Search Results

Search found 2237 results on 90 pages for 'fxo gateway'.

Page 38/90 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

• I have just created a subnet for a local network, connecting to a standalone server on another network, now I cannot connect to the internet

  - by Seth

  I am just learning some new aspects of servers and networking. We have a network of 5 subnets that all interconnect with each-other. In order to get two computers on the subnet that we were setting up, I changed the IP from the subnet where the standalone server is on (where they used to be set up)to the local subnet we are remotely hooking up. Likewise I also changed the gateway to coincide with the new subnet. Only problem is that since doing this, I am unable to establish a connection to the internet. I can ping the server and correspong gateway & DNS server, but cannot get connected to the internet. We do have a dumb-switch (non-programmable) connected that receives both the internet and private network inputs and distributes (or should do so) to about 5 other computers. Bottom line, I cannot currently connect to the internet, and am wondering what could be causing this.. It is likely something very obvious and pardon me being more vague than I probably should be, but I could use some help resolving this! Thanks for any help!

  Read the article

• Configuring two subnets with two NICS. Access from a NAS to the internet

  - by archipestre

  I am having trouble configuring my NAS. I have a DSL router with WIFI (192.168.1.1) in my flatmates room. In my room I have a server with two NICS: 1) wlan0 (192.168.1.2) that connects to the DSL router via wireless 2) em1 (192.168.0.1) that connects to the NAS (192.168.0.20) with a crossover cable. I have Fedora 17 and I have enable packet forwarding. My IP configuration is as follows: WLAN0 inet 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 EM1 inet 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 My routing table looks like: Destination Gateway G enmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 em1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 I have enable a static route in the DSL server: Status Network Destination Subnet Mask Interface Gateway Remove Edit Active 192.168.0.0 255.255.255.0 LAN 192.168.1.2 From my server I can ping the DSL router and the NAS. From the NAS I can ping both NICS of the server. However the NAS is unable to ping the DSL router or any address in the Internet. Any idea of what is wrong. Thank you in advance

  Read the article

• Slow network interaction between 2 kvm host machines

  - by VirtualNoob

  We have 2 physical machines, Host1 is a CentOS 6.4 kvm host and hosts ~7 kvm VMs all running Ubuntu 12.04 - all of this runs perfectly. Recently we've added a 2nd host system, host2, again a CentOS 6.4 kvm host with a view to running another couple of VMs and providing some failover against host1 should it be required. Both physical machines reside in the same cabinet in our DC, and are on the same subnet - let's say host1: 1.1.1.64 and host2: 1.1.1.81. Both have their gateway set to the DC gateway of 1.1.1.254 with no hardware firewall in between. On each machine, I have 4 NICs that are bonded together to form a single interface, which is then bridged to allow the VMs to access the network. All of the VMs are online, and all of them can successfully ssh into the hosts without any delay. Both systems can access the internet fine, and I can ssh into both systems from home without any issues. However, there is a real delay when attempting to ssh from host1 to host2 (or vice versa) and this obviously means that any action required on host2, that is controlled by host1 either takes forever or results in failure due to timeout. In the interest of keeping this post short, I've put my ifcfg files into a pastie: http://pastie.org/8081648 I've tried both adding a firewall rule in each machine for the other, and also disabling the firewall entirely, so that can't be the issue. I've tried troubleshooting this myself but can't seem to get to the bottom of it. Any help or advice would be appreciated. Thanks in advance.

  Read the article

• SSH connection times out

  - by mark

  Given: vm - a WinXPsp3 virtual machine hosted by a Win7sp1 physical machine alice is the user on vm srv - a Win2008R2sp1 server bob is the user on srv quake - a linux server mark is the user on quake Both vm and srv have the same new installation of cygwin (1.7.9) and openssh. Firewall service is disabled on vm (and its host) and on srv All the machines can be pinged from all the machines. ssh mark@quake works OK from both vm and srv. ssh bob@srv works OK from both quake and vm. ssh alice@vm works on the vm itself only, but it fails on the other two machines: alice@vm ~ $ ssh alice@vm alice@vm's password: Last login: Tue Oct 25 23:42:09 2011 from vm.shunra.net [mark@Quake ~]$ ssh -vvv alice@vm OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to vm [172.30.2.60] port 22. debug1: connect to address 172.30.2.60 port 22: Connection timed out ssh: connect to host vm port 22: Connection timed out bob@Srv ~ $ ssh -vvv alice@vm OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Connecting to vm [172.30.2.60] port 22. debug1: connect to address 172.30.2.60 port 22: Connection timed out ssh: connect to host vm port 22: Connection timed out I used ssh-host-config both on vm and srv to configure the ssh to run as a windows service. Besides that I did nothing else. Can anyone help me troubleshoot this issue? Thank you very much. EDIT The virtual machine software is VMWare Workstation 7.1.4. I think the problem is in its settings, but I have no idea where exactly. The Network Adapter is set to Bridged. EDIT2 All the machines are located in the company lab, I think all of them are on the same segment, but I may be wrong. Below is the ipconfig /all output for each machine (skipping the linux server). I have deleted the Tunnel adapters to keep the output minimal. If anyone thinks they matter, do tell so and I will post them as well. In addition ping output is given to show that DNS is correct. Something else, may be relevant, may be not. Doing psexec to srv works OK, whereas to vm failes with Access Denied. srv: C:\Windows\system32>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : srv Primary Dns Suffix . . . . . . . : shunra.net Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : shunra.net Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom BCM5709C NetXtreme II GigE (NDIS VBD Client) Physical Address. . . . . . . . . : E4-1F-13-6D-F3-00 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 172.30.6.9(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.248.0 Default Gateway . . . . . . . . . : 172.30.0.254 DNS Servers . . . . . . . . . . . : 172.30.1.1 172.30.1.2 NetBIOS over Tcpip. . . . . . . . : Enabled C:\Windows\system32>ping vm Pinging vm.shunra.net [172.30.2.60] with 32 bytes of data: Reply from 172.30.2.60: bytes=32 time=1ms TTL=128 Reply from 172.30.2.60: bytes=32 time=4ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.2.60: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 4ms, Average = 1ms C:\Windows\system32> vm: C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : vm Primary Dns Suffix . . . . . . . : shunra.net Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : shunra.net shunranet Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : shunranet Description . . . . . . . . . . . : VMware Accelerated AMD PCNet Adapter Physical Address. . . . . . . . . : 00-0C-29-8F-A0-0B Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 172.30.2.60 Subnet Mask . . . . . . . . . . . : 255.255.248.0 Default Gateway . . . . . . . . . : 172.30.0.254 DHCP Server . . . . . . . . . . . : 172.30.1.1 DNS Servers . . . . . . . . . . . : 172.30.1.1 172.30.1.2 Lease Obtained. . . . . . . . . . : Tuesday, October 25, 2011 18:16:34 Lease Expires . . . . . . . . . . : Wednesday, November 02, 2011 18:16:34 C:\>ping srv Pinging srv.shunra.net [172.30.6.9] with 32 bytes of data: Reply from 172.30.6.9: bytes=32 time=1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.6.9: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\> vm-host (the host machine of the vm): C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : vm-host Primary Dns Suffix . . . . . . . : shunra.net Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : shunra.net Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC (NDIS 6.20) Physical Address. . . . . . . . . : 6C-F0-49-E7-E9-30 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f59d:7f6e:1510:6f%10(Preferred) IPv4 Address. . . . . . . . . . . : 172.30.6.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.248.0 Default Gateway . . . . . . . . . : 172.30.0.254 DHCPv6 IAID . . . . . . . . . . . : 242020425 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-CC-39-80-6C-F0-49-E7-E9-30 DNS Servers . . . . . . . . . . . : 172.30.1.1 194.90.1.5 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::cd92:38c0:9a6d:c008%16(Preferred) Autoconfiguration IPv4 Address. . : 169.254.192.8(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 352342102 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-CC-39-80-6C-F0-49-E7-E9-30 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::edb9:b78c:a504:593b%17(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.5.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 369119318 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-CC-39-80-6C-F0-49-E7-E9-30 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled C:\>ping srv Pinging srv.shunra.net [172.30.6.9] with 32 bytes of data: Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.6.9: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping vm Pinging vm.shunra.net [172.30.2.60] with 32 bytes of data: Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.2.60: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\> EDIT3 I have just checked - the vm-host is able to ssh to the vm machine! I still do not know how to leverage this discovery to solve the problem.

  Read the article

• How to use CLEAR USB internet connection in Ubuntu (host) and WindowsXP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for linux as yet. I've installed windowsxp as guest in ubuntu and the version I'm using is 3.2.2. USB is connecting fine in WindowsXP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• Bridging LXC containers to host eth0 so they can have a public IP

  - by Vianney Stroebel

  UPDATE: I found the solution there: http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge#No_traffic_gets_trough_.28except_ARP_and_STP.29 # cd /proc/sys/net/bridge # ls bridge-nf-call-arptables bridge-nf-call-iptables bridge-nf-call-ip6tables bridge-nf-filter-vlan-tagged # for f in bridge-nf-*; do echo 0 $f; done But I'd like to have expert opinions on this: is it safe to disable all bridge-nf-*? What are they here for? END OF UPDATE I need to bridge LXC containers to the physical interface (eth0) of my host, reading numerous tutorials, documents and blog posts on the subject. I need the containers to have their own public IP (which I've previously done KVM/libvirt). After two days of searching and trying, I still can't make it work with LXC containers. The host runs a freshly installed Ubuntu Server Quantal (12.10) with only libvirt (which I'm not using here) and lxc installed. I created the containers with : lxc-create -t ubuntu -n mycontainer So they also run Ubuntu 12.10. Content of /var/lib/lxc/mycontainer/config is: lxc.utsname = mycontainer lxc.mount = /var/lib/lxc/test/fstab lxc.rootfs = /var/lib/lxc/test/rootfs lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.veth.pair = vethmycontainer lxc.network.ipv4 = 179.43.46.233 lxc.network.hwaddr= 02:00:00:86:5b:11 lxc.devttydir = lxc lxc.tty = 4 lxc.pts = 1024 lxc.arch = amd64 lxc.cap.drop = sys_module mac_admin mac_override lxc.pivotdir = lxc_putold # uncomment the next line to run the container unconfined: #lxc.aa_profile = unconfined lxc.cgroup.devices.deny = a # Allow any mknod (but not using the node) lxc.cgroup.devices.allow = c *:* m lxc.cgroup.devices.allow = b *:* m # /dev/null and zero lxc.cgroup.devices.allow = c 1:3 rwm lxc.cgroup.devices.allow = c 1:5 rwm # consoles lxc.cgroup.devices.allow = c 5:1 rwm lxc.cgroup.devices.allow = c 5:0 rwm #lxc.cgroup.devices.allow = c 4:0 rwm #lxc.cgroup.devices.allow = c 4:1 rwm # /dev/{,u}random lxc.cgroup.devices.allow = c 1:9 rwm lxc.cgroup.devices.allow = c 1:8 rwm lxc.cgroup.devices.allow = c 136:* rwm lxc.cgroup.devices.allow = c 5:2 rwm # rtc lxc.cgroup.devices.allow = c 254:0 rwm #fuse lxc.cgroup.devices.allow = c 10:229 rwm #tun lxc.cgroup.devices.allow = c 10:200 rwm #full lxc.cgroup.devices.allow = c 1:7 rwm #hpet lxc.cgroup.devices.allow = c 10:228 rwm #kvm lxc.cgroup.devices.allow = c 10:232 rwm Then I changed my host /etc/network/interfaces to: auto lo iface lo inet loopback auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 92.281.86.226 netmask 255.255.255.0 network 92.281.86.0 broadcast 92.281.86.255 gateway 92.281.86.254 dns-nameservers 213.186.33.99 dns-search ovh.net When I try command line configuration ("brctl addif", "ifconfig eth0", etc.) my remote host becomes inaccessible and I have to hard reboot it. I changed the content of /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces to: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 179.43.46.233 netmask 255.255.255.255 broadcast 178.33.40.233 gateway 92.281.86.254 It takes several minutes for mycontainer to start (lxc-start -n mycontainer). I tried replacing gateway 92.281.86.254 by : post-up route add 92.281.86.254 dev eth0 post-up route add default gw 92.281.86.254 post-down route del 92.281.86.254 dev eth0 post-down route del default gw 92.281.86.254 My container then starts instantly. But whatever configuration I set in /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces, I cannot ping from mycontainer to any IP (including the host's) : ubuntu@mycontainer:~$ ping 92.281.86.226 PING 92.281.86.226 (92.281.86.226) 56(84) bytes of data. ^C --- 92.281.86.226 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5031ms And my host cannot ping the container: root@host:~# ping 179.43.46.233 PING 179.43.46.233 (179.43.46.233) 56(84) bytes of data. ^C --- 179.43.46.233 ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4000ms My container's ifconfig: ubuntu@mycontainer:~$ ifconfig eth0 Link encap:Ethernet HWaddr 02:00:00:86:5b:11 inet addr:179.43.46.233 Bcast:255.255.255.255 Mask:0.0.0.0 inet6 addr: fe80::ff:fe79:5a31/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:6 overruns:0 frame:0 TX packets:54 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4070 (4.0 KB) TX bytes:4168 (4.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2496 (2.4 KB) TX bytes:2496 (2.4 KB) My host's ifconfig: root@host:~# ifconfig br0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b inet addr:92.281.86.226 Bcast:91.121.67.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe43:652b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1453 errors:0 dropped:18 overruns:0 frame:0 TX packets:1630 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145125 (145.1 KB) TX bytes:299943 (299.9 KB) eth0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3178 errors:0 dropped:0 overruns:0 frame:0 TX packets:1637 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:298263 (298.2 KB) TX bytes:309167 (309.1 KB) Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:300 (300.0 B) TX bytes:300 (300.0 B) vethtest Link encap:Ethernet HWaddr fe:0d:7f:3e:70:88 inet6 addr: fe80::fc0d:7fff:fe3e:7088/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4168 (4.1 KB) TX bytes:4250 (4.2 KB) virbr0 Link encap:Ethernet HWaddr de:49:c5:66:cf:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I have disabled lxcbr0 (USE_LXC_BRIDGE="false" in /etc/default/lxc). root@host:~# brctl show bridge name bridge id STP enabled interfaces br0 8000.4c72b943652b no eth0 vethtest I have configured the IP 179.43.46.233 to point to 02:00:00:86:5b:11 in my hosting provider (OVH) config panel. (The IPs in this post are not the real ones.) Thanks for reading this long question! :-) Vianney

  Read the article

• How to use CLEAR USB WiMax in Ubuntu (host) and Windows XP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for Linux as yet. I've installed Windows XP as guest in Ubuntu and the version I'm using is 3.2.2. USB is connecting fine in Windows XP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• Citrix Xen VM's lose networking

  - by Ash

  My client has a XenServer 6.0.2 installation with 2 Window Server 2008 R2 virtual machines. Whenever the virtual machines are rebooted they lose their IP settings (IP address, subnet, gateway). Each time after a reboot I need to login to each VM via XenCenter and re-apply the required static IP settings. This causes issues with connected iSCSI drives within each VM - drives need to be reconnected after each reboot. For example, a network adapter has the following settings pre-reboot: Description . . . . . . . . . . . : Citrix PV Ethernet Adapter #0 Physical Address. . . . . . . . . : C6-FB-A2-4F-2C-F3 IPv4 Address. . . . . . . . . . . : 10.101.0.101(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.101.0.10 DNS Servers . . . . . . . . . . . : 10.101.0.100 NetBIOS over Tcpip. . . . . . . . : Enabled Post-reboot: Description . . . . . . . . . . . : Citrix PV Ethernet Adapter #0 Physical Address. . . . . . . . . : C6-FB-A2-4F-2C-F3 Autoconfiguration IPv4 Address. . : 169.254.153.174(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 10.101.0.100 NetBIOS over Tcpip. . . . . . . . : Enabled Under XenCenter -- Virtual Network Interfaces, each adapter is set to a static MAC address (i.e. "Use this MAC address"). I have tried the following commands within one VM but this had no effect: netsh winsock reset catalog netsh int ip reset Can someone please help?

  Read the article

• Why does my ping command (Windows) results alternate between "timeout" and "network is not reachable"?

  - by Sopalajo de Arrierez

  My Windows is in Spanish, so I will have to paste console outputs in that language (I think that translating without knowing the exact terms used in english versions could give worse results than leaving it as it appears on screen). This is the issue: when pinging a non-existent IP from a WinXP-SP3 machine (clean Windows install, just formatted), I get sometimes a "Timeout" result, and sometimes a "network is not reachable" message. This is the result of: ping 192.168.210.1 Haciendo ping a 192.168.210.1 con 32 bytes de datos: Tiempo de espera agotado para esta solicitud. Respuesta desde 80.58.67.86: Red de destino inaccesible. Respuesta desde 80.58.67.86: Red de destino inaccesible. Tiempo de espera agotado para esta solicitud. Estadísticas de ping para 192.168.210.1: Paquetes: enviados = 4, recibidos = 2, perdidos = 2 (50% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms 192.168.210.1 does not exist on the network. DHCP client is enabled, and the computer gets assigned those network config by the router. My IP: 192.168.11.2 Netmask: 255.255.255.0 Gateway: 192.168.11.1 DNS: 80.58.0.33/194.224.52.36 This is the output from "route print command": =========================================================================== Rutas activas: Destino de red Máscara de red Puerta de acceso Interfaz Métrica 0.0.0.0 0.0.0.0 192.168.11.1 192.168.11.2 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.11.0 255.255.255.0 192.168.11.2 192.168.11.2 20 192.168.11.2 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.11.255 255.255.255.255 192.168.11.2 192.168.11.2 20 224.0.0.0 240.0.0.0 192.168.11.2 192.168.11.2 20 255.255.255.255 255.255.255.255 192.168.11.2 192.168.11.2 1 255.255.255.255 255.255.255.255 192.168.11.2 3 1 Puerta de enlace predeterminada: 192.168.11.1 =========================================================================== Rutas persistentes: ninguno The output of: ping 1.1.1.1 Haciendo ping a 1.1.1.1 con 32 bytes de datos: Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Estadísticas de ping para 1.1.1.1: Paquetes: enviados = 4, recibidos = 0, perdidos = 4 1.1.1.1 does not exist on the network. and the output of: ping 10.1.1.1 Haciendo ping a 10.1.1.1 con 32 bytes de datos: Respuesta desde 80.58.67.86: Red de destino inaccesible. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Respuesta desde 80.58.67.86: Red de destino inaccesible. Estadísticas de ping para 10.1.1.1: Paquetes: enviados = 4, recibidos = 2, perdidos = 2 (50% perdidos), 10.1.1.1 does not exist on the network. I can do some aproximate translation of what you demand if necessary. I have another computers in the same network (WinXP-SP3 and Win7-SP1), and they have, too, this problem. Gateway (Router): Buffalo WHR-HP-GN (official Buffalo firmware, not DD-WRT). I have some Linux (Debian/Kali) machine in my network, so I tested things on it: ping 192.168.210.1 PING 192.168.210.1 (192.168.210.1) 56(84) bytes of data. From 80.58.67.86 icmp_seq=1 Packet filtered From 80.58.67.86 icmp_seq=2 Packet filtered From 80.58.67.86 icmp_seq=3 Packet filtered From 80.58.67.86 icmp_seq=4 Packet filtered to the non-existing 1.1.1.1 : ping 1.1.1.1 PING 1.1.1.1 (1.1.1.1) 56(84) bytes of data. ^C --- 1.1.1.1 ping statistics --- 153 packets transmitted, 0 received, 100% packet loss, time 153215ms (no response after waiting a few minutes). and the non-existing 10.1.1.1: ping 10.1.1.1 PING 10.1.1.1 (10.1.1.1) 56(84) bytes of data. From 80.58.67.86 icmp_seq=20 Packet filtered From 80.58.67.86 icmp_seq=22 Packet filtered From 80.58.67.86 icmp_seq=23 Packet filtered From 80.58.67.86 icmp_seq=24 Packet filtered From 80.58.67.86 icmp_seq=25 Packet filtered What is going on here? I am posing this question mainly for learning purposes, but there is another reason: when all pings are returning "timeout", it creates an %ERRORLEVEL% value of 1, but if there is someone of "Network is not reachable" type, %ERRORLEVEL% goes to 0 (no error), and this could be inappropriate for a shell script (we can not use ping to detect, for example, if the network is down due to loss of contact with the gateway).

  Read the article

• CodePlex Daily Summary for Sunday, October 28, 2012

  CodePlex Daily Summary for Sunday, October 28, 2012Popular ReleasesPlayer Framework by Microsoft: Player Framework for Windows 8 (Preview 7): This release is compatible with the version of the Smooth Streaming SDK released today (10/26). Release 1 of the player framework is expected to be available next week. IMPROVEMENTS & FIXESIMPORTANT: List of breaking changes from preview 6 Support for the latest smooth streaming SDK. Xaml only: Support for moving any of the UI elements outside the MediaPlayer (e.g. into the appbar). Note: Equivelent changes to the JS version due in coming week. Support for localizing all text used in t...Send multiple SMS via Way2SMS C#: SMS 1.1: Added support for 160by2Quick Launch: Quick Launch 1.0: A Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsPress Win+Q and start to search and run. http://www.codeplex.com/Download?ProjectName=quicklaunch&DownloadId=523536Orchard Project: Orchard 1.6: Please read our release notes for Orchard 1.6: http://docs.orchardproject.net/Documentation/Orchard-1-6-Release-Notes Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you will pollute the rating, and you won't get an answer.ZXMAK2: Version 2.6.7.0: - small performance improvements - fix & improvements for Direct3D renderer (thanks to zebest for testing)Media Companion: Media Companion 3.507b: Once again, it has been some time since our release, and there have been a number changes since then. It is hoped that these changes will address some of the issues users have been experiencing, and of course, work continues! New Features: Added support for adding Home Movies. Option to sort Movies by votes. Added 'selectedBrowser' preference used when opening links in an external browser. Added option to fallback to getting runtime from the movie file if not available on IMDB. Added new Big...MSBuild Extension Pack: October 2012: Release Blog Post The MSBuild Extension Pack October 2012 release provides a collection of over 475 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUI...NAudio: NAudio 1.6: Release notes at http://mark-dot-net.blogspot.co.uk/2012/10/naudio-16-release-notes-10th.htmlPowerShell Community Extensions: 2.1 Production: PowerShell Community Extensions 2.1 Release NotesOct 25, 2012 This version of PSCX supports both Windows PowerShell 2.0 and 3.0. See the ReleaseNotes.txt download above for more information.Umbraco CMS: Umbraco 4.9.1: Umbraco 4.9.1 is a bugfix release to fix major issues in 4.9.0 BugfixesThe full list of fixes can be found in the issue tracker's filtered results. A summary: Split buttons work again, you can now also scroll easier when the list is too long for the screen Media and Content pickers have information of the full path of the picked item Fixed: Publish status may not be accurate on nodes with large doctypes Fixed: 2 media folders and recycle bins after upgrade to 4.9 The template/code ...AcDown????? - AcDown Downloader Framework: AcDown????? v4.2.2: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown??????????????????，????????????????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ???? 32??64? ???Linux ????(1)????????Windows XP???，????????.NET Framework 2.0???(x86)，?????"?????????"??? (2)???????????Linux???，????????Mono?? ??2...Rawr: Rawr 5.0.2: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...MCEBuddy 2.x: MCEBuddy 2.3.5: Changelog for 2.3.5 (32bit and 64bit) 1. Fixed a bug causing MCEBuddy to crash during or after installation on Windows XP 2. Bugfix for resource leak with UPnP which would lead to a failure after many days 3. Increased the UPnP discovery re-scan interval from 10 minutes to 30 minutes 4. Added support for specifying TVDB and IMDB id’s in the conversion task page (forcing the internet lookup for metadata)CRM 2011 Visual Ribbon Editor: Visual Ribbon Editor (1.3.1025.5): [NEW] Support for connecting to CRM Online via Office 365 (OSDP) [NEW] Current connection information and loaded ribbon name are displayed in the status bar [IMPROVED] Connect dialog minor improvements and error message descriptions [IMPROVED] Connecting to a CRM server will close currently loaded ribbon upon confirmation (if another ribbon was loaded previously) [FIX] Fixed bug in Open Ribbon dialog which would not allow to refresh entity list more than onceReadable Passphrase Generator: KeePass Plugin 0.8.0: Changes: Interrogative phrases (questions) like why did the statesman burgle amidst lucid sunlamps Support transitive / intransitive verbs (whether a verb needs a subject or not). Change adverbs to be either before or after the verb, at random. Add an "equal" version of each strength, where each possibility is equally likely (for password purists). 3401 words in the default dictionary (~400 more than previous release) Fixed bugs when choosing verb tenseseWay payment gateway provider for NB_Store: NB_Store_Gateway_eWay: Install package for eWAY gateway for NB_Store.fastJSON: v2.0.9: - added support for root level DataSet and DataTable deserialize (you have to do ToObject<DataSet>(...) ) - added dataset testsMicrosoft Ajax Minifier: Microsoft Ajax Minifier 4.72: Fix for Issue #18819 - bad optimization of return/assign operator.WPF Application Framework (WAF): WPF Application Framework (WAF) 2.5.0.390: Version 2.5.0.390 (Release Candidate): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Changelog Legend: [B] Breaking change; [O] Marked member as obsolete WAF: Fix recent file list remove issue. WAF: Minor code improvements. BookLibrary: Fix Blend design time support o...Fiskalizacija za developere: FiskalizacijaDev 1.1: Ovo je prva nadogradnja ovog projekta nakon inicijalnog predstavljanja - dodali smo nekoliko feature-a, bilo zato što smo sami primijetili da bi ih bilo dobro dodati, bilo na osnovu vaših sugestija - hvala svima koji su se ukljucili :) Ovo su stvari riješene u v1.1.: 1. Bilo bi dobro da se XML dokument koji se šalje u CIS može snimiti u datoteku (http://fiskalizacija.codeplex.com/workitem/612) 2. Podrška za COM DLL (VB6) (http://fiskalizacija.codeplex.com/workitem/613) 3. Podrška za DOS (unu...New ProjectsAnalytics for Windows 8: SIlverlight / WPF User control integrated in WPF / SILVERLIGHT / WINDOWS PHONE Apps in order to collect user data ( Action , Timespan etc ) . bGui - User Interfaces in Batch: A small project for allowing basic user interface creation in batch. Still under strict development, see documentation for current functionality.Blog Projects: Projects wich i use in my blog postsCloud Sync Service: This Windows Service lets you sync your files across other machines by using Cloud File Storage as gateway. Amazon S3 and Windows Azure supported.CocoaVP8: CocoaVP8 is a dual-licensed commercial/GPL native library which allows Mac and iOS applications to easily use the VP8 video codec.DarkSky Orchard Microdata: Microdata is an Orchard module that exposes a MicrodataPart that will render microdata for your content items.Gerenciador Paroquial: Um conjunto de ferramentas desenvolvido para auxiliar a administração de comunidades eclesiásticas episcopais.Quick Launch: Quick Launch - a New Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsRDI Alef: RDI ALEF (ALef Entities Framework) é uma biblioteca desenvolvida em C# para persistência de objetos em um banco de dados. Encapsula um manipulador SQL e o funciSend multiple SMS via Way2SMS C#: Way2SMS, 160BY2, SMS, INDIATrending: Trending program; calculates the highest and lowest changes in frequency of specific words in two files.

  Read the article

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• DevConnections Slides and Samples Posted

  - by Rick Strahl

  I’ve posted the slides and samples to my DevConnections Sessions for anyone interested. I had a lot of fun with my sessions this time around mainly because the sessions picked were a little off the beaten track (well, the handlers/modules and e-commerce sessions anyway). For those of you that attended I hope you found the sessions useful. For the rest of you – you can check out the slides and samples if you like. Here’s what was covered: Introduction to jQuery with ASP.NET This session covered mostly the client side of jQuery demonstrated on a small sample page with a variety of incrementally built up examples of selection and page manipulation. This session also introduces some of the basics of AJAX communication talking to ASP.NET. When I do this session it never turns out exactly the same way and this time around the examples were on the more basic side and purely done with hands on demonstrations rather than walk throughs of more complex examples. Alas this session always feels like it needs another half an hour to get through the full sortiment of functionality. The slides and samples cover a wider variety of topics and there are many examples that demonstrate more advanced operations like interacting with WCF REST services, using client templating and building rich client only windowed interfaces. Download Low Level ASP.NET: Handlers and Modules This session was a look at the ASP.NET pipeline and it discusses some of the ASP.NET base architecture and key components from HttpRuntime on up through the various modules and handlers that make up the ASP.NET/IIS pipeline. This session is fun as there are a number of cool examples that demonstrate the power and flexibility of ASP.NET, but some of the examples were external and interfacing with other technologies so they’re not actually included in the downloadable samples. However, there are still a few cool ones in there – there’s an image resizing handler, an image overlay module that stamps images with Sample if loaded from a certain folder, an OpenID authentication module (which failed during the demo due to the crappy internet connection at DevConnections this year :-}), Response filtering using a generic filter stream component, a generic error handler and a few others. The slides cover a lot of the ASP.NET pipeline flow and various HttpRuntime components. Download Electronic Payment Processing in ASP.NET Applications This session covered the business end and integration of electronic credit card processing and PayPal. A good part of this session deals with what’s involved in payment processing, getting signed up and who you have to deal with for your merchant account. We then took a look at integration of credit card processing via some generic components provided with the session that allow processing using a unified class interface with specific implementations for several of the most common gateway providers including Authorize.NET, PayFlowPro, LinkPoint, BluePay etc. We also briefly looked at PayPal Classic implementation which provides a quick and cheap if not quite as professional mechanism for taking payments online. The samples provide the Credit Card processing wrappers for the various gateway providers as well as a PayPal helper class to generate the PayPal redirect urls as well as helper code for dealing with IPN callbacks. Download Hope some of you will find the material useful. Enjoy.© Rick Strahl, West Wind Technologies, 2005-2010Posted in ASP.NET  

  Read the article

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• Charset and POST request

  - by jriff

  Hi All! I have a Rails 2.3.5 application that is working fine with UTF-8 and international characters. Now I have made some integration to a payment gateway where I POST some data, wait a while and get a POST back. The problem is that when I get that post back the international characters are broken. Instead of "sørensen" I get: "sørensen". If I do an iconv -fISO-8859-1 -tUTF8 it gets correctly converted to the former (I do that from a OS X command prompt). I have examined the POST request with logger.info(request.headers.inspect) in my controller and I can see that no charset parameter is given. As far as I can see the POST from the gateway must be UTF8 since one character (ø) gets translated to two (ø). So why does Rails think that the POST is ISO-8859-1? I know that one solution is to simply convert the params-hash with Iconv in the controller but I would like to know what is happening. Thanks in advance. Regards, Jacob

  Read the article

• iPhone SDK Push notification randomly fails

  - by Jameson

  I have a PHP file with the following content that works perfectly on development ceritficates, but when I switch to a production certificate the PHP errors and gives the below message, but it only does this about 50% of the time. The other 50% it works. Anyone know why this might be happening? <?php // masked for security reason $deviceToken = 'xxxxxx'; // jq $ctx = stream_context_create(); stream_context_set_option($ctx, 'ssl', 'local_cert', dirname(__FILE__)."/prod.pem"); $number = 5; $fp = stream_socket_client('ssl://gateway.push.apple.com:2195', $err, $errstr, 60, STREAM_CLIENT_CONNECT, $ctx); if (!$fp) { print "Failed to connect $err $errstr\n"; } else { print "Connection OK\n"; $msg = $_GET['msg']; $payload['aps'] = array('alert' => $msg, 'badge' => 1, 'sound' => 'default'); $payload = json_encode($payload); $msg = chr(0) . pack("n",32) . pack('H*', str_replace(' ', '', $deviceToken)) . pack("n",strlen($payload)) . $payload; print "sending message :" . $payload . "\n"; fwrite($fp, $msg); fclose($fp); } ?> The PHP error: Warning: stream_socket_client() [function.stream-socket-client]: Unable to set local cert chain file `/var/www/vhosts/thissite.com/httpdocs/prod.pem'; Check that your cafile/capath settings include details of your certificate and its issuer in /var/www/vhosts/thissite.com/httpdocs/pushMessageLive.php on line 19 Warning: stream_socket_client() [function.stream-socket-client]: failed to create an SSL handle in /var/www/vhosts/thissite.com/httpdocs/pushMessageLive.php on line 19 Warning: stream_socket_client() [function.stream-socket-client]: Failed to enable crypto in /var/www/vhosts/thissite.com/httpdocs/pushMessageLive.php on line 19 Warning: stream_socket_client() [function.stream-socket-client]: unable to connect to ssl://gateway.sandbox.push.apple.com:2195 (Unknown error) in /var/www/vhosts/thissite.com/httpdocs/pushMessageLive.php on line 19 Failed to connect 0

  Read the article

• Problem executing script using Python and subprocces.call yet works in Bash

  - by Antoine Benkemoun

  Hello, For the first time, I am asking a little bit of help over here as I am more of a ServerFault person. I am doing some scripting in Python and I've been loving the language so far yet I have this little problem which is keeping my script from working. Here is the code line in question : subprocess.call('xen-create-image --hostname '+nom+' --memory '+memory+' --partitions=/root/scripts/part.tmp --ip '+ip+' --netmask '+netmask+' --gateway '+gateway+' --passwd',shell=True) I have tried the same thing with os.popen. All the variables are correctly set. When I execute the command in question in my regular Linux shell, it works perfectly fine but when I execute it using my Python scripts, I get bizarre errors. I even replaced subprocess.call() by the print function to make sure I am using the exact output of the command. I went looking into environment variables of my shell but they are pretty much the same... I'll post the error I am getting but I'm not sure it's relevant to my problem. Use of uninitialized value $lines[0] in substitution (s///) at /usr/share/perl5/Config/IniFiles.pm line 614. Use of uninitialized value $_ in pattern match (m//) at /usr/share/perl5/Config/IniFiles.pm line 628. I am not a Python expert so I'm most likely missing something here. Thank you in advance for your help, Antoine

  Read the article

• PHP: Aggregate Model Classes or Uber Model Classes?

  - by sunwukung

  In many of the discussions regarding the M in MVC, (sidestepping ORM controversies for a moment), I commonly see Model classes described as object representations of table data (be that an Active Record, Table Gateway, Row Gateway or Domain Model/Mapper). Martin Fowler warns against the development of an anemic domain model, i.e. a class that is nothing more than a wrapper for CRUD functionality. I've been working on an MVC application for a couple of months now. The DBAL in the application I'm working on started out simple (on account of my understanding - oh the benefits of hindsight), and is organised so that Controllers invoke Business Logic classes, that in turn access the database via DAO/Transaction Scripts pertinent to the task at hand. There are a few "Entity" classes that aggregate these DAO objects to provide a convenient CRUD wrapper, but also embody some of the "behaviour" of that Domain concept (for example, a user - since it's easy to isolate). Taking a look at some of the code, and thinking along refactoring some of the code into a Rich Domain Model, it occurred to me that were I to try and wrap the CRUD routines and behaviour of say, a Company into a single "Model" class, that would be a sizeable class. So, my question is this: do Models represent domain objects, business logic, service layers, all of the above combined? How do you go about defining the responsibilities for these components?

  Read the article

• Systems design question: DB connection management in load-balanced n-tier

  - by aoven

  I'm wondering about the best approach to designing a DB connection manager for a load-balanced n-tier system. Classic n-tier looks like this: Client -> BusinessServer -> DBServer A load-balancing solution as I see it would then look like this: +--> ... +--+ +--> BusinessServer +--+--> SessionServer --+ Client -> Gateway --+--> BusinessServer +--| +--> DBServer +--> BusinessServer +--+--------------------+ +--> ... +--+ As pictured, the business server component is being load-balanced via multiple instances, and a hardware gateway is distributing the load among them. Session server probably needs to be situated outside the load-balancing array, because it manages state, which mustn't be duplicated. Barring any major errors in design so far, what is the best way to implement DB connection management? I've come up with a couple of options, but there may be others I'm not aware of: Introduce a new Broker component between the DBServer and the other components and let it handle the DB connections. The upside is that all the connections can be managed from a single point, which is very convenient. The downside is that now there is an additional "single point of failure" in the system. Other components must go through it for every request that involves DB in some way, which also makes this a bottleneck. Move the DB connection management into BusinessServer and SessionServer components and let each handle its own DB connections. The upside is that there is no additional "single point of failure" or bottleneck components. The downside is that there is also no control over possible conflicts and deadlocks apart from what DBServer itself can provide. What else can be done? FWIW: Technology is .NET, but none of the vendor-specific stacks are used (e.g. no WCF, MSMQ or the like).

  Read the article

• How do I correctly decode unicode parameters passed to a servlet

  - by Grant Wagner

  Suppose I have: <a href="http://www.yahoo.com/" target="_yahoo" title="Yahoo!&#8482;" onclick="return gateway(this);">Yahoo!</a> <script type="text/javascript"> function gateway(lnk) { window.open(SERVLET + '?external_link=' + encodeURIComponent(lnk.href) + '&external_target=' + encodeURIComponent(lnk.target) + '&external_title=' + encodeURIComponent(lnk.title)); return false; } </script> I have confirmed external_title gets encoded as Yahoo!%E2%84%A2 and passed to SERVLET. If in SERVLET I do: Writer writer = response.getWriter(); writer.write(request.getParameter("external_title")); I get Yahoo!â„¢ in the browser. If I manually switch the browser character encoding to UTF-8, it changes to Yahoo!TM (which is what I want). So I figured the encoding I was sending to the browser was wrong (it was Content-type: text/html; charset=ISO-8859-1). I changed SERVLET to: response.setContentType("text/html; charset=utf-8"); Writer writer = response.getWriter(); writer.write(request.getParameter("external_title")); Now the browser character encoding is UTF-8, but it outputs Yahoo!â?¢ and I can't get the browser to render the correct character at all. My question is: is there some combination of Content-type and/or new String(request.getParameter("external_title").getBytes(), "UTF-8"); and/or something else that will result in Yahoo!TM appearing in the SERVLET output?

  Read the article

• wxPython - ListCrtl and SQLite3

  - by Dunwitch

  I'm trying to get a SQLite3 DB to populate a wx.ListCrtl. I can get it to print to stdout/stderr without any problem. I just can't seem to figure out how to display the data in the DataWindow/DataList? I'm sure I've made some code mistakes, so any help is appreciated. Main.py import wx import wx.lib.mixins.listctrl as listmix from database import * import sys class DataWindow(wx.Frame): def __init__(self, parent = None): wx.Frame.__init__(self, parent, -1, 'DataList', size=(640,480)) self.win = DataList(self) self.Center() self.Show(True) class DataList(wx.ListCtrl, listmix.ListCtrlAutoWidthMixin, listmix.ColumnSorterMixin): def __init__(self, parent = DataWindow): wx.ListCtrl.__init__( self, parent, -1, style=wx.LC_REPORT|wx.LC_VIRTUAL|wx.LC_HRULES|wx.LC_VRULES) #building the columns self.InsertColumn(0, "Location") self.InsertColumn(1, "Address") self.InsertColumn(2, "Subnet") self.InsertColumn(3, "Gateway") self.SetColumnWidth(0, 100) self.SetColumnWidth(1, 150) self.SetColumnWidth(2, 150) self.SetColumnWidth(3, 150) class MainWindow(wx.Frame): def __init__(self, parent = None, id = -1, title = "MainWindow"): wx.Frame.__init__(self, parent, id, title, size = (800,600), style = wx.DEFAULT_FRAME_STYLE ^ (wx.RESIZE_BORDER)) # StatusBar self.CreateStatusBar() # Filemenu filemenu = wx.Menu() # Filemenu - About menuitem = filemenu.Append(-1, "&About", "Information about this application") self.Bind(wx.EVT_MENU, self.onAbout, menuitem) #Filemenu - Data menuitem = filemenu.Append(-1, "&Data", "Get data") self.Bind(wx.EVT_MENU, self.onData, menuitem) # Filemenu - Seperator filemenu.AppendSeparator() #Filemenu - Exit menuitem = filemenu.Append(-1, "&Exit", "Exit the application") self.Bind(wx.EVT_MENU, self.onExit, menuitem) # Menubar menubar = wx.MenuBar() menubar.Append(filemenu, "&File") self.SetMenuBar(menubar) # Show self.Show(True) self.Center() def onAbout(self, event): pass def onData(self, event): DataWindow(self) callDb = Database() sql = "SELECT rowid, address, subnet, gateway FROM pod1" records = callDb.select(sql) for v in records: print "How do I get the records on the DataList?" #print "%s%s%s" % (v[1],v[2],v[3]) #for v in records: #DataList.InsertStringItem("%s") % (v[0], v[1], v[2]) def onExit(self, event): self.Close() self.Destroy() def onSave(self, event): pass if __name__ == '__main__': app = wx.App() frame = MainWindow(None, -1) frame.Show() app.MainLoop() database.py import os import sqlite3 class Database(object): def __init__(self, db_file="data/data.sqlite"): database_allready_exists = os.path.exists(db_file) self.db = sqlite3.connect(db_file) if not database_allready_exists: self.setupDefaultData() def select(self,sql): cursor = self.db.cursor() cursor.execute(sql) records = cursor.fetchall() cursor.close return records def insert(self,sql): newID = 0 cursor = self.db.cursor() cursor.execute(sql) newID = cursor.lastrowid self.db.commit() cursor.close() return newID def save(self,sql): cursor = self.db.cursor() cursor.execute(sql) self.db.commit() cursor.close() def setupDefaultData(self): pass

  Read the article

• Refactoring an ASP.NET 2.0 app to be more "modern"

  - by Wayne M

  This is a hypothetical scenario. Let's say you've just been hired at a company with a small development team. The company uses an internal CRM/ERP type system written in .NET 2.0 to manage all of it's day to day things (let's simplify and say customer accounts and records). The app was written a couple of years ago when .NET 2.0 was just out and uses the following architectural designs: Webforms Data layer is a thin wrapper around SqlCommand that calls stored procedures Rudimentary DTO-style business objects that are populated via the sprocs A "business logic" layer that acts as a gateway between the webform and database (i.e. code behind calls that layer) Let's say that as there are more changes and requirements added to the application, you start to feel that the old architecture is showing its age, and changes are increasingly more difficult to make. How would you go about introducing refactoring steps to A) Modernize the app (i.e. proper separation of concerns) and B) Make sure that the app can readily adapt to change in the organization? IMO the changes would involve: Introduce an ORM like Linq to Sql and get rid of the sprocs for CRUD Assuming that you can't just throw out Webforms, introduce the M-V-P pattern to the forms Make sure the gateway classes conform to SRP and the other SOLID principles. Change the logic that is re-used to be web service methods instead of having to reuse code What are your thoughts? Again this is a totally hypothetical scenario that many of us have faced in the past, or may end up facing.

  Read the article

• Use `require()` with `node --eval`

  - by rentzsch

  When utilizing node.js's newish support for --eval, I get an error (ReferenceError: require is not defined) when I attempt to use require(). Here's an example of the failure: $ node --eval 'require("http");' undefined:1 ^ ReferenceError: require is not defined at eval at <anonymous> (node.js:762:36) at eval (native) at node.js:762:36 $ Here's a working example of using require() typed into the REPL: $ node > require("http"); { STATUS_CODES: { '100': 'Continue' , '101': 'Switching Protocols' , '102': 'Processing' , '200': 'OK' , '201': 'Created' , '202': 'Accepted' , '203': 'Non-Authoritative Information' , '204': 'No Content' , '205': 'Reset Content' , '206': 'Partial Content' , '207': 'Multi-Status' , '300': 'Multiple Choices' , '301': 'Moved Permanently' , '302': 'Moved Temporarily' , '303': 'See Other' , '304': 'Not Modified' , '305': 'Use Proxy' , '307': 'Temporary Redirect' , '400': 'Bad Request' , '401': 'Unauthorized' , '402': 'Payment Required' , '403': 'Forbidden' , '404': 'Not Found' , '405': 'Method Not Allowed' , '406': 'Not Acceptable' , '407': 'Proxy Authentication Required' , '408': 'Request Time-out' , '409': 'Conflict' , '410': 'Gone' , '411': 'Length Required' , '412': 'Precondition Failed' , '413': 'Request Entity Too Large' , '414': 'Request-URI Too Large' , '415': 'Unsupported Media Type' , '416': 'Requested Range Not Satisfiable' , '417': 'Expectation Failed' , '418': 'I\'m a teapot' , '422': 'Unprocessable Entity' , '423': 'Locked' , '424': 'Failed Dependency' , '425': 'Unordered Collection' , '426': 'Upgrade Required' , '500': 'Internal Server Error' , '501': 'Not Implemented' , '502': 'Bad Gateway' , '503': 'Service Unavailable' , '504': 'Gateway Time-out' , '505': 'HTTP Version not supported' , '506': 'Variant Also Negotiates' , '507': 'Insufficient Storage' , '509': 'Bandwidth Limit Exceeded' , '510': 'Not Extended' } , IncomingMessage: { [Function: IncomingMessage] super_: [Function: EventEmitter] } , OutgoingMessage: { [Function: OutgoingMessage] super_: [Function: EventEmitter] } , ServerResponse: { [Function: ServerResponse] super_: [Circular] } , ClientRequest: { [Function: ClientRequest] super_: [Circular] } , Server: { [Function: Server] super_: { [Function: Server] super_: [Function: EventEmitter] } } , createServer: [Function] , Client: { [Function: Client] super_: { [Function: Stream] super_: [Function: EventEmitter] } } , createClient: [Function] , cat: [Function] } > Is there a way to use require() with node's --eval? I'm on node 0.2.6 on Mac OS X 10.6.5.

  Read the article

• Assistance with CC Processing script

  - by JM4

  I am currently implementing a credit card processing script, most as provided by the merchant gateway. The code calls functions within a class and returns a string based on the response. The end php code I am using (details removed of course) with example information is: <?php $gw = new gwapi; $gw->setLogin("username", "password"); $gw->setBilling("John","Smith","Acme, Inc.","888","Suite 200", "Beverly Hills", "CA","77777","US","555-555-5555","555-555-5556","[email protected]", "www.example.com"); // "CA","90210","US","[email protected]"); $gw->setOrder("1234","Big Order",1, 2, "PO1234","65.192.14.10"); $r = $gw->doSale("1.00","4111111111111111","1010"); print $gw->responses['responsetext']; ?> where setlogin allows me to login, setbilling takes the sample consumer information, set order takes the order id and description, dosale takes the amount charged, cc number and exp date. when all the variables are sent validated then sent off for processing, a string is returned in the following format: response=1&responsetext=SUCCESS&authcode=123456&transactionid=23456&avsresponse=M&orderid=&type=sale&response_code=100 where: response = transaction approved or declined response text = textual response authcode = transaction authorization code transactionid = payment gateway tran id avsresponse = avs response code orderid = original order id passed in tran request response_code = numeric mapping of processor response I am trying to solve for the following: How do I take the data which is passed back and display it appropriately on the page - If the transaction failed or AVS code doesnt match my liking or something is wrong, an error is displayed to the consumer; if the transaction processed, they are taken to a completion page and the transaction id is sent in SESSION as output to the consumer If the response_code value matches a table of values, certain actions are taken, i.e. if code =100, take to success page, if code = 300 print specific error on original page to customer, etc.

  Read the article

• What is "Disable class based route addition" good for?

  - by id.roppert.dejroppert

  In the advanced TCP/IP settings of a VPN connection, i found a checkbox labeled with "Disable class based route addition". The checkbox is only enabled as long as "Use default gateway on remote network" is switched off. What is "Disable class based route addition" good for? Detailed instructions to find the settings: Open Properties of VPN connection Go to Networking tab Open Properties of "Internet Protocol Version 4 (TCP/IPv4)" (and/or TCP/IPv6) Click "Advanced..." Button Change to "IP Settings" tab Here you can find the checkboxes mentioned above

  Read the article

• Cannot determine ethernet address for proxy ARP on PPTP

  - by Linux Intel

  I installed pptp server on a centos 6 64bit server PPTP Server ip : 55.66.77.10 PPTP Local ip : 10.0.0.1 Client1 IP : 10.0.0.60 centos 5 64bit Client2 IP : 10.0.0.61 centos5 64bit PPTP Server can ping Client1 And client 1 can ping PPTP Server PPTP Server can ping Client2 And client 2 can ping PPTP Server The problem is client 1 can not ping Client 2 and i get this error also on PPTP server error log Cannot determine ethernet address for proxy ARP Ping from Client2 to Client1 PING 10.0.0.60 (10.0.0.60) 56(84) bytes of data. --- 10.0.0.60 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5000ms route -n on PPTP Server Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.60 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.0.61 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1 55.66.77.10 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 55.66.77.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 1 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 70.14.13.19 255.255.255.255 UGH 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 70.14.13.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 2 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 84.56.120.60 255.255.255.255 UGH 0 0 0 eth1 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 84.56.120.60 0.0.0.0 UG 0 0 0 eth1 cat /etc/ppp/options.pptpd on PPTP server ############################################################################### # $Id: options.pptpd,v 1.11 2005/12/29 01:21:09 quozl Exp $ # # Sample Poptop PPP options file /etc/ppp/options.pptpd # Options used by PPP when a connection arrives from a client. # This file is pointed to by /etc/pptpd.conf option keyword. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 and the kernel MPPE module. ############################################################################### # Authentication # Name of the local system for authentication purposes # (must match the second field in /etc/ppp/chap-secrets entries) name pptpd # Strip the domain prefix from the username before authentication. # (applies if you use pppd with chapms-strip-domain patch) #chapms-strip-domain # Encryption # (There have been multiple versions of PPP with encryption support, # choose with of the following sections you will use.) # BSD licensed ppp-2.4.2 upstream with MPPE only, kernel module ppp_mppe.o # {{{ refuse-pap refuse-chap refuse-mschap # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. require-mschap-v2 # Require MPPE 128-bit encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) require-mppe-128 # }}} # OpenSSL licensed ppp-2.4.1 fork with MPPE only, kernel module mppe.o # {{{ #-chap #-chapms # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. #+chapms-v2 # Require MPPE encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) #mppe-40 # enable either 40-bit or 128-bit, not both #mppe-128 #mppe-stateless # }}} # Network and Routing # If pppd is acting as a server for Microsoft Windows clients, this # option allows pppd to supply one or two DNS (Domain Name Server) # addresses to the clients. The first instance of this option # specifies the primary DNS address; the second instance (if given) # specifies the secondary DNS address. #ms-dns 10.0.0.1 #ms-dns 10.0.0.2 # If pppd is acting as a server for Microsoft Windows or "Samba" # clients, this option allows pppd to supply one or two WINS (Windows # Internet Name Services) server addresses to the clients. The first # instance of this option specifies the primary WINS address; the # second instance (if given) specifies the secondary WINS address. #ms-wins 10.0.0.3 #ms-wins 10.0.0.4 # Add an entry to this system's ARP [Address Resolution Protocol] # table with the IP address of the peer and the Ethernet address of this # system. This will have the effect of making the peer appear to other # systems to be on the local ethernet. # (you do not need this if your PPTP server is responsible for routing # packets to the clients -- James Cameron) proxyarp # Normally pptpd passes the IP address to pppd, but if pptpd has been # given the delegate option in pptpd.conf or the --delegate command line # option, then pppd will use chap-secrets or radius to allocate the # client IP address. The default local IP address used at the server # end is often the same as the address of the server. To override this, # specify the local IP address here. # (you must not use this unless you have used the delegate option) #10.8.0.100 # Logging # Enable connection debugging facilities. # (see your syslog configuration for where pppd sends to) debug # Print out all the option values which have been set. # (often requested by mailing list to verify options) #dump # Miscellaneous # Create a UUCP-style lock file for the pseudo-tty to ensure exclusive # access. lock # Disable BSD-Compress compression nobsdcomp # Disable Van Jacobson compression # (needed on some networks with Windows 9x/ME/XP clients, see posting to # poptop-server on 14th April 2005 by Pawel Pokrywka and followups, # http://marc.theaimsgroup.com/?t=111343175400006&r=1&w=2 ) novj novjccomp # turn off logging to stderr, since this may be redirected to pptpd, # which may trigger a loopback nologfd # put plugins here # (putting them higher up may cause them to sent messages to the pty) cat /etc/ppp/options.pptp on Client1 and Client2 ############################################################################### # $Id: options.pptp,v 1.3 2006/03/26 23:11:05 quozl Exp $ # # Sample PPTP PPP options file /etc/ppp/options.pptp # Options used by PPP when a connection is made by a PPTP client. # This file can be referred to by an /etc/ppp/peers file for the tunnel. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 or later from http://ppp.samba.org/ # and the kernel MPPE module available from the CVS repository also on # http://ppp.samba.org/, which is packaged for DKMS as kernel_ppp_mppe. ############################################################################### # Lock the port lock # Authentication # We don't need the tunnel server to authenticate itself noauth # We won't do PAP, EAP, CHAP, or MSCHAP, but we will accept MSCHAP-V2 # (you may need to remove these refusals if the server is not using MPPE) refuse-pap refuse-eap refuse-chap refuse-mschap # Compression # Turn off compression protocols we know won't be used nobsdcomp nodeflate # Encryption # (There have been multiple versions of PPP with encryption support, # choose which of the following sections you will use. Note that MPPE # requires the use of MSCHAP-V2 during authentication) # # Note that using PPTP with MPPE and MSCHAP-V2 should be considered # insecure: # http://marc.info/?l=pptpclient-devel&m=134372640219039&w=2 # https://github.com/moxie0/chapcrack/blob/master/README.md # http://technet.microsoft.com/en-us/security/advisory/2743314 # http://ppp.samba.org/ the PPP project version of PPP by Paul Mackarras # ppp-2.4.2 or later with MPPE only, kernel module ppp_mppe.o # If the kernel is booted in FIPS mode (fips=1), the ppp_mppe.ko module # is not allowed and PPTP-MPPE is not available. # {{{ # Require MPPE 128-bit encryption #require-mppe-128 # }}} # http://mppe-mppc.alphacron.de/ fork from PPP project by Jan Dubiec # ppp-2.4.2 or later with MPPE and MPPC, kernel module ppp_mppe_mppc.o # {{{ # Require MPPE 128-bit encryption #mppe required,stateless # }}} IPtables is stopped on clients and server, Also net.ipv4.ip_forward = 1 is enabled on PPTP Server. How can i solve this problem .?

  Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >