Search Results

Search found 18728 results on 750 pages for 'setup deployment'.

Page 37/750 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >

  • Entering BIOs Setup from Supermicro IPMI KVM

    - by Joshua Lim
    I'm having trouble getting into BIOs Setup from Supermicro IPMI "KVM" - Remote Control Console Redirection. I need to change the boot order to CDROM first. I'm running Windows 2008 server. After some Googling, it says here that the method is to: Press TAB to enter Setup screen. Press Esc twice to take effect. http://www.supermicro.com/support/faqs/faq.cfm?faq=6222 A month ago, I tried that 30-40 times + DEL, over 2 hours, it worked. Now, I've been trying the same key combination for more than an hour, rebooting each time it failed, it still doesn't work. Note: I've only got a notebook computer, no extra monitor.

    Read the article

  • Setup IPsec VPN using ASA5505 behind Juniper SSG5

    - by i_ch3ry
    I have been assigned to establish a Internet IPsecVPN connection between two sites using Cisco ASA5505 A site currently has following setup.(Same setup is expected in another site) Internet-----ADSL Router-----Juniper SSG5-----Intranet (Im not sure what is configured on SSG5 and if router is in bridge mode or if NAT is configured) I was thinking if I should install ASA5505 along with Juniper SSG5? Internet-----ADSL Router-----Juniper SSG5-----Cisco ASA5505(for vpn only)------Intranet or Internet-----ADSL Router-----Cisco ASA5505(for vpn only)-----Juniper SSG5------Intranet My question is if it is possible? What should be the normal way to achieve this goal? Thanks

    Read the article

  • Setup Cisco RVS4000 QOS for VOIP

    - by andyknas
    Just switched from dedicated T1's with analog phone lines to cable modem with 10/2 uplink. We're having some VOIP call quality issues on the outgoing side when bandwidth is stressed and I need to setup QOS or a VLAN on our RVS4000 router. Currently all phone traffic (talkswitch device and ip phones) are on it's own d-link PoE switch, and all workstations are on a LinkSys 1GB switch. Both switches are plugged into ports on the RVS4000. I'd like to set it up so that the dlink port has ~512Mbsp dedicated to it for voice at all times. It's my understanding that with a VLAN or QOS I can set this up. I've got QOS setup already with port 5060 to have high priority but it doesn't seem to make a difference.

    Read the article

  • Setup Linksys 3200 remote access

    - by Greg
    I'm trying to setup remote access for my linksys 3200 so that I can configure it through the WAN port. I have turned on remote access, however when I try to connect I get a 404 error. The settings I have are: When I try to access xxx.xxx.xxx.xxx:9999 I just get a 404 error. I have allowed RDP access to a computer behind the router and this works fine on the same IP address. Any idea's on what else I have to do to allow remote management access? UPDATE: I tried changing the port to 80 and it works. Change it back to any other number and it doesn't work. Modem is setup with a DMZ to the router's IP. Why does it only work on port 80? BTW I can't use port 80 because there is a website hosted behind the router.

    Read the article

  • Do I have an efficient APC Setup?

    - by Gaia
    Regarding my particular APC setup: APC 3.1.9 PHP 5.3.3 via fCGI Apache 2.2.15 CentOS 6.3 1) Is it setup properly to minimize overall memory usage? /etc/php.d/apc.ini has only one line: "apc.cache_by_default=0" Each domain for which I want to turn on APC has all the apropriate APC configurations in its own php.ini. 2) I would like to keep only one copy of apc.php that can be accessed via any of the vhosts on the server. What's the recommended way to do this? It seems that apc.php doesn't play well with apache Alias directive. apc.php only exists is on one of the vhosts, is set to 644 and it doesn't seem to matter who owns it: if I try to access it via an alias I get only gibberish.

    Read the article

  • Synergy setup broke on upgrade

    - by CoatedMoose
    I had synergy setup working fine with version 1.3.7, however I got a new computer and decided to set it up as well. Because the setup I was working with was ubuntu (server - dual monitors) mac (client) and the new computer (replacing the mac) was windows, I ended up updating everything to 1.4.10. ______ ______ ______ | mac | ubu1 | ubu2 | |______|______|______| The problem is currently that dragging to the left of ubu1 causes the cursor on the mac to flicker briefly and then the cursor shows up at the bottom right corner of ubu2. Here is my .synergy.conf section: screens Andrews-Mac-Mini: ctrl = ctrl alt = meta super = alt Andrew-Ubuntu: end section: links Andrew-Ubuntu: left = Andrews-Mac-Mini Andrews-Mac-Mini: right = Andrew-Ubuntu end And the output from synergys -f NOTE: client "Andrews-Mac-Mini" has connected INFO: switch from "Andrew-Ubuntu" to "Andrews-Mac-Mini" at 1679,451 INFO: leaving screen INFO: screen "Andrew-Ubuntu" updated clipboard 0 INFO: screen "Andrew-Ubuntu" updated clipboard 1 INFO: switch from "Andrews-Mac-Mini" to "Andrew-Ubuntu" at 2398,833 INFO: entering screen

    Read the article

  • Windows-Server-2003 setup on Dell-PowerEdge R310 is hanging [closed]

    - by Robert Rose
    Possible Duplicate: Problems installing OS on Dell PowerEdge R410 I am trying to configure a Dell PowerEdge R310 server with Windows Server 2003. I've already configured the two hard drives as RAID1. The HD controller is PERC H700 Integrated and Adapter. Trying to stay with Windows Server 2003 on this fairly new server to save on cost and keep the configuration the same as my old server, which has been running like a champ for five years. Problem: During the OS installation, after everything has been copied from the installation CD, the installation hangs at a window labeled 'Windows Setup' with the message 'Setup is starting Windows' at the bottom. I'm wondering if this is a driver problem and if so, where can I get the drivers for the R310 or where can I get the media for the latest version of Windows Server 2003 which may include the necessary drivers? Will certainly appreciate some help here.

    Read the article

  • Implementing a Linux-HA based clustering setup on Windows

    - by Alex
    I have a (tried and tested) setup involving: 2x Load balancing nodes on a floating IP via Heartbeat, load balancing 2 tomcat servers. 2x Tomcat servers 2x Galera Cluster MySQL servers synchronously replicating (+1 arbitrator node) All are evenly spread across 2 physical nodes. Now, I have to somehow get the same functionality on Windows Server (2008? I think) nodes .... running under Xen virtualization. There is no possibility to use Linux for any of the nodes. I count two main problems: No Linux-HA hearbeat daemon for the load balancing No Galera synchronous replication for MySQL I freely admit to having nearly no Windows knowledge when it comes to clustering. Is there a way to closely mimic the setup I have described or is it a total write-off?

    Read the article

  • How to setup separate MySQL and PHP VPS servers

    - by Fazal
    Someone recommended I should have my MySQL server separate from my Apache/PHP server in case of hacking and such. By visiting linode, slicehost and various articles here on serverfault I've managed to cobble together a decent set of instructions on how to do the Apache/PHP bit. I'm using Rackspace VPS and they provide an internal IP for each server. If I setup a MySQL VPS, should I assume that I would just add the internal IP for the database host? And I guess that I would only need to open up my default ssh port and mysql ports and install phpmyadmin on there? Ideally I would have webserver.mydomain.com and dbserver.mydomain.com (two 256mb VPS's) with servermin on webserver.mydomain.com and phpmyadmin on dbserver.mydomain.com. If anyone has any guides or advice on how to setup this type of solution I'd be more then grateful!

    Read the article

  • How to grow from single server setup

    - by Jenkz
    I'm looking for resources on how to grow our server setup. We currently have one dedicated server with Rackspace in the UK of the following spec: HPDL385_G2_PrevGen HP Single Dual Core Opteron 2214 (2.2Ghz) 4GB RAM 2x 10,000 SCSI Drives in RAID 1 Our traffic is up to 550,000 UVs per month. The site runs off a PHP and MySQL setup. The database gets an absolute hammering, we have many complex queries joining multilpe tables. We are using APC for PHP caching. I'm getting to the stage where I've done as much DB and query optimisation as I can and wonder what the next step should be...... I've looked at memcache, but I've got the impression that his requires a large amount of RAM and ideally a dedicated box.... So is the next step to have two boxes; one for database, one for Apache? Or is there a step I've overlooked. Our load is usually around the 2 mark, but right now it's up at 20!

    Read the article

  • How to grow from single server setup

    - by Jenkz
    I'm looking for resources on how to grow our server setup. We currently have one dedicated server with Rackspace in the UK of the following spec: HPDL385_G2_PrevGen HP Single Dual Core Opteron 2214 (2.2Ghz) 4GB RAM 2x 10,000 SCSI Drives in RAID 1 Our traffic is up to 550,000 UVs per month. The site runs off a PHP and MySQL setup. The database gets an absolute hammering, we have many complex queries joining multilpe tables. We are using APC for PHP caching. I'm getting to the stage where I've done as much DB and query optimisation as I can and wonder what the next step should be...... I've looked at memcache, but I've got the impression that his requires a large amount of RAM and ideally a dedicated box.... So is the next step to have two boxes; one for database, one for Apache? Or is there a step I've overlooked. Our load is usually around the 2 mark, but right now it's up at 20!

    Read the article

  • How to setup a 1 way trust, Windows Server 2008 R2

    - by MichaelOz
    I am on my home network and connect to workplace via a VPN. I have a DC on my home network (DC1 , domain = home). How can I setup a 1 way trust, so that I am able to run executables, such as SQL Management Studio using RunAs - then type in credentials for work domain? First question is, will a 1 way trust solve this, and can I set this up without bothering a network admin at workplace (assuming I have a domain account with enough permissions on work domain) If yes - any good step by step guide to setup 1 way trust? Server is Windows Server 2008 R2. As mentioned its DC running DNS Role too. Thanks in advance

    Read the article

  • Setup asp.net mvc application as subdomain website

    - by a_m0d
    I'm trying to setup a local application on a subdomain on our company server. There is already an installation of sharepoint running on http://companyweb/, but I would like my application to run on http://orders.companyweb/. I tried creating a new website, leaving the IP address the same as it is for http://companyweb, and just changing the host header value to orders.companyweb. However, no matter where I try to access the site from (different computers around the network, including the server itself), I keep getting 404 errors. I then tried setting up a simple index.html and serving that up as the highest priority; however, I still got 404 errors. This makes me think that I have actually setup the site itself wrong. What should I change to be able to access this application correctly on all the local computers?

    Read the article

  • Samba setup to request password reset on first time login

    - by crazybyte
    Is it possible to setup Samba to ask for password reset when the user first logs in without the need to setup a domain controller? Would this work properly with Windows clients or with clients using Linux with file managers like Krusader or Nautilus? Could somebody give me a few pointers how to implement this if is possible? I'm pretty new to Samba and I use it as a file server and I would like to have such a feature on it, but I'm not sure if it's possible. Thanks!

    Read the article

  • Setup mutt to read through a threaded message and then return to the email index

    - by dat5h
    I have begun using mutt (terminal email client) recently and I have it setup very nicely and easy to use. My only gripe is that sometimes it is difficult to tell when I transition from one thread to the next. Is it possible to setup the bindings such that moving to the next-undeleted message would check if the next-undeleted message is in the same thread, and if that check is false it returns to the index or throws an error? For example, I currently have bind pager <down> next-undeleted bind pager } next-subthread Is there a more advanced function call that could perform this check? I haven't been able to find much on how to perform more complex function calls with such checks while checking out the manual. Any help would be appreciated.

    Read the article

  • How to benchmark apache/nginx setup

    - by Saif Bechan
    I am planning to setup nginx as reverse proxy. I will have apache to deliver my dynamic content, and nginx will deliver the static content. My configuration i have now is just Apache with fastCGI. This gives me no configuration problems and runs great. After I have set up nginx I want to run some benchmarks to see if I really got some performance increases, else i will switch back. Does anyone know how I can benchmark this type of setup? Or maybe someone did this already and have some canned results, I will be glad to hear them.

    Read the article

  • Windows Setup could not configure Windows to run on this computer's hardware

    - by Hello71
    The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

    Read the article

  • Setup Windows Media Player 11 to stream from TVersity

    - by snorfys
    I've got TVersity installed on a Windows 2003 server box (work had an extra license that they donated to let me install at home to get some practice setting up/administering a domain etc.) I found out that Windows Media Player 11 won't install on Windows 2003, but installed TVersity instead and streaming to my 360 is working great. Problem is that I don't know how to setup streaming to any other PC on the network. All of the PCs have access to the shared network folder, but playing from there doesn't stream and the stutter is pretty bad. Is there a way to setup Windows Media Player 11 or another player to stream from TVersity?

    Read the article

  • How to setup a web server with remote SMTP

    - by IP
    I have 2 severs, both running server 2008 (R2) One is the web server, one is running as a mail server. The setup I want is that any mail sent from apps (php, asp and asp.net) on the web server are sending mail through the mail server's SMTP server...but this seems to be proving trickier than i'd hoped. The mail server is running MailEnable, and the web server IIS7 (maybe 7.5) What i don't want is to setup an open relay SMTP server on the web server, as this is going to be open to abuse (even if I just allow relay from local address). the problem is, there doesn't appear to be a way to specify credentials in php so if I point it at the mail server, then the mail server has to be set as an open relay, which is almost worse. Any ideas how I should be doing this?

    Read the article

  • How to setup ssh's umask for all type of connections

    - by Unode
    I've been searching for a way to setup OpenSSH's umask to 0027 in a consistent way across all connection types. By connection types I'm referring to: sftp scp ssh hostname ssh hostname program The difference between 3. and 4. is that the former starts a shell which usually reads the /etc/profile information while the latter doesn't. In addition by reading this post I've became aware of the -u option that is present in newer versions of OpenSSH. However this doesn't work. I must also add that /etc/profile now includes umask 0027. Going point by point: sftp - Setting -u 0027 in sshd_config as mentioned here, is not enough. If I don't set this parameter, sftp uses by default umask 0022. This means that if I have the two files: -rwxrwxrwx 1 user user 0 2011-01-29 02:04 execute -rw-rw-rw- 1 user user 0 2011-01-29 02:04 read-write When I use sftp to put them in the destination machine I actually get: -rwxr-xr-x 1 user user 0 2011-01-29 02:04 execute -rw-r--r-- 1 user user 0 2011-01-29 02:04 read-write However when I set -u 0027 on sshd_config of the destination machine I actually get: -rwxr--r-- 1 user user 0 2011-01-29 02:04 execute -rw-r--r-- 1 user user 0 2011-01-29 02:04 read-write which is not expected, since it should actually be: -rwxr-x--- 1 user user 0 2011-01-29 02:04 execute -rw-r----- 1 user user 0 2011-01-29 02:04 read-write Anyone understands why this happens? scp - Independently of what is setup for sftp, permissions are always umask 0022. I currently have no idea how to alter this. ssh hostname - no problem here since the shell reads /etc/profile by default which means umask 0027 in the current setup. ssh hostname program - same situation as scp. In sum, setting umask on sftp alters the result but not as it should, ssh hostname works as expected reading /etc/profile and both scp and ssh hostname program seem to have umask 0022 hardcoded somewhere. Any insight on any of the above points is welcome. EDIT: I would like to avoid patches that require manually compiling openssh. The system is running Ubuntu Server 10.04.01 (lucid) LTS with openssh packages from maverick. Answer: As indicated by poige, using pam_umask did the trick. The exact changes were: Lines added to /etc/pam.d/sshd: # Setting UMASK for all ssh based connections (ssh, sftp, scp) session optional pam_umask.so umask=0027 Also, in order to affect all login shells regardless of if they source /etc/profile or not, the same lines were also added to /etc/pam.d/login. EDIT: After some of the comments I retested this issue. At least in Ubuntu (where I tested) it seems that if the user has a different umask set in their shell's init files (.bashrc, .zshrc,...), the PAM umask is ignored and the user defined umask used instead. Changes in /etc/profile did't affect the outcome unless the user explicitly sources those changes in the init files. It is unclear at this point if this behavior happens in all distros.

    Read the article

  • Openfire on Mac OS X: can't log in after setup

    - by Tom
    Hey all, I'm trying to set up Openfire (http://www.igniterealtime.org/projects/openfire/) on Mac OS X. The install goes well, and I can start the server and enter the admin console via its System Preferences pane. I run the setup, including specifying the password for the admin user. However, when I try to log into the admin console, I get the message "Login failed: make sure your username and password are correct and that you're an admin or moderator." What gives? I've tried to RTFM, but the documentation seems to be really sketchy. Nowhere is the setup process mentioned in the install docs.

    Read the article

  • Installing Windows 7 over PXE, preferably with domain autojoin

    - by Ivan Vucica
    At an educational non-profit, I've inherited a previously set-up Windows domain that, after the first reinstall of the machines, we ended up not using by simply not joining machines back into the domain. Over last summer, before the annual reinstall for shipping machines to the summer school, I toyed with the idea of installing Windows 7 over network, instead of just imaging the machines. It took a bit longer than I expected to figure out the basics; honestly, I expected that Windows would be more friendly for PXE installation out of the box. What I'm interested in is best practices for installing Windows 7 over PXE with domain autojoin. I'd love it if the whole setup could optionally be hosted on a UNIX based system as well. I've had some success by preparing an ISO using Windows Deployment Kit, and loading the ISO into memory. This was needed since I wanted a menu, and I think I couldn't get PXELINUX to chainload into Windows' bootloader. Unfortunately, I couldn't figure out much about customization of the Windows setup in that timeframe nor could I get Samba to work properly; studying the stuff ended up being too lengthy, especially the portion where I edited a disk image on Windows and copied it outside. WDK didn't make things easier by mounting the disk image into RAM, and writing it in its entirety when done with it, making me a very sad boy. I've recently found a different approach, too, that appears to be closer to Microsoft's original idea for netboot deployment and does not involve ISOs. So my question boils down to the following. What exact approach do you use for netbooting Windows 7 setup? How can Windows 7 setup be best customized to be completely unattended, including installation on specific system partition and not destroying the data partition, creation of passworded admin and default user, choice of MAC-address-based hostname, and joining a domain? As much details as possible for everyone's future reference would be appreciated. WDS isn't a bad choice, but if a Linux-based install can be used, that'd be better.

    Read the article

  • Resilient Linux Mail Server Setup

    - by Coops
    How would people design a resilient mail server setup with Linux? On an application level what the system needs to provide is both an incoming and outgoing mail service (i.e. SMTP & IMAP), along with filtering and archive storage (the archive part isn't critical yet, so we'll look at this later probably). What is required on top of this is a resilient system, i.e. one which will handle individual server failures without interrupting service. As such I would term this a High Availability mail system. This is in contrast to a High Performance mail setup, as in our case the volume of mail being handled isn't the important factor, it's simply that it stays online. Having not approached this problem before, the first thing I thought of was a clustered file system (gfs/gluster/etc), combined with heartbeat to failover a floating IP to another box in the case of a server failure. Combined with postfix & dovecot does this sound feasible to people?

    Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >