Search Results

Search found 1565 results on 63 pages for 'bus'.

Page 39/63 | < Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >

• Ubuntu 12.04 + Wifi not working

  - by user171154

  i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

  Read the article

• Wireless networks are not detected at start up in Ubuntu 12.04

  - by Kanhaiya Mishra

  I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

  Read the article

• Testing Workflows &ndash; Test-First

  - by Timothy Klenke

  Originally posted on: http://geekswithblogs.net/TimothyK/archive/2014/05/30/testing-workflows-ndash-test-first.aspxThis is the second of two posts on some common strategies for approaching the job of writing tests.  The previous post covered test-after workflows where as this will focus on test-first.  Each workflow presented is a method of attack for adding tests to a project.  The more tools in your tool belt the better.  So here is a partial list of some test-first methodologies. Ping Pong Ping Pong is a methodology commonly used in pair programing.  One developer will write a new failing test.  Then they hand the keyboard to their partner.  The partner writes the production code to get the test passing.  The partner then writes the next test before passing the keyboard back to the original developer. The reasoning behind this testing methodology is to facilitate pair programming.  That is to say that this testing methodology shares all the benefits of pair programming, including ensuring multiple team members are familiar with the code base (i.e. low bus number). Test Blazer Test Blazing, in some respects, is also a pairing strategy.  The developers don’t work side by side on the same task at the same time.  Instead one developer is dedicated to writing tests at their own desk.  They write failing test after failing test, never touching the production code.  With these tests they are defining the specification for the system.  The developer most familiar with the specifications would be assigned this task. The next day or later in the same day another developer fetches the latest test suite.  Their job is to write the production code to get those tests passing.  Once all the tests pass they fetch from source control the latest version of the test project to get the newer tests. This methodology has some of the benefits of pair programming, namely lowering the bus number.  This can be good way adding an extra developer to a project without slowing it down too much.  The production coder isn’t slowed down writing tests.  The tests are in another project from the production code, so there shouldn’t be any merge conflicts despite two developers working on the same solution. This methodology is also a good test for the tests.  Can another developer figure out what system should do just by reading the tests?  This question will be answered as the production coder works there way through the test blazer’s tests. Test Driven Development (TDD) TDD is a highly disciplined practice that calls for a new test and an new production code to be written every few minutes.  There are strict rules for when you should be writing test or production code.  You start by writing a failing (red) test, then write the simplest production code possible to get the code working (green), then you clean up the code (refactor).  This is known as the red-green-refactor cycle. The goal of TDD isn’t the creation of a suite of tests, however that is an advantageous side effect.  The real goal of TDD is to follow a practice that yields a better design.  The practice is meant to push the design toward small, decoupled, modularized components.  This is generally considered a better design that large, highly coupled ball of mud. TDD accomplishes this through the refactoring cycle.  Refactoring is only possible to do safely when tests are in place.  In order to use TDD developers must be trained in how to look for and repair code smells in the system.  Through repairing these sections of smelly code (i.e. a refactoring) the design of the system emerges. For further information on TDD, I highly recommend the series “Is TDD Dead?”.  It discusses its pros and cons and when it is best used. Acceptance Test Driven Development (ATDD) Whereas TDD focuses on small unit tests that concentrate on a small piece of the system, Acceptance Tests focuses on the larger integrated environment.  Acceptance Tests usually correspond to user stories, which come directly from the customer. The unit tests focus on the inputs and outputs of smaller parts of the system, which are too low level to be of interest to the customer. ATDD generally uses the same tools as TDD.  However, ATDD uses fewer mocks and test doubles than TDD. ATDD often complements TDD; they aren’t competing methods.  A full test suite will usually consist of a large number of unit (created via TDD) tests and a smaller number of acceptance tests. Behaviour Driven Development (BDD) BDD is more about audience than workflow.  BDD pushes the testing realm out towards the client.  Developers, managers and the client all work together to define the tests. Typically different tooling is used for BDD than acceptance and unit testing.  This is done because the audience is not just developers.  Tools using the Gherkin family of languages allow for test scenarios to be described in an English format.  Other tools such as MSpec or FitNesse also strive for highly readable behaviour driven test suites. Because these tests are public facing (viewable by people outside the development team), the terminology usually changes.  You can’t get away with the same technobabble you can with unit tests written in a programming language that only developers understand.  For starters, they usually aren’t called tests.  Usually they’re called “examples”, “behaviours”, “scenarios”, or “specifications”. This may seem like a very subtle difference, but I’ve seen this small terminology change have a huge impact on the acceptance of the process.  Many people have a bias that testing is something that comes at the end of a project.  When you say we need to define the tests at the start of the project many people will immediately give that a lower priority on the project schedule.  But if you say we need to define the specification or behaviour of the system before we can start, you’ll get more cooperation.   Keep these test-first and test-after workflows in your tool belt.  With them you’ll be able to find new opportunities to apply them.

  Read the article

• Problem to display 3D google map.

  - by nemade-vipin

  hello friends, I have implemented one Flex application in which I want to display 3D google map.In which I am getting the error the NUll object reference during map display. Here is my code:- import com.google.maps.controls.MapTypeControl; import adobe.utils.XMLUI; import mx.rpc.events.FaultEvent; import mx.controls.Alert; import generated.webservices.*; import mx.collections.ArrayCollection; import mx.controls.*; import generated.webservices.*; import com.google.maps.LatLng; import com.google.maps.Map3D; import com.google.maps.MapEvent; import com.google.maps.MapMouseEvent; import com.google.maps.services.GeocodingEvent; import com.google.maps.services.ClientGeocoder; import com.google.maps.overlays.Marker; import com.google.maps.InfoWindowOptions; import com.google.maps.MapOptions; import com.google.maps.MapType; import com.google.maps.View; import com.google.maps.controls.NavigationControl; import com.google.maps.geom.Attitude; import mx.controls.Alert; [Bindable] private var childName:ArrayCollection; [Bindable] private var childId:ArrayCollection; private var photoFeed:ArrayCollection; private var trackinginfochild:TrackingInfo; private var arrayOfchild:Array; private var newEntry:GetSBTSMobileAuthentication; private var trackinginfo:GetSBTSTrackingInfo; private var childObj:Child; private var UserId:int; private var lat:int; private var long:int; private var latlong:LatLng; public var user:SBTSWebService; public function authentication():void { // Instantiate a new Entry object. user = new SBTSWebService(); if(user!=null) { user.addSBTSWebServiceFaultEventListener(handleFaults); user.addgetSBTSMobileAuthenticationEventListener(authenticationResult); newEntry = new GetSBTSMobileAuthentication(); if(newEntry!=null) { newEntry.mobile=mobileno.text; newEntry.password=password.text; user.getSBTSMobileAuthentication(newEntry); } } } public function handleFaults(event:FaultEvent):void { Alert.show("A fault occured contacting the server. Fault message is: " + event.fault.faultString); } public function authenticationResult(event:GetSBTSMobileAuthenticationResultEvent):void { if(event.result != null && event.result._return>0) { if(event.result._return > 0) { UserId = event.result._return; loginform.enabled = false; getChildList(UserId); viewstack2.selectedIndex=1; } else { Alert.show("Authentication fail"); } } } public function getChildList(userId:int):void { var childEntry:GetSBTSMobileChildrenInfo = new GetSBTSMobileChildrenInfo(); childEntry.UserId = userId; user.addgetSBTSMobileChildrenInfoEventListener(sbtsChildrenInfoResult); user.getSBTSMobileChildrenInfo(childEntry); } public function sbtsChildrenInfoResult(event:GetSBTSMobileChildrenInfoResultEvent):void { if( event.result._return!=null) { arrayOfchild = event.result._return as Array; photoFeed = new ArrayCollection(arrayOfchild); childName = new ArrayCollection(); for( var count:int=0;count<photoFeed.length;count++) { childObj = photoFeed.getItemAt(count,0) as Child; childName.addItem(childObj.strName); } } } private function trackingInfo():void { for( var count:int=0;count user.getSBTSTrackingInfo(trackinginfo); } } } } private function getTrackingInfo(event:GetSBTSTrackingInfoResultEvent):void { if(event.result._return != null) { trackinginfochild = event.result._return as TrackingInfo; lat = trackinginfochild.dblLatitude; long = trackinginfochild.dblLongitude; latlong = new LatLng(lat,long); } } private function onMapPreinitialize(event:MapEvent):void { var myMapOptions:MapOptions = new MapOptions(); myMapOptions.zoom = 12; myMapOptions.center = latlong; myMapOptions.mapType = MapType.NORMAL_MAP_TYPE; myMapOptions.viewMode = View.VIEWMODE_PERSPECTIVE; myMapOptions.attitude = new Attitude(20,30,0); buslocation.setInitOptions(myMapOptions); buspath.setInitOptions(myMapOptions); } private function onMapReady(event:MapEvent):void { this.buslocation.addControl(new NavigationControl()); this.buslocation.addControl( new MapTypeControl()); } ]]> <mx:Move id="hideEffect" yTo="-500" /> <mx:Move id="showEffect" xFrom="500"/> <mx:Panel width="100%" height="100%" headerColors="[#000000,#FFFFFF]" hideEffect="{hideEffect}" showEffect="{showEffect}"> <mx:TabNavigator id="viewstack2" selectedIndex="0" creationPolicy="all" width="100%" height="100%"> <mx:Form label="Login Form" id="loginform" hideEffect="{hideEffect}" showEffect="{showEffect}"> <mx:FormItem label="Mobile NO:" creationPolicy="all"> <mx:TextInput id="mobileno"/> </mx:FormItem> <mx:FormItem label="Password:" creationPolicy="all"> <mx:TextInput displayAsPassword="true" id="password" /> </mx:FormItem> <mx:FormItem> <mx:Button label="Login" click="authentication()"/> </mx:FormItem> </mx:Form> <mx:Form label="Child List" id="childForm" hideEffect="{hideEffect}" showEffect="{showEffect}"> <mx:Label width="100%" color="blue" text="Select Child."/> <mx:RadioButtonGroup id="radioGroup" itemClick="trackingInfo()"/> <mx:Repeater id="fieldRepeater" dataProvider="{childName}"> <mx:RadioButton groupName="radioGroup" label="{fieldRepeater.currentItem}" value="{fieldRepeater.currentItem}"/> </mx:Repeater> </mx:Form> <mx:Form label="Child Information" hideEffect="{hideEffect}" showEffect="{showEffect}"> <mx:FormItem> <mx:DataGrid id="childinfo"> <mx:columns> <mx:DataGridColumn headerText="Child Name" dataField="strName"/> <mx:DataGridColumn headerText="School Name" dataField="strSchoolName"/> <mx:DataGridColumn headerText="Pick Up Point" dataField="strPickUpPointName"/> <mx:DataGridColumn headerText="Drop Down Point" dataField="strDropDownPointName"/> </mx:columns> </mx:DataGrid> </mx:FormItem> <mx:FormItem> <mx:Button label="click here to see bus location"/> </mx:FormItem> </mx:Form> <mx:Form label="Bus Location" hideEffect="{hideEffect}" showEffect="{showEffect}"> <maps:Map3D xmlns:maps="com.google.maps.*" mapevent_mappreinitialize="onMapPreinitialize(event)" id="buslocation" width="100%" height="100%" url="http://code.google.com/apis/maps/" key="ABQIAAAAXuX6aG-r_N0-tQNxUEV-vRSE8al1BQssMxLXJiP75kIjR3ssLxT3D52_u94hI-dMIkD72FmnK-P4og"/> </mx:Form> <mx:Form label="Bus path" hideEffect="{hideEffect}" showEffect="{showEffect}"> <maps:Map3D xmlns:maps="com.google.maps.*" mapevent_mappreinitialize="onMapPreinitialize(event)" id="buspath" width="100%" height="100%" url="http://code.google.com/apis/maps/" key="ABQIAAAAXuX6aG-r_N0-tQNxUEV-vRSE8al1BQssMxLXJiP75kIjR3ssLxT3D52_u94hI-dMIkD72FmnK-P4og"/> </mx:Form> </mx:TabNavigator> </mx:Panel> I am getting this error :- TypeError: Error #1009: Cannot access a property or method of a null object reference. at com.google.maps.geom::Geometry$/computeSeparatingAxes() at com.google.maps.geom::TileEnumerator/enumerateTiles() at com.google.maps.core::PerspectiveTilePane/computeOptimalSet() at com.google.maps.core::PerspectiveTilePane/render() at com.google.maps.core::PerspectiveTilePane/configure() at com.google.maps.managers::PerspectiveTileManager/updateView() at com.google.maps.managers::PerspectiveTileManager/initializePanes() at com.google.maps.managers::PerspectiveTileManager/onInitialize() at MethodInfo-190() at flash.events::EventDispatcher/dispatchEventFunction() at flash.events::EventDispatcher/dispatchEvent() at mx.core::UIComponent/dispatchEvent()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:9298] at com.google.maps.wrappers::BaseEventDispatcher/dispatchEvent() at com.google.maps.wrappers::EventDispatcherWrapper/dispatchEvent() at com.google.maps.core::MapImpl/size() at com.google.maps.core::MapImpl/setSize() at com.google.maps.wrappers::IMapWrapper/setSize() at com.google.maps::Map/internalSetSize() at com.google.maps::Map/onUIComponentResized() at flash.events::EventDispatcher/dispatchEventFunction() at flash.events::EventDispatcher/dispatchEvent() at mx.core::UIComponent/dispatchEvent()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:9298] at mx.core::UIComponent/dispatchResizeEvent()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:7077] at mx.core::UIComponent/setActualSize()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:6706] at mx.containers.utilityClasses::BoxLayout/updateDisplayList()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\containers\utilityClasses\BoxLayout.as:219] at mx.containers::Form/updateDisplayList()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\containers\Form.as:375] at mx.core::UIComponent/validateDisplayList()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:6351] at mx.core::Container/validateDisplayList()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\Container.as:2677] at mx.managers::LayoutManager/validateDisplayList()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\managers\LayoutManager.as:622] at mx.managers::LayoutManager/doPhasedInstantiation()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\managers\LayoutManager.as:695] at Function/http://adobe.com/AS3/2006/builtin::apply() at mx.core::UIComponent/callLaterDispatcher2()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:8628] at mx.core::UIComponent/callLaterDispatcher()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as:8568] Please resolve my issue.

  Read the article

• DIY a simple .inf on an existing .sys?

  - by Stijn Sanders

  In continuation of attempting to get an old Digi ST-1032 working on a new server, we've downgraded a server to Windows 2000 in an attempt to use the NT4 drivers. And it works, the old software setup works, finds the device on the SCSI bus, and connects the 32 ports to COM3..COM34 or any other set using the port remapper tool. The minor issue that remains is that Plug-and-Play still detects this device over SCSI and tries to wizard you into selecting a driver for it. Which doesn't exists (Digi Intl support confirms this device is so old, a 2000 or XP driver was never made). The exact name displayed is "DigiIntl ST-1032 SCSI Net Device" (Oddly enough, two devices get detected with this name, on two neighbouring LUN's, could one be the built-in terminator?) Is there a way to concoct a simple .inf that would (re-)register the existing sts.sys that appears to get registered by the (old) installer of the driver software?

  Read the article

• 8Gb Fiber Channcel HBA vs. 10 Gb SPF+ Converged HBA

  - by Hossein Aarabi

  I am putting a Dell server together, more specifically R720. I have to select the correct Host Bus Adapter. This HBA on R710 will connect to a storage device. I am confused between these two: QLogic 2562, Dual Port 8Gb Optical Fiber Channel HBA (price $2,045) QLogic 8262, Dual Port 10Gb SFP+, Converged Network Adapter (price $1,618) I thought since the QLogic 2562 is a fiber channel and is more expensive then it is faster in terms of IOPS. But, it is a 8Gb as opposed to 10 Gb of SFP+. My questions: Which one is better (IOPS performance, etc.)? Why should I choose one over another?

  Read the article

• Which CPU for SQL Server machine (Xeon, i5, i7, AMD Phenom)?

  - by Tony_Henrich

  I am going to build a full height server machine to be used for SQL Server 2008 64bit. I have $400 to spend for a CPU. Which CPU should I get among i5, i7, Xeon and Phenom in terms of performance. There are so many options and I am out of touch with the latest stuff. All I know I want something fast and works with DDR3 fast memory and works with some kind of fast system bus. I don't care about overclocking, 3D & gfx benchmarks. The machine is not used for games and gfx apps. Any recommendations?

  Read the article

• Intel P6100 CPU and Mobile Intel® HM55 Express Chipset

  - by Christopher Painter

  I have an Asus K52F-BBR5 notebook that uses an Intel P6100 ( 2GHZ 15x multiplier) and HM55 Express Chipset. I'm looking to replace it's 3GB with 8GB. The Crucial database seems to indicate that a PC3-8500 CAS 7 and PC3-10666 CAS 9 will both work. I'm not up to date on the latest DDR3 nomencalature and I'm wondering which would provide better performance. The price difference is negligible. Drawing on past experiences from many many years ago I could make an argument for either based on sync/async bus speed arguments and CAS latency differences but the truth is I don't know enough about the HM55 chipset to know which would be the correct choice. Does anyone know the answer or point me to information that would help me make the choice? I'm pretty sure the performance difference will be somewhat negligible also but still I'd like to make the optimal choice.

  Read the article

• Linux Mint Wireless doesn't connect [migrated]

  - by guisantogui

  I'm having a great problem, I've installed Linux mint debian edition (LMDE), and following this tutorial http://community.linuxmint.com/tutorial/view/161 I did installed the network driver. The available connections appears to me, but when i try to connect to my connection at first time, I got this message: "(4) Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken." And the following tries, I got this another message: "(32) Insufficient privileges." I'm accepting ideas. Thanks.

  Read the article

• How do i have 4GB of video memory with a 1GB video card?

  - by Tomas Spc Yaczik

  I ran the direct X diagnostic tool to take a look at my graphics capabilities and its telling me that the approximate video memory is clocked in at 4096MB. That doesn't make any sense, how is that possible? The only things that i can think of were that DirectX was inaccurate so i looked at the graphics statistics of my computer on CPU-Z which was included with the motherboard and that's telling me i have "negative" 1988MB. Not only is that not 4096MB, but its giving me a negative number and i know for a fact that you can't have a negative amount of memory???!!! The only things i can think of that would be amplifying my video memory output is the PCIe 3.0 bus, or that the motherboard is somehow including the on board video chip set with the video card which only then is only 2GB of video memory, which still has to be being amplified by something. Any suggestions?

  Read the article

• IT lead does not have a backup, DR plan in writing

  - by Alex

  This is a general management question to IT managers out there. We are a small firm with about 4 servers in our colo cabinent. No full time IT manager. But we do have one person on monthly contract and I am having a terrible time getting him to share what these plans actually are. I am sure he HAS a plan (and its probably in his head..) but that does us no good if he gets hit by a bus.. How would you guys handle this? He is a long time friend, but I fear this is dangerous for us long term..I have confronted him on several occasions about this, and he tells me not to worry, he has go it covered.. Thanks.

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• Is an Ethernet point to point connection without a switch real time capable?

  - by funksoulbrother

  In automation and control, it is commonly stated that ethernet can't be used as a bus because it is not real time capable due to packet collisions. If important control packets collide, they often can't keep the hard real time conditions needed for control. But what if I have a single point to point connection with Ethernet, no switch in between? To be more precise, I have an FPGA board with a giga-Ethernet port that is connected directly to my control PC. I think the benefits of giga Ethernet over CAN or USB for a p2p connection are huge, especially for high sampling rates and lots of data generation on the FPGA board. Am I correct that with a point to point connection there can't be any packet collisions and therefore a real time environment is given even with ethernet? Thanks in advance! ~fsb

  Read the article

• Can I be a wireless server WITHOUT offering internet?

  - by Kenny Hendrick

  I would like to pull into a truck stop and offer a folder of free documentaries to quell some of the ignorance LOL I run Linux ";-) Very happy to have made that switch by the way...and have an internal wireless in the laptop but my bus has an antenna on the roof which I connect via usb to create a wireless signal (this is the one I'd like to focus on since it will offer the most reach to all those truckers out there. My question is this. I'm running apache2 and have a bunch of videos tossed into the www folder and can access it locally and would like others that frown on paying to use the truckstops slow internet service and would like an alternative by simply logging onto me and getting the narrow content I offer freely without passwords and the like. Has anyone a good means of doing this? p.s. I've done this in the past but am getting old and forgetful (my crutch)

  Read the article

• CD/DVD burn error in ImgBurn and Nero

  - by bobby

  I am getting the errors shown below when I try to burn a CD/DVD on my DVD writer. I am seeing this error for every CD/DVD I try to burn. I am not able to write any CDs or DVDs using ImgBurn. The burn log below is a failed burn in Nero. What could be causing this error? Nero Burning ROM bobby 4C85-200E-4005-0004-0000-7660-0800-35X3-0000-407M-MX37-**** (*) Windows XP 6.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.11.3. Internal Version: 7, 11, 3, (Nero Express) Recorder: <HL-DT-ST DVDRAM GSA-H12N> Version: UL01 - HA 1 TA 1 - 7.11.3.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: <ATAPI-CD ROM-DRIVE-52MAX > Version: 52PP - HA 1 TA 0 - 7.11.3.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === === CDRom-Device-Map === ATAPI-CD ROM-DRIVE-52MAX F: CdRom0 HL-DT-ST DVDRAM GSA-H12N G: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981560kB) Free physical memory: 309MB (317024kB) Memory in use : 67 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 11.6.2010 CD Image 10:43:02 AM #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 10:43:02 AM #2 Text 0 File Burncd.cpp, Line 3186 HL-DT-ST DVDRAM GSA-H12N Buffer underrun protection activated 10:43:02 AM #3 Text 0 File Burncd.cpp, Line 3500 Turn on Disc-At-Once, using CD-R/RW media 10:43:02 AM #4 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 359848 ( 79:59.73) Last address to be written: 318783 ( 70:52.33) 10:43:02 AM #5 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 10:43:02 AM #6 Text 0 File DlgWaitCD.cpp, Line 2988 Recorder: HL-DT-ST DVDRAM G SA-H12N; CDR co de: 00 97 27 18; O SJ entry from: Pla smon Data systems Ltd. ATIP Data: Special Info [hex] 1: D0 00 A0, 2: 61 1B 12 (LI 97:27.18), 3: 4F 3B 4A ( LO 79:59.74) Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 0 0 00 (invalid) 10:43:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 10:43:02 AM #8 Text 0 File ThreadedTransferInterface.cpp, Line 785 Nero Report 1 Nero Burning ROM Setup items (after recorder preparation) 0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, Joliet) 2 indices, index0 (150) not provided original disc pos #0 + 318784 (318784) = #318784/70:50.34 not relocatable, disc pos for caching/writing not required/not required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318784 blocks [G: HL-DT-ST DVDRAM GSA-H12N] -------------------------------------------------------------- 10:43:02 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [G: HL-DT-ST DVDRAM GSA-H12N] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Se ssion Clo sed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next T rk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 6531768 32, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ -150 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 -150 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 318784 | 318784 | 0x00 318784 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 10:43:02 AM #10 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 10:43:02 AM #11 Text 0 File Burncd.cpp, Line 4286 Caching options: cache CDRom or Network-Yes, small files-Yes (<64KB) 10:43:02 AM #12 Phase 24 File dlgbrnst.cpp, Line 1767 Caching of files started 10:43:02 AM #13 Text 0 File Burncd.cpp, Line 4405 Cache writing successful. 10:43:02 AM #14 Phase 25 File dlgbrnst.cpp, Line 1767 Caching of files completed 10:43:02 AM #15 Phase 36 File dlgbrnst.cpp, Line 1767 Burn process started at 48x (7,200 KB/s) 10:43:02 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2733 Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0 10:43:02 AM #17 Text 0 File MMC.cpp, Line 17806 StartDAO : CD-Text - Off 10:43:02 AM #18 Text 0 File MMC.cpp, Line 22488 Set BUFE: Buffer underrun protection -> ON 10:43:03 AM #19 Text 0 File MMC.cpp, Line 18034 CueData, Len=32 41 00 00 14 00 00 00 00 41 01 00 10 00 00 00 00 41 01 01 10 00 00 02 00 41 aa 01 14 00 46 34 22 10:43:03 AM #20 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 10:43:16 AM #21 Text 0 File Cdrdrv.cpp, Line 1405 10:43:16.806 - G: HL-DT-ST DVDRAM GSA-H12N : Queue again later 10:43:42 AM #22 SPTI -1502 File SCSIPassThrough.cpp, Line 181 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1502) Sense Key: 0x04 (KEY_HARDWARE_ERROR) Nero Report 2 Nero Burning ROM Sense Code: 0x08 Sense Qual: 0x03 CDB Data: 0x2A 00 00 00 4D 00 00 00 20 00 00 00 Sense Area: 0x70 00 04 00 00 00 00 10 53 29 A1 80 08 03 Buffer x0c7d9a40: Len x10000 0xDC 87 EB 41 6E AC 61 5A 07 B2 DB 78 B5 D4 D9 24 0x8D BC 51 38 46 56 0F EE 16 15 5C 5B E3 B0 10 16 0x14 B1 C3 6E 30 2B C4 78 15 AB D5 92 09 B7 81 23 10:43:42 AM #23 CDR -1502 File Writer.cpp, Line 306 DMA-driver error, CRC error G: HL-DT-ST DVDRAM GSA-H12N 10:43:55 AM #24 Phase 38 File dlgbrnst.cpp, Line 1767 Burn process failed at 48x (7,200 KB/s) 10:43:55 AM #25 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 10:44:01 AM #26 Text 0 File Cdrdrv.cpp, Line 11412 DriveLocker: UnLockVolume completed 10:44:01 AM #27 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon Nero Report 3

  Read the article

• Strange messages on new Dell Workstation during bootup

  - by dan99t

  I recently installed Windows 7 Ultimate on a new Dell T-7500 Workstation, and am seeing some strange messages on the screen: Dell SAS 6 Host Bus Adapter BIOS MPTBIOS 6.22.03.00 ( 2008.08.06 ) Initializing….. Press Ctrl – C to run SAS Configuration Utility Searching for Devices at HBA 0….. Dell MPT Boot ROM Successfully installed Then it loads Windows 7. All of above happens on its own, I don't touch anything. So what is going on & what do I have to do get rid off those initializing commands ? I have never had this happen to any previously owned Dell systems. Also I haven't installed any drivers yet but Sound, Video & Internet does work. Do I need to install any additional drivers?

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• cloning mac address of physical server converted into vmware server

  - by user24981

  We've recently converted a physical Windows Server 2003 into vmware using P2V. However, one of the pieces of software on the 2003 machine are still looking for the old server's network MAC address in order to run. I've read several articles where it's discussed that you can modify the last part of the generated address and set it to static, but I need to clone the whole mac address to mimic the one in the old server. We're running CentOS and VMware server 2.0 as the host system. I was told that maybe adding in a second network card in the host and setting the virtual system's nic to that card instead of "bridged" would allow me to edit the vmx file and clone the whole MAC address. I can't use the old network card from the physical server because it's ISA and our new bus is PCI Any ideas? Thanks, Mike

  Read the article

• Sound does not work on the administrator profile.Works on a non-administrator profile on Windows XP

  - by Sharjeel Sayed

  Initially I suspected a missing driver, but then sound ( for movies,songs etc ) works fine on the other non-administrator account, but does not work when I log in to the Administrator account. And yes..I have checked the sound volume and mute status as well. Details of my system OS: Windows XP Professional Service Pack 3 (build 2600) Processor: 2.00 gigahertz AMD Athlon 64 Memory: 448 Megabytes Usable Installed Memory Board: ASUSTeK Computer Inc. K8V-MX Bus Clock: 200 megahertz BIOS: American Megatrends Inc. 0112 07/18/2005 Multimedia: SoundMAX Integrated Digital Audio Any help would be appreciated.Thanks in advance

  Read the article

• XFS and loss of data when power goes down

  - by culebrón

  Each time electricity goes down, my desktop (without UPS) loses some temporary information. Opera can lose settings, history, cache, or mail accounts (Thanks heavens I was wise to use IMAP). Partially or all together. a whole file (complete and save) in Geany appeared empty (and I didn't commit it to Git) rhythmbox lost all podcasts subscription data I'm afraid there are other losses I just didn't see. What's the reason? A memory files cache, a mem-disk? Or non-atomic file writes in xfs? I have Ubuntu 9.10 and XFS on both / and /home partitions. Is ext4 safer in such circumstances? I've seen ext3 is faster. Is it as safe as *4? Given that the apartment I rent is connected to a common bus and 1 safety switch for several apartments, and the neighbors - alone or together - overload it at least once every week, the lights go down often enough for this to be an issue.

  Read the article

• Buildcraft Minecraft mod causing crashes, NVIDIA-304xx Linux Drivers, KDE

  - by wolfo9999

  All is perfect, 96 fps average. Until an item tries to enter a buildcraft pipe. Tekkit instantly crashes, no error dialog. I have no idea what logs to look at for information on the crash, or how to fix it. OpenGL is enabled in KDE, Driver package is nvidia-304xx lspci output: VGA compatible controller: NVIDIA Corporation GT218 [Quadro FX 380M] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 172b Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d2000000 (32-bit, non-prefetchable) [size=16M] Memory at c0000000 (64-bit, prefetchable) [size=256M] Memory at d0000000 (64-bit, prefetchable) [size=32M] I/O ports at 5000 [size=128] [virtual] Expansion ROM at d3080000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia

  Read the article

• Unable to create context rendering error when run OpenGL application

  - by Rodnower

  Hello, I try to run Mesa gears example and I get following error: freeglut (./gears): Unable to create direct context rendering for window 'Gears' This may hurt performance. though the application runs successfully, but I guess that in future I will have much problems with productivity. I run Linux CentOS 5 on WMvare 7. Mesa's version is 6.5 Relevant output of lspci -v gives: 00:0f.0 VGA compatible controller: VMware SVGA II Adapter (prog-if 00 [VGA controller]) Subsystem: VMware SVGA II Adapter Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at 10d0 [size=16] Memory at d0000000 (32-bit, non-prefetchable) [size=128M] Memory at d8000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at 30000000 [disabled] [size=32K] Capabilities: [40] Vendor Specific Information Any one have idea? There is driver of vmvare for CentOS? Thank you for ahead.

  Read the article

• Dedicated GPU in Dell PowerEdge C1100

  - by Eli Gundry

  We recently purchased a Dell PowerEdge C1100 off lease with the initention of using it for graphics processing. We installed an AMD HD 7000 series GPU in it that runs off of board power and it sends video to the display. That said, the video is very choppy, leading us to belive that the onboard video is doing all the processing and sending it to the card. Is there any way to either disable the VGA on this server or tell the OS to only use the dedicated card. More info: The server is running REHL 6.4 The graphics running the proprietary AMD drivers The video card only works in OS and does not show the BIOS on boot (we know that it's impossible to change this) Any ideas, guys? Update We are now thinking that the GPU is doing the graphics processing, but not working at the full speed of the PCI bus. Which is odd, because it is an x16 slot, but probably optimized to use a RAID card (if that makes any sense). Is there any way to remedy the choppy graphics on this server?

  Read the article

• KVM Slow performance on XP Guest

  - by Gregg Leventhal

  The system is very slow to do anything, even browse a local folder, and CPU sits at 100% frequently. Guest is XP 32 bit. Host is Scientific Linux 6.2, Libvirt 0.10, Guest XP OS shows ACPI Multiprocessor HAL and a virtIO driver for NIC and SCSI. Installed. CPUInfo on host: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 42 model name : Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz stepping : 7 cpu MHz : 3200.000 cache size : 8192 KB physical id : 0 siblings : 8 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow vnmi flexpriority ept vpid bogomips : 6784.93 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: <memory unit='KiB'>4194304</memory> <currentMemory unit='KiB'>4194304</currentMemory> <vcpu placement='static' cpuset='0'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>SandyBridge</model> <vendor>Intel</vendor> <feature policy='require' name='vme'/> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='osxsave'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='ds'/> <feature policy='require' name='tsc-deadline'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='ht'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='force' name='sse'/> <feature policy='force' name='sse2'/> <feature policy='force' name='sse4.1'/> <feature policy='force' name='sse4.2'/> <feature policy='force' name='ssse3'/> <feature policy='force' name='x2apic'/> </cpu> <clock offset='localtime'> <timer name='rtc' tickpolicy='catchup'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2' cache='none'/> <source file='/var/lib/libvirt/images/Server-10-9-13.qcow2'/> <target dev='vda' bus='virtio'/> <alias name='virtio-disk0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x08' function='0x0'/> </disk>

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

< Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >