Search Results

Search found 12472 results on 499 pages for 'game cables'.

Page 396/499 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >

• Can I use this power supply + case combination without causing problems?

  - by evan

  I am putting together a computer with a Antec P180 case and a Thermaltake TR2 RX 650 W power supply. The problem is that the Antec P180 case has a separate compartment for the power supply. With an opening for the on/off switch + ac connector to one side, a wall with a small hole for cables to route through on top, a wall on the bottom, and on the other side a fan which pushes air from the hard drive compartment to the power supply compartment. I think the design of the case assumes the power supplies fan is on the side next to the on/off switch, but the fan on the power supply I have is on top, which makes me worry about overheating the power supply. There is about half an inch between the top of the power supply and the wall and the other fan should keep air flowing to push out the air that the power supply pushes upwards. Do you think this setup should work, or should I go get another power supply? Thanks!! PS: This computer will be running an Ubuntu server, so it will always be on, but the rest of the components shouldn't be generating as much heat as they would on say a gaming machine.

  Read the article

• VMware vSphere Hypervisor 5 with Intel SPL 5000 in Raid 0 no boot from DVD?

  - by Richard

  I hope this is the correct StackExchange, since I am only using StackOverflow for Web development, but need some help with my server configuration. I would like to install VMware vSphere Hypervisor 5 on my server here at home and run a view machines on it such as Windows Server 2008 and Red Hat. I used to have either OpenSuse or Windows Server 2008 installed but I would like to get into VMWare Hypervisor. My hardware configuration: - Intel S5000PSL with bios version S5000.86B.10.60.0091 build date 10/09/2008 as of read out of bios - E5420 @ 2.5GHz Intel Xeon CPU The Intel Virtualization Technology is enabled in the BIOS - DVD DH20A4P DVD Writer - 8GB ECC Ram I have configured a RAID 0 on my 2 WD 2TB SATA drives I have burned the Hypervisor 5 on an empty DVD and it is bootable, I tested it on my client PC. The main problem here is basically, that I cannot boot the DVD on my server. I have set the Boot Option to the DVD drive. I have booted from the BIOS straight in the DVD drive and it does not work. I do not see any error messages. The only thing I see are the PXE error messages when it tries booting from the network and other devices, obviously without any result. Does anybody know why I cannot boot the DVD? What could cause the problem? I have sucessfully installed Windows Server 2008 via original DVD about 1 year ago, so the DVD drive can read and does work. The DVD drive is available in the BIOS and I have checked all cables and none of them is loose in any way. I even see the light flashing but it does not want to boot from the DVD. I am looking forward to suggestions and things that I should check. Thank you very much

  Read the article

• Can I make two wireless routers communicate using the wireless?

  - by Dana Robinson

  I want to make a setup like this: cable modem <-cable- wireless router 1 <-wireless- wireless router 2 in another room <-cables- PCs in another room Basically, I want to extend my network access across the house and then have a bunch of network jacks available for my office PCs. Right now, I have a cable modem going to a wireless router in one room and a PC with a wireless PCI card in it in the office on the other side of the house. I use internet connection sharing with the other PCs in the office. The problem is that ICS is flaky, especially when I switch to VPN on the Windows box to access files at work. I picked up a wireless USB adapter that I thought I could share among the PCs I work on but I'm not very happy with it so I'm going to return it (NDISwrapper support for it is poor). Is this possible? My wireless experience so far has been pretty straightforward so I have no idea what kind of hardware is available. I've looked at network extenders but those just look like repeaters for signal strength. I want wired network jacks in my office.

  Read the article

• Low framerate on background apps

  - by user1698923

  My problem is that when a game is running in the foreground, in Full Screen mode, any applications on my second monitor (such as youtube videos, videos, not app specific) drop their frame-rate to about 2-3 FPS. It seems like some sort of power management option that I can't track down. As far as I can tell, it's not due to the GPU not being able to keep up. For instance, my PC can play League of Legends at about 280FPS when the framerate is uncapped. If i cap it at 60FPS using the in-game option, it has no affect on the performance of the background app. Summary Operating System Windows 8 Pro 64-bit CPU Intel Core i7 3820 @ 3.60GHz 42 °C Sandy Bridge-E 32nm Technology RAM 12.0GB Triple-Channel DDR3 @ 533MHz (7-7-7-20) Motherboard Gigabyte Technology Co., Ltd. X79-UD3 (SOCKET 0) 37 °C Graphics DELL U2713HM (2560x1440@59Hz) DELL U2713HM (2560x1440@59Hz) 1280MB NVIDIA GeForce GTX 570 (Gigabyte) 58 °C Hard Drives 212GB Volume0 (RAID) 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 36 °C 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 34 °C Optical Drives No optical disk drives detected Audio ASUS Xonar Essence STX Audio Device Operating System Windows 8 Pro 64-bit Computer type: Desktop Graphics Monitor 1 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Secondary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY4\Monitor0 Monitor 2 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Primary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY5\Monitor0 NVIDIA GeForce GTX 570 Manufacturer NVIDIA Model GeForce GTX 570 GPU GF110 Device ID 10DE-1086 Revision A2 Subvendor Gigabyte (1458) Series GeForce GTX 500 Current Performance Level Level 3 Current GPU Clock 845 MHz Current Memory Clock 1900 MHz Current Shader Clock 1690 MHz Voltage 0.988 V Technology 40 nm Die Size 520 mm² Release Date Dec 07, 2010 DirectX Support 11.0 OpenGL Support 5.0 Bus Interface PCI Express x16 Temperature 57 °C Driver version 9.18.13.2018 BIOS Version 70.10.55.00.01 ROPs 40 Shaders 512 unified Memory Type GDDR5 Memory 1280 MB Bus Width 64x5 (320 bit) Filtering Modes 16x Anisotropic Noise Level Moderate Max Power Draw 219 Watts Count of performance levels : 3 Level 1 - "Default" GPU Clock 50 MHz Memory Clock 135 MHz Shader Clock 101 MHz Level 2 - "2D Desktop" GPU Clock 405 MHz Memory Clock 324 MHz Shader Clock 810 MHz Level 3 - "3D Applications" GPU Clock 845 MHz Memory Clock 1900 MHz Shader Clock 1690 MHz Things I've tried: 1) Updating the graphics driver 2) Setting windows power mode to High Performance 3) Reset Nvidia Global Performance settings to default

  Read the article

• Cannot access SMC8014WG-SI provided by TimeWarner/RoadRunner administrative interface...

  - by Matt Rogish

  I just received installation of RoadRunner internet/TV/Voice and I was given a wi-fi router from the TimeWarner folks. The model is a SMC SMC8014WG-SI. Unfortunately, the password it uses is WEP and that is, as we all know, completely insecure. The tech that was here didn't know how to change it to something like WPA2 w/TKIP, and I was on hold for 20 minutes with the TimeWarner folks before I gave up. My problem is that the default web interface (http://192.168.0.1) isn't responding. I can ping it, I can access the internet through it, but I can't get to the admin interface. I did a "hard reset" of the device but still no dice. My suspicion is that the wi-fi admin interface is disabled (a common setting) but the wired interface isn't working on either of my two laptops (I've tried two laptops with two different cables, no link light activated). Am I SOL? Did they lock this down so I can't do what I want to do? Worst-case is I just hook up my go-to WRT54G router to the other modem and leave this one turned off, but I'd rather use their hardware to avoid any "It's not our problem" in the future. Any thoughts? Thanks!!

  Read the article

• iSCSI SAN Implementation with several ESXi hosts and two Equallogic SANs

  - by Sergey

  I work for a small state college. We currently have 4 ESXi hosts (all made by Dell), 2 EqualLogic SANs (PS4000 and PS4100) and a bunch of old HP Procurve switches. The current setup is very far from being redundant and fast so we want to improve it. I read several threads but get even more confused. The Procurve Switches are 2824. I know they don't support Jumbo Frames and Flow Control at the same time, but we have plans to upgrade to something like Procurve 3500yl. Any suggestions? I heard Dell Powerconnects 6xxx are pretty good but I'm not sure how they compare to HPs. There will be a 4-port Etherchannel (Link Aggregation) between the switches, and all control modules on SAN will be connected to different switches. Is there anything that will make the setup better? Are there better switches then Procurves 3500yl that cost less than 5k? What kind of bandwidth can I expect between ESXi hosts (they will also be connected to 2824 with multiple cables) and SANs?

  Read the article

• Cisco SA520 to Adtran 1234 no DHCP transfer

  - by Grico

  I am trying to set up a Cisco SA520 to run DHCP on my network. I have a vendor provided switch, the Adtran 1234, and it provides DHCP for our phone systems on VLAN 200. I do not have access to the Adtran, but the vendor gave me a IP on port 1 for WAN and said port 2 should be for the "trust" side should go. I did setup a mini lab where, Adtran 1 went to SA520 WAN port, and SA520 trust 1 went to my laptop. Everything worked fine, I could ping and get internet using the DHCP scope I put on the SA520. I then unplugged my computer from SA520 trust 1 and plugged it into Adtran 2. I plugged my computer into Adtran 23 and I dont get DHCP or even a link light. If I restart my machine, I get a brief link and then it dies once the machine boots. I have tried several ports on the Adtran and none seem to work. Different cables as well. However, when I plug a phone into the Adtran, the phone boot immediately and shows link. Thoughts?

  Read the article

• Can't connect two PCs to a Network Switch at the same time (Windows 7)

  - by puk

  I have two computers connected to a network switch and every once in a while one of the computers will lose its internet connection. It's almost always the same computer every time. However, if I play around with the control panel, I can switch it, so that now the other computer is not connected. Restarting either of the computers does not help either. In Windows, the worlds-greatest-trouble-shooter tells me that a network cable is unplugged and that I should try plugging it in...Disabling and re-enabling my NIC does not fix this problem, neither does swapping cables around. When rebooting, the BIOS complains about how the Ethernet Cable is not plugged in. If it's in any way important, My set up at the office is like so: Modem - Routher - Network Switch 1 - Network Switch 2. I have tried turning off the energy saving option for my NIC, and I tried manually setting the link-speed to 100Mbps Full Duplex without any luck. Also, I have a Realtek PCIe GBE Family controller on both computers Does anyone have any idea why this is happening every 5-10 days? EDIT: I have also tried using a completely different Network Switch and the problem still persists as before.

  Read the article

• Dell PE2950 - slow IO rates for writing and reading locally

  - by OrenM

  I'm having a serious issue with dell server PE2950. The server has really slow IO rates, so slow that I'm not able to use it anymore I tried few things to solve this: changing disks to new disks (configured them as raid1) changing perc card + perc cables reinstalling the OS of course, had to cause of changing of disks, centos 5.5 x64bit firmware update to everything virtual disks policy: No Read Ahead,Write Back, disk cache policy disabled. openmanage doesn't alert about anything, also i ran dell's diag tests, everything passed, also dell didn't see anything in deset log. dell offered to reseat everything, including the cpu, we did that as well, still io rates are slow I have several PE2950 servers, and I never had such a thing with any of those. All have similar or exact hardware as this one, all configured the same, with the same os centos 5.5 x64, same disks, same raid, same policy. Just for comparison: the problematic PE2950 server: [root@bad ~]# time sh -c "dd if=/dev/zero of=/tmp/ddfile bs=8k count=200000 && sync" 200000+0 records in 200000+0 records out 1638400000 bytes (1.6 GB) copied, 27.7946 seconds, 58.9 MB/s real 0m33.968s user 0m0.531s sys 0m26.000s good PE2950 server (with the exact same hardware): [root@good ~]# time sh -c "dd if=/dev/zero of=/tmp/ddfile bs=8k count=200000 && sync" 200000+0 records in 200000+0 records out 1638400000 bytes (1.6 GB) copied, 3.19999 seconds, 512 MB/s real 0m7.694s user 0m0.053s sys 0m4.057s Hopefully you will have an idea what can cause the problem.

  Read the article

• Why can I not access the internet when Windows 7 finds no issue with the ethernet connection and the network can see my device?

  - by WannabeCoder

  So I just moved from a house to an apartment. In the house and the apartment I had Uverse set up - and in both I had my desktop connected via a ~40 foot long cat5 cable. However, upon moving to the apartment I found that my ethernet connection no longer provides internet. This would seem like a mundane problem if not for: The router can see the computer on the network Windows 7 (the desktop's OS) detects no problems with the ethernet connection. Connections over the internet (i.e. browser windows, Pandora, etc.) do not immediately fail. Instead they load for 2 minutes and then finally give up. Devices connected over the Wifi (PS4, Laptop) access the internet just fine While removing the cat5 cable from my house, I accidentally damaged the locking tab but managed to bend it back into the appropriate position. I would suspect that a bad cat5 cable might be to blame if not for the above issues (thought I've heard bad cat5 cables cause the most nonsensical problems) and the fact that I tested the cat5 cable by having it share internet between my laptop (working internet) to my desktop and it functioned just fine and provided the desktop with internet. My ipconfig /all successfully finds a default gateway, DHCP server, and DNS server. What could possibly be causing the problem?

  Read the article

• Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace

  - by Nick

  I have an laptop top hard drive I was trying to use to my new media computer. The case is small and can accommodate for 2 2.5" drives, no 3.5" drives. I had been using the hard drive as storage hard drive until now. When I go to install Windows on the hard drive first I'm prompted at the bios of: Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace. And then again in the Windows Setup, informing me that the hard drive is bad. So I did a full format of the drive and tried again. Same error. So I took it out and hooked it back up to my other computer via an Sata usb adapter kit (maybe the cause?). The hard drive is recognized fine and when I scanned it for errors by going: right click -> properties -> tools -> error checking It returns that the hard drive is fine. I have tried 3 different SATA cables and multiple jumpers. When I plugged in my 1.5 tb 3.5" drive the computer that gives me the S.M.A.R.T. error on the 2.5" drive, recognizes it with no problems. Any ideas on why this is happening and how I can fix it?

  Read the article

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• Reinserted a RAID disk. Defined as foreign. Is import or clear the correct choice?

  - by Petrus

  I have re-inserted a RAID disk, on a DELL server with Windows Server 2008. The drive-status indicator was changing between a green and amber light, and the monitor gave the following message: There are offline or missing virtual drives with preserved cache. Please check the cables and ensure that all drives are present. Press any key to enter the configuration utility. I pressed a key and the PERC 6/I Integrated BIOS Configuration Utility showed that the RAID Status for that disk was Offline. After reinsertion of the disk the monitor is giving the following message: Foreign configuration(s) found on adapter. Press any key to continue or ‘C’ load the configuration utility, or press ‘F’ to import foreign configuration(s) and continue. After checking around on the net I am uncertain if I should choose import or clear. I cannot find out if an import means importing information from the array/system to the now foreign disk or the other way, i.e. importing information from the foreign disk to the array/system that was actually working fine. Also; if clear is a necessary thing to do ahead of a rebuild of that disk, or if clear means to clear the system to somehow make it ready to import the information from the foreign disk to the array/system, which is not what I want. I imagine that making the wrong choice here might be fatal. Please help clearing this out by telling what to choose and why.

  Read the article

• How to make Windows 7 machine allocate a lot of hard disk cache?

  - by Jian Lin

  I am recording some game play capture (recording playing of PS3 or Wii) using a PC with Windows 7 and Hauppauge 1212 HD Recorder, and I have 4GB of RAM... is there a way to increase the size of Windows 7's hard disk cache size so that writing to the hard drive can be super fast? Since there is at least 1.5GB of RAM not being used, something like allocating 1GB just as hard disk cache, is it possible?

  Read the article

• Getting Camtasia for Windows to record pc/software's audio

  - by Jay Jamison

  i'm building a screencast of a web app / game we've built. its got audio integrated. i've downloaded camtasia for windows. the audio sources i can choose in option have grayed out the option for the source from PC. anyone have any luck troubleshooting this?

  Read the article

• Splitting HDMI sound to 2 devices under Windows 7

  - by Jeramy

  Okay, this is a strange set-up and is frustrating me. I have an HDMI signal from my PC being split to my audio receiver and my HDTV. I need to split it to both so that I can choose to either play audio from the HDTV or from the surround sound speakers in the room. The problem that I am having is in Windows 7, the output is listed under "Playback Devices" and is auto-populated with the HDTV, which only has the option for stereo sound. If I unplug the HDTV from the splitter it will populate with my receiver information and let me set it to 5.1 surround, but as soon as I plug the HDTV back in it reverts. I tried reversing the order of the HDMI cables in the splitter and this seemed to work for a short while, then Windows must have polled the devices again or something because it reverted. It will work as long as Windows identifies the reciever, thereby unlocking the 5.1 surround option, otherwise I am stuck with stereo, which it assumes is all the HDTV is capable of. Is there a way to manually override this and set my own options? Or any other solutions?

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• Combining Two CD-ROMs

  - by bobber205

  Is there any way to combine two CDs? I have two game discs that I would like to put on one CD for easier distribution. These games are very very old and are only about 250 megs for their entire contents. Since they depend on their paths to run correctly, is there a way to write them to a disc in a certain way that makes windows think they're two separate discs?

  Read the article

• Is there a standalone flash player for Linux?

  - by Andy

  I would like to download a flash game and play it without using Firefox under Ubuntu Lucid - any ideas anybody? (Btw I can download it fine, it's the playing it without FF that's the issue!) TIA Andy

  Read the article

• Hints on diagnosing performance issue in OpenBSD firewall

  - by Tom

  My OpenBSD 4.6 pf firewall has started having really bad performance in the past few weeks. I've isolated the firewall (as opposed to the WAN connection, switch, cable, etc.) as the problem, but need a hint on how to further diagnose or fix the problem. The facts: Normal setup is: DSL Modem - FW Ext. NIC - FW Int. NIC - Switch - Laptop Normal setup described above gives only 25 Kbps! Plugging the laptop straight from the DSL modem gives a 1 MBps connection (full speed, as advertised). Therefore, the DSL connection seems to be OK. Plugging the laptop directly into the firewall's internal NIC (bypassing the switch) also gives only 25 Kbps. Therefore, the switch does not seem to be a problem. I've replaced the ethernet cables, but it didn't help. Here's the weird thing. Reloading the ruleset (/sbin/pfctl -Fa -f /etc/pf.conf) causes the laptop's connection to go up to 1 Mbps (i.e. full speed) for a few minutes before it gradually degrades back down to 25Kbps again. Any ideas on what's wrong or how I could further diagnose the problem?

  Read the article

• LCD monitor flicker when connected to a laptop using VGA

  - by Björn Lindqvist

  I have a dual screen setup with two AOC e2450Sw monitors connected to a laptop. The laptop has one HDMI and one VGA output. When one of the monitors is connected using VGA, it flickers or displays static noise. The flickering is fairly subtle and only visible on darker colors. But it is there and noticable and appears like horizontal lines. The problem only appears on the monitor connected to the laptop using the VGA cable. If I swap the monitors, the one connected using VGA is displaying the flicker but not the one connected using HDMI. The simple solution would ofcourse be to connect both monitors using HDMI, but since the laptop only has one VGA and one HDMI out that isn't possible. I've tried tweaking the monitor setting using the OSD menu, but it had little or no effect. Update: After several more trouble shooting hours, it seems the problem is not related to the monitor or VGA cable as the problem persists even if I swap the display with another brand and different cables. So it may be the graphics card? Intel HD Graphics 4000. The laptop is Acer Aspire E1-571.

  Read the article

• Enabling AHCI in BIOS for SSD

  - by Robert

  I am trying to help a friend with a desktop upgrade. It is an old machine with an Intel DG31 main board. The board has 1 IDE port to which a DVD-ROM drive is connected, and 2 SATA ports. 1 SATA port had a hard drive with XP on it. I have made that the secondary drive now and wiped the OS as requested, so it is just for data. The new SSD has been installed but I read that for best results one must enable AHCI in the BIOS? So I checked and in the BIOS there is a SATA Mode setting with 2 options - Native and Legacy. I think Native means AHCI? After setting to Native, I installed Windows 7 Home Premium and all the latest drivers from Intel's website and all Windows Updates. Now when I check Device Manager I see this: Also Microsoft says HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci\Start and HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV\Start should have value 0 for AHCI but I see that the value is 3 for both. So does this mean that Native mode is not AHCI? Or Windows 7 ignored BIOS setting and installed in IDE mode, maybe because both cables are present? Please help me enable AHCI on this system. Thanks!

  Read the article

• SATA HDD not recognized by BIOS after Windows 7 reinstall

  - by RoliSoft

  I got Win32.Virut.56 virus, which is a very nasty stuff. I reinstalled my Win7, but it reappeared somehow. After hours of headache, I was able to remove it by booting into a live Ubuntu and running CureIT using Wine. I then started reinstalling Windows 7. After the "expanding files" stage it rebooted, however from that point on, my 160 GB Western Digital SATAII hard drive was not recognized. The bios just freezes at "SATAII 1: Detecting...". My other 1.5 TB Seagate SATAII hard drive works correctly. I tried switching cables; that didn't help. I googled this issue, but what came up were usually firmware problems. I can't update the firmware or do anything at all, because if I plug it in, it won't start. My motherboard is an ASRock 4Core1333-Viiv, if that helps. I'm now stuck on a live Ubuntu. I can't install Win7 on the 1.5 TB drive, because it's full of data I need. What do you think I could try to make the hdd work again? As for the moment, I don't have another computer to try if that one recognizes the hdd.

  Read the article

• Audio card with built-in ground isolator?

  - by Dave Jarvis

  What audio cards would you recommend that eliminate hum, and hard-drive & mouse movement signal interference? Hardware components: Motherboard. Asus P5Q SE Audio. Realtek ALC 1200, 8-Channel High-Definition Audio CODEC (on board) Harddrive. WD Caviar 320 GB Mouse. Logitech Marbleman USB Mixer. Mackie d.4 Pro Amplifier. Sonance Sonamp 260 All components are plugged into the same Monster Power HDP 910 powerbar (does not help eliminate noise). I have no other components plugged in. The computer uses a Monster iCable 1000 to go from mini (on board audio) to RCA (mixer). I have moved the cable as far from other cables as possible. A ground loop isolator between the mixer and on board audio eliminates all noise. I would rather not use a ground loop isolator; an internal audio card that is Linux-compatible (Kubuntu) would be ideal. Suggestions?

  Read the article

• What is some good lossless video codec for recording gameplay?

  - by Don Salva

  I'm an avid gamer and I like to record my gameplay. Usually I've been using Fraps to do it, however I'm thinking of switching to Dxtory as it allows to write on multiple HDDs at once. Say I have 3 HDDs with the following write speeds: HDD1 with 50 mb/s, HDD2 with 22 mb/s and HDD3 with 45 mb/s. Combined write speed would be: 117 mb/s. Dxtory allows you to utilize all 3 HDD's at once while recording your gameplay. Using this formula: RGB24 YUV24: Width x Height x 3 x fps = bitrate (byte/sec) YUV420: Width x Height x 3 / 2 x fps = bitrate (byte/sec) YUV410: Width x Height x 9 / 8 x fps = bitrate (byte/sec) And recording in YUV420 colorspace at 1920x1080 with 30 fps I'd need about 95 mb/s write speed. Dxtory is good because it allows me to play with constant 60 fps while recording in 30 fps. Fraps does not (even though they say it does), once you start recording with Fraps, the game's fps drops. So I'm looking for a codec that doesn't need a very high write speed (bitrate) yet records in good (lossless) quality. Dxtory comes with its own codec, the Dxtory codec. Which allows me some experimentation. Fraps has it's own codec which I can use in Dxtory to expirement around. I also came across http://lags.leetcode.net/codec.html . Are there more lossless codecs out there (besides Fraps' and Dxtory's) which are good for what I want to do? Edit: To clarify, yes, I'm aware a lossless codec always has "good" quality. But that's not what I'm looking for. Let me take the Fraps codec and Dxtory codec to clarify what I'm looking for. When I record with the Dxtory codec in RGB colorspace at 1920x1080 with targeted 30 fps, I can play the game at 60 fps, BUT I'm recording with 10-15 fps, that's because RGB with Dxtory needs much, much more write speed than my hdd can handle. When recording with Dxtory codec in YUV410 colorspace at 1920x1080 with targeted 30 fps, I can play at 60 fps and record at 30 fps, again, that's because YUV410 in Dxtory's codec takes much, much less write speed than RGB When recording with Fraps codec in ??? (I dunno the color space Fraps records in, I guess YUV420), I can play with 60 fps and record with 30 fps. What I'm looking for is a lossless codec that can record in YUV420 (or even RGB??) which does not exceed a write speed (or bitrate if you will) of 100 mb/s in 1920x1080 or in other words, which will allow me to record in constant 30fps. Obviously the best solution would be to buy an SDD, but that's not what I'm after.

  Read the article

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >