Search Results

Search found 32102 results on 1285 pages for 'local network'.

Page 38/1285 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• Connection to openVPN Access Server

  - by Beig

  we are using an openVPN Access Server and I would like to connect to it via the VPN network setting (network-manager-openvpn). I downloaded the client.ovpn and I can connect to the server via the command line: openvpn --script-security 2 --config client.ovpn How can I add the connection to the network manager? Which (key) entry is which? User Cert, CA Cert, Private Key? Here is an example of the client.ovpn http://nopaste.info/c10ec207f2.html Thanks in advance.

  Read the article

• NM applet dropdown options not working

  - by Prarobo

  I recently realized the dropdown options from my nm-applet are no longer working. But I can still control the network configuration by going through the dash. This happened very recently. I only realized this before a week. I guess some recent update screwed it up. I have these related packages installed network-manager-gnome 0.9.4.1-0ubuntu2 libnm-gtk0 0.9.4.1-0ubuntu2 network-manager 0.9.4.0-0ubuntu4.1 Any help would be great.

  Read the article

• how to remove obsolete device and network entries? Device manager "uninstall" option has no effect

  - by Gizmo

  I am trying to remove a few "obsolete" things which annoy me (because I like to have everything cleen, working and not interferring with each other, fresh, etc..). I tried looking for solutions without any help, so here I am to ask. My first part is about removing obsolete networks, let me explain by showing the ipconfig output: C:\windows\system32>ipconfig Windows IP Configuration Wireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter LAN: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wi-Fi: Connection-specific DNS Suffix . : home Link-local IPv6 Address . . . . . : fe80::c129:8d57:bbd1:3564%10 IPv4 Address. . . . . . . . . . . : 192.168.2.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.254 Tunnel adapter isatap.home: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : home C:\windows\system32> Specificalyy the first two adapter entries annoy me because the adapters are not visible in the network connection menu (invisible folder / file visibility set to "show"): And here is the second problem altogether with the first one: No matter what I click/do, Uninstall option has no effect on the multiplexor driver. (bridging stuff, right?) I really want to remove the Wireless LAN adapter Local Area Connection entries and the adapter multiplexor stuff but it's impossible? Why is this? How can I remove them anyway?

  Read the article

• Network Your Computers & Devices: Step by Step

  - by The Geek

  If you’re looking for a great book to help you learn more about Windows home networking, there’s a new book on the market by our good friend Ciprian, and published by none other than Microsoft Press. Note: our friend Ciprian has been a guest contributor here on How-To Geek in the past, and he’s not only a geek that knows what he’s talking about, he’s also one of the more honest and decent people I’ve worked with. In his spare time, he runs the 7 Tutorials web site. The Book One of the great things about this book is that you aren’t limited to just Windows networking—it also explains how to connect Windows 7, XP, Vista, Mac OS X, and even Linux on the same network and share folders and devices between them. Everything in the book is written in a typical How-To Geek step-by-step format, with plenty of screenshots and pictures to help you through the process. Book Outline If you’re going to be spending some money on the book, you probably want to know what it’s all about, and since the Amazon page doesn’t give, well, much information at all, here’s the entire outline for you: Setting Up a Router and Devices Setting User Account on All Computers Setting Up Your Libraries on All Windows 7 Computers Creating the Network Customizing Network Sharing Settings in Windows 7 Creating the Homegroup and Joining Windows 7 Computers Sharing Libraries and Folders Sharing and Working with Devices Streaming Media Over the Network and the Internet Sharing Between Windows XP, Windows Vista, and Windows 7 Computers Sharing Between Mac OS X and Windows 7 Computers Sharing Between Ubuntu Linux and Windows 7 Computers Keeping the Network Secure Setting Up Parental Controls Troubleshooting Network and Internet Problems It’s a great book, with loads of information, and compared to most tech books isn’t very expensive—only $19.79 for the paperback and $9.99 for the Kindle version. Well worth it, and hey, it’s an official Microsoft Press book—written by a How-To Geek guest author. Network Your Computers & Devices Step by Step [Amazon] Latest Features How-To Geek ETC How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 The 50 Best How-To Geek Windows Articles of 2010 The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC 2011 International Space Station Calendar Available for Download (Free) Ultimate Elimination – Lego Black Ops [Video] BotSync Enables Secure FTP File Synchronization on Android Devices Enjoy Beautiful City Views with the Cityscape Theme for Windows 7 Luigi Installs Any OS on Google’s Cr-48 Notebook DIY iPad Stylus Offers Pen-Based Interaction on the Cheap

  Read the article

• Oracle Social Network Developer Challenge: HarQen Nodal

  - by Kellsey Ruppel

  Originally posted by Jake Kuramoto on The Apps Lab blog. We wrapped the Oracle Social Network Developer Challenge last week at OpenWorld, and this week, I’ll be sharing all the entries. All the teams that entered our challenge did a ton of work and built really interesting integrations with Oracle Social Network, and I want to showcase their hard work and innovative ideas. Today, I give you Nodal from the HarQen (@harqen) team, Kris Gösser (@krisgosser), Jesse Vogt (@jesse_vogt) and Matt Stockton (@mstockton). The guys from HarQen built Nodal to provide a visual way to navigate your connections and conversations in Oracle Social Network and view relationships. Using Nodal, you can: Search through names and profiles in Oracle Social Network. Choose people and view their social graphs in a visually useful way. Expand nodes in the social graph and add that person’s social graph to the Nodal view for comparison. Move nodes around and lock them in place for easier viewing, using a physics engine for movement. Adjust the physics engine properties according to your viewing preferences. Select nodes in the social graph and create a conversation directly based on the selection. Here are some shots of Nodal. They really don’t do the physics engine justice, but maybe the guys at Harqen will post a video of what they did for your viewing pleasure. #gallery-1 { margin: auto; } #gallery-1 .gallery-item { float: left; margin-top: 10px; text-align: center; width: 33%; } #gallery-1 img { border: 2px solid #cfcfcf; } #gallery-1 .gallery-caption { margin-left: 0; }   Nodal’s visuals wowed the judges and the audience, and anyone with a decent-sized social network presence understands the need for good network visualization. Tools like Nodal allow you to discover hidden connections in your network and maximize the value of your weak ties and find mavens, a very important key to getting work done. Thanks to the HarQen team for participating in our challenge. We hope they had a good experience. Look for the details of the other entries this week.

  Read the article

• IPv6 local address in hosts file

  - by Dan

  I have set up a local domain on my Apache server. Then I added the following line in my /etc/hosts file ::1 exampledomain.local After I trying to navigate to it, (I tried Firefox and Chromium) I got a server not found error. Then I tried ping6 and it worked: dan@danny:~$ ping6 exampledomain.local PING exampledomain.local(exampledomain.local) 56 data bytes 64 bytes from exampledomain.local: icmp_seq=1 ttl=64 time=0.032 ms If I replace ::1 with 127.0.0.1 in my hosts file, it works fine. I'm not sure if this is relevant but this is my Virtual Host configuration in Apache2: <VirtualHost *:80> ServerAlias exampledomain.local DocumentRoot /home/dan/sites/exampledomain <Directory /home/dan/sites/exampledomain> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/exampledomain-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel debug CustomLog ${APACHE_LOG_DIR}/exampledomain-access.log combined </VirtualHost> My question is: How can I make it work with the IPv6 address?

  Read the article

• How do I.. get a value for time at 9:00am local, regardless of the timezone?

  - by ander163

  In my app, I need to set a variable for a start time to be 9:00 a.m. local, wherever the user is located. I have a timezone variable for each user and the save and retrieve are all working. But I need to set a variable when I create a new event to be 9:00 am in the user's local time zone. My current method uses the local time of the server, then makes the adjustments for the individual user's time zone. I don't know what I don't know - is there a command to create the value for "Today's date at 9:00 am where you are"? My current code is: t = Time.now.to_date.beginning_of_day + 11.hours (forcing the 2 hour offset between my primary user and the server in a different timezone).

  Read the article

• What are some topics you'd like to see covered in an 'Introduction to Network Security' book?

  - by seth.vargo

  I'm trying to put together a list of topics in Network Security and prioritize them accordingly. A little background on the book - we are trying to gear the text towards college students, as an introduction to security, and toward IT professionals who have recently been tasked with securing a network. The idea is to create a book that covers the most vital and important parts of securing a network with no assumptions. So, if you were a novice student interested in network security OR an IT professional who needed a crash course on network security, what topics do you feel would be of the upmost importance in such a text?

  Read the article

• Embedded C++, any tips to avoid a local thats only used to return a value on the stack?

  - by lisarc

  I have a local that's only used for the purposes of checking the result from another function and passing it on if it meets certain criteria. Most of the time, that criteria will never be met. Is there any way I can avoid this "extra" local? I only have about 1MB of storage for my binary, and I have several thousand function calls that follow this pattern. I know it's a minor thing, but if there's a better pattern I'd love to know! SomeDataType myclass::myFunction() { SomeDataType result; // do I really need this local??? // i need to check the result and pass it on if it meets a certain condition result = doSomething(); if ( ! result ) { return result; } // do other things here ... // normal result of processing return SomeDataType(whatever); }

  Read the article

• Securely sending data from shared hosted PHP script to local MSSQL

  - by user329488

  I'm trying to add data from a webhook (from a web cart) to a local Microsoft SQL Server. It seems like the best route for me is to use a PHP script to listen for new data (POST as json), parse it, then query to add to MSSQL. I'm not familiar with security concerning the connection between the PHP script (which would sit on a shared-host website) and the local MSSQL database. I would just keep the PHP script running on the same localhost (have Apache running on Windows), but the URI for the webhook needs to be publicly accessible. Alternately, I assume that I could just schedule a script from the localhost to check periodically for updates through the web carts API, though the webhooks seem to be more fool-proof for an amateur programmer like myself. What steps can I take to ensure security when using a PHP on a remote, shared-host to connect to MSSQL on my local machine?

  Read the article

• Local Entities with NHibernate

  - by Ricardo Peres

  You may know that Entity Framework Code First has a nice property called Local which lets you iterate through all the entities loaded by the current context (first level cache). This comes handy at times, so I decided to check if it would be difficult to have it on NHibernate. It turned out it is not, so here it is! Another nice addition to an NHibernate toolbox! public static class SessionExtensions { public static IEnumerable<T> Local<T>(this ISession session) { ISessionImplementor impl = session.GetSessionImplementation(); IPersistenceContext pc = impl.PersistenceContext; foreach (Object key in pc.EntityEntries.Keys) { if (key is T) { yield return ((T) key); } } } } //simple usage IEnumerable<Post> localPosts = session.Local<Post>(); SyntaxHighlighter.config.clipboardSwf = 'http://alexgorbatchev.com/pub/sh/2.0.320/scripts/clipboard.swf'; SyntaxHighlighter.brushes.CSharp.aliases = ['c#', 'c-sharp', 'csharp']; SyntaxHighlighter.all();

  Read the article

• Juju bootstrap fails to start network on local environment

  - by Amith KK

  I've followed the instructions at https://juju.ubuntu.com/CharmSchool and rebooted 5 times...... I cant seem to do a juju-bootstrap (local) This is the output: amith@amith-desktop:~$ juju bootstrap 2011-11-24 17:08:05,708 INFO Bootstrapping environment 'local' (type: local)... 2011-11-24 17:08:05,710 INFO Checking for required packages... 2011-11-24 17:08:06,593 INFO Starting networking... error: Failed to start network default error: internal error Child process (dnsmasq --strict-order --bind-interfaces --pid-file=/var/run/libvirt/network/default.pid --conf-file= --except-interface lo --listen-address 192.168.122.1 --dhcp-range 192.168.122.2,192.168.122.254 --dhcp-leasefile=/var/lib/libvirt/dnsmasq/default.leases --dhcp-lease-max=253 --dhcp-no-override) status unexpected: exit status 2 Command '['virsh', 'net-start', 'default']' returned non-zero exit status 1 2011-11-24 17:08:07,217 ERROR Command '['virsh', 'net-start', 'default']' returned non-zero exit status 1 Is there any fix at all?

  Read the article

• Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect

  - by user287529

  Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect. I'm using Ubuntu 12.04 on an Acer Aspire 5742-7645 laptop with 4GB memory, Intel Core i3 processor, Intel HD Graphics, DVD drive, 802.1 b/g/n, and 500 GB HD. I connect to my router via a wireless connection. I have installed Virutalbox 4.1.12 from the Ubuntu Software Center and installed Guest additions 4.1.12 in the Windows 7 guest session. I have Windows XP and Windows 7 installed as guests in Virtual box The network settings are different for XP and 7 – see below. Network Settings XP guest = Adapter 1: PCnet-FAST III (NAT) - Network works perfectly and has worked well for several years. Network Settings Win 7 = Adapter 1: Intel PRO/1000 MT Desktop (Bridged adapter, eth1) Promiscuous Mode = allow all Cable connected = checked When I originally installed Windows 7, I tried NAT and the guest network would not connect. Once I changed the setting to the above (Bridged) the Network worked perfectly. However, what I believe is after updates (not sure if it was an Ubuntu or Windows update) the guest network stopped working and I can not get it to connect. Interfaces file content auto lo iface lo inet loopback Ifconfig yields lou@lou-Aspire-5742:~$ ifconfig eth0 Link encap:Ethernet HWaddr 1c:75:08:09:f6:5c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 Link encap:Ethernet HWaddr 4c:0f:6e:7c:9f:01 inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4e0f:6eff:fe7c:9f01/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18095 errors:2 dropped:0 overruns:0 frame:24344 TX packets:9281 errors:47 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5301926 (5.3 MB) TX bytes:1441885 (1.4 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3208 errors:0 dropped:0 overruns:0 frame:0 TX packets:3208 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:294088 (294.0 KB) TX bytes:294088 (294.0 KB) Ipconfig yields the following: Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::38ba:dbca:a21d:c3d1%13 Autoconfiguration IPv4 Address. . : 169.254.195.209 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{B292E440-679D-4FC5-8E34-77D6804669C8}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : I'm not sure what else to do. Can someone provide the troubleshooting steps to determine what the problem is and possible solution?

  Read the article

• Network communication across two private network

  - by Sethu

  Hi All, I am trying to implement a peer to peer communication .. I use sockets for communication between them. I want to know if there are any ways i can use the same sort of communication when the two peers are behind two private Networks (They dont know each others public ip address.) I can think of a shared buffer in a well known location as a means of communication. But is there some other way to get this done?

  Read the article

• my windows xp sp3 diagnostick:windows could not detect any wired or wireless network cards installed on your machine

  - by Yosef

  Problem: cant connect to internet with my new installation of windows xp sp3. Details: I have ubuntu in pc that worked with wired internet. i format all disk and install windows xp sp3. i have auto internet that defined in my router - other computers have internet. I run diagnoze of ie and get: windows could not detect any wired or wireless network cards installed on your machine In Device Manager i have only 1394 Adapter I dont see any internet adapters. Edit: I find with ubuntu livecd that i have hardware:82566dc gigabit network connection Thanks

  Read the article

• "no such file to load -- treetop/runtime" running "rake jobs:work"

  - by Ryan Marshall

  when i try and run the "rails server" or "rake jobs:work" i get the error: "no such file to load -- treetop/runtime" full trace: macbook-pro-2:domain ryan$ rake jobs:work --trace(in /Applications/htdocs/domain) rake aborted! no such file to load -- treetop/runtime /opt/local/lib/ruby/gems/1.8/gems/mail-2.2.14/lib/mail.rb:68:in require' /opt/local/lib/ruby/gems/1.8/gems/mail-2.2.14/lib/mail.rb:68 /opt/local/lib/ruby/gems/1.8/gems/mail-2.2.14/lib/mail.rb:61:ineach' /opt/local/lib/ruby/gems/1.8/gems/mail-2.2.14/lib/mail.rb:61 /opt/local/lib/ruby/gems/1.8/gems/delayed_job-2.1.2/lib/delayed/performable_mailer.rb:1:in require' /opt/local/lib/ruby/gems/1.8/gems/delayed_job-2.1.2/lib/delayed/performable_mailer.rb:1 /opt/local/lib/ruby/gems/1.8/gems/delayed_job-2.1.2/lib/delayed_job.rb:5:inrequire' /opt/local/lib/ruby/gems/1.8/gems/delayed_job-2.1.2/lib/delayed_job.rb:5 /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler/runtime.rb:64:in require' /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler/runtime.rb:64:inrequire' /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler/runtime.rb:62:in each' /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler/runtime.rb:62:inrequire' /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler/runtime.rb:51:in each' /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler/runtime.rb:51:inrequire' /opt/local/lib/ruby/gems/1.8/gems/bundler-1.0.7/lib/bundler.rb:112:in require' /ApApplications/htdocs/domain/config/application.rb:7 /opt/local/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:ingem_original_require' /opt/local/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in require' /Applications/htdocs/domain/Rakefile:4 /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2383:inload' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2383:in raw_load_rakefile' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2017:inload_rakefile' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in standard_exception_handling' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2016:inload_rakefile' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2000:in run' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:instandard_exception_handling' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1998:in run' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake:31 /opt/local/bin/rake:19:inload' /opt/local/bin/rake:19 in my Gemfile i have: "gem 'delayed_job'"

  Read the article

• Connecting a network drive only when the VPN is connected?

  - by leeand00

  I have a thumb drive that I want to be able to connect to the same place over the network at one location as it is locally. Sometimes I leave it at the other location, but usually if I'm going to back it up, I back it up locally for network traffic. Is there a way to automatically connect the thumb drive when I connect to the VPN? (Always to the same drive letter...and obviously skip connecting it if it's already plugged in locally and the VPN is connected...) I'm using a Cisco VPN Client 5.x

  Read the article

• How do you confirm network adapter is gigabit capable?

  - by StrandedPirate

  Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

  Read the article

• Under which circumstances can a *local* user account access a remote SQL Server with a trusted connection?

  - by Heinzi

  One of our customers has the following configuration: On the domain controller, there's an SQL Server. On his PC (WinXP), he logs on with LocalPC\LocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It works. In SSMS, the connection shows up with the user Domain\Administrator. Firstly, I was surprised that this even works. (My first suspicion was that there is a user with the same name and password in the domain, but there is no user LocalUser in the domain.) Then we tried to reproduce the same behaviour on his new PC, but failed: On his new PC (Win7), he logs on with OtherLocalPC\OtherLocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It fails with the error message Login failed for user ''. The user is not associated with a trusted SQL Server connection. Hence my question: Under which conditions can a non-domain user access a remote SQL Server using Windows Authentication with different credentials? Apparently, it's possible (it works on his old PC), but why? And how can I reproduce it?

  Read the article

• How to find specific/local files via CMake

  - by Andreas Romeyke

  Hello, I have a problem with a locally installed library. In my project there is the xmlrpc++0.7-library: myproject/ +-- xmlrpc++0.7/ +-- src/ I want that CMake fallbacks using the local xmlrpc++0.7 directory if not found otherwise. Two problems, the first one, find_path() or find_library() does not work with local dir. I used a workaround testing if variables processed by find_xxx() are empty or not. If empty I set them manually. The cmake generates the Makefile without errors now. But if I want to compile the project via make, the c++ compiler returns "error: XmlRpc.h: file not found". The file XmlRpc.h lies in myproject/xmlrpc++0.7/src and if I compile all them manually it works fine. Here is my CMakeLists.txt. I am very happy if anyone could me point to the right solution to use cmake under conditions described above. --- CMakeLists.txt --- project(webservice_tesseract) cmake_minimum_required(VERSION 2.6) set(CMAKE_INCLUDE_CURRENT_DIR ON) # find tesseract find_path(TESSERACT_INCLUDE_DIR tesseract/tesseractmain.h /opt/local/include /usr/local/include /usr/include ) find_library(TESSERACT_LIBRARY_DIR NAMES tesseract_main PATHS /opt/local/lib/ /usr/local/lib/ /usr/lib ) message(STATUS "looked for tesseract library.") message(STATUS "Include file detected: [${TESSERACT_INCLUDE_DIR}].") message(STATUS "Lib file detected: [${TESSERACT_LIBRARY_DIR}].") add_library(tesseract STATIC IMPORTED) set_property(TARGET tesseract PROPERTY IMPORTED_LOCATION ${TESSERACT_LIBRARY_DIR}/libtesseractmain.a ) #find xmlrpc++ message(STATUS "cmake home dir: [${CMAKE_HOME_DIRECTORY}].") set(LOCAL_XMLRPCPLUSPLUS ${CMAKE_HOME_DIRECTORY}/xmlrpc0.7++/) message(STATUS "xmlrpc++ local dir: [${LOCAL_XMLRPCPLUSPLUS}].") find_path(XMLRPCPLUSPLUS_INCLUDE_DIR XmlRpcServer.h ${LOCAL_XMLRPCPLUSPLUS}src /opt/local/include /usr/local/include /usr/include ) find_library(XMLRPCPLUSPLUS_LIBRARY_DIR NAMES XmlRpc PATHS ${LOCAL_XMLRPCPLUSPLUS} /opt/local/lib/ /usr/local/lib/ /usr/lib/ ) # next lines are an ugly workaround because cmake find_xxx() does not find local stuff if (XMLRPCPLUSPLUS_INCLUDE_DIR) else (XMLRPCPLUSPLUS_INCLUDE_DIR) set(XMLRPCPLUSPLUS_INCLUDE_DIR ${LOCAL_XMLRPCPLUSPLUS}src) endif (XMLRPCPLUSPLUS_INCLUDE_DIR) if (XMLRPCPLUSPLUS_LIBRARY_DIR) else (XMLRPCPLUSPLUS_LIBRARY_DIR) set(XMLRPCPLUSPLUS_LIBRARY_DIR ${LOCAL_XMLRPCPLUSPLUS}) endif (XMLRPCPLUSPLUS_LIBRARY_DIR) message(STATUS "looked for xmlrpc++ library.") message(STATUS "Include file detected: [${XMLRPCPLUSPLUS_INCLUDE_DIR}].") message(STATUS "Lib file detected: [${XMLRPCPLUSPLUS_LIBRARY_DIR}].") add_library(xmlrpc STATIC IMPORTED) set_property(TARGET xmlrpc PROPERTY IMPORTED_LOCATION ${XMLRPCPLUSPLUS_LIBRARY_DIR}/libXmlRpc.a ) #### link together include_directories(${XMLRPCPLUSPLUS_INCLUDE_DIR} ${TESSERACT_INCLUDE_DIR}) link_directories(${XMLRPCPLUSPLUS_LIBRARY_DIR} ${TESSERACT_LIBRARY_DIR}) add_library(simpleocr STATIC simple_ocr.cpp) add_executable(webservice_tesseract webservice.cpp) target_link_libraries(webservice_tesseract xmlrpc tesseract simpleocr)

  Read the article

• Network printer - Print direct or via shared printer on Server?

  - by NickC

  It has occurred to me that a workstation can connect to a printer in two ways: 1). Printing directly to the IP of the printer with the print driver installed locally. 2). Printing to a \Server\Printer1 share with the print queue residing on the server. Question is which way is preferred? I would assume that printing directly to a network printer rather than going through the server would be the most efficient from the point of view of network traffic. On the other hand I guess a server printer share would be easier to manage with the correct driver automatically being downloaded to the workstations. Also what about using GPP (Server2012) to install this printer on the workstations, does that require any specific way?

  Read the article

• Installing linux on a crippled machine via network boot?

  - by networkbooter

  I have a somewhat ancient Toshiba laptop (which can't boot from USB) that I want to install linux on (probably Ubuntu). I'm currently running Windows XP and Ubuntu via Wubi. I want to delete these OSs and replace with Ubuntu only. The laptop does have a network boot option. I'm wondering if the easiest way might be to setup a network boot server on my other computer (which runs Ubunutu) and boot the laptop from it. Could this allow me to install Linux on the laptop? I can't seem to find instructions on the 'net as to how to go about doing this.

  Read the article

• When an Excel file is locked on a network share, how does it know who locked the file?

  - by ScottStonehouse

  We are using Excel 2010 and sometimes users are working from a network share. When a user on the network opens the file in Excel, the file is locked for editing - this is the expected behavior. When another user tries to open the file, Excel gives the message [filename] is locked for editing by 'John Doe' The problem is, the user is always this one particular user's name, no matter who actually has the file open. Where does Excel get this info, and how do I fix it? Update: I should have mentioned that in Excel, under Options (General), the correct user names have been set up. That is not where this user name is coming from.

  Read the article

• ASA5505 Novice. Setting up Outside/Inside/and DMZ as Guest Network

  - by GriffJ

  I need a little help in developing a config for our ASA5505. I'm an MCSA/MCITPAS but I don't have a lot of practical cisco experience. Here is what I need help with, we currently have a PIX as our boarder gateway and well it's antiquated and it only has a 50 user license which means I'm constantly clearing local-host throughout the day as people complain. I discovered that the last IT person bought at couple ASA5505s and they've been sitting in the back of a cupboard. So far I've duplicated the configuration from the pix to the asa but as I was going to be going this far I thought I'd go further and remove another old cisco router that was used only for the guest network, I know the asa can do both jobs. So I'm going to paste a scenario I wrote up with the actual IPs changed to protect the innocent. ... Outside Network: 1.2.3.10 255.255.255.248 (we have a /29) Inside Network: 10.10.36.0 255.255.252.0 DMZ Network: 192.168.15.0 255.255.255.0 Outside Network on e0/0 DMZ Network on e0/1 Inside Network on e0/2-7 DMZ Network has DHCPD Enabled. DMZ DHCPD Pool is 192.168.15.50-192.168.15.250 DMZ Network needs to be able to see DNS on Inside Network at 10.10.37.11 and 10.10.37.12 DMZ Network needs to be able to access webmail on inside network at 10.10.37.15 DMZ Network needs to be able to access business website on inside network at 10.10.37.17 DMZ Network needs to be able to access the outside network (access to the internet). Inside Network has NO DHCPD. (dhcp is handled by domain controller) Inside Network needs to be able to see anything on the DMZ network. Inside Network needs to be able to access the outside network (access to the internet). There is some access-list stuff already, some static mapping already. Maps external IPs from our ISP to our inside server IPs static (inside,outside) 1.2.3.11 10.10.37.15 netmask 255.255.255.255 static (inside,outside) 1.2.3.12 10.10.37.17 netmask 255.255.255.255 static (inside,outside) 1.2.3.13 10.10.37.20 netmask 255.255.255.255 Allows access to our Webserver/Mailserver/VPN from the Outside. access-list 108 permit tcp any host 1.2.3.11 eq https access-list 108 permit tcp any host 1.2.3.11 eq smtp access-list 108 permit tcp any host 1.2.3.11 eq 993 access-list 108 permit tcp any host 1.2.3.11 eq 465 access-list 108 permit tcp any host 1.2.3.12 eq www access-list 108 permit tcp any host 1.2.3.12 eq https access-list 108 permit tcp any host 1.2.3.13 eq pptp Here is all the NAT and route stuff I have so far. global (outside) 1 interface global (outside) 2 1.2.3.11-1.2.3.14 netmask 255.255.255.248 nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 1.2.3.9 1

  Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >