Search Results

Search found 11313 results on 453 pages for 'ip aliasing'.

Page 379/453 | < Previous Page | 375 376 377 378 379 380 381 382 383 384 385 386  | Next Page >

• Sonicwall routing between multiple subnets on multiple interfaces

  - by Rain

  As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

  Read the article

• Hyper V Server 2012 Remote Management Using Workgroup

  - by Chris Kolenko

  I'm trying to remotely manage Hyper V server 2012 from a windows 8 pc, both client and server are on a workgroup. I've spent about 3-4 hours trying to get this working with no luck so far trying the following: Creating a new administrator on the server with the same details as the client ie. username / password. Add an entry into my hosts file to point to the remote ip by server name. Tried using HVRemote. Disabled both firewalls. The error that I'm getting is RPC Service Unavailable. How can I accomplish what I'm trying to do? Update Some of the operations on the Hyper-V Manager work. IE. Virtual Switch Works. I can open the New VM Wizard. I run into an error when creating a new Virtual Hard Disk tho. I've tried creating a VM without a hard disk, which works. Using the new hard disk wizard does not work either. I still can not see any Virtual Machines. RPC server unavailable. Unable to establish communication between 'ServerName' and 'ClientName'

  Read the article

• Converting Lighttpd config to NginX with php-fpm

  - by Le Dude

  Having so much issue with NginX configuration since I'm new with NginX. Been using Lighttpd for quite sometime. Here are the base info. New Machine - CentOS 6.3 64 Bit - NginX 1.2.4-1.e16.ngx - Php-FPM 5.3.18-1.e16.remi Old Machine - CentOS 6.2 64Bit - Lighttpd 1.4.25-3.e16 Original Lighttpd config file: ####################################################################### ## ## /etc/lighttpd/lighttpd.conf ## ## check /etc/lighttpd/conf.d/*.conf for the configuration of modules. ## ####################################################################### ####################################################################### ## ## Some Variable definition which will make chrooting easier. ## ## if you add a variable here. Add the corresponding variable in the ## chroot example aswell. ## var.log_root = "/var/log/lighttpd" var.server_root = "/var/www" var.state_dir = "/var/run" var.home_dir = "/var/lib/lighttpd" var.conf_dir = "/etc/lighttpd" ## ## run the server chrooted. ## ## This requires root permissions during startup. ## ## If you run Chrooted set the the variables to directories relative to ## the chroot dir. ## ## example chroot configuration: ## #var.log_root = "/logs" #var.server_root = "/" #var.state_dir = "/run" #var.home_dir = "/lib/lighttpd" #var.vhosts_dir = "/vhosts" #var.conf_dir = "/etc" # #server.chroot = "/srv/www" ## ## Some additional variables to make the configuration easier ## ## ## Base directory for all virtual hosts ## ## used in: ## conf.d/evhost.conf ## conf.d/simple_vhost.conf ## vhosts.d/vhosts.template ## var.vhosts_dir = server_root + "/vhosts" ## ## Cache for mod_compress ## ## used in: ## conf.d/compress.conf ## var.cache_dir = "/var/cache/lighttpd" ## ## Base directory for sockets. ## ## used in: ## conf.d/fastcgi.conf ## conf.d/scgi.conf ## var.socket_dir = home_dir + "/sockets" ## ####################################################################### ####################################################################### ## ## Load the modules. include "modules.conf" ## ####################################################################### ####################################################################### ## ## Basic Configuration ## --------------------- ## server.port = 80 ## ## Use IPv6? ## #server.use-ipv6 = "enable" ## ## bind to a specific IP ## #server.bind = "localhost" ## ## Run as a different username/groupname. ## This requires root permissions during startup. ## server.username = "lighttpd" server.groupname = "lighttpd" ## ## enable core files. ## #server.core-files = "disable" ## ## Document root ## server.document-root = server_root + "/lighttpd" ## ## The value for the "Server:" response field. ## ## It would be nice to keep it at "lighttpd". ## #server.tag = "lighttpd" ## ## store a pid file ## server.pid-file = state_dir + "/lighttpd.pid" ## ####################################################################### ####################################################################### ## ## Logging Options ## ------------------ ## ## all logging options can be overwritten per vhost. ## ## Path to the error log file ## server.errorlog = log_root + "/error.log" ## ## If you want to log to syslog you have to unset the ## server.errorlog setting and uncomment the next line. ## #server.errorlog-use-syslog = "enable" ## ## Access log config ## include "conf.d/access_log.conf" ## ## The debug options are moved into their own file. ## see conf.d/debug.conf for various options for request debugging. ## include "conf.d/debug.conf" ## ####################################################################### ####################################################################### ## ## Tuning/Performance ## -------------------- ## ## corresponding documentation: ## http://www.lighttpd.net/documentation/performance.html ## ## set the event-handler (read the performance section in the manual) ## ## possible options on linux are: ## ## select ## poll ## linux-sysepoll ## ## linux-sysepoll is recommended on kernel 2.6. ## server.event-handler = "linux-sysepoll" ## ## The basic network interface for all platforms at the syscalls read() ## and write(). Every modern OS provides its own syscall to help network ## servers transfer files as fast as possible ## ## linux-sendfile - is recommended for small files. ## writev - is recommended for sending many large files ## server.network-backend = "linux-sendfile" ## ## As lighttpd is a single-threaded server, its main resource limit is ## the number of file descriptors, which is set to 1024 by default (on ## most systems). ## ## If you are running a high-traffic site you might want to increase this ## limit by setting server.max-fds. ## ## Changing this setting requires root permissions on startup. see ## server.username/server.groupname. ## ## By default lighttpd would not change the operation system default. ## But setting it to 2048 is a better default for busy servers. ## ## With SELinux enabled, this is denied by default and needs to be allowed ## by running the following once : setsebool -P httpd_setrlimit on server.max-fds = 2048 ## ## Stat() call caching. ## ## lighttpd can utilize FAM/Gamin to cache stat call. ## ## possible values are: ## disable, simple or fam. ## server.stat-cache-engine = "simple" ## ## Fine tuning for the request handling ## ## max-connections == max-fds/2 (maybe /3) ## means the other file handles are used for fastcgi/files ## server.max-connections = 1024 ## ## How many seconds to keep a keep-alive connection open, ## until we consider it idle. ## ## Default: 5 ## #server.max-keep-alive-idle = 5 ## ## How many keep-alive requests until closing the connection. ## ## Default: 16 ## #server.max-keep-alive-requests = 18 ## ## Maximum size of a request in kilobytes. ## By default it is unlimited (0). ## ## Uploads to your server cant be larger than this value. ## #server.max-request-size = 0 ## ## Time to read from a socket before we consider it idle. ## ## Default: 60 ## #server.max-read-idle = 60 ## ## Time to write to a socket before we consider it idle. ## ## Default: 360 ## #server.max-write-idle = 360 ## ## Traffic Shaping ## ----------------- ## ## see /usr/share/doc/lighttpd/traffic-shaping.txt ## ## Values are in kilobyte per second. ## ## Keep in mind that a limit below 32kB/s might actually limit the ## traffic to 32kB/s. This is caused by the size of the TCP send ## buffer. ## ## per server: ## #server.kbytes-per-second = 128 ## ## per connection: ## #connection.kbytes-per-second = 32 ## ####################################################################### ####################################################################### ## ## Filename/File handling ## ------------------------ ## ## files to check for if .../ is requested ## index-file.names = ( "index.php", "index.rb", "index.html", ## "index.htm", "default.htm" ) ## index-file.names += ( "index.xhtml", "index.html", "index.htm", "default.htm", "index.php" ) ## ## deny access the file-extensions ## ## ~ is for backupfiles from vi, emacs, joe, ... ## .inc is often used for code includes which should in general not be part ## of the document-root url.access-deny = ( "~", ".inc" ) ## ## disable range requests for pdf files ## workaround for a bug in the Acrobat Reader plugin. ## $HTTP["url"] =~ "\.pdf$" { server.range-requests = "disable" } ## ## url handling modules (rewrite, redirect) ## #url.rewrite = ( "^/$" => "/server-status" ) #url.redirect = ( "^/wishlist/(.+)" => "http://www.example.com/$1" ) ## ## both rewrite/redirect support back reference to regex conditional using %n ## #$HTTP["host"] =~ "^www\.(.*)" { # url.redirect = ( "^/(.*)" => "http://%1/$1" ) #} ## ## which extensions should not be handle via static-file transfer ## ## .php, .pl, .fcgi are most often handled by mod_fastcgi or mod_cgi ## static-file.exclude-extensions = ( ".php", ".pl", ".fcgi", ".scgi" ) ## ## error-handler for status 404 ## #server.error-handler-404 = "/error-handler.html" #server.error-handler-404 = "/error-handler.php" ## ## Format: <errorfile-prefix><status-code>.html ## -> ..../status-404.html for 'File not found' ## #server.errorfile-prefix = "/srv/www/htdocs/errors/status-" ## ## mimetype mapping ## include "conf.d/mime.conf" ## ## directory listing configuration ## include "conf.d/dirlisting.conf" ## ## Should lighttpd follow symlinks? ## server.follow-symlink = "enable" ## ## force all filenames to be lowercase? ## #server.force-lowercase-filenames = "disable" ## ## defaults to /var/tmp as we assume it is a local harddisk ## server.upload-dirs = ( "/var/tmp" ) ## ####################################################################### ####################################################################### ## ## SSL Support ## ------------- ## ## To enable SSL for the whole server you have to provide a valid ## certificate and have to enable the SSL engine.:: ## ## ssl.engine = "enable" ## ssl.pemfile = "/path/to/server.pem" ## ## The HTTPS protocol does not allow you to use name-based virtual ## hosting with SSL. If you want to run multiple SSL servers with ## one lighttpd instance you must use IP-based virtual hosting: :: ## ## $SERVER["socket"] == "10.0.0.1:443" { ## ssl.engine = "enable" ## ssl.pemfile = "/etc/ssl/private/www.example.com.pem" ## server.name = "www.example.com" ## ## server.document-root = "/srv/www/vhosts/example.com/www/" ## } ## ## If you have a .crt and a .key file, cat them together into a ## single PEM file: ## $ cat /etc/ssl/private/lighttpd.key /etc/ssl/certs/lighttpd.crt \ ## > /etc/ssl/private/lighttpd.pem ## #ssl.pemfile = "/etc/ssl/private/lighttpd.pem" ## ## optionally pass the CA certificate here. ## ## #ssl.ca-file = "" ## ####################################################################### ####################################################################### ## ## custom includes like vhosts. ## #include "conf.d/config.conf" #include_shell "cat /etc/lighttpd/vhosts.d/*.conf" ## ####################################################################### ####################################################################### ### Custom Added by me #url.rewrite-once = (".*\.(js|ico|gif|jpg|png|css|jar|class)$" => "$0", "" => "/index.php") url.rewrite-once = ( ".*\?(.*)$" => "/index.php?$1", "^/js/.*$" => "$0", "^.*\.(js|ico|gif|jpg|png|css|swf |jar|class)$" => "$0", "" => "/index.php" ) # expire.url = ( "" => "access 1 days" ) include "myvhost-vhosts.conf" ####################################################################### Here is my Vhost file for lighttpd $HTTP["host"] =~ "192.168.8.35$" { server.document-root = "/var/www/lighttpd/qc41022012/public" server.errorlog = "/var/log/lighttpd/error.log" accesslog.filename = "/var/log/lighttpd/access.log" server.error-handler-404 = "/e404.php" } and here is my nginx.conf file user nginx; worker_processes 5; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/testsite/logs/access.log main; sendfile on; #tcp_nopush on; keepalive_timeout 65; #gzip on; # include /etc/nginx/conf.d/*.conf; ## I added this ## include /etc/nginx/sites-available/*; } Here is my NginX Vhost file server { server_name 192.168.8.91; access_log /var/log/nginx/myapps/logs/access.log; error_log /var/log/nginx/myapps/logs/error.log; root /var/www/html/myapps/public; location / { index index.html index.htm index.php; } location = /favicon.ico { return 204; access_log off; log_not_found off; } # location ~ \.php$ { # try_files $uri /index.php; # include /etc/nginx/fastcgi_params; # fastcgi_pass 127.0.0.1:9000; # fastcgi_index index.php; # fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; # fastcgi_param SCRIPT_NAME $fastcgi_script_name; location ~ \.php.*$ { rewrite ^(.*.php)/ $1 last; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; # fastcgi_intercept_errors on; # fastcgi_param SCRIPT_FILENAME $document_root/index.php; # fastcgi_param PATH_INFO $uri; # fastcgi_pass 127.0.0.1:9000; # include fastcgi_params; } } We have a custom apps that we created that works great with lighttpd. I went through some headache also when we were trying to figure out how to make it work with lighttpd. this is the line that helps make it work in lighttpd. url.rewrite-once = ( ".*\?(.*)$" => "/index.php?$1", "^/js/.*$" => "$0", "^.*\.(js|ico|gif|jpg|png|css|swf |jar|class)$" => "$0", "" => "/index.php" ) but I couldn't figure out how to make it works in NginX. The webserver run just fine when we use the phpinfo.php test file. However as soon as I point it to my apps, nothing comes up. Check the error.log file and there's no error. Very mind boggling. I spent over 1 week trying to figure it out with no luck.. Please help?

  Read the article

• IIS6.0 asking for credentials after MS Updates

  - by Adam M.

  We have an IIS6.0 Server running on a Windows 2003 Server. Last weekend it went though maintenance, and updated a quite a few Windows updates, it is now brought up to current updates (as of March 29th). Previous to these updates we could connect to the Web page via the hostname or via a alias (there is a DNS and a WINS alias (the alias is the same name in both) that are both pointing to the system). Now since the updates it asks for credentials to access the page, when trying to access the page via IP, or by name. If you use the alias it will go right into the page. I had added a new alias in DNS and tried to access it via this name with the same effect. So it appears that the WINS alias allows the page to show up properly. I have seen this KB but http://support.microsoft.com/kb/871179 though not sure if it really is relevant to this issue. As it does refer to the 3 strikes rules to display the 401.1 error. The IIS Application pool is running under a domain account. Teh default page is allowing Anonymous login under a local account. Any thoughts? Thanks Adam

  Read the article

• Configure APE-Server on Ubuntu10.10 webserver

  - by sadmicrowave

  I'm having problems configuring my ape-server. First, I reside behind a corporate firewall where our own DNS servers are maintained. I requested a domain name for my server and was provided uslonsweb003.us.mycompany.com from my IT group. Therefore, my website works and can be accessed via (intranet only) at http://uslonsweb003.us.mycompany.com/test.php. I followed the instructions at ape-project.org and run the Check Tool at the end only to find I get an error stating: Running test : Contacting APE Server (adding frequency) Can't contact APE Server. Please check the folowing url is pointing to your APE server : http://0.uslonsweb003.us.mycompany.com:6969 my /etc/apache2/apache2.conf module looks as follows: <VirtualHost *:80> Servername uslonsweb003.us.mycompany.com ServerAlias ape.uslonsweb003.us.mycompany.com ServerAlias *.ape.uslonsweb003.us.mycompany.com DocumentRoot "/var/www/" </VirtualHost> my /var/www/ape-jsf/Demos/config.js config section looks as follows: APE.Config.baseUrl = 'http://uslonsweb003.us.mycompany.com/ape-jsf'; APE.Config.domain = 'uslonsweb003.us.mycompany.com'; APE.Config.server = 'uslonsweb003.us.mycompany.com:6969'; The instructions at ape-project.org tell me that the APE.Config.server should be `ape.mydomain.com:6969'; but that does not work (I'm assuming because my corporate DNS does not understand the 'ape' before the domain name since 'ape' was not registered with the IT DNS). So therefore, I changed it to what you see above. Please help!! Thanks in advance UPDATE 1 per the installation instructions located on this page http://www.ape-project.org/wiki/index.php/Advanced_APE_configuration under 'Configure your Server/Computer' (I'm running it on a server obviously) It says I need to add some lines to my DNS config file. It sounds like (since I'm within a corporate network) I would ask my IT group to add the following lines to the DNS configuration file on their end: ape IN A x.x.x.x ; IP address of my APE server *.ape IN CNAME ape I just want to make sure this is all I have to have them add (or if this is even correct) before I ask them.

  Read the article

• SQL Server 2008: Can't connect to remote server via management studio but can telnet in fine

  - by WarpKid

  Hi, I am in the process of trying to configure SQL Server 2008 to accept remote connections. I have been through all the documentation I can find and yet when I attempt to connect through management studio I get an error stating that the server could not be found. Interestingly I can connect through telnet to the remote server via the port that sql server is listening on. In the SQL Server logs I can see the connection attempt. So SQL Server is up and running and listening on the correct port - no firewall blocking it. It would appear that by default SQL Server is listening on port 50314 by default but management studio attempts to connect on port 1433.Weird. Server Management Studio = no dice. Anyone got any ideas? Server is set to allow remote connections - TCP IP is enabled, firewall is off. Thanks UPDATE FOR TO CLEAR THINGS UP A BIT We are seeing the connection attempt when we telnet in on port 50314 in the sql server logs. When we login through management studio we see it attempting connection on port 1433. There is no sign of this connection attempt in the logs.

  Read the article

• Getting 400 Bad Request when requesting by server name on nginx/uwsgi

  - by Marc Hughes

  I'm trying to run 2 different sites on nginx via different ports (they each have a load balancer that points to the appropriate port). The first site work perfectly. The second site... If I access http://localhost:81/ it works correctly If I access http://127.0.01:81/ it works correctly If I access the hostname http://THEHOSTNAME:81/ it fails with a 400 error If I access the public IP http://x.x.x.x:81/ it fails with a 400 error I've set the error_log to info, but the only lines I get in the log when this happens is: ==> /var/log/nginx/access.log <== 10.183.38.141 - - [24/Aug/2014:21:03:28 +0000] "GET / HTTP/1.1" 400 37 "-" "curl/7.36.0" "-" ==> /var/log/nginx/error.log <== 2014/08/24 21:03:28 [info] 7029#0: *5 client 10.183.38.141 closed keepalive connection In my uwsgi log, I only see this: [pid: 6870|app: 0|req: 87/92] 10.28.23.224 () {32 vars in 380 bytes} [Sun Aug 24 21:05:21 2014] GET / => generated 26 bytes in 1 msecs (HTTP/1.1 400) 2 headers in 82 bytes (1 switches on core 2) What should be my next step in debugging this?

  Read the article

• How to run some commands after booting from ArchLinux disk? Or how to change some settings in .iso before booting?

  - by Alexander Ovchinnikov

  How to install Arch Linux with traditional installer with only ssh-access to server? There is nice guide: https://wiki.archlinux.org/index.php/Install_from_SSH I try test this on my home vps: Start VPS with any linux bootable cd and login to remote server (vps) wget http://mirrors.kernel.org/archlinux/iso/latest/archlinux-2010.05-netinstall-x86_64.iso dd if=archlinux-2010.05-netinstall-x86_64.iso of=/dev/sda reboot ... I see, it works but without ssh connection... I need make script, which will send this commands after reboot: aif -p partial-configure-network (and write some information about my server ip etc.) /etc/rc.d/sshd start (need to start sshd) echo "sshd: ALL" /etc/hosts.allow (to allow me login to server, by default deny all) passwd (by default its empty, can't login via ssh with empty password) Can I edit .iso or may be /dev/sda? May be I need write script, which will start after system boot and do this things or may be I can set this settings by default and system will start with correct settings (i think its possible at least in 2. and 3.). Thank you!

  Read the article

• Why the system information message when accessing an Ubuntu server doesn't match free -m?

  - by Andres

  Each time I SSH into my AWS Ubuntu servers I see a system information message, showing load, memory usage and packages available to install, like this: Welcome to Ubuntu 12.04.3 LTS (GNU/Linux 3.2.0-51-virtual x86_64) * Documentation: https://help.ubuntu.com/ System information as of Sun Nov 10 18:06:43 EST 2013 System load: 0.08 Processes: 127 Usage of /: 4.9% of 98.43GB Users logged in: 1 Memory usage: 69% IP address for eth0: 10.236.136.233 Swap usage: 100% Graph this data and manage this system at https://landscape.canonical.com/ 13 packages can be updated. 0 updates are security updates. Get cloud support with Ubuntu Advantage Cloud Guest http://www.ubuntu.com/business/services/cloud Use Juju to deploy your cloud instances and workloads. https://juju.ubuntu.com/#cloud-precise *** /dev/xvda1 will be checked for errors at next reboot *** *** System restart required *** My question is about the memory percentage shown. In this case, it's showing a 69% of memory usage, but since the swap usage was 100% I checked it by myself. So when I run free -m I get this: total used free shared buffers cached Mem: 1652 1635 17 0 4 29 -/+ buffers/cache: 1601 51 Swap: 895 895 0 And that's of course closer to 100% than to 69%

  Read the article

• 16-bit MS-DOS Subsystem: csrss.exe

  - by Wesley

  Hi all, I just booted up my Samsung N120 netbook (with Windows XP Home SP3) and a dialog box came up with a command prompt window behind it. The dialog box is titled 16 bit MS-DOS Subsystem and the message is as follows: C:\DOCUME~1\SAMSUNG\csrss.exe The NTVDM CPU has encountered an illegal instruction. CS:0544 IP:0117 OP:63 00 64 00 34 Choose 'Close' to terminate the application. This only started on my most recent boot-up. One thing to note is that when I downloaded the Dropbox installer and opened it up, Panda Cloud Antivirus detected a suspicious file, which was csrss.exe and "neutralized it." However, an actual virus or trojan was not detected immediately before the file was detected and neutralized. Just under two weeks ago, a trojan and two viruses were detected for some odd reason. (I only went to website I knew and I do not torrent or browse adult sites.) Anyhow, the two viruses came up in temporary files and the trojan was "neutralized." Anyways, the main question is: How can I repair the csrss.exe file such that Windows XP starts up properly? A screenshot could be posted upon request. Thanks in advance!

  Read the article

• Can a wifi AP act as a client, and a server at the same time?

  - by nbolton

  I feel this is SF worthy (as opposed to SU) as I go into a bit of detail on gateways/routing. Here's my ideal setup (if possible) -- there is a wifi network (lets call it bob's) with which I want access to, but I have a few other computers on my network which I want to keep behind a firewall. So I was thinking of buying a wireless access point so that I could set it up to connect to bob's network from the AP, and then from my server, connect to the AP via ethernet. So that's the first bit. Second part is that I want to have my own private wifi network off the back of this; can I then tell the AP to serve a new network called foobar. When I say private network, I mean that my server is actually a Debian linux install with routing configured (and I also do some QoS stuff on, etc). So ideally, I'd like all the clients on the private network to be behind the server in terms of routing. However, if the private clients connect to the server via wifi, then aren't they exposed to the "public" network? That is, if someone is savvy enough to scan for my IP range. Also, to do routing I'd need to connect two ethernet cables between the server and the AP (because you can't do routing/QoS on virtual devices) -- which isn't a problem really; but I'm not sure whether the AP will allow me to separate the public and private LANs. Or, as well as the AP, am I better getting a wifi-to-ethernet adapter for the server? I could use a wifi usb, but this can be tricky to set up on headless linux; plus the signal strength is a bit lousy. If this question is a bit vague/spurious in places, please comment and I will explain in more detail.

  Read the article

• what can be causes of http server crash?

  - by mithunmo

  Hello , I am using WAMP server on Windows XP. Apache 2.2.11 MySQL 5.1.36 (INNODB engine) PHP 5.3.0 I observe that my WAMP server crashes in the following scenarios IF I use a Low end PC ( low processor speed and low RAM) After making some changes to httpd.conf file .For eg changing the Allow from IP address . But here it crashes only once and then it starts to work fine. Random crashes CRASH LOG szAppName : httpd.exe szAppVer : 2.2.11.0 szModName : php5ts.dll szModVer : 5.3.0.0 offset : 0000c309 C:\DOCUME~1\blrcom\LOCALS~1\Temp\WERc677.dir00\httpd.exe.mdmp C:\DOCUME~1\blrcom\LOCALS~1\Temp\WERc677.dir00\appcompat.txt My questions Does high CPU utilization/LOW RAM can also cause the HTTP server to crash ? excessive file reading as in every 10 seconds ? unlimited script execution time . I have set the maximum execution time in php script to 0 as my script has to execute for sometimes 2-3 days. Is there any way to avoid this ? Access to Database ? Should we use lock before reading and writing Can these be the reasons for random wamp server crashes ? OR is is some other programming error ? Please guide me . Regards, Mithun

  Read the article

• Attempting to update Amazon Route53 using a script, but domain is not being updated

  - by ks78

  I have several Amazon EC2 instances, running Ubuntu 10.04, with which I'd like to use Amazon's Route53. I setup a script as described in Shlomo Swidler's article, but I'm still missing something. When the script runs, it doesn't return any output, which I initially assumed meant it ran correctly. However, when I check the DNS records using MyR53DNS, there are no entries for my instances. Here's my script: #!/bin/tcsh -f set root=`dirname $0` setenv EC2_HOME /usr/lib/ec2-api-tools setenv EC2_CERT /etc/cron.route53/ec2_x509_cert.pem setenv EC2_PRIVATE_KEY /etc/cron.route53/ec2_x509_private.pem setenv AWS_ACCESS_KEY_ID myaccesskeyid setenv AWS_SECRET_ACCESS_KEY mysecretaccesskey /user/bin/ec2-describe-instances | \ perl -ne '/^INSTANCE\s+(i-\S+).*?(\S+\.amazonaws\.com)/ \ and do { $dns = $2; print "$1 $dns\n" }; /^TAG.+\sShortName\s+(\S+)/ \ and print "$1 $dns\n"' | \ perl -ane 'print "$F[0] CNAME $F[1] --replace\n"' | \ xargs -n 4 $/etc/cron.route53/cli53/cli53.py \ rrcreate -x 60 mydomain.com Does anyone see a problem with this script? If its not the script, what else could be preventing my Route53 domain from being updated? I am using the Security Groups to IP-restrict the instances. I've tried opening port 53, but that didn't seem to have an effect. Is there another port that Route53 uses? I'd appreciate any help or guidance the ServerFault community can offer. Let me know if you need any further info.

  Read the article

• Server 2003, XP Clients, DNS issues

  - by ron

  Hello, Im having DNS issues on my network. My DC is my DNS server 10.76.4.11 and recently I configured a forwarder to 10.4.36.10. My workstations are not working because they cannot resolve the domain controller name because of DNS. an ipconfig /all reveals that they know the IP of the DNS server is 10.76.4.11, but if I nslookup 10.76.4.11 it forwards the request to 10.4.36.10 and goes nowhere. I have since removed the forwarder, but still any nslookup requests on workstations are going to 10.4.36.10. If I nslookup 10.76.4.11 on the server it can resolve its name, but for some reason when it receives the same request from workstations it doesnt know what to do. All the A, CNAME records etc are correct. DHCP's DNS is set correctly, GPOs are correct (even though they cant refresh cos of this problem!), the servers network adapter has its DNS set to 10.76.4.11. Just don't know. Very confused.

  Read the article

• Why does my Belkin wireless router has eMule port open?

  - by Jeremy Powell

  I have a Belkin F6D4230-4 v1 router. When I port scan it with nmap I get the following: $ sudo nmap -sS -A -T5 192.168.2.1 -p- Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-17 11:40 CDT Interesting ports on 192.168.2.1: Not shown: 65532 closed ports PORT STATE SERVICE VERSION 80/tcp open http Belkin 2307 wifi router http config (IP_SHARER httpd 1.0) |_ html-title: '+i1+' 4661/tcp filtered unknown 4662/tcp filtered edonkey MAC Address: 00:22:75:5D:52:D8 (Belkin International) Device type: WAP|broadband router|firewall|printer|specialized|webcam Running (JUST GUESSING) : Linksys embedded (95%), TRENDnet embedded (95%), Netgear embedded (92%), Canon embedded (89%), On Time RTOS (89%), Symantec embedded (89%), D-Link embedded (86%), Polycom embedded (85%) Aggressive OS guesses: Linksys WRT54GC or TRENDnet TEW-431BRP wireless broadband router (95%), TRENDnet TW100-BRF114 broadband router (95%), Netgear FR114P ProSafe VPN firewall (92%), Canon PIXMA MX850 printer (89%), On Time RTOS (89%), Symantec Firewall/VPN 100 (89%), D-Link DI-714P+ wireless broadband router (86%), Polycom ViewStation video conferencing system (85%) No exact OS matches for host (test conditions non-ideal). Network Distance: 1 hop Service Info: Device: WAP OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 21.57 seconds Why are the 4461 and 4462 ports open? This is a basic, out-of-the-box installation.

  Read the article

• Vmware Player 3.0 - cannot ping 32 bits guest from 64 bits (guest or host)

  - by npmj

  I'm stuck with what seems a bug in VmWare Player (build 203739). I'm using W7 Ultimate 64bits as host and have a CentOS 5.4 (64 bits) as a guest and a Windows XP Professional SP3 (32 bits) as another guest. From the 64 bits machines (the host and the linux guest) I cannot ping the windows XP. Off course, I already turned off the windows firewall in the guest and also in the host. The network is pretty basic, I'm using Vmnet8 (NAT), with DHCP and port forwarding (to the windows XP's IP). Everything is working ok, I have internet access from host and from both guests. Port forwarding to the XP guest is working ok too. The only problem is that I cannot access the XP guest through the Vmnet8. I monitored the traffic using wireshark (in the host and in the windows guest). If I try to ping the XP guest from the host, what I see is the ARP request leaving the host, being answered by the guest and, after that, there is no echo request leaving the host. The same occurs if I try to ping the XP from the CentOs guest. From the windows XP guest I can ping both the host and the CentOs guest. From the XP guest I can access the host shares. Obviously, from the host I cannot see the XP shares (as I cannot even ping the guest). I want to maintain this setup (using NAT to share the host's internet connection). Any suggestions?

  Read the article

• What's the risk of running a Domain Controller so that it is accessible from the internet?

  - by Adrian Grigore

  I have three remote dedicated web servers at different webhosts. Adding them to a common domain would make a lot of administration tasks much easier. Since two of the servers are running Windows 2008 R2 Standard, I thought about promoting them to Domain Controllers in order to set up the windows domain. There's another thread at Serverfault that recommends this. At the same time I've read a lot of times on different websites that this is not a good idea because an domain controller should always be behind a firewall LAN. But I can't set up something like this because I don't have a LAN with a static IP accessible from the internet. In fact I don't even have a windows server in my LAN. What I have not found out is why exposing a DC to the Internet would be bad idea. The only risk I can see is that if someone penetrates one of my webservers, it should be much easier to penetrate the others as well. But as far as I can see that's the worst case scenario since I am only going my web servers to that domain, not any computers from my local network. Is this the only downside or does it also make it easier to penetrate one of my web servers in the first place? Thanks, Adrian

  Read the article

• fail2ban Error Gentoo

  - by Mark Davidson

  Hi All I've recently setup a new VPS running Gentoo (My first time using the distro so please forgive me is this is a really easy one) and as I've done with other servers installed fail2ban. Setting it up to block the host via iptables, on too many unsuccessful logins with ssh. However I'm getting a strange error that I can't quite solve. When I start fail2ban I get these lines in the error log 2009-11-13 18:02:01,290 fail2ban.jail : INFO Jail 'ssh-iptables' started 2009-11-13 18:02:01,480 fail2ban.actions.action: ERROR iptables -N fail2ban-SSH iptables -A fail2ban-SSH -j RETURN iptables -I INPUT -p tcp --dport ssh -j fail2ban-SSH returned 100 If I try and force a ban these errors show up in the log and the host is not banned 2009-11-13 11:23:26,905 fail2ban.actions: WARNING [ssh-iptables] Ban XXX.XXX.XXX.XXX 2009-11-13 11:23:26,929 fail2ban.actions.action: ERROR iptables -n -L INPUT | grep -q fail2ban-SSH returned 100 2009-11-13 11:23:26,930 fail2ban.actions.action: ERROR Invariant check failed. Trying to restore a sane environment 2009-11-13 11:23:27,007 fail2ban.actions.action: ERROR iptables -N fail2ban-SSH iptables -A fail2ban-SSH -j RETURN iptables -I INPUT -p tcp --dport ssh -j fail2ban-SSH returned 100 2009-11-13 11:23:27,016 fail2ban.actions.action: ERROR iptables -n -L INPUT | grep -q fail2ban-SSH returned 100 2009-11-13 11:23:27,016 fail2ban.actions.action: CRITICAL Unable to restore environment My versions are as follows Linux masked 2.6.18-xen-r12 #2 SMP Wed Mar 4 11:45:03 GMT 2009 x86_64 Intel(R) Xeon(R) CPU E5504 @ 2.00GHz GenuineIntel GNU/Linux net-analyzer/fail2ban-0.8.4 net-firewall/iptables-1.4.3.2 If anyone could shead some light on these errors that would be great, I did wonder if it was a problem with iptables or some kernel modules but I can block an IP if I do. iptables -I INPUT -s 25.55.55.55 -j DROP so makes me think its something a bit more unusual. Thanks a lot in advance

  Read the article

• Windows 7 - Wireless Signal Good - Internet Often Says Limited or No Activity

  - by Anthony Trilussa Pizzo

  Hi - I have a New Dell Studio XPS latop that I hooked up in early January of 2010. The Dell Studio XPS laptop is connected to my wireless router (Belkin Wireless N). The router was purchased in Februaru of 2010 because I thought my router was bad (A D-Link router). Comcast is my ISP. Everyday, at random times, the internet will have a good signal (according to the little Win 7 icon on the taskbar) but I will receive a message saying limited or no internet access and I cannot access the internet. I have the internet setup to automatically get an IP and I did the IPCONFIG release / renew but with no success. I even had a WiFi enabled Blackberry right next to my computer and whenever the computer loses an WiFi connection, so does the Blackberry. The router isnt't bad, because the old router did the same thing - giving me limited or no internet access while working sometimes. I also tried using two other laptops in same physical position as my Dell Studio XPS laptop and they have the same problem. I am going crazy trying to figure this out as I have called the Router Company (Belkin), my ISP (Comcast), and my computer maker (Dell). Can anyone offer some suggestions and I can try them as we work through this and maybe one of the suggestion will be right one. Thanks in advance for even reading my problem. I searched for a problem similar to mine on the internet, but I have not been able to keep a steady internet connection. (Side note - I used to have an IBM thinkpad laptop and D - Link router and for years that wireless connection worked FLAWLESSLY, with the same physical set up - the laptop in my bedroom, and the router in the basement.)

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0?

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). xxxx:xxxx:xxxx/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else?

  Read the article

• Apache2: not defined domains directing to the same virtual host

  - by rafaame

  I have Apache2 configured in a debian box with virtual hosts. I have several domains pointing to the box's IP address. The domains whose virtual hosts are configured works perfectly. But if I type in the browser a domain that is pointing to the box but whose the virtual host is not configured, I get to a random virtual host of another domain in the box. Not a random, but one of the virtual hosts (always the same) but I dunno why it is it. The correct would be that the domains that are not configured as virtual hosts return a hostname error or something, right? Does someone know how to fix the problem? One of my virtual hosts config file: <VirtualHost *:80> ServerAdmin [email protected] ServerName dl.domain.com DocumentRoot /var/www/dl.domain.com/public_html/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/dl.domain.com/public_html/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My apache2.conf http://www.speedyshare.com/files/29107024/apache2.conf Thanks for the help

  Read the article

• strange Postfix logwatch log summary on my ubuntu vps

  - by DannyRe

  Hi I would be very thankful if someone could help me on explaining this logwatch summary of my postfix installation on my ubuntu 10.04 vps. I dont really know if this might be a normal log file because of the many authentication failed entries and foreign IP addresses. Any advise for a novice? Thx! ****** Summary ************************************************************************************* 113 SASL authentication failed 195 Miscellaneous warnings 8.419K Bytes accepted 8,621 8.419K Bytes delivered 8,621 ======== ================================================== 3 Accepted 60.00% 2 Rejected 40.00% -------- -------------------------------------------------- 5 Total 100.00% ======== ================================================== 2 5xx Reject relay denied 100.00% -------- -------------------------------------------------- 2 Total 5xx Rejects 100.00% ======== ================================================== 116 Connections 1 Connections lost (inbound) 116 Disconnections 3 Removed from queue 3 Delivered 1 Hostname verification errors ****** Detail (10) ********************************************************************************* 113 SASL authentication failed -------------------------------------------------------------- 113 92.24.80.207 host-92-24-80-207.ppp.as43234.net 113 LOGIN 113 generic failure 195 Miscellaneous warnings ------------------------------------------------------------------ 113 SASL authentication failure: cannot connect to saslauthd server: Permission denied 41 inet_protocols: IPv6 support is disabled: Address family not supported by protocol 41 inet_protocols: configuring for IPv4 support only 2 5xx Reject relay denied ----------------------------------------------------------------- 1 46.242.103.110 unknown 1 [email protected] 1 114.42.142.103 114-42-142-103.dynamic.hinet.net 1 [email protected] 1 Connections lost (inbound) -------------------------------------------------------------- 1 After RCPT 3 Delivered ------------------------------------------------------------------------------- 3 myhost.xx 1 Hostname verification errors ------------------------------------------------------------ 1 Name or service not known 1 46.242.103.110 broadband-46-242-103-110.nationalcablenetworks.ru === Delivery Delays Percentiles ============================================================ 0% 25% 50% 75% 90% 95% 98% 100%

  Read the article

• Microsoft Remote Desktop Services - Android

  - by Matt Rogers

  We have recently started testing Remote Desktop Services. We have deployed the environment using the latest server, Windows Server 2012 R2. We have deployed the Web Access Roles, RD Gateway, Connection Broker Virtualization Host and Session Host. We are running both, Virtual machine-based and Session-based deployments. All of these are working as expected internally and externally when using a Windows workstation as the RDS client, however, the Android client is unable to launch applications. Once you install the app from Google Play you are given a screen to add Remote Resources. After entering the appropriate URL, username and password we see the applications that have been published. Unfortunately, when we attempt to launch an app we get the following error: Connection Error Host not found. Please provide the fully-qualified name or the IP address of the host. We have already entered this information otherwise I don't believe we would be able to see the published applications. I think the error is related to the certificate and how it is being used to connect to the applications. Since this is in our lab environment we have not configured a valid external certificate on the servers and the trusted certificate that is installed on the android tablet points to our internal server / domain name. What I would like to know: Has anyone configured RDS Web Access on Server 2012 R2 and attempted to externally connect an Android or iOS device using the Microsoft supported Remote Desktop client. Are others experiencing the same problem we are? Were you able to resolve the issue? Was it related to the external cert / host name?

  Read the article

• When I log on to my company desktop, I log on to a domain. How is this domain name installed?

  - by learnerforever

  Hi, When I have to work on my machine in company, I have noticed that I log on to a domain (named on the basis of company name) and not really on that computer. From, what I understand, this has a few advantages, the primary being that I just need one password for the domain and can work through any of the machines in company. My questions are : What software on desktop/network have to be installed so that the desktop recognizes and gives me option of logging into a domain. I would guess that a software can be installed on desktop, and there we can configure the IP address of domain server of company and port number, which handles authentication. Is this correct? This takes me to another question that how are softwares installed on end machines in a company. Going to each machine physically and installing looks very unweildy from administrator point of view. An obvious solution would be to install softwares (and updates) over network. My question on this are: What protocols,keywords come into picture when administrator installs OS,softwares,updates from his administrator machine to end machine through network. Thanks,

  Read the article

• Prevent Cisco VPN from interrupting home networking

  - by jkohlhepp

  I just got a new laptop, and for the most part have left its settings alone. Today I was trying to get some sharing going between my desktop and the laptop. Both machines are connected to the same wireless network and both machines consider that network to be a Home network. Both are running Win7 Home Premium. It seems like my laptop is aware of my desktop on the network. It can ping it by IP or by computer name. When I go to Network from the laptop, I can see the desktop in the list of computers. However, my desktop cannot ping the laptop, nor can it see it within Network. My desktop has a Homegroup set up, but my laptop says "There is currently no homegroup on the network". I do have network discovery turned on for both machines. Why can my desktop not "talk" to my laptop but it works the other way around? Update: Disabling the Windows Firewall on the laptop somewhat fixes the problem. With it disabled, my desktop can ping my laptop, but still my laptop can't see the homegroup. Also, it can ping via hostname, which resolves to IPv6, but can't ping via the IPv4 address. Obviously I'd rather not leave my firewall disabled, so I need a more specific fix. Update 2: Aha! It is the Cisco VPN software I was running to connect to work computers. Once I disconnected and exited from that, the two PCs seemed to be talking normally and the homegroup was visible to the laptop. So now my question has morphed: how can I prevent Cisco VPN from interrupting my home networking?

  Read the article

< Previous Page | 375 376 377 378 379 380 381 382 383 384 385 386  | Next Page >