Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 370/1359 | < Previous Page | 366 367 368 369 370 371 372 373 374 375 376 377  | Next Page >

  • nomachine NX: Text missing on all gtk interface (Unity and Gnome Classic)

    - by hansioux
    [Edit] I later realized my issue only occurs when I am using NX to remote access my machine. Therefore I edited the title and description. I have also found the temp solution, which is to "disable render extension" in the custom display settings. But doing so makes the NX experience very slow laggy, and not that nice to look at. [/EDIT] I did a fresh install on a new computer, and was trying to setup my fonts. When I log in remotely via NX, my the text are missing on all gtk based interfaces. That means most menues (except for unity), right click menues, applications themselves, terminal, and so on. About the only thing unaffected is firefox. all the texts are showing just fine for firefox. So that probably already says something about text permissions. I went to check if my fonts have the correct permissions and they do. I removed my custom settings from /etc/fonts/config.d, and still the texts are missing. There is a work around by using "disable render extension" in the custom display settings. How do I fix this issue permanently?

    Read the article

  • ubiquity "hangs" on first step

    - by bumbling fool
    Trying to install 11.04 daily for the last couple days but, no matter what I try (wifi connected, wifi not connected, disk blank, disk prepartitioned...), if just "hangs" at the first window (pick your language) with a non-stop hourglass after hitting next. I ran into a different issue when trying to use the alternate installer image. This is on a Stinkpad T42. Should ubiquity at least tell me whats going on?!? I tried to find a log but /var/log/installer* isn't present.

    Read the article

  • fix pavucontrol Alsa mixer with creative card

    - by schwiz
    I have been desperately trying to get my creative x-fi soundcard to work with my 10.10 install and I am almost there! I have 1 speaker working and when I open volume control I see that my device is Creative X-fi (Also mixer). However, it appears to be stuck on mono. When I open pavucontrol I get a message that says Connection failed: Connection refused and it exits. Before it closes I can see that playback is set to mono but it won't let me change before it closes. Can someone help me over this last hump? I am running 32 bit 10.10 any advice is much appreciated.

    Read the article

  • How do I set up multi seat?

    - by JJ Mcfly
    Hi I was hoping to have a 2 seat setup. One will be for my TV just going to run Boxee. The other is for my main Desktop. I've been looking for a good guide to help me navigate this, I'd like to use ubuntu 10.10. I am assuming it's just a case of getting a box + 2 graphics adaptors and 2 usb mice and keyboards, one of which will be bluetooth for the TV. I can't seem to find much documentation on this idea. Can anyone point me in the right direction? Also I am assuming that this is all possible with a standard ubuntu install, but with some additional configuration. Thank you in advance for any advice you can offer me JJ Mcfly

    Read the article

  • sudo & redirect output

    - by Khaled
    I have a small question regarding using sudo with output redirect >. To enable IP forwrding, someone can use the command: $ echo 1 > /proc/sys/net/ipv4/ip_forward Executing this command will give permission denied as it requires root privileges. However, executing the same command with sudo gives also permission denied error! It seems that output redirect > does not inherit the permissions of the preceding command echo. Is this right? As a workaround I do: $ echo 1 | sudo tee /proc/sys/net/ipv4/ip_forward Is this the best way to do it? Am I missing something? Please, note that this is an example and it applies to all commands that use output redirect.

    Read the article

  • Unity 3D does not work on Dell system with a AMD Radeon HD 6470M

    - by VeeKay
    I am running 64 bit Ubuntu on Dell with 1GB graphic card. I login with "Ubuntu" hoping to see Unity 3d but it doesn't. Unity 2D runs instead. when I type in echo "$DESKTOP_SESSION" it confirms the Unity-2D. I've checked the System info that shows like : The graphics row shows itself as empty. SO I've presumed that the graphic drivers aren't detected and hence I went to Unity- Additional Drivers and installed the fglrx driver that the UI has suggested. Even after installing so, the graphics part in System info details shows nothing and still Unity 2D runs in spite of all the effort. Please help! How can I get my Unity 3D back? Hardware Info Video Card : AMD Radeon™ HD 6470M - 1GB (For ICC) RAM : 6GB (1 X 2GB + 1 X 4GB) 2 DIMM DDR3 1333Mhz OS : 64 bit Ubuntu 11.10 Edit : Output for /usr/lib/nux/unity_support_test -p X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 155 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 21 Current serial number in output stream: 21

    Read the article

  • Infrared usb adapter not hot pluggable?

    - by A. Goossens
    For transferring exercise files from my Polar heart rate monitor i use the software Protrainer 5 with an external infrared usb adapter. Using Wine to run Protrainer 5 and some adjustments mentioned here (using irda-utils) i managed to make it work. Well, sort of: every time i want to transfer exercise files and the adapter is not plugged in i have to reboot my laptop with the usb adapter plugged in to make it work. Since i have a laptop it unfortunately is no option to just always leave the adapter in. It seems to me that the usb adapter isn't hot pluggable (which seems odd for a usb device) or there must be another problem. Polar WebLink (other software to transfer exercise files) experiences the same issue. Can anyone help me to fix this problem? Infrared usb adapter: Polar IRDA USB adapter OS: Ubuntu 12.10 (64-bit) Hardware: Lenovo Thinkpad T500

    Read the article

  • How to change keyboard layout?

    - by swedishhh
    I'm on ubuntu 12.04. Recently I bought a cheap apple style bluetooth keyboard. It pairs OK. I paired it with the current 102 key still attached. Anyway I noticed that the character mapping is incorrect. Most keys do not type anything - some keys on the right (k, l, ;') etc give numbers, but that's about it. So I rebooted, with 102 kbd unattached, and the bluetooth keyboard on, ready to connect. After boot at the login screen, the bluetooth keyboard had paired. I typed my password, and it logged in fine!! However after the user login was complete it reverted to the broken behaviour. A glance at the layout chart shows ubuntu thinks I still have the 102 layout, even though it remained disconnected. Any ideas? Thanks, Dave

    Read the article

  • Is there any way I can run xampp on 11.10 x64?

    - by Siddhartha
    Running xampp says it requires a 32 bit system. Is there a workaround, or a different software I can use?? I am indeed aware of the lamp-server installation available in Ubuntu, and am currently using it. But I was specifically asking for a integrated LAMP software like xampp which makes it easier to manage the LAMP installation. Currently xampp runs only on x86 systems, and I have a x64 bit install. Hence the question.

    Read the article

  • Unity dash search

    - by To Do
    I have my personal folders to a different partition other than home, I had a series of symlinks in my home folder pointing to the folders on the other partition. This was causing multiple entries in Dash search do I modified my ~/.config/user-dirs.dirs file pointing them to the folders on the second partition. The issue is that when I search for any one of these folders in Dash, I still get two entries, one pointing the folder and another that points to the /home/username/Documents folder. If I click on this link I get a Could not find /home/username/Documents error. Why is this and how do I delete these entries from Dash's records? If deleting records is not possible, is there a way to "reindex" the dash search database?

    Read the article

  • Storing deb packages on local media

    - by Saeid87
    Is there a way to store deb packages (all or a specific version of package) on a local media (dvd, usb etc...) so later I would be able to install those packages on a PC which does not have Internet connection? For example, these are the packages that I want to install on a PC which doesn't have Internet connection: # TinyOS MSP430 GCC Compiler Repository # Version 4.6.3 deb http://tinyprod.net/repos/debian squeeze main deb http://tinyprod.net/repos/debian msp430-46 main # TinyOS version 2.1.2 deb http://tinyos.stanford.edu/tinyos/dists/ubuntu lucid main

    Read the article

  • Best partition scheme [WIN7 | Ubuntu | Media | Home]

    - by Rockiano
    I just got a new HD (750GB of which 700GB are usable) and I want to partition it taking in consideration: Media (200GB) Home (300GB) Win7(150GB) Ubuntu(50GB) (I have 6GB of ram, would i need to consider a swap partition) The Media and Home partitions usually are left untouched, but once a month (or in some cases more) I will be formatting Win7 and/or Ubuntu, changing their sizes and even creating a third partition for a second ubuntu/win7 instance (using the 200GB originally assigned for them) What would be a good/best partition scheme to avoid problems in the Media and Home partition (And the hard-drive in general), considering they are highly unlikely to change and that also the Win7 partition is the less unlikely to be changing in relation to the ubuntu partition? I hope I'm clear enough and if any more details are missing please let me know. Thank you in advance.

    Read the article

  • Support TrendNet TEW-643PI Wireless N network card

    - by Matthew Rigdon
    Hello, Has anyone been able to get a TrendNet TEW-643PI Wireless N card working under UBUNTU, if so what drivers did you use and where did you find them. I have this card and would really like to be able to use it in my computer. I found drivers that may work but dont know how to get ubuntu to pick up the drivers. I have tried the Additional Drivers option but cannot seem to get ubuntu to pick up the drivers. Thanks.

    Read the article

  • How to recognize an optimus laptop?

    - by kellogs
    kellogs@kellogs-K52Jc ~ $ lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 80) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 80) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 80) 03:00.4 System peripheral: JMicron Technology Corp. xD Host Controller (rev 80) 03:00.5 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 03) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) kellogs@kellogs-K52Jc ~ $ inxi -SGx System: Host: kellogs-K52Jc Kernel: 3.5.0-17-generic x86_64 (64 bit, gcc: 4.7.2) Desktop: KDE 4.9.5 (Qt 4.8.3) Distro: Linux Mint 14 Nadia Graphics: Card: Intel Core Processor Integrated Graphics Controller bus-ID: 00:02.0 X.Org: 1.13.0 drivers: intel (unloaded: fbdev,vesa) Resolution: [email protected] GLX Renderer: Mesa DRI Intel Ironlake Mobile GLX Version: 2.1 Mesa 9.0.3 Direct Rendering: Yes kellogs@kellogs-K52Jc ~ $ lshw [...] *-display description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 18 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:d0000000-d03fffff memory:c0000000-cfffffff ioport:e080(size=8) Manufacturer advertises the K52Jc model which I bought as optimus enabled. However, no traces of it in the output above. Of course, Bumblebee would not start on this machine. Should I rest assured that is a defective / un-optimused machine ?

    Read the article

  • E: unable to locate package firmware-b43-installer when i

    - by Raju
    I am using Acer aspire-5002wlmi laptop and set up a dual boot with Windows XP and Ubuntu 12.04. Wifi is well working in XP but when I start Ubuntu I will get the below error. [ 95.514855] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all the instruction on this website. then I followed the instructions from the below link file:///C:/Documents%20and%20Settings/MGL/Desktop/how%20to%20install%20ubuntu/Ubuntu%2012.04%20Splash%20Screen%20Lockup%20with%20LiveCD%20_%20Ben%20Rousch%27s%20Cluster%20of%20Bleep.htm but I am stuck in installing the Broadcom Wifi firmware in terminal and it is showing this error: E: unable to locate package firmware-b43-installer

    Read the article

  • Ubuntu boot problem/unity failure

    - by Kenny
    So here I am sitting in a big pile of muck...over the last 2 days things have just been going from bad to worse with version of Ubuntu 12.10. So 2 days ago I was fiddling around with kismet and airmon-ng. I had added a bunch of libraries, I remember adding GTK+, Glib, Pango, etc. After restarting the other day my desktop opened fine but my background was changed to the default and none of my files on the desktop were visible and the top bar and side bar were not visible or functioning. The window managers were still working. I then tried reinstalling my nvidia drivers to see if that would change anything, it did not. Then after doing some searching online I found something that suggested I try deleting the file "libgtk-3.so.0". I deleted this and tried to restart the computer. Upon restart, I was greeted by a black screen with some writing saying something about -starting clamAV [OK] -problem with Apache Server could not verify correct...something... - checking battery state [ok]. After it gets to battery state it just stops and sits there indefinitely. So to sum, I cannot login to ubuntu because it just sits at this black screeen. If anyone has any idea as to what is going on and how to fix it please let me know. Thanks!

    Read the article

  • Install a different version of a package

    - by Michael Wiles
    I'm running lucid server and have installed tomcat. The version it installed is 6.0.24-2ubuntu1.6. Is this the version I'm tied to? Is it possible to install a more recent version? The one available from maverick is 6.0.28. Maybe I can add a source to provide my lucid install with this version? In the package manager user interface I can "force version". Is it possible to force version from command line alternative as well?

    Read the article

  • Unable to boot Ubuntu with new Kernel but it works fine with old kernel

    - by user93808
    I recently acquired a Samsung Series 9-900x3c and installed Ubuntu 12.04 LTS on it. Now I wanted to upgrade to the most recent kernel and after grabbing the packages from kernel.ubuntu.com/~kernel-ppa/mainline/ and installing them via dpkg Ubuntu fails to boot. I can select the appropriate Kernel version in grub but when I try to launch the Ubuntu with kernel 3.6 nothing happens. On the other hand Kernel 3.2.x works fine for me. Any suggestions what I can do to use the most recent Kernel? Thanks a lot in advance. Cheers JO

    Read the article

  • Why is my system freezing when I switch users

    - by ZeroDivide
    Hello I've recently upgraded from 13.04 to 13.10 64bit. I'm running AMD graphics with the proprietary drivers. I have two user accounts. Mine(administrator) and my girlfriend's(standard) My girlfriend clicks "switch user" from my lock screen and logs in fine. I then try to click "switch user" from her lock screen and everything goes black. Then the monitor blinks on and off with just a single cursor. I have no way to access the terminal, the system is unresponsive and I have to hit the power button. Even ctrl + alt + f4 or ctrl + alt + t doesn't get me a terminal. When I press the power button on my system, it does start printing out the shutdown sequence on the monitor. Here is my .xsession-errors Script for ibus started at run_im. Script for auto started at run_im. Script for default started at run_im. Here is hers: init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd respawning too fast, stopped init: logrotate main process (4726) killed by TERM signal init: upstart-dbus-session-bridge main process (4865) terminated with status 1 init: gnome-settings-daemon main process (4843) terminated with status 1 init: gnome-session main process (4852) terminated with status 1 init: unity-panel-service main process (4863) killed by KILL signal I found some advice in a forum to look for at-spi2-registryd in my system logs. Perhaps it will be useful. executing this: sudo grep -r at-spi2-registryd /var/log/* produces this: /var/log/lightdm/x-1-greeter.log:** (at-spi2-registryd:4384): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-1-greeter.log:** (at-spi2-registryd:4384): WARNING **: Unable to register client with session manager /var/log/lightdm/x-2-greeter.log.old:** (at-spi2-registryd:7447): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-2-greeter.log.old:** (at-spi2-registryd:7447): WARNING **: Unable to register client with session manager /var/log/lightdm/x-0-greeter.log:** (at-spi2-registryd:1378): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-0-greeter.log:** (at-spi2-registryd:1378): WARNING **: Unable to register client with session manager /var/log/lightdm/x-0-greeter.log.old:** (at-spi2-registryd:1357): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-0-greeter.log.old:** (at-spi2-registryd:1357): WARNING **: Unable to register client with session manager Any ideas what is going on?

    Read the article

  • Ubuntu Splash Screen Customization

    - by Galaxy7
    I wanted to know how to customize the splash screen in Ubuntu 13. I have tried to install Plymouth Manager but when I run sudo apt-get update it says it was unable to fetch http://ppa.launchpad.net/mefrio-g/plymouthmanager/ubuntu/dists/raring/main/binary-i386/Packages. I opened the address in Firefox but it didn't open. Also I would like to know where the files for the Ubuntu Logo, Splash Screen Background, etc. are located (to customize them). In previous versions they were located at usr/share/images. I am running Ubuntu 13 Raring Ringtail on VMWare Player. The host is an Acer 5600U running Windows 8. Thnx.

    Read the article

  • Install latest ffmpeg for all users in Debina/Ubuntu

    - by Junaid
    I installed ffmpeg on my Ubuntu using the guide: https://ffmpeg.org/trac/ffmpeg/wiki/UbuntuCompilationGuide It is good and working. I know that guide is for installing ffmpeg for current user. Can anybody help me to install ffmpeg for all users? To do so I think there required only few changes in the steps specified at https://ffmpeg.org/trac/ffmpeg/wiki/UbuntuCompilationGuide . But I am not sure about that. Please help Thank you.

    Read the article

  • Unable to change user password in Ubuntu 12.10

    - by Laphanga
    The User Password is not changing for some reason. In the terminal it says password updated successfully, $ sudo passwd [sudo] password for zaigham: Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully But when I try to log in using the new password it doesn't work. I have changed my password 2, 3 times now but still it's the same. Is that some kind of bug?

    Read the article

  • Ubuntu not showing complete list of partitions while installing 10.04 and 10.10

    - by Ravi
    I am a total beginner to Ubuntu. I have tried to install Ubuntu on my 320 gb hard disk and am stuck at the partition page. The problem is, Ubuntu is not showing all the partitions. When I run the live CD and try to see all the drives these are not present. I have presently 4 drives, C: 58 GB D: 48 GB E: 87 GB and F: 102 GB. The F: drive is not shown; at the time of installing it does not show any of the drives, just a chunk of 257 GB, hence I am unable to install Ubuntu on my D: drive. On the C: drive, Windows 7 64 bit is installed.

    Read the article

  • iptables -L lags on non localhost or anywhere address

    - by DazSlayer
    I am trying to configure iptables for ubuntu 10.04 and I have a problem with iptables -L lagging on rows where the destination or source address is not localhost or anywhere. The following entries will cause lag on their row: iptables -A INPUT -p tcp --dport 111 -s 192.168.1.14 -j ACCEPT iptables -A INPUT -p tcp --dport 90 -d 192.168.1.14 -j ACCEPT while this does not: iptables -A INPUT -p tcp --dport localhost -s 192.168.1.14 -j ACCEPT iptables -A INPUT -p tcp --dport localhost -d 192.168.1.14 -j ACCEPT I feel like this might be due to iptables checking to see if the ip is reachable. If not, what is the cause, if it is how can I disable it?

    Read the article

  • double-click does not open the default program

    - by Chang
    I installed Ubuntu 12.04, with texlive-full and texworks. When I double-click a .tex file in Nautilus, it pops up a Do you want to run "xxxxxxxx.tex", or display it contents? "xxxxxxxx.tex" is an executable text file. Run in Terminal Display Cancel Run If I choose Display, it opens texworks. How can I make it open without seeing the above conversation window? By the way, is .tex file indeed an executable file? ADDED Just for the case, my ~/.local/share/applications/mimeapps.list file looks like the following: [Default Applications] text/html=google-chrome.desktop x-scheme-handler/http=google-chrome.desktop x-scheme-handler/https=google-chrome.desktop x-scheme-handler/about=google-chrome.desktop x-scheme-handler/unknown=google-chrome.desktop text/x-tex=texworks.desktop x-scheme-handler/mailto=google-chrome.desktop [Added Associations] text/x-tex=texworks.desktop; text/x-bibtex=jabref.desktop;gedit.desktop; I observe texworks are both up and down. Should I remove one? ADDED This does not happen with all .tex files. In fact, I am currently using Ubuntu 12.04 under Virtual Box with Windows 7 host. I have my Dropbox account synced with the Windows 7 host, and I access files in Dropbox in Ubuntu through Virtual Box's shared folder functionality. (I didn't install Dropbox client in Ubuntu.) Files in Dropbox are owned by root with group vboxsf. My personal account is in the group vboxsf. It seems that I have to uncheck the option for "executable", but I have all my .tex files in the Dropbox shared folder. Would there be any workaround?

    Read the article

< Previous Page | 366 367 368 369 370 371 372 373 374 375 376 377  | Next Page >