Search Results

Search found 1072 results on 43 pages for 'rubber boots'.

Page 37/43 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

• Grub hangs at "Starting up ..." when USB flash card reader is plugged in (on Ubuntu Hardy)

  - by Laurence Gonsalves

  I have a PC with Ubuntu Hardy installed. The machine boots fine unless my USB flash card reader (one of those N-in-1 readers by MediaGear) is plugged in at startup. If the reader is plugged in, the boot process proceeds as normal until it gets to the screen that says "Starting up ...". At that point it just hangs forever. To work around this I currently leave the reader unplugged when booting, and then plug it back in after I see that Ubuntu is actually starting. This is annoying though, especially when I reboot the machine (typically for updates), forget to unplug the reader, and walk away only to come back hours later to find the machine hung. My guess is that the presence of the reader is confusing Grub about where to find the kernel. The weird thing is that Grub is on the same drive as the kernel I want it to boot so clearly the drive is still readable even when the flash card reader is plugged in. Is there some way I can tell Grub to never go looking on the flash card reader?

  Read the article

• Computer hangs at boot screen with new RAID card

  - by shanethehat

  I am trying to build a new server around a Biostar TH61 motherboard and an Adaptec 6405E RAID controller card. The machine booted fine from USB before the RAID card and drives were installed. After installing, on the first boot the card was detected, but then started to spit out the following message every 10 seconds: Error: Controller Kernel Stopped Running << Press any key to continue ... Following the troubleshooting guide I unplugged everything, reseated the card, and reattached all the drives. This time the machine is sitting on the boot screen without any error messages and flashing a cursor, but after 15 minutes of this, nothing seems to be happening. Given that there are no error messages I'm hesitant to reboot again. Is it normal for a RAID card to sit without a status message when it firsts boots, maybe to initialise the drives or something? The current screen output looks a bit like this: Controller #00 found at PCI Slot:01, Bus:01, Dev:00, Func:00 Controller Model: Adaptec 6405E Firmware Version: 5.2-0[18512] Memory Size: 128MB Serial number: 111111111111111 SAS WWN: 50000D1104AE9180 _ Update: So after waiting 30 minutes I've rebooted back to the Kernal Stopped Running error. Maybe time to update the RAID BIOS.

  Read the article

• Installing Windows 7 from USB on a Thinkpad T61

  - by Halik

  I am trying to install Windows 7 Professional from USB 3.0 flashdrive, on a Thinkpad T61. The problem is, Thinkpads BIOS will not detect the flash drive as bootable medium, and won't allow to boot from it. What I did: Enabled USB BIOS Support in BIOS (it was on by default) In startup menu, added USB HDD to boot order (it has '-' sign in front of it) Created Windows 7 install media with UNetbootin, WinUSB (linux tool) dd and Grub4DOS. As you can tell, currently, I only have access to Linux machine to make the flashdrive. What happens: The T61 BIOS shows '-USB HDD' in boot order menu. The '-' sign suggests that the plugged flash drive is currently not bootable. The same flashdrive (with the same Windows image on it) is booting without any problems on a Dell D430 and Lenovo Y550. Also, Ubuntu 12.04 install USB created with Unetbootin shows as bootable ('+' sign in BIOS boot order menu) and boots from the F12 boot menu. Additional info thinkwiki.org says that some Thinkpad BIOSes do not use MBR on flashdrives. It suggests using Extended-IPL boot loader, but the provided links are broken and there seems to be no mirrors. Solution: http://superuser.com/a/430186/54970

  Read the article

• Is it possible to boot Windows 7 from when you're harddrive's partition with two OSes?

  - by Muhammad

  I have a PC with a hard drive that's partition into home directories for Windows 7 and Ubuntu. I primarily use Windows 7 and occasionally (once a week) use Ubuntu. When I boot up my computer, I usually get taken to a boot menu that includes about 5 different options: 3 are for Ubuntu's configurations, one's for swap, and the forth is for Windows 7. Then after I select Windows 7 or Ubuntu from this menu, I get taken to another menu that again asks me for Windows 7 or Ubuntu. This time, there's only 2 options, Windows 7 and Ubuntu. [Side note: out of experience I realized most boot menus are timed and so are these.] So if I ever turn my computer on without actually sitting in front of it for a few minutes, it boots into Ubuntu. I'm trying to figure out what I need to do so I can first get rid of the 2 boot menus. And if possible, I'm looking for help changing my boot options where I can load up Windows 7 (even with the boot menu wait of about 30 seconds). My harddrive's partition's laid out like this: Windows 7 (C partition) Multimedia (D partition, I just use this for backup/non-OS stuff) Ubuntu (home directory) Swap Is there any other information I need to provide?

  Read the article

• LVM and cloning HDs

  - by jcea

  Using Linux, I have several backup levels. One of them is a periodical sector by sector copy (using dd) of my laptop harddisk to an external USB disk. Yes, I have other backups too, like remote rsync. This approach (the disk dd) is OK when cloning a HDD with no LVM volumes, since I can plug the external disk anytime and mount the partitions simply mounting /dev/sdb* instead of /dev/sda*. Trivial and handy. Today I moved ALL my harddisk (including the /boot) to LVM. Everything works fine. I will stress it for a couple of days, and then I will do a sector by sector copy to my external harddisk. Now I have a problem, I guess. If in the future I plug the external USB HDD to recover any file, the OS will detect a duplicate LVM configuration, with the same name and the same UUID. Even doing a vgrename (which LVM would be renamed, the internal HDD or the external HDD?), the cloned UUID will not change. Is there any command to change name and UUID? Ideally I would clone the HDD and then change the LVM group name and its UUID, but I don't know how to do it. Another related issue would be... In the past I have booted my laptop using the external disk, using the BIOS boot menu and changing GRUB entries manually to boot from /dev/sdb instead of /dev/sda. But now my current GRUB configuration boots directly from a LVM logical volume, something like: set root='(LVM-root)' in my grub.cfg. So... What is going to happen with duplicated volumes? Any suggestion? I guess I could repartition my external harddisk and change backup strategy from dd to rsync, but this disk has windows installed too, and I really would like to have a physical "real" copy.

  Read the article

• Managing per-user rc.d init scripts

  - by Steve Schnepp

  I want to delegate SysV init scripts to each user. Like the SysV init, each item in ${HOME}/rc.d starting with S will be launched on server start-up with the start argument. The same for the server shut-down with the one starting with K and with the stop argument. I thought about scripting it myself, but maybe there is already some kind of implementation out there1. In summary it would be a script in /etc/init.d/ that iterates through all the users and launches runparts as the user on the relevant scripts. The platform here is a Linux (Debian flavour), but I think the solution would be quite portable among various Unix-like platforms. Update: The point here is for users to be able to create their own init scripts that should be launch on their behalf when the system boots up. As Dan Carley pointed out, the services won't be able to access any system asset (priviledged ports, system logs, ...). 1. This way I don't have to think that much about all the subtle security implications such as script timeouts for example...

  Read the article

• Windows memory logged on vs logged off

  - by Adi

  Let's say I power on my fresh installed Windows 7 x64 machine. After Windows boots up, there are a bunch of services being started in the background that start allocating memory. Then I enter my user/pass and Windows logs me in. Let's supose I don't do anythig else (I don't explicitely start any application) and I don't have any other app installed by me. So it's fresh install of my machine. My question is: how much memory is needed for all the UI & other stuff? Is it a good indicator to look into task manager and check all the processes started under my user name and sum up all the memory consumed by those processes to get the total amount of memory I am consuming just to stay logged on? Basically this is my question: how much memory is needed just to stay logged on? Now, if log off would all the memory be released back to the system so that the background services can benefit of? Also, I assume that there might be a different discussion for each Windows flavors (?)

  Read the article

• Access Existing Linux Installation from Windows Bootloader - Linux Installed and Then Windows 7

  - by nicorellius

  My hard drive is failing. I installed a new drive, and the installed Ubuntu 12.04 to try to rescue data. Realized that I wanted to install Windows and just access drives without transferring data (there are loads of it). I then installed Windows 7. Now my drive only boots to Windows 7. How do I access Linux and make Windows boot-loader load Linux? I originally thought I would just not use the Ubuntu installation but now I think I want it to be a dual boot system. What are good boot-loaders to install for this kind of dual boot situation? Can I accomplish this with BCDEdit? If I would have done this the other way (Windows first, then Linux) everything would be fine, but I didn't and now I'm trying to fix this. The problem I have is that I don't really know how to boot into Linux to retrieve any files I need. I guess using the disc would work, but I'm not sure how to go about this.

  Read the article

• Only half of RAM is recognized by BIOS

  - by Rick Crawford

  I got a Gigabyte GA-P35-DS3 mainboard. Some time ago I noticed that Windows only showed 2GB instead of 4GB. I don't know exactly what caused it anyway. I tried putting in each of the 4 x 1GB RAM modules one by one, and tried every slot one by one, until every stick and slot worked. However, then I tried adding one more at a time, and it kept showing 1GB, until I put in all 4, where it only showed 2 GB instead of 4 (in BIOS and windows 7 64bit). I tried replacing the BIOS battery since I've read that low battery could cause it. It didn't help though. I also bought 4GB new RAM (yes, it's supported, I checked it), and it's still the same, it only shows 2GB (or 3GB, when I put in 4 of the new and 2 of the old). I also did the latest BIOS update, and used default BIOS settings, but nothing of that helped. When my PC boots it shows "RAM modules used 2 and 3", when 4 sticks are in - or "0 and 1", when only 2 are in.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

  Read the article

• Ubuntu won't boot from USB memory stick

  - by mackenir

  I used the instructions on this webpage to create a bootable USB drive for running Ubuntu 9.10. Unfortunately it doesn't work on my EeePC. Even with 'Removable Dev.' selected in the BIOS as the first boot device, the PC just boots into Windows 7. How do I troubleshoot this problem? The drive is readable and looks like this: Directory of E:\ 28/10/2009 21:14 <DIR> .disk 28/10/2009 21:14 222 README.diskdefines 28/10/2009 21:14 143 autorun.inf 28/10/2009 21:14 <DIR> casper 28/10/2009 21:14 <DIR> dists 28/10/2009 21:14 <DIR> install 28/10/2009 21:14 <DIR> syslinux 28/10/2009 21:14 4,098 md5sum.txt 28/10/2009 21:14 <DIR> pics 28/10/2009 21:14 <DIR> pool 28/10/2009 21:14 <DIR> preseed 28/10/2009 21:14 0 ubuntu 26/10/2009 16:16 1,468,640 wubi.exe 25/02/2010 00:28 2,147,483,648 casper-rw 8 Dir(s) 5,290,307,584 bytes free

  Read the article

• Piecing together low-powered hardware for an RS-232 terminal server

  - by Fred

  I'm working on reconstructing my Cisco lab for training/educational purposes and I found that the actual terminal server I have is dead. I have a couple of 8-port PCI serial cards which would be more than ample for my lab, but I don't want to leave my personal computer running to be able to access the console ports. Ideally I would access the terminal server remotely, either by SSH/RDP to the box (depending on what OS I go with) or by installing a software package that allows me to telnet directly to a serial port. I know I've found a program that does this under Linux in the past but its name escapes me at the moment. I'm thinking about scavenging for some old hardware, on eBay or something, to put together a low-powered PC. Needs to be something that: Has Low-power consumption Has at least 2 PCI slots (though I certainly wouldn't complain about having more) Has onboard Ethernet (or, if not, another PCI or ISA slot (not shared)) Can be headless once an OS installed (probably Linux) I'm currently leaning towards an old fashioned Pentium (sub-133MHz era) but I am wondering if anybody else knows of another platform/mobo that would suit these needs. Alternatively, I've been considering buying a Raspberry Pi and a big USB hub along with a bunch of USB-Serial adapters but this sounds like it'd get messy quick with cables and adapters all over the place, and I may not even have the same ttyS#'s between boots.

  Read the article

• Cloning a NAS drive which hosts a SQL Server DB

  - by Adrian Hand

  We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

  Read the article

• Supermicro X8SIL-F with Enermax Modu82+ 625W PSU booting issue

  - by Richard Whitman

  I am assembling a custom PC. The configuration is below: Motherboard: Supermicro X8SIL-F Processor: Intel Xeon 3430 Power Supply: Enermax Modu82+ 625W. Memory: Kingston KVR1333D3LQ8R9S/8GEC 8GBx1 installed in DimmA1 This power switch: Frozen CPU switch When I turn on the PSU, the motherboard tries to start itself before I even push the power switch. The following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and this time it rotates for about 3-4 seconds before stopping. If I pull out the Power switch, and turn on the PSU, again the MB turns on itself and the following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and the system boots properly I am sure there is nothing wrong with any of the components, because I have two sets of identical components (2 MBs, 2 CPUs, 2 PSUs, 2 switches and so on). And both of the systems show the same symptoms. Why is the MB booting up by itself? Why does it fail to boot when the Power Switch is installed? Is something wrong with the type of Power Switch I am using? PS: the power switch is installed correctly, I have double checked the MB manual to make sure its connecting the right pins.

  Read the article

• hp DL380 G4 won't boot with disk plugged into front USB

  - by Kev

  We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the BIOS (which is current, BTW) and never boot, even though the USB disks are not "bootable" per se. Our old drives did not exhibit this behaviour (so I don't think it's this type of issue that I've read about other servers.) The old drives were USB 2.0, but this shouldn't make a difference, AFAICT--the specs say all of the G4's USB ports are the same, 2.0, anyway, so I'm not sure how one port would handle a USB 3.0 device better than another. If we plug the new drives in one of the back slots, it boots fine. What's the cause? My concern is that the front USB port, and possibly the motherboard, might be starting to die. (We are experiencing other strange issues with them, or were initially, like intermittent file permissions errors despite wide-open ACL on these local drives, but some serverfault users have me convinced they may be coincidental software/security related issues.)

  Read the article

• Windows 7 won't boot from any bootloader except for Windows Boot Manager after partition resize

  - by user2468327

  I have a triple boot system on a single SSD: OSX, Windows 7, and Ubuntu. I use Chimera (basically another version of Chameleon) as my bootloader. Usually I can boot all 3 OSs without any issue, but after using GParted to make my Ubuntu partition 2 Gigs larger, Windows 7 throws me an error when trying to boot to it from either Chimera or Grub. The error is consistently: `0xc000000e can't find \Boot\BCD" (slightly paraphrased). However, I can still get into Windows by selecting Windows Boot Manager from the boot options in my BIOS. I've already tried several known fixes for similar issues, including bootrec /rebuildbcd (and variations), and BootRec.exe/fixMBR + BootRec.exe/fixBoot. I've also tried Chkdsk. At best this has made it so Windows 7 boots on its own by default (making me have to reinstall Chimera and change back my boot settings in the BIOS). At worst this made it so Windows won't boot period. Now I'm back full circle where I started. A detail that might be useful is that bootrec /rebuildbcd says that the number of found Windows installations is 0. I'm fairly certain that I don't have a hybrid MBR. Mainly because I have a UEFI BIOS, and with that, it appears each OS can support a GPT. So it would kind of pointless to have and deal with. I may be wrong though, I couldn't find any way of finding out for sure online. However, I know for sure that the version of Windows I have installed is the UEFI version, as well as every partition tool I've used to look at my boot drive tells me it's GPT. How do I get it back so I can boot Windows 7 through another bootloader so I don't have to manually select it in the BIOS? Preferably without a reinstall.

  Read the article

• Calling Excel from PHP 5 through COM fails on Windows 7 when Apache started through Task Planner

  - by Stefan Pantke

  I currently write an application, which controls Excel through COM: The app creates a COM-based Excel instance, opens some XLS files and reads their contents. Scenario I On Windows 7, I start Apache and mySQL using xmapp-control with system administrator rights. All works as expected. The PHP-based controller script interacts with Excel as expected. Scenario II A problem appears, if I start Apache and mySQL as 'background jobs'. Here is how: I created two jobs using Windows 7 Task Planner. One runs apache_start.bat, the other runs mysql_start.bat. Both tasks run as SYSTEM with elevated privileges when Windows 7 boots. Apache and mySQL work as expected. Specifically, Apache serves HTTP request from clients and PHP is able to talk to mySQL. When I call the PHP controller, which calls and interacts with Excel using COM, I do receive an error. The error seems to come from Excel [not COM itself] and reads like this: Excel can't read the XLS-file Excel failed to save the file due to an ill-name worksheet Interestingly, during the first run of the PHP-based controller script, it takes a few seconds to render the error message. Each subsequent run immediately renders the error message. Windows system logs didn't show a single problem report entry. Note, that the PHP program and the Apache instance didn't change - except the way Apache was started. At least the PHP controller script is perfectly able to read the file-system, since it provides the pathes to the XLS-file through scandir() of a certain directory. Concurrency issues can't be the cause of the problem. A single instance of the specific PHP controller interacts with Excel. Question Could someone provide details, why this happens?

  Read the article

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• ESXi 5 Guests will not boot

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. Note: Investigation eventually determined that problem was with the VMware client on a Lenovo Edge laptop, the only Windows box available in a Linux IT shop. vSphere Client v4 and v5 duplicated behavior on the Lenovo Edge. As indicated in the comment to the accepted answer, replacing the workstation with one using different video was the "fix" for this particular issue. The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. No errors in the Events tab. Switching Guest from BIOS to EFI makes no difference. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspicious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space. Edit 4: Guests copied from my old ESXi 4 server DO NOT boot on the ESXi 5 system. Initially it complains about too little Video RAM being configured for the default 2500x1600, but it still doesn't work properly even after I bump the Video RAM settings or switch it to Auto-Detect.

  Read the article

• Keyboard doesn't function after Fedora 17 update

  - by mickburkejnr

  I updated my Fedora 16 installation to Fedora 17 on Saturday, and the update worked without reporting any errors. I carried on working on the machine in question and then switched the computer off. Last night I went back on the computer, I switched it on and got to the log in screen. At this point I tried to type in my password but the keyboard wouldn't work. I unplugged it (it's a PS/2 keyboard) and plugged it back in. The lights flashed for a split second but the keyboard still wouldn't work. I then plugged the keybaord in to a USB to PS/2 adapter, and the keyboard still wouldn't work. I restarted the computer and tried to access the BIOS and I was able to do so. So the keyboard doesn't seem to be faulty, it just doesn't work when Fedora boots in to the GUI interface. I did try to boot in to the "recovery mode" of Fedora, and the keyboard works here with no problem. As I still have access to Fedora via a terminal interface, is there anything I can do to fix the keyboard problem via the terminal without having to reinstall Fedora?

  Read the article

• Cloned Win7: Keyboard doesn't work

  - by Marc

  I cloned my old Windows7 hard disk to a shiny new Seagate Momentus XT 500GB using the free EaseUs Disk Copy tool on my laptop. After the clone process I used the Windows 7 installation disc to start the automatic startup repair. This took maybe 15 minutes and then my cloned disk was able to start. Now the cloned disk boots until the login screen and then I can't do anything because my keyboard just doesn't work. I tried connecting an external USB keyboard but this didn't help. The mouse is working fine. Note that the keyboard works fine in BIOS and in the Windows startup options menu. I booted into safe mode and again the keyboard is not working at all. I also noticed that the letters "Press CTRL+ALT+Delete to login" are now shown in italic font but they used to be shown non-italic on the original disk. I have now replaced the clone with the original disk again and from here everything works fine. Doesn't anybody have an idea how I can get my keyboard back?

  Read the article

• AMD Phenom II X2 555 BE, core unlock suddenly not working?

  - by user328271

  I've had a Phenom II X2 555 BE for around 2 - 3 years. When I got it, I immediately core unlocked it with my ECS A880GM-A3 mobo, which makes it turn into a Phenom II X4 B55. A few days ago, I installed Windows 7 64 bit to compensate for my 4 gigs of ram. When I start my system with its cores unlocked, it will restart after the BIOS screen. If I disable the core unlock, it boots to OS just fine. My question is: Does 64 bit OS makes a difference in core unlocking? Does my 3rd and 4th core burnt out? Also extra info: I tried core unlocking but keeping the 3rd and 4th core disabled and it still won't boot into OS. Could it be motherboard problems? Sorry for bad English. I will try to give additional information if needed. Thanks! Also it is worth mentioning I'm no computer expert but I tried to make my explanation as short as possible. I also asked my question on TomsHardware, but I had no answer till now so I decided to ask here too. anyone...?

  Read the article

• Dell PowerEdge 860 won't boot but gets power

  - by fierflash

  I have a Dell PowerEdge 860. Got an 2008 R2 running on it. Here is the scenario I'm currently in: I can boot it up and work as usuall. But when I restart it, it just shuts down, doesn't reboot, and it won't boot up again. Then it stays in this "mode", On/off button blinking green(standby mode?) and System Indicator LED blinking amber. If I try to press the On/Off button on the frontpanel it won't boot. It's like you can hear the fan from the PSU running but nothing else is trying to boot. If I unplug the powercable and then put it back in again it's the same, the extremley noisy fans won't start and it's just sitting there. If I let it "rest" for like 1 to 24 hours while the powercable is unplugged and I plug it in again, it boots directly, without me having to push the On/Off button. What I have tried: Run diagnostics(not the one in POST phase) and everything is fine Booting without any cables except the powercable Boot without memory installed Boot without the raidcable plugged in Cleared NVRAM Reseated all the components and cables Googling like a freak for any possible solution Tried Dell Support but I don't have any warranty left so they can't help me unless i pay some ridiculous amount of money I suppos Do anyone have some experience with the same issue? Do I need to replace something or is there any other way to determine the problem? Any help will be greatly appreciated.

  Read the article

• How to clone a HDD and then use the clone with VMware (so that Windows works!)?

  - by Ahmad

  I have a system on which Windows 7 is installed, and I am trying to make a clone of its HDD image, which I then want to use in my main PC with VMware, so that I can boot Windows 7 off the cloned HDD. I used Ultimate Boot CD v5.1.1 with the system whose HDD I wanted to clone, and I cloned it using EaseUs Disk Copy, which comes with Ultimate Boot CD. The source HDD was 250 GB in size which had 3 partitions, while the USB HDD I attached to the system, which was supposed to be the destination/clone HDD, was 320 GB in size. I chose to create an exact replica, and so 250 GB worth of data (partitions, etc.) was copied exactly, and the rest of the space was un-allocated. I now connected this USB HDD to my main PC, fired up VMware Workstation 8 and defined a new Virtual Machine, and chose to boot off the USB HDD. Result is that when Windows is booting (from the cloned HDD inside VMware), I get the blue screen error before I reach the login screen. How can I change my methodology so that Windows even boots from the clone? I can change any tools I use, etc.

  Read the article

• Automated Linux VMs on Hyper-V 2012

  - by Mick

  I have a requirement to create a ton of linux VMs for our customers (we run managed infrastructure) on Hyper-V 2012 in the coming months and I have an issue with automating it. Here is how I need it to work: User accesses their web page and creates a VM. VM is created with a unique IP and name User logs in over SSH I know Hyper-V quite well and can work with powershell and am a C# programmer so the development side of things is taken care of. I also know enough about Linux to be at least competent: I have used it on and off for a number of years but not done anything Enterprise-level with it. All this can be done easily by manual processes but I need to be able to script or program this to automate it as there could be hundreds of them being created but I don't know how. My first thought is to have a database with random-generated names and IPs already created but I don't know how to get a Linux VM to boot up and grab one from the database... I suppose a Kickstart script would take care of it but I don't know what to do from there. Here is what is bouncing around in my head: Create a std linux build. - Easy to do Someone clicks "Create VM" and I pull a name and IP from the database and write it to a kickstart script. - Easy to do I could then open the template VHDX file and copy in the script and then save it. - Not sure if possible User boots up new VM and the kickstart script gives it the name and IP I assigned it. My problem is that I don't know how to open a VHDX file and insert a kickstart script into it... can't figure it out. I am reaching here and this solution may be miles off... I am more used to creating Windows VMs with scripts and so on which i am more familiar with... any help would be appreciated. Thanks Mick

  Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43  | Next Page >