Search Results

Search found 10481 results on 420 pages for 'port mirroring'.

Page 394/420 | < Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >

• Slow boot on Ubuntu 12.04

  - by Hailwood

  My Ubuntu is booting really slow (Windows is booting faster...). I am using Ubuntu a Dell Inspiron 1545 Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 4GB Ram, 500GB HDD running Ubuntu 12.04 with gnome-shell 3.4.1. After running dmesg the culprit seems to be this section, in particular the last three lines: [26.557659] ADDRCONF(NETDEV_UP): eth0: link is not ready [26.565414] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.355355] Console: switching to colour frame buffer device 170x48 [27.362346] fb0: radeondrmfb frame buffer device [27.362347] drm: registered panic notifier [27.362357] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on minor 0 [27.617435] init: udev-fallback-graphics main process (1049) terminated with status 1 [30.064481] init: plymouth-stop pre-start process (1500) terminated with status 1 [51.708241] CE: hpet increased min_delta_ns to 20113 nsec [59.448029] eth2: no IPv6 routers present But I have no idea how to start debugging this. sudo lshw -C video $ sudo lshw -C video *-display description: VGA compatible controller product: RV710 [Mobility Radeon HD 4300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:48 memory:e0000000-efffffff ioport:de00(size=256) memory:f6df0000-f6dfffff memory:f6d00000-f6d1ffff After loading the propriety driver my new dmesg log is below (starting from the first major time gap): [2.983741] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [25.094327] ADDRCONF(NETDEV_UP): eth0: link is not ready [25.119737] udevd[520]: starting version 175 [25.167086] lp: driver loaded but no devices found [25.215341] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [25.215345] Disabling lock debugging due to kernel taint [25.231924] wmi: Mapper loaded [25.318414] lib80211: common routines for IEEE802.11 drivers [25.318418] lib80211_crypt: registered algorithm 'NULL' [25.331631] [fglrx] Maximum main memory to use for locked dma buffers: 3789 MBytes. [25.332095] [fglrx] vendor: 1002 device: 9552 count: 1 [25.334206] [fglrx] ioport: bar 1, base 0xde00, size: 0x100 [25.334229] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [25.334235] pci 0000:01:00.0: setting latency timer to 64 [25.337109] [fglrx] Kernel PAT support is enabled [25.337140] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [25.342803] Adding 4189180k swap on /dev/sda7. Priority:-1 extents:1 across:4189180k [25.364031] type=1400 audit(1338241723.027:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=606 comm="apparmor_parser" [25.364491] type=1400 audit(1338241723.031:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=606 comm="apparmor_parser" [25.364760] type=1400 audit(1338241723.031:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=606 comm="apparmor_parser" [25.394328] wl 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [25.394343] wl 0000:0c:00.0: setting latency timer to 64 [25.415531] acpi device:36: registered as cooling_device2 [25.416688] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:34/LNXVIDEO:00/input/input6 [25.416795] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [25.416865] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work. [25.425133] lib80211_crypt: registered algorithm 'TKIP' [25.448058] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [25.448321] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [25.448353] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [25.738867] eth1: Broadcom BCM4315 802.11 Hybrid Wireless Controller 5.100.82.38 [25.761213] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [25.761406] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [25.783432] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [25.908318] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro [25.928155] input: Dell WMI hotkeys as /devices/virtual/input/input9 [25.960561] udevd[543]: renamed network interface eth1 to eth2 [26.285688] init: failsafe main process (835) killed by TERM signal [26.396426] input: PS/2 Mouse as /devices/platform/i8042/serio2/input/input10 [26.423108] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio2/input/input11 [26.511297] Bluetooth: Core ver 2.16 [26.511383] NET: Registered protocol family 31 [26.511385] Bluetooth: HCI device and connection manager initialized [26.511388] Bluetooth: HCI socket layer initialized [26.511391] Bluetooth: L2CAP socket layer initialized [26.512079] Bluetooth: SCO socket layer initialized [26.530164] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [26.530168] Bluetooth: BNEP filters: protocol multicast [26.553893] type=1400 audit(1338241724.219:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=928 comm="apparmor_parser" [26.554860] Bluetooth: RFCOMM TTY layer initialized [26.554866] Bluetooth: RFCOMM socket layer initialized [26.554868] Bluetooth: RFCOMM ver 1.11 [26.557910] type=1400 audit(1338241724.223:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=927 comm="apparmor_parser" [26.559166] type=1400 audit(1338241724.223:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=928 comm="apparmor_parser" [26.559574] type=1400 audit(1338241724.223:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=928 comm="apparmor_parser" [26.575519] type=1400 audit(1338241724.239:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=931 comm="apparmor_parser" [26.581100] type=1400 audit(1338241724.247:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=931 comm="apparmor_parser" [26.582794] type=1400 audit(1338241724.247:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=929 comm="apparmor_parser" [26.605672] ppdev: user-space parallel port driver [27.592475] sky2 0000:09:00.0: eth0: enabling interface [27.604329] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.606962] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.852509] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [27.852513] vesafb: scrolling: redraw [27.852515] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [27.852523] mtrr: type mismatch for e0000000,400000 old: write-back new: write-combining [27.852527] mtrr: type mismatch for e0000000,200000 old: write-back new: write-combining [27.852531] mtrr: type mismatch for e0000000,100000 old: write-back new: write-combining [27.852534] mtrr: type mismatch for e0000000,80000 old: write-back new: write-combining [27.852538] mtrr: type mismatch for e0000000,40000 old: write-back new: write-combining [27.852541] mtrr: type mismatch for e0000000,20000 old: write-back new: write-combining [27.852544] mtrr: type mismatch for e0000000,10000 old: write-back new: write-combining [27.852548] mtrr: type mismatch for e0000000,8000 old: write-back new: write-combining [27.852551] mtrr: type mismatch for e0000000,4000 old: write-back new: write-combining [27.852554] mtrr: type mismatch for e0000000,2000 old: write-back new: write-combining [27.852558] mtrr: type mismatch for e0000000,1000 old: write-back new: write-combining [27.853154] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90005580000, using 3072k, total 3072k [27.853405] Console: switching to colour frame buffer device 128x48 [27.853426] fb0: VESA VGA frame buffer device [28.539800] fglrx_pci 0000:01:00.0: irq 48 for MSI/MSI-X [28.540552] [fglrx] Firegl kernel thread PID: 1168 [28.540679] [fglrx] Firegl kernel thread PID: 1169 [28.540789] [fglrx] Firegl kernel thread PID: 1170 [28.540932] [fglrx] IRQ 48 Enabled [29.845620] [fglrx] Gart USWC size:1236 M. [29.845624] [fglrx] Gart cacheable size:489 M. [29.845629] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [29.845632] [fglrx] Reserved FB block: Unshared offset:fc21000, size:3df000 [29.845635] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [59.700023] eth2: no IPv6 routers present

  Read the article

• Killing Stuck Child JVM's

  - by ACShorten

  Note: This facility only applies to Oracle Utilities Application Framework products using COBOL. In some situations, the Child JVM's may spin. This causes multiple startup/shutdown Child JVM messages to be displayed and recursive child JVM's to be initiated and shunned. If the following: Unable to establish connection on port …. after waiting .. seconds.The issue can be caused intermittently by CPU spins in connection to the creation of new processes, specifically Child JVMs. Recursive (or double) invocation of the System.exit call in the remote JVM may be caused by a Process.destroy call that the parent JVM always issues when shunning a JVM. The issue may happen when the thread in the parent JVM that is responsible for the recycling gets stuck and it affects all child JVMs. If this issue occurs at your site then there are a number of options to address the issue: Configure an Operating System level kill command to force the Child JVM to be shunned when it becomes stuck. Configure a Process.destroy command to be used if the kill command is not configured or desired. Specify a time tolerance to detect stuck threads before issuing the Process.destroy or kill commands. Note: This facility is also used when the Parent JVM is also shutdown to ensure no zombie Child JVM's exit. The following additional settings must be added to the spl.properties for the Business Application Server to use this facility: spl.runtime.cobol.remote.kill.command – Specify the command to kill the Child JVM process. This can be a command or specify a script to execute to provide additional information. The kill.command property can accept two arguments, {pid} and {jvmNumber}, in the specified string. The arguments must be enclosed in curly braces as shown here. Note: The PID will be appended to the killcmd string, unless the {pid} and {jvmNumber} arguments are specified. The jvmNumber can be useful if passed to a script for logging purposes. Note: If a script is used it must be in the path and be executable by the OS user running the system. spl.runtime.cobol.remote.destroy.enabled – Specify whether to use the Process.destroy command instead of the kill command. Specify true or false. Default value is false. Note: Unless otherwise required, it is recommended to use the kill command option if shunning JVM's is an issue. There this value can remain its default value, false, unless otherwise required. spl.runtime.cobol.remote.kill.delaysecs – Specify the number of seconds to wait for the Child JVM to terminate naturally before issuing the Process.destroy or kill commands. Default is 10 seconds. For example: spl.runtime.cobol.remote.kill.command=kill -9 {pid} {jvmNumber}spl.runtime.cobol.remote.destroy.enabled=falsespl.runtime.cobol.remote.kill.delaysecs=10 When a Child JVM is to be recycled, these properties are inspected and the spl.runtime.cobol.remote.kill.command, executed if provided. This is done after waiting for spl.runtime.cobol.remote.kill.delaysecs seconds to give the JVM time to shut itself down. The spl.runtime.cobol.remote.destroy.enabled property must be set to true AND the spl.runtime.cobol.remote.kill.command omitted for the original Process.destroy command to be used on the process. Note: By default the spl.runtime.cobol.remote.destroy enabled is set to false and is therefore disabled. If neither spl.runtime.cobol.remote.kill.command nor spl.runtime.cobol.remote.destroy.enabled is specified, child JVMs will not beforcibly killed. They will be left to shut themselves down (which may lead to orphan JVMs). If both are specified, the spl.runtime.cobol.remote.kill.command is preferred and spl.runtime.cobol.remote.destroy.enabled defaulted to false.It is recommended to invoke a script to issue the direct kill command instead of directly using the kill -9 commands.For example, the following sample script ensures that the process Id is an active cobjrun process before issuing the kill command: forcequit.sh #!/bin/shTHETIME=`date +"%Y-%m-%d %H:%M:%S"`if [ "$1" = "" ]then  echo "$THETIME: Process Id is required" >>$SPLSYSTEMLOGS/forcequit.log  exit 1fijavaexec=cobjrunps e $1 | grep -c $javaexecif [ $? = 0 ]then  echo "$THETIME: Process $1 is an active $javaexec process -- issuing kill-9 $1" >>$SPLSYSTEMLOGS/forcequit.log  kill -9 $1exit 0else  echo "$THETIME: Process id $1 is not a $javaexec process or not active --  kill will not be issued" >>$SPLSYSTEMLOGS/forcequit.logexit 1fi This script's name would then be specified as the value for the spl.runtime.cobol.remote.kill.command property, for example: spl.runtime.cobol.remote.kill.command=forcequit.sh The forcequit script does not have any explicit parameters but pid is passed automatically. To use the jvmNumber parameter it must explicitly specified in the command. For example, to call script forcequit.sh and pass it the pid and the child JVM number, specify it as follows: spl.runtime.cobol.remote.kill.command=forcequit.sh {pid} {jvmNumber} The script can then use the JVM number for logging purposes or to further ensure that the correct pid is being killed.If the arguments are omitted, the pid is automatically appended to the spl.runtime.cobol.remote.kill.command string. To use this facility the following patches must be installed: Patch 13719584 for Oracle Utilities Application Framework V2.1, Patches 13684595 and 13634933 for Oracle Utilities Application Framework V2.2 Group Fix 4 (as Patch 13640668) for Oracle Utilities Application Framework V4.1.

  Read the article

• BIND9 server not responding to external queries

  - by Twitchy

  I have set up a BIND server on my dedicated box which I want to host a nameserver for my domain on. When I use dig @202.169.196.59 nzserver.co.nz locally on the server I get the following response... ; <<>> DiG 9.8.1-P1 <<>> @202.169.196.59 nzserver.co.nz ; (1 server found) ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 43773 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 2 ;; QUESTION SECTION: ;nzserver.co.nz. IN A ;; ANSWER SECTION: nzserver.co.nz. 3600 IN A 202.169.196.59 ;; AUTHORITY SECTION: nzserver.co.nz. 3600 IN NS ns2.nzserver.co.nz. nzserver.co.nz. 3600 IN NS ns1.nzserver.co.nz. ;; ADDITIONAL SECTION: ns1.nzserver.co.nz. 3600 IN A 202.169.196.59 ns2.nzserver.co.nz. 3600 IN A 202.169.196.59 ;; Query time: 0 msec ;; SERVER: 202.169.196.59#53(202.169.196.59) ;; WHEN: Sat Oct 27 15:40:45 2012 ;; MSG SIZE rcvd: 116 Which is good, and is the output I want. But when simply using dig nzserver.co.nz I get... ; <<>> DiG 9.8.1-P1 <<>> nzserver.co.nz ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 16970 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;nzserver.co.nz. IN A ;; Query time: 308 msec ;; SERVER: 202.169.192.61#53(202.169.192.61) ;; WHEN: Sat Oct 27 17:09:12 2012 ;; MSG SIZE rcvd: 32 And if I use dig @202.169.196.59 nzserver.co.nz on another linux machine I get... ; <<>> DiG 9.7.3 <<>> @202.169.196.59 nzserver.co.nz ; (1 server found) ;; global options: +cmd ;; connection timed out; no servers could be reached Am I doing something wrong here? Port 53 is definitely open. /etc/bind/named.conf.options options { directory "/var/cache/bind"; forwarders { 202.169.192.61; 202.169.206.10; }; listen-on { 202.169.196.59; }; }; /etc/bind/named.conf.local zone "nzserver.co.nz" { type master; file "/etc/bind/nzserver.co.nz.zone"; }; /etc/bind/nzserver.co.nz.zone ; BIND db file for nzserver.co.nz $ORIGIN nzserver.co.nz. @ IN SOA ns1.nzserver.co.nz. mr.steven.french.gmail.com. ( 2012102606 28800 7200 864000 3600 ) NS ns1.nzserver.co.nz. NS ns2.nzserver.co.nz. MX 10 mail.nzserver.co.nz. @ IN A 202.169.196.59 * IN A 202.169.196.59 ns1 IN A 202.169.196.59 ns2 IN A 202.169.196.59 www IN A 202.169.196.59 mail IN A 202.169.196.59

  Read the article

• OS Analytics with Oracle Enterprise Manager (by Eran Steiner)

  - by Zeynep Koch

  Oracle Enterprise Manager Ops Center provides a feature called "OS Analytics". This feature allows you to get a better understanding of how the Operating System is being utilized. You can research the historical usage as well as real time data. This post will show how you can benefit from OS Analytics and how it works behind the scenes. The recording of our call to discuss this blog is available here: https://oracleconferencing.webex.com/oracleconferencing/ldr.php?AT=pb&SP=MC&rID=71517797&rKey=4ec9d4a3508564b3Download the presentation here See also: Blog about Alert Monitoring and Problem Notification Blog about Using Operational Profiles to Install Packages and other content Here is quick summary of what you can do with OS Analytics in Ops Center: View historical charts and real time value of CPU, memory, network and disk utilization Find the top CPU and Memory processes in real time or at a certain historical day Determine proper monitoring thresholds based on historical data Drill down into a process details Where to start To start with OS Analytics, choose the OS asset in the tree and click the Analytics tab. You can see the CPU utilization, Memory utilization and Network utilization, along with the current real time top 5 processes in each category (click the image to see a larger version):  In the above screen, you can click each of the top 5 processes to see a more detailed view of that process. Here is an example of one of the processes: One of the cool things is that you can see the process tree for this process along with some port binding and open file descriptors. Next, click the "Processes" tab to see real time information of all the processes on the machine: An interesting column is the "Target" column. If you configured Ops Center to work with Enterprise Manager Cloud Control, then the two products will talk to each other and Ops Center will display the correlated target from Cloud Control in this table. If you are only using Ops Center - this column will remain empty. The "Threshold" tab is particularly helpful - you can view historical trends of different monitored values and based on the graph - determine what the monitoring values should be: You can ask Ops Center to suggest monitoring levels based on the historical values or you can set your own. The different colors in the graph represent the current set levels: Red for critical, Yellow for warning and Blue for Information, allowing you to quickly see how they're positioned against real data. It's important to note that when looking at longer periods, Ops Center smooths out the data and uses averages. So when looking at values such as CPU Usage, try shorter time frames which are more detailed, such as one hour or one day. Applying new monitoring values When first applying new values to monitored attributes - a popup will come up asking if it's OK to get you out of the current Monitoring Policy. This is OK if you want to either have custom monitoring for a specific machine, or if you want to use this current machine as a "Gold image" and extract a Monitoring Policy from it. You can later apply the new Monitoring Policy to other machines and also set it as a default Monitoring Profile. Once you're done with applying the different monitoring values, you can review and change them in the "Monitoring" tab. You can also click the "Extract a Monitoring Policy" in the actions pane on the right to save all the new values to a new Monitoring Policy, which can then be found under "Plan Management" -> "Monitoring Policies". Visiting the past Under the "History" tab you can "go back in time". This is very helpful when you know that a machine was busy a few hours ago (perhaps in the middle of the night?), but you were not around to take a look at it in real time. Here's a view into yesterday's data on one of the machines: You can see an interesting CPU spike happening at around 3:30 am along with some memory use. In the bottom table you can see the top 5 CPU and Memory consumers at the requested time. Very quickly you can see that this spike is related to the Solaris 11 IPS repository synchronization process using the "pkgrecv" command. The "time machine" doesn't stop here - you can also view historical data to determine which of the zones was the busiest at a given time: Under the hood The data collected is stored on each of the agents under /var/opt/sun/xvm/analytics/historical/ An "os.zip" file exists for the main OS. Inside you will find many small text files, named after the Epoch time stamp in which they were taken If you have any zones, there will be a file called "guests.zip" containing the same small files for all the zones, as well as a folder with the name of the zone along with "os.zip" in it If this is the Enterprise Controller or the Proxy Controller, you will have folders called "proxy" and "sat" in which you will find the "os.zip" for that controller The actual script collecting the data can be viewed for debugging purposes as well: On Linux, the location is: /opt/sun/xvmoc/private/os_analytics/collect If you would like to redirect all the standard error into a file for debugging, touch the following file and the output will go into it: # touch /tmp/.collect.stderr   The temporary data is collected under /var/opt/sun/xvm/analytics/.collectdb until it is zipped. If you would like to review the properties for the Analytics, you can view those per each agent in /opt/sun/n1gc/lib/XVM.properties. Find the section "Analytics configurable properties for OS and VSC" to view the Analytics specific values. I hope you find this helpful! Please post questions in the comments below. Eran Steiner

  Read the article

• Searching for the Perfect Developer&rsquo;s Laptop.

  - by mbcrump

  I have been in the market for a new computer for several months. I set out with a budget of around $1200. I knew up front that the machine would be used for developing applications and maybe some light gaming. I kept switching between buying a laptop or a desktop but the laptop won because: With a Laptop, I can carry it everywhere and with a desktop I can’t. I searched for about 2 weeks and narrowed it down to a list of must-have’s : i7 Processor (I wasn’t going to settle for an i5 or AMD. I wanted a true Quad-core machine, not 2 dual-core fused together). 15.6” monitor SSD 128GB or Larger. – It’s almost 2011 and I don’t want an old standard HDD in this machine. 8GB of DDR3 Ram. – The more the better, right? 1GB Video Card (Prefer NVidia) – I might want to play games with this. HDMI Port – Almost a standard on new Machines. This would be used when I am on the road and want to stream Netflix to the HDTV in the Hotel room. Webcam Built-in – This would be to video chat with the wife and kids if I am on the road. 6-Cell Battery. – I’ve read that an i7 in a laptop really kills the battery. A 6-cell or 9-cell is even better. That is a pretty long list for a budget of around $1200. I searched around the internet and could not buy this machine prebuilt for under $1200. That was even with coupons and my company’s 10% Dell discount. The only way that I would get a machine like this was to buy a prebuilt and replace parts. I chose the  Lenovo Y560 on Newegg to start as my base. Below is a top-down picture of it.   Part 1: The Hardware The Specs for this machine: Color :  GrayOperating System : Windows 7 Home Premium 64-bitCPU Type : Intel Core i7-740QM(1.73GHz)Screen : 15.6" WXGAMemory Size : 4GB DDR3Hard Disk : 500GBOptical Drive : DVD±R/RWGraphics Card : ATI Mobility Radeon HD 5730Video Memory : 1GBCommunication : Gigabit LAN and WLANCard slot : 1 x Express Card/34Battery Life : Up to 3.5 hoursDimensions : 15.20" x 10.00" x 0.80" - 1.30"Weight : 5.95 lbs. This computer met most of the requirements above except that it didn’t come with an SSD or have 8GB of DDR3 Memory. So, I needed to start shopping except this time for an SSD. I asked around on twitter and other hardware forums and everyone pointed me to the Crucial C300 SSD. After checking prices of the drive, it was going to cost an extra $275 bucks and I was going from a spacious 500GB drive to 128GB. After watching some of the SSD videos on YouTube I started feeling better. Below is a pic of the Crucial C300 SSD. The second thing that I needed to upgrade was the RAM. It came with 4GB of DDR3 RAM, but it was slow. I decided to buy the Crucial 8GB (4GB x 2) Kit from Newegg. This RAM cost an extra $120 and had a CAS Latency of 7. In the end this machine delivered everything that I wanted and it cost around $1300. You are probably saying, well your budget was $1200. I have spare parts that I’m planning on selling on eBay or Anandtech.  =) If you are interested then shoot me an email and I will give you a great deal mbcrump[at]gmail[dot]com. 500GB Laptop 7200RPM HDD 4GB of DDR3 RAM (2GB x 2) faceVision HD 720p Camera – Unopened In the end my Windows Experience Rating of the SSD was 7.7 and the CPU 7.1. The max that you can get is a 7.9. Part 2: The Software I’m very lucky that I get a lot of software for free. When choosing a laptop, the OS really doesn’t matter because I would never keep the bloatware pre-installed or Windows 7 Home Premium on my main development machine. Matter of fact, as soon as I got the laptop, I immediately took out the old HDD without booting into it. After I got the SSD into the machine, I installed Windows 7 Ultimate 64-Bit. The BIOS was out of date, so I updated that to the latest version and started downloading drivers off of Lenovo’s site. I had to download the Wireless Networking Drivers to a USB-Key before I could get my machine on my wireless network. I also discovered that if the date on your computer is off then you cannot join the Windows 7 Homegroup until you fix it. I’m aware that most people like peeking into what programs other software developers use and I went ahead and listed my “essentials” of a fresh build. I am a big Silverlight guy, so naturally some of the software listed below is specific to Silverlight. You should also check out my master list of Tools and Utilities for the .NET Developer. See a killer app that I’m missing? Feel free to leave it in the comments below. My Software Essential List. CPU-Z Dropbox Everything Search Tool Expression Encoder Update Expression Studio 4 Ultimate Foxit Reader Google Chrome Infragistics NetAdvantage Ultimate Edition Keepass Microsoft Office Professional Plus 2010 Microsoft Security Essentials 2  Mindscape Silverlight Elements Notepad 2 (with shell extension) Precode Code Snippet Manager RealVNC Reflector ReSharper v5.1.1753.4 Silverlight 4 Toolkit Silverlight Spy Snagit 10 SyncFusion Reporting Controls for Silverlight Telerik Silverlight RadControls TweetDeck Virtual Clone Drive Visual Studio 2010 Feature Pack 2 Visual Studio 2010 Ultimate VS KB2403277 Update to get Feature Pack 2 to work. Windows 7 Ultimate 64-Bit Windows Live Essentials 2011 Windows Live Writer Backup. Windows Phone Development Tools That is pretty much it, I have a new laptop and am happy with the purchase. If you have any questions then feel free to leave a comment below.  Subscribe to my feed

  Read the article

• Surface and the Uphill Battle to Win Over iPad Users (Namely: Me)

  - by D'Arcy Lussier

  I went away this past weekend and decided to bring along the Windows 8 tablet from the Build conference last year – y’know, to give Windows 8 a try in a typical scenario. I also brought our iPad 2 along since I figured my wife would want to use that. I’d love to tell you how I found using my Windows 8 tablet but I can’t – I used the iPad exclusively the entire weekend. It was during this that I realized what Microsoft needs to do to win me over as an iPad user. As you’ll see, I’m left wondering what it is that Surface is meant to compete with: iPad and other tablets, or thin laptops like the MacBook Air or Ultrabooks. Device Size I really like the size of the iPad compared with the Build tablet. It’s not as long and the thinness/weight of the device makes it feel more like you’re holding a magazine than a computer. I’m pleased that Microsoft will be matching the thinness of the iPad with Surface, but I’m suspect as to what that actually means. The iPad’s edges slant inwards where the Surface has a thicker boxish look (similar to the iPhone 4S). So while they may have the same depth at the deepest part of both devices, I bet the iPad will come off feeling thinner. However, its not lost on me the number of external port options the Surface’s design provides over the iPad (Usb, etc.). With that said, I haven’t missed having a USB slot on my iPad. I’m not a fan of lengthening the Surface screen size to almost a full inch over the iPad, mainly because… Vertical Orientation Experience Did you notice at the announce event, in the images of the devices that have been released, and in any marketing for it, that the surface is always displayed in horizontal orientation. This is a huge beef I have with my Build tablet and why I prefer the iPad. Yes the iPad can do the wide-screenish mode, but the iPad is oriented to be vertical by nature. Don’t agree? Look at the button and camera placement – both on the shorter sides of the device. Compare that with the Surface, where the orientation for the button and camera is on the longer sides. To be fair, Blackberry and the horde of Android tablets out there haven’t gotten this either – since most monitors are widescreen nowadays tablets should be too right? Wrong. Widescreen is great for certain things, but tasks such as reading is not one of them – hence why monitor companies like Dell provide stands that allow you to flip your widescreen monitor to a vertical orientation. That Microsoft has chosen a horizontal orientation by default for Windows 8 is disappointing – hopefully hardware manufacturers will be given the option of a default vertical orientation. Fast Startup Time I like that I can turn off/turn on the iPad very quickly. Even from a true “off” mode and not just sleeping, the iPad boots up very quickly. Windows RT needs to have that same quick response. If I start finding that I’m waiting for the device to boot up for more than 30 seconds that could be a show stopper. No Heat I really hate that the Build tablet has fans that kick in to cool the procs, but its basically a slate computer and I get its part of that prototype build. For Surface, it needs to be the same type of experience as the iPad – no heat! I know Surface doesn’t have fans and uses some cool new vent system or something like that, but even then – I want to sit and read a book on my Surface without having to feel any heat coming from the device, which is the experience I have with the iPad now. What About Apps?! I am definitely not the target client when it comes to app stores. On my iPad I use: Safari Kindle Reader Twitter App Settlers of Catan TSN’s App And that’s it. So really, while its nice that some version of Office might be available, I’m not planning on utilizing a Surface for creating a PowerPoint or working on a Word document – that’s what my laptop is for. I want my tablet to be for information snacking or as an e-reader and occasionally an entertainment device. Surface vs iPad or Surface vs Air? The more that I read up on Surface, the more I wonder if it won’t be a touch-enabled MacBook Air competitor more than an iPad one. Also, I really question if Microsoft gets tablets – when one of your main selling features is a built-in physical keyboard it speaks more to a traditional laptop experience than a tablet one that’s entirely reliant on touch. Still, I really love the Windows Phone interface – way more than iOS – so I’m still very optimistic that the Metro experience on the tablet will be fantastic. I just worry that Microsoft has interpreted a tablet as a computer with a removable keyboard and a touch screen, and that’s not what tablet computing is about at all.

  Read the article

• Better documentation for tasks waiting on resources

  - by SQLOS Team

  The sys.dm_os_waiting_tasks DMV contains a wealth of useful information about tasks waiting on a resource, but until now detailed information about the resource being consumed - sys.dm_os_waiting_tasks.resource_description - hasn't been documented, apart from a rather self-evident "Description of the resource that is being consumed."   Thanks to a recent Connect suggestion this column will get more information added. Here is a summary of the possible values that can appear in this column - Note this information is current for SQL Server 2008 R2 and Denali:   Thread-pool resource owner:•       threadpool id=scheduler<hex-address> Parallel query resource owner:•       exchangeEvent id={Port|Pipe}<hex-address> WaitType=<exchange-wait-type> nodeId=<exchange-node-id> Exchange-wait-type can be one of the following.•       e_waitNone•       e_waitPipeNewRow•       e_waitPipeGetRow•       e_waitSynchronizeConsumerOpen•       e_waitPortOpen•       e_waitPortClose•       e_waitRange Lock resource owner:<type-specific-description> id=lock<lock-hex-address> mode=<mode> associatedObjectId=<associated-obj-id>               <type-specific-description> can be:• For DATABASE: databaselock subresource=<databaselock-subresource> dbid=<db-id>• For FILE: filelock fileid=<file-id> subresource=<filelock-subresource> dbid=<db-id>• For OBJECT: objectlock lockPartition=<lock-partition-id> objid=<obj-id> subresource=<objectlock-subresource> dbid=<db-id>• For PAGE: pagelock fileid=<file-id> pageid=<page-id> dbid=<db-id> subresource=<pagelock-subresource>• For Key: keylock  hobtid=<hobt-id> dbid=<db-id>• For EXTENT: extentlock fileid=<file-id> pageid=<page-id> dbid=<db-id>• For RID: ridlock fileid=<file-id> pageid=<page-id> dbid=<db-id>• For APPLICATION: applicationlock hash=<hash> databasePrincipalId=<role-id> dbid=<db-id>• For METADATA: metadatalock subresource=<metadata-subresource> classid=<metadatalock-description> dbid=<db-id>• For HOBT: hobtlock hobtid=<hobt-id> subresource=<hobt-subresource> dbid=<db-id>• For ALLOCATION_UNIT: allocunitlock hobtid=<hobt-id> subresource=<alloc-unit-subresource> dbid=<db-id> <mode> can be:• Sch-S• Sch-M• S• U• X• IS• IU• IX• SIU• SIX• UIX• BU• RangeS-S• RangeS-U• RangeI-N• RangeI-S• RangeI-U• RangeI-X• RangeX-S• RangeX-U• RangeX-X External resource owner:•       External ExternalResource=<wait-type> Generic resource owner:•       TransactionMutex TransactionInfo Workspace=<workspace-id>•       Mutex•       CLRTaskJoin•       CLRMonitorEvent•       CLRRWLockEvent•       resourceWait Latch resource owner:•       <db-id>:<file-id>:<page-in-file>•       <GUID>•       <latch-class> (<latch-address>)   Further Information Slava Oks's weblog: sys.dm_os_waiting_tasks.Informit.com: Identifying Blocking Using sys.dm_os_waiting_tasks - Ken Henderson   - Guy

  Read the article

• Keep it Professional &ndash; Multiple Environments

  - by AjarnMark

  I have certainly been reading blogs a whole lot more than writing them the last several weeks, and it’s about time I got back to writing.  I have been collecting several topics and references for blog posts…some of which will probably just never get written as the timeliness of the topics fade over time.  Nonetheless, I’m back, and I think it is time to revive my Doing Business Right series, this time coming from the slant of managing a development team rather than the previous angle of being self-employed.  First up: separating Dev, Test, and Prod. A few months ago, Colin Stasiuk (@BenchmarkIT) wrote a great post about separating your Dev, Test/UAT, and Prod environments.  This post covers all the important points such as removing Developer access from both PROD and UAT, and the importance of proper deployment (a.k.a. promotion) procedures.  I won’t repeat it all here, go read the original!  But what I do want to address is what I believe to be the #1 excuse people use for not having separate environments:  Money.  I discussed this briefly in my comment on Colin’s post at the time, but let me repeat it here and expand on it a bit. Don’t let the size of your company or the size of its budget dictate whether you do things professionally or not.  I am convinced that most developers and development teams would agree that it is a best practice to have separate environments for development, testing, and production (a.k.a. Live).  So why don’t they?  Because they think that it means separate servers which means more money.  While having separate physical servers for the different environments would be ideal, it is not an absolute requirement in order to make this work.  Here are a few ideas: Use multiple instances of SQL Server and multiple Web Sites with Headers or Ports.  For no additional fees* you can install multiple instances of SQL Server on the same machine.  This gives you a nice separation, allowing you to even use the same database names as will appear in PROD, yet isolating the data and security access.  And in IIS, you can create multiple Web Sites on the same server just by using Host Headers or different port numbers to separate them.  This approach does still pose the risk of non-Prod environments impacting performance on Prod, but when your application is busy enough for that to be a concern, you can probably afford one of the other options. Use desktop PCs instead of servers.  Instead of investing in full server-grade hardware, you can mimic the separate environments on old desktop PCs and at least get functional equivalency, if not performance matching.  The last I checked, Microsoft did not require separate licensing for SQL Server if that installation was used exclusively for dev or test purposes*.  There may be some version or performance differences between this approach and what you have in Prod, but you have isolated test from impacting Prod resources this way. Virtualization.  This is of course one of the hot topics of the day, and I would be remiss if I did not suggest this.  It is quite easy these days to setup virtual machines so that, again, your environments are fairly isolated from one another, and you retain all the security and procedural benefits of having separate environments. So the point is, keep your high professional standards intact.  You don’t need to compromise on using proper procedure just because you work in a small company with a small budget.  Keep doing things the right way! By the way, where I work, our DEV environment is not on a server.  All development is done on the developer’s individual workstation where it can be isolated from other developers’ work for the duration of writing the code, but also where the developers have to reconcile (merge) differences in code under concurrent development.  This usually means that each change is executed multiple times (once per developer to update their environments with the latest changes from others) giving us an extra, informal. test deployment before even going to the Test/UAT server.  It also means that if the network goes down, the developers can continue to hum along because they are not dependent on networked resources.  In fact, they will likely be even more productive because they aren’t being interrupted by email…but that’s another post I need to write. * I am not a lawyer, nor a licensing specialist, but it appeared to be so the last time I checked.  When in doubt, consult an expert on the topic.

  Read the article

• I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

  - by user69670

  Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

  Read the article

• BIP and Mapviewer Mash Up I

  - by Tim Dexter

  I was out in Yellowstone last week soaking up various wildlife and a bit too much rain ... good to be back until the 95F heat yesterday. Taking a little break from the Excel templates; the dev folks are planing an Excel patch in the next week or so that will add a mass of new functionality. At the risk of completely mis leading you I'm going to hang back a while. What I have written so far holds true and will continue to do so. This week, I have been mostly eating 'mapviewer' ... answers on a post card please, TV show and character. I had a request to show how BIP can call mapviewer and render a dynamic map in an output. So I hit the books and colleagues for some answers. Mapviewer is Oracle's geographic information system, hereby known as GIS. I use it a lot in our BIEE demos where the interaction with the maps is very impressive. Need a map of California and its congressional districts? I have contacts; Jerry and David with their little black box of maps. Once in my possession I can build highly interactive, clickable maps that allow the user to drill into more information using a very friendly interface driving BIEE content and navigation. But what about maps in BIP output? Bryan Wise, who has written some articles on this blog did some work a while back with the PL/SQL API interface. The extract for the report called a function that in turn called the mapviewer server, passing a set of mapping requirements, it then returned a URL to a cached copy of that map. Easy to then have BIP render that image. Thats still very doable. You need to install a couple of packages and then load the mapviewer java APIs into the database. Then you can write your function to the APIs. A little involved? Maybe, but the database is doing all the heavy lifting for you. I thought I would investigate another method for getting the maps back into BIP. There is a URL interface you can call, this involves building an XML message to be passed to the mapviewer server. It's pretty straightforward to use on the mapviewer side. On the BIP side things are little more tricksy. After some unexpected messing about I finally got the ubiquitous Hello World map to render using the URL method. Not the most exciting map in the world, lots of ocean and a rather long URL to get it to render. http://127.0.0.1:9704/mapviewer/omserver?xml_request=%3Cmap_request%20title=%22Hello%20World%22%20datasource=%22cagis%22%20format=%22GIF_STREAM%22/%3E Notice all of the encoding in the URL string to handle the spaces, quotes, etc. All necessary to get BIP to make the call to the mapviewer server correctly without truncating the URL if it hits a real space rather than a %20. With that in mind constructing the URL was pretty simple. I'm not going to get into the content of the URL too much, for that you need to bone up on the mapviewer XML API. Check out the home page here and the documentation here. To make the template portable I used the standard CURRENT_SERVER_URL parameter from the BIP server and declared that in my template. <?param@begin:CURRENT_SERVER_URL;'myserver'?> Ignore the 'myserver', that was just a dummy value for testing at runtime it will resolve to: 'http://yourserver:port/xmlpserver' Not quite what we need as mapviewer has its own server path, in my case I needed 'mapviewer/omserver?xml_request=' as the fixed path to the mapviewer request URL. A little concatenation and substringing later I came up with <?param@begin:mURL;concat(substring($CURRENT_SERVER_URL,1,22),'mapviewer/omserver?xml_request=')?> Thats the basic URL that I can then build on. To get the Hello World map I need to add the following: <map_request title="Hello World" datasource="cagis" format="GIF_STREAM"/> Those angle brackets were the source of my headache, BIPs XSLT engine was attempting to process them rather than just pass them. Hok Min to the rescue ... again. I owe him lunch when I get out to HQ again! To solve the problem, I needed to escape all the characters and white space and then use native XSL to assign the string to a parameter. <xsl:param xdofo:ctx="begin"name="pXML">%3Cmap_request%20title=%22Hello%20World%22 %20datasource=%22cagis%22%20format=%22GIF_STREAM%22/%3E</xsl:param> I did not need to assign it to a parameter but I felt that if I were going to do anything more serious than Hello World like plotting points of interest on the map. I would need to dynamically build the URL, so using a set of parameters or variables that I then concatenated would be easier. Now I had the initial server string and the request all I then did was combine the two using a concat: concat($mURL,$pXML) Embedding that into an image tag: <fo:external-graphic src="url({concat($mURL,$pXML)})"/> and I was done. Notice the curly braces to get the concat evaluated prior to the image call. As you will see next time, building the XML message to go onto the URL can get quite complex but I have used it with some data. Ultimately, it would be easier to build an extension to BIP to handle the data to be plotted, it would then build the XML message, call mapviewer and return a URL to the map image for BIP to render. More on that next time ...

  Read the article

• Is this proper OO design for C++?

  - by user121917

  I recently took a software processes course and this is my first time attempting OO design on my own. I am trying to follow OO design principles and C++ conventions. I attempted and gave up on MVC for this application, but I am trying to "decouple" my classes such that they can be easily unit-tested and so that I can easily change the GUI library used and/or the target OS. At this time, I have finished designing classes but have not yet started implementing methods. The function of the software is to log all packets sent and received, and display them on the screen (like WireShark, but for one local process only). The software accomplishes this by hooking the send() and recv() functions in winsock32.dll, or some other pair of analogous functions depending on what the intended Target is. The hooks add packets to SendPacketList/RecvPacketList. The GuiLogic class starts a thread which checks for new packets. When new packets are found, it utilizes the PacketFilter class to determine the formatting for the new packet, and then sends it to MainWindow, a native win32 window (with intent to later port to Qt).1 Full size image of UML class diagram Here are my classes in skeleton/header form (this is my actual code): class PacketModel { protected: std::vector<byte> data; int id; public: PacketModel(); PacketModel(byte* data, unsigned int size); PacketModel(int id, byte* data, unsigned int size); int GetLen(); bool IsValid(); //len >= sizeof(opcode_t) opcode_t GetOpcode(); byte* GetData(); //returns &(data[0]) bool GetData(byte* outdata, int maxlen); void SetData(byte* pdata, int len); int GetId(); void SetId(int id); bool ParseData(char* instr); bool StringRepr(char* outstr); byte& operator[] (const int index); }; class SendPacket : public PacketModel { protected: byte* returnAddy; public: byte* GetReturnAddy(); void SetReturnAddy(byte* addy); }; class RecvPacket : public PacketModel { protected: byte* callAddy; public: byte* GetCallAddy(); void SetCallAddy(byte* addy); }; //problem: packets may be added to list at any time by any number of threads //solution: critical section associated with each packet list class Synch { public: void Enter(); void Leave(); }; template<class PacketType> class PacketList { private: static const int MAX_STORED_PACKETS = 1000; public: static const int DEFAULT_SHOWN_PACKETS = 100; private: vector<PacketType> list; Synch synch; //wrapper for critical section public: void AddPacket(PacketType* packet); PacketType* GetPacket(int id); int TotalPackets(); }; class SendPacketList : PacketList<SendPacket> { }; class RecvPacketList : PacketList<RecvPacket> { }; class Target //one socket { bool Send(SendPacket* packet); bool Inject(RecvPacket* packet); bool InitSendHook(SendPacketList* sendList); bool InitRecvHook(RecvPacketList* recvList); }; class FilterModel { private: opcode_t opcode; int colorID; bool bFilter; char name[41]; }; class FilterFile { private: FilterModel filter; public: void Save(); void Load(); FilterModel* GetFilter(opcode_t opcode); }; class PacketFilter { private: FilterFile filters; public: bool IsFiltered(opcode_t opcode); bool GetName(opcode_t opcode, char* namestr); //return false if name does not exist COLORREF GetColor(opcode_t opcode); //return default color if no custom color }; class GuiLogic { private: SendPacketList sendList; RecvPacketList recvList; PacketFilter packetFilter; void GetPacketRepr(PacketModel* packet); void ReadNew(); void AddToWindow(); public: void Refresh(); //called from thread void GetPacketInfo(int id); //called from MainWindow }; I'm looking for a general review of my OO design, use of UML, and use of C++ features. I especially just want to know if I'm doing anything considerably wrong. From what I've read, design review is on-topic for this site (and off-topic for the Code Review site). Any sort of feedback is greatly appreciated. Thanks for reading this.

  Read the article

• High Jinks, Hi Jacks, Exceptional DBA Awards and PASS

  - by Rodney

  The countdown to PASS has counted down.  The day after tomorrow I will board a plane, like many others, on my way for the 4th year in a row to SQL PASS Summit.  The anticipation has been excruciating but luckily I have this little thing called a day job as a DBA that has kept me busy and not thinking too much about the event. Well that is not exactly true since my beautiful wife works for PASS so we get to talk about SQL from the time we wake up until late in the evening. I would not have it any other way and I feel very fortunate to be a part of this great event and to have been chosen as the Exceptional DBA Award judge also for the 4th year in a row.  This year, I will have been again tasked with presenting the award to the winner, Mr. Jeff Moden and it will be a true honor to meet him in person as I have read many of his articles on SSC and have attended his session at PASS previously.  The speech is all ready but one item remains, which will be a surprise to all who attend the party on Tuesday night in Seattle (see links below).  Let's face it, Exceptional DBAs everywhere work very hard protecting our data stores, tuning queries, mentoring, saving money, installing clusters, etc and once in a while there is time to be exceptionally non-professional and have a bit of fun. Once incident that happened this year that falls under the High Jinks category was when my network admin asked if I could Telnet into a SQL instance and see if I could make the connection through the firewall that he had just configured. I was able to establish a connection on port 1433 and it occurred to me that it would be very interesting if I could actually run T-SQL queries via a Telnet session much like you might do with an SMTP server. With that thought, I proceeded to demonstrate this could be possible by convincing my senior DBA Shawn McGehee that I was able to do so. At first he did not believe me. It shook his world view.  It was inconceivable.  What I had done, behind the scenes, of course, was to copy and rename SQLCMD.exe to Telnet.exe and used it to connect and run a simple, "Select * from sys.databases" on the SQL instance. I think if it had been anyone other than Shawn I could have extended this ruse indefinitely but he caught on within 30 seconds. It was a fun thirty seconds though. On the High Jacks side of the house, which is really merged to be SQL HACKS, I finally, after several years of struggling with how to connect to an untrusted domain like in a DMZ with a windows account in SSMS, I stumbled upon a solution that does away with the requirement to use SQL Authentication.  While "Runas" is a great command to use to run an application with a higher privileged account, I had not previously been able to figure out how to connect to the remote domain with SSMS and "Runsas". It never connected and caused a login failure every time for the remote windows domain account. Then I ran across an option for "Runas",   "/netonly".  This option postpones the login until a connection is made and only then passes the remote login you supply when you first launch SSMS with the "Runas" command. So a typical shortcut would look like: "C:\Windows\System32\runas.exe /netonly /user:remotedomain.com\rodlandrum "C:\Program Files\Microsoft SQL Server\100\Tools\Binn\VSShell\Common7\IDE\Ssms.exe" You will want to make sure the passwords are synced between the two domains, your local domain and the remote domain, otherwise you may have account lockout issues, but I have found in weeks of testing this is a stable solution. Now it is time to get ready to head for Seattle. Please, if you see me (@SQLBeat) or my wife (@Karlakay22) please run up and high five me (wait..High Jinks.High Jacks.High Fives.Need to change the title) or give me a big bear hug if you are strong enough to lift me off the ground. And if you do actually do that, I will think you are awesome and will not embarrass you by crying out for help or complaining of a broken back or sciatic nerve damage. And now the links to others who have all of the details. First, for the MVP Deep Dives 2, of which, like John, I was lucky enough to be able to participate in this year. http://www.simple-talk.com/community/blogs/johnm/archive/2011/09/29/103577.aspx And the details of the SSC party where the Exceptional DBA of 2011, Jeff Moden, will be awarded. http://www.simple-talk.com/community/blogs/rebecca_amos/archive/2011/10/05/103661.aspx   Cheers! Rodney

  Read the article

• Cannot connect to secure wireless with Netgear wna3100 USB

  - by Vince Radice

  I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

  Read the article

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• Real-world SignalR example, ditching ghetto long polling

  - by Jeff

  One of the highlights of BUILD last week was the announcement that SignalR, a framework for real-time client to server (or cloud, if you will) communication, would be a real supported thing now with the weight of Microsoft behind it. Love the open source flava! If you aren’t familiar with SignalR, watch this BUILD session with PM Damian Edwards and dev David Fowler. Go ahead, I’ll wait. You’ll be in a happy place within the first ten minutes. If you skip to the end, you’ll see that they plan to ship this as a real first version by the end of the year. Insert slow clap here. Writing a few lines of code to move around a box from one browser to the next is a way cool demo, but how about something real-world? When learning new things, I find it difficult to be abstract, and I like real stuff. So I thought about what was in my tool box and the decided to port my crappy long-polling “there are new posts” feature of POP Forums to use SignalR. A few versions back, I added a feature where a button would light up while you were pecking out a reply if someone else made a post in the interim. It kind of saves you from that awkward moment where someone else posts some snark before you. While I was proud of the feature, I hated the implementation. When you clicked the reply button, it started polling an MVC URL asking if the last post you had matched the last one the server, and it did it every second and a half until you either replied or the server told you there was a new post, at which point it would display that button. The code was not glam: // in the reply setup PopForums.replyInterval = setInterval("PopForums.pollForNewPosts(" + topicID + ")", 1500); // called from the reply setup and the handler that fetches more posts PopForums.pollForNewPosts = function (topicID) { $.ajax({ url: PopForums.areaPath + "/Forum/IsLastPostInTopic/" + topicID, type: "GET", dataType: "text", data: "lastPostID=" + PopForums.currentTopicState.lastVisiblePost, success: function (result) { var lastPostLoaded = result.toLowerCase() == "true"; if (lastPostLoaded) { $("#MorePostsBeforeReplyButton").css("visibility", "hidden"); } else { $("#MorePostsBeforeReplyButton").css("visibility", "visible"); clearInterval(PopForums.replyInterval); } }, error: function () { } }); }; What’s going on here is the creation of an interval timer to keep calling the server and bugging it about new posts, and setting the visibility of a button appropriately. It looks like this if you’re monitoring requests in FireBug: Gross. The SignalR approach was to call a message broker when a reply was made, and have that broker call back to the listening clients, via a SingalR hub, to let them know about the new post. It seemed weird at first, but the server-side hub’s only method is to add the caller to a group, so new post notifications only go to callers viewing the topic where a new post was made. Beyond that, it’s important to remember that the hub is also the means to calling methods at the client end. Starting at the server side, here’s the hub: using Microsoft.AspNet.SignalR.Hubs; namespace PopForums.Messaging { public class Topics : Hub { public void ListenTo(int topicID) { Groups.Add(Context.ConnectionId, topicID.ToString()); } } } Have I mentioned how awesomely not complicated this is? The hub acts as the channel between the server and the client, and you’ll see how JavaScript calls the above method in a moment. Next, the broker class and its associated interface: using Microsoft.AspNet.SignalR; using Topic = PopForums.Models.Topic; namespace PopForums.Messaging { public interface IBroker { void NotifyNewPosts(Topic topic, int lasPostID); } public class Broker : IBroker { public void NotifyNewPosts(Topic topic, int lasPostID) { var context = GlobalHost.ConnectionManager.GetHubContext<Topics>(); context.Clients.Group(topic.TopicID.ToString()).notifyNewPosts(lasPostID); } } } The NotifyNewPosts method uses the static GlobalHost.ConnectionManager.GetHubContext<Topics>() method to get a reference to the hub, and then makes a call to clients in the group matched by the topic ID. It’s calling the notifyNewPosts method on the client. The TopicService class, which handles the reply data from the MVC controller, has an instance of the broker new’d up by dependency injection, so it took literally one line of code in the reply action method to get things moving. _broker.NotifyNewPosts(topic, post.PostID); The JavaScript side of things wasn’t much harder. When you click the reply button (or quote button), the reply window opens up and fires up a connection to the hub: var hub = $.connection.topics; hub.client.notifyNewPosts = function (lastPostID) { PopForums.setReplyMorePosts(lastPostID); }; $.connection.hub.start().done(function () { hub.server.listenTo(topicID); }); The important part to look at here is the creation of the notifyNewPosts function. That’s the method that is called from the server in the Broker class above. Conversely, once the connection is done, the script calls the listenTo method on the server, letting it know that this particular connection is listening for new posts on this specific topic ID. This whole experiment enables a lot of ideas that would make the forum more Facebook-like, letting you know when stuff is going on around you.

  Read the article

• Unexpected behaviour with glFramebufferTexture1D

  - by Roshan

  I am using render to texture concept with glFramebufferTexture1D. I am drawing a cube on non-default FBO with all the vertices as -1,1 (maximum) in X Y Z direction. Now i am setting viewport to X while rendering on non default FBO. My background is blue with white color of cube. For default FBO, i have created 1-D texture and attached this texture to above FBO with color attachment. I am setting width of texture equal to width*height of above FBO view-port. Now, when i render this texture to on another cube, i can see continuous white color on start or end of each face of the cube. That means part of the face is white and rest is blue. I am not sure whether this behavior is correct or not. I expect all the texels should be white as i am using -1 and 1 coordinates for cube rendered on non-default FBO. code: #define WIDTH 3 #define HEIGHT 3 GLfloat vertices8[]={ 1.0f,1.0f,1.0f, -1.0f,1.0f,1.0f, -1.0f,-1.0f,1.0f, 1.0f,-1.0f,1.0f,//face 1 1.0f,-1.0f,-1.0f, -1.0f,-1.0f,-1.0f, -1.0f,1.0f,-1.0f, 1.0f,1.0f,-1.0f,//face 2 1.0f,1.0f,1.0f, 1.0f,-1.0f,1.0f, 1.0f,-1.0f,-1.0f, 1.0f,1.0f,-1.0f,//face 3 -1.0f,1.0f,1.0f, -1.0f,1.0f,-1.0f, -1.0f,-1.0f,-1.0f, -1.0f,-1.0f,1.0f,//face 4 1.0f,1.0f,1.0f, 1.0f,1.0f,-1.0f, -1.0f,1.0f,-1.0f, -1.0f,1.0f,1.0f,//face 5 -1.0f,-1.0f,1.0f, -1.0f,-1.0f,-1.0f, 1.0f,-1.0f,-1.0f, 1.0f,-1.0f,1.0f//face 6 }; GLfloat vertices[]= { 0.5f,0.5f,0.5f, -0.5f,0.5f,0.5f, -0.5f,-0.5f,0.5f, 0.5f,-0.5f,0.5f,//face 1 0.5f,-0.5f,-0.5f, -0.5f,-0.5f,-0.5f, -0.5f,0.5f,-0.5f, 0.5f,0.5f,-0.5f,//face 2 0.5f,0.5f,0.5f, 0.5f,-0.5f,0.5f, 0.5f,-0.5f,-0.5f, 0.5f,0.5f,-0.5f,//face 3 -0.5f,0.5f,0.5f, -0.5f,0.5f,-0.5f, -0.5f,-0.5f,-0.5f, -0.5f,-0.5f,0.5f,//face 4 0.5f,0.5f,0.5f, 0.5f,0.5f,-0.5f, -0.5f,0.5f,-0.5f, -0.5f,0.5f,0.5f,//face 5 -0.5f,-0.5f,0.5f, -0.5f,-0.5f,-0.5f, 0.5f,-0.5f,-0.5f, 0.5f,-0.5f,0.5f//face 6 }; GLuint indices[] = { 0, 2, 1, 0, 3, 2, 4, 5, 6, 4, 6, 7, 8, 9, 10, 8, 10, 11, 12, 15, 14, 12, 14, 13, 16, 17, 18, 16, 18, 19, 20, 23, 22, 20, 22, 21 }; GLfloat texcoord[] = { 0.0, 0.0, 1.0, 0.0, 1.0, 1.0, 0.0, 1.0, 0.0, 0.0, 1.0, 0.0, 1.0, 1.0, 0.0, 1.0, 0.0, 0.0, 1.0, 0.0, 1.0, 1.0, 0.0, 1.0, 0.0, 0.0, 1.0, 0.0, 1.0, 1.0, 0.0, 1.0, 0.0, 0.0, 1.0, 0.0, 1.0, 1.0, 0.0, 1.0, 0.0, 0.0, 1.0, 0.0, 1.0, 1.0, 0.0, 1.0 }; glGenTextures(1, &id1); glBindTexture(GL_TEXTURE_1D, id1); glGenFramebuffers(1, &Fboid); glTexParameterf(GL_TEXTURE_1D, GL_TEXTURE_MIN_FILTER, GL_NEAREST); glTexParameterf(GL_TEXTURE_1D, GL_TEXTURE_MAG_FILTER, GL_NEAREST); glTexParameterf(GL_TEXTURE_1D, GL_TEXTURE_WRAP_S, GL_CLAMP_TO_EDGE); glTexImage1D(GL_TEXTURE_1D, 0, GL_RGBA, WIDTH*HEIGHT , 0, GL_RGBA, GL_UNSIGNED_BYTE,0); glBindFramebuffer(GL_FRAMEBUFFER, Fboid); glFramebufferTexture1D(GL_DRAW_FRAMEBUFFER,GL_COLOR_ATTACHMENT0,GL_TEXTURE_1D,id1,0); draw_cube(); glBindFramebuffer(GL_FRAMEBUFFER, 0); draw(); } draw_cube() { glViewport(0, 0, WIDTH, HEIGHT); glClearColor(0.0f, 0.0f, 0.5f, 1.0f); glClear(GL_COLOR_BUFFER_BIT); glEnableVertexAttribArray(glGetAttribLocation(temp.psId,"position")); glVertexAttribPointer(glGetAttribLocation(temp.psId,"position"), 3, GL_FLOAT, GL_FALSE, 0,vertices8); glDrawArrays (GL_TRIANGLE_FAN, 0, 24); } draw() { glClearColor(1.0f, 0.0f, 0.0f, 1.0f); glClearDepth(1.0f); glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); glEnableVertexAttribArray(glGetAttribLocation(shader_data.psId,"tk_position")); glVertexAttribPointer(glGetAttribLocation(shader_data.psId,"tk_position"), 3, GL_FLOAT, GL_FALSE, 0,vertices); nResult = GL_ERROR_CHECK((GL_NO_ERROR, "glVertexAttribPointer(position, 3, GL_FLOAT, GL_FALSE, 0,vertices);")); glEnableVertexAttribArray(glGetAttribLocation(shader_data.psId,"inputtexcoord")); glVertexAttribPointer(glGetAttribLocation(shader_data.psId,"inputtexcoord"), 2, GL_FLOAT, GL_FALSE, 0,texcoord); glBindTexture(*target11, id1); glDrawElements ( GL_TRIANGLES, 36,GL_UNSIGNED_INT, indices ); when i change WIDTH=HEIGHT=2, and call a glreadpixels with height, width equal to 4 in draw_cube() i can see first 2 pixels with white color, next two with blue(glclearcolor), next two white and then blue and so on.. Now when i change width parameter in glTeximage1D to 16 then ideally i should see alternate patches of white and blue right? But its not the case here. why so?

  Read the article

• BPM 11g - Dynamic Task Assignment with Multi-level Organization Units

  - by Mark Foster

  I've seen several requirements to have a more granular level of task assignment in BPM 11g based on some value in the data passed to the process. Parametric Roles is normally the first port of call to try to satisfy this requirement, but in this blog we will show how a lot of use-cases can be satisfied by the easier to implement and flexible Organization Unit. The Use-Case Task assignment is to an approval group containing several users. At runtime, a location value in the input data determines which of the particular users the task is ultimately assigned to. In this case we use the Demo Community referenced in the SOA Admin Guide, and specifically the "LoanAnalyticGroup" which contains three users; "szweig", "mmitch" & "fkafka". In our scenario we would like to assign a task to "szweig" if the input data specifies that the location is "JapanCentral", to "fkafka" if the location is "JapanNorth" and to "mmitch" if "JapanSouth", and to all of them if the location is "Japan" i.e....   The Process Simple one human task process.... In the output data association of the "Start" activity we need to set the value of the "Organization Unit" predefined variable based on the input data (note that the  predefined variables can only be set on output data associations)....  ...and in the output data association of the human activity we will reset the "Organization Unit" to empty, always good practice to ensure that the Organization Unit will not be used for any subsequent human activities for which we do not require it.... Set Up the Organization Unit  Log in to the BPM Workspace with an administrator user (weblogic/welcome1 in our case) and choose the "Administration" option. Within "Roles" assign the "ProcessOwner" swim-lane for our process to "LoanAnalyticGroup".... Within "Organization Units" we can model our organization.... "Root Organization Unit" as "Japan" and "Child Organization Unit" as "Central", "South" & "North" as shown. As described previously, add user "szweig" to "Central", "mmitch" to "South" and "fkafka" to "North"....   Test the Process Invalid Data  First let us test with invalid data in the input to see what the consequences are, here we use "X" as input.... ...and looking at the instance we can see it has errored.... Organization Unit Root Level Assignment  Now let us see what happens if we have "Japan" in the input data.... ...looking in the "flow trace" we can see that the task has been assigned....  ... but who has the task been assigned to ? Let us look in the BPM Workspace for user "szweig"....  ...and for "mmitch"....  ... and for "fkafka"....  ...so we can see that with an Organization Unit at "Root" level we have successfully assigned the task to all users. Organization Unit Child Level Assignment  Now let us test with "Japan/North" in the input data.... ...and looking in "fkafka" workspace we see the task has been assigned, remember, he was associated with "JapanNorth"....   ... but what about the workspace of "szweig"....  ...no tasks assigned, neither has "mmitch", just as we expected. Summary  We have seen in this blog how to easily implement multi-level dynamic task routing using Organization Units, a common use-case and a simpler solution than Parametric Roles. 

  Read the article

• Updating a database connection password using a script

  - by Tim Dexter

  An interesting customer requirement that I thought was worthy of sharing today. Thanks to James for the requirement and Bryan for the proposed solution and me for testing the solution and proving it works :0) A customers implementation of Sarbanes Oxley requires them to change all database account passwords every 90 days. This is scripted leveraging shell scripts today for most of their environments. But how can they manage the BI Publisher connections? Now, the customer is running 11g and therefore using weblogic on the middle tier, which is the first clue to Bryans proposed solution. To paraphrase and embellish Bryan's solution a little; why not use a JNDI connection from BIP to the database. Then employ the web logic scripting engine to make updates to the JNDI as needed? BIP is completely uninvolved and with a little 'timing' users will be completely unaware of the password updates i.e. change the password when reports are not being executed. Perfect! James immediately tracked down the WLST script that could be used here, http://middlewaremagic.com/weblogic/?p=4261 (thanks Ravish) Now it was just a case of testing the theory. Some steps: Create the JNDI connection in WLS Create the JNDI connection in BI Publisher pointing to the WLS connection Build new data models using or re-point data sources to use the JNDI connection. Create the WLST script to update the WLS JNDI password as needed. Test! Some details. Creating the JNDI connection in web logic is pretty straightforward. Log into hte console and look for Data Sources under the Services section of the home page and click it Click New >> Generic Datasource Give the connection a name. For the JNDI name, prefix it with 'jdbc/' so I have 'jdbc/localdb' - this name is important you'll need it on the BIP side. Select your db type - this will influence the drivers and information needed on the next page. Being a company man, Im using an Oracle db. Click Next Select the driver of choice, theres lots I know, you can read about them I just chose 'Oracle's Driver (Thin) for Instance connections; Versions 9.0.1 and later' Click Next >> Next Fill out the db name (SID), server, port, username to connect and password >> Next Test the config to ensure you can connect. >> Next Now you need to deploy the connection to your BI server, select it and click Next. You're done with the JNDI config. Creating the JNDI connection on the Publisher side is covered here. Just remember to the connection name you created in WLS e.g. 'jdbc/localdb' Not gonna tell you how to do this, go read the user guide :0) Suffice to say, it works. This requires a little reading around the subject to understand the scripting engine and how to execute scripts. Nicely covered here. However a bit of googlin' and I found an even easier way of running the script. ${ServerHome}/common/bin/wlst.sh updatepwd.py Where updatepwd.py is my script file, it can be in another directory. As part of the wlst.sh script your environment is set up for you so its very simple to execute. The nitty gritty: Need to take Ravish's script above and create a file with a .py extension. Its going to need some modification, as he explains on the web page, to make it work in your environment. I played around with it for a while but kept running into errors. The script as is, tries to loop through all of your connections and modify the user and passwords for each. Not quite what we are looking for. Remember our requirement is to just update the password for a given connection. I also found another issue with the script. WLS 10.x does not allow updates to passwords using clear type ie un-encrypted text while the server is in production mode. Its a bit much to set it back to developer mode bounce it, change the passwords and then bounce and then change back to production and bounce again. After lots of messing about I finally came up with the following: ############################################################################# # # Update password for JNDI connections # ############################################################################# print("*** Trying to Connect.... *****") connect('weblogic','welcome1','t3://localhost:7001') print("*** Connected *****") edit() startEdit() print ("*** Encrypt the password ***") en = encrypt('hr') print "Encrypted pwd: ", en print ("*** Changing pwd for LocalDB ***") dsName = 'LocalDB' print 'Changing Password for DataSource ', dsName cd('/JDBCSystemResources/'+dsName+'/JDBCResource/'+dsName+'/JDBCDriverParams/'+dsName) set('PasswordEncrypted',en) save() activate() Its pretty simple and you can expand on it to loop through the data sources and change each as needed. I have hardcoded the password into the file but you can pass it as a parameter as needed using the properties file method. Im not going to get into the detail of that here but its covered with an example here. Couple of points to note: 1. The change to the password requires a server bounce to get the changes picked up. You can add that to the shell script you will use to call the script above. 2. The script above needs to be run from the MW_HOME\user_projects\domains\bifoundation_domain directory to get the encryption libraries set correctly. My command to run the whole script was: d:\oracle\bi_mw\wlserver_10.3\common\bin\wlst.cmd updatepwd.py - where wlst.cmd is the scripting command line and updatepwd.py was my update password script above. I have not quite spoon fed everything you need to make it a robust script but at least you know you can do it and you can work out the rest I think :0)

  Read the article

• Computer Networks UNISA - Chap 15 &ndash; Network Management

  - by MarkPearl

  After reading this section you should be able to Understand network management and the importance of documentation, baseline measurements, policies, and regulations to assess and maintain a network’s health. Manage a network’s performance using SNMP-based network management software, system and event logs, and traffic-shaping techniques Identify the reasons for and elements of an asset managements system Plan and follow regular hardware and software maintenance routines Fundamentals of Network Management Network management refers to the assessment, monitoring, and maintenance of all aspects of a network including checking for hardware faults, ensuring high QoS, maintaining records of network assets, etc. Scope of network management differs depending on the size and requirements of the network. All sub topics of network management share the goals of enhancing the efficiency and performance while preventing costly downtime or loss. Documentation The way documentation is stored may vary, but to adequately manage a network one should at least record the following… Physical topology (types of LAN and WAN topologies – ring, star, hybrid) Access method (does it use Ethernet 802.3, token ring, etc.) Protocols Devices (Switches, routers, etc) Operating Systems Applications Configurations (What version of operating system and config files for serve / client software) Baseline Measurements A baseline is a report of the network’s current state of operation. Baseline measurements might include the utilization rate for your network backbone, number of users logged on per day, etc. Baseline measurements allow you to compare future performance increases or decreases caused by network changes or events with past network performance. Obtaining baseline measurements is the only way to know for certain whether a pattern of usage has changed, or whether a network upgrade has made a difference. There are various tools available for measuring baseline performance on a network. Policies, Procedures, and Regulations Following rules helps limit chaos, confusion, and possibly downtime. The following policies and procedures and regulations make for sound network management. Media installations and management (includes designing physical layout of cable, etc.) Network addressing policies (includes choosing and applying a an addressing scheme) Resource sharing and naming conventions (includes rules for logon ID’s) Security related policies Troubleshooting procedures Backup and disaster recovery procedures In addition to internal policies, a network manager must consider external regulatory rules. Fault and Performance Management After documenting every aspect of your network and following policies and best practices, you are ready to asses you networks status on an on going basis. This process includes both performance management and fault management. Network Management Software To accomplish both fault and performance management, organizations often use enterprise-wide network management software. There various software packages that do this, each collect data from multiple networked devices at regular intervals, in a process called polling. Each managed device runs a network management agent. So as not to affect the performance of a device while collecting information, agents do not demand significant processing resources. The definition of a managed devices and their data are collected in a MIB (Management Information Base). Agents communicate information about managed devices via any of several application layer protocols. On modern networks most agents use SNMP which is part of the TCP/IP suite and typically runs over UDP on port 161. Because of the flexibility and sophisticated network management applications are a challenge to configure and fine-tune. One needs to be careful to only collect relevant information and not cause performance issues (i.e. pinging a device every 5 seconds can be a problem with thousands of devices). MRTG (Multi Router Traffic Grapher) is a simple command line utility that uses SNMP to poll devices and collects data in a log file. MRTG can be used with Windows, UNIX and Linux. System and Event Logs Virtually every condition recognized by an operating system can be recorded. This is typically done using event logs. In Windows there is a GUI event log viewer. Similar information is recorded in UNIX and Linux in a system log. Much of the information collected in event logs and syslog files does not point to a problem, even if it is marked with a warning so it is important to filter your logs appropriately to reduce the noise. Traffic Shaping When a network must handle high volumes of network traffic, users benefit from performance management technique called traffic shaping. Traffic shaping involves manipulating certain characteristics of packets, data streams, or connections to manage the type and amount of traffic traversing a network or interface at any moment. Its goals are to assure timely delivery of the most important traffic while offering the best possible performance for all users. Several types of traffic prioritization exist including prioritizing traffic according to any of the following characteristics… Protocol IP address User group DiffServr VLAN tag in a Data Link layer frame Service or application Caching In addition to traffic shaping, a network or host might use caching to improve performance. Caching is the local storage of frequently needed files that would otherwise be obtained from an external source. By keeping files close to the requester, caching allows the user to access those files quickly. The most common type of caching is Web caching, in which Web pages are stored locally. To an ISP, caching is much more than just convenience. It prevents a significant volume of WAN traffic, thus improving performance and saving money. Asset Management Another key component in managing networks is identifying and tracking its hardware. This is called asset management. The first step to asset management is to take an inventory of each node on the network. You will also want to keep records of every piece of software purchased by your organization. Asset management simplifies maintaining and upgrading the network chiefly because you know what the system includes. In addition, asset management provides network administrators with information about the costs and benefits of certain types of hardware or software. Change Management Networks are always in a stage of flux with various aspects including… Software changes and patches Client Upgrades Shared Application Upgrades NOS Upgrades Hardware and Physical Plant Changes Cabling Upgrades Backbone Upgrades For a detailed explanation on each of these read the textbook (Page 750 – 761)

  Read the article

• Can not print after upgrading from 12.x to 14.04

  - by user318889

  After upgrading from V12.04 to V14.04 I am not able to print. I am using an HP LaserJet 400 M451dn. The printer troubleshooter told me that there is no solution to the problem. This is the output of the advanced diagnositc output. (Due to limited space I cut the output!) Can anybody tell me what is going wrong. I am using the printer via USB ? Page 1 (Scheduler not running?): {'cups_connection_failure': False} Page 2 (Is local server publishing?): {'local_server_exporting_printers': False} Page 3 (Choose printer): {'cups_dest': , 'cups_instance': None, 'cups_queue': u'HP-LaserJet-400-color-M451dn', 'cups_queue_listed': True} Page 4 (Check printer sanity): {'cups_device_uri_scheme': u'hp', 'cups_printer_dict': {'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'printer-info': u'Hewlett-Packard HP LaserJet 400 color M451dn', 'printer-is-shared': True, 'printer-location': u'Pinatubo', 'printer-make-and-model': u'HP LJ 300-400 color M351-M451 Postscript (recommended)', 'printer-state': 4, 'printer-state-message': u'', 'printer-state-reasons': [u'none'], 'printer-type': 8556636, 'printer-uri-supported': u'ipp://localhost:631/printers/HP-LaserJet-400-color-M451dn'}, 'cups_printer_remote': False, 'hplip_output': (['', '\x1b[01mHP Linux Imaging and Printing System (ver. 3.14.6)\x1b[0m', '\x1b[01mDevice Information Utility ver. 5.2\x1b[0m', '', 'Copyright (c) 2001-13 Hewlett-Packard Development Company, LP', 'This software comes with ABSOLUTELY NO WARRANTY.', 'This is free software, and you are welcome to distribute it', 'under certain conditions. See COPYING file for more details.', '', '', '\x1b[01mhp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '', '\x1b[01mDevice Parameters (dynamic data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' back-end hp ', " cups-printers ['HP-LaserJet-400-color-M451dn'] ", ' cups-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' dev-file ', ' device-state -1 ', ' device-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' deviceid ', ' error-state 101 ', ' host ', ' is-hp True ', ' panel 0 ', ' panel-line1 ', ' panel-line2 ', ' port 1 ', ' serial CNFF308670 ', ' status-code 5002 ', ' status-desc ', '\x1b[01m', 'Model Parameters (static data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' align-type 0 ', ' clean-type 0 ', ' color-cal-type 0 ', ' copy-type 0 ', ' embedded-server-type 0 ', ' fax-type 0 ', ' fw-download False ', ' icon hp_color_laserjet_cp2025.png ', ' io-mfp-mode 1 ', ' io-mode 1 ', ' io-support 6 ', ' job-storage 0 ', ' linefeed-cal-type 0 ', ' model HP_LaserJet_400_color_M451dn ', ' model-ui HP LaserJet 400 Color m451dn ', ' model1 HP LaserJet 400 Color M451dn ', ' monitor-type 0 ', ' panel-check-type 0 ', ' pcard-type 0 ', ' plugin 0 ', ' plugin-reason 0 ', ' power-settings 0 ', ' ppd-name lj_300_400_color_m351_m451 ', ' pq-diag-type 0 ', ' r-type 0 ', ' r0-agent1-kind 4 ', ' r0-agent1-sku CE410A/CE410X ', ' r0-agent1-type 1 ', ' r0-agent2-kind 4 ', ' r0-agent2-sku CE411A ', ' r0-agent2-type 4 ', ' r0-agent3-kind 4 ', ' r0-agent3-sku CE413A ', ' r0-agent3-type 5 ', ' r0-agent4-kind 4 ', ' r0-agent4-sku CE412A ', ' r0-agent4-type 6 ', ' scan-src 0 ', ' scan-type 0 ', ' status-battery-check 0 ', ' status-dynamic-counters 0 ', ' status-type 3 ', ' support-released True ', ' support-subtype 2202411 ', ' support-type 2 ', ' support-ver 3.12.2 ', " tech-class ['Postscript'] ", " tech-subclass ['Normal'] ", ' tech-type 4 ', ' usb-pid 3882 ', ' usb-vid 1008 ', ' wifi-config 0 ', '\x1b[01m', 'Status History (most recent first):\x1b[0m', '\x1b[01m Date/Time Code Status Description User Job ID \x1b[0m', ' -------------------- ----- ---------------------------------------- -------- --------', ' 08/21/14 00:07:25 5012 Device communication error richard 0 ', ' 08/20/14 13:42:44 500 Started a print job richard 4214 ', '', '', 'Done.', ''], ['\x1b[35;01mwarning: No display found.\x1b[0m', '\x1b[31;01merror: hp-info -u/--gui requires Qt4 GUI support. Entering interactive mode.\x1b[0m', '\x1b[31;01merror: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '\x1b[31;01merror: Error opening device (Device not found).\x1b[0m', ''], 0), 'is_cups_class': False, 'local_cups_queue_attributes': {'charset-configured': u'utf-8', 'charset-supported': [u'us-ascii', u'utf-8'], 'color-supported': True, 'compression-supported': [u'none', u'gzip'], 'copies-default': 1, 'copies-supported': (1, 9999), 'cups-version': u'1.7.2', 'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'document-format-default': u'application/octet-stream', 'document-format-supported': [u'application/octet-stream', u'application/pdf', u'application/postscript', u'application/vnd.adobe-reader-postscript', u'application/vnd.cups-command', u'application/vnd.cups-pdf', u'application/vnd.cups-pdf-banner', u'application/vnd.cups-postscript', u'application/vnd.cups-raw', u'application/vnd.samsung-ps', u'application/x-cshell', u'application/x-csource', u'application/x-perl', u'application/x-shell', u'image/gif', u'image/jpeg', u'image/png', u'image/tiff', u'image/urf', u'image/x-bitmap', u'image/x-photocd', u'image/x-portable-anymap', u'image/x-portable-bitmap', u'image/x-portable-graymap', u'image/x-portable-pixmap', u'image/x-sgi-rgb', u'image/x-sun-raster', u'image/x-xbitmap', u'image/x-xpixmap', u'image/x-xwindowdump', u'text/css', u'text/html', u'text/plain'], 'finishings-default': 3, 'finishings-supported': [3], 'generated-natural-language-supported': [u'en-us'], 'ipp-versions-supported': [u'1.0', u'1.1', u'2.0', u'2.1'], 'ippget-event-life': 15, 'job-creation-attributes-supported': [u'copies', u'finishings', u'ipp-attribute-fidelity', u'job-hold-until', u'job-name', u'job-priority', u'job-sheets', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-hold-until-default': u'no-hold', 'job-hold-until-supported': [u'no-hold', u'indefinite', u'day-time', u'evening', u'night', u'second-shift', u'third-shift', u'weekend'], 'job-ids-supported': True, 'job-k-limit': 0, 'job-k-octets-supported': (0, 470914416), 'job-page-limit': 0, 'job-priority-default': 50, 'job-priority-supported': [100], 'job-quota-period': 0, 'job-settable-attributes-supported': [u'copies', u'finishings', u'job-hold-until', u'job-name', u'job-priority', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-sheets-default': (u'none', u'none'), 'job-sheets-supported': [u'none', u'classified', u'confidential', u'form', u'secret', u'standard', u'topsecret', u'unclassified'], 'jpeg-k-octets-supported': (0, 470914416), 'jpeg-x-dimension-supported': (0, 65535), 'jpeg-y-dimension-supported': (1, 65535), 'marker-change-time': 0, 'media-bottom-margin-supported': [423], 'media-col-default': u'(unknown IPP value tag 0x34)', 'media-col-supported': [u'media-bottom-margin', u'media-left-margin', u'media-right-margin', u'media-size', u'media-source', u'media-top-margin', u'media-type'], 'media-default': u'iso_a4_210x297mm', 'media-left-margin-supported': [423], 'media-right-margin-supported': [423],

  Read the article

• Session Report - Java on the Raspberry Pi

  - by Janice J. Heiss

  On mid-day Wednesday, the always colorful Oracle Evangelist Simon Ritter demonstrated Java on the Raspberry Pi at his session, “Do You Like Coffee with Your Dessert?”. The Raspberry Pi consists of a credit card-sized single-board computer developed in the UK with the intention of stimulating the teaching of basic computer science in schools. “I don't think there is a single feature that makes the Raspberry Pi significant,” observed Ritter, “but a combination of things really makes it stand out. First, it's $35 for what is effectively a completely usable computer. You do have to add a power supply, SD card for storage and maybe a screen, keyboard and mouse, but this is still way cheaper than a typical PC. The choice of an ARM (Advanced RISC Machine and Acorn RISC Machine) processor is noteworthy, because it avoids problems like cooling (no heat sink or fan) and can use a USB power brick. When you add in the enormous community support, it offers a great platform for teaching everyone about computing.”Some 200 enthusiastic attendees were present at the session which had the feel of Simon Ritter sharing a fun toy with friends. The main point of the session was to show what Oracle was doing to support Java on the Raspberry Pi in a way that is entertaining and fun. Ritter pointed out that, in addition to being great for teaching, it’s an excellent introduction to the ARM architecture, and runs well with Java and will get better once it has official hard float support. The possibilities are vast.Ritter explained that the Raspberry Pi Project started in 2006 with the goal of devising a computer to inspire children; it drew inspiration from the BBC Micro literacy project of 1981 that produced a series of microcomputers created by the Acorn Computer company. It was officially launched on February 29, 2012, with a first production of 10,000 boards. There were 100,000 pre-orders in one day; currently about 4,000 boards are produced a day. Ritter described the specification as follows:* CPU: ARM 11 core running at 700MHz Broadcom SoC package Can now be overclocked to 1GHz (without breaking the warranty!) * Memory: 256Mb* I/O: HDMI and composite video 2 x USB ports (Model B only) Ethernet (Model B only) Header pins for GPIO, UART, SPI and I2C He took attendees through a brief history of ARM Architecture:* Acorn BBC Micro (6502 based) Not powerful enough for Acorn’s plans for a business computer * Berkeley RISC Project UNIX kernel only used 30% of instruction set of Motorola 68000 More registers, less instructions (Register windows) One chip architecture to come from this was… SPARC * Acorn RISC Machine (ARM) 32-bit data, 26-bit address space, 27 registers First machine was Acorn Archimedes * Spin off from Acorn, Advanced RISC MachinesNext he presented its features:* 32-bit RISC Architecture–  ARM accounts for 75% of embedded 32-bit CPUs today– 6.1 Billion chips sold last year (zero manufactured by ARM)* Abstract architecture and microprocessor core designs– Raspberry Pi is ARM11 using ARMv6 instruction set* Low power consumption– Good for mobile devices– Raspberry Pi can be powered from 700mA 5V only PSU– Raspberry Pi does not require heatsink or fanHe described the current ARM Technology:* ARMv6– ARM 11, ARM Cortex-M* ARMv7– ARM Cortex-A, ARM Cortex-M, ARM Cortex-R* ARMv8 (Announced)– Will support 64-bit data and addressingHe next gave the Java Specifics for ARM: Floating point operations* Despite being an ARMv6 processor it does include an FPU– FPU only became standard as of ARMv7* FPU (Hard Float, or HF) is much faster than a software library* Linux distros and Oracle JVM for ARM assume no HF on ARMv6– Need special build of both– Raspbian distro build now available– Oracle JVM is in the works, release date TBDNot So RISCPerformance Improvements* DSP Enhancements* Jazelle* Thumb / Thumb2 / ThumbEE* Floating Point (VFP)* NEON* Security Enhancements (TrustZone)He spent a few minutes going over the challenges of using Java on the Raspberry Pi and covered:* Sound* Vision * Serial (TTL UART)* USB* GPIOTo implement sound with Java he pointed out:* Sound drivers are now included in new distros* Java Sound API– Remember to add audio to user’s groups– Some bits work, others not so much* Playing (the right format) WAV file works* Using MIDI hangs trying to open a synthesizer* FreeTTS text-to-speech– Should work once sound works properlyHe turned to JavaFX on the Raspberry Pi:* Currently internal builds only– Will be released as technology preview soon* Work involves optimal implementation of Prism graphics engine– X11?* Once the JavaFX implementation is completed there will be little of concern to developers-- It’s just Java (WORA). He explained the basis of the Serial Port:* UART provides TTL level signals (3.3V)* RS-232 uses 12V signals* Use MAX3232 chip to convert* Use this for access to serial consoleHe summarized his key points. The Raspberry Pi is a very cool (and cheap) computer that is great for teaching, a great introduction to ARM that works very well with Java and will work better in the future. The opportunities are limitless. For further info, check out, Raspberry Pi User Guide by Eben Upton and Gareth Halfacree. From there, Ritter tried out several fun demos, some of which worked better than others, but all of which were greeted with considerable enthusiasm and support and good humor (even when he ran into some glitches).  All in all, this was a fun and lively session.

  Read the article

• BizTalk: Sample: Context routing and Throttling with orchestration

  - by Leonid Ganeline

  The sample demonstrates using orchestration for throttling and using context routing. Usually throttling is implemented on the host level (in BizTalk 2010 we can also using the host instance level throttling). Here is demonstrated the throttling with orchestration convoy that slows down message flow from some customers. Sample implements sort of quality service agreement layer for different kind of customers. The sample demonstrates the context routing between orchestrations. It has several advantages over the content routing. For example, we don’t have to create the property schema and promote properties on the schemas; we don’t have to change the message content to change routing. Use case:  The BizTalk application has a main processing orchestration that process all input messages. The application usually works as an OLTP application. Input messages came in random order without peaks, typical scenario for the on-line users. But sometimes the big data batch payloads come. These batches overload processing orchestrations. All processes, activated by on-line users after the payload, come to the same queue and are processed only after the payload. Result is on-line users can see significant delay in processing. It can be minutes or hours, depending of the batch size. Requirements: On-line user’s processing should work without delays. Big batches cannot disturb on-line users. There should be higher priority for the on-line users and the lower priority for the batches. Design: Decision is to divide the message flow in two branches, one for on-line users and second for batches. Branch with batches provides messages to the processing line with low priority, and the on-line user’s branch – with high priority. All messages are provided by hi-speed receive port. BTS.ReceivePortName context property is used for routing. The Router orchestration separates messages sent from on-line users and from the batch messages. But the Router does not use the BizTalk provided value of this property, the Router set up this value by itself. Router uses the content of the messages to decide if it is from on-line users or from batches. The message context property the BTS.ReceivePortName is changed respectively, its value works as a recipient address, as the “To” address for the next recipient orchestrations. Those next orchestrations are the BatchBottleneck and the MainProcess orchestrations. Messages with context equal “ToBatch” are filtered up by the BatchBottleneck orchestration. It is a unified convoy orchestration and it throttles the message flow, delaying the message delivery to the MainProcess orchestration. The BatchBottleneck orchestration changes the message context to the “ToProcess” and sends messages one after another with small delay in between. Delay can be configured in the BizTalk config file as:                 <appSettings>                                 <add key="GLD_Tests_TwoWayRouting_BatchBottleneck_DelayMillisec" value="100"/>                 </appSettings>   Of course, messages with context equal “ToProcess” are filtered up by the MainProcess orchestration.   NOTES: Filters with string values: In Orchestrations (the first Receive shape in orchestration) use string values WITH quotes; in Send Ports use string values WITHOUT quotes. Filters on the Send Ports are dynamic; we can change them in run-time. Filters on the Orchestrations are static; we can change them only in design-time. To check the existence of the promoted property inside orchestration use the Expression shape with construction like this:       if (BTS.ReceivePortName exists myMessage) { …; } It is not possible in the Message Assignment shape because using the “if” statement inside Message Assignment is prohibited. Several predefined context properties can behave in specific way. Say MessageTracking.OriginatingMessage or XMLNORM.DocumentSpecName, they are required some internal rules should be applied to the format or usage of this properties. MessageTracking.* parameters require you have to use tracking and you can get unexpected run-time errors in some cases. My recommendation is - use very limited set of the predefined context properties. To “attach” the new promoted property to the message, we have to use correlation. The correlation type should include this property. [Here is a good explanation by Saravana ] The sample code is here [sorry, temporary trubles with CodePlex].

  Read the article

• Yes, I did it - Skydiving in Mauritius

  Finally, I did it or better said we did it. Already back in November last year I saw the big billboard advertisement of Skydive Austral Mauritius near Caudan Waterfront in Port Louis and decided for myself that this is going to be the perfect birthday gift for my wife. Simply out of curiosity I would join her tandem jump with a second instructor. Due to her pregnancy of our son I had to be patient... But then finally, her birthday had arrived and on our midnight celebration session I showed her her netbook with the website preloaded. Actually, it was the "perfect" timing... Recovery from her cesarean is fine, local weather conditions are gorgious and the children were under surveillance of my mum - spending her annual holidays on the island. So, after late wake-up in the morning, we packed our stuff and off we went. According to Google Maps direction indication we had to drive for roughly 50km (only) but traffic here in Mauritius is always challenging. The dropzone is at the Zone Industrielle Mon Loisir Sugar Estate near Riviere du Rempart at the northern east coast. Anyways, we were not in a hurry and arrived there shortly after noon. The access road to the airfield are just small down-driven paths through sugar cane fields and according to our daughter "it's bumpy!". True true true... The facilities at Skydive Austral Mauritius are complete except for food. Enough space for parking, easy handling at the reception and a lot to see for the kids. There's even a big terrace with several sets of tables and chairs, small bar for soft drinks, strictly non-alcoholic. The team over there is all welcoming and warm-hearthy! Having the kids with us was no issue at all. Quite the opposite, our daugther was allowed to discover a lot of things than we adults did. Even visiting the small air plane was on the menu for her. Really great stuff! While waiting for our turn we enjoyed watching other people getting ready in the jump gear, taking off with the Cessna, and finally coming back down on the tandem parachute. Actually, the different expressions on their faces was one of the best parts while waiting. Great mental preparation as my wife was getting more anxious about her first jump... {loadposition content_adsense} First, we got some information about the procedures on the plane about how to get seated, tight up with our instructors and how to get ready for the jump off the plane as soon as we arrive the height of 10.000 ft. All well explained and easy to understand after all.Next, we met with our jumpers Chris and Lee aka "Rasta" to get dressed and ready for take-off. Those guys are really cool and relaxed for their job. From that point on, the DVD session / recording for my wife's birthday started and we really had a lot of fun... The difference between that small Cessna and a commercial flight with an Airbus or a Boeing is astronomic! The climb up to 10.000 ft took us roughly 25 minutes and we enjoyed the magnificent view over the turquoise lagunes near Poste de Flacq, Lafayette and Isle d'Ambre on the north-east coast. After flying through the clouds we sun-bathed and looked over "iced-sugar covered" Mauritius. You might have a look at the picture gallery of Skydive Mauritius for better imagination. The moment of truth, or better said, point of no return came after approximately 25 minutes. The door opens, moving into position on the side on top of the wheel and... out! Back flip and free fall! Slight turns and Wooooohooooo! through the clouds... It so amazing and breath-taking! So undescribable! You have to experience this yourself! Some seconds later the parachute opened and we glided smoothly with some turns and spins back down to the dropzone. The rest of the family could hear and see us soon and the landing was easy going. We never had any doubts or fear about our instructors. They did a great job and we are looking forward to book our next job. I might even consider to follow educational classes on skydiving and earn a license. By the way, feel free to get in touch with Skydive Austral Mauritius. Either via contact details on their website or tweeting a little bit with them. Follow the tweets of Chris and fellows on SkydiveAustral.

  Read the article

• Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

  Read the article

• Easiest, most fun way to program 2D games? Flash? XNA? Some other engine?

  - by Maxi

  Hi, this is a post detailing my search for the most enjoyable way for a hobbyist game programmer to sweeten his free time with making a game. My requirements: I looked at Flash first, I made a couple of small games but I'm doubtful of the performance. I would like to make a fairly large strategy game, with several hundred units fighting simultaneously, explosions and animations included. Also zoomable maps. I saw that Adobe has a new 3D API for Flash, but I don't know if that improves 2D performance aswell, I couldn't find anything related to that question on their MAX10 sessions. Would you say that Flash is a good technology for making large 2D games easily? I really like Actionscript, and I love how easy everything is in Flash. There are several engines available which make it even easier. I just do this for fun, and it would be even better if there were proper animation/particle editors available and if the engine I were to use, would be available for multiple platforms. (so more people can play my game once finished). I'd like to have it available on many mobile platforms aswell. (because I love touch input for some reason) I do know the XNA framework pretty well, but there are no good engines available for it, and it will only run on Windows, which is a huge turn off. Even bigger is, that you need to install the XNA redistributable each time you want to give the game to someone. If I use XNA, I would have to make all the tools myself, and I'd probably have to make them with WPF. (I'd love to make tools with Adobe AIR, but unfortunately the API's for image manipulation etc. are far worse in Flash, than they are in XNA/WPF.) Now, I'm aware that I could make my own engine that supports each of those platforms, but quite frankly, that would be too much work plowing through APIs. After all, I want to make a game, not an engine. So the question becomes: Is there maybe a cross platform (free or free to develop?) engine available that I could use for 2D development? I prefer: C#, Actionscript. I don't mind using c++ if the toolset is above average, but I highly doubt that there is something out there like that. Please prove me wrong :) So summary: I'd like to use Flash, but I don't know if it scales well enough. I'm not a scripter, I want some real APIs that I can work with inside a proper IDE. Just for information, I looked at several alternatives, I'm actually looking for a long time already. You'd help me a lot to make a decision finally. Feature-wise the Flatredball engine would be ideal. But I tried their tools, and quite frankly, they are horrible. Absolutely unusable, I'd need to make my own for sure. I didn't look at their API, but if their tools are so bad, I'm not inclined to look further. Unity3D. This one is quite nice, but I really don't need 3D, and it is quite ...a lot of work to learn. I also don't like that it is so expensive to use for different platforms and that I can only code for it through scripting. You have to buy each platform separately. The editor usability is average, the product overall is good enough for most purposes, but learning it myself would be overkill. Shiva 3D. It looks good enough, but again: I don't really need 3D. The editor usability is a little worse than Unity3D in my opinion and it wasn't clear to me how to start programming. I think it requires C++ for coding, so that's a negative too. I want to have fun, and c# is fun ;) SDL. Quite frankly, I'd still need to port to all those different SDL implementations. And I don't like OpenGL style programming, it's just plain ugly. And it needs c++, I know that there might be some wrappers available, but I don't like to use wrappers, because... Irrlicht. A lot of features, but support seems to be low and it is aimed at enthusiasts. C# bindings get dropped repeatedly. I'm not an engine enthusiast, I just want to make a game. I don't see this happening with Irrlicht. Ogre3D. Way too much work, it's just a graphics engine. Also no multiple platform support and c++. Torque2D. Costs something to use, and I didn't hear a lot of good things about support and documentation. Also costs extra for each platform.

  Read the article

< Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >