set to 640 (instead of 644), so site visitors cannot acces the files. When I emailed the CMS's support about this, they told me that it was a server setting, and I need to make sure that files uploaded through FTP are set to 644. Makes perfect sense, but I have no idea how to do this. Any help would be greatly appreciated. This site is a shared site hosted by Network Solutions (Unix), so my access options are limited. I can edit .htaccess files, and php.ini, but that's about all I have access to. It appears I can't even log on via shell. ETA: 11/11/2010 Thanks all. I was able to work around this problem by setting up the CMS's settings in a different way. I'd be interested in following up on Nick O'Niel's suggestions, because I think he's on the right track, but unfortunately I can't access the necessary files on this particular server. So, anyway, I'm leaving this open, since the original questions isn't exactly resolved. Unfortunately, I probably can't put a correct answer to the test, since the shared server in question has nearly all of its config files tightly locked down.

  Read the article

• Windows 2008 R2 RDS - Double Login

  - by colo_joe

  Issue: Double logins when connecting to RemoteApps or Remote Desktop Environment: Gateway = 1 server 2008 R2 - Roles = Gateway, Session Broker, Connection Mgr, Session Host Configuration server Session hosts = 2 servers 2008 R2 - Roles = App Manager and Session host configuration Testing: I can get to the url http://RDS.domain.com/rdweb - I get prompted for authentication (1) Pass authentication, get list of remote apps. Click on remoteapps or remote desktop, get prompted for authentication again (2). Pass authentication, I get access to app or RDP. Done so far. On session host Signed rdp files with cert. Added the following to the custom RDP settings: Authenticaton level:i:0 = If server authentication fails, connect to the computer without warning (Connect and don’t warn me). prompt for credentials on client:i:1 = RDC will prompt for credentials when connecting to a server that does not support server authentication. enablecredsspsupport:i:1 = RDP will use CredSSP, if the operating system supports CredSSP. Edited the javascript file as found in http://support.microsoft.com/kb/977507 Added Connection ID, and added Web Access server to TS Web Access Computers group on the Session host servers, and Signed apps as found in hxxp://blogs.msdn.com/b/rds/archive/2009/08/11/introducing-web-single-sign-on-for-remoteapp-and-desktop-connections.aspx Note: This double login happens internally and externally.

  Read the article

• VLAN for WiFi traffic separation (new to VLANing)

  - by Philip

  I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

  Read the article

• Secure data from a server to a workstation using jumper hosts

  - by apalsson

  Hello. I have a WWW-server, my problem is that the content is sensitive and should not be accessible for people without proper credentials. How can I improve the ease of use but still maintain security following scenario; The Server is accessed through a "jumper host", i.e. the client connects to the jumper using VPN-connection and uses RemoteDesktop to access the jumper. From the jumper he uses RemoteDesktop again to access the Server. Finally on the Server the user can access content using a WWW-browser. All the way from the VPN-client to the WWW-browser requires authentication using a SmartCard-token. This seems quite secure to me. Content only gets mirrored on the RemoteDesktop between Server and jumper, no cached files to worry about. Connection between jumper and client is protected using VPN(ssl), so no eavesdropping. But it is quite cumbersome for the clients with many steps and connections to open. :( So, how can I improve the user experience accessing my server without compromising security? Thanks.

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• How to setup NTFS ACL with Acces Based Enumeration

  - by Patrick Pellegrino

  We're in the process of migrating from Novell Netware to Windows 2K8 R2 infrastructure (AD, File server, print server... etc) My question is about ACL. While Netware and Windows are totally different, I want to be sure my thnking is good before screwing everything up! There's a scenario : F: | +-- DATA <= Shared as DATA with Access based enumeration | +-- Folder 1 +-- Team 1's Folder +-- Team 2's Folder ... In that case, by default, rights are herited from the F: to the deepest folders. What we want : Administrators group have full control top - down. From DATA, ABE list only folders that users have access. (ex. : I'm in group Team 2, I see Team 2's Folder). From what I understand, at DATA I remove all NTFS ACL to be herited (ex. Users Group), be sure to keep Administrators Group and SYSTEM user. After that, grant Full control (or any right needed) on each folder to Groups or Users that have to have access. Does I'm wrong ? Anything I should take care of ? Any help to my understanding will be very appreciated. Regards.

  Read the article

• Getting Win32_Service security descriptor using VBScript

  - by invictus

  Hi, I am using VbScript for retrieving the securitydescriptor of a Win32_Service. I am using the following code: SE_DACL_PRESENT = &h4 ACCESS_ALLOWED_ACE_TYPE = &h0 ACCESS_DENIED_ACE_TYPE = &h1 strComputer = "." Set objWMIService = GetObject("winmgmts:" _ & "{impersonationLevel=impersonate, (Security)}!\\" & strComputer & "\root\cimv2") Set colInstalledPrinters = objWMIService.ExecQuery _ ("Select * from Win32_Service") For Each objPrinter in colInstalledPrinters Wscript.Echo "Name: " & objPrinter.Name ' Get security descriptor for printer Return = objPrinter.GetSecurityDescriptor( objSD ) If ( return <> 0 ) Then WScript.Echo "Could not get security descriptor: " & Return wscript.Quit Return End If ' Extract the security descriptor flags intControlFlags = objSD.ControlFlags If intControlFlags AND SE_DACL_PRESENT Then ' Get the ACE entries from security descriptor colACEs = objSD.DACL For Each objACE in colACEs ' Get all the trustees and determine which have access to printer WScript.Echo objACE.Trustee.Domain & "\" & objACE.Trustee.Name If objACE.AceType = ACCESS_ALLOWED_ACE_TYPE Then WScript.Echo vbTab & "User has access to printer" ElseIf objACE.AceType = ACCESS_DENIED_ACE_TYPE Then WScript.Echo vbTab & "User does not have access to the printer" End If Next Else WScript.Echo "No DACL found in security descriptor" End If Next However, every time I run it I get the message saying the resulting code is -2165236532 something, rather than the error codes defined in the manual. Anyone got any ideas? I am using Windows 7 professional.

  Read the article

• Mavericks permission issues with Windows Server deduplicated shares

  - by dmohlmaster

  We have a number of 10.9-10.9.3 - Mavericks - machines installed throughout our facility. Much of the user content is pulled from shares stored on our Windows Server 2012 fileservers with deduplication enabled. I have found that files newly written or unoptimized are able to be accessed without issue - read, written, modified, etc. Once the file gets optomized/deduplicated and Windows adds the P & L attributes - sparse and symlink - the Macs running Mavericks begin to have access issues. Once the files get deduplicated, users begin receiving read access errors when copying files (see error1 below). This happens when copying to folders within the current folder tree or copying somewhere to the local system. If you 'stop' the copy operation and retry a few more times, it may eventually work for the specific instance but fail again later. I am however, able to copy these files without issue via the terminal. Other systems running 10.7 do not experience the same issues and are able to access file server resources without issue. Many of the systems having issues are newer and thus not able to be downgraded to 10.8 or 10.7. I have tried finder replacements such as Pathfinder but the results are the same. I know this is at least similar to the issues many Mac users are already experiencing and posting about but I haven't seen it directly linked to deduplication and the attributes written by Windows server. Has anyone seen this issue? Have any solutions been found? Error 1: When copying files after the PL attributes have been set by deduplication. "One or more items can't be copied to "Foler" because you don't have permissions to read them. ******************************************' Via the system.log, I am also seeing the following error when accessing these deduplicated file shares. The reparse point tag listed below is "IO_REPARSE_TAG_DEDUP" Reported error: "smbfs_nget: filename.ext - unknown reparse point tag 0x80000013"

  Read the article

• OpenLDAP ACLs are not working

  - by Dr I

  First things first, I'm currently working with an OpenLDAP: slapd 2.4.36 on a Fedora release 19 (Schrödinger’s Cat). I've just install the openldap with yum and my configuration is the following one: ##### OpenLDAP Default configuration ##### # ##### OpenLDAP CORE CONFIGURATION ##### include /etc/openldap/schema/core.schema include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema pidfile /var/lib/ldap/slapd.pid loglevel trace ##### Default Schema ##### database mdb directory /var/lib/ldap/ maxsize 1073741824 suffix "dc=domain,dc=tld" rootdn "cn=root,dc=domain,dc=tld" rootpw {SSHA}SECRETP@SSWORD ##### Default ACL ##### access to attrs=userpassword by self write by group.exact="cn=administrators,ou=builtin,ou=groups,dc=domain,dc=tld" write by anonymous auth by * none I launch my OpenLDAP service using: /usr/sbin/slapd -u ldap -h ldapi:/// ldap:/// -f /etc/openldap/slapd.conf As you can see it's a pretty simple ACL which aim to allow access to the userPassword attribute to a specific group read only, then to the owner read and write to anonymous requiring auth and refuse the access to everyone else. The problem is: Even using a valid user with correct password my ldapsearch ends with zero informations retrieved from the directory, plus I've got a strange response on the result line. # search result search: 2 result: 32 No such object # numResponses: 1 here is the ldapsearch request: ldapsearch -H ldap.domain.tld -W -b dc=domain,dc=tld -s sub -D cn=user,ou=service,ou=employees,ou=users,dc=domain,dc=tld I did not specify any filter as I want to check that ldapsearch is correctly printing only allowed attribute.

  Read the article

• How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment [closed]

  - by lmttag

  Possible Duplicate: How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment We have an ASP.NET Web API server that serves up a SQL Server data driven website. The API uses JSON to transfer data from SQL Server to the front end. We need to move it to an internal production environment (nothing will be exposed on the public Internet) and we’re having problems - or just not understanding what needs to be done. There are two domains: The corporate domain - where all users login normally. The process domain - contains the database the Web API needs to access. The IT staff wants to put a DMZ between the two domains to house the IIS app and shield the users on the corporate domain from having access into the process domain directly. The ideal configuration is: corp domain (end users) <–> firewall (open port 80) <–> DMZ (web server running IIS) <–> firewall (open port 80 or 1433????) <–> process domain (IIS for Web API and SQL Server) We don’t really understand how to deploy our browser/Web API application in this scenario. Do we need to break up our application so that all the client code is on the IIS server in the DMZ, while the Web API gets installed on the server in the process domain? Does the entire app (client code and Web API) stay together on the IIS server in the DMZ, which then somehow accesses the SQL Server instance to get data? From the IIS server and app in the DMZ, would you simply access the Web API on the server in the process domain by going to http://server/appname/api/getitmes? In the second firewall between the DMZ and the process domain, would you have to open port 1433 or just port 80 since the Web API is a HTTP endpoint? Or, is there some better way of deployment (i.e., how ASP.NET Web API single page applications written all in HTML5 and JavaScript supposed to be deployed to production environments?)? NB: The servers are Win2k8 R2, SQL Server 2k8 R2, and IIS 7.5.

  Read the article

• Sharepoint Central Administration stuck / high CPU usage

  - by johnnyb10

  I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

  Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >