Search Results

Search found 12310 results on 493 pages for 'andrew day'.

Page 394/493 | < Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >

• Why would my HDD main partition suddenly become hidden?

  - by Luis Oscar

  A few days ago I was using my computer as usual and I turned it off. The next day it wouldn't boot up. It just stayed after the hardware diagnostic window on the intermittent underscore screen. So clearly It wasn't booting up. I tried turning it on and off a couple of times with no avail. Finally I used windows 7 disk and it seemed as if there was no HDD. not even the installation would see the HDD. So i thought it was dead, i bought a new one installed it with windows and used a external case with the old HDD. plug it in and still couldn't see it. I finally downloaded a partition program EASUS or something and my HDD was there listed WITHOUT a system letter. I could however explore it and i set it as Unhidden and it came back to life. I could see it normally. I really just wish someone could explain to me what happened here, was it a virus? does it means the HDD is about to die? How can i prevent this or what should I do now? should i stop using this OLD HDD? Thanks

  Read the article

• 1GB cached memory - Do I need more RAM?

  - by Martin

  The server runs well but I wonder if I should get more RAM. I only have a few MB of "free" memory and 1.2GB of "cached" memory: free: total used free shared buffers cached Mem: 3945 3893 51 0 28 1216 -/+ buffers/cache: 2648 1296 Swap: 3895 857 3038 I learned that cached memory is used while it's free and not. Is the cached value an indicator for the need of more RAM? cat /proc/meminfo 1 day after flushing the cache: MemTotal: 4040048 kB MemFree: 32844 kB Buffers: 18956 kB Cached: 1249092 kB SwapCached: 161576 kB Active: 3611328 kB Inactive: 189104 kB SwapTotal: 3989496 kB SwapFree: 2894200 kB Dirty: 20520 kB Writeback: 0 kB AnonPages: 2523496 kB Mapped: 217744 kB Slab: 70940 kB SReclaimable: 36756 kB SUnreclaim: 34184 kB PageTables: 99648 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 6009520 kB Committed_AS: 6401716 kB VmallocTotal: 34359738367 kB VmallocUsed: 18852 kB VmallocChunk: 34359719439 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB top: top - 17:20:10 up 112 days, 3:06, 1 user, load average: 1.01, 1.62, 1.48 Tasks: 208 total, 1 running, 207 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.6%sy, 0.0%ni, 97.5%id, 1.3%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 4040048k total, 3953108k used, 86940k free, 16348k buffers Swap: 3989496k total, 1095712k used, 2893784k free, 1235436k cached

  Read the article

• Disaster After Removing Two HDD From LaCie RAID 0 Case

  - by John

  This is the second time this has happened. I own a LaCie IDE RAID 0 Enclosure and the RAID went bad. The system gave me a warning that the data could be read from the RAID but that nothing could be written, and to remove the data ASAP. I did that and erased and reinitialized the RAID. System reported it was fine, no issues. I wrote to the RAID again and the system reported the same issue. So, I removed the drives and tested them individually thinking one must have gone bad. Sure enough, one HDD reported all bad blocks, every single one after the Master Boot Record. I didn't think much about it because of the age of the drives, 5 years old. So, I bought two new drives plugged them in and started up the RAID again. Exactly the same thing happened. All was fine after initializing the RAID and then the next day after powering on the RAID the exact same issue. The HDD sitting in the same position as the first "bad" HDD reported all bad blocks. Obviously, this is an issue with LaCie's bridge board not with the drives. No utility I have used has been able to bring this HDD back to life. I thought I would just copy the MBR from the good drive to the new one using a sector editor but am hesitant. Is it possible the firmware on the HDD has been corrupted by the LaCie bridge board?? What else could be the cause of such an issue? How can I fix this drive?

  Read the article

• Thunderbird: how to move mails into correct thread? (mailing lists)

  - by unor

  I'm subscribed to some mailing lists and every day people reply to a wrong mail (or they don't reply at all), so that their mail lands in the wrong (or a new) thread. I set the mail display in "View ? Sort by" to "Threaded". Example: mailing list "Foobar": [Foobar] random topic Re: [Foobar] random topic Re: [Foobar] random topic Re: [Foobar] random topic Re: [Foobar] random topic [Foobar] I'm John Doe Re: [Foobar] I'm John Doe Re: [Foobar] Welcome, John Re: [Foobar] random topic There are two discussions, one about "random topic", one about "John Doe". The subject line changes in the discussion about John Doe, which is fine (no problem here). But the last mail should be pigeonholed in the first thread. Instead it is at the top-level. Now, how can I move that last mail into the correct thread? I tried to drag&drop it at the mail I think it should be a reply to, but this doesn't work. I think theoretically it should be possible by fiddling with the mail headers after receiving the mail, but this doesn't seem to be a comfortable way.

  Read the article

• WT-NMP - PHP-CGI randomly stops running with no error log

  - by alexfontaine

  We have recently installed WT-NMP and are currently running Php-Cgi with php 5.4.24. We are running fairly simple php scripts and when testing everything is running fine. Over the weekend we wanted to keep the server running test it over a longer period of time. The server and scripts ran fine all day on Friday, but sometime late on Saturday, the php-cgi stopped running. There are no errors in the error log (C:\WT-NMP\log). In the configuration (php.ini) I have the following options set: error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On html_errors = On error_log = "c:/wt-nmp/log/php_error.log" We also have the standard nginx.conf error logs: access_log "c:/wt-nmp/log/nginx_access.log"; error_log "c:/wt-nmp/log/nginx_error.log" warn; So, since the log directory is empty, I am assuming that the running php scripts and general nginx operations are not causing the php-cgi to stop. So my questions are: What else could cause the php-cgi to stop running? Are there any other options for logging that we could turn on that could help us track this down? Are there other log locations that we should be looking at? Thanks!

  Read the article

• How can I tell which page is creating a high-CPU-load httpd process?

  - by Greg

  I have a LAMP server (CentOS-based MediaTemple (DV) Extreme with 2GB RAM) running a customized Wordpress+bbPress combination . At about 30k pageviews per day the server is starting to groan. It stumbled earlier today for about 5 minutes when there was an influx of traffic. Even under normal conditions I can see that the virtual server is sometimes at 90%+ CPU load. Using Top I can often see 5-7 httpd processes that are each using 15-30% (and sometimes even 50%) CPU. Before we do a big optimization pass (our use of MySQL is probably the culprit) I would love to find the pages that are the main offenders and deal with them first. Is there a way that I can find out which specific requests were responsible for the most CPU-hungry httpd processes? I have found a lot of info on optimization in general, but nothing on this specific question. Secondly, I know there are a million variables, but if you have any insight on whether we should be at the boundaries of performance with a single dedicated virtual server with a site of this size, then I would love to hear your opinion. Should we be thinking about moving to a more powerful server, or should we be focused on optimization on the current server?

  Read the article

• iptables port forwarding works only for localhost

  - by Venki

  Below is my iptables config. I used this for my accessing a node js website running in port 9000 through port 80. This works fine only if access the website through local host / loop back. When I try to use the ip of eth0, which is assigned by my router through dcp. this does not work, when I use ip like 192.168.0.103 to access the website. I am not able to figure what is wrong here, Already burnt a day in this, still not able to figure out :( Edit: ( more information) Earlier, I was using this configuration to develop the website, i had configured the domain name to point to 127.0.0.1 in the /etc/hosts file. It was working fine, but now I am trying to deploy the website in a vps with static ip, This configuration does not work with both static IP. # redirect port 80 to port 9000 *nat :PREROUTING ACCEPT [57:3896] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [4229:289686] :POSTROUTING ACCEPT [4239:290286] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 9000 -A OUTPUT -d 127.0.0.1/32 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 9000 COMMIT # Allow HTTP and HTTPS connections from anywhere (the normal ports for websites and SSL). -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT -A INPUT -p tcp --dport 9000 -j ACCEPT -A INPUT -j REJECT

  Read the article

• Calendar sharing between unrelated Domains

  - by vlannoob

  I have a 'request' from one of the 'big guys' that has me scratching my head a bit. He is one of our Executives that also is a board member of several other organistations, so he floats around between 4 different unrelated companies, each with their own domains, Exchange setup etc. He has domain accounts in each organisation. He has an iPad with multiple Exchange accounts so he can see all his calendars which works Ok for him - Apple calendaring bugs/flaws aside. What he wants is the ability for 'reception staff' at each organisation to 'see' all his calendars as they are booking things for him in their respective organisations calendars without it conflicting with bookings made in his calendars by other organisations......you with me?? So for example: Company A books a meeting into his Comapny A calendar at 9am Monday and Company B books him a meeting in his Company B Calendar at 9:15am Monday on the other side of town and of course Company C has him booked in all day Monday on their Company C calendar. He gets all those on his iPad but he would like either a 'global' calendar all can see and book into or the ability for receptionists at Company's A,B and C to see all the Calendars to avoid these kind of conflicts. I told him to 'go away' straight off the bat, I don't control anything to do with the other companies or know their infrastructure. And quite frankly I don't want any part of it...but he's whining and he's high enough up the food chain that I can't ignore him forever. I'm open to suggestions. Is there any third party software/services that can facilitiate this kind of setup? I really don't want to be creating users in my AD structure to people not ion our organisation so they can get access to his calendar and I am sure there sysadmins feel the same. As usual - any advice is greatly appreciated ;)

  Read the article

• What LTO 4 drive to buy

  - by pplrppl

  Evan Anderson mentioned in another solution you could buy a LTO-4 (autoloader, 1 tape / day) - $4,566.00 (the discussion included total cost of tapes for a specific rotation.) but I don't know specifics on what he or you would recommend for the actual drive and if necessary controller. Show me a newegg URL or CDW, Dell, or HP, or whatever your favorite vendor would be for your solution if you don't mind looking it up or just give me a brand and a model number and I'll be glad to do the leg work myself. I currently have on have on hand an external LTO 3 drive that uses LVD SCSI interface (and thus have a controller card that has an external LVD SCSI connector). If that card isn't sufficient to interface to a LTO 4 drive let me know. http://www.fujifilmusa.com/shared/bin/LTO_Overview.pdf shows minimum tape speeds for LTO4 and other LTO formats. It looks like the IBM LTO4 actually has a lower minimum speed than the IBM LTO3. Either way my average server is too slow to feed LTO3/4 without shoeshining so I'm looking for a drive with a low minimum write speed. If you trust the PDF from 2008 that makes my choices IBM LTO 4 full height IBM LTO 4 half height HP LTO 4 half height but presumably there are other options out there that weren't mentioned in the fuji PDF. Again I'm looking for a specific recommendation on a drive to buy (and the controller if needed).

  Read the article

• About Load average in htop, how to decide if it's still doing ok?

  - by Joe Huang

  I use 'htop' to monitor my web server. It's recently quite loaded and the Load average is showing something like this: Load average: 3.10 2.56 1.63 I searched the web about these numbers and I found an article about it: http://blog.scoutapp.com/articles/2009/07/31/understanding-load-averages In the article, it says if I have 2 CPUs, 2.0 means 100% CPU utilization. And my VPS has two CPUs, so what does 3.1 mean? How could it exceed 100% CPU utilization? And from these numbers, does it mean I should be wary about the loading now? But the performance seems totally fine, and this is a managed VPS, the hosting company has not notified me any warning about it. During day time, Load average always show these high numbers... here is another snapshot while writing. Load average: 3.03 2.77 1.97 Load average: 0.41 1.29 1.60 <---- 5 more minutes later So I am wondering how much room left for this site to grow in current configurations? What kind of proactive actions I should take in advance? I don't want to wait until the server bursts. Thanks.

  Read the article

• Tomcat web application intermittent freeze

  - by tinny

  I have a Grails web application (just a standard war file) deployed on a Ubuntu 10.10 server running on tomcat 6. My database is postgresql. The problem is that every so often (once or twice a day after inactivity) when I try to log into this web application it just freezes. I can navigate to the login page but when I try and login (first time the DB is hit, might be a clue..?) the application just freezes indefinitely, no 500 response code... the browser just waits and waits. I followed the instructions detailed here because the problem described sounded the same as mine. My GC logging showed no long running GC, all sub sec. When the application freezes a jmap heap output is... using parallel threads in the new generation. using thread-local object allocation. Concurrent Mark-Sweep GC Heap Configuration: MinHeapFreeRatio = 40 MaxHeapFreeRatio = 70 MaxHeapSize = 536870912 (512.0MB) NewSize = 21757952 (20.75MB) MaxNewSize = 87228416 (83.1875MB) OldSize = 65404928 (62.375MB) NewRatio = 7 SurvivorRatio = 8 PermSize = 21757952 (20.75MB) MaxPermSize = 85983232 (82.0MB) Heap Usage: New Generation (Eden + 1 Survivor Space): capacity = 19595264 (18.6875MB) used = 11411976 (10.883308410644531MB) free = 8183288 (7.804191589355469MB) 58.23843965562291% used Eden Space: capacity = 17432576 (16.625MB) used = 9249296 (8.820816040039062MB) free = 8183280 (7.8041839599609375MB) 53.05754009046053% used From Space: capacity = 2162688 (2.0625MB) used = 2162680 (2.0624923706054688MB) free = 8 (7.62939453125E-6MB) 99.99963008996212% used To Space: capacity = 2162688 (2.0625MB) used = 0 (0.0MB) free = 2162688 (2.0625MB) 0.0% used concurrent mark-sweep generation: capacity = 101556224 (96.8515625MB) used = 83906080 (80.01907348632812MB) free = 17650144 (16.832489013671875MB) 82.62032270912317% used Perm Generation: capacity = 85983232 (82.0MB) used = 62866832 (59.95448303222656MB) free = 23116400 (22.045516967773438MB) 73.1152232100324% used Anyone know what "From Space:" is? Any ideas on further fault finding ideas? I dont have much experience with this type of fault finding.

  Read the article

• exim4 redirect mail sent to *@domain1.example.com to *@domain2.example.com

  - by nightcoder

  Current situation: We have a VPS that hosts a website example.org. Exim is configured to work as a smarthost. All emails sent through exim are successfully relayed to another mail server (that is working on example.com). Goal: To forward mail sent to *@example.org to *@example.com, i.e. change the recipient's address from *@example.org to *@example.com. Problem: If I send email to address *@example.org, then it seems exim doesn't change the address, it still relays the message to another mail server but recipient is still *@example.org. Maybe the redirect is not applied for some reason. Configuration and logs: /etc/exim4/update-exim4.conf.conf: dc_eximconfig_configtype='smarthost' dc_other_hostnames='' dc_local_interfaces='' dc_readhost='example.org' dc_relay_domains='example.org' dc_minimaldns='false' dc_relay_nets='0.0.0.0/32' dc_smarthost='example.com::26' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='true' dc_mailname_in_oh='true' dc_localdelivery='maildir_home' /etc/exim4/conf.d/router/999_exim4-config_redirect (created by me): domain_redirect: debug_print = "R: forward for $local_part@$domain" driver = redirect domains = example.org data = [email protected] (for now data is set to a specific address for simplicity and testing) exim log when sending email to [email protected] (should be redirected to [email protected]): 2012-03-20 19:40:07 1SA4ud-0005Dw-7k <= [email protected] U=www-data P=local S=657 2012-03-20 19:40:08 1SA4ud-0005Dw-7k => [email protected] R=smarthost T=remote_smtp_smarthost H=domain2.com [184.172.146.66] X=TLS1.0:RSA_AES_256_CBC_SHA1:32 DN="C=US,2.5.4.17=#13053737303932,ST=TX,L=Houston,STREET=Suite 400,STREET=11251 Northwest Freeway,O=HostGator.com,OU=HostGator.com,OU=Comodo PremiumSSL Wildcard,CN=*.hostgator.com" 2012-03-20 19:40:08 1SA4ud-0005Dw-7k Completed So, the address is not changed :( Please help! I'm trying to make it work for half a day already :(

  Read the article

• If spambots are filling out forms on my website, should I mark the mail as spam?

  - by rob

  Apparently spambots have discovered the contact forms my website. I'm considering adding a CAPTCHA, but in the meantime I've been getting dozens of completed website forms in my Gmail account each day. I know I can configure a filter to always allow e-mails from my website to be delivered (i.e., "never send to spam"), but I'm wondering whether there are also larger implications. At first, I was marking the spam forms as spam because I figured it would block the sender's e-mail address from getting through again. But since then, I've given it some more thought. I know many spam filters use Bayesian filters and other techniques to identify spam based on its content. If I mark all these e-mails as spam, will legitimate e-mails from my website be marked as spam? Even if I stop marking the messages as spam, I can see another potential problem. My form is pretty standard (in fact, it's probably very similar to other online forms). If I mark my spambot-submitted website forms as spam, will Gmail begin to mark other people's similar-looking messages as spam?

  Read the article

• Is there a way to force spam-filter to change their policy or remove them as recognized spam service?

  - by Alvin Caseria

  As per mxtoolbox I got 1 blacklist still active for quite sometime now. UCEPROTECTL1's is running on 7 day policy since last spam mail. This is too strict compared to the 98 other spam filters out there as per mxtoolbox. (Or at least to the other 4 that detected the problem) I have no problem with our e-mail since it is hosted locally. But our domain is hosted outside the country and it run on a different IP. I contacted them but since it is the spam-filter's rule, there's nothing to be done but wait. I do believe services like spam-filters should at lease be bounded by guidelines and standards for this matter. Otherwise problem on delivering valid (after the fix) e-mails will be disastrous. Is there a way to force UCEPROTECT to change their policy or remove them as recognized spam service? Apart from contacting them in case they do not answer. Currently they are charging for fast removal if you pay by PayPal. I'm still looking for guideline/standard on how they should operate regarding this matter. Appreciate the help.

  Read the article

• Windows 7 "freezes" (chills?), and then "unfreezes" after about 1 minute.

  - by gbc001

  Hi, I have an Acer Timeline 1810T netbook (4GB RAM) with Windows 7 x64. About once or twice a day, it "freezes" - the reason I put this in quotation marks is that it does not really freeze, as I you cant move mouse, etc. I can move my mouse and jump between different applications, but I cant use the applications for anything. So I can jump between notepad and Firefox, but I cant browse to a new web page. I have been trying to determine the source of this misery for a while now, and I suspect it has something to do with the hard drive - indirectly if not directly. Here are some screen shots of the resource monitor during a "freeze" and during normal operation: Freeze: http://imgur.com/Gcgq1.jpg Normal operation: imgur.com/mlHaI.jpg As you can see, CPU is fine during freeze, but the disk is going bananas.. Does anyone have an idea of what these reading means, or about the problem in general? There seems to be no specific activity that sets this off - it can be during browsing, or during media playback with nothing else open. The fact that I can see navigate to applications but not use them might suggest a hard drive problem as well? Maybe I can access the stuff that is in RAM, but not anything that would require interaction with the drive.. Very appreciative of any help!

  Read the article

• Problem importing pictures from a digital camera with Windows 7

  - by snark

  Hi, Since I'm using Windows 7 (Beta, then RC, now RTM), I have issues when I download pictures from my digital cameras. It happens with my 2 cameras: a Canon Powershot S2 IS and a Canon Ixus 80 IS. When I plug a camera (any of them) to a USB port and switch it on in Play mode, the Autoplay function of Windows 7 starts with this screen: I select "Import pictures and videos" to call the native Windows 7 tool. It searches a bit for pictures to download from the camera and starts the transfer. However, during the transfer, I often get errors like this one: If I use "Try again", it works fine the second time and the picture is retrieved correctly. It's very annoying when it happens 20 or 30 times in a 500-picture download. I cannot leave it running standalone, as I have to watch for the errors and click on "Try again". Any idea what is causing these errors? I tried changing the USB port (normally the cameras are connected via a USB hub but it happens also when I connect them directly to a MB USB port) and the USB cable, but no success. I also checked the SD card by connecting them with a card reader and running a ChkDsk on them but it found no errors on the cards. Update: No problem when I copy the pictures manually with the Windows Explorer. And no problem either when I access the card with a reader. The builtin import tool of Windows is convenient as it sorts the pictures automatically by date (1 folder per day). And this is the way I sort my pictures

  Read the article

• POST Fail via AJAX Request?

  - by Jascha

  I can't for the life of me figure out why this is happening. This is kind of a repost (submitted to stackoverflow, but maybe a server issue?). I am running a javascript log out function called logOut() that has make a jQuery ajax call to a php script... function logOut(){ var data = new Object; data.log_out = true; $.ajax({ type: 'POST', url: 'http://www.mydomain.com/functions.php', data: data, success: function() { alert('done'); } }); } the php function it calls is here: if(isset($_POST['log_out'])){ $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('logOutSuccess')"; $connection->runQuery($query); // <-- my own database class... // omitted code that clears session etc... die(); } Now, 18 hours out of the day this works, but for some reason, every once in a while, the POST data will not trigger my query. (this will last about an hour or so). I figured out the post data is not being set by adding this at the end of my script... $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('POST FAIL')"; $connection->runQuery($query); So, now I know for certain my log out function is being skipped because in my database is the following data: if it were NOT being skipped, my data would show up like this: I know it is being skipped for two reasons, one the die() at the end of my first function, and two, if it were a success a "logOutSuccess" would be registered in the table. Any thoughts? One friend says it's a janky hosting company (hostgator.com). I personally like them because they are cheap and I'm a fan of cpanel. But, if that's the case??? Thanks in advance. -J

  Read the article

• Backup and Archive Strategy Question

  - by OneNerd

  I am having trouble finding a backup strategy for our code assets that 'just works' without any manual intervention. Goal is to have an off-site backup (a synchronized one) so that when we check-in files, create builds, etc. to the network drive, the entire folder structure is automatically synchronized and backed-up (in real time, or 1x per day) at some off-site location so if our office blows up, we don't lose all of our data. I have looked into some online backup services, but have not yet had any success. Some are quirky/buggy, others limit file size and/or kinds of files (which doesn't work well for developer files). Everything gets checked in and saved to a single server (on a Raid Mirror), so we just need to have a folder on that server backed up/synchronized to some off-site location. So my question is this. What are you using for your off-site backup strategy. What software, system, or service? Is there a be-all/end-all system of backing up your code assets that I just haven't found yet? Thanks

  Read the article

• Windows XP consuming drive letters

  - by billdehaan

  This one's a bit of a stumper. I'm running XP SP3, current with all fixes, etc. My problem is that I can assign a drive letter to a container file (explained below), it works just fine. But once I close the container, the drive letter is no longer available until the next boot. I've got some confidential data that I've placed in a container volume. I've used TrueCrypt (www.truecrypt.com) and FreeOTFE (www.freeotfe.org), with both installed and portable versions for both, with the same result. I open the container file, assign it to a drive letter (say R:), and run some portable apps that are within the volume. When I'm done, I close the container, and the drive letter is released. Fine so far. However, when I attempt to re-open it, the previous drive letter (in this case R:) is no longer available. It's not mapped to anything, it's just unavailable. Even attempting something like "subst R: C:\" returns "Invalid Parameter - R:". I can use the S: drive, no problem, but the next day I have to use T:, then U:, etc. Eventually, I have to reboot to reclaim all of of the drive letters. Unfortunately, everything I've read about drive letters relates to USB assignments, which doesn't apply here. I've tried the "show hidden" command (set devmgr_show_nonpresent_devices=1) with no success. And the Disk Management tool doesn't apply either, since it's not a physical drive. Does anyone know where Windows keeps the list of drive letters? And is there anything short of a reboot that can be used to reset it?

  Read the article

• Is there a small business router that shows bandwidth usage graphs in the admin panel?

  - by Robert Drake

  I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

  Read the article

• SQL 2008 Replication corrupt data problem

  - by Jonathan K

  We took a SQL 2000 database. Took a lightspeed backup. Restored on SQL 2008 active/passive cluster. Then setup replication to replicate the data back to SQL 2000. So 2008 is the publisher/distributor, and 2000 is doing a pull subscription. Everything works well, execpt we occassionally get corrupt data in varchar/text fields on the subscriber. So for example we have a table with 4500 records. When we run this statement: update MedstaffProvider set Notes = 'Cell Phone: 360.123.4567 Answering Service: 360.123.9876' where LastName = 'smith' The record in the 2008 database is updated as expected. But in the subsriber datbase we'll get gibberish in the notes field: óPÌ[1] T $Oé[1] ð²ñ. K Here's what we know: This is repeatable, meaning we can run that same query all day long and get the same gibberish. If you alter update statement slightly the data gets replicated just fine. The collation on both databases is the same. So far we've only detected the problem with text/varchar fields. (The notes field above is text). Only one or two records in a table are impacted. The table structure looks identical in both 2000/2008. We haven't made any changes. We have found one solution that fixes the problem. Basically if we recreate the table in 2008 (say as MedStaffProvider2) and then insert all the data. Drop the original table. Rename the table to it's original name. Setup replication again. And run the exact same update statement it works as expected. Does anyone have any idea what might be happening here? Or are there any other techniques we can use to troubleshoot this? I've found a solution for this, but would really like to undertsand why this is happening.

  Read the article

• Overclock Failed

  - by John

  This morning when I tried to turn on my computer, the monitor would not display anything. The computer is on, but no UI on the monitor and no beep. I turned off the computer and turn it back on again. This time, the computer was on for about 2 seconds and automatically turned itself off for about 2 second and automatically turned itself back on. This happened two times without the monitor displaying any UI. On the third try, the computer did the same thing but when it turned itself back on, the monitor displayed this: American Megatrends Asus P8P67 Le ACPI bios Revision 1011 CPU Intel Core i5 2500K CPU @ 3.30GHz Speed: 3300MHz Total Memory 4096 MB (DDR3-1333) USB Devices Total: 0 Drive, 1 Keyboard, 1 Mouse, 2 Hubs Detected ATA/ATAPI Deivces SATA6G_2 Hitachi HDs821010CLA 332 SATA3G_1 Corsair force 3 SSD SATA3G_2 HL-DT-ST DB-RE UH12CS28 Overclocking Failed! Please enter setup to reconfigure your system. Press F1 to Run Setup. After I pressed F1, it went into the Asus EF1 Bios Utility. I couldn't do anything in there so I just exited. After which, the computer auto turned off and on again and I was able to use the PC like regular. This has never happened to this computer before and the day before, nothing seemed wrong, just regular use and some gaming.

  Read the article

• fast way to find network user computer on domain hogging all wan bandwidth

  - by dasko

  i have a network of about 40 domain users and i have huge latency wan issues, like 1400ms for google.com pings. I have noticed that the problem goes away after everyone goes home for the day. I would like to know if i should use something like a hub with wireshark on the router or modem to see if there are any irregular activity. I am open to suggestions but i need to isolate which user has the bug. I am assuming it is either downloads or someone spamming out heavily and not knowing. It would be best to trace to ip number so i can just look into dns and find the pc hostname with the problem? This is the first client i have this problem with so never really needed to address it before but not suprised as users don't actually listen to any best practices that we have suggested. Please help, thanks. just to update, pc's to routers and other computers have ping latency of 1ms so it is right after i hit the wan, using tracert to a web site (random), that i get the massive delay in the responses. As well this is a dsl line with 5mb down and 650kb up (maybe upload saturation?) thanks.

  Read the article

• Mac Security - Which one?

  - by Bob Rivers

  Hi, Recently I had my credit card cloned. A few hours after shopping at an online store (in which I trust and buy since 2006) I received a call from my bank asking if I recognize a $5,000 debt to a store(?!) called Church of Christ... I'm a Mac user (OS X 10.6.3). I always kept my system updated and I have firewall enabled (in my Mac and in my broadband router), but I decided to adopt some kind of protection. I don't want to rise passionate discussions. Real or not, snake oil or not, I need to have back my peace of mind... I read this and this posts. I selected two software that I think that could help me (both have more features other than just an antivirus). Does someone have feedback about Intego's VirusBarrier X6 or Trendmicro's Smart Surfing? Intego solutions seems to be better, but TrendMicro brand/name is stronger in corporate environment, so their solution should be good. Both solutions have 30 day free trial, but I would like to hear something from you. Any other solution that I should look? TIA, Bob

  Read the article

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

< Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >