Search Results

Search found 15930 results on 638 pages for 'analysis services'.

Page 365/638 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

  • Wrapping a point-to-point link

    - by user3712955
    I'm using a pair of IP radios (non-WiFi) to bridge my office engineering LAN (172.0.0.0/8) to a lab in another building. The radios work fine, but they expose a web management interface I'd like to hide, and they also generate traffic (ARP, STP, and more) that I need to keep off my (very, very clean) LAN segments. I have some ARM-Linux boards (similar to Beagle/Panda/RasPi) running Ubuntu, and I've put one at each end of the link, between the radio and the LAN. Each of the boards has 2 wired Ethernet interfaces, eth0 and eth1. The LAN segments are connected to eth0, and the radios are connected to eth1. I'd like to accomplish the following: Keep radio-originated traffic off my LAN segments! Hide all services provided by the radio (web, ssh, etc.) Transparently pass all traffic between the LAN segments (including things like ARP). The above also applies to the ARM-Linux boards: No stray traffic my LAN from them either! I'd like the system to look like a switch: LAN packets arriving at one eth0 appear at the other. And neither eth0 should have an IP address: The working system should behave like a CAT6 cable with some latency (instead of ARM boards and radios). Unfortunately, I'm confused about how to properly configure the ARM Ubuntu systems. What I'm guessing I need is a bridge on each board (br0?) and a VLAN (vlan0 or eth0.0?) to isolate the LAN traffic from everything else as it passes through the ARM boards and the radios. Then I need some kind of a firewall to block sending anything out eth0 that isn't from the other eth0 (via the VLAN). I've looked at the ip and ebtables commands (especially -t broute). While the concepts sorta-kinda make sense, I'm completely lost in the details. Edit: In the perverse case that a system on one of my LAN segments has the same IP address as one of the radios, or as eth1 on the ARM-Ubuntu boards, a VLAN won't work. Which I believe means I need to tunnel all traffic between the two eth0 interfaces to get that "like a wire" behavior. Help? Finally, I'd like to have a way to temporarily expose services on the ARM boards (ssh) and the radios (web) for maintenance purposes. Ideally, it would expose an IP address with ssh available on port 22. Once connected, I figure I'd start an X11 session and run a browser on the ARM board to access the radios. Or something. I could login via the console to enable/disable this, or perhaps could use a GPIO to trigger a script. I feel I've identified most of the pieces needed to make all this happen, but I have no idea how to combine them to make a working system. Thanks!

    Read the article

  • Do I need a SMTP server for my domain to receive email?

    - by ashkanr
    my domain has a domain extension that since my country is not supported by Google Apps I can't use that lovely GApps services for that domain. I need free email service of GApps the most, so I decided to give a go to "Send mail as" feature of a regular Gmail account and add my domain emails to that personal Gmail. I have a question: Do I need a SMTP server for my domain to receive email from others? Thanks in advance :)

    Read the article

  • Why is RAM usage so high on an idle server? [duplicate]

    - by DeeDee
    This question already has an answer here: Why is Linux reporting “free” memory strangely? 2 answers I'm investigating a server used for scientific data analysis. It's running RHEL 6.4 It has almost 200GB of RAM. It's been running very slowly for users via SSH, and after some poking around I quickly noticed that the RAM usage was sky-high. What's odd is that even in an idle state it's still using a ton of RAM: I also looked via htop and I can't see that any running process is using more than 0.1% of the RAM. So I wonder what's going on? Right now the only user-initiated process running is an rsync between two NFS-mounted shares. I tried rebooting the server and it was much more responsive for a few minutes, but then memory usage shot up again. Is there any way I can pinpoint why memory usage is so high?

    Read the article

  • Juniper Network Connect (VPN) on Windows 7

    - by Virat Kadaru
    My company uses Juniper networks for vpn access. I am unable to get the juniper network connect client to work on windows 7 64-bit. It used to work before but after I formatted my system it gives the following error every time I start the vpn client If I check the logs I see this error The Juniper Network Connect Service service is marked as an interactive service. However, the system is configured to not allow interactive services. This service may not function properly.

    Read the article

  • How to access files on another local Windows 7 computer without using any native Windows features?

    - by user1356682
    I do not want to use any native Windows features, services, nor anything do to this. It needs to be a standalone program, with ZERO Windows dependencies. Just like TeamViewer does not use any native Windows features, so I want to be able to access files and folders in a standalone program. No remote desktop No VNC type programs No Windows File Sharing No Shared Folders in Windows No internet connection required It needs ability to view, edit, transfer files at normal network rates.

    Read the article

  • Why is Internet said to be an untrusted network?

    - by Ant's
    From Wikipedia In computer security, a DMZ (sometimes referred to as a perimeter networking) is a physical or logical subnetwork that contains and exposes an organization's external services to a larger untrusted network, usually the Internet. Why does it say … larger untrusted network, usually the Internet. I often see that internet is said to be an untrusted network. Are there any reasons for it?

    Read the article

  • Windows Process Activation Service won't Start "parameter is incorrect" (Visual Studio 2010 Profiler)

    - by user23596
    I've struggled with this one for a whole day, so here is both the problem & solution: After profiling an ASP.NET application on Windows 7 (x64), I exited Visual Studio (possibly a crash) and installed some updates which required a reboot. When I loaded back up the ASP.NET Web Application in my Visual Studio Solution was dimmed out, and the Web & WAS services turned out to be stopped. When I tried starting Windows Process Activation Service, I got the error "parameter is incorrect".

    Read the article

  • What is the BRU Server Disaster Recovery Procedure?

    - by Jonskichov
    How do I go about performing a full, bare metal disaster recovery from BRU Server backups? I have backed up the entire C:\ (including Windows, Program Files etc) of a test machine (using Open File Manager) and want to restore this to a new server. What is the procedure I need to go through to restore to a clean server using my backup? How does this work with various services such as DHCP, DNS, Active Directory, SQL Server, Windows Registry etc? Thanks in advance.

    Read the article

  • is Drupal good business POS [on hold]

    - by mavili
    I've got to work on a POS-type web application for a money transfer, shipping, and other customer services like translation and help-out charges. I was planning to do that in pure PHP without frameworks or CMS's, but then Drupal came into play and I'm wondering if I should learn Drupal and do the app with it. My question is, is Drupal good for such a work, and if it is will it take me more than a week to learn enough to make it possible? For info, I'm a decent PHP programmer.

    Read the article

  • Are there any legal issues while extracting content from RSS feeds? [closed]

    - by Kalinga
    I would like to know whether these free SMS alert sites such as My Today SMS, Alertix pay for the sites such as religate, oneindia.in e.t.c, Or they just mention in their website that this service powered by Oneindia. What I would like to know is whether these people pay any royalty/monthly/annual fee for these religate/oneindia, by which I also mean: Are there any legal issues attached to extracting data from the RSS feeds these websites provide for services like free SMS alerts?

    Read the article

  • Windows 7 and VMware Server

    - by DRamos
    Hi, I've just downloaded the latest VMware server from vmware site, and after installing it under Windows 7 Ultimate x64 I check that the services are running ok. Problem is I can't access the web interface to manage the VMs.. Any help with it?

    Read the article

  • wcf - maximum array length quota

    - by dav.evans
    Im writing a small wcf/wpf app to resize images but wcf is giving me grief when I try to send an image of size 28K to my service from the client. The service works fine when I send it smaller images. I immediately assumed that this was a configuration issue and I've trawled the web looking at posts regarding the MaxArrayLength property in my binding configuration. Ive upped the limits on these settings on both the client and server to the maximum 2147483647 but still I get the following error: {"The formatter threw an exception while trying to deserialize the message: There was an error while trying to deserialize parameter http://mywebsite.com/services/servicecontracts/2009/01:OriginalImage. The InnerException message was 'There was an error deserializing the object of type System.Drawing.Image. The maximum array length quota (16384) has been exceeded while reading XML data. This quota may be increased by changing the MaxArrayLength property on the XmlDictionaryReaderQuotas object used when creating the XML reader.'. Please see InnerException for more details."} Ive made my client and server configs the same and they look like the following: Server: <system.serviceModel> <bindings> <netTcpBinding> <binding name="NetTcpBinding_ImageResizerServiceContract" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" transactionFlow="false" transferMode="Buffered" transactionProtocol="OleTransactions" hostNameComparisonMode="StrongWildcard" listenBacklog="10" maxBufferPoolSize="2147483647" maxBufferSize="2147483647" maxConnections="10" maxReceivedMessageSize="2147483647"> <readerQuotas maxDepth="32" maxStringContentLength="2147483647" maxArrayLength="2147483647" maxBytesPerRead="2147483647" maxNameTableCharCount="2147483647" /> <reliableSession ordered="true" inactivityTimeout="00:10:00" enabled="false" /> <security mode="Transport"> <transport clientCredentialType="Windows" protectionLevel="EncryptAndSign" /> <message clientCredentialType="Windows" /> </security> </binding> </netTcpBinding> </bindings> <behaviors> <serviceBehaviors> <behavior name="ServiceBehavior"> <serviceMetadata httpGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="false" /> </behavior> </serviceBehaviors> </behaviors> <services> <service name="LogoResizer.WCF.ServiceTypes.ImageResizerService" behaviorConfiguration="ServiceBehavior"> <host> <baseAddresses> <add baseAddress="http://localhost:900/mex/"/> <add baseAddress="net.tcp://localhost:9000/" /> </baseAddresses> </host> <endpoint binding="netTcpBinding" contract="LogoResizer.WCF.ServiceContracts.IImageResizerService" /> <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange"/> </service> </services> </system.serviceModel> and my client config looks like: <system.serviceModel> <bindings> <netTcpBinding> <binding name="NetTcpBinding_ImageResizerServiceContract" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" transactionFlow="false" transferMode="Buffered" transactionProtocol="OleTransactions" hostNameComparisonMode="StrongWildcard" listenBacklog="10" maxBufferPoolSize="2147483647" maxBufferSize="2147483647" maxConnections="10" maxReceivedMessageSize="2147483647"> <readerQuotas maxDepth="32" maxStringContentLength="2147483647" maxArrayLength="2147483647" maxBytesPerRead="2147483647" maxNameTableCharCount="2147483647" /> <reliableSession ordered="true" inactivityTimeout="00:10:00" enabled="false" /> <security mode="Transport"> <transport clientCredentialType="Windows" protectionLevel="EncryptAndSign" /> <message clientCredentialType="Windows" /> </security> </binding> </netTcpBinding> </bindings> <client> <endpoint address="net.tcp://localhost:9000/" binding="netTcpBinding" bindingConfiguration="NetTcpBinding_ImageResizerServiceContract" contract="ImageResizerService.ImageResizerServiceContract" name="NetTcpBinding_ImageResizerServiceContract"> <identity> <userPrincipalName value="[email protected]" /> </identity> </endpoint> </client> </system.serviceModel> It seems no matter what I set these values to I still get an error saying wcf cannot serialize my file because its greater than 16384. Any ideas? edit: the email address in the userPrincipalName tag has been altered for my privacy

    Read the article

  • Ajax, Lizard Brain Web Design, JSF, Struts, JavaScript, Mobile Web, Flash, jQuery, GWT, Harmony at I

    - by Kim Won
    Great Indian Developer Summit 2010 – India's Biggest Polyglot Conference and Workshops for IT Software Professionals Bangalore, April 9, 2010: The GIDS.Web Conference and Workshops has announced the complete program of over 30 sessions on how browser and rich web technologies such as AJAX, DHTML, Mashups, Web 2.0, Enterprise 2.0 technologies, and Rich UI technologies are making money and gaining market-share for some of the leading businesses in the world. The GIDS.Web track at Great Indian Developer Summit takes place 21 and 23 April 2010, at the Indian Institute of Science in Bangalore. As one of the longest running independent developer conferences in India, GIDS.Web at the Great Indian Developer Summit 2010 is uniquely positioned to provide a blend of practical, pragmatic and immediately applicable knowledge and a glimpse of the future of technology. During 21 and 23 April 2010, GIDS.Web offers a multi-track conference, workshops, expo show floor, and networking opportunities. The first keynote at GIDS.Web is led by the leading Java EE and Ajax developer, speaker, and author Marty Hall. The best of India's Java and RIA programmers have learnt the subject from Marty's seminal books Core Servlets and JavaServer Pages (first and second editions), More Servlets and JavaServer Pages, and Core Web Programming (first and second editions) from Prentice Hall and Sun Microsystems Press. Marty's keynote address is a comparison of approaches to building rich Internet applications with Ajax. Marty says Ajax development is difficult, and there are several fundamentally different strategies to building Ajaxified Web applications. The keynote address will survey the three most important of these approaches: using an Ajax-enabled JavaScript library such as jQuery, Prototype, Scriptaculous, Dojo, or Ext/JS; using a Web framework such as JSF 2.0 or Struts 2 that has integrated Ajax support; using the Google Web Toolkit (GWT) to build "pure Java" Ajax applications. The talk will compare and contrast these three approaches, discussing the types of applications that fit best for each option. Over the course of the summit Marty will conduct several more sessions on "Choosing an Ajax/JavaScript Toolkit: A Comparison of the Most Popular JavaScript Libraries", "Pure Java Ajax: An Overview of GWT 2.0", "Integrated Ajax Support in JSF 2.0" and "Ajax Support in the Prototype JavaScript Library". The second keynote by the head of Adobe's Flash initiative in India, Ramesh Srinivasaraghavan, explores the state of art in web application development and identify trends that could transform the way we create and use web applications. The talk explains how the Adobe Flash Platform has fuelled this revolution with an integrated set of technologies for delivering the most compelling applications, content and video to the widest possible audience. The Director of Forum Nokia will explain how cloud computing coupled with mobile applications enable consumers to have access to powerful services and improved user experiences never before thought possible. IEEE's 2010 President-Elect Sorel Reisman's afternoon address steps to improve the IT profession in India. Featured talks at GID.Web also include: Web 2.0 Checklist - Deconstructing Modern Websites, Scott Davis Choosing an Ajax/JavaScript Toolkit: Comparison of Popular JavaScript Libraries, Marty Hall Lizard Brain Web Design, Scott Davis Effective Design Processes and Resources for Mobile Web Development, Arabella David NoSQL: The Shift to a Non-relational World, Nosh Petigara Open Source Web Debugging Tools, Matthew McCullough Building Line of Business Applications with Silverlight 4.0, Stephen Forte Hadoop - Divide and Conquer, Matthew McCullough Adobe Flash Catalyst for Agile Interaction Design, Harish Sivaramakrishnan Using jQuery and AJAX to Build Front-ends for ASP.NET and ASP.NET MVC, Pandurang Nayak First Steps to IT Heaven Through the Cloud. Part II: .WEB, Simone Brunozzi Building Rich Internet Applications with SL RIA Web Services, Pandurang Nayak Enriching Cloud Applications with Adobe Flash Platform, Ramesh Srinivasaraghavan Payments for the Web.future, Khurram Khan and Praveen Alavilli Longevity of Scalable Systems, Nishad Kamat Transform yourself into a Mobile App Developer Using Web Run Time, Balagopal K S Developing Multi Screen Applications on Adobe Flash Platform, Hemanth Sharma Why Harmony and For Whom?, Himanshu Goyal IIS Hosting Solution for ASP.net and PHP Web Sites, Nahas Mohammed Building Pluggable Web applications using Django, Lakshman Prasad Workshop: The 180-min AJAX and JSON Spike Class, Scott Davis Workshop: Essence of Functional Programming, Venkat Subramaniam Workshop: Agile Development, Tools, and Teams and Scrum Certification, Stephen Forte Workshop: PHP + Adobe Flex = Killer RIA, Shyamprasad P Workshop: Cloud Computing Boot Camp on the Google App Engine, Matthew McCullough Workshop: Building Data Centric Applications using Adobe Flex and Java, Prashant Singh Workshop: Building Your First Amazon App, Simone Brunozzi Workshop: Windows Azure Deep Dive, Ramaprasanna Chellamuthu Workshop: Monetizing your Apps with PayPal X Payments Platform, Khurram Khan, Praveen Alavilli Workshop: User Expereince Evaluation Model Walkthrough, Sanna Häiväläinen Sponsors of Great Indian Developer Summit 2010 include: Platinum sponsors Microsoft, Oracle Forum Nokia and Adobe; Gold sponsors Intel and SAP; Silver sponsors Quest Software, PayPal, Telerik and AMT. About Great Indian Developer Summit Great Indian Developer Summit is the gold standard for India's software developer ecosystem for gaining exposure to and evaluating new projects, tools, services, platforms, languages, software and standards. Packed with premium knowledge, action plans and advise from been-there-done-it veterans, creators, and visionaries, the 2010 edition of Great Indian Developer Summit features focused sessions, case studies, workshops and power panels that will transform you into a force to reckon with. Featuring 3 co-located conferences: GIDS.NET, GIDS.Web, GIDS.Java and an exclusive day of in-depth tutorials - GIDS.Workshops, from 20 April to 24 April at the IISc campus in Bangalore. At GIDS you'll participate in hundreds of sessions encompassing the full range of Microsoft computing, Java, Agile, RIA, Rich Web, open source/standards, languages, frameworks and platforms, practical tutorials that deep dive into technical skill and best practices, inspirational keynote presentations, an Expo Hall featuring dozens of the latest projects and products activities, engaging networking events, and the interact with the best and brightest of speakers from around the world. For further information on GIDS 2010, please visit the summit on the web http://www.developersummit.com/ A Saltmarch Media Press Release E: [email protected] Ph: +91 80 4005 1000

    Read the article

  • W3WP crashes when initializing a collection

    - by asbjornu
    I've created an ASP.NET MVC application that has an initializer attached to the PreApplicationStartMethodAttribute. When initializing, a collection is instantiated that implements an interface I've defined. When I instantiate this collection, w3wp.exe crashes with the following two incomprehensible entries in the event log: Faulting application name: w3wp.exe, version: 7.5.7600.16385, time stamp: 0x4a5bd0eb Faulting module name: clr.dll, version: 4.0.30319.1, time stamp: 0x4ba21eeb Exception code: 0xc00000fd Fault offset: 0x0000000000001177 Faulting process id: 0x1348 Faulting application start time: 0x01cb0224882f4723 Faulting application path: c:\windows\system32\inetsrv\w3wp.exe Faulting module path: C:\Windows\Microsoft.NET\Framework64\v4.0.30319\clr.dll Report Id: c6a0941e-6e17-11df-864d-000acd16dcdb And: Fault bucket , type 0 Event Name: APPCRASH Response: Not available Cab Id: 0 Problem signature: P1: w3wp.exe P2: 7.5.7600.16385 P3: 4a5bd0eb P4: clr.dll P5: 4.0.30319.1 P6: 4ba21eeb P7: c00000fd P8: 0000000000001177 P9: P10: Attached files: These files may be available here: Analysis symbol: Rechecking for solution: 0 Report Id: c6a0941e-6e17-11df-864d-000acd16dcdb Report Status: 0 If I remove the instantiation of the collection, the application starts normally. If I leave the instantiation, w3wp crashes. If I modify the interface, w3wp still crashes. I've tried every variation I could come up with on the theme of keeping the instantiation but doing everything else differently, but w3wp still crashes. My biggest issue here is that I have absolutely no idea why w3wp is crashing. It's not a StackOverflowException or anything concrete like that, all I get is the unintelligent junk cited above. I've tried to use DebugDiag and IISState to debug the w3wp process, but DebugDiag is only available for post-dump analysis in x64 (I'm running on Windows 7 x64, so the w3wp process is thus 64 bit) and IISStat says the following when I try to run it: D:\Programs\iisstate>IISState.exe -p 9204 -d Symbol search path is: SRV*D:\Programs\iisstate\symbols*http://msdl.microsoft.com/download/symbols IISState is limited to processes associated with IIS. If you require a generic debugger, please use WinDBG or CDB. They are available for download from http://www.microsoft.com/ddk/debugging. This error may also occur if a debugger is already attached to the process being checked. Incorrect Process Attachment I've double-checked 10 times that the process ID of my w3wp process is correct. I'm suspecting that IISState too only can debug x86 processes. Setting a breakpoint anywhere in the application does absolutely nothing. The break point isn't hit and w3wp crashes as soon as the request comes through to IIS from the browser. Starting the application with F5 in Visual Studio 2010 or starting another application to get the w3wp process up and running and then attaching the VS2010 debugger to it and then visiting the faulting application doesn't help. I've also tried to add an HTTP module as described in KB-911816 as well as add this to my web.config file: <configuration> <runtime> <legacyUnhandledExceptionPolicy enabled="true" /> </runtime> </configuration> Needless to say, it makes absolutely no difference. So I'm left with no way to debug the w3wp process, no way to extract any information from it and complete garbage dumped in my event log. If anybody has any idea on how to debug this problem, please let me know! Update My collection was initialized based on RouteTable.Routes which might have thrown an exception (perhaps by not being initialized itself yet in such an early stage of the ASP.NET lifecycle). Postponing the communication with RouteTable.Routes until a later stage solved the problem. While I don't really need an answer to this question anymore, I still find it so obscure that I'll leave it for anyone to comment on and answer, because I found no existing posts on this problem anywhere, so it might be of good reference in the future.

    Read the article

  • WCF: SecurityNegotiationException when using client

    - by bradhe
    So I've been trying to set up certificate authentication for my clients and services. The eventual goal is to partition data based on the certificate a client connects with (i.e. the certificate becomes their credentials in to the greater system and their data is partitioned based on these credentials). I have been able to set it up successfully on both the client and the server side. I have created a certificate and a private key, installed them on my computer, and set up my server such that 1) it has a certificate-based service credential and 2) if a client connects without providing a certificate-based credential an exception is thrown. What I then did was create a simple client and add a certificate credential to the configuration and try to call a simple operation on the service. It looks like the client connects OK, and it looks like the certificate is accepted by the server, but I do get this: SecurityNegotiationException: "The caller was not authenticated by the service." That seems rather ambiguous to me. Note that I am using wsHttpBinding, which supposedly defaults to Windows auth for transport security...but all of these processes are being run as my user account as I'm running in my debug environment. Here is my server configuration: <system.serviceModel> <bindings> <wsHttpBinding> <binding name="MyServiceBinding"> <security mode="Message"> <transport clientCredentialType="None"/> <message clientCredentialType="Certificate"/> </security> </binding> </wsHttpBinding> </bindings> <services> <service behaviorConfiguration="MyServiceBehavior" name="MyService"> <endpoint binding="wsHttpBinding" bindingConfiguration="MyServiceBinding" contract="IMyContract"/> <endpoint binding="mexHttpBinding" address="mex" contract="IMetadataExchange"> <identity> <dns value="localhost"/> </identity> </endpoint> </service> </services> <behaviors> <serviceBehaviors> <behavior name="MyServiceBehavior"> <serviceMetadata httpGetEnabled="true" policyVersion="Policy15" /> <serviceDebug includeExceptionDetailInFaults="false" /> <serviceCredentials> <serviceCertificate storeLocation="CurrentUser" storeName="My" x509FindType="FindBySubjectName" findValue="tmp123"/> </serviceCredentials> </behavior> </serviceBehaviors> </behaviors> <serviceHostingEnvironment multipleSiteBindingsEnabled="true" /> </system.serviceModel> Here is my client config -- note that I'm using the same cert for the client that I use on the service: <system.serviceModel> <bindings> <wsHttpBinding> <binding name="WSHttpBinding_IMyService" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" bypassProxyOnLocal="false" transactionFlow="false" hostNameComparisonMode="StrongWildcard" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" messageEncoding="Text" textEncoding="utf-8" useDefaultWebProxy="true" allowCookies="false"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384"/> <reliableSession ordered="true" inactivityTimeout="00:10:00" enabled="false"/> <security mode="Message"> <!--<transport clientCredentialType="Windows" proxyCredentialType="None" realm=""/>--> <message clientCredentialType="Certificate" negotiateServiceCredential="true" algorithmSuite="Default"/> </security> </binding> </wsHttpBinding> </bindings> <client> <endpoint address="http://localhost:50120/UserServices.svc" binding="wsHttpBinding" bindingConfiguration="WSHttpBinding_IMyService" behaviorConfiguration="IMyService_Behavior" contract="UserServices.IUserServices" name="WSHttpBinding_IMyService"> <identity> <certificate encodedValue="Some RSA stuff"/> </identity> </endpoint> </client> <behaviors> <endpointBehaviors> <behavior name="IMyService_Behavior"> <clientCredentials> <clientCertificate storeLocation="CurrentUser" storeName="My" x509FindType="FindBySubjectName" findValue="tmp123"/> </clientCredentials> </behavior> </endpointBehaviors> </behaviors> </system.serviceModel> Can anyone please help provide some insight as to what might be up here? Thanks,

    Read the article

  • Cannot use WCF service from windows mobile 5: no endpoint found.

    - by sweeney
    Hi All, I'm trying to figure out how to call a WCF service from a windows smart phone. I have a very simple smartphone console app, which does nothing but launch and make 1 call to the service. The service simply returns a string. I am able to instantiate the proxy class but when i call the method it throws an exception: There was no endpoint listening at http://mypcname/Service1.svc/basic that could accept the message. This is often caused by an incorrect address or SOAP action. See InnerException, if present, for more details. The inner exception: Could not establish connection to network. I've tried to follow this tutorial on setting up services with windows mobile. I've used the NetCFSvcUtil to create the proxy classes. I have the service running on IIS on my machine and had the Util consume the wsdl from that location. I've created a basic http binding as suggested in the article and i think i've pointed the proxy at the correct uri. Here some sections of relevant code in case it's helpful to see. If anyone has any suggestions, i'd really appreciate it. I'm not sure what else i can poke at to get this thing to work. Thanks! Client, (Program.cs): using System; using System.Linq; using System.Collections.Generic; using System.Text; namespace WcfPoC { class Program { static void Main(string[] args) { try { Service1Client proxy = new Service1Client(); string test = proxy.GetData(5); } catch (Exception e) { Console.WriteLine(e.Message); Console.WriteLine(e.InnerException.Message); Console.WriteLine(e.StackTrace); } } } } Client Proxy excerpt (Service1.cs): [System.Diagnostics.DebuggerStepThroughAttribute()] [System.CodeDom.Compiler.GeneratedCodeAttribute("System.ServiceModel", "3.0.0.0")] public partial class Service1Client : Microsoft.Tools.ServiceModel.CFClientBase<IService1>, IService1 { //modified according to the walk thru linked above... public static System.ServiceModel.EndpointAddress EndpointAddress = new System.ServiceModel.EndpointAddress("http://boston7/Service1.svc/basic"); /* *a bunch of code create by the svc util - left unmodified */ } The Service (Service1.svc.cs): using System; using System.Collections.Generic; using System.Linq; using System.Runtime.Serialization; using System.ServiceModel; using System.Text; namespace WcfService1 { // NOTE: If you change the class name "Service1" here, you must also update the reference to "Service1" in Web.config and in the associated .svc file. public class Service1 : IService1 { public string GetData(int value) //i'm calling this one... { return string.Format("You entered: {0}", value); } public CompositeType GetDataUsingDataContract(CompositeType composite) { if (composite.BoolValue) { composite.StringValue += "Suffix"; } return composite; } } } Service Interface (IService1.cs): using System; using System.Collections.Generic; using System.Linq; using System.Runtime.Serialization; using System.ServiceModel; using System.Text; namespace WcfService1 { // NOTE: If you change the interface name "IService1" here, you must also update the reference to "IService1" in Web.config. [ServiceContract] public interface IService1 { [OperationContract] string GetData(int value); //this is the call im using... [OperationContract] CompositeType GetDataUsingDataContract(CompositeType composite); // TODO: Add your service operations here } // Use a data contract as illustrated in the sample below to add composite types to service operations. [DataContract] public class CompositeType { /* * ommitted - not using this type anyway... */ } } Web.config excerpt: <services> <service name="WcfService1.Service1" behaviorConfiguration="WcfService1.Service1Behavior"> <!-- Service Endpoints --> <endpoint address="" binding="basicHttpBinding" contract="WcfService1.IService1"/> <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange"/> <host> <baseAddresses> <add baseAddress="http://boston7/" /> </baseAddresses> </host> </service> </services>

    Read the article

  • When adding WCF service reference, configuration details are not added to web.config

    - by Mikey Cee
    Hi, I am trying to add a WCF service reference to my web application using VS2010. It seems to add OK, but the web.config is not updated, meaning I get a runtime exception: Could not find default endpoint element that references contract 'CoolService.CoolService' in the ServiceModel client configuration section. This might be because no configuration file was found for your application, or because no endpoint element matching this contract could be found in the client element. Obviously, because the service is not defined in my web.config. Steps to reproduce: Right click solution Add New Project ASP.NET Empty Web Application. Right click Service References in the new web app Add Service Reference. Enter address of my service and click Go. My service is visible in the left-hand Services section, and I can see all its operations. Type a namespace for my service. Click OK. The service reference is generated correctly, and I can open the Reference.cs file, and it all looks OK. Open the web.config file. It is still empty! <system.web> <compilation debug="true" targetFramework="4.0" /> </system.web> <system.serviceModel> <bindings /> <client /> </system.serviceModel> Why is this happening? It also happens with a console application, or any other project type I try. Any help? Here is the app.config from my WCF service: <?xml version="1.0"?> <configuration> <system.web> <compilation debug="true" /> </system.web> <!-- When deploying the service library project, the content of the config file must be added to the host's app.config file. System.Configuration does not support config files for libraries. --> <system.serviceModel> <services> <service name="CoolSQL.Server.WCF.CoolService"> <endpoint address="" binding="webHttpBinding" contract="CoolSQL.Server.WCF.CoolService" behaviorConfiguration="SilverlightFaultBehavior"> <identity> <dns value="localhost" /> </identity> </endpoint> <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange" /> <host> <baseAddresses> <add baseAddress="http://localhost:8732/Design_Time_Addresses/CoolSQL.Server.WCF/CoolService/" /> </baseAddresses> </host> </service> </services> <behaviors> <endpointBehaviors> <behavior name="webBehavior"> <webHttp /> </behavior> <behavior name="SilverlightFaultBehavior"> <silverlightFaults /> </behavior> </endpointBehaviors> <serviceBehaviors> <behavior name=""> <serviceMetadata httpGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="true" /> </behavior> </serviceBehaviors> </behaviors> <bindings> <webHttpBinding> <binding name="DefaultBinding" bypassProxyOnLocal="true" useDefaultWebProxy="false" hostNameComparisonMode="WeakWildcard" sendTimeout="00:05:00" openTimeout="00:05:00" receiveTimeout="00:00:10" maxReceivedMessageSize="2147483647" transferMode="Streamed"> <readerQuotas maxArrayLength="2147483647" maxStringContentLength="2147483647" /> </binding> </webHttpBinding> </bindings> <extensions> <behaviorExtensions> <add name="silverlightFaults" type="CoolSQL.Server.WCF.SilverlightFaultBehavior, CoolSQL.Server.WCF" /> </behaviorExtensions> </extensions> <diagnostics> <messageLogging logEntireMessage="true" logMalformedMessages="false" logMessagesAtServiceLevel="true" logMessagesAtTransportLevel="false" maxMessagesToLog="3000" maxSizeOfMessageToLog="2000" /> </diagnostics> </system.serviceModel> <startup> <supportedRuntime version="v4.0" sku=".NETFramework,Version=v4.0" /> </startup> <system.diagnostics> <sources> <source name="System.ServiceModel.MessageLogging" switchValue="Information, ActivityTracing"> <listeners> <add name="messages" type="System.Diagnostics.XmlWriterTraceListener" initializeData="c:\messages.e2e" /> </listeners> </source> </sources> </system.diagnostics> </configuration>

    Read the article

  • Maven assembly - Error reading assemblies

    - by Laurent
    Dear all, I have defined a personalized jar-with-dependencies assembly descriptor. However, when I execute it with mvn assembly:assembly, I get : ... [INFO] META-INF/ already added, skipping [INFO] META-INF/MANIFEST.MF already added, skipping [INFO] javax/ already added, skipping [INFO] META-INF/ already added, skipping [INFO] META-INF/MANIFEST.MF already added, skipping [INFO] META-INF/maven/ already added, skipping [INFO] [assembly:assembly {execution: default-cli}] [INFO] ------------------------------------------------------------------------ [ERROR] BUILD ERROR [INFO] ------------------------------------------------------------------------ [INFO] Error reading assemblies: No assembly descriptors found. My jar-with-dependencies.xml is in src/main/resources/assemblies/. My assembly descriptor is the following : <?xml version='1.0' encoding='UTF-8'?> <assembly> <id>jar-with-dependencies</id> <formats> <format>jar</format> </formats> <dependencySets> <dependencySet> <scope>runtime</scope> <unpack>true</unpack> <unpackOptions> <excludes> <exclude>**/LICENSE*</exclude> <exclude>**/README*</exclude> </excludes> </unpackOptions> </dependencySet> </dependencySets> <fileSets> <fileSet> <directory>${project.build.outputDirectory}</directory> <outputDirectory>/</outputDirectory> </fileSet> <fileSet> <directory>src/main/resources/META-INF/services</directory> <outputDirectory>META-INF/services</outputDirectory> </fileSet> </fileSets> </assembly> And my project pom.xml is : <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-assembly-plugin</artifactId> <version>2.2-beta-5</version> <executions> <execution> <id>jar-with-dependencies</id> <phase>package</phase> <goals> <goal>single</goal> </goals> <configuration> <descriptors> <descriptor>jar-with-dependencies.xml</descriptor> </descriptors> <archive> <manifest> <mainClass>org.my.app.HowTo</mainClass> </manifest> </archive> </configuration> </execution> </executions> </plugin> When mvn assembly:assembly is performed, dependencies are unpacked and I get the previous error when unpack has finished. Moreover, if I execute mvn -e assembly:assembly it is say that no descriptors has been found, however it try to unpack dependencies and a JAR with dependencies is created but it doesn't contain META-INF/services/* as specified in descriptor : [ERROR] BUILD ERROR [INFO] ------------------------------------------------------------------------ [INFO] Error reading assemblies: No assembly descriptors found. [INFO] ------------------------------------------------------------------------ [INFO] Trace org.apache.maven.lifecycle.LifecycleExecutionException: Error reading assemblies: No assembly descriptors found. at org.apache.maven.lifecycle.DefaultLifecycleExecutor.executeGoals(DefaultLifecycleExecutor.java:719) at org.apache.maven.lifecycle.DefaultLifecycleExecutor.executeStandaloneGoal(DefaultLifecycleExecutor.java:569) at org.apache.maven.lifecycle.DefaultLifecycleExecutor.executeGoal(DefaultLifecycleExecutor.java:539) at org.apache.maven.lifecycle.DefaultLifecycleExecutor.executeGoalAndHandleFailures(DefaultLifecycleExecutor.java:387) at org.apache.maven.lifecycle.DefaultLifecycleExecutor.executeTaskSegments(DefaultLifecycleExecutor.java:284) at org.apache.maven.lifecycle.DefaultLifecycleExecutor.execute(DefaultLifecycleExecutor.java:180) at org.apache.maven.DefaultMaven.doExecute(DefaultMaven.java:328) at org.apache.maven.DefaultMaven.execute(DefaultMaven.java:138) at org.apache.maven.cli.MavenCli.main(MavenCli.java:362) at org.apache.maven.cli.compat.CompatibleMain.main(CompatibleMain.java:60) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.codehaus.classworlds.Launcher.launchEnhanced(Launcher.java:315) at org.codehaus.classworlds.Launcher.launch(Launcher.java:255) at org.codehaus.classworlds.Launcher.mainWithExitCode(Launcher.java:430) at org.codehaus.classworlds.Launcher.main(Launcher.java:375) Caused by: org.apache.maven.plugin.MojoExecutionException: Error reading assemblies: No assembly descriptors found. at org.apache.maven.plugin.assembly.mojos.AbstractAssemblyMojo.execute(AbstractAssemblyMojo.java:356) at org.apache.maven.plugin.DefaultPluginManager.executeMojo(DefaultPluginManager.java:490) at org.apache.maven.lifecycle.DefaultLifecycleExecutor.executeGoals(DefaultLifecycleExecutor.java:694) ... 17 more Caused by: org.apache.maven.plugin.assembly.io.AssemblyReadException: No assembly descriptors found. at org.apache.maven.plugin.assembly.io.DefaultAssemblyReader.readAssemblies(DefaultAssemblyReader.java:206) at org.apache.maven.plugin.assembly.mojos.AbstractAssemblyMojo.execute(AbstractAssemblyMojo.java:352) ... 19 more I don't see my error. Does someone has a solution ? Kind Regards Laurent

    Read the article

  • Linking LLVM JIT Code to Static LLVM Libraries?

    - by inflector
    I'm in the process of implementing a cross-platform (Mac OS X, Windows, and Linux) application which will do lots of CPU intensive analysis of financial data. The bulk of the analysis engine will be written in C++ for speed reasons, with a user-accessible scripting engine interfacing with the C++ testing engine. I want to write several scripting front-ends over time to emulate other popular software with existing large user bases. The first front will be a VisualBasic-like scripting language. I'm thinking that LLVM would be perfect for my needs. Performance is very important because of the sheer amount of data; it can take hours or days to run a single run of tests to get an answer. I believe that using LLVM will also allow me to use a single back-end solution while I implement different front-ends for different flavors of the scripting language over time. The testing engine itself will be separated from the interface and testing will even take place in a separate process with progress and results being reported to the testing management interface. Tests will consist of scripting code integrated with the testing engine code. In a previous implementation of a similar commercial testing system I wrote, I built a fast interpreter which easily interfaced with the testing library because it was written in C++ and linked directly to the testing engine library. Callbacks from scripting code to testing library objects involved translating between the formats with significant overhead. I'm imagining that with LLVM, I could implement the callbacks into C++ directly so that I could make the scripting code work almost as if it had been written in C++. Likewise, if all the code was compiled to LLVM byte-code format, it seems like the LLVM optimizers could optimize across the boundaries between the scripting language and the testing engine code that was written in C++. I don't want to have to compile the testing engine every time. Ideally, I'd like to JIT compile only the scripting code. For small tests, I'd skip some optimization passes, while for large tests, I'd perform full optimizations during the link. So is this possible? Can I precompile the testing engine to a .o object file or .a library file and then link in the scripting code using the JIT? Finally, ideally, I'd like to have the scripting code implement specific methods as subclasses for a specific C++ class. So the C++ testing engine would only see C++ objects while the JIT setup code compiled scripting code that implemented some of the methods for the objects. It seems that if I used the right name mangling algorithm it would be relatively easy to set up the LLVM generation for the scripting language to look like a C++ method call which could then be linked into the testing engine. Thus the linking stage would go in two directions, calls from the scripting language into the testing engine objects to retrieve pricing information and test state information and calls from the testing engine of methods of some particular C++ objects where the code was supplied not from C++ but from the scripting language. In summary: 1) Can I link in precompiled (either .bc, .o, or .a) files as part of the JIT compilation, code-generation process? 2) Can I link in code using that the process in 1) above in such a way that I am able to create code that acts as if it was all written in C++?

    Read the article

  • Does anyone have database, programming language/framework suggestions for a GUI point of sale system

    - by Jason Down
    Our company has a point of sale system with many extras, such as ordering and receiving functionality, sales and order history etc. Our main issue is that the system was not designed properly from the ground up, so it takes too long to make fixes and handle requests from our customers. Also, the current technology we are using (Progress database, Progress 4GL for the language) incurs quite a bit of licensing expenses on our customers due to mutli-user license fees for database connections etc. After a lot of discussion it is looking like we will probably start over from scratch (while maintaining the current product at least for the time being). We are looking for a couple of things: Create the system with a nice GUI front end (it is currently CHUI and the application was not built in a way that allows us to redesign the front end... no layering or separation of business logic and gui...shudder). Create the system with the ability to modularize different functionality so the product doesn't have to include all features. This would keep the cost down for our current customers that want basic functionality and a lower price tag. The bells and whistles would be available for those that would want them. Use proper design patterns to make the product easy to add or change any part at any time (i.e. change the database or change the front end without needing to rewrite the application or most of it). This is a problem today because the Progress 4GL code is directly compiled against the database. Small changes in the database requires lots of code recompiling. Our new system will be Linux based, with a possibility of a client application providing functionality from one or more windows boxes. So what I'm looking for is any suggestions on which database and/or framework or programming language(s) someone might recommend for this sort of product. Anyone that has experience in this field might be able to point us in the right direction or even have some ideas of what to avoid. We have considered .NET and SQL Express (we don't need an enterprise level DB), but that would limit us to windows (as far as I know anyway). I have heard of Mono for writing .NET code in a Linux environment, but I don't know much about it yet. We've also considered a Java and MySql based implementation. To summarize we are looking to do the following: Keep licensing costs down on the technology we will use to develop the product (Oracle, yikes! MySQL, nice.) Deliver a solution that is easily maintainable and supportable. A solution that has a component capable of running on "old" hardware through a CHUI front end. (some of our customers have 40+ terminals which would be a ton of cash in order to convert over to a PC). Suggestions would be appreciated. Thanks [UPDATE] I should note that we are currently performing a total cost analysis. This question is intended to give us a couple of "educated" options to look into to include in or analysis. Anyone who could share experiences/suggestions about client/server setups would be appreciated (not just those who have experience with point of sale systems... that would just be a bonus).

    Read the article

  • Scope quandary with namespaces, function templates, and static data

    - by Adrian McCarthy
    This scoping problem seems like the type of C++ quandary that Scott Meyers would have addressed in one of his Effective C++ books. I have a function, Analyze, that does some analysis on a range of data. The function is called from a few places with different types of iterators, so I have made it a template (and thus implemented it in a header file). The function depends on a static table of data, AnalysisTable, that I don't want to expose to the rest of the code. My first approach was to make the table a static const inside Analysis. namespace MyNamespace { template <typename InputIterator> int Analyze(InputIterator begin, InputIterator end) { static const int AnalysisTable[] = { /* data */ }; ... // implementation uses AnalysisTable return result; } } // namespace MyNamespace It appears that the compiler creates a copy of AnalysisTable for each instantiation of Analyze, which is wasteful of space (and, to a small degree, time). So I moved the table outside the function like this: namespace MyNamespace { const int AnalysisTable[] = { /* data */ }; template <typename InputIterator> int Analyze(InputIterator begin, InputIterator end) { ... // implementation uses AnalysisTable return result; } } // namespace MyNamespace There's only one copy of the table now, but it's exposed to the rest of the code. I'd rather keep this implementation detail hidden, so I introduced an unnamed namespace: namespace MyNamespace { namespace { // unnamed to hide AnalysisTable const int AnalysisTable[] = { /* data */ }; } // unnamed namespace template <typename InputIterator> int Analyze(InputIterator begin, InputIterator end) { ... // implementation uses AnalysisTable return result; } } // namespace MyNamespace But now I again have multiple copies of the table, because each compilation unit that includes this header file gets its own. If Analyze weren't a template, I could move all the implementation detail out of the header file. But it is a template, so I seem stuck. My next attempt was to put the table in the implementation file and to make an extern declaration within Analyze. // foo.h ------ namespace MyNamespace { template <typename InputIterator> int Analyze(InputIterator begin, InputIterator end) { extern const int AnalysisTable[]; ... // implementation uses AnalysisTable return result; } } // namespace MyNamespace // foo.cpp ------ #include "foo.h" namespace MyNamespace { const int AnalysisTable[] = { /* data */ }; } This looks like it should work, and--indeed--the compiler is satisfied. The linker, however, complains, "unresolved external symbol AnalysisTable." Drat! (Can someone explain what I'm missing here?) The only thing I could think of was to give the inner namespace a name, declare the table in the header, and provide the actual data in an implementation file: // foo.h ----- namespace MyNamespace { namespace PrivateStuff { extern const int AnalysisTable[]; } // unnamed namespace template <typename InputIterator> int Analyze(InputIterator begin, InputIterator end) { ... // implementation uses PrivateStuff::AnalysisTable return result; } } // namespace MyNamespace // foo.cpp ----- #include "foo.h" namespace MyNamespace { namespace PrivateStuff { const int AnalysisTable[] = { /* data */ }; } } Once again, I have exactly one instance of AnalysisTable (yay!), but other parts of the program can access it (boo!). The inner namespace makes it a little clearer that they shouldn't, but it's still possible. Is it possible to have one instance of the table and to move the table beyond the reach of everything but Analyze?

    Read the article

  • maven sonar problem

    - by senzacionale
    I want to use sonar for analysis but i can't get any data in localhost:9000 <?xml version="1.0" encoding="UTF-8"?> <project xmlns="http://maven.apache.org/POM/4.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://maven.apache.org/POM/4.0.0 http://maven.apache.org/maven-v4_0_0.xsd"> <modelVersion>4.0.0</modelVersion> <artifactId>KIS</artifactId> <groupId>KIS</groupId> <version>1.0</version> <build> <plugins> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-antrun-plugin</artifactId> <version>1.4</version> <executions> <execution> <id>compile</id> <phase>compile</phase> <configuration> <tasks> <property name="compile_classpath" refid="maven.compile.classpath"/> <property name="runtime_classpath" refid="maven.runtime.classpath"/> <property name="test_classpath" refid="maven.test.classpath"/> <property name="plugin_classpath" refid="maven.plugin.classpath"/> <ant antfile="${basedir}/build.xml"> <target name="maven-compile"/> </ant> </tasks> </configuration> <goals> <goal>run</goal> </goals> </execution> </executions> </plugin> </plugins> </build> </project> output when running sonar: jar file is empty [INFO] Executed tasks [INFO] [resources:testResources {execution: default-testResources}] [WARNING] Using platform encoding (Cp1250 actually) to copy filtered resources, i.e. build is platform dependent! [INFO] skip non existing resourceDirectory J:\ostalo_6i\KIS deploy\ANT\src\test\resources [INFO] [compiler:testCompile {execution: default-testCompile}] [INFO] No sources to compile [INFO] [surefire:test {execution: default-test}] [INFO] No tests to run. [INFO] [jar:jar {execution: default-jar}] [WARNING] JAR will be empty - no content was marked for inclusion! [INFO] Building jar: J:\ostalo_6i\KIS deploy\ANT\target\KIS-1.0.jar [INFO] [install:install {execution: default-install}] [INFO] Installing J:\ostalo_6i\KIS deploy\ANT\target\KIS-1.0.jar to C:\Documents and Settings\MitjaG\.m2\repository\KIS\KIS\1.0\KIS-1.0.jar [INFO] ------------------------------------------------------------------------ [INFO] Building Unnamed - KIS:KIS:jar:1.0 [INFO] task-segment: [sonar:sonar] (aggregator-style) [INFO] ------------------------------------------------------------------------ [INFO] [sonar:sonar {execution: default-cli}] [INFO] Sonar host: http://localhost:9000 [INFO] Sonar version: 2.1.2 [INFO] [sonar-core:internal {execution: default-internal}] [INFO] Database dialect class org.sonar.api.database.dialect.Oracle [INFO] ------------- Analyzing Unnamed - KIS:KIS:jar:1.0 [INFO] Selected quality profile : KIS, language=java [INFO] Configure maven plugins... [INFO] Sensor SquidSensor... [INFO] Sensor SquidSensor done: 16 ms [INFO] Sensor JavaSourceImporter... [INFO] Sensor JavaSourceImporter done: 0 ms [INFO] Sensor AsynchronousMeasuresSensor... [INFO] Sensor AsynchronousMeasuresSensor done: 15 ms [INFO] Sensor SurefireSensor... [INFO] parsing J:\ostalo_6i\KIS deploy\ANT\target\surefire-reports [INFO] Sensor SurefireSensor done: 47 ms [INFO] Sensor ProfileSensor... [INFO] Sensor ProfileSensor done: 16 ms [INFO] Sensor ProjectLinksSensor... [INFO] Sensor ProjectLinksSensor done: 0 ms [INFO] Sensor VersionEventsSensor... [INFO] Sensor VersionEventsSensor done: 31 ms [INFO] Sensor CpdSensor... [INFO] Sensor CpdSensor done: 0 ms [INFO] Sensor Maven dependencies... [INFO] Sensor Maven dependencies done: 16 ms [INFO] Execute decorators... [INFO] ANALYSIS SUCCESSFUL, you can browse http://localhost:9000 [INFO] Database optimization... [INFO] Database optimization done: 172 ms [INFO] ------------------------------------------------------------------------ [INFO] BUILD SUCCESSFUL [INFO] ------------------------------------------------------------------------ [INFO] Total time: 6 minutes 16 seconds [INFO] Finished at: Fri Jun 11 08:28:26 CEST 2010 [INFO] Final Memory: 24M/43M [INFO] ------------------------------------------------------------------------ any idea why, i successfully compile with maven ant plugin java project.

    Read the article

  • Custom binding with WCF

    - by user67240
    I have a wcf service where i have to implement the call backs and also i need to host the wcf service on the IIS 6.0, since IIS6.0 doesnot support the net.tcp binding, i decided to go for the custom binding. The reasons for going for custom binding is that the service is accessed by different clients in different timezones. Using custom binding i can set the allowed clock skew time to other values other than the default one. I have problem making the custom binding work for me. here is the server config file <bindings> <customBinding> <binding name="pscNetBinding" openTimeout="00:10:00"> <reliableSession acknowledgementInterval="00:00:00.2000000" flowControlEnabled="true" inactivityTimeout="23:59:59" maxPendingChannels="128" maxRetryCount="8" maxTransferWindowSize="128" ordered="true" /> <compositeDuplex /> <oneWay maxAcceptedChannels="128" packetRoutable="false"> <channelPoolSettings idleTimeout="00:10:00" leaseTimeout="00:10:00" maxOutboundChannelsPerEndpoint="10" /> </oneWay> <textMessageEncoding maxReadPoolSize="64" maxWritePoolSize="16" messageVersion="Default" writeEncoding="utf-8"> <readerQuotas maxDepth="2147483647" maxStringContentLength="2147483647" maxArrayLength="2147483647" maxBytesPerRead="2147483647" maxNameTableCharCount="2147483647" /> </textMessageEncoding> <httpTransport manualAddressing="false" maxBufferPoolSize="2147483647" maxReceivedMessageSize="2147483647" allowCookies="false" authenticationScheme="Anonymous" bypassProxyOnLocal="false" hostNameComparisonMode="StrongWildcard" keepAliveEnabled="true" maxBufferSize="2147483647" proxyAuthenticationScheme="Anonymous" realm="" transferMode="Buffered" unsafeConnectionNtlmAuthentication="false" useDefaultWebProxy="true"/> </binding> </customBinding> </bindings> <services> <service name="SchneiderElectric.PSCNet.Server.Services.PSCNetWCFService" behaviorConfiguration="Behaviors1"> <host> <baseAddresses> <add baseAddress ="http://10.155.18.18:2000/PSCNet"/> </baseAddresses> </host> <endpoint address="" binding="customBinding" bindingConfiguration="pscNetBinding" contract="SchneiderElectric.PSCNet.Server.Contracts.IPSCNetWCFService"/> </service> </services> <behaviors> <serviceBehaviors> <behavior name="Behaviors1"> <serviceMetadata httpGetEnabled = "true"/> <!--<serviceThrottling maxConcurrentCalls="2048" maxConcurrentSessions="2048" maxConcurrentInstances="2048" /> <dataContractSerializer maxItemsInObjectGraph="2147483647" />--> </behavior> </serviceBehaviors> </behaviors> and here the client config file <bindings> <customBinding> <binding name="pscNetBinding" openTimeout="00:10:00"> <reliableSession acknowledgementInterval="00:00:00.2000000" flowControlEnabled="true" inactivityTimeout="23:59:59" maxPendingChannels="128" maxRetryCount="8" maxTransferWindowSize="128" ordered="true" /> <compositeDuplex /> <oneWay maxAcceptedChannels="128" packetRoutable="false"> <channelPoolSettings idleTimeout="00:10:00" leaseTimeout="00:10:00" maxOutboundChannelsPerEndpoint="10" /> </oneWay> <textMessageEncoding maxReadPoolSize="64" maxWritePoolSize="16" messageVersion="Default" writeEncoding="utf-8" > <readerQuotas maxDepth="2147483647" maxStringContentLength="2147483647" maxArrayLength="2147483647" maxBytesPerRead="2147483647" maxNameTableCharCount="2147483647" /> </textMessageEncoding > <httpTransport manualAddressing="false" maxBufferPoolSize="2147483647" maxReceivedMessageSize="2147483647" allowCookies="false" authenticationScheme="Anonymous" bypassProxyOnLocal="false" hostNameComparisonMode="StrongWildcard" keepAliveEnabled="true" maxBufferSize="2147483647" proxyAuthenticationScheme="Anonymous" realm="" transferMode="Buffered" unsafeConnectionNtlmAuthentication="false" useDefaultWebProxy="true" /> </binding> </customBinding> </bindings> <client> <endpoint address="http://10.155.18.18:2000/PSCNet" binding="customBinding" bindingConfiguration="pscNetBinding" contract="PSCNetWCFService.IPSCNetWCFService" name="pscNetBinding" /> </client> if i use the server and client on the same machine everything works fine. But as soon as i run the server and client on different machine i get the following error "Could not connect to http://10.155.18.198:9000/e60ba5b3-f979-4922-b9f8-c820caaa04c2. TCP error code 10060: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond 10.155.18.198:9000." Can anyone in the community help me in this regard.

    Read the article

  • Build Environment setup - Using .net, java, hudson, and ruby - Could really use a critique

    - by Jeff D
    I'm trying to figure out the best way to stitch together a fast, repeatable, unbreakable build process for the following environment. I've got a plan for how to do it, but I'd really appreciate a critique. (I'd also appreciate some sample code, but more on that later) Ecosystem - Logical: Website - asp.net MVC 2, .net 3.5, Visual Studio 2010. IIS 6, Facebook iframe application application. This website/facebook app uses a few services. An internal search api, an internal read/write api, facebook, and an IP geolocation service. More details on these below Internal search api - .net, restful, built using old school .ashx handlers. The api uses lucene, and a sql server database behind the scenes. My project won't touch the lucene code, but does potentially touch the database and the web services. internal read/write api - java, restful, running on Tomcat Facebook web services A mocking site that emulates the internal read/write api, and parts of the facebook api Hudson - Runs unit tests on checkin, and creates some installers that behave inconsistently. Ecosystem - Physical: All of these machines can talk to one another, except for Hudson. Hudson can't see any of the target machines. So code must be pulled, rather than pushed. (Security thing) 1. Web Server - Holds the website, and the read/write api. (The api itself writes to a replicated sql server environment). 2. Search Server - Houses the search api. 3. Hudson Server - Does not have permissions to push to any environment. They have to pull. 4. Lucene Server 5. Database Server Problem I've been trying to set this site up to run in a stress environment, but the number of setup steps, the amount of time it takes to update a component, the black-box nature of the current installers, and the time it takes to generate data into the test system is absolutely destroying my productivity. I tweak one setting, have to redeploy, restart in a certain order, resetup some of the settings, and rebuild test data. Errors result in headscratching, and then basically starting over. Very bad. This problem is complicated further by my stress testing. I need to be able to turn on and off different external components, so that I can effectively determine the scalability of each piece. I've got strategies in place for how to do that for each dependency, but it further complicates my setup strategy, because now each component has 2 options. A mock version, or a real version. Configurations everywhere must be updated accordingly. Goals Fast - I want to drop this from a 20 minute exercise when things go perfectly, to a 3 minute one Stupid simple - I want to tell the environment what to do with as few commands as possible, and not have to remember how to stitch the environments together Repeatable - I want the script to be idempotent. Kind of a corollary to the Stupid Simple thing. The Plan So Far Here's what I've come up with so far, and what I've come looking for feedback on: Use VisualStudio's new web.config transformations to permit easily altering configs based on envrionment. This solution isn't really sufficient though. I will leave web.config set up to let the site run locally, but when deploying elsewhere, I have as many as 6 different possible outputs for the stress environment alone (because of the mocks of the various dependencies), let alone the settings for prod, QA, and dev. Each of these would then require it's own setup, or a setup that would then post-process the configs. So I'm currently leaning toward just having the dev version, and a version that converts key configuration values into a ruby string interpolation syntax. ({#VAR_NAME} kinda thing) Create a ruby script for each server that is essentially a bootstrapping script. That is to say, it will do nothing but load the ruby code that does the 'real' work from hudson/subversion, so that the script's functionality can evolve with the application, making it easy to build the site at any point in time by reference the appropriate version of the script. So in a nutshell, this script loads another script, and runs it. The 'real' ruby script will then accept commandline parameters that describe how the environment should look. From there, 1 configuration file can be used, and ruby will download the current installers, run them, post-process the configs, restart IIS/Tomcat, and kick off any data setup code that is needed. So that's it. I'm in a real time crunch to get this site stress-tested, so any feedback that you think could abbreviate the time this might take would be appreciated. That includes a shameless request for sample ruby code. I've not gotten too much further than puts "Hello World". :-) Just guidance would be helpful. Is this something that Rake would be useful for? How would you recommend I write tests for this animal? (I use interfaces and automocking frameworks to mock out things like http requests in .net. With ducktyping, it seems that this might be easier, but I don't know how to tell my code to use a fake duck in test, but a real one in practice) Thanks all. Sorry for such such a long-winded, open-ended question.

    Read the article

  • Service injection into Controller (Spring MVC)

    - by ThaSaleni
    Hi I have a Spring web application, I have built it up to the controller stage and I could inject my Daos, into my Services fine. Now when I want to inject my Service into my controller i get an error for dependency with the Dao and further down the sessionFactory. I don't want to inject these again cause this will ultimately lead me to eventually create a data source but I have my Daos for data access and they already know about sessionFactory. Am I missing something here? here's the sample code snippets My Service: @Service("productService") @Transactional public class ProductServiceImpl implements ProductService { private ProductDao productDao; @Autowired public void setDao(ProductDao productDao) { this.productDao = productDao; } My Controller @Controller @WebServlet(name="controllerServlet", loadOnStartup= urlPatterns=...}) public class ControllerServlet extends HttpServlet { boolean isUserLogedIn =false; @Autowired private ProductService productService; public void setProductService(ProductService productService){ this.productService = productService; } Servlet-context Stack trace javax.servlet.ServletException: Servlet.init() for servlet mvcServlet threw exception org.apache.catalina.authenticator.AuthenticatorBase.invoke(AuthenticatorBase.java:472) org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:98) org.apache.catalina.valves.AccessLogValve.invoke(AccessLogValve.java:927) org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:407) org.apache.coyote.http11.AbstractHttp11Processor.process(AbstractHttp11Processor.java:999) org.apache.coyote.AbstractProtocol$AbstractConnectionHandler.process(AbstractProtocol.java: 565) org.apache.tomcat.util.net.AprEndpoint$SocketProcessor.run(AprEndpoint.java:1812) java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) java.lang.Thread.run(Thread.java:662) root cause org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'controllerServlet': Injection of autowired dependencies failed; nested exception is org.springframework.beans.factory.BeanCreationException: Could not autowire field: private com.phumzile.acme.services.ProductService com.phumzile.acme.client.web.controller.ControllerServlet.productService; nested exception is org.springframework.beans.factory.NoSuchBeanDefinitionException: No matching bean of type [com.phumzile.acme.services.ProductService] found for dependency: expected at least 1 bean which qualifies as autowire candidate for this dependency. Dependency annotations: {@org.springframework.beans.factory.annotation.Autowired(required=true)} org.springframework.beans.factory.annotation.AutowiredAnnotationBeanPostProcessor.p ostProcessPropertyValues(AutowiredAnnotationBeanPostProcessor.java:287) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.populateBean(AbstractAutowireCapableBeanFactory.java:1106) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.doCreateBean(AbstractAutowireCapableBeanFactory.java:517) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:456) org.springframework.beans.factory.support.AbstractBeanFactory$1.getObject(AbstractBeanFactory.java:294) org.springframework.beans.factory.support.DefaultSingletonBeanRegistry.getSingleton(DefaultSingletonBeanRegistry.java:225) SERVLET-CONTEXT <context:component-scan base-package="com.phumzile.acme.client" /> <!-- Enables the Spring MVC @Controller programming model --> <mvc:annotation-driven /> </beans> APP-CONFIG <bean id="propertyConfigurer" class="org.springframework.beans.factory.config.PropertyPlaceholderConfigurer"> <property name="locations"> <list> <value>configuration.properties</value> </list> </property> </bean> <context:annotation-config/> <context:component-scan base-package="com.phumzile.acme" /> <import resource="db-config.xml" /> </beans> DB-CONFIG <bean id="dataSource" class="com.mchange.v2.c3p0.ComboPooledDataSource" destroy-method="close"> <property name="idleConnectionTestPeriod" value="10800"/> <property name="maxIdleTime" value="21600"/> <property name="driverClass"> <value>${jdbc.driver.className}</value> </property> <property name="jdbcUrl"> <value>${jdbc.url}</value> </property> <property name="user"> <value>${jdbc.username}</value> </property> <property name="password"> <value>${jdbc.password}</value> </property> </bean> <bean id="sessionFactory" class="org.springframework.orm.hibernate3.a nnotation.AnnotationSessionFactoryBean"> <property name="dataSource"> <ref bean="dataSource" /> </property> <property name="annotatedClasses"> <list> <!-- Entities --> <value>com.phumzile.acme.model.User</value> <value>com.phumzile.acme.model.Person</value> <value>com.phumzile.acme.model.Company</value> <value>com.phumzile.acme.model.Product</value> <value>com.phumzile.acme.model.Game</value> <value>com.phumzile.acme.model.Book</value> <!-- Entities --> </list> </property> <property name="packagesToScan" value="com.phumzile.acme" /> <property name="hibernateProperties"> <props> <prop key="hibernate.dialect">${jdbc.hibernate.dialect </prop> <prop key="hibernate.hbm2ddl.auto">validate</prop> <prop key="hibernate.show_sql">true</prop> </props> </property> </bean> <bean id="transactionManager" class="org.springframework.orm.hibernate3.HibernateTransactionManager"> <property name="sessionFactory"> <ref bean="sessionFactory" /> </property> </bean> <tx:annotation-driven /> </beans> CONFIGURATION.PROPERTIES jdbc.driver.className=com.mysql.jdbc.Driver jdbc.url=jdbc:mysql://localhost:3306/mydb jdbc.username=root jdbc.password=root jdbc.hibernate.dialect=org.hibernate.dialect.MySQLDialect

    Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >