Search Results

Search found 16787 results on 672 pages for 'mod disk cache'.

Page 368/672 | < Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >

  • Why is my mdadm raid-1 recovery so slow?

    - by dimmer
    On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

    Read the article

  • Windows 2012 - WDS unattend Partition

    - by joe
    I'm trying to install Windows 2012 via Windows 2012 WDS. The installer displays the following error message: the partition selected for the installation (1) does not exist on disk 0. Make sure the unattend answer file's imageselection \installimage setting references a valid partition on this computer, and then restart the installation. the unattend file (created by the "Create Client Unattend" dialog) <unattend xmlns="urn:schemas-microsoft-com:unattend"> <settings pass="windowsPE"> <component name="Microsoft-Windows-Setup" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="x86"> <WindowsDeploymentServices> <Login> <WillShowUI>OnError</WillShowUI> <Credentials> <Username>administrator</Username> <Domain>test</Domain> <Password>xxxx</Password> </Credentials> </Login> <WillWipeDisk>true</WillWipeDisk> <DiskConfiguration> <WillShowUI>OnError</WillShowUI> <Disk> <DiskID>0</DiskID> <WillWipeDisk>true</WillWipeDisk> <CreatePartitions> <CreatePartition> <Order>1</Order> <Type>Primary</Type> <Extend>true</Extend> </CreatePartition> </CreatePartitions> </Disk> </DiskConfiguration> <ImageSelection> <WillShowUI>OnError</WillShowUI> <InstallImage> <ImageGroup>ImageGroup1</ImageGroup> <ImageName>Windows Server 2012 SERVERDATACENTER</ImageName> <Filename>install-(4).wim</Filename> </InstallImage> <InstallTo> <DiskID>0</DiskID> <PartitionID>1</PartitionID> </InstallTo> </ImageSelection> </WindowsDeploymentServices> </component> <component name="Microsoft-Windows-International-Core-WinPE" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="x86"> <SetupUILanguage> <UILanguage>en-US</UILanguage> </SetupUILanguage> <InputLocale>en-US</InputLocale> <SystemLocale>en-US</SystemLocale> <UILanguage>en-US</UILanguage> <UserLocale>en-US</UserLocale> </component> <component name="Microsoft-Windows-Setup" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="amd64"> <WindowsDeploymentServices> <Login> <WillShowUI>OnError</WillShowUI> <Credentials> <Username>administrator</Username> <Domain>test</Domain> <Password>xxxxx</Password> </Credentials> </Login> <ImageSelection> <WillShowUI>OnError</WillShowUI> <InstallImage> <ImageGroup>ImageGroup1</ImageGroup> <ImageName>Windows Server 2012 SERVERDATACENTER</ImageName> <Filename>install-(4).wim</Filename> </InstallImage> <InstallTo> <DiskID>0</DiskID> <PartitionID>1</PartitionID> </InstallTo> </ImageSelection> </WindowsDeploymentServices> </component> <component name="Microsoft-Windows-International-Core-WinPE" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="amd64"> <SetupUILanguage> <UILanguage>en-US</UILanguage> </SetupUILanguage> <InputLocale>en-US</InputLocale> <SystemLocale>en-US</SystemLocale> <UILanguage>en-US</UILanguage> <UserLocale>en-US</UserLocale> </component> </settings> </unattend> Any idea why it is not working? thanks

    Read the article

  • Deserializing Metafile

    - by Kildareflare
    I have an application that works with Enhanced Metafiles. I am able to create them, save them to disk as .emf and load them again no problem. I do this by using the gdi32.dll methods and the DLLImport attribute. However, to enable Version Tolerant Serialization I want to save the metafile in an object along with other data. This essentially means that I need to serialize the metafile data as a byte array and then deserialize it again in order to reconstruct the metafile. The problem I have is that the deserialized data would appear to be corrupted in some way, since the method that I use to reconstruct the Metafile raises a "Parameter not valid exception". At the very least the pixel format and resolutions have changed. Code use is below. [DllImport("gdi32.dll")] public static extern uint GetEnhMetaFileBits(IntPtr hemf, uint cbBuffer, byte[] lpbBuffer); [DllImport("gdi32.dll")] public static extern IntPtr SetEnhMetaFileBits(uint cbBuffer, byte[] lpBuffer); [DllImport("gdi32.dll")] public static extern bool DeleteEnhMetaFile(IntPtr hemf); The application creates a metafile image and passes it to the method below. private byte[] ConvertMetaFileToByteArray(Image image) { byte[] dataArray = null; Metafile mf = (Metafile)image; IntPtr enhMetafileHandle = mf.GetHenhmetafile(); uint bufferSize = GetEnhMetaFileBits(enhMetafileHandle, 0, null); if (enhMetafileHandle != IntPtr.Zero) { dataArray = new byte[bufferSize]; GetEnhMetaFileBits(enhMetafileHandle, bufferSize, dataArray); } DeleteEnhMetaFile(enhMetafileHandle); return dataArray; } At this point the dataArray is inserted into an object and serialized using a BinaryFormatter. The saved file is then deserialized again using a BinaryFormatter and the dataArray retrieved from the object. The dataArray is then used to reconstruct the original Metafile using the following method. public static Image ConvertByteArrayToMetafile(byte[] data) { Metafile mf = null; try { IntPtr hemf = SetEnhMetaFileBits((uint)data.Length, data); mf = new Metafile(hemf, true); } catch (Exception ex) { System.Windows.Forms.MessageBox.Show(ex.Message); } return (Image)mf; } The reconstructed metafile is then saved saved to disk as a .emf (Model) at which point it can be accessed by the Presenter for display. private static void SaveFile(Image image, String filepath) { try { byte[] buffer = ConvertMetafileToByteArray(image); File.WriteAllBytes(filepath, buffer); //will overwrite file if it exists } catch (Exception ex) { System.Windows.Forms.MessageBox.Show(ex.Message); } } The problem is that the save to disk fails. If this same method is used to save the original Metafile before it is serialized everything is OK. So something is happening to the data during serialization/deserializtion. Indeed if I check the Metafile properties in the debugger I can see that the ImageFlags, PropertyID, resolution and pixelformats change. Original Format32bppRgb changes to Format32bppArgb Original Resolution 81 changes to 96 I've trawled though google and SO and this has helped me get this far but Im now stuck. Does any one have enough experience with Metafiles / serialization to help..? EDIT: If I serialize/deserialize the byte array directly (without embedding in another object) I get the same problem.

    Read the article

  • Recommended ASP.NET Shared Hosting (USA)

    - by coffeeaddict
    Ok, I have to admit I'm getting fed up with www.discountasp.net's pricing model and this annoyance has built up over the past 8 years or so. I've been with them for years and absolutely love them on the technical side, however it's getting ridiculously expensive for so little that you get. I mean here's my scenario: 1) I am running 2 SQL Server databases which costs me $10/ea per month so that's $20/month for 2 and I only get 500 mb disk space which is horrible 2) I am paying $10/mo just for the hosting itself which I only get 1 gig of disk space! I mean common! 3) I am simply running 2 small apps (Screwturn Wiki & Subtext Blog)...so I don't really care if it's up 99% or not, it's not worth paying a total of $300 just to keep these 2 apps running over discountasp.net Anyone else feel the same? Yes, I know they have great support, probably have great servers running behind this but in the end I really don't care as long as my site is up 95% or better. Yes, the hosting toolset rocks. But you know I bet you I can find a similar set somewhere else. I like how I can totally control IIS 7 at discountasp and I can control my own app pool etc. That's very powerful and essential. But anyone have any good alternatives to discountasp that gives me close to the same at a much more reasonable cost point? I mean http://www.m6.net/prices.aspx gives you 10 SQL Databases for $7 and 200 gigs disk space! I don't know about their tools or support but just looking at those numbers and some other hosts I've seen, I feel that discountasp.net is way out of line. They don't even offer any purchasing discounts such as it would be nice if my 2nd SQL Server is only $5/month not $10...stuff like this, to make it much more realistic and fair. Opinions (people who do have discountasp.net, people who have left them, or people who have another host they like)??? But geez $300 just to host a couple DBs and lightweight open source apps? Not worth the price they are charging. I'm almost at a price point that enables me to get a decent dedicated server! I really don't care about beta ASP.NET frameworks support. Not a big deal to me. If you have alternative suggestions rather than your experience with discountasp, I'd like to know how their toolset is. Do you have complete control over your DB in terms of adding users, and same goes for the web app pool, etc.? Discountasp.net's control panel rocks. I don't want to loose the ability to at least control and add virtual directories, recycle my dedicated app pool myself, backup my sql database myself, through tools which is what discountasp does give you. I'd also want to know that the hoster at least gets the latest and greatest in terms of non-beta ASP.NET related frameworks available to its shared hosters.

    Read the article

  • Optimal storage of data structure for fast lookup and persistence

    - by Mikael Svenson
    Scenario I have the following methods: public void AddItemSecurity(int itemId, int[] userIds) public int[] GetValidItemIds(int userId) Initially I'm thinking storage on the form: itemId -> userId, userId, userId and userId -> itemId, itemId, itemId AddItemSecurity is based on how I get data from a third party API, GetValidItemIds is how I want to use it at runtime. There are potentially 2000 users and 10 million items. Item id's are on the form: 2007123456, 2010001234 (10 digits where first four represent the year). AddItemSecurity does not have to perform super fast, but GetValidIds needs to be subsecond. Also, if there is an update on an existing itemId I need to remove that itemId for users no longer in the list. I'm trying to think about how I should store this in an optimal fashion. Preferably on disk (with caching), but I want the code maintainable and clean. If the item id's had started at 0, I thought about creating a byte array the length of MaxItemId / 8 for each user, and set a true/false bit if the item was present or not. That would limit the array length to little over 1mb per user and give fast lookups as well as an easy way to update the list per user. By persisting this as Memory Mapped Files with the .Net 4 framework I think I would get decent caching as well (if the machine has enough RAM) without implementing caching logic myself. Parsing the id, stripping out the year, and store an array per year could be a solution. The ItemId - UserId[] list can be serialized directly to disk and read/write with a normal FileStream in order to persist the list and diff it when there are changes. Each time a new user is added all the lists have to updated as well, but this can be done nightly. Question Should I continue to try out this approach, or are there other paths which should be explored as well? I'm thinking SQL server will not perform fast enough, and it would give an overhead (at least if it's hosted on a different server), but my assumptions might be wrong. Any thought or insights on the matter is appreciated. And I want to try to solve it without adding too much hardware :) [Update 2010-03-31] I have now tested with SQL server 2008 under the following conditions. Table with two columns (userid,itemid) both are Int Clustered index on the two columns Added ~800.000 items for 180 users - Total of 144 million rows Allocated 4gb ram for SQL server Dual Core 2.66ghz laptop SSD disk Use a SqlDataReader to read all itemid's into a List Loop over all users If I run one thread it averages on 0.2 seconds. When I add a second thread it goes up to 0.4 seconds, which is still ok. From there on the results are decreasing. Adding a third thread brings alot of the queries up to 2 seonds. A forth thread, up to 4 seconds, a fifth spikes some of the queries up to 50 seconds. The CPU is roofing while this is going on, even on one thread. My test app takes some due to the speedy loop, and sql the rest. Which leads me to the conclusion that it won't scale very well. At least not on my tested hardware. Are there ways to optimize the database, say storing an array of int's per user instead of one record per item. But this makes it harder to remove items.

    Read the article

  • Break a class in twain, or impose an interface for restricted access?

    - by bedwyr
    What's the best way of partitioning a class when its functionality needs to be externally accessed in different ways by different classes? Hopefully the following example will make the question clear :) I have a Java class which accesses a single location in a directory allowing external classes to perform read/write operations to it. Read operations return usage stats on the directory (e.g. available disk space, number of writes, etc.); write operations, obviously, allow external classes to write data to the disk. These methods always work on the same location, and receive their configuration (e.g. which directory to use, min disk space, etc.) from an external source (passed to the constructor). This class looks something like this: public class DiskHandler { public DiskHandler(String dir, int minSpace) { ... } public void writeToDisk(String contents, String filename) { int space = getAvailableSpace(); ... } public void getAvailableSpace() { ... } } There's quite a bit more going on, but this will do to suffice. This class needs to be accessed differently by two external classes. One class needs access to the read operations; the other needs access to both read and write operations. public class DiskWriter { DiskHandler diskHandler; public DiskWriter() { diskHandler = new DiskHandler(...); } public void doSomething() { diskHandler.writeToDisk(...); } } public class DiskReader { DiskHandler diskHandler; public DiskReader() { diskHandler = new DiskHandler(...); } public void doSomething() { int space = diskHandler.getAvailableSpace(...); } } At this point, both classes share the same class, but the class which should only read has access to the write methods. Solution 1 I could break this class into two. One class would handle read operations, and the other would handle writes: // NEW "UTILITY" CLASSES public class WriterUtil { private ReaderUtil diskReader; public WriterUtil(String dir, int minSpace) { ... diskReader = new ReaderUtil(dir, minSpace); } public void writeToDisk(String contents, String filename) { int = diskReader.getAvailableSpace(); ... } } public class ReaderUtil { public ReaderUtil(String dir, int minSpace) { ... } public void getAvailableSpace() { ... } } // MODIFIED EXTERNALLY-ACCESSING CLASSES public class DiskWriter { WriterUtil diskWriter; public DiskWriter() { diskWriter = new WriterUtil(...); } public void doSomething() { diskWriter.writeToDisk(...); } } public class DiskReader { ReaderUtil diskReader; public DiskReader() { diskReader = new ReaderUtil(...); } public void doSomething() { int space = diskReader.getAvailableSpace(...); } } This solution prevents classes from having access to methods they should not, but it also breaks encapsulation. The original DiskHandler class was completely self-contained and only needed config parameters via a single constructor. By breaking apart the functionality into read/write classes, they both are concerned with the directory and both need to be instantiated with their respective values. In essence, I don't really care to duplicate the concerns. Solution 2 I could implement an interface which only provisions read operations, and use this when a class only needs access to those methods. The interface might look something like this: public interface Readable { int getAvailableSpace(); } The Reader class would instantiate the object like this: Readable diskReader; public DiskReader() { diskReader = new DiskHandler(...); } This solution seems brittle, and prone to confusion in the future. It doesn't guarantee developers will use the correct interface in the future. Any changes to the implementation of the DiskHandler could also need to update the interface as well as the accessing classes. I like it better than the previous solution, but not by much. Frankly, neither of these solutions seems perfect, but I'm not sure if one should be preferred over the other. I really don't want to break the original class up, but I also don't know if the interface buys me much in the long run. Are there other solutions I'm missing?

    Read the article

  • NPOI set cell style "HSSFFont.BOLDWEIGHT_BOLD" is not working

    - by vandana sharma
    I'm using NPOI to output excel from Asp.Net. I want to set bold and normal style to my cell but it is working for few cell and not for remaining cell.Please have look on following example: Dim hssfworkbook As New HSSFWorkbook() Dim sheetOne As HSSFSheet = hssfworkbook.CreateSheet("Sheet1") hssfworkbook.CreateSheet("Sheet2") hssfworkbook.CreateSheet("Sheet3") Dim cellStyle As HSSFCellStyle = hssfworkbook.CreateCellStyle cellStyle.Alignment = HSSFCellStyle.ALIGN_CENTER Dim font As HSSFFont = _hssfworkbook.CreateFont() font.Boldweight = HSSFFont.BOLDWEIGHT_BOLD cellStyle.SetFont(font) For i = 0 To 9 Step 1 'I want to add cell style to these cells If i Mod 2 = 0 Then Sheet1.CreateRow(i).CreateCell(1).SetCellValue(i) font.Boldweight = HSSFFont.BOLDWEIGHT_BOLD cellStyle.SetFont(font) Sheet1.GetRow(i).GetCell(1).CellStyle = cellStyle Else Sheet1.CreateRow(i).CreateCell(1).SetCellValue(i) font.Boldweight = HSSFFont.BOLDWEIGHT_NORMAL cellStyle.SetFont(font) Sheet1.GetRow(i).GetCell(1).CellStyle = cellStyle End If Next Actually code is working fine but i don't know the particular situation from where and why its stops working for remaining few rows. Its not working properly for all cells and from that particular cell the bold and normal property stops working on whole sheet like sheet2 and sheet3.

    Read the article

  • SQL SERVER – Shrinking NDF and MDF Files – Readers’ Opinion

    - by pinaldave
    Previously, I had written a blog post about SQL SERVER – Shrinking NDF and MDF Files – A Safe Operation. After that, I have written the following blog post that talks about the advantage and disadvantage of Shrinking and why one should not be Shrinking a file SQL SERVER – SHRINKFILE and TRUNCATE Log File in SQL Server 2008. On this subject, SQL Server Expert Imran Mohammed left an excellent comment. I just feel that his comment is worth a big article itself. For everybody to read his wonderful explanation, I am posting this blog post here. Thanks Imran! Shrinking Database always creates performance degradation and increases fragmentation in the database. I suggest that you keep that in mind before you start reading the following comment. If you are going to say Shrinking Database is bad and evil, here I am saying it first and loud. Now, the comment of Imran is written while keeping in mind only the process showing how the Shrinking Database Operation works. Imran has already explained his understanding and requests further explanation. I have removed the Best Practices section from Imran’s comments, as there are a few corrections. Comments from Imran - Before I explain to you the concept of Shrink Database, let us understand the concept of Database Files. When we create a new database inside the SQL Server, it is typical that SQl Server creates two physical files in the Operating System: one with .MDF Extension, and another with .LDF Extension. .MDF is called as Primary Data File. .LDF is called as Transactional Log file. If you add one or more data files to a database, the physical file that will be created in the Operating System will have an extension of .NDF, which is called as Secondary Data File; whereas, when you add one or more log files to a database, the physical file that will be created in the Operating System will have the same extension as .LDF. The questions now are, “Why does a new data file have a different extension (.NDF)?”, “Why is it called as a secondary data file?” and, “Why is .MDF file called as a primary data file?” Answers: Note: The following explanation is based on my limited knowledge of SQL Server, so experts please do comment. A data file with a .MDF extension is called a Primary Data File, and the reason behind it is that it contains Database Catalogs. Catalogs mean Meta Data. Meta Data is “Data about Data”. An example for Meta Data includes system objects that store information about other objects, except the data stored by the users. sysobjects stores information about all objects in that database. sysindexes stores information about all indexes and rows of every table in that database. syscolumns stores information about all columns that each table has in that database. sysusers stores how many users that database has. Although Meta Data stores information about other objects, it is not the transactional data that a user enters; rather, it’s a system data about the data. Because Primary Data File (.MDF) contains important information about the database, it is treated as a special file. It is given the name Primary Data file because it contains the Database Catalogs. This file is present in the Primary File Group. You can always create additional objects (Tables, indexes etc.) in the Primary data file (This file is present in the Primary File group), by mentioning that you want to create this object under the Primary File Group. Any additional data file that you add to the database will have only transactional data but no Meta Data, so that’s why it is called as the Secondary Data File. It is given the extension name .NDF so that the user can easily identify whether a specific data file is a Primary Data File or a Secondary Data File(s). There are many advantages of storing data in different files that are under different file groups. You can put your read only in the tables in one file (file group) and read-write tables in another file (file group) and take a backup of only the file group that has read the write data, so that you can avoid taking the backup of a read-only data that cannot be altered. Creating additional files in different physical hard disks also improves I/O performance. A real-time scenario where we use Files could be this one: Let’s say you have created a database called MYDB in the D-Drive which has a 50 GB space. You also have 1 Database File (.MDF) and 1 Log File on D-Drive and suppose that all of that 50 GB space has been used up and you do not have any free space left but you still want to add an additional space to the database. One easy option would be to add one more physical hard disk to the server, add new data file to MYDB database and create this new data file in a new hard disk then move some of the objects from one file to another, and put the file group under which you added new file as default File group, so that any new object that is created gets into the new files, unless specified. Now that we got a basic idea of what data files are, what type of data they store and why they are named the way they are, let’s move on to the next topic, Shrinking. First of all, I disagree with the Microsoft terminology for naming this feature as “Shrinking”. Shrinking, in regular terms, means to reduce the size of a file by means of compressing it. BUT in SQL Server, Shrinking DOES NOT mean compressing. Shrinking in SQL Server means to remove an empty space from database files and release the empty space either to the Operating System or to SQL Server. Let’s examine this through an example. Let’s say you have a database “MYDB” with a size of 50 GB that has a free space of about 20 GB, which means 30GB in the database is filled with data and the 20 GB of space is free in the database because it is not currently utilized by the SQL Server (Database); it is reserved and not yet in use. If you choose to shrink the database and to release an empty space to Operating System, and MIND YOU, you can only shrink the database size to 30 GB (in our example). You cannot shrink the database to a size less than what is filled with data. So, if you have a database that is full and has no empty space in the data file and log file (you don’t have an extra disk space to set Auto growth option ON), YOU CANNOT issue the SHRINK Database/File command, because of two reasons: There is no empty space to be released because the Shrink command does not compress the database; it only removes the empty space from the database files and there is no empty space. Remember, the Shrink command is a logged operation. When we perform the Shrink operation, this information is logged in the log file. If there is no empty space in the log file, SQL Server cannot write to the log file and you cannot shrink a database. Now answering your questions: (1) Q: What are the USEDPAGES & ESTIMATEDPAGES that appear on the Results Pane after using the DBCC SHRINKDATABASE (NorthWind, 10) ? A: According to Books Online (For SQL Server 2000): UsedPages: the number of 8-KB pages currently used by the file. EstimatedPages: the number of 8-KB pages that SQL Server estimates the file could be shrunk down to. Important Note: Before asking any question, make sure you go through Books Online or search on the Google once. The reasons for doing so have many advantages: 1. If someone else already has had this question before, chances that it is already answered are more than 50 %. 2. This reduces your waiting time for the answer. (2) Q: What is the difference between Shrinking the Database using DBCC command like the one above & shrinking it from the Enterprise Manager Console by Right-Clicking the database, going to TASKS & then selecting SHRINK Option, on a SQL Server 2000 environment? A: As far as my knowledge goes, there is no difference, both will work the same way, one advantage of using this command from query analyzer is, your console won’t be freezed. You can do perform your regular activities using Enterprise Manager. (3) Q: What is this .NDF file that is discussed above? I have never heard of it. What is it used for? Is it used by end-users, DBAs or the SERVER/SYSTEM itself? A: .NDF File is a secondary data file. You never heard of it because when database is created, SQL Server creates database by default with only 1 data file (.MDF) and 1 log file (.LDF) or however your model database has been setup, because a model database is a template used every time you create a new database using the CREATE DATABASE Command. Unless you have added an extra data file, you will not see it. This file is used by the SQL Server to store data which are saved by the users. Hope this information helps. I would like to as the experts to please comment if what I understand is not what the Microsoft guys meant. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Readers Contribution, Readers Question, SQL, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • Access violation in DirectX OMSetRenderTargets

    - by IDWMaster
    I receive the following error (Unhandled exception at 0x527DAE81 (d3d11_1sdklayers.dll) in Lesson2.Triangles.exe: 0xC0000005: Access violation reading location 0x00000000) when running the Triangle sample application for DirectX 11 in D3D_FEATURE_LEVEL_9_1. This error occurs at the OMSetRenderTargets function, as shown below, and does not happen if I remove that function from the program (but then, the screen is blue, and does not render the triangle) //// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF //// ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO //// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A //// PARTICULAR PURPOSE. //// //// Copyright (c) Microsoft Corporation. All rights reserved #include #include #include "DirectXSample.h" #include "BasicMath.h" #include "BasicReaderWriter.h" using namespace Microsoft::WRL; using namespace Windows::UI::Core; using namespace Windows::Foundation; using namespace Windows::ApplicationModel::Core; using namespace Windows::ApplicationModel::Infrastructure; // This class defines the application as a whole. ref class Direct3DTutorialViewProvider : public IViewProvider { private: CoreWindow^ m_window; ComPtr m_swapChain; ComPtr m_d3dDevice; ComPtr m_d3dDeviceContext; ComPtr m_renderTargetView; public: // This method is called on application launch. void Initialize( _In_ CoreWindow^ window, _In_ CoreApplicationView^ applicationView ) { m_window = window; } // This method is called after Initialize. void Load(_In_ Platform::String^ entryPoint) { } // This method is called after Load. void Run() { // First, create the Direct3D device. // This flag is required in order to enable compatibility with Direct2D. UINT creationFlags = D3D11_CREATE_DEVICE_BGRA_SUPPORT; #if defined(_DEBUG) // If the project is in a debug build, enable debugging via SDK Layers with this flag. creationFlags |= D3D11_CREATE_DEVICE_DEBUG; #endif // This array defines the ordering of feature levels that D3D should attempt to create. D3D_FEATURE_LEVEL featureLevels[] = { D3D_FEATURE_LEVEL_11_1, D3D_FEATURE_LEVEL_11_0, D3D_FEATURE_LEVEL_10_1, D3D_FEATURE_LEVEL_10_0, D3D_FEATURE_LEVEL_9_3, D3D_FEATURE_LEVEL_9_1 }; ComPtr d3dDevice; ComPtr d3dDeviceContext; DX::ThrowIfFailed( D3D11CreateDevice( nullptr, // specify nullptr to use the default adapter D3D_DRIVER_TYPE_HARDWARE, nullptr, // leave as nullptr if hardware is used creationFlags, // optionally set debug and Direct2D compatibility flags featureLevels, ARRAYSIZE(featureLevels), D3D11_SDK_VERSION, // always set this to D3D11_SDK_VERSION &d3dDevice, nullptr, &d3dDeviceContext ) ); // Retrieve the Direct3D 11.1 interfaces. DX::ThrowIfFailed( d3dDevice.As(&m_d3dDevice) ); DX::ThrowIfFailed( d3dDeviceContext.As(&m_d3dDeviceContext) ); // After the D3D device is created, create additional application resources. CreateWindowSizeDependentResources(); // Create a Basic Reader-Writer class to load data from disk. This class is examined // in the Resource Loading sample. BasicReaderWriter^ reader = ref new BasicReaderWriter(); // Load the raw vertex shader bytecode from disk and create a vertex shader with it. auto vertexShaderBytecode = reader-ReadData("SimpleVertexShader.cso"); ComPtr vertexShader; DX::ThrowIfFailed( m_d3dDevice-CreateVertexShader( vertexShaderBytecode-Data, vertexShaderBytecode-Length, nullptr, &vertexShader ) ); // Create an input layout that matches the layout defined in the vertex shader code. // For this lesson, this is simply a float2 vector defining the vertex position. const D3D11_INPUT_ELEMENT_DESC basicVertexLayoutDesc[] = { { "POSITION", 0, DXGI_FORMAT_R32G32_FLOAT, 0, 0, D3D11_INPUT_PER_VERTEX_DATA, 0 }, }; ComPtr inputLayout; DX::ThrowIfFailed( m_d3dDevice-CreateInputLayout( basicVertexLayoutDesc, ARRAYSIZE(basicVertexLayoutDesc), vertexShaderBytecode-Data, vertexShaderBytecode-Length, &inputLayout ) ); // Load the raw pixel shader bytecode from disk and create a pixel shader with it. auto pixelShaderBytecode = reader-ReadData("SimplePixelShader.cso"); ComPtr pixelShader; DX::ThrowIfFailed( m_d3dDevice-CreatePixelShader( pixelShaderBytecode-Data, pixelShaderBytecode-Length, nullptr, &pixelShader ) ); // Create vertex and index buffers that define a simple triangle. float3 triangleVertices[] = { float3(-0.5f, -0.5f,13.5f), float3( 0.0f, 0.5f,0), float3( 0.5f, -0.5f,0), }; D3D11_BUFFER_DESC vertexBufferDesc = {0}; vertexBufferDesc.ByteWidth = sizeof(float3) * ARRAYSIZE(triangleVertices); vertexBufferDesc.Usage = D3D11_USAGE_DEFAULT; vertexBufferDesc.BindFlags = D3D11_BIND_VERTEX_BUFFER; vertexBufferDesc.CPUAccessFlags = 0; vertexBufferDesc.MiscFlags = 0; vertexBufferDesc.StructureByteStride = 0; D3D11_SUBRESOURCE_DATA vertexBufferData; vertexBufferData.pSysMem = triangleVertices; vertexBufferData.SysMemPitch = 0; vertexBufferData.SysMemSlicePitch = 0; ComPtr vertexBuffer; DX::ThrowIfFailed( m_d3dDevice-CreateBuffer( &vertexBufferDesc, &vertexBufferData, &vertexBuffer ) ); // Once all D3D resources are created, configure the application window. // Allow the application to respond when the window size changes. m_window-SizeChanged += ref new TypedEventHandler( this, &Direct3DTutorialViewProvider::OnWindowSizeChanged ); // Specify the cursor type as the standard arrow cursor. m_window-PointerCursor = ref new CoreCursor(CoreCursorType::Arrow, 0); // Activate the application window, making it visible and enabling it to receive events. m_window-Activate(); // Enter the render loop. Note that tailored applications should never exit. while (true) { // Process events incoming to the window. m_window-Dispatcher-ProcessEvents(CoreProcessEventsOption::ProcessAllIfPresent); // Specify the render target we created as the output target. ID3D11RenderTargetView* targets[1] = {m_renderTargetView.Get()}; m_d3dDeviceContext-OMSetRenderTargets( 1, targets, NULL // use no depth stencil ); // Clear the render target to a solid color. const float clearColor[4] = { 0.071f, 0.04f, 0.561f, 1.0f }; //Code fails here m_d3dDeviceContext-ClearRenderTargetView( m_renderTargetView.Get(), clearColor ); m_d3dDeviceContext-IASetInputLayout(inputLayout.Get()); // Set the vertex and index buffers, and specify the way they define geometry. UINT stride = sizeof(float3); UINT offset = 0; m_d3dDeviceContext-IASetVertexBuffers( 0, 1, vertexBuffer.GetAddressOf(), &stride, &offset ); m_d3dDeviceContext-IASetPrimitiveTopology(D3D11_PRIMITIVE_TOPOLOGY_TRIANGLELIST); // Set the vertex and pixel shader stage state. m_d3dDeviceContext-VSSetShader( vertexShader.Get(), nullptr, 0 ); m_d3dDeviceContext-PSSetShader( pixelShader.Get(), nullptr, 0 ); // Draw the cube. m_d3dDeviceContext-Draw(3,0); // Present the rendered image to the window. Because the maximum frame latency is set to 1, // the render loop will generally be throttled to the screen refresh rate, typically around // 60Hz, by sleeping the application on Present until the screen is refreshed. DX::ThrowIfFailed( m_swapChain-Present(1, 0) ); } } // This method is called before the application exits. void Uninitialize() { } private: // This method is called whenever the application window size changes. void OnWindowSizeChanged( _In_ CoreWindow^ sender, _In_ WindowSizeChangedEventArgs^ args ) { m_renderTargetView = nullptr; CreateWindowSizeDependentResources(); } // This method creates all application resources that depend on // the application window size. It is called at app initialization, // and whenever the application window size changes. void CreateWindowSizeDependentResources() { if (m_swapChain != nullptr) { // If the swap chain already exists, resize it. DX::ThrowIfFailed( m_swapChain-ResizeBuffers( 2, 0, 0, DXGI_FORMAT_R8G8B8A8_UNORM, 0 ) ); } else { // If the swap chain does not exist, create it. DXGI_SWAP_CHAIN_DESC1 swapChainDesc = {0}; swapChainDesc.Stereo = false; swapChainDesc.BufferUsage = DXGI_USAGE_RENDER_TARGET_OUTPUT; swapChainDesc.Scaling = DXGI_SCALING_NONE; swapChainDesc.Flags = 0; // Use automatic sizing. swapChainDesc.Width = 0; swapChainDesc.Height = 0; // This is the most common swap chain format. swapChainDesc.Format = DXGI_FORMAT_R8G8B8A8_UNORM; // Don't use multi-sampling. swapChainDesc.SampleDesc.Count = 1; swapChainDesc.SampleDesc.Quality = 0; // Use two buffers to enable flip effect. swapChainDesc.BufferCount = 2; // We recommend using this swap effect for all applications. swapChainDesc.SwapEffect = DXGI_SWAP_EFFECT_FLIP_SEQUENTIAL; // Once the swap chain description is configured, it must be // created on the same adapter as the existing D3D Device. // First, retrieve the underlying DXGI Device from the D3D Device. ComPtr dxgiDevice; DX::ThrowIfFailed( m_d3dDevice.As(&dxgiDevice) ); // Ensure that DXGI does not queue more than one frame at a time. This both reduces // latency and ensures that the application will only render after each VSync, minimizing // power consumption. DX::ThrowIfFailed( dxgiDevice-SetMaximumFrameLatency(1) ); // Next, get the parent factory from the DXGI Device. ComPtr dxgiAdapter; DX::ThrowIfFailed( dxgiDevice-GetAdapter(&dxgiAdapter) ); ComPtr dxgiFactory; DX::ThrowIfFailed( dxgiAdapter-GetParent( __uuidof(IDXGIFactory2), &dxgiFactory ) ); // Finally, create the swap chain. DX::ThrowIfFailed( dxgiFactory-CreateSwapChainForImmersiveWindow( m_d3dDevice.Get(), DX::GetIUnknown(m_window), &swapChainDesc, nullptr, // allow on all displays &m_swapChain ) ); } // Once the swap chain is created, create a render target view. This will // allow Direct3D to render graphics to the window. ComPtr backBuffer; DX::ThrowIfFailed( m_swapChain-GetBuffer( 0, __uuidof(ID3D11Texture2D), &backBuffer ) ); DX::ThrowIfFailed( m_d3dDevice-CreateRenderTargetView( backBuffer.Get(), nullptr, &m_renderTargetView ) ); // After the render target view is created, specify that the viewport, // which describes what portion of the window to draw to, should cover // the entire window. D3D11_TEXTURE2D_DESC backBufferDesc = {0}; backBuffer-GetDesc(&backBufferDesc); D3D11_VIEWPORT viewport; viewport.TopLeftX = 0.0f; viewport.TopLeftY = 0.0f; viewport.Width = static_cast(backBufferDesc.Width); viewport.Height = static_cast(backBufferDesc.Height); viewport.MinDepth = D3D11_MIN_DEPTH; viewport.MaxDepth = D3D11_MAX_DEPTH; m_d3dDeviceContext-RSSetViewports(1, &viewport); } }; // This class defines how to create the custom View Provider defined above. ref class Direct3DTutorialViewProviderFactory : IViewProviderFactory { public: IViewProvider^ CreateViewProvider() { return ref new Direct3DTutorialViewProvider(); } }; [Platform::MTAThread] int main(array^) { auto viewProviderFactory = ref new Direct3DTutorialViewProviderFactory(); Windows::ApplicationModel::Core::CoreApplication::Run(viewProviderFactory); return 0; }

    Read the article

  • Dual Boot issues with Windows 7 and Ubuntu

    - by Michael
    I'm finding myself in a rather unique situation. I've read through just about every resource I can find about this and while things have helped me understand some background, I haven't yet been able to find a solution. So I'm asking here. I originally had just a Windows 7 64-bit OS installation on my desktop. Learning that I couldn't do anything with Apache, PHP and MySql from within a 64-bit system, I did some research and found out that I could use Ubuntu. I've installed the latest version: 11.04. I created a CD to install Ubuntu from and the install went just fine. I installed it side-by-side with Windows 7. I can boot into Ubuntu just fine through the dual-boot option. When I reboot to load Windows though, the Grub2 list shows Windows 7 (loader) and when I select this option the Windows System Recovery loads instead of the actual OS. I haven't made it past there because I didn't know what to do. I just shut the computer down and rebooted into Ubuntu. I've been working for the last hour and a half to try to figure out how to boot into the Windows 7 OS and I haven't got a clue. While I'm somewhat proficient with Windows 7, I'm totally new to Ubuntu, so if you do know what needs to happen, please keep it simple enough that I'll be able to understand. Thanks for all your help in advance. Here's the results after using the Boot Info Script: Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #5 for cbh. => Windows is installed in the MBR of /dev/sdb => Grub 2 is installed in the MBR of /dev/mapper/pdc_bdadcfbdif and looks on the same drive in partition #5 for cbh. sda1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sda2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sda3: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sdb1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /Boot/BCD sdb2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb3: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /boot/BCD sdb4: _________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb6: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: pdc_bdadcfbdif1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /Boot/BCD pdc_bdadcfbdif2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files/dirs: /bootmgr /Boot/BCD /Windows/System32/winload.exe pdc_bdadcfbdif3: _________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy mount: unknown filesystem type '' =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sda1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/sda2 206,911 1,440,372,735 1,440,165,825 7 HPFS/NTFS /dev/sda3 1,440,372,736 1,464,856,575 24,483,840 7 HPFS/NTFS Drive: sdb ___________________ _____________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sdb1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/sdb2 206,911 1,342,554,688 1,342,347,778 7 HPFS/NTFS /dev/sdb3 1,930,344,448 1,953,521,663 23,177,216 7 HPFS/NTFS /dev/sdb4 1,342,556,158 1,930,344,447 587,788,290 5 Extended /dev/sdb5 1,342,556,160 1,896,806,399 554,250,240 83 Linux /dev/sdb6 1,896,808,448 1,930,344,447 33,536,000 82 Linux swap / Solaris Drive: pdc_bdadcfbdif ___________________ _____________________________________________________ Disk /dev/mapper/pdc_bdadcfbdif: 750.0 GB, 749999947776 bytes 255 heads, 63 sectors/track, 91182 cylinders, total 1464843648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/mapper/pdc_bdadcfbdif1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif2 206,911 1,440,372,735 1,440,165,825 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif3 1,440,372,736 1,464,856,575 24,483,840 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif3 ends after the last sector of /dev/mapper/pdc_bdadcfbdif blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/mapper/pdc_bdadcfbdif1 888E54CC8E54B482 ntfs SYSTEM /dev/mapper/pdc_bdadcfbdif2 C2766BF6766BEA1D ntfs OS /dev/mapper/pdc_bdadcfbdif: PTTYPE="dos" /dev/sda1 888E54CC8E54B482 ntfs SYSTEM /dev/sda2 C2766BF6766BEA1D ntfs OS /dev/sda3 BE6CA31D6CA2CF87 ntfs HP_RECOVERY /dev/sda promise_fasttrack_raid_member /dev/sdb1 20B65685B6565B7C ntfs SYSTEM /dev/sdb2 B4467A314679F508 ntfs HP /dev/sdb3 6E10B7A410B77227 ntfs FACTORY_IMAGE /dev/sdb4: PTTYPE="dos" /dev/sdb5 266f9801-cf4f-4acc-affa-2092be035f0c ext4 /dev/sdb6 1df35749-a887-45ff-a3de-edd52239847d swap /dev/sdb: PTTYPE="dos" error: /dev/mapper/pdc_bdadcfbdif3: No such file or directory error: /dev/sdc: No medium found error: /dev/sdd: No medium found error: /dev/sde: No medium found error: /dev/sdf: No medium found error: /dev/sdg: No medium found ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sdb5 / ext4 (rw,errors=remount-ro,commit=0) =========================== sdb5/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux /boot/vmlinuz-2.6.38-8-generic-pae root=UUID=266f9801-cf4f-4acc- affa-2092be035f0c ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.38-8-generic-pae } menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c echo 'Loading Linux 2.6.38-8-generic-pae ...' linux /boot/vmlinuz-2.6.38-8-generic-pae root=UUID=266f9801-cf4f-4acc-affa-2092be035f0c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.38-8-generic-pae } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sdb1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(/dev/sdb,msdos1)' search --no-floppy --fs-uuid --set=root 20B65685B6565B7C chainloader +1 } menuentry "Windows Recovery Environment (loader) (on /dev/sdb3)" --class windows --class os { insmod part_msdos insmod ntfs set root='(/dev/sdb,msdos3)' search --no-floppy --fs-uuid --set=root 6E10B7A410B77227 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sdb5/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sdb5 during installation UUID=266f9801-cf4f-4acc-affa-2092be035f0c / ext4 errors=remount-ro 0 1 # swap was on /dev/sdb6 during installation UUID=1df35749-a887-45ff-a3de-edd52239847d none swap sw 0 0 =================== sdb5: Location of files loaded by Grub: =================== 900.1GB: boot/grub/core.img 825.0GB: boot/grub/grub.cfg 688.7GB: boot/initrd.img-2.6.38-8-generic-pae 688.0GB: boot/vmlinuz-2.6.38-8-generic-pae 688.7GB: initrd.img 688.0GB: vmlinuz =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on pdc_bdadcfbdif3 =======Devices which don't seem to have a corresponding hard drive============== sdc sdd sde sdf sdg =============================== StdErr Messages: =============================== ERROR: dos: partition address past end of RAID device hexdump: /dev/mapper/pdc_bdadcfbdif3: No such file or directory hexdump: /dev/mapper/pdc_bdadcfbdif3: No such file or directory ERROR: dos: partition address past end of RAID device

    Read the article

  • Problem bash completion apt-get 12.10

    - by dadexix86
    I've got an annoying problem with completion and sudo apt-get. To give an example: $ sudo apt-get in[Tab][Tab] in intel_bios_reader includeres intel_disable_clock_gating indicator-multiload intel_dpio_read info intel_dpio_write infobrowser intel_error_decode infocmp intel_forcewaked infokey intel_gpu_abrt infotocap intel_gpu_time inimf intel_gpu_top init intel_gtt init-checkconf intel_l3_parity initctl intel_reg_checker initctl2dot intel_reg_dumper initex intel_reg_read inkscape intel_reg_snapshot inkview intel_reg_write inputattach intel_sprite_on insmod intel_stepping install intel_upload_blit_large install-docs intel_upload_blit_large_gtt installfont-tl intel_upload_blit_large_map install-info intel_upload_blit_small installkernel interdiff --More-- While is working right both with just apt-get or doing it in root: $ apt-get in[Tab]stall $ sudo -i [sudo] password for davide: root@brenna:~# apt-get in[Tab]stall So the problem is using autocompletion after sudo? Not really, because $ sudo apt-[Tab][Tab] apt-add-repository apt-extracttemplates apt-key apt-cache apt-file apt-mark apt-cdrom apt-ftparchive apt-sortpkgs apt-config apt-get Summing up, the problem seems to be using sudo and auto-completion for programs options together. Any good advice for that?

    Read the article

  • How ISP or dns server find the nameserevr [on hold]

    - by IT researcher
    I saw some articles about how DNS propagation happens.I know that ISP or DNS server(such as google public dns) cache the ip address of website which it uses to convert domain name to ip address. But my doubt is from where these ISP or dns serevr know which nameserver to go for particular domain name. for example a domain.com has two name servers ns1.domain.com and ns2.domain.com. But how the ISP server or dns server know that it uses these name server and i have to send request to this name server.So where does this record mainatined?

    Read the article

  • Cocoon lite / XML and XSLT publishing framework

    - by bambax
    What publishing frameworks (publishing only, NOT full-blown CMS) based on XML, XSLT sitemaps and pipelines exist, are stable, active, and simpler / lighter than Cocoon? I have glanced at: mod_xslt (http://www.mod-xslt2.com/) which seemed to be exactly that, but looks all but dead, and required a complex setup, and apparently supported only libxslt as an XSLT processor (I'd like to be able to use Saxon and XSLT 2.0 of course). Apache Forrest (http://forrest.apache.org/), but I don't understand if it is really simpler than Cocoon or is rather an additionnal thing on top of Cocoon? What I'm looking for is something that does just this: recieves an HTTP GET "runs it" through a sitemap finds a pipeline: source.xml - xslt1.xsl - xslt2.xsl - xsltn.xsl - serialize runs the pipeline serves the serialized result to the client and: uses Saxon (or is "processor independant") can be installed "lightly", that is: should not require much more configuration than the sitemap Maybe I'm describing an early version of Cocoon, or a future version of an XProc implementation... Anyway, does such a tool exist?

    Read the article

  • Trace File Source Adapter

    The Trace File Source adapter is a useful addition to your SSIS toolbox.  It allows you to read 2005 and 2008 profiler traces stored as .trc files and read them into the Data Flow.  From there you can perform filtering and analysis using the power of SSIS. There is no need for a SQL Server connection this just uses the trace file. Example Usages Cache warming for SQL Server Analysis Services Reading the flight recorder Find out the longest running queries on a server Analyze statements for CPU, memory by user or some other criteria you choose Properties The Trace File Source adapter has two properties, both of which combine to control the source trace file that is read at runtime. SQL Server 2005 and SQL Server 2008 trace files are supported for both the Database Engine (SQL Server) and Analysis Services. The properties are managed by the Editor form or can be set directly from the Properties Grid in Visual Studio. Property Type Description AccessMode Enumeration This property determines how the Filename property is interpreted. The values available are: DirectInput Variable Filename String This property holds the path for trace file to load (*.trc). The value is either a full path, or the name of a variable which contains the full path to the trace file, depending on the AccessMode property. Trace Column Definition Hopefully the majority of you can skip this section entirely, but if you encounter some problems processing a trace file this may explain it and allow you to fix the problem. The component is built upon the trace management API provided by Microsoft. Unfortunately API methods that expose the schema of a trace file have known issues and are unreliable, put simply the data often differs from what was specified. To overcome these limitations the component uses  some simple XML files. These files enable the trace column data types and sizing attributes to be overridden. For example SQL Server Profiler or TMO generated structures define EventClass as an integer, but the real value is a string. TraceDataColumnsSQL.xml  - SQL Server Database Engine Trace Columns TraceDataColumnsAS.xml    - SQL Server Analysis Services Trace Columns The files can be found in the %ProgramFiles%\Microsoft SQL Server\100\DTS\PipelineComponents folder, e.g. "C:\Program Files\Microsoft SQL Server\100\DTS\PipelineComponents\TraceDataColumnsSQL.xml" "C:\Program Files\Microsoft SQL Server\100\DTS\PipelineComponents\TraceDataColumnsAS.xml" If at runtime the component encounters a type conversion or sizing error it is most likely due to a discrepancy between the column definition as reported by the API and the actual value encountered. Whilst most common issues have already been fixed through these files we have implemented specific exception traps to direct you to the files to enable you to fix any further issues due to different usage or data scenarios that we have not tested. An example error that you can fix through these files is shown below. Buffer exception writing value to column 'Column Name'. The string value is 999 characters in length, the column is only 111. Columns can be overridden by the TraceDataColumns XML files in "C:\Program Files\Microsoft SQL Server\100\DTS\PipelineComponents\TraceDataColumnsAS.xml". Installation The component is provided as an MSI file which you can download and run to install it. This simply places the files on disk in the correct locations and also installs the assemblies in the Global Assembly Cache as per Microsoft’s recommendations. You may need to restart the SQL Server Integration Services service, as this caches information about what components are installed, as well as restarting any open instances of Business Intelligence Development Studio (BIDS) / Visual Studio that you may be using to build your SSIS packages. Finally you will have to add the transformation to the Visual Studio toolbox manually. Right-click the toolbox, and select Choose Items.... Select the SSIS Data Flow Items tab, and then check the Trace File Source transformation in the Choose Toolbox Items window. This process has been described in detail in the related FAQ entry for How do I install a task or transform component? We recommend you follow best practice and apply the current Microsoft SQL Server Service pack to your SQL Server servers and workstations. Please note that the Microsoft Trace classes used in the component are not supported on 64-bit platforms. To use the Trace File Source on a 64-bit host you need to ensure you have the 32-bit (x86) tools available, and the way you execute your package is setup to use them, please see the help topic 64-bit Considerations for Integration Services for more details. Downloads Trace Sources for SQL Server 2005 -- Trace Sources for SQL Server 2008 Version History SQL Server 2008 Version 2.0.0.382 - SQL Sever 2008 public release. (9 Apr 2009) SQL Server 2005 Version 1.0.0.321 - SQL Server 2005 public release. (18 Nov 2008) -- Screenshots

    Read the article

  • Ubuntu Sudo apt-get -f install

    - by Justin
    I was trying to install a program. And It said that my Dependencies were unmet. And that I should run, sudo apt-get -f install. I have moved everything I didn't need in /etc/apt/sources.list.d/ into the trash. My source.list is all Natty while I am running Oneiric. So maybe I need a new source.list? But here are the things I have: justin@justin-000:~$ sudo apt-get -f install [sudo] password for justin: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: linux-image-3.0.0-13-generic Suggested packages: fdutils linux-doc-3.0.0 linux-source-3.0.0 linux-tools The following NEW packages will be installed: linux-image-3.0.0-13-generic 0 upgraded, 1 newly installed, 0 to remove and 3 not upgraded. 2 not fully installed or removed. Need to get 0 B/36.5 MB of archives. After this operation, 117 MB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 270736 files and directories currently installed.) Unpacking linux-image-3.0.0-13-generic (from .../linux-image-3.0.0-13- generic_3.0.0-13.22_i386.deb) ... Done. dpkg: error processing /var/cache/apt/archives/linux-image-3.0.0-13 generic_3.0.0-13.22_i386.deb (--unpack): corrupted filesystem tarfile - corrupted package archive No apport report written because MaxReports is reached already dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.0.0-13-generic /boot/vmlinuz-3.0.0-13-generic run-parts: executing /etc/kernel/postrm.d/zz-extlinux 3.0.0-13-generic /boot/vmlinuz-3.0.0-13-generic P: Checking for EXTLINUX directory... found. P: Writing config for /boot/vmlinuz-3.0.0-12-generic... P: Writing config for /boot/vmlinuz-2.6.38-11-generic... P: Installing debian theme... done. run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.0.0-13-generic /boot/vmlinuz-3.0.0-13-generic Errors were encountered while processing: /var/cache/apt/archives/linux-image-3.0.0-13-generic_3.0.0-13.22_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) justin@justin-000:~$ sudo apt-get update justin@justin-000:~$ sudo apt-get update Ign dl.google.com stable InRelease Ign dl.google.com stable InRelease Get:1dl.google.com stable Release.gpg [198 B] Ign us.archive.ubuntu.com oneiric InRelease Ign us.archive.ubuntu.com oneiric-security InRelease Ign http://us.archive.ubuntu.com oneiric-updates InRelease Get:2 dl.google.com stable Release.gpg [198 B] Get:3 dl.google.com stable Release [1,347 B] Get:4 dl.google.com stable Release [1,338 B] Hit us.archive.ubuntu.com oneiric Release.gpg Hit us.archive.ubuntu.com oneiric-security Release.gpg Get:5/dl.google.com stable/main i386 Packages [1,220 B] Hit tp://us.archive.ubuntu.com oneiric-updates Release.gpg Ign tp://dl.google.com stable/main TranslationIndex Get:6 tp://dl.google.com stable/main i386 Packages [464 B] Ign ttp://ppa.launchpad.net oneiric InRelease Hit ttp://us.archive.ubuntu.com oneiric Release Ign ttp://ppa.launchpad.net oneiric InRelease Ign ttp://dl.google.com stable/main TranslationIndex Hit ttp://ppa.launchpad.net oneiric Release.gpg Hit ttp://us.archive.ubuntu.com oneiric-security Release Hit ttp://ppa.launchpad.net oneiric Release.gpg Hit ttp://us.archive.ubuntu.com oneiric-updates Release Hit ttp://us.archive.ubuntu.com oneiric/main Sources Hit ttp://us.archive.ubuntu.com oneiric/restricted Sources Hit ttp://us.archive.ubuntu.com oneiric/universe Sources Hit ttp://us.archive.ubuntu.com oneiric/multiverse Sources Hit ttp://us.archive.ubuntu.com oneiric/main i386 Packages Hit ttp://ppa.launchpad.net oneiric Release Hit ttp://us.archive.ubuntu.com oneiric/restricted i386 Packages Hit ttp://us.archive.ubuntu.com oneiric/universe i386 Packages Hit ttp://us.archive.ubuntu.com oneiric/multiverse i386 Packages Hit ttp://us.archive.ubuntu.com oneiric/main TranslationIndex Hit ttp://us.archive.ubuntu.com oneiric/multiverse TranslationIndex Hit ://us.archive.ubuntu.com oneiric/restricted TranslationIndex Hit htp://us.archive.ubuntu.com oneiric/universe TranslationIndex Hit htp://us.archive.ubuntu.com oneiric-security/main Sources Hit ttp://us.archive.ubuntu.com oneiric-security/restricted Sources Hit ttp://ppa.launchpad.net oneiric Release Hit ttp://us.archive.ubuntu.com oneiric-security/universe Sources Hit tp://us.archive.ubuntu.com oneiric-security/multiverse Sources Hit htp://us.archive.ubuntu.com oneiric-security/main i386 Packages Hit tp://us.archive.ubuntu.com oneiric-security/restricted i386 Packages Hit ttp://us.archive.ubuntu.com oneiric-security/universe i386 Packages Hit ttp://us.archive.ubuntu.com oneiric-security/multiverse i386 Packages Hit htp://ppa.launchpad.net oneiric/main Sources Hit ttp://ppa.launchpad.net oneiric/main i386 Packages Ign htp://ppa.launchpad.net oneiric/main TranslationIndex Hit ttp://us.archive.ubuntu.com oneiric-security/main TranslationIndex Hit ttp://us.archive.ubuntu.com oneiric-security/multiverse TranslationIndex Hit htp://us.archive.ubuntu.com oneiric-security/restricted TranslationIndex Hit htp://us.archive.ubuntu.com oneiric-security/universe TranslationIndex Ign htp://dl.google.com stable/main Translation-en_US Hit htp://us.archive.ubuntu.com oneiric-updates/main Sources Hit htp://us.archive.ubuntu.com oneiric-updates/restricted Sources Hit tp://us.archive.ubuntu.com oneiric-updates/universe Sources Hit htp://us.archive.ubuntu.com oneiric-updates/multiverse Sources Hit htp://us.archive.ubuntu.com oneiric-updates/main i386 Packages Ign htp://dl.google.com stable/main Translation-en Hit ttp://ppa.launchpad.net oneiric/main Sources Hit htp://ppa.launchpad.net oneiric/main i386 Packages Hit ttp://us.archive.ubuntu.com oneiric-updates/restricted i386 Packages Ign htp://dl.google.com stable/main Translation-en_US Ign htp://ppa.launchpad.net oneiric/main TranslationIndex Hit hp://us.archive.ubuntu.com oneiric-updates/universe i386 Packages Hit ttp://us.archive.ubuntu.com oneiric-updates/multiverse i386 Packages Hit htp://us.archive.ubuntu.com oneiric-updates/main TranslationIndex Hit htp://us.archive.ubuntu.com oneiric-updates/multiverse TranslationIndex Hit htp://us.archive.ubuntu.com oneiric-updates/restricted TranslationIndex Ign htp://dl.google.com stable/main Translation-en Hit htp://us.archive.ubuntu.com oneiric-updates/universe TranslationIndex Hit ttp://us.archive.ubuntu.com oneiric/main Translation-en Hit ttp://us.archive.ubuntu.com oneiric/multiverse Translation-en Hit htp://us.archive.ubuntu.com oneiric/restricted Translation-en Hit htp://us.archive.ubuntu.com oneiric/universe Translation-en Hit htp://us.archive.ubuntu.com oneiric-security/main Translation-en Hit hp://us.archive.ubuntu.com oneiric-security/multiverse Translation-en Hit htp://us.archive.ubuntu.com oneiric-security/restricted Translation-en Hit htp://us.archive.ubuntu.com oneiric-security/universe Translation-en Hit htp://us.archive.ubuntu.com oneiric-updates/main Translation-en Hit htp://us.archive.ubuntu.com oneiric-updates/multiverse Translation-en Hit htp://us.archive.ubuntu.com oneiric-updates/restricted Translation-en Hit htp://us.archive.ubuntu.com oneiric-updates/universe Translation-en Ign htp://ppa.launchpad.net oneiric/main Translation-en_US Ign htt://ppa.launchpad.net oneiric/main Translation-en Ign htp://ppa.launchpad.net oneiric/main Translation-en_US Ign htp://ppa.launchpad.net oneiric/main Translation-en Fetched 4,765 B in 2s (2,158 B/s) Reading package lists... Done justin@justin-000:~$

    Read the article

  • What is New in ASP.NET 4 Web Development Overview

    - by Aamir Hasan
     Microsoft Recently Microsoft introduce Visual  studio 2010 which have new feature's Name of some new Features are given below. In ASP.NET 4.O has focus on performance and Search Engine Optimization. I'll be taking a look at what I think are the most important new features in ASP.NET 4.Output cache extensibility Session state compression View state mode for individual control Page.MetaKeyword and Page.MetaDescription properties Response.RedirectPermanent method Routing in ASP.NET Increase the URL character length New syntax for Html Encode Predictable Client IDs Web.config file refactoring Auto-Start ASP.NET applications Improvements on Microsoft Ajax LibraryReference:ASP.NET 4 and Visual Studio 2010 Web Development Overview 

    Read the article

  • Le C++ expressif n° 1 : introduction, un article d'Eric Niebler traduit par Timothée Bernard

    Dissimulé dans C++ se cache un autre langage - d'innombrables autres langages, en fait - tous sont meilleurs que le C++ pour résoudre certains types de problèmes. Ces domain-specific languages (abrégé DSL) sont par exemple des langages pour l'algèbre linéaire ou des langages de requêtes, ils ne peuvent faire qu'une seule chose, mais ils le font bien. On peut créer et utiliser ces langages directement dans le C++, en utilisant la puissance et la flexibilité du C++ pour remplacer les parties communes du langage par les parties spécifiques au domaine que nous utilisons. Dans cette série d'article, Eric Niebler regarde de près les domain-specific languages, dans quels domaines ils sont utiles et comment on peut facilement les implémenter en C++ avec l'aide de

    Read the article

  • Getting a Web Resource Url in non WebForms Applications

    - by Rick Strahl
    WebResources in ASP.NET are pretty useful feature. WebResources are resources that are embedded into a .NET assembly and can be loaded from the assembly via a special resource URL. WebForms includes a method on the ClientScriptManager (Page.ClientScript) and the ScriptManager object to retrieve URLs to these resources. For example you can do: ClientScript.GetWebResourceUrl(typeof(ControlResources), ControlResources.JQUERY_SCRIPT_RESOURCE); GetWebResourceUrl requires a type (which is used for the assembly lookup in which to find the resource) and the resource id to lookup. GetWebResourceUrl() then returns a nasty old long URL like this: WebResource.axd?d=-b6oWzgbpGb8uTaHDrCMv59VSmGhilZP5_T_B8anpGx7X-PmW_1eu1KoHDvox-XHqA1EEb-Tl2YAP3bBeebGN65tv-7-yAimtG4ZnoWH633pExpJor8Qp1aKbk-KQWSoNfRC7rQJHXVP4tC0reYzVw2&t=634533278261362212 While lately excessive resource usage has been frowned upon especially by MVC developers who tend to opt for content distributed as files, I still think that Web Resources have their place even in non-WebForms applications. Also if you have existing assemblies that include resources like scripts and common image links it sure would be nice to access them from non-WebForms pages like MVC views or even in plain old Razor Web Pages. Where's my Page object Dude? Unfortunately natively ASP.NET doesn't have a mechanism for retrieving WebResource Urls outside of the WebForms engine. It's a feature that's specifically baked into WebForms and that relies specifically on the Page HttpHandler implementation. Both Page.ClientScript (obviously) and ScriptManager rely on a hosting Page object in order to work and the various methods off these objects require control instances passed. The reason for this is that the script managers can inject scripts and links into Page content (think RegisterXXXX methods) and for that a Page instance is required. However, for many other methods - like GetWebResourceUrl() - that simply return resources or resource links the Page reference is really irrelevant. While there's a separate ClientScriptManager class, it's marked as sealed and doesn't have any public constructors so you can't create your own instance (without Reflection). Even if it did the internal constructor it does have requires a Page reference. No good… So, can we get access to a WebResourceUrl generically without running in a WebForms Page instance? We just have to create a Page instance ourselves and use it internally. There's nothing intrinsic about the use of the Page class in ClientScript, at least for retrieving resources and resource Urls so it's easy to create an instance of a Page for example in a static method. For our needs of retrieving ResourceUrls or even actually retrieving script resources we can use a canned, non-configured Page instance we create on our own. The following works just fine: public static string GetWebResourceUrl(Type type, string resource ) { Page page = new Page(); return page.ClientScript.GetWebResourceUrl(type, resource); } A slight optimization for this might be to cache the created Page instance. Page tends to be a pretty heavy object to create each time a URL is required so you might want to cache the instance: public class WebUtils { private static Page CachedPage { get { if (_CachedPage == null) _CachedPage = new Page(); return _CachedPage; } } private static Page _CachedPage; public static string GetWebResourceUrl(Type type, string resource) { return CachedPage.ClientScript.GetWebResourceUrl(type, resource); } } You can now use GetWebResourceUrl in a Razor page like this: <!DOCTYPE html> <html <head> <script src="@WebUtils.GetWebResourceUrl(typeof(ControlResources),ControlResources.JQUERY_SCRIPT_RESOURCE)"> </script> </head> <body> <div class="errordisplay"> <img src="@WebUtils.GetWebResourceUrl(typeof(ControlResources),ControlResources.WARNING_ICON_RESOURCE)" /> This is only a Test! </div> </body> </html> And voila - there you have WebResources served from a non-Page based application. WebResources may be a on the way out, but legacy apps have them embedded and for some situations, like fallback scripts and some common image resources I still like to use them. Being able to use them from non-WebForms applications should have been built into the core ASP.NETplatform IMHO, but seeing that it's not this workaround is easy enough to implement.© Rick Strahl, West Wind Technologies, 2005-2011Posted in ASP.NET  MVC   Tweet (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • SQL SERVER – PAGELATCH_DT, PAGELATCH_EX, PAGELATCH_KP, PAGELATCH_SH, PAGELATCH_UP – Wait Type – Day 12 of 28

    - by pinaldave
    This is another common wait type. However, I still frequently see people getting confused with PAGEIOLATCH_X and PAGELATCH_X wait types. Actually, there is a big difference between the two. PAGEIOLATCH is related to IO issues, while PAGELATCH is not related to IO issues but is oftentimes linked to a buffer issue. Before we delve deeper in this interesting topic, first let us understand what Latch is. Latches are internal SQL Server locks which can be described as very lightweight and short-term synchronization objects. Latches are not primarily to protect pages being read from disk into memory. It’s a synchronization object for any in-memory access to any portion of a log or data file.[Updated based on comment of Paul Randal] The difference between locks and latches is that locks seal all the involved resources throughout the duration of the transactions (and other processes will have no access to the object), whereas latches locks the resources during the time when the data is changed. This way, a latch is able to maintain the integrity of the data between storage engine and data cache. A latch is a short-living lock that is put on resources on buffer cache and in the physical disk when data is moved in either directions. As soon as the data is moved, the latch is released. Now, let us understand the wait stat type  related to latches. From Book On-Line: PAGELATCH_DT Occurs when a task is waiting on a latch for a buffer that is not in an I/O request. The latch request is in Destroy mode. PAGELATCH_EX Occurs when a task is waiting on a latch for a buffer that is not in an I/O request. The latch request is in Exclusive mode. PAGELATCH_KP Occurs when a task is waiting on a latch for a buffer that is not in an I/O request. The latch request is in Keep mode. PAGELATCH_SH Occurs when a task is waiting on a latch for a buffer that is not in an I/O request. The latch request is in Shared mode. PAGELATCH_UP Occurs when a task is waiting on a latch for a buffer that is not in an I/O request. The latch request is in Update mode. PAGELATCH_X Explanation: When there is a contention of access of the in-memory pages, this wait type shows up. It is quite possible that some of the pages in the memory are of very high demand. For the SQL Server to access them and put a latch on the pages, it will have to wait. This wait type is usually created at the same time. Additionally, it is commonly visible when the TempDB has higher contention as well. If there are indexes that are heavily used, contention can be created as well, leading to this wait type. Reducing PAGELATCH_X wait: The following counters are useful to understand the status of the PAGELATCH: Average Latch Wait Time (ms): The wait time for latch requests that have to wait. Latch Waits/sec: This is the number of latch requests that could not be granted immediately. Total Latch Wait Time (ms): This is the total latch wait time for latch requests in the last second. If there is TempDB contention, I suggest that you read the blog post of Robert Davis right away. He has written an excellent blog post regarding how to find out TempDB contention. The same blog post explains the terms in the allocation of GAM, SGAM and PFS. If there was a TempDB contention, Paul Randal explains the optimal settings for the TempDB in his misconceptions series. Trace Flag 1118 can be useful but use it very carefully. I totally understand that this blog post is not as clear as my other blog posts. I suggest if this wait stats is on one of your higher wait type. Do leave a comment or send me an email and I will get back to you with my solution for your situation. May the looking at all other wait stats and types together become effective as this wait type can help suggest proper bottleneck in your system. Read all the post in the Wait Types and Queue series. Note: The information presented here is from my experience and there is no way that I claim it to be accurate. I suggest reading Book OnLine for further clarification. All the discussions of Wait Stats in this blog are generic and vary from system to system. It is recommended that you test this on a development server before implementing it to a production server. Reference: Pinal Dave (http://blog.SQLAuthority.com)   Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

    Read the article

  • Recover Data Like a Forensics Expert Using an Ubuntu Live CD

    - by Trevor Bekolay
    There are lots of utilities to recover deleted files, but what if you can’t boot up your computer, or the whole drive has been formatted? We’ll show you some tools that will dig deep and recover the most elusive deleted files, or even whole hard drive partitions. We’ve shown you simple ways to recover accidentally deleted files, even a simple method that can be done from an Ubuntu Live CD, but for hard disks that have been heavily corrupted, those methods aren’t going to cut it. In this article, we’ll examine four tools that can recover data from the most messed up hard drives, regardless of whether they were formatted for a Windows, Linux, or Mac computer, or even if the partition table is wiped out entirely. Note: These tools cannot recover data that has been overwritten on a hard disk. Whether a deleted file has been overwritten depends on many factors – the quicker you realize that you want to recover a file, the more likely you will be able to do so. Our setup To show these tools, we’ve set up a small 1 GB hard drive, with half of the space partitioned as ext2, a file system used in Linux, and half the space partitioned as FAT32, a file system used in older Windows systems. We stored ten random pictures on each hard drive. We then wiped the partition table from the hard drive by deleting the partitions in GParted. Is our data lost forever? Installing the tools All of the tools we’re going to use are in Ubuntu’s universe repository. To enable the repository, open Synaptic Package Manager by clicking on System in the top-left, then Administration > Synaptic Package Manager. Click on Settings > Repositories and add a check in the box labelled “Community-maintained Open Source software (universe)”. Click Close, and then in the main Synaptic Package Manager window, click the Reload button. Once the package list has reloaded, and the search index rebuilt, search for and mark for installation one or all of the following packages: testdisk, foremost, and scalpel. Testdisk includes TestDisk, which can recover lost partitions and repair boot sectors, and PhotoRec, which can recover many different types of files from tons of different file systems. Foremost, originally developed by the US Air Force Office of Special Investigations, recovers files based on their headers and other internal structures. Foremost operates on hard drives or drive image files generated by various tools. Finally, scalpel performs the same functions as foremost, but is focused on enhanced performance and lower memory usage. Scalpel may run better if you have an older machine with less RAM. Recover hard drive partitions If you can’t mount your hard drive, then its partition table might be corrupted. Before you start trying to recover your important files, it may be possible to recover one or more partitions on your drive, recovering all of your files with one step. Testdisk is the tool for the job. Start it by opening a terminal (Applications > Accessories > Terminal) and typing in: sudo testdisk If you’d like, you can create a log file, though it won’t affect how much data you recover. Once you make your choice, you’re greeted with a list of the storage media on your machine. You should be able to identify the hard drive you want to recover partitions from by its size and label. TestDisk asks you select the type of partition table to search for. In most cases (ext2/3, NTFS, FAT32, etc.) you should select Intel and press Enter. Highlight Analyse and press enter. In our case, our small hard drive has previously been formatted as NTFS. Amazingly, TestDisk finds this partition, though it is unable to recover it. It also finds the two partitions we just deleted. We are able to change their attributes, or add more partitions, but we’ll just recover them by pressing Enter. If TestDisk hasn’t found all of your partitions, you can try doing a deeper search by selecting that option with the left and right arrow keys. We only had these two partitions, so we’ll recover them by selecting Write and pressing Enter. Testdisk informs us that we will have to reboot. Note: If your Ubuntu Live CD is not persistent, then when you reboot you will have to reinstall any tools that you installed earlier. After restarting, both of our partitions are back to their original states, pictures and all. Recover files of certain types For the following examples, we deleted the 10 pictures from both partitions and then reformatted them. PhotoRec Of the three tools we’ll show, PhotoRec is the most user-friendly, despite being a console-based utility. To start recovering files, open a terminal (Applications > Accessories > Terminal) and type in: sudo photorec To begin, you are asked to select a storage device to search. You should be able to identify the right device by its size and label. Select the right device, and then hit Enter. PhotoRec asks you select the type of partition to search. In most cases (ext2/3, NTFS, FAT, etc.) you should select Intel and press Enter. You are given a list of the partitions on your selected hard drive. If you want to recover all of the files on a partition, then select Search and hit enter. However, this process can be very slow, and in our case we only want to search for pictures files, so instead we use the right arrow key to select File Opt and press Enter. PhotoRec can recover many different types of files, and deselecting each one would take a long time. Instead, we press “s” to clear all of the selections, and then find the appropriate file types – jpg, gif, and png – and select them by pressing the right arrow key. Once we’ve selected these three, we press “b” to save these selections. Press enter to return to the list of hard drive partitions. We want to search both of our partitions, so we highlight “No partition” and “Search” and then press Enter. PhotoRec prompts for a location to store the recovered files. If you have a different healthy hard drive, then we recommend storing the recovered files there. Since we’re not recovering very much, we’ll store it on the Ubuntu Live CD’s desktop. Note: Do not recover files to the hard drive you’re recovering from. PhotoRec is able to recover the 20 pictures from the partitions on our hard drive! A quick look in the recup_dir.1 directory that it creates confirms that PhotoRec has recovered all of our pictures, save for the file names. Foremost Foremost is a command-line program with no interactive interface like PhotoRec, but offers a number of command-line options to get as much data out of your had drive as possible. For a full list of options that can be tweaked via the command line, open up a terminal (Applications > Accessories > Terminal) and type in: foremost –h In our case, the command line options that we are going to use are: -t, a comma-separated list of types of files to search for. In our case, this is “jpeg,png,gif”. -v, enabling verbose-mode, giving us more information about what foremost is doing. -o, the output folder to store recovered files in. In our case, we created a directory called “foremost” on the desktop. -i, the input that will be searched for files. This can be a disk image in several different formats; however, we will use a hard disk, /dev/sda. Our foremost invocation is: sudo foremost –t jpeg,png,gif –o foremost –v –i /dev/sda Your invocation will differ depending on what you’re searching for and where you’re searching for it. Foremost is able to recover 17 of the 20 files stored on the hard drive. Looking at the files, we can confirm that these files were recovered relatively well, though we can see some errors in the thumbnail for 00622449.jpg. Part of this may be due to the ext2 filesystem. Foremost recommends using the –d command-line option for Linux file systems like ext2. We’ll run foremost again, adding the –d command-line option to our foremost invocation: sudo foremost –t jpeg,png,gif –d –o foremost –v –i /dev/sda This time, foremost is able to recover all 20 images! A final look at the pictures reveals that the pictures were recovered with no problems. Scalpel Scalpel is another powerful program that, like Foremost, is heavily configurable. Unlike Foremost, Scalpel requires you to edit a configuration file before attempting any data recovery. Any text editor will do, but we’ll use gedit to change the configuration file. In a terminal window (Applications > Accessories > Terminal), type in: sudo gedit /etc/scalpel/scalpel.conf scalpel.conf contains information about a number of different file types. Scroll through this file and uncomment lines that start with a file type that you want to recover (i.e. remove the “#” character at the start of those lines). Save the file and close it. Return to the terminal window. Scalpel also has a ton of command-line options that can help you search quickly and effectively; however, we’ll just define the input device (/dev/sda) and the output folder (a folder called “scalpel” that we created on the desktop). Our invocation is: sudo scalpel /dev/sda –o scalpel Scalpel is able to recover 18 of our 20 files. A quick look at the files scalpel recovered reveals that most of our files were recovered successfully, though there were some problems (e.g. 00000012.jpg). Conclusion In our quick toy example, TestDisk was able to recover two deleted partitions, and PhotoRec and Foremost were able to recover all 20 deleted images. Scalpel recovered most of the files, but it’s very likely that playing with the command-line options for scalpel would have enabled us to recover all 20 images. These tools are lifesavers when something goes wrong with your hard drive. If your data is on the hard drive somewhere, then one of these tools will track it down! Similar Articles Productive Geek Tips Recover Deleted Files on an NTFS Hard Drive from a Ubuntu Live CDUse an Ubuntu Live CD to Securely Wipe Your PC’s Hard DriveReset Your Ubuntu Password Easily from the Live CDBackup Your Windows Live Writer SettingsAdding extra Repositories on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook Recycle !

    Read the article

  • Installing gtk-config and/or fsv in Ubuntu 10.10

    - by Wayne Werner
    Hi, I'm trying to install the File System Visualizer (think "It's a UNIX System! I know this!" from Jurassic Park) on Ubuntu 10.10. I've got the .tar.gz downloaded, and extracted. However, when I ./configure, I get this output: loading cache ./config.cache checking for a BSD compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking whether make sets ${MAKE}... yes checking for working aclocal... found checking for working autoconf... found checking for working automake... found checking for working autoheader... found checking for working makeinfo... missing checking for gcc... gcc checking whether the C compiler (gcc ) works... yes checking whether the C compiler (gcc ) is a cross-compiler... no checking whether we are using GNU C... yes checking whether gcc accepts -g... yes checking how to run the C preprocessor... gcc -E checking for ranlib... ranlib checking for POSIXized ISC... no checking for dirent.h that defines DIR... yes checking for opendir in -ldir... no checking for ANSI C header files... yes checking whether time.h and sys/time.h may both be included... yes checking for strings.h... yes checking for sys/time.h... yes checking for unistd.h... yes checking for working const... yes checking for mode_t... yes checking for uid_t in sys/types.h... yes checking for pid_t... yes checking for size_t... yes checking for comparison_fn_t... yes checking for st_blocks in struct stat... yes checking whether struct tm is in sys/time.h or time.h... time.h checking for working alloca.h... yes checking for alloca... yes checking for working fnmatch... yes checking for strftime... yes checking for getcwd... yes checking for gettimeofday... yes checking for mktime... yes checking for strcspn... yes checking for strdup... yes checking for strspn... yes checking for strtod... yes checking for strtoul... yes checking for scandir... yes checking for inline... inline checking for off_t... yes checking for unistd.h... (cached) yes checking for getpagesize... yes checking for working mmap... yes checking for argz.h... yes checking for limits.h... yes checking for locale.h... yes checking for nl_types.h... yes checking for malloc.h... yes checking for string.h... yes checking for unistd.h... (cached) yes checking for sys/param.h... yes checking for getcwd... (cached) yes checking for munmap... yes checking for putenv... yes checking for setenv... yes checking for setlocale... yes checking for strchr... yes checking for strcasecmp... yes checking for strdup... (cached) yes checking for __argz_count... yes checking for __argz_stringify... yes checking for __argz_next... yes checking for stpcpy... yes checking for LC_MESSAGES... yes checking whether NLS is requested... yes checking whether included gettext is requested... no checking for libintl.h... yes checking for gettext in libc... yes checking for msgfmt... /usr/bin/msgfmt checking for dcgettext... yes checking for gmsgfmt... /usr/bin/msgfmt checking for xgettext... /usr/bin/xgettext checking for gtk-config... no checking for GTK - version >= 1.2.1... no *** The gtk-config script installed by GTK could not be found *** If GTK was installed in PREFIX, make sure PREFIX/bin is in *** your path, or set the GTK_CONFIG environment variable to the *** full path to gtk-config. configure: error: Cannot find proper GTK+ version Obviously it's looking for gtk-config. However, apparently it doesn't exist in the repos anymore. Then this post mentioned that gtkglarea solved their problem, as mentioned in this file. Of course that poster neatly forgets to mention exactly what and how gtkglarea solved their problem, and Google is mostly devoid of information on the problem. So I come here asking for help! I would like to install fsv, but it tells me gtk-config doesn't exist. How can I fix this problem in Ubuntu 10.10? Thanks!

    Read the article

  • Cannot install any software from the Software Center due to ttf-mscorefonts-installer package error

    - by Dei
    When I try to install any software from ubuntu software center it comes with error: An unhandled error occured There seems to be a programming error in aptdaemon. This is the software that allows you to install/remove software and to perform other package management related tasks. details Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/aptdaemon/worker.py", line 961, in simulate trans.unauthenticated = self._simulate_helper(trans) File "/usr/lib/python2.7/dist-packages/aptdaemon/worker.py", line 1085, in _simulate_helper return depends, self._cache.required_download, \ File "/usr/lib/python2.7/dist-packages/apt/cache.py", line 226, in required_download pm.get_archives(fetcher, self._list, self._records) SystemError: E:I wasn't able to locate file for the ttf-mscorefonts-installer package. This might mean you need to manually fix this package. Please help me!

    Read the article

  • Homebrew LEGO CD Duplicator Copies CDs On The Cheap

    - by Jason Fitzpatrick
    If you’d like to bulk copy CDs/DVDs without the sticker shock of a $500+ commercial duplicator, this DIY LEGO duplicator is a homebrew solution. Paul Rea wanted to rip and copy CDs and DVDs without shelling out for a commercial duplicator and without the hassle of being bound to that commercial duplicator’s propriety software. His homebrew solution–a combination of LEGO, a rotating base, an Arduino controller, and little ingenuity–handles his ripping and copying needs with ease. Watch the video above to see it in action then hit up the link below for the build log and Arduino code. CD Duplicator [PaulRea.net via Make] HTG Explains: Understanding Routers, Switches, and Network Hardware How to Use Offline Files in Windows to Cache Your Networked Files Offline How to See What Web Sites Your Computer is Secretly Connecting To

    Read the article

  • Minidlna Directory Issues

    - by Somnambulist
    I've done my searching and can't find an answer to THIS specific issue. I have my minidlna set up and running - but it's not really done properly. First off, when I open the server on my bluray player, all of my movies are listed twice - when they are certainly not saved on my external twice. Second, when I open the server - rather than reading "Movies" "TV" "Music", etc - It just mashes all of my movies, tv, and some other folders all together with no real organization. I never had this problem when I had my Windows set up, so I know it's something configured improperly more-so than my external drive giving me gruff. Here's my minidlna.conf file: # This is the configuration file for the MiniDLNA daemon, a DLNA/UPnP-AV media # server. # # Unless otherwise noted, the commented out options show their default value. # # On Debian, you can also refer to the minidlna.conf(5) man page for # documentation about this file. media_dir=/media/somnambulist/Ghost In You # This option can be specified more than once if you want multiple directories # scanned. # # If you want to restrict a media_dir to a specific content type, you can # prepend the directory name with a letter representing the type (A, P or V), # followed by a comma, as so: # * "A" for audio (eg. media_dir=A,/var/lib/minidlna/music) # * "P" for pictures (eg. media_dir=P,/var/lib/minidlna/pictures) # * "V" for video (eg. media_dir=V,/var/lib/minidlna/videos) # # WARNING: After changing this option, you need to rebuild the database. Either # run minidlna with the '-R' option, or delete the 'files.db' file # from the db_dir directory (see below). # On Debian, you can run, as root, 'service minidlna force-reload' instead. #media_dir=/var/lib/minidlna media_dir=V,/media/somnambulist/Ghost In You/Movies media_dir=V,/media/somnambulist/Ghost In You/TV media_dir=P,/home/somnambulist/Pictures # Path to the directory that should hold the database and album art cache. db_dir=/home/somnambulist/serverart # Path to the directory that should hold the log file. log_dir=/home/somnambulist/serverlog # Minimum level of importance of messages to be logged. # Must be one of "off", "fatal", "error", "warn", "info" or "debug". # "off" turns of logging entirely, "fatal" is the highest level of importance # and "debug" the lowest. #log_level=warn # Use a different container as the root of the directory tree presented to # clients. The possible values are: # * "." - standard container # * "B" - "Browse Directory" # * "M" - "Music" # * "P" - "Pictures" # * "V" - "Video" # if you specify "B" and client device is audio-only then "Music/Folders" will be used as root root_container=B # Network interface(s) to bind to (e.g. eth0), comma delimited. #network_interface= # IPv4 address to listen on (e.g. 192.0.2.1). #listening_ip= # Port number for HTTP traffic (descriptions, SOAP, media transfer). port=8200 # URL presented to clients. # The default is the IP address of the server on port 80. #presentation_url=http://example.com:80 # Name that the DLNA server presents to clients. friendly_name=Somnambulist Media Server # Serial number the server reports to clients. serial=12345678 # Model name the server reports to clients. #model_name=Windows Media Connect compatible (MiniDLNA) # Model number the server reports to clients. model_number=1 # Automatic discovery of new files in the media_dir directory. #inotify=yes # List of file names to look for when searching for album art. Names should be # delimited with a forward slash ("/"). album_art_names=Cover.jpg/cover.jpg/AlbumArtSmall.jpg/albumartsmall.jpg/AlbumArt.jpg/albumart.jpg/Album.jpg/album.jpg/Folder.jpg/folder.jpg/Thumb.jpg/thumb.jpg # Strictly adhere to DLNA standards. # This allows server-side downscaling of very large JPEG images, which may # decrease JPEG serving performance on (at least) Sony DLNA products. #strict_dlna=no # Support for streaming .jpg and .mp3 files to a TiVo supporting HMO. #enable_tivo=no # Notify interval, in seconds. #notify_interval=895 # Path to the MiniSSDPd socket, for MiniSSDPd support. #minissdpdsocket=/run/minissdpd.sock` And here's the error I get in terminal when I run: sudo service minidlna restart sudo service minidlna force-reload Force restart error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] Force-reload error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] rm: cannot remove ‘/home/somnambulist/serverart/files.db’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Slumdog Millionaire/Slumdog.Millionaire.Cover.jpg’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Zack and Miri Make a Porno/ZackAndMiriMakeAPornoCover.jpg’: Permission denied [2013/08/12 21:19:46] minidlna.c:744: warn: Failed to clean old file cache. [ OK ] I've spent hours on this at this point, read through various files - and even had a friend who is relatively Ubuntu-savvy try to help me via chat - no such luck. Thanks in advance for any help.

    Read the article

  • repair broken packages-"dpkg: error: conflicting actions -f (--field) and -r (--remove)"

    - by yinon
    Ubuntu 12.04 LTS. if more information will be needed, tell me and'll give. the main problem is: tzach@tzach-pc:~$ sudo apt-get install docky [sudo] password for tzach: Reading package lists... Done Building dependency tree Reading state information... Done docky is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: ca-certificates-java : Depends: openjdk-6-jre-headless (>= 6b16-1.6.1-2) but it is not going to be installed or java6-runtime-headless openjdk-7-jre-lib : Depends: openjdk-7-jre-headless (>= 7~b130~pre0) but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). tzach@tzach-pc:~$ and also: tzach@tzach-pc:~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. **The following packages have unmet dependencies: ca-certificates-java : Depends: openjdk-6-jre-headless (>= 6b16-1.6.1-2) but it is not installed or java6-runtime-headless openjdk-7-jre-lib : Depends: openjdk-7-jre-headless (>= 7~b130~pre0) but it is not installed E: Unmet dependencies. Try using ******* so we tryied the guide here in messege #9: http://ubuntuforums.org/showthread.php?t=947124 we run all the first 4 commands and the last one-"sudo apt-get autoremove" gave us: tzach@tzach-pc:~$ sudo apt-get autoremove Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: **ca-certificates-java** : Depends: openjdk-6-jre-headless (>= 6b16-1.6.1-2) but it is not installed or java6-runtime-headless **openjdk-7-jre-lib** : Depends: openjdk-7-jre-headless (>= 7~b130~pre0) but it is not installed E: Unmet dependencies. Try using -f. so we run the last command twice: sudo dpkg --remove -force --force-remove-reinstreq ca-certificates-java and sudo dpkg --remove -force --force-remove-reinstreq openjdk-7-jre-lib but both of them gives: tzach@tzach-pc:~$ sudo dpkg --remove -force --force-remove-reinstreq ca-certificates-java [sudo] password for tzach: dpkg: error: conflicting actions -f (--field) and -r (--remove) Type dpkg --help for help about installing and deinstalling packages [*]; Use `dselect' or `aptitude' for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through `less' or `more' ! EDIT FOR green7-output of "sudo apt-get -f install": tzach@tzach-pc:~$ sudo apt-get -f install [sudo] password for tzach: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: icedtea-7-jre-cacao icedtea-7-jre-jamvm java-common openjdk-7-jre-headless tzdata-java Suggested packages: default-jre equivs sun-java6-fonts ttf-dejavu-extra fonts-ipafont-gothic fonts-ipafont-mincho ttf-telugu-fonts ttf-oriya-fonts ttf-kannada-fonts ttf-bengali-fonts The following packages will be REMOVED: ttf-mscorefonts-installer The following NEW packages will be installed: icedtea-7-jre-cacao icedtea-7-jre-jamvm java-common openjdk-7-jre-headless tzdata-java 0 upgraded, 5 newly installed, 1 to remove and 355 not upgraded. 5 not fully installed or removed. Need to get 0 B/29.6 MB of archives. After this operation, 88.5 MB of additional disk space will be used. Do you want to continue [Y/n]? y debconf: DbDriver "config": /var/cache/debconf/config.dat is locked by another process: Resource temporarily unavailable dpkg: warning: there's no installed package matching ttf-mscorefonts-installer:amd64 Setting up tzdata (2012e-0ubuntu0.12.04) ... debconf: DbDriver "config": /var/cache/debconf/config.dat is locked by another process: Resource temporarily unavailable dpkg: error processing tzdata (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: tzdata E: Sub-process /usr/bin/dpkg returned an error code (1) EDIT2 FOR green7: tzach@tzach-pc:~$ sudo apt-get remove --purge tzdata [sudo] password for tzach: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: ca-certificates-java : Depends: openjdk-6-jre-headless (>= 6b16-1.6.1-2) but it is not going to be installed or java6-runtime-headless libc6 : Depends: tzdata but it is not going to be installed libc6:i386 : Depends: tzdata:i386 libical0 : Depends: tzdata but it is not going to be installed openjdk-7-jre-lib : Depends: openjdk-7-jre-headless (>= 7~b130~pre0) but it is not going to be installed python-dateutil : Depends: tzdata but it is not going to be installed ubuntu-minimal : Depends: tzdata but it is not going to be installed util-linux : Depends: tzdata (>= 2006c-2) but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). EDIT3 FOR green7: tzach@tzach-pc:~$ sudo apt-get install openjdk-7-jre-headless [sudo] password for tzach: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: openjdk-7-jre-headless : Depends: tzdata-java but it is not going to be installed Depends: java-common (>= 0.28) but it is not going to be installed Recommends: icedtea-7-jre-cacao (= 7~u3-2.1.1~pre1-1ubuntu3) but it is not going to be installed Recommends: icedtea-7-jre-jamvm (= 7~u3-2.1.1~pre1-1ubuntu3) but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). some things in the text also supposed to be bolded. but not critic (: Thanks for the editing! Thanks a lot for your assistance.

    Read the article

< Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >