Search Results

Search found 7843 results on 314 pages for 'power over ethernet'.

Page 37/314 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >

• Modify actions when battery is critically low?

  - by Bjarke Freund-Hansen

  I am running ubuntu (not xubuntu!) and am using xfce4 on my laptop. When my laptop battery is critically low, ubuntu/xfce4 performs some action (perhaps hibernate?) which causes my laptop to shut down. However when I start it again, it never comes up. I don't even get BIOS or anything on the screen, it is completely black. The only way to get it back up is to take it apart, remove the internal cmos battery as well as the main battery, wait a few minutes, and put it back together. Obeviously this is not optimal. How do I disable all actions when the battery is critically low? I would rather have it run out of power, than ending up in this error condition. Thanks in advance. :)

  Read the article

• suspend not working

  - by Eric

  I am running 13.10 on an ASUS 101-SE netbook. Under "power settings" I have selected suspend when inactive for 10 minutes and suspend when lid is closed. I get a warning when inactive that the computer will suspend due to inactivity, but it does not suspend either from that condition or when closing the lid. I seem to be getting multiple suspend messages as I need to click "cancel" or "OK" many times to get the error window to close when it has been inactive for some time. Anyone have any tips? Thank you.

  Read the article

• Laptop resumes from suspend while lid is closed

  - by Gus

  I have a Dell Studio 15 and I am running Ubuntu 10.10. When I close my lid or select the suspend option, the machine suspends as indicated by the slowly pulsing power indicator. I'll put the machine in my bag and after a while it seems that the machine resumes, at least I think. When ever I go to get it, it's overheated and the system cannot resume. I am guessing that the processor resets in this overheat condition, but heat is still generated. This has happened about three times and I'm getting worried that I'll end up damaging the machine. How can I diagnose why the system is resuming from suspend? Can I force it to never resume from suspend if the lid is down?

  Read the article

• How do I prevent an external monitor from shutting off when closing my laptop lid?

  - by Thom

  I've seen this issue on previous versions of Ubuntu, but not on 12.04 and some of those are resolved bugs, so I'm asking again. I've set up power management so that, when plugged in, my laptop does nothing when the lid is closed. I do this so that I can use as a desktop with my external monitor with the screen closed and the laptop scurried away from my desktop. I tried turning off the laptop monitor to see if that made a difference, but it doesn't. The problem is that closing the lid still shuts off my external monitor. What can I do to prevent this?

  Read the article

• How to close lid without triggering standby one time only

  - by Ian Mackinnon

  Related: How can I tell Ubuntu to do nothing when I close my laptop lid? I have my laptop set to activate standby when I close the lid. I want to keep this as the default for both battery and AC power. But occasionally I want to close the lid without triggering standby (eg. while just listening to audio). Is there someway I can tell Ubuntu, "I'm going to close the lid now. Don't stand by this time", without altering the defaults (because I almost always forget to change them back).

  Read the article

• Ubuntu reports low battery capacity on my Dell Vostro

  - by Jeff

  I have a Dell Vostro 1500. Before I wiped Windows XP off my hard drive in 2009, I had a full ~7 hrs battery capacity. I installed Ubuntu 9, and the capacity immediately dropped to about 27% (and has since decreased to about 11%). I couldn't figure out what to do, so I've just lived with the 20-30 minute battery life ever since. I upgraded to Ubuntu 10, and the issue remained. I wiped my hard drive clean again and installed Ubuntu 11, and the issue still remains. I tried what they told me in the forum here, but it didn't do anything. Is it possible for a battery to suddenly lose most of its capacity?? Or is there a bug in the power management software?

  Read the article

• CPU frequancy stuck at 1.20 GHz using TLP?

  - by Rana Muhammad Waqas

  I have installed TLP for power optimization on Ubuntu 13.10. Instructions I start computer its running fine I can change the CPU frequencies to whatever I want, but after some time it stuck on minimum frequency 1.20 GHz, I cant change that to anything else. I have tried to stop it by using sudo tlp stop but it doesn't stop. Tried even to kill its process sudo killall tlp but it seems they have a different name of process of that so i am not sure what to do now. I reported to the linrunner but cant seem to find a solution

  Read the article

• Energy saving with two batteries (Gigabyte S1080 and similar)

  - by user37155

  my today question is: how do I manage a tablet (Gigabyte 1080) with an additional battery in Ubuntu ? The control bar shows two separate batteries but starts to suck all the energy from the secundary battery, not leaving any power in it and ruining it (if I don't remove it earlier), and then starts with the primary battery. Here you find a description of the secundary battery: http://www.gigabyte.com/products/product-page.aspx?pid=3837#kf Do you have some solutions for a more confortable use of te device, with windows-like drivers maybe ? Is there a graphical tool to manage two batteries in Linux, in order not to ruin them, and possibly to save energy with them ? Many thanks and greetings, Francesco

  Read the article

• How Is My Computer Able to Restart Itself?

  - by Jason Fitzpatrick

  It’s such a common place activity that most of us have likely never stopped to even think about it: the automatic restart. Whether user or application-initiated, what exactly happens when your computer cycles its own power? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-drive grouping of Q&A web sites. How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

  Read the article

• Is it save to configure "Shutdown" on "When laptop lid is closed" ?

  - by Takkat

  To setup a laptop owned by a complete PC novice any settings that may become hard to tackle remotely need to be avoided. The laptop will be administrated via SSH. One thing in my list are problems arising from improper wake-ups from suspend or hibernate as they may also affect network accessibility. This is why I thought setting up power management to "shutdown" on closing the laptop lid could be a good idea. However I am not sure if this is a safe way to do. What problems in addition to software not closing properly (and thus not saving their data) could I be faced if I proceeded as planned?

  Read the article

• Is it safe to configure "Shutdown" on "When laptop lid is closed" ?

  - by Takkat

  To setup a laptop owned by a complete PC novice any settings that may become hard to tackle remotely need to be avoided. The laptop will be administrated via SSH. One thing in my list are problems arising from improper wake-ups from suspend or hibernate as they may also affect network accessibility. This is why I thought setting up power management to "shutdown" on closing the laptop lid could be a good idea. However I am not sure if this is a safe way to do. What problems in addition to software not closing properly (and thus not saving their data) could I be faced if I proceeded as planned?

  Read the article

• Xubuntu fails to stay awake when the machine is under load

  - by Alex

  I have the following problem with a fresh install of Xubuntu 12.04: I set up power management options so as to send the machine to sleep after it's been idle for a while. My intention was to have it finish some lengthy numbercrunching and then fall asleep late at night when nobody's present to shut it down. What actually happened, however, is that the machine goes to sleep whenever the desktop session has been idle for the specified amount of time, and it does not seem to care at all about CPU load, and I had to disable sleep altogether. Is there any way to fix this?

  Read the article

• My Laptop Battery Does Not Charge

  - by Oo Nwoye

  I am using a HP Pavilion and Ubuntu 11.10. I have been using Ubuntu for about a year. Recently (in Nov or there about), I noticed my battery never charges fully no matter how long it has been plugged in. I thought it was a problem with the power pack. However, after changing it, the problem is still persisting. I upgraded to 11.10 form 11.04 at about the same time so I do not know if this is a software or hardware issue. How do I solve this? This problem has been written about in various forms Laptop battery not charging after update?. Please help me or find someone that can.

  Read the article

• Battery life decreased after upgrade to 11.04

  - by bruno077

  After upgrading from Ubuntu 10.10, my battery life has decreased dramatically. There was a bug in Ubuntu 10.10 where the Load Balancing Tick and Kworker would interrupt and wake-up the cpu too much, and this wasn't normal. I applied a gnome-power-manager fix back then, following this question, which leads to this bug report, and battery life increased to 3.5 hours. I'm getting around two hours of battery-life in Natty, and calling Intel's powertop reveals that this bug is back. Is there a fix for Natty yet? I have a Core 2 Duo ULV, Thinkpad Edge 13

  Read the article

• suspend error on 14.04 LTS

  - by user1450663

  I've looked around and seems like various problems around suspend are wide spreaded for 14.04 release, nevertheless I haven't seen exactly my problem reported, nor my laptop model mentioned. So, the problem. When I press sleep button system seems to be going into suspend, i.e. screen goes black, it stops responding on the keyboard and wireless LEDs turn off, however the power LED doesn't go into suspend state and CPU fan also keeps spinning. But unlike the other problem described here https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1315435 when I close the lid and reopen it - system wakes up and goes back to normal locked screen state, so reboot is not needed. System details: This is a clean freshly installed Ubuntu 14.04, 32bit Laptop Dell D630 kernel 3.13.0-34-generic

  Read the article

• Limiting what resumes computer from suspend

  - by user1399195

  I'm having a ton of trouble getting Suspend to work with my laptop. I want to start using Ubuntu but this is a pretty important aspect since I take my laptop with me everywhere. Anyways, I wanted to narrow down the possible problem with my laptop. What happens is that when I suspend my computer, within seconds, it just boots back up. I have changed /proc/acpi/wakeup to where everything is disabled but that did nothing. Is there a way where I can disable every feature from waking up the laptop except the power button?

  Read the article

• Linksys WAP54G v3.1 no access, power and link LED solid

  - by user142113

  I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Anyone love/hate the PowerConnect line of switches from Dell?

  - by Rob Bergin

  I am looking at replacing some unmanaged 16 port store bought GB switches and wanted to go with Cisco but it may be cost prohibitive. Instead I am looking at ProCurve or Dell's PowerConnect line up. I am looking for SNMP, Management, VLANs, and SFLOW would icing on the switch cupcake. I would get the 6224 or the 6248 and then maybe add the RPS-600 to it for redundant power. I think the RPS-600 supports multiple switches. Rackspace is also a little challenge so I am trying to do it with as little Rack Units as possible. Ideally I would go with two 6224's or a single 6248 and then do two VLANs. Thanks for any feedback. Rob

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Hi, Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Failed to bring up eth1 in a dual ips solution in ubuntu

  - by lxyu

  I'm using ubuntu 12.04. I tried to assign two ips to two ethernet cards in my server. The content of /etc/network/interfaces is like this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 114.80.156.a netmask 255.255.255.224 gateway 114.80.156.b auto eth1 iface eth1 inet static address 114.80.156.c netmask 255.255.255.240 gateway 114.80.156.d a b c d have different values, which means the two ips are in different vlans. But I can only bring up eth0 with this command: $ /etc/init.d/networking restart RTNETLINK answers: File exists Failed to bring up eth1. ...done. I have checked the question here which shows the same problem like the one I encountered: Can only bring up one of two interfaces But it seems it's not really solved. And in my situation, I need the 2 ips to use 2 different gateways. So how to fix this problem? Edit1, changed the example config ip from 192.168.0.0/16 subnet to another 'real' subnet. Edit2, the purpose of doing this is fairly simple. Because the ip range I previous in don't have more room for new servers, and I have to move to another ip range. So I want to make the public servers bind to 2 ips for the transition period. I only have really limited knowledge about routing and subnet. @BillThor @rackandboneman, would you please give me some keywords or links on how to setup route for 2 ips? and @Mike Pennington, how do you know I speak chinese?

  Read the article

• Can't connect two PCs to a Network Switch at the same time (Windows 7)

  - by puk

  I have two computers connected to a network switch and every once in a while one of the computers will lose its internet connection. It's almost always the same computer every time. However, if I play around with the control panel, I can switch it, so that now the other computer is not connected. Restarting either of the computers does not help either. In Windows, the worlds-greatest-trouble-shooter tells me that a network cable is unplugged and that I should try plugging it in...Disabling and re-enabling my NIC does not fix this problem, neither does swapping cables around. When rebooting, the BIOS complains about how the Ethernet Cable is not plugged in. If it's in any way important, My set up at the office is like so: Modem - Routher - Network Switch 1 - Network Switch 2. I have tried turning off the energy saving option for my NIC, and I tried manually setting the link-speed to 100Mbps Full Duplex without any luck. Also, I have a Realtek PCIe GBE Family controller on both computers Does anyone have any idea why this is happening every 5-10 days? EDIT: I have also tried using a completely different Network Switch and the problem still persists as before.

  Read the article

• ProCurve network expansion

  - by Blue Warrior NFB

  I've hit a bit of a wall with our network scale-out. As it stands right now: We have five ProCurve 2910al switches connected as above, but with 10GbE connections (two CX4, two fiber). This fully populates the central switch above, there will be no more 10GbE Ethernet connections from that device. This group of switches is not stacked (no stack directive). Sometime in the next two or three months I'll need to add a sixth, and I'm not sure how deep of a hole I'm in. Ideally I'd replace the core switch with something more capable and has more 10GbE ports. However, that's a major outage and that requires special scheduling. The two edge switches connected via fiber have dual-port 10GbE cards in them, so I could physically put another switch on the far end of one of those. I don't know how much of a good or bad idea that would be though. Is that too many segments between end-points? Some config-excerpts: Running configuration: ; J9147A Configuration Editor; Created on release #W.14.49 hostname "REDACTED-SW01" time timezone 120 module 1 type J9147A module 2 type J9008A module 3 type J9149A no stack trunk B1 Trk3 Trunk trunk B2 Trk4 Trunk trunk A1 Trk11 Trunk trunk A2 Trk12 Trunk vlan 15 name "VM-MGMT" untagged Trk2,Trk5,Trk7 ip helper-address 10.1.10.4 ip address 10.1.11.1 255.255.255.0 tagged 37-40,Trk3-Trk4,Trk11-Trk12 jumbo ip proxy-arp exit

  Read the article

• Internet slowed down because of SQUID Server setup

  - by Ranjith Kumar

  Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

  Read the article

• Gigabit LAN not working on ASUS M2N-MX

  - by chmod

  Today I replace my FastEthernet switch with a newly bought gigabit switch (DGS-1008A). All computers in my house are displaying that the connection speed is 1 Gbps except for one. The computer that is not working is an ASUS M2N-MX which contain an onboard gigabit NIC. See ASUS link for confirmation http://www.asus.com/Motherboards/AMD_AM2/M2NMX/ Here are some info of the machine OS: Windows 7 Ultimate SP1 64bit BIOS version: 1004 (latest) Driver: installed via Windows update (latest from Windows update) Windows Update: fully updated The machine is reformatted 3 days ago, so it's pretty clean, no junk, no virus, etc Cable: Amp CAT5E 5 meters In device manager, the name of the NIC is "NVIDIA nForce 10/100/1000 Mbps Ethernet" What I have try: I did try to install the driver provided in ASUS website, but there isn't any for Windows 7 64 or Vista 64. I did try to install the latest nForce340/6100, downloaded from Nvidia website. However, the LAN driver refuse to install, it complain that I already have the best driver installed. I looking in the property -- advance tab -- Speed/duplex settings, in an attempt to force it to run at 1000Mbps, but there is no 1000Mbps choice, only 10 and 100Mpbs. I change the CAT5E cable (use one from another computer that is running gigabit without problem) Anyone have this issue or know how to solve it? Thanks

  Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >