Search Results

Search found 12083 results on 484 pages for 'general purpose'.

Page 378/484 | < Previous Page | 374 375 376 377 378 379 380 381 382 383 384 385  | Next Page >

• Redirection of outbound UDP port.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. I tried, but can't seem to get iptables to do what I want. I'm not sure if it's my lack of skill, or if I'm trying the wrong solution. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• When modern computers boot, what initial setup of RAM do they execute, and how does it exactly work?

  - by user272840

  I know the title reeks of confusion, and some of you might assume I am just wondering about how the computer boots in general, but I'm not. But I'll sort this out for you people now: 1.Onboard firmware is how mostly all modern computer devices work, whether or not with EFI/UEFI(even without "onboard firmware", older computers still employed bank switching, or similar methods with snap-in firmware, cartridges, etc.) 2.On startup there is no "programs" running in the traditional sense yet, i.e. no kernel, OS, user-applications; all of the instructions, especially the very first instruction, is specified by the Instruction Pointer, I am guessing. How is the IP/PC/etc. set to first point to an address for a BIOS/firmware/etc. instruction, and how do the BIOS instructions map themself out in memory prior to startup? 3.Aside from MMIO, BIOS uses certain RAM addresses to have instructions. The big ? comes in when I ask this ... how does BIOS do this? Conclusion: I am assuming that with the very first instruction there is an initial hardware setup for BIOS prior to complete OS bootup. What I want to know is if it's hardware engineered to always work this way, if there's another step in this bootup method I am missing, a gap of information I am unaware of, or how this all works from the very first instruction, and the RAM data itself.

  Read the article

• How to setup the Mac OS X Terminal so it's *just peachy*?

  - by kch

  Hi all, My Terminal is awesome, has every detail just right (for me anyway), and now I'm setting up a few new macs around here and I have no idea whatsoever how to get their terminals to a pretty state. My user account is rather old, has been migrated over many OS X releases and machines, so my Terminal setup has grown rather organically over the years. What I need is a recipe to start from scratch, so 1) I know what I've done, and 2) I can reproduce it anywhere. Things I'm looking for: Full UTF8 support. Setting LC_*, displaying characters correctly, accepting input… I hear this got much easier in 10.5, maybe it all works out of the box now? Setup of OS X-style keyboard text navigation (option-arrows, etc) How you particularly handle meta-key support? (other than ESC'ing your way around) Other things to help our n00bs get around in the shell, such as: List of useful default key bindings (^A, ^D, etc…) Mac-specific .profile, .inputrc goodness Mac-specific tools such as pbpaste & pbcopy, Open Terminal Here, etc If at all possible, a list of files to copy over to another machine that encompasses all the changes made to tune the Terminal. (dotrc files, plists, etc) And, well, anything else really. Just keep the scope on the Mac OS X Terminal application, rather than general unix setup and tools. I think a collection of incomplete answers would be a good start. Post one or two things you remember having done, we'll vote them up, and after a few days I'll try to compile it all into a summary answer.

  Read the article

• VirtualBox how to merge arbitrary snapshot into base vdi

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID? Thanks

  Read the article

• Looking for an application that scrolls or pans netbook screens running Windows

  - by therobyouknow

  I'm looking for a Windows 7 and XP compatible Windows desktop panning/scrolling tool. This is to solve a problem where some applications for example MSN have settings/preference Windows that are not resizeable. I have a Netbook with a small maximum screen resolution e.g. 1024x600. The fixed non-resizeable windows are too large for this display screen size so I cannot see all of the items on these windows, particularly the OK button to save settings. What I would like is a desktop scrolling/panning tool where if I move my mouse pointer to any edge of the display, it pans to show the region of the too-large-fixed window that I could not see. I use a Samsung N110 and Toshiba NB100 netbooks. I'm looking for: A general program that provides desktop panning/scrolling/expanded resolution to allow all regions of a non-resizeable fixed window Preferably a non-graphics hardware specific program but will accept a solution that works with both the above machines I'm NOT looking for (i.e. unsatisfactory answers others have asked that I've already searched and found): Advice on what programs to use that DON'T have the problem of fixed windows Alternative operating system solutions Plugging in an external monitor with larger resolution - I use this option but I need a solution when one is not available, e.g. while travelling etc Advice about not using small screen netbooks - I enjoy the compact convenience of them Advice about change the dpi settings in the Control Panel Display settings Advice about guesswork with the tab key to move the focus the off-screen item I cannot see Thank you in advance.

  Read the article

• What format should I convert my iTunes Videos to?

  - by Aequitarum Custos

  Recently got Daniusoft Media Converter, and was about to strip the DRM off my iTunes library, then I found I had a huge decision to make. Converting my music seems obvious, to MP3, however the video formats, I'm at a loss on. It has "optimized" formats for all types of video players such as iPhone, Zune, Droid (which I own), and just a huge list! I bought several seasons of House and a few movies, though I don't know which format would be optimal to not lose quality. While I love my Droid, I have no intention on watching full episodes or movies on it, and I have a feeling that would reduce quality. One of the options sections is HD Video, and it has HD MPEG-4 Video (*.mp4). That one seems like it would be the best format to convert to without losing quality, but again, I'm unsure. Has anyone used this software, or have general expertise in video formats to give a recommendation on what file format I should convert my videos to? Format requirements: No loss in quality Portability would be ideal (as in, will play on my Windows and potentially MAC, and streamable to a bigscreen).

  Read the article

• 7ZIP - Command Line Compression | Can Never Keep it Simple

  - by OneTwoYou

  I've been Googleing for a few hours on how to just compress a file inside a directory and I can't find anything. I found how to just compress a folder in general. Now I wish to know how I can compress a folder in a folder with a file. Current code: 7zG.exe a -tzip "test.zip" dontcompressme/compressme/new.txt pause As you can see above, I don't want to compress the first folder, but only the second and what ever is within that folder. I have the 7zG.exe sitting in the main folder and I have some files that are three folders in, but I don't know how to only compress those. Here is my directory list: Folder One (don't compress) Folder Two (don't compress) Folder Three (okay to compress) Document One.txt (okay to compress) Document Two.txt (okay to compress) Index.html (okay to compress) Does anyone know how I can do this in the most simplest way ever invented by man? Cause whenever I go to a website using Google it goes throw all these methods on how to compress a folder, but not do it the way I wish it to do. It makes me kinda upset cause I can't get a simple and straight forward answer. Thank you if you answer my question.

  Read the article

• How to autorun wpa_supplicant on Debian startup

  - by The Electric Muffin

  I'd like to run wpa_supplicant -D wext -i wlan0 -c /etc/wpa_supplicant.conf on Debian startup (runlevels 2-5). I found some vague instructions from a related question that said to put a script in /etc/init.d/ and then symlink to it from the apropriate /etc/rcRUNLEVEL.d/ directories. However, I noticed that there are already some files named "wpasupplicant" that probably run at startup: /etc/network/if-down.d/wpasupplicant /etc/network/if-post-down.d/wpasupplicant /etc/network/if-pre-up.d/wpasupplicant /etc/network/if-up.d/wpasupplicant They all are symlinks to the same script, /etc/wpa_supplicant/ifupdown.sh. It has a comment at the beginning saying it "[...] allows ifup(8), and ifdown(8) to manage wpa_supplicant(8) and wpa_cli(8) processes running in daemon mode." However, the closest it gets to calling wpa_supplicant itself is (in functions.sh): WPA_SUP_BIN="/sbin/wpa_supplicant" [snip] start-stop-daemon --start --oknodo $DAEMON_VERBOSITY \ --name $WPA_SUP_PNAME --startas $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE \ -- $WPA_SUP_OPTIONS $WPA_SUP_CONF [snip] start-stop-daemon --stop --oknodo $DAEMON_VERBOSITY \ --exec $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE Does that mean it's safe to make an init.d script for wpa_supplicant, and if so what would it look like? General info: Debian Squeeze (5.0) official wpasupplicant package (v0.6.10-2.1) The full contents of my system's functions.sh and ifupdown.sh are here (dependent, of course, on my system's uptime—it's a five-year-old laptop that greatly enjoys overheating): functions.sh ifupdown.sh

  Read the article

• Having two IP Routes/Gateways of last Resort on an HP Switch

  - by SteadH

  We have an HP Layer 3 Switch that is doing IP routing between vlans. The general set up is that the switch has an IP address on each VLAN and IP routing is enabled. On our servers VLAN, we have a firewall that has a connection to the outside world. To set a IP route on the HP router, we use IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.1 where 192.168.2.1 is the address of our firewall, and the zeros essentially mean to route all traffic that the switch doesn't know what to do with out the firewall as a gateway. We're in the middle of an ISP and firewall change. I set up the new firewall and ran the IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.254 (the address of the new firewall). Things started working nicely. When I reviewed the configuration of the switch though, I noticed that it did not replace the previous ip route command, but just added another route. Now, I know how to remove the old firewall route (no ip route 0.0.0.0 0.0.0.0 192.168.2.1), but what is the effect of having these two 0.0.0.0 routes? Is it switch implosion? Will a server just respond back over the route it receives the request from? I've read elsewhere that having two default gateways is an impossibility by definition, but I'm curious about this situation that our switch allowed. Thanks!

  Read the article

• Macports install of ack doesn't create correct executable

  - by user1664196

  I am trying to install p5-app-ack port from Mac Ports, but it seems it doesn't create a /opt/local/bin/ack binary at the end: $ sudo port search *app-ack Password: p5-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.8-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.10-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.12-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.14-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.16-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories Found 6 ports. $ perl --version This is perl 5, version 12, subversion 4 (v5.12.4) built for darwin-thread-multi-2level Copyright 1987-2010, Larry Wall Perl may be copied only under the terms of either the Artistic License or the GNU General Public License, which may be found in the Perl 5 source kit. Complete documentation for Perl, including FAQ lists, should be found on this system using "man perl" or "perldoc perl". If you have access to the Internet, point your browser at http://www.perl.org/, the Perl Home Page. $ sudo port install p5-app-ack ---> Computing dependencies for p5-app-ack ---> Cleaning p5-app-ack ---> Updating database of binaries: 100.0% ---> Scanning binaries for linking errors: 35.0% ---> No broken files found. $ $ ls /opt/local/bin/ac* /opt/local/bin/ack-5.12 /opt/local/bin/aclocal /opt/local/bin/aclocal-1.12 /opt/local/bin/activation-client /opt/local/bin/acyclic $ which ack $ ack -bash: ack: command not found Update If I then try to install p5.12-app-ack afterwards, I get $ sudo port install p5.12-app-ack Password: ---> Computing dependencies for p5.12-app-ack ---> Cleaning p5.12-app-ack ---> Scanning binaries for linking errors: 100.0% ---> No broken files found. $

  Read the article

• Viewing Postscript (or PDF) on OS X: Aliasing issues

  - by mankoff

  I am generating postscript graphics and am trying to find a balance between non-aliasing and over-aliasing. If I use the raw ghostscript viewer gs on the Postscript, it looks good. The text appears anti-aliased, but the image remains nice and blocky. Unfortunately, gs has no real user interface and loses all of the nice things that Preview.app has. I could install gv, but the dependency bloat is huge! It requires all of gnome. And even that isn't a great viewer compared to Preview.app or Skim.app. Here is an image viewed with gs: From a user-interaction and Mac-ish perspective, Preview.app (or Skim.app is a much nicer program to use. They have the option to turn on or off aliasing, but neither option looks very good. Which aliasing on, the image is blurry. When it is off, the graphic matches what is seen from gs, but there are two issues. Minor issue: the font is ugly. Uglier than with gs. Major issue: Every PDF is un-aliased, making it hard to read regular PDFs full of text. So, in summary: Is there a way to manually generate the PDF from the PS that overcomes these issues? Is there a way to find a middle ground of alias/unalias with Preview.app? Is there another app that displays with quality like gs, but has a decent UI like Skim.app or Preview.app Is there a way to have Preview.app turn off aliasing for only one file (containing graphics) but leave it enabled in general so that text PDFs are still readable?

  Read the article

• Best SSD tweaks for Windows 7

  - by Nick Berardi

  I have seen many articles about tweaking an SSD, but many of them seem outdated, or too broad (read all Windows XP, Vista, and Windows 7 general tweaks). And I know that Windows 7 has been specifically tweaked for SSD by the Windows team, so I don't want to do something that was written for Windows XP in mind and end up circumventing something the Windows team has specifically designed in to Windows 7. So my question is what are the best SSD tweaks for Windows 7 that you have found to get the performance out of your drive? I hope to make a comprehensive list in the answers below so there won't be so much disinformation in the forums about what to do and what not to do. Here are a few that I see posted up on the forums alot, and some questions to get the discussion started: Disabling Superfetch. Yes or No Disabling Page File or limiting it to a really small size such as 500 MB. Disabling Indexing. Yes or No Disabling Defragmenting. Yes or No What are your thoughts do you have any that have worked for you? When providing an answer please do your best to back it up with a reason and possibly some documentation from MSDN, TechNet, or another credible source.

  Read the article

• No sound out of headphone port

  - by Thanatos

  I cannot get sound out of the headphone port. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller

  Read the article

• Can't start Windows 7 after cloning HDD

  - by Paul

  Brief description: cloned HDD1 - HDD2 HDD1 partition 1 boots HDD1 partition 2 boots HDD2 partition 1 boots HDD2 partition 2 doesn't boot Windows, but is bootable in general Now verbosely: In all the cases computer is the same. I have two Windows 7 installations on HDD1 - both are booting fine. I choose between them using standard Windows 7 boot loader menu. Technically there are 4 partitions: 100 MB Boot loader partition (active), Windows 7 copy 1 (25 GB), Windows 7 copy 2 (150 GB) and Working partition. All are primary. In past few days I tried to clone the whole HDD1 to HDD2 of the same size (but 2,5 inch form factor) as is using Minitool Partition wizard. Everything has been copied, all files are accessible, no faults in file system structure, even boot loader wasn't damaged and I hadn't to repair it. But I can boot only first installation of Windows 7 (it boots without issues). When I choose the second installation, I get immediately a completely black screen without any texts, cursors and other data. HDD isn't accessed after that. This black screen is sensitive to Ctrl-Alt-Delete which causes computer reboot. I did some experimenting: Installed Windows 7 to that partition - it booted fine. Then I renamed "Windows" to "Windows.old" and copied Windows directory from HDD1 as it was, using Far Manager, and got the same troubles - black screen. (Of course I performed renaming and copying from other copy of Windows). So, it seems that problems are inside this installation of Windows, somewhere in its files.

  Read the article

• How to connect via SSH to a linux mint system that is connected via OpenVPN

  - by Hilyin

  Is there a way to make SSH port not get sent through VPN so when my computer is connected to a VPN, it can still be remoted in via SSH from its non-VPN IP? I am using Mint Linux 13. Thank you for your help! This is the instructions I followed to setup the VPN: Open Terminal Type: sudo apt-get install network-manager-openvpn Press Y to continue. Type: sudo restart network-manager Download BTGuard certificate (CA) by typing: sudo wget -O /etc/openvpn/btguard.ca.crt http://btguard.com/btguard.ca.crt Click on the Network Manager icon, expand VPN Connections, and choose Configure VPN A Network Connections window will appear with the VPN tab open. Click Add. 8. A Choose A VPN Connection Type window will open. Select OpenVPN in the drop-down menu and click Create.. . In the Editing VPN connection window, enter the following: Connection name: BTGuard VPN Gateway: vpn.btguard.com Optional: Manually select your server location by using ca.vpn.btguard.com for Canada or eu.vpn.btguard.com for Germany. Type: select Password User name: username Password: password CA Certificate: browse and select this file: /etc/openvpn/btguard.ca.crt Click Advanced... near the bottom of the window. Under the General tab, check the box next to Use a TCP connection Click OK, then click Apply. Setup complete! How To Connect Click on the Network Manager icon in the panel bar. Click on VPN Connections Select BTGuard VPN The Network Manager icon will begin spinning. You may be prompted to enter a password. If so, this is your system account keychain password, NOT your BTGuard password. Once connected, the Network Manager icon will have a lock next to it indicating you are browsing securely with BTGuard.

  Read the article

• Software/hardware to build video streaming server?

  - by Sasha Yanovets

  I am looking for a video streaming server solution, something like online TV server, with ability to make live broadcasts in the internet. What software could you recommend for that? What kind of hardware it should run on, should be there anything special? I am looking for a solution that could be scaled up to at least 1000 simultaneous users online with good resolution of video. I think it is good to have general answer on what direction to choose. But here more details on my specific case: I just looking for a solution almost from scratch. We have some video content that we've produced, but it is not delivered over internet yet. We do not tied to any particular vendor for now. We want to make 24 hours of steaming three 8 hour blocks with change of content every day. We want the ability to make regular live broadcasts. I guess we will need to have several options of streaming quality (low ~56 kb/s mid ~273 kb/s). Some terms just foreign to me (like play-truncation rate), if you could point out what parameters we should avare of, it would be great. Uplink to the internet is to be determined. We plan to start from something and scale up on the way. If you are already have some kind of media streaming server, just describe its configuration here (hardware, OS, software), peak number of concurrent users it serves. I think it could help people approaching this task.

  Read the article

• Memory overcommitment on VmWare ESXi 5.0

  - by Tibor

  I would like to understand better the possibilities of VmWare ESXi memory overcommitment. I've read this paper from VmWare, so I am familiar with general concepts, such as hypervisor swapping, memory balooning and page sharing. It seems that a combination of these techniques allows for quite a large degree of overcommitment. However, I am not sure. I am deploying a virtual test lab comprising of 4 identical sets of virtual servers and workstations and a couple of virtual router instances. Overall, I expect to be running around 20 virtual machines with Windows XP, Windows 7 and Ubuntu for workstation hosts as well as CentOS and Windows 2008 Server instances for servers. The problem is, however, that the host machine only has 12GB of RAM and I don't have an option to stuff in some more. I would like to know what is the best option to configure hosts in order to achieve reasonable performance within the constrains. I have these two options: Allocate as little as possible of RAM to each virtual machine. Allocate an extraordinary amount (such as 4 GB per instance) and let the baloon driver do the rest. Something else? Which would work better? Machines will mostly be idle, so I don't have any major performance expectations, but they should run reasonably smoothly nevertheless.

  Read the article

• Apache: Isn't chmod 755 enough to set up symlink or alias on Apache httpd on Mac OS 10.5?

  - by eed3si9n

  On my Mac OS 10.5 machine, I would like to set up a subfolder of ~/Documents like ~/Documents/foo/html to be http://localhost/foo. The first thing I thought of doing is using Alias as follows: Alias /foo /Users/someone/Documents/foo/html <Directory "/Users/someone/Documents/foo/html"> Options Indexes FollowSymLinks MultiViews Order allow,deny Allow from all </Directory> This got me 403 Forbidden. In the error_log I got: [error] [client ::1] (13)Permission denied: access to /foo denied The subfolder in question has chmod 755 access. I've tried specifying likes like http://localhost/foo/test.php, but that didn't work either. Next, I tried the symlink route. Went into /Library/WebServer/Documents and made a symlink to ~/Documents/foo/html. The document root has Options Indexes FollowSymLinks MultiViews This still got me 403 Forbidden: Symbolic link not allowed or link target not accessible: /Library/WebServer/Documents/foo What else do I need to set this up? Solution: $ chmod 755 ~/Documents In general, the folder to be shared and all of its ancestor folder needs to be viewable by the www service user.

  Read the article

• RAID-capable 3.5" SATA Drives

  - by nroam

  I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

  Read the article

• How can I make a copy of a printer in Win7?

  - by hawbsl

  Has anyone been able to copy an existing printer in Win7? I know that we were able to do this in XP (not as a direct copy/paste, but by installing the printer twice) but in Win7 it doesn't seem to be possible. Googling the answer is hopeless because searching for "copy printer" or "duplicate printer" you get a bunch of posts about "printer copiers" or people complaining about duplicate printers getting created in the background (precisely what I'd like to be able to do) It'd be good to know how to do it in general, but if it depends on the printer type, then in our case we are trying to make a copy of an HP Laserjet. Tried installing from the CD - but the CD is too old for Win7 Tried installing via Add Printer and that seems to install the printer but it's marked with an error. Tried installing via the .exe installer from the HP site and that does result in a successful printer being installed, but it won't let you install the same printer twice (stalls on the "insert USB cable now" step - simply won't enable the greyed out "Next" button). The reason this is required is so that we can print to one to the feeder and to the tray separately.

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

• Losing SQL connections

  - by john pavelka

  sql servr 2005 - Standard; one dedicated sql server (VM); windows server 2003; Small databases; About once a week we lose all sql connections. It seems to fix itself after about 5-10 minutes. System.Web.HttpUnhandledException: Exception of type 'System.Web.HttpUnhandledException' was thrown. --- System.Data.SqlClient.SqlException: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. We don't have a fully qualified DBA; it's kind of a joint effort here. Can somebody give me some general ideas for troubleshooting the network side and the application side? We already ran a few tuning profiles and ran through Database Tuning Advisor to apply indexing recommendations. It would sure be nice if there was a way to take a snapshot of what was running on sql server when these 100% cpu spikes occured, but sometimes we're not around. Is it common to throttle CPU for certain processes? Can this be done with Windows server 2003? For example, if security apps were making cpu spike to 100%, is there a way to limit their cpu usage? Any advice is appreciated. thanks,

  Read the article

• Screen randomly goes blue/black/white

  - by FubsyGamer

  Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

  Read the article

• How to Set Up an SMTP Submission Server on Linux

  - by Kevin Cox

  I was trying to set up a mail server with no luck. I want it to accept mail from authenticated users only and deliver them. I want the users to be able to connect over the internet. Ideally the mail server wouldn't accept any incoming mail. Essentially I want it to accept messages on a receiving port and transfer them to the intended recipient out port 25. If anyone has some good links and guides that would be awesome. I am quite familiar with linux but have never played around with MTA's and am currently running debian 6. More Specific Problem! Sorry, that was general and postfix is complex. I am having trouble enabling the submission port with encryption and authentication. What Works: Sending mail from the local machine. (sendmail [email protected]). Ports are open. (25 and 587) Connecting to 587 appears to work, I get a "need to starttls" warning and starttls appears to work. But when I try to connect with the next command I get the error below. # openssl s_client -connect localhost:587 -starttls smtp CONNECTED(00000003) depth=0 /CN=localhost.localdomain verify error:num=18:self signed certificate verify return:1 depth=0 /CN=localhost.localdomain verify return:1 --- Certificate chain 0 s:/CN=localhost.localdomain i:/CN=localhost.localdomain --- Server certificate -----BEGIN CERTIFICATE----- MIICvDCCAaQCCQCYHnCzLRUoMTANBgkqhkiG9w0BAQUFADAgMR4wHAYDVQQDExVs b2NhbGhvc3QubG9jYWxkb21haW4wHhcNMTIwMjE3MTMxOTA1WhcNMjIwMjE0MTMx OTA1WjAgMR4wHAYDVQQDExVsb2NhbGhvc3QubG9jYWxkb21haW4wggEiMA0GCSqG SIb3DQEBAQUAA4IBDwAwggEKAoIBAQDEFA/S6VhJihP6OGYrhEtL+SchWxPZGbgb VkgNJ6xK2dhR7hZXKcDtNddL3uf1YYWF76efS5oJPPjLb33NbHBb9imuD8PoynXN isz1oQEbzPE/07VC4srbsNIN92lldbRruDfjDrAbC/H+FBSUA2ImHvzc3xhIjdsb AbHasG1XBm8SkYULVedaD7I7YbnloCx0sTQgCM0Vjx29TXxPrpkcl6usjcQfZHqY ozg8X48Xm7F9CDip35Q+WwfZ6AcEkq9rJUOoZWrLWVcKusuYPCtUb6MdsZEH13IQ rA0+x8fUI3S0fW5xWWG0b4c5IxuM+eXz05DvB7mLyd+2+RwDAx2LAgMBAAEwDQYJ KoZIhvcNAQEFBQADggEBAAj1ib4lX28FhYdWv/RsHoGGFqf933SDipffBPM6Wlr0 jUn7wler7ilP65WVlTxDW+8PhdBmOrLUr0DO470AAS5uUOjdsPgGO+7VE/4/BN+/ naXVDzIcwyaiLbODIdG2s363V7gzibIuKUqOJ7oRLkwtxubt4D0CQN/7GNFY8cL2 in6FrYGDMNY+ve1tqPkukqQnes3DCeEo0+2KMGuwaJRQK3Es9WHotyrjrecPY170 dhDiLz4XaHU7xZwArAhMq/fay87liHvXR860tWq30oSb5DHQf4EloCQK4eJZQtFT B3xUDu7eFuCeXxjm4294YIPoWl5pbrP9vzLYAH+8ufE= -----END CERTIFICATE----- subject=/CN=localhost.localdomain issuer=/CN=localhost.localdomain --- No client certificate CA names sent --- SSL handshake has read 1605 bytes and written 354 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: E07926641A5EF22B15EB1D0E03FFF75588AB6464702CF4DC2166FFDAC1CA73E2 Session-ID-ctx: Master-Key: 454E8D5D40380DB3A73336775D6911B3DA289E4A1C9587DDC168EC09C2C3457CB30321E44CAD6AE65A66BAE9F33959A9 Key-Arg : None Start Time: 1349059796 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) --- 250 DSN read:errno=0 If I try to connect from evolution I get the following error: The reported error was "HELO command failed: TCP connection reset by peer".

  Read the article

• Windows Explorer Keeps On Crashing

  - by Josefvz

  Hey Folks. I'm lost... I'm using Windows 7 Ultimate 64bit. My Pc is up to date(windows updates) and I've used Winutilities to scan my registry. My explorer.exe keeps on crashing. Just randomly it seems. I don't even need to be doing anything particular. I do have experience with pc in general as I'm a software developer. I know you will require additional info, but i don't know what, so just leave a comment and I'll update. Additional info I think i should also mention that explorer is the only app that crashes on my pc. The crash report i got now: Description: A problem caused this program to stop interacting with Windows. Problem signature: Problem Event Name: AppHangB1 Application Name: explorer.exe Application Version: 6.1.7600.16450 Application Timestamp: 4aebab8d Hang Signature: 0a1b Hang Type: 16897 OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 7177 Additional Hang Signature 1: 0a1bdae38ae7300761c516c4416d992c Additional Hang Signature 2: 1c51 Additional Hang Signature 3: 1c518a49cc7d37652d26c521e96f66c2 Additional Hang Signature 4: 521e Additional Hang Signature 5: 521e607ec26a72aab4ae5a7126916ef3 Additional Hang Signature 6: e5e3 Additional Hang Signature 7: e5e3ca31dad607fa7b858ff5ea5c0fa9

  Read the article

< Previous Page | 374 375 376 377 378 379 380 381 382 383 384 385  | Next Page >