Search Results

Search found 36019 results on 1441 pages for 'access 2003'.

Page 393/1441 | < Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >

• Website hosted on IIS is not accessbile

  - by Tola Odejayi

  I have two sites set up in IIS on a remote machine RM; one on regular port 80, and the other on port 5773. From my local machine LM, I can access the site on 80, but I cannot access the one on 5773; I get a status code of 502 and an error code of 10060 (A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond) when I try to do this. I can access the 5773 site via IIS when I am logged into RM (i.e. by right clicking on a page on the site and going 'Browse'). I can also access pages on the 5773 site via a browser, again when I am logged into RM. I just can't do the same via a browser when I am logged into LM. I have ensured that port 5773 is open for outgoing traffic on LM. Could the problem be that I also need to ensure that port 5773 is open for inbound traffic on RM?

  Read the article

• How Do I Reset My Root Password on MySQL on a Mac?

  - by classicrock985

  I'm using SequelPro (http://www.sequelpro.com/) and I would like to know how to reset my root password. I'm trying to log in as host: localhost username: root password: (BLANK) but I keep getting this error: Unable to connect to host because access was denied. Double-check your username and password and ensure that access from your current location is permitted. MySQL said: Access denied for user 'root'@'localhost' (using password: NO) Any suggestions?!

  Read the article

• Connection to VPN using command line

  - by plurby

  I've wrote a simple batch file to connect to a specific VPN connection using RASDIAL rasdial MyVPNConnection but it always returned the error 691 Access denied because username and/or password is invalid on the domain. Remote Access Service (RAS) Error Code List then i tried pointing to my Remote Access Phonebook (Rasphone.pbk) and see what happens rasdial MyVPNConnection /phonebook:%userprofile%\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk and still there was an error 691. I've then unchecked the following but still the same problem was reported when executing my batch file.

  Read the article

• Trouble creating FTP in Server 2008

  - by Saariko

  I have been trying to create an FTP server on my new Server 2008. I have been following both (very detailed and highly published here guides) For setting up using IIS Manager http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/ and For anonymous FTP http://www.trainsignaltraining.com/windows-server-2008-ftp-iis7 I am able to log as an anonymous user. My need is to use a named user, so I need to use the IIS Manager. I get error 530 when trying to log as a user. Connected to 127.0.0.1. 220 Microsoft FTP Service User (127.0.0.1:(none)): ftpmanager 331 Password required for ftpmanager. Password: 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: Filename: Error: 530 End Login failed. ftp> I can not learn from this message anything. My password is set to: 1234 (so I don't think I make a mistake here - testing purposes only ofc) Thank you. Note - I went over other posts on SE that I read, and couldn't get the result: IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in. FTP Error 530, User cannot log in, home directory inaccessible. Having trouble setting up FTP server on Windows Server 2008 EDIT I think I found some errors with the physical path. Going to Basic settings, and Test Connection on the physical path, gave me the following error: The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again. I am not sure which/whom should get access to the Root folder !? I want to point out, I managed to login with a domain user (change authorization and authentication methods) but this is NOT the requested solution. I checked to make sure that the FTP, folders, access is working properly. I am bit lost here. ==== More tries: I have enabled another Allow rule for ALL Users. I still get the same error. It seems that it doesn't matter if i use a correct or wrong password, I still get Error 530.

  Read the article

• Apache2 Virtual Host broken; displayed default index.html on subdomain, but correct content on www.subdomain

  - by Robert K

  I've got a Linode configured as a Ubuntu 10.04.2 web server with Apache 2.2.14. I have a total of 4 sites, all defined under /etc/apache2/sites-available as virtual hosts. All sites are almost identical clones for configuration. And all sites but my last work successfully. default: (www.)exampleadnetwork.com (www.)example.com reseller.example.com trouble: client1.example.com I keep getting this page when I visit the client1.example.com site: It works! This is the default web page for this server. The web server software is running but no content has been added, yet. In my ports.conf file I have the NameVirtualHost correctly set to my IP address on port 80. If I access the "www.sub.example.com" alias the site works! If I access it without the www I see the "It Works" excerpt posted above. Even apache2ctl -S shows that my vhost file parses correctly and is added to the mix. My vhost configuration file is as follows: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName client1.example.com ServerAlias client1.example.com www.client1.example.com DocumentRoot /srv/www/client1.example.com/public_html/ ErrorLog /srv/www/client1.example.com/logs/error.log CustomLog /srv/www/client1.example.com/logs/access.log combined <directory /srv/www/client1.example.com/public_html/> Options -Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </directory> </VirtualHost> The other sites are variations of: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName example.com ServerAlias example.com www.example.com DocumentRoot /srv/www/example.com/public_html/ ErrorLog /srv/www/example.com/logs/error.log CustomLog /srv/www/example.com/logs/access.log combined </VirtualHost> The only site the differs is the other subdomain: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName reseller.example.com ServerAlias reseller.example.com DocumentRoot /srv/www/reseller.example.com/public_html/ ErrorLog /srv/www/reseller.example.com/logs/error.log CustomLog /srv/www/reseller.example.com/logs/access.log combined </VirtualHost> Filenames are the FQDN without the www. prefix. I've followed this advice, but still cannot access subdomain properly.

  Read the article

• Nginx deny doesn't work for folder files

  - by user195191

  I'm trying to restrict access to my site to allow only specific IPs and I've got the following problem: when I access www.example.com deny works perfectly, but when I try to access www.example.com/index.php it returns "Access denied" page AND php file is downloaded directly in browser without processing. I do want to deny access to all the files on the website for all IPs but mine. How should I do that? Here's the config I have: server { listen 80; server_name example.com; root /var/www/example; location / { index index.html index.php; ## Allow a static html file to be shown first try_files $uri $uri/ @handler; ## If missing pass the URI to front handler expires 30d; ## Assume all files are cachable allow my.public.ip; deny all; } location @handler { ## Common front handler rewrite / /index.php; } location ~ .php/ { ## Forward paths like /js/index.php/x.js to relevant handler rewrite ^(.*.php)/ $1 last; } location ~ .php$ { ## Execute PHP scripts if (!-e $request_filename) { rewrite / /index.php last; } ## Catch 404s that try_files miss expires off; ## Do not cache dynamic content fastcgi_pass 127.0.0.1:9001; fastcgi_param HTTPS $fastcgi_https; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; ## See /etc/nginx/fastcgi_params } }

  Read the article

• Unable to make the session state request to the session state server.

  - by Angry_IT_Guru

  For about 4-5 months now, I seem to be having this sporadic issue--mainly during our busiest time of the day between 10:30-11:45AM, where all my Windows 2003 web servers in a Microsoft NLB cluster start throwing session state server errors. A sample error is below. System.Web.HttpException: Unable to make the session state request to the session state server. Please ensure that the ASP.NET State service is started and that the client and server ports are the same. If the server is on a remote machine, please ensure that it accepts remote requests by checking the value of HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\aspnet_state\Parameters\AllowRemoteConnection. If the server is on the local machine, and if the before mentioned registry value does not exist or is set to 0, then the state server connection string must use either 'localhost' or '127.0.0.1' as the server name. at System.Web.SessionState.OutOfProcSessionStateStore.MakeRequest(StateProtocolVerb verb, String id, StateProtocolExclusive exclusiveAccess, Int32 extraFlags, Int32 timeout, Int32 lockCookie, Byte[] buf, Int32 cb, Int32 networkTimeout, SessionNDMakeRequestResults& results) at System.Web.SessionState.OutOfProcSessionStateStore.SetAndReleaseItemExclusive(HttpContext context, String id, SessionStateStoreData item, Object lockId, Boolean newItem) at System.Web.SessionState.SessionStateModule.OnReleaseState(Object source, EventArgs eventArgs) at System.Web.HttpApplication.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Now I'm using ASP.NET State service on a centralized back-end Windows 2003 server that all servers communicate to. I was originally using SQL Server state for a couple years as well prior to having this issue. The problem with SQL wqas that when the issue occurred, it created a blocking situation which essentially impacted all users across all servers. The product company recommended that I use the standard ASP.NET State service as that was what they technically supported. Why this would make a difference is beyond me -- but I had no choice but to try it! I have attempted to create multiple application pools, adding additional servers, chaning TCP/IP timeout from 20 to 30 seconds, and even calling Microsoft ASP.NET product support, with very little success. I even recommended that they review whether they are using read-only session state instead of read/write per page request -- as I understand that this basically causes every page to make round-trips to state server even if state isn't being used on the page. Unfortunately, the application is developed by our product company and they insist that it is something with my environment because other clients do not have these sort of issues. However, I've talked to other clients and they tell me when they've seen issues like they, they've basically had to create another web farm. This issue almost seems like I've simply reached some architectural limit within the application... Microsoft's position on the issue is that the session state needs to be reduced and the returncode being reported back from the state server indicates buffers are full. To better understand the scope of issues (rather than wait for customers to call and complain), I installed ELMAH and configured it to send me e-mails when unhandled exceptions occur. I basically get 500-1000 e-mails during the time period of high activity! If any one has any other ideas I could try or better ways to troubleshoot, I'd appreciate it.

  Read the article

• Where the heck is mod_login? (Joomla)

  - by Joey Adams

  I'm a Joomla newbie, and I'm trying to set up a site to require login access to certain articles. Simply setting the article's Access Level to Restricted makes it disappear rather than prompting for a login. I can't figure out how to make a login page because I can't find any menu items or documentation pertaining to mod_login. I want to set at least one page to require login access. Where do I start?

  Read the article

• What can prevent a Server 2008 machine accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. I don't think it is this because we have a 2003 Server machine behind a different hardware firewall and that one works fine. What on earth is left?!

  Read the article

• Can ping between Host and Guest, but can't acces webserver with Virtualbox

  - by Gastoni

  How come I can ping back and forth between host and guest using VirtualBox, but I can't access from the host the web server installed in the guest. I'm using a host-only network. Host Ubuntu 10.10 vboxnet0 - 192.168.56.1 ping to self, works ping to guest, works access to web server in guest, FAILS Guest Fedora 13 eth1 - 192.168.56.101 ping to self, works ping to host, works access to web server in host, works

  Read the article

• Taking stock of an existing ASA Firewall

  - by Nate

  Imagine you are given an existing network using an ASA firewall. The network works, but you aren't sure of anything else. The firewall may be completely improperly configured, with "outside" actually being inside and "inside" actually being outside, for all you know. My question is this: what are the commands to take stock of an existing ASA firewall setup? With only CLI access, how do I figure out: What interfaces are available The names of the interfaces The security levels attached to the interfaces The access-lists attached to the interfaces, including rules and directions I know how to set these things (interface, nameif, security-level, and access-list/access-group), but I don't know how to figure them out given an existing system. On a related note, is there anything else that I should worry about checking to make sure that the network isn't wide open? Thanks!

  Read the article

• Account not getting completed deleted within linux

  - by lbanz

  I've got a nas box running some flavour of linux 2.6.31.8.nv+v2 with an arm processor. It has got a samba share called 'all' that has full read write access to everyone. However one Windows machine cannot access it without prompting for authentication and I found out from the logs that the windows account matches a local account on the nas box. What I then went to do is delete the local account on the nas. I can see that /home,/etc/password + /etc/shadow the account doesn't exist anymore. However the samba logs, shows that it thinks it is still there as it says account is disabled. I've tried rebooting both nas + windows box. Is there somewhere else that it stores account information? I logged on with a different account on that Windows machine and I can access the share fine. The smb logs shows that it can't find the user and then allows anonymous access.

  Read the article

• Server 2008 R2 & Domain Trusts - Attempt to Compromise Security

  - by SnAzBaZ

  We have two separate Active Directory domains; EUROPE and US. There is a two way trust between the domains / forests. I have a group of users called "USA Staff" that have access to certain shares on servers in the EUROPE domain and a group called "EUROPE Staff" which have access to shares in the USA domain. Recently the USA PDC was upgraded to Windows Server 2008 R2. Now when I try to access a share on a USA server from a Windows 7 workstation in the EUROPE domain I get the "Please enter your username / password" dialog box appear, with a message at the bottom: "The system has detected a possible attempt to compromise security." When I enter a username / password for a user in the USA domain, I can then access the network resource. Entering credentials for a EUROPE user however does not give me access, even though my NTFS and Share permissions are set to allow that. Windows Server 2003 / Windows Server 2008 did not have this problem, it seems to be unique to R2. I found KB938457 and opened up port 88 on the Server 2008 R2 firewall but it did not make any difference. Any other suggestions as to what to turn off in R2 to get this working again ? Thanks

  Read the article

• How do I add permissions via command line for "everyone" on external HDD

  - by acidzombie24

  I have an external HDD and I kind of messed up the file permissions but when fixing it I thought it is ok bc with my username I can access the files perfectly fine. Now that I use this with two PC (actually ATM I don't have access to my other PC) I can't access these files. The problem is this directory has hundreds of folders with no permission for "everyone". I would like to give it the default permissions including have all access for the user "everyone". How do I do that via command line for these hundreds of folders?

  Read the article

• Windows 7: how can I add an IP range in the "route" command?

  - by KeyStroke

  Hi, I'm using two network connections, and I tried using the "route" command so that when I access a specific internal IP on my LAN, it would use connection 1, anything else would go normally through connection 2 (which doesn't have access to my LAN). The problem is I have a bunch of internal IP's that I need to access, and the "route" command doesn't seem to allow me to add an IP range instead of specific IP. And connection 1 doesn't have internet access, so I can't use it as my default connection. Any idea how this can be solved? Your help is appreciated

  Read the article

• Mac: Cannot open the parent directory Library

  - by rolandbishop

  I really am about to go crazy because nothing worked out. I'm trying to access the Library folder on my OS Lion however all the tutorials related to this subject involves opening the user library however I would like to access the Library where the 'WebServer' folder is located when you enable web-sharing. Whenever I try to access it it gives me the error that I am not allowed to see what's inside and I checked my status, saying that I am an admin but it still occurs. Any help?

  Read the article

• Is there a filesystem firewall?

  - by Jenko

  Ever since firewalls appeared on the scene, it became hard for rogue programs to access the internet. But you and I know that running applications get unrestricted access to the filesystem. They can read your files and send them to poppa. (programs such as web browsers and IM clients, which are allowed thru the internet firewall) Any way to know which programs are accessing your files? or limit their access to a specific partition?

  Read the article

• Multi- authentication scenario for a public internet service using Kerberos

  - by StrangeLoop

  I have a public web server which has users coming from internet (via HTTPS) and from a corporate intranet. I wish to use Kerberos authentication for the intranet users so that they would be automatically logged in the web application without the need to provide any login/password (assuming they are already logged to the Windows domain). For the users coming from internet I want to provide traditional basic/form- based authentication. User/password data for these users would be stored internally in a database used by the application. Web application will be configured to use Kerberos authentication for users coming from specific intranet ip networks and basic/form- based authentication will be used for the rest of the users. From a security perspective, are there some risks involved in this kind of setup or is this a generally accepted solution? My understanding is that server doesn't need access to KDC (see Kerberos authentication, service host and access to KDC) and it can be completely isolated from AD and corporate intranet. The server has a keytab file stored locally that is used to decrypt tickets sent by the users coming from intranet. The tickets only contain username and domain of the incoming user. Server never sees the passwords of authenticated users. If the server would be hacked and the keytab file compromised, it would mean that attacker could forge tickets for any domain user and get access to the web application as any user. But typically this is the case anyway if hacker gains access to the keytab file on the local filesystem. The encryption key contained in the keytab file is based on the service account password in AD and is in hashed form, I guess it is very difficult to brute force this password if strong Kerberos encryption like AES-256-SHA1 is used. As the server has no network access to intranet, even the compromised service account couldn't be directly used for anything.

  Read the article

• How to restrict Windows 7 internet data usage while using mobile connection?

  - by Daniel Gehriger

  When I'm travelling I would like to use my iPhone's mobile hotspot feature to provide Internet access for my Windows 7 laptop. However, my mobile data plan has a limit on the amount of data I can use per month, and I would like to restrict Internet access to a few very specific applications (such as a database administration tool and Chrome). Is it possible to create a firewall profile for use with mobile data access? If not, what tools exist that could assist me?

  Read the article

• OpenVZ multiple networks on CTs

  - by user6733

  I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

  Read the article

• MySQL stopped asking for passwords

  - by BlaM

  I'm currently experiencing a weird problem with one of my MySQL database servers: It stopped asking for passwords when I try to access the database from local with the mysql command line tool. I need a valid admin username. I also still need a password for remote access (i.e. from another IP). And I need a password when I - for example - access the database from a PHP script. But when I try to access the database from local host/commandline it will let me straight in to the data with my administrative users. They (admin users) have passwords set - and as I mentioned - I still need to specify those when I try to access the data via PHP. Changing the password didn't help. Non-Administrative users need to specify their passwort, but that doesn't really help if they can get anywhere with "mysql -u root" (or another admin user account name). (System Debian Linux Lenny, MySQL 5.0.51a) Any ideas? Anything that explains this behaviour? I don't understand how this can happen.

  Read the article

• Auto logon to internet provider

  - by user31673

  We use wireless internet access. The wireless is secured and to get an IP address, you provide the right key. That is setup just fine. However, on top of that, the first time we access the internet, a browser page appears and we have to enter a password. then we have access to the internet for a period of time. How can the password step be automated? I also have a web-based printer that doesn't work (except via USB connection) because it can't get out to the web. I can't change the router settings. Is there anything I can do to get the printer working and automatic the access?

  Read the article

• Port(s) not forwarding?

  - by user11189

  I have cable internet service through Charter Communications and feed two desktop computers through a Linksys RP614v3 router. One system is my wife's running WinXP Home Edition and the other is mine, running Vista Home Premium (sp1). I have port forwarding configured in the Linksys so I can access the Vista system remotely using TightVNC. Initially, it worked great and I was able to remotely tend email and access local files while out of town for work. Lately, the cable internet service appears to flicker intermittently and upon return, my Mailwasher program loses ability to access the net and I've been unable to make the remote connection. When I reset the port forwarded for email in the router control panel, Mailwasher functionality returns but as I'm home when that happens, I have no easy way to check remote access until the next time I'm on the road or at work. I'm at my wit's end -- the TightVNC client accesses fine from my wife's system from behind the modem/router setup but I don't know how to maintain whatever gets reset when I fiddle with the control panel and the need to do so at all is new. I accessed it fine for a week off and on while out of town a month ago and now I can't leave home and access it from work an hour later.

  Read the article

• Create new vsftpd user and lock to (specify) home / login directory

  - by Geoff Jackson

  I need to periodically give temporary and limited access to various directories on a CentOS linux server that has vsftp installed. I've created a user using useradd [user_name] and given them a password using passwd [password]. I've created a directory in /var/ftp and then I bind this to the directory that I wish to limit access to. What else do I need to specifically do to ensure that when this user logs into FTP, they only have access to this directory please?

  Read the article

• show user list command cisco 5500 ASA

  - by sorrrydoctorforlove

  simple issue.. I'm a noob I am running a cisco 5500 ASA which is used to manage a VPN, I need the command used to check the current user list. I think it might be an 'access-list', if so I have no idea what the name of the access list is, is there a way to show the access lists? thanks.

  Read the article

< Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >