Search Results

Search found 34668 results on 1387 pages for 'return'.

Page 370/1387 | < Previous Page | 366 367 368 369 370 371 372 373 374 375 376 377  | Next Page >

• Agilent E4426B signal generator locks up during multiple GPIB *SAV operations

  - by aspiehler

  I have a test fixture with an Agilent E4426B RF signal generator connected to a PC via a National Instrument Ethernet-to-GPIB bridge. My software is attempting to sanitize the instrument by presetting it and then saving the current state to all of the memory locations writable via the standard SCPI command "*SAV x,y". The loop works to a point, but eventually the instrument responds with an error and continuously displays the "L" icon on the front display and a "Remote preset" message at the bottom. At that point it won't respond to any more remote commands and I have to either cycle power or press LOCAL, then PRESET at which point it takes about 3 minutes to finish presetting. At that point the "L" icon is still present and and the next GPIB command sent to the instrument causes it to report a -113 error (undefined header) in the instrument error queue. I fired up NI spy to see what was happening, and found that the error was happening at the same point in the loop - "*SAV 6,2" in this case. From NI Spy: Send (0, 0x0017, "*SAV 6,2", 8 (0x8), NLend (0,0x01)) Process ID: 0x00000520 Thread ID: 0x00000518 ibsta:0xc168 iberr: 6 ibcntl: 2(0x2) And here's the code from the instrument driver: int CHP_E4426b::Erase() { if ((m_StatusCode = Initialize()) != GPIB_SUCCESS) // basically just sends "*RST" return m_StatusCode; m_SaveState = "*SAV %d, %d"; for (int i=0; i < 10; i++) for (int j=0; j < 100; j++) { sprintf(m_CmdString, m_SaveState, j, i); if ((m_StatusCode = Send(m_CmdString, strlen(m_CmdString))) != GPIB_SUCCESS) return m_StatusCode; } return GPIB_SUCCESS; } I tried putting a small Sleep() delay (10-20 ms) at the end of the inner loop, and to my surprise it caused the error to show up earlier rather than later. 10 ms caused the loop to error out at 44,1 and 20 ms was even sooner. I've already eliminated faulty cabling or the instrument as the culprit. This same type of sequence works without any error on a higher end signal generator, so I'm tempted to chalk this up to a bug in the instrument's firmware.

  Read the article

• Vaadin: Downloaded file has whole path as file name

  - by javydreamercsw

  I have a download action implemented on my Vaadin application but for some reason the downloaded file has the original file's full path as the file name. Any idea? You can see the code on this post. Edit: Here's the important part of the code: package com.bluecubs.xinco.core.server.vaadin; import com.bluecubs.xinco.core.server.XincoConfigSingletonServer; import com.vaadin.Application; import com.vaadin.terminal.DownloadStream; import com.vaadin.terminal.FileResource; import java.io.*; import java.net.URLEncoder; import java.util.UUID; import java.util.logging.Level; import java.util.logging.Logger; import java.util.zip.CRC32; import java.util.zip.CheckedInputStream; /** * * @author Javier A. Ortiz Bultrón<[email protected]> */ public class FileDownloadResource extends FileResource { private final String fileName; private File download; private File newFile; public FileDownloadResource(File sourceFile, String fileName, Application application) { super(sourceFile, application); this.fileName = fileName; } protected void cleanup() { if (newFile != null && newFile.exists()) { newFile.delete(); } if (download != null && download.exists() && download.listFiles().length == 0) { download.delete(); } } @Override public DownloadStream getStream() { try { //Copy file to directory for downloading InputStream in = new CheckedInputStream(new FileInputStream(getSourceFile()), new CRC32()); download = new File(XincoConfigSingletonServer.getInstance().FileRepositoryPath + System.getProperty("file.separator") + UUID.randomUUID().toString()); newFile = new File(download.getAbsolutePath() + System.getProperty("file.separator") + fileName); download.mkdirs(); OutputStream out = new FileOutputStream(newFile); newFile.deleteOnExit(); download.deleteOnExit(); byte[] buf = new byte[1024]; int len; while ((len = in.read(buf)) > 0) { out.write(buf, 0, len); } in.close(); out.close(); final DownloadStream ds = new DownloadStream( new FileInputStream(newFile), getMIMEType(), fileName); ds.setParameter("Content-Disposition", "attachment; filename=" + URLEncoder.encode(fileName, "utf-8")); ds.setCacheTime(getCacheTime()); return ds; } catch (final FileNotFoundException ex) { Logger.getLogger(FileDownloadResource.class.getName()).log(Level.SEVERE, null, ex); return null; } catch (IOException ex) { Logger.getLogger(FileDownloadResource.class.getName()).log(Level.SEVERE, null, ex); return null; } } } I already debugged and verified that fileName only contains the file's name not the whole path.

  Read the article

• Should I throw my own ArgumentOutOfRangeException or let one bubble up from below?

  - by Neil N

  I have a class that wraps List< I have GetValue by index method: public RenderedImageInfo GetValue(int index) { list[index].LastRetrieved = DateTime.Now; return list[index]; } If the user requests an index that is out of range, this will throw an ArgumentOutOfRangeException . Should I just let this happen or check for it and throw my own? i.e. public RenderedImageInfo GetValue(int index) { if (index >= list.Count) { throw new ArgumentOutOfRangeException("index"); } list[index].LastRetrieved = DateTime.Now; return list[index]; } In the first scenario, the user would have an exception from the internal list, which breaks mt OOP goal of the user not needing to know about the underlying objects. But in the second scenario, I feel as though I am adding redundant code. Edit: And now that I think of it, what about a 3rd scenario, where I catch the internal exception, modify it, and rethrow it?

  Read the article

• android camera preview blank screen

  - by user1104836

  I want to capture a photo manually not by using existing camera apps. So i made this Activity: public class CameraActivity extends Activity { private Camera mCamera; private Preview mPreview; @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_camera); // Create an instance of Camera // mCamera = Camera.open(0); // Create our Preview view and set it as the content of our activity. mPreview = new Preview(this); mPreview.safeCameraOpen(0); FrameLayout preview = (FrameLayout) findViewById(R.id.camera_preview); preview.addView(mPreview); } @Override public boolean onCreateOptionsMenu(Menu menu) { // Inflate the menu; this adds items to the action bar if it is present. getMenuInflater().inflate(R.menu.activity_camera, menu); return true; } } This is the CameraPreview which i want to use: public class Preview extends ViewGroup implements SurfaceHolder.Callback { SurfaceView mSurfaceView; SurfaceHolder mHolder; //CAM INSTANCE ================================ private Camera mCamera; List<Size> mSupportedPreviewSizes; //============================================= /** * @param context */ public Preview(Context context) { super(context); mSurfaceView = new SurfaceView(context); addView(mSurfaceView); // Install a SurfaceHolder.Callback so we get notified when the // underlying surface is created and destroyed. mHolder = mSurfaceView.getHolder(); mHolder.addCallback(this); mHolder.setType(SurfaceHolder.SURFACE_TYPE_PUSH_BUFFERS); } /** * @param context * @param attrs */ public Preview(Context context, AttributeSet attrs) { super(context, attrs); // TODO Auto-generated constructor stub } /** * @param context * @param attrs * @param defStyle */ public Preview(Context context, AttributeSet attrs, int defStyle) { super(context, attrs, defStyle); // TODO Auto-generated constructor stub } /* (non-Javadoc) * @see android.view.ViewGroup#onLayout(boolean, int, int, int, int) */ @Override protected void onLayout(boolean arg0, int arg1, int arg2, int arg3, int arg4) { // TODO Auto-generated method stub } @Override public void surfaceChanged(SurfaceHolder holder, int format, int width, int height) { // Now that the size is known, set up the camera parameters and begin // the preview. Camera.Parameters parameters = mCamera.getParameters(); parameters.setPreviewSize(width, height); requestLayout(); mCamera.setParameters(parameters); /* Important: Call startPreview() to start updating the preview surface. Preview must be started before you can take a picture. */ mCamera.startPreview(); } @Override public void surfaceCreated(SurfaceHolder holder) { // TODO Auto-generated method stub } @Override public void surfaceDestroyed(SurfaceHolder holder) { // Surface will be destroyed when we return, so stop the preview. if (mCamera != null) { /* Call stopPreview() to stop updating the preview surface. */ mCamera.stopPreview(); } } /** * When this function returns, mCamera will be null. */ private void stopPreviewAndFreeCamera() { if (mCamera != null) { /* Call stopPreview() to stop updating the preview surface. */ mCamera.stopPreview(); /* Important: Call release() to release the camera for use by other applications. Applications should release the camera immediately in onPause() (and re-open() it in onResume()). */ mCamera.release(); mCamera = null; } } public void setCamera(Camera camera) { if (mCamera == camera) { return; } stopPreviewAndFreeCamera(); mCamera = camera; if (mCamera != null) { List<Size> localSizes = mCamera.getParameters().getSupportedPreviewSizes(); mSupportedPreviewSizes = localSizes; requestLayout(); try { mCamera.setPreviewDisplay(mHolder); } catch (IOException e) { e.printStackTrace(); } /* Important: Call startPreview() to start updating the preview surface. Preview must be started before you can take a picture. */ mCamera.startPreview(); } } public boolean safeCameraOpen(int id) { boolean qOpened = false; try { releaseCameraAndPreview(); mCamera = Camera.open(id); mCamera.startPreview(); qOpened = (mCamera != null); } catch (Exception e) { // Log.e(R.string.app_name, "failed to open Camera"); e.printStackTrace(); } return qOpened; } Camera.PictureCallback mPicCallback = new Camera.PictureCallback() { @Override public void onPictureTaken(byte[] data, Camera camera) { // TODO Auto-generated method stub Log.d("lala", "pic is taken"); } }; public void takePic() { mCamera.startPreview(); // mCamera.takePicture(null, mPicCallback, mPicCallback); } private void releaseCameraAndPreview() { this.setCamera(null); if (mCamera != null) { mCamera.release(); mCamera = null; } } } This is the Layout of CameraActivity: <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" xmlns:tools="http://schemas.android.com/tools" android:layout_width="match_parent" android:layout_height="match_parent" tools:context=".CameraActivity" > <FrameLayout android:id="@+id/camera_preview" android:layout_width="0dip" android:layout_height="fill_parent" android:layout_weight="1" /> <Button android:id="@+id/button_capture" android:text="Capture" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_gravity="center" /> </LinearLayout> But when i start the CameraActivity, i just see a blank white background and the Capture-Button??? Why i dont see the Camera-Screen?

  Read the article

• boost multi_index_container and erase performance

  - by rjoshi

  I have a boost multi_index_container declared as below which is indexed by hash_unique id(unsigned long) and hash_non_unique transaction id(long). Insertion and retrieval of elements is fast but when I delete elements, it is much slower. I was expecting it to be constant time as key is hashed. e.g To erase elements from container for 10,000 elements, it takes around 2.53927016 seconds for 15,000 elements, it takes around 7.137100068 seconds for 20,000 elements, it takes around 21.391720757 seconds Is it something I am missing or is it expected behavior? class Session { public: Session() { //increment unique id static unsigned long counter = 0; boost::mutex::scoped_lock guard(mx); counter++; m_nId = counter; } unsigned long GetId() { return m_nId; } long GetTransactionHandle(){ return m_nTransactionHandle; } .... private: unsigned long m_nId; long m_nTransactionHandle; boost::mutext mx; .... }; typedef multi_index_container< Session*, indexed_by< hashed_unique< mem_fun<Session,unsigned long,&Session::GetId> >, hashed_non_unique< mem_fun<Session,unsigned long,&Session::GetTransactionHandle> > > //end indexed_by > SessionContainer; typedef SessionContainer::nth_index<0>::type SessionById; int main() { ... SessionContainer container; SessionById *pSessionIdView = &get<0>(container); unsigned counter = atoi(argv[1]); vector<Session*> vSes(counter); //insert for(unsigned i = 0; i < counter; i++) { Session *pSes = new Session(); container.insert(pSes); vSes.push_back(pSes); } timespec ts; lock_settime(CLOCK_PROCESS_CPUTIME_ID, &ts); //erase for(unsigned i = 0; i < counter; i++) { pSessionIdView->erase(vSes[i]->getId()); delete vSes[i]; } lock_gettime(CLOCK_PROCESS_CPUTIME_ID, &ts); std::cout << "Total time taken for erase:" << ts.tv_sec << "." << ts.tv_nsec << "\n"; return (EXIST_SUCCESS); }

  Read the article

• jQuery Validation Engine with Mime

  - by Diego Pucci

  I have this custom rule with tje jQuery validation Engine: "validateMIME": { "func": function(field, rules, i, options){ var fileInput = field[0].files[0]; var MimeFilter = new RegExp(rules[3],'i'); if (fileInput) { return MimeFilter.test(fileInput.type); } else { return true;} }, "alertText": "* Estensione non supportata" }, The problem is that this is working ONLY if the field is required. But in my case the field is not required, but if filled then the Mime type needs to be checked. How do I edit this function to work with non required fields? what's wrong with it? Thanks

  Read the article

• creating my own context processor in django

  - by dotty

  Hay, I have come to a point where i need to pass certain variables to all my views (mostly custom authentication type variables). I was told writing my own context processor was the best way to do this, but i am having some issues. My settings file looks like this TEMPLATE_CONTEXT_PROCESSORS = ( "django.contrib.auth.context_processors.auth", "django.core.context_processors.debug", "django.core.context_processors.i18n", "django.core.context_processors.media", "django.contrib.messages.context_processors.messages", "sandbox.context_processors.say_hello", ) As you can see i have a module called 'context_processors' and a function within that called 'say_hello'. This looks like def say_hello(request): return { 'say_hello':"Hello", } Am i right to assume i can now do this within my views {{ say_hello }} because it doesn't return anything.

  Read the article

• CakePHP dynamic element

  - by Logic Artist

  I am trying to create a message-board type element in a CakePHP app. This element will be displayed on all pages and views that use a particular layout. I want it to display all the messages in the model, then show the add form when a link is clicked, then return to the updated message list when submitted. All this without affecting the current view/page. I have my message model/controller/index set up, with a message board element that requests the index action. This works fine. However I am perplexed about how to return back to the original page/action from which the link was clicked. I can't use $this-referer() because that will link back to the add() action; what I want rather is to link to the page/view before that. Any general pointers on how to achieve something like this?

  Read the article

• jQuery Tabs - Following External Links

  - by Ricky

  I have jQuery Tabs setup, but am trying to get a Tab to follow an external link. I have tried to use the code from jQuery, but the URL still loads via Ajax instead of redirecting the browser to the url: http://jqueryui.com/demos/tabs/#...follow_a_tab.27s_URL_instead_of_loading_its_content_via_ajax Current code: $(function() { $('#rotate > ul').tabs({ select: function(event, ui) { var url = $.data(ui.tab, 'load.tabs'); if( url ) { location.href = url; return false; } return true; } }); });

  Read the article

• How can I make Swig correctly wrap a char* buffer that is modified in C as a Java Something-or-other

  - by Ukko

  I am trying to wrap some legacy code for use in Java and I was quite happy to see that Swig was able to handle the header file and it generate a great wrapper that almost works. Now I am looking for the deep magic that will make it really work. In C I have a function that looks like this DLL_IMPORT int DustyVoodoo(char *buff, int len, char *curse); This integer returned by this function is an error code in case it fails. The arguments are buff is a character buffer len is the length of the data in the buffer curse the another character buffer that contains the result of calling DustyVoodoo So, you can see where this is going, the result is actually coming back via the third argument. Also len is confusing since it may be the length of both buffers, they are always allocated as being the same size in calling code but given what DustyVoodoo does I don't think that they need be the same. To be safe both buffers should be the same size in practice, say 512 chars. The C code generated for the binding is as follows: SWIGEXPORT jint JNICALL Java_pemapiJNI_DustyVoodoo(JNIEnv *jenv, jclass jcls, jstring jarg1, jint jarg2, jstring jarg3) { jint jresult = 0 ; char *arg1 = (char *) 0 ; int arg2 ; char *arg3 = (char *) 0 ; int result; (void)jenv; (void)jcls; arg1 = 0; if (jarg1) { arg1 = (char *)(*jenv)->GetStringUTFChars(jenv, jarg1, 0); if (!arg1) return 0; } arg2 = (int)jarg2; arg3 = 0; if (jarg3) { arg3 = (char *)(*jenv)->GetStringUTFChars(jenv, jarg3, 0); if (!arg3) return 0; } result = (int)PemnEncrypt(arg1,arg2,arg3); jresult = (jint)result; if (arg1) (*jenv)->ReleaseStringUTFChars(jenv, jarg1, (const char *)arg1); if (arg3) (*jenv)->ReleaseStringUTFChars(jenv, jarg3, (const char *)arg3); return jresult; } It is correct for what it does; however, it misses the fact that cursed is not just an input, it is altered by the function and should be returned as an output. It also does not know that the java Strings are really buffers and should be backed by a suitably sized array. I think that Swig can do the right thing here, I just can't figure out from the documentation how to tell Swig what it needs to know. Any typemap masers in the house?

  Read the article

• Grabbing random object from ArrayList is not random.

  - by Isai

  I am creating a method where if you pass in a parameter of type Random, then it will return a random object. Here is basically what I am trying to do: public T choose(Random r) { int randomInt = r.nextInt(randomList.size()); // randomList is just a instance variable return randomList.get(randomInt); } The random list has this the following strings:[2, 2, 2, 1, 1, 1, 1, c, c, c, a, a, a, a] Then I made a driver with the following code for (int i = 0; i < 10; i++) { System.out.print(rndList.choose(rnd)); // rnd is initialized as a static Random variable } However my outputs are not coming out random. I used the debugger and found out that my choose method generates an integer that is relatively low, so it will always print out either 2's or 1's but never c's or a's. I can't figure out why this is happening and help would be greatly appreciated.

  Read the article

• Call to C++ COM interface from C# being blocked

  - by dauphic

  I have a C++ DLL that exposes a COM interface. A C# application uses the COM interface. I've recently run into a problem where some calls to the COM interface are taking 500-5000 ms to return, though they should return almost instantly (no longer than 10 ms). Profiling the application shows that all of the delay is being caused by the 'thread being blocked;' no other information is available. There are no locks, etc. in my code, so the blocking has to be occurring internally in the COM/interop code. Only one thread interfaces with the COM DLL. Any ideas what could be causing this, and how I would fix it? EDIT: Further investigation shows that the block is occuring when the C++ returns to the C#.

  Read the article

• jquery plugin with multiple functions

  - by tcurdt

  According to the developer documentation jquery plugins are supposed to have only one namespace for all functions they make available. Which is straight forward as long as you only expose a single function per context (static/element). (function($){ var state_a = 0, $.myplugin = function(in_options) { // static return this; } $.fn.myplugin = function(in_options) { // element return this; } })(jQuery); This makes calls like this possible: $("elem").myplugin(options); jQuery.myplugin(options); What's the best approach if you have more than one function and need to share state? I would like to call into my plugin like this: $("elem").myplugin.start(options); $("elem").myplugin.stop(); jQuery.myplugin.start(options); jQuery.myplugin.stop();

  Read the article

• In Google App Engine, what is the simplest way to keep a record of items that you have put into memc

  - by Chris Boesch

  I am starting to use memcache more frequently to avoid having to recalculate things between page requests. When the memcache periodically clears, as it is designed to do, I have to start all over rebuilding various items that I have placed in memcache. What I would like to do is create a very simple model that enables me to periodically save the items that I put into memcache based on the memcache keys that I'm using along with a datetime that is related to the data being memcached. What is the best way to do this? I'm looking for something like this: class MemcacheRecord(db.Model): key = db.StringProperty(required=True) value = #Something that can store whatever memcache can validThru = db.DateTimeProperty(required=True) def set(self, key, value, validThru): #Save a new memcache record newMemcacheRecord = MemcacheRecord(key=key, value=value, validThru=validThru) .. return True # or False def get_latest(self, key): #Get the memcache record with the most recent validThru datetime latestMemcacheRecord = MemcacheRecord.all().order('-validThru').get() return {'validThru':latestMemcacheRecord.validThru, 'value':latestMemcachRecord.value}

  Read the article

• What is the most efficiant way to get the highest and the lowest value in a Array

  - by meo

  is there something like PHP: max() in javascript? lets say i have an array like this: [2, 3, 23, 2, 2345, 4, 86, 8, 231, 75] and i want to return the highest and the lowest value in this array. What is the fastest way to do that? i have tried: function madmax (arr) { var max = arr[0], min = arr[1] if (min > max) { max = arr[1] min = arr[0] } for (i=1;i<=arr.length;i++){ if( arr[i] > max ) { max = arr[i] }else if( arr[i] < min ) { min = arr[i] } } return max, min } madmax([123, 2, 345, 153, 5, 98, 456, 4323456, 1, 234, 19874, 238, 4]) Is there a simpler way retrieve the max and min value of a array?

  Read the article

• my version of strlcpy

  - by robUK

  Hello, gcc 4.4.4 c89 My program does a lot of string coping. I don't want to use the strncpy as it doesn't nul terminate. And I can't use strlcpy as its not portable. Just a few questions. How can I put my function those its paces to ensure that it is completely safe and stable. Unit testing? Is this good enough for production? size_t s_strlcpy(char *dest, const char *src, const size_t len) { size_t i = 0; /* Always copy 1 less then the destination to make room for the nul */ for(i = 0; i < len - 1; i++) { /* only copy up to the first nul is reached */ if(*src != '\0') { *dest++ = *src++; } else { break; } } /* nul terminate the string */ *dest = '\0'; /* Return the number of bytes copied */ return i; } Many thanks for any suggestions,

  Read the article

• Floor function returning EXC_BAD_ACCESS

  - by fastrack20

  The cod that I am using contains these snippets of code. I am calling ThetaG_JD with the argument 2455343.50000 which is just a sample Julian date. Every time I run the program, I receive a EXC_BAD_ACCESS on the indicated line. When using gdb and printing out the intermediary values and passing them through the floor function, I get no error, but when Frac() is used it always returns an error. double Frac(double arg) { /* Returns fractional part of double argument */ return arg - floor(arg); } double ThetaG_JD(double jd) { /* Reference: The 1992 Astronomical Almanac, page B6. */ double UT=0, TU=0, GMST=0; //THIS LINE UT=Frac(jd+0.5); // THAT ONE ^^ jd=jd-UT; TU=(jd-2451545.0)/36525; GMST=24110.54841+TU*(8640184.812866+TU*(0.093104-TU*6.2E-6)); GMST=Modulus(GMST+secday*omega_E*UT,secday); return (twopi*GMST/secday); }

  Read the article

• Is it possible to create a new T-SQL Operator using CLR Code in MSSQL?

  - by Eoin Campbell

  I have a very simple CLR Function for doing Regex Matching public static SqlBoolean RegExMatch(SqlString input, SqlString pattern) { if (input.IsNull || pattern.IsNull) return SqlBoolean.False; return Regex.IsMatch(input.Value, pattern.Value, RegexOptions.IgnoreCase); } It allows me to write a SQL Statement Like. SELECT * FROM dbo.table1 WHERE dbo.RegexMatch(column1, '[0-9][A-Z]') = 1 -- match entries in col1 like 1A, 2B etc... I'm just thinking it would be nice to reformulate that query so it could be called like SELECT * FROM dbo.table1 WHERE column1 REGEXLIKE '[0-9][A-Z]' Is it possible to create new comparison operators using CLR Code. (I'm guessing from my brief glance around the web that the answer is NO, but no harm asking) Thanks, Eoin C

  Read the article

• Order by descending based on condition

  - by Vinni

  Hello All, I want to write a LINQ to Entity query which does order by ascending or descending based on input parameter, Is there any way for that. Following is the my code. Please suggest. public List<Hosters_HostingProviderDetail> GetPendingApproval(SortOrder sortOrder) { List<Hosters_HostingProviderDetail> returnList = new List<Hosters_HostingProviderDetail>(); int pendingStateId = Convert.ToInt32(State.Pending); //If the sort order is ascending if (sortOrder == SortOrder.ASC) { var hosters = from e in context.Hosters_HostingProviderDetail where e.ActiveStatusID == pendingStateId orderby e.HostingProviderName ascending select e; returnList = hosters.ToList<Hosters_HostingProviderDetail>(); return returnList; } else { var hosters = from e in context.Hosters_HostingProviderDetail where e.StateID == pendingStateId orderby e.HostingProviderName descending select e; returnList = hosters.ToList<Hosters_HostingProviderDetail>(); return returnList; } }

  Read the article

• Chain LINQ IQueryable, and end with Stored Procedure

  - by Alex

  I'm chaining search criteria in my application through IQueryable extension methods, e.g.: public static IQueryable<Fish> AtAge (this IQueryable<Fish> fish, Int32 age) { return fish.Where(f => f.Age == age); } However, I also have a full text search stored procedure: CREATE PROCEDURE [dbo].[Fishes_FullTextSearch] @searchtext nvarchar(4000), @limitcount int AS SELECT Fishes.* FROM Fishes INNER JOIN CONTAINSTABLE(Fishes, *, @searchtext, @limitcount) AS KEY_TBL ON Fishes.Id = KEY_TBL.[KEY] ORDER BY KEY_TBL.[Rank] The stored procedure obviously doesn't return IQueryable, however, is it possible to somehow limit the result set for the stored procedure using IQueryable's? I'm envisioning something like .AtAge(5).AboveWeight(100).Fishes_FulltextSearch("abc"). In this case, the fulltext search should execute on a smaller subset of my Fishes table (narrowed by Age and Weight). Is something like this possible? Sample code?

  Read the article

• Problem updating blog with hibernate?

  - by johnsmith51

  hi, i am having problem updating a blob with hibernate. my model have these getters/setters for hibernate, i.e. internally i deal with byte[] so any getter/setter convert the byte[] to blog. I can create an initial object without problem, but if I try to change the content of the blob, the database column is not updated. I do not get any error message, everything looks fine, except that the database is not updated. /** do not use, for hibernate only */ public Blob getLogoBinaryBlob() { if(logoBinary == null){ return null; } return Hibernate.createBlob(logoBinary); } /** do not use, for hibernate only */ public void setLogoBinaryBlob(Blob logoBinaryBlob) { ByteArrayOutputStream baos = new ByteArrayOutputStream(); try { logoBinary = toByteArrayImpl(logoBinaryBlob, baos); } catch (Exception e) { } }

  Read the article

• Why is this the output of this python program?

  - by Andrew Moffat

  Someone from #python suggested that it's searching for module "herpaderp" and finding all the ones listed as its searching. If this is the case, why doesn't it list every module on my system before raising ImportError? Can someone shed some light on what's happening here? import sys class TempLoader(object): def __init__(self, path_entry): if path_entry == 'test': return raise ImportError def find_module(self, fullname, path=None): print fullname, path return None sys.path.insert(0, 'test') sys.path_hooks.append(TempLoader) import herpaderp output: 16:00:55 $> python wtf.py herpaderp None apport None subprocess None traceback None pickle None struct None re None sre_compile None sre_parse None sre_constants None org None tempfile None random None __future__ None urllib None string None socket None _ssl None urlparse None collections None keyword None ssl None textwrap None base64 None fnmatch None glob None atexit None xml None _xmlplus None copy None org None pyexpat None problem_report None gzip None email None quopri None uu None unittest None ConfigParser None shutil None apt None apt_pkg None gettext None locale None functools None httplib None mimetools None rfc822 None urllib2 None hashlib None _hashlib None bisect None Traceback (most recent call last): File "wtf.py", line 14, in <module> import herpaderp ImportError: No module named herpaderp

  Read the article

• How this is code is getting compiled even though we are using a constant which is defined later?

  - by GK

  In the following code DEFAULT_CACHE_SIZE is declared later, but it is used to assign a value to String variable before than that, so was curious how is it possible? public class Test { public String getName() { return this.name; } public int getCacheSize() { return this.cacheSize; } public synchronized void setCacheSize(int size) { this.cacheSize = size; System.out.println("Cache size now " + this.cacheSize); } private final String name = "Reginald"; private int cacheSize = DEFAULT_CACHE_SIZE; private static final int DEFAULT_CACHE_SIZE = 200; }

  Read the article

• JPA One To Many Relationship Persistence Bug

  - by Brian

  Hey folks, I've got a really weird problem with a bi-directional relationship in jpa (hibernate implementation). A User is based in one Region, and a Region can contain many Users. So...relationship is as follows: Region object: @OneToMany(mappedBy = "region", fetch = FetchType.LAZY, cascade = CascadeType.ALL) public Set<User> getUsers() { return users; } public void setUsers(Set<User> users) { this.users = users; } User object: @ManyToOne(cascade = {CascadeType.PERSIST, CascadeType.MERGE}, fetch = FetchType.EAGER) @JoinColumn(name = "region_fk") public Region getRegion() { return region; } public void setRegion(Region region) { this.region = region; } So, the relationship as you can see above is Lazy on the region side, ie, I don't want the region to eager load all the users. Therefore, I have the following code within my DAO layer to add a user to an existing user to an existing region object... public User setRegionForUser(String username, Long regionId){ Region r = (Region) this.get(Region.class, regionId); User u = (User) this.get(User.class, username); u.setRegion(r); Set<User> users = r.getUsers(); users.add(u); System.out.println("The number of users in the set is: "+users.size()); r.setUsers(users); this.update(r); return (User)this.update(u); } The problem is, when I run a little unit test to add 5 users to my region object, I see that the region.getUsers() set always stays stuck at 1 object...somehow the set isn't getting added to. My unit test code is as follows: public void setUp(){ System.out.println("calling setup method"); Region r = (Region)ManagerFactory.getCountryAndRegionManager().get(Region.class, Long.valueOf("2")); for(int i = 0; i<loop; i++){ User u = new User(); u.setUsername("username_"+i); ManagerFactory.getUserManager().update(u); ManagerFactory.getUserManager().setRegionForUser("username_"+i, Long.valueOf("2")); } } public void tearDown(){ System.out.println("calling teardown method"); for(int i = 0; i<loop; i++){ ManagerFactory.getUserManager().deleteUser("username_"+i); } } public void testGetUsersForRegion(){ Set<User> totalUsers = ManagerFactory.getCountryAndRegionManager().getUsersInRegion(Long.valueOf("2")); System.out.println("Expecting 5, got: "+totalUsers.size()); this.assertEquals(5, totalUsers.size()); } So the test keeps failing saying there is only 1 user instead of the expected 5. Any ideas what I'm doing wrong? thanks very much, Brian

  Read the article

• How do i use repoze.who?

  - by misterwebz

  I'm having some trouble understanding how repoze.who works. I've followed a tutorial i found by searching on google and here's what i already have: This is what i added in my middleware.py file from repoze.who.config import make_middleware_with_config as make_who_with_config app = make_who_with_config(app, global_conf, app_conf['who.config_file'], app_conf['who.log_file'], app_conf['who.log_level']) Here's the who.ini : http://pastebin.com/w5Tba2Fp Here's repoze_auth.py in /lib/auth/: from paste.httpexceptions import HTTPFound from iwant.model import User class UserModelPlugin(object): def authenticate(self, environ, identity): try: username = identity['login'] password = identity['password'] except KeyError: return None success = User.authenticate(username, password) return success def add_metadata(self, environ, identity): username = identity.get('repoze.who.userid') user = User.get(username) if user is not None: identity['user'] = user I've also checked the plugins in the repoze.who folder, but i failed to understand how it's supposed to be used. I'd appreciate it if someone would push me in the right direction.

  Read the article

< Previous Page | 366 367 368 369 370 371 372 373 374 375 376 377  | Next Page >