Search Results

Search found 13947 results on 558 pages for 'television shows'.

Page 397/558 | < Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >

  • Setting my NIC to full duplex

    - by David
    I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

    Read the article

  • OpenVPN, install a TAP adapter

    - by GolezTrol
    When I try to connect to my work VPN using OpenVPN, the connection fails with the message: All TAP-Win32 adapters on this system are currently in use. Many sources suggest to look in Control Panel\Network and Internet\Network Connections an enable the TAP adapter, but when I look there, there is none. Now I've run addtap.bat which is provided with OpenVPN, but I still don't get to see any TAP adapter, and logging in in VPN still fails. The output of addtap.bat is C:\Windows\system32>"C:\Program Files (x86)\OpenVPN\bin\tapinstall.exe" install "C:\Program Files (x86)\OpenVPN\driver\OemWin2k.inf" tap0801 Device node created. Install is complete when drivers are updated... Updating drivers for tap0801 from C:\Program Files (x86)\OpenVPN\driver\OemWin2k .inf. Drivers updated successfully. I've Run As Administrator both the setup of OpenVPN and addtap.bat. I've run deltapall.bat to remove any (maybe hidden) adapters. It said it removed three of them, after which I ran addtap.bat again to try to create another one. I also run OpenVPN itself as administrator. What's wrong? Running Windows 7 Home Premium on a HP Pavilion dv7 4050ed. It has worked before, but I recently had to reinstall my laptop, for which I used the restore disks I created when I just got it. Everything else seems to work fine. == UPDATE == The TAP adapter is found in Device Manager, but apparently it is disabled because it is incompatible with Windows 7 64bit. I've deïnstalled OpenVPNGui, downloaded a version that should be 64bit compatible, and installed that. Still no cigar. Then I found a tip to install OpenVPN (version 9) after installing OpenVPNGui, because that installs OpenVPN version 8. Now I got a v9 TAP driver in Device Manager, but it still doesn't work and shows up in device manager with an exclamation mark, and not at all in my network devices.

    Read the article

  • Surprising corruption and never-ending fsck after resizing a filesystem.

    - by Steve Kemp
    System in question has Debian Lenny installed, running a 2.65.27.38 kernel. System has 16Gb memory, and 8x1Tb drives running behind a 3Ware RAID card. The storage is managed via LVM. Short version: Running a KVM guest which had 1.7Tb storage allocated to it. The guest was reaching a full-disk. So we decided to resize the disk that it was running upon We're pretty familiar with LVM, and KVM, so we figured this would be a painless operation: Stop the KVM guest. Extend the size of the LVM partition: "lvextend -L+500Gb ..." Check the filesystem : "e2fsck -f /dev/mapper/..." Resize the filesystem: "resize2fs /dev/mapper/" Start the guest. The guest booted successfully, and running "df" showed the extra space, however a short time later the system decided to remount the filesystem read-only, without any explicit indication of error. Being paranoid we shut the guest down and ran the filesystem check again, given the new size of the filesystem we expected this to take a while, however it has now been running for 24 hours and there is no indication of how long it will take. Using strace I can see the fsck is "doing stuff", similarly running "vmstat 1" I can see that there are a lot of block input/output operations occurring. So now my question is threefold: Has anybody come across a similar situation? Generally we've done this kind of resize in the past with zero issues. What is the most likely cause? (3Ware card shows the RAID arrays of the backing stores as being A-OK, the host system hasn't rebooted and nothing in dmesg looks important/unusual) Ignoring brtfs + ext3 (not mature enough to trust) should we make our larger partitions in a different filesystem in the future to avoid either this corruption (whatever the cause) or reduce the fsck time? xfs seems like the obvious candidate?

    Read the article

  • postfix smtpd rejecting mail from outside network match_list_match: no match

    - by Loopo
    My postfix (V: 2.5.5-1.1) running on ubuntu server (9.04) started to reject mail arriving in from outside about 2 weeks ago. Doing a "manual" session via telnet shows that the connection is always closed after the MAIL FROM: [email protected] line is input, with the message "Connection closed by foreign host." Doing the same from another client inside the LAN works fine. In the log files I get the line "lost connection after MAIL from xxxxx.tld[xxx.xxx.xxx.xxx]" This is after some lines like: match_hostaddr: XXX.XXX.XXX.XXX ~? [::1]/128 match_hostname: XXXX.tld ~? 192.168.1.0/24 ... match_list_match: xxx.xxx.xxx.xxx: no match which seem to suggest some kind of filter which checks for allowed addresses. I have been unable to locate where this filter lives, or how to turn it off. I'm not even sure if that's what's causing my problem. Connections from inside the LAN don't get disconnected even though they also show a "match_list_match: ... no match" line. I didn't change any configuration files recently, below is my main.cf as it currently stands. I don't really know what all the parameters do and how they interact. I just set it up initially and it worked fine (up to recently). smtpd_banner = $myhostname ESMTP $mail_name (GNU) biff = no readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/server.crt smtpd_tls_key_file=/etc/ssl/private/server.key #smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_sasl_auth_enable = no smtp_use_tls=no smtp_sasl_password_maps = hash:/etc/postfix/smtp_auth myhostname = XXXXXXX.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = XXXX.XXXX.com, XXXX.com, localhost.XXXXX.com, localhost relayhost = XXX.XXX.XXX.XXX mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.1.0/24 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all smtpd_sasl_local_domain = #smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_authenticated_header = yes broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,reject_unauth_ when checking the process list, postfix/smtpd runs as smtpd -n smtp -t inet -u -c -o stress -v -v Any clues?

    Read the article

  • ubuntu not detecting CDdrives

    - by Mirage
    Ihave insatlled ubuntu 10.4 on my compuer with 6 cd drives. Now initiallyi had window server 2008 and i had to install marvel raid sata controller and then my window detected all 6 drives. Now ubuntu is detecting only 3 drives and i have not found marvell drivers for ubuntu bt i have drives for window 2008. Now my question is if i have vrtual machine inside ubuntu using vmware workstation and i install that driver. then can VM dtect thse 6 drives or host has to detect those drives first to make VMs use that Ubuntu shows this thing from terminal *-cdrom:0 description: DVD-RAM writer product: DVDRAM GSA-H10N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/scd0 logical name: /dev/sr0 version: JL10 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD writer product: DVDRRW GWA-4164B vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: 1.01 serial: [HL-DT-STDVDRRW GWA-4164B1.0105/05/12 capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc Is t detecting all drives or thise local names just same

    Read the article

  • Network bridge does not work on Windows 7

    - by D. Strout
    I am trying to use Windows 7 to bridge my wireless and wired connections together to get wireless on a second Windows XP computer (fresh install). The network bridge is created successfully, but when I connect the cable from the first computer with the bridged connections to the second one with just a wired connection, nothing happens. The second computer doesn't connect, and the first computer shows no sign of anything different. I tried bridging the connections of a third computer, and connecting this computer to the second computer. This worked (third computer bridged the wireless to the second computer). Thus, the problem must be with the first (Win 7) computer. However, I have no idea what the problem could be. All Internet Connection Sharing is turned off. Homegroup is disabled (it was originally enabled, I thought that might be a problem, so I disabled it). Also, I had VMWare fusion installed, and that created extra items in the "This connection uses the following items" box in the properties dialog. Thinking this might be causing issues, I uninstalled that too. Still, with everything I tried, I can't get it to work. Any suggestions? Edit: Another thing I noticed that might be worth mentioning: The network icon in the Win7 taskbar has a red X on it that means it's not connected, but when I click the icon, it says connected next to my wireless connection, and I am able to access the internet.

    Read the article

  • Warning for "Reallocated Event Count" S.M.A.R.T. attribute with a new/unused drive. How serious is t

    - by Developer Art
    I've just looked at the health status of my old 2,5 inch 500 Gb Fujitsu drive with a popular "HD Tune" utility. It shows a warning for the "Reallocated Event Count" property. How serious is that? The thing is that the drive is practically new. I pulled it out of a new laptop over a year ago and never used it since. Right now it only has 53 "Power On" hours which sounds about right since I only had it running a few evenings overnight before switching it for something more performant. Does this warning indicate that the drive is likely to fail some time in the future? I'm somewhat perplexed since the drive is effectively unused. What is more, I have arranged with somebody to buy off this drive since I don't really need. It is 12,5 mm thick (with 3 plates) meaning it doesn't fit into an external enclosure which makes it quite useless to me. Can I give away the drive without having it on my conscience or better cancel the deal? In other words, can the drive be used safely for years to come or better throw it away? I'm running a sector test now to see if there are any real problems. Will post the results as soon as they're available.

    Read the article

  • Apache2 slow serving static while healthy

    - by user45339
    My Apache status looks like; 201 requests/sec - 98.8 kB/second - 504 B/request 85 requests currently being processed, 345 idle workers _____CCW_C_____C__C__C_R____C_WC_________C__C____CW__C__CCC_____ __C____W______C___C___CW__C_C______C__W_C__C_____CCC____C______R CC_C_______C___C____C______________C______C__C________________C_ ___________________C______________________C_______C___C_____C___ CC____C__C___R_____C_C_CC__________C___C___________R____C_C_C___ ______C______W_W__W___C____________________C__WCC__R__R_C_______ R__RC________________________C___R____W__C____.................. .................................................... Server load is average 2 on a 4 core machine. IO utilization is 10-15% and doesn't have many jumps over 70%. Machine has almost 4 gb free and uses 0 swap. The site on the machine is a PHP site. All PHP code is optimized and fast mostly when it gets accessed, however sometimes requests get stuck. Stuck meaning; no response for at least 10 sec. We debugged the PHP code, but it is quite optimal and fast. We spend a lot of time on it until we decided to test the requesting of: <html><body>test</body></html> test.html page. This static resource also gets 'stuck' in the same manner the php pages get 'stuck'. How is the possible given the health of the system? I tested the network, but, when the PHP shows 'slowness' in the site monitoring, the html test files also take (far longer) than 10 sec to load using; time lynx -dump http://127.0.0.1/test.html We are kind of desperate to solve this problem, but we cannot seem to tackle it.

    Read the article

  • Windows 7 64-bit installation from alternative media (no DVD/USB Flash drive)

    - by Niels Willems
    Greetings I currently have Windows 7 x86 installed on my computer. I want to install Windows 7 x64 on a different partition on my computer. However there is a little issue, I cannot run the x64 install from Windows 7 x86 which I currently have. I was planning to Install Windows 7 x64 on another partition to then boot up from that partition to install it on the partition I actually want my OS on. Once that is complete I could just format the partition from the Windows 7 x64 that I didn't need anymore. But the installer will not run from the x86 version of Windows 7 even though I do not want to upgrade that Windows directly. The reason I'm doing this in such a weird way is that my optical drive is broken and I'm really not into buying a new one since I would use it like once every year or so. I also don't have a USB Flash Drive which is big enough to hold the installation files. As far as I'm aware I cannot use an external hard drive such as this one, which I do have. Are there any alternatives in which I can install Windows 7 x64 or am I forced into buying a USB Flash Drive or new optical drive? Thank you in advance for your replies. Edit: This picture shows my current partitions on my laptop. I want to get Windows 7 x64 on the C partition but have to install it first on the F partition to then boot up the F partition windows to format C and install x64 on that one. My external drive is J. Edit 2: No alternative computer which has a DVD drive, install files are located on an iso from MA3D. To install my 32 bit version I mounted the ISO in Daemon Tools to replace my Windows Vista but since I cannot run 64 bit into my 32 bit OS this doesn't work.

    Read the article

  • (13) Permission denied on Apache CGI attempt

    - by ncv
    I have recently upgraded my Apache2 server, and am now unable to run a CGI app. My logs are showing (13) Permission denied unable to connect to cgi deamon after multiple tries I understand that the error message means Apache is being denied some permission to some file, and I'm stumped as to how to track down and solve the problem. Is the file mentioned in the error message truly the blocked file? Or might the problem be caused by some other needed file? The .cgi file is right where it has always been, under /usr/share. The file ownership (root) and permissions (world readable/executable) are the same as they have always been for the file and its ancestors. The SELinux file labels are unchanged. The SELinux audit log shows no denial associated with Apache nor the CGI program. In case of a donotaudit condition, I enabled audit, but still saw nothing. I switched SELinux into permissive mode briefly, to no avail. I even tried restarting Apache while in permissive mode. This did not solve the problem. Any suggestions on how to solve this problem? I'm tempted to just revert to the older Apache.

    Read the article

  • Group Policy Software Installs Too Silent on Windows 7

    - by jonblock
    I'm trying to migrate a Windows XP deployment process to Windows 7. The process has been surprisingly smooth, after figuring out how to bring up a base system. We rely heavily on Group Policy software installation, which in XP can mean long periods on any given morning sitting around watching the machine install new updates. At least the typical Windows Installer message shows the user that something is indeed happening. As far as I can tell, Windows 7 retains the startup installation process (good), but eliminates the on-screen message to indicate what's happening (bad). All a user will see, possibly for a half-hour or more if they haven't restarted for a while, is the electric hamster wheel and the words "Please wait...". I forsee a significant increase in support calls... If you're familiar with msiexec.exe parameters, XP behaves like /qb-, and 7 behaves like /qn. I want the /qb- behavior back. Is there a way to re-enable the Windows Installer notices for Group Policy startup installations?

    Read the article

  • HAProxy "503 Service Unavailable" for webserver running on a KVM virtual machine

    - by Menda
    I'm setting up a server with KVM (IP 192.168.0.100) and I have created inside of it one virtual machine using network bridging at 192.168.0.194. This virtual machine has an nginx instance running, which I can access from the server or from any computer computer in the internal network just typing in the browser http://192.168.0.194. However, I try configure HAProxy in the same server that hosts KVM and looking the status page of HAProxy it always shows the virtual machine as "DOWN". If I try from the server http://localhost, it should be the same than if I go to http://192.168.0.194. My goal is to build a reverse proxy, but I tried this little example and won't work. What am I doing bad? This is my config file in the server: # /etc/haproxy/haproxy.cfg global maxconn 4096 user haproxy group haproxy daemon defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen ServerStatus *:8081 mode http stats enable stats auth haproxy:haproxy listen Server *:80 mode http balance roundrobin cookie JSESSIONID prefix option httpclose option forwardfor option httpchk HEAD /check.txt HTTP/1.0 server mv1 192.168.0.194:80 cookie A check Thanks.

    Read the article

  • windows clients cannot get dns resolution until you open and close ipv4 properties page

    - by GC78
    This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

    Read the article

  • Openfiler crashing without cause or leaving any log messages

    - by user44725
    So my linux machine keeps crashing, without so much as a bye or a leave. I've tried and tried and failed again to work out whats happening. Any help would be much appreciated. Linux chai 2.6.29.6-0.24.smp.gcc3.4.x86_64 #1 SMP Tue Mar 9 05:06:08 GMT 2010 x86_64 x86_64 x86_64 GNU/Linux Openfiler Here is what the /var/log/messages file says at the time of the latest crash. Nothing that unusual - just greg logging in and out via samba. You'll notice there is a cron running for root every minute - ignore this - this isn't the issue either it was some check I've been doing to discover its problem. Jun 2 10:32:01 chai crond(pam_unix)[16529]: session closed for user root Jun 2 10:32:49 chai samba(pam_unix)[15454]: session opened for user greg by (uid=0) Jun 2 10:33:01 chai crond(pam_unix)[16537]: session opened for user root by (uid=0) Jun 2 10:33:04 chai crond(pam_unix)[16537]: session closed for user root Jun 2 10:41:40 chai syslogd 1.4.1: restart. Jun 2 10:41:43 chai syslog: syslogd startup succeeded That restart was called manually by hand - by clicking the restart button on the box. So basically messages isn't revealing many secrets. dmesg only shows from startup. If there is any output I should paste. Just say when and where and it'll be done. Thanks for your help! Tim

    Read the article

  • JVM system time runs faster than HP UNIX OS system time

    - by winston
    Hello I have the following output from a simple debug jsp: Weblogic Startup Since: Friday, October 19, 2012, 08:36:12 AM Database Current Time: Wednesday, December 12, 2012, 11:43:44 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:45:38 AM Line 1 was a recorded variable during WebLogic webapp startup. Line 2 was output from database query select sysdate from dual; Line 3 was output from java code new Date() I have checked from shell date command that line 2 output conforms with OS time. The output of line 3 was mysterious. I don't know how it comes from Java VM. On another machine with same setting, the same jsp output like this: Weblogic Startup Since: Tuesday, December 11, 2012, 02:29:06 PM Database Current Time: Wednesday, December 12, 2012, 11:51:48 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:51:50 AM Another machine: Weblogic Startup Since: Monday, December 10, 2012, 05:00:34 PM Database Current Time: Wednesday, December 12, 2012, 11:52:03 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:52:07 AM Findings: the pattern shows that the longer Weblogic startup, the larger the discrepancy of OS time with JVM time. Anybody could help on HP JVM? On HP UNIX, NTP was done daily. Anyway here comes the server versions: HP-UX machinex B.11.31 U ia64 2426956366 unlimited-user license java version "1.6.0.04" Java(TM) SE Runtime Environment (build 1.6.0.04-jinteg_28_apr_2009_04_46-b00) Java HotSpot(TM) Server VM (build 11.3-b02-jre1.6.0.04-rc2, mixed mode) WebLogic Server Version: 10.3.2.0 Java properties java.runtime.name=Java(TM) SE Runtime Environment java.runtime.version=1.6.0.04-jinteg_28_apr_2009_04_46-b00 java.vendor=Hewlett-Packard Co. java.vendor.url=http\://www.hp.com/go/Java java.version=1.6.0.04 java.vm.name=Java HotSpot(TM) 64-Bit Server VM java.vm.info=mixed mode java.vm.specification.vendor=Sun Microsystems Inc. java.vm.vendor="Hewlett-Packard Company" sun.arch.data.model=64 sun.cpu.endian=big sun.cpu.isalist=ia64r0 sun.io.unicode.encoding=UnicodeBig sun.java.launcher=SUN_STANDARD sun.jnu.encoding=8859_1 sun.management.compiler=HotSpot 64-Bit Server Compiler sun.os.patch.level=unknown os.name=HP-UX os.version=B.11.31

    Read the article

  • Windows 7 blank dvi screen

    - by user99
    I've just upgraded to Windows 7 Ultimate 64 bit. I had an issue during installation; after setup rebooted instead of going to the 'Completing installation' screen I just got a blank screen. I eventually(!) figured out that this meant 'un-plug your second monitor to proceed'. When I did this, installation completed in a snap and everything runs fine. However, whenever I plug my second monitor into my PC, it gets no signal, the the primary monitor removes all windows. icons, the taskbar and the cursor just shows the desktop wallpaper. I'm running a GTS8800 512mb, with the latest drivers (197 IIRC). The monitors are identical, and both plug into DVI sockets on the graphics card, the only difference is I connect one using a straight DVI cable and the other using a VGA cable and a VGA-DVI converter. It's the DVI cabled one that has the issues (if I plug it in by itself it gets no signal). Everything was working fine before I upgraded to Windows 7 (I used to run XPSP2). Anyone have any ideas?

    Read the article

  • nxclient crashes when trying to open a terminal from a remote client through "ssh -Y"

    - by user167328
    I support around 150 linux machines. I have 2 virtual machines on an ESXi server which I access via nxmachine v3 from a windows 7 box. These machines run CentOS5 with KDE and Lubuntu12.04.1 and they are the admin GUIs from which I support the 150 machines. The linux machines which I manage are redhat4/5, CentOS5 and ubuntu 10 and 12. Normally I contact the machines via ssh -Y. Today I did an ssh -Y to a remote machine which is running Ubuntu 12.10 and ssh 6.0p1. Then I tried to open an lxterminal on the remote machine which should display on my KDE desktop. This immediately and reproducably crashed my nxclient session. I tried again from my lubuntu system with the same effect. I have not observed the phenomenon from other machines yet. The message log on my KDE host shows: Unexpected termination of nxagent because of signal: 11 Logger::log nxnode 3920 Googling for this revealed no usable answer. Does anybody have a clue what is going on here or can give a hint how to solve the issue? Add On: I asked the user at the remote machine to export his DISPLAY to my host and open an lxterminal. This worked without problems i. e. the nxclient did not crash. Then the user tried to send me xeyes and this also killed the nxclient with the same error message found in the message log as above. This makes me suspect that the problem is not solely connected to ssh but maybe to some library stuff.

    Read the article

  • Apache2 Segmentation fault with wsgi_module

    - by a coder
    Apache 2.2.3 is running as an existing web server under RHEL 5. Attempting to set up Trac using wsgi_module. RHEL 5 ships with python 2.4, so in order to use the current version of Trac (1.0) I needed to install it with easy_install-2.6. Trac works with the default mod_python, however users strongly encourage not using this module as it is officially dead. Using RHEL's package manager, I downloaded/installed python26-mod_wsgi.so. I backed up the httpd.conf, then made the following additions: LoadModule wsgi_module modules/python26-mod_wsgi.so #...# WSGIScriptAlias /trac /www/virtualhosts/trac/deploy/cgi-bin/trac.wsgi <Directory /www/virtualhosts/trac/deploy/cgi-bin> WSGIApplicationGroup %{GLOBAL} Order deny,allow Allow from all </Directory> Next I moved trac.conf to trac.conf.bak (contains mod_python calls). I tested the configuration using: apachectl configtest Syntax is OK. So I reloaded the server config using: service httpd reload At this time, all virtualhosted sites stopped responding. I restored my backup copy of httpd.conf, reloaded the server config, and the virtualhosted sites are being served again. A quick look at the httpd error_log shows: [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28282): Initializing Python. [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28280): Attach interpreter ''. [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1817): proxy: grabbed scoreboard slot 0 in child 28283 for worker proxy:reverse [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1836): proxy: worker proxy:reverse already initialized [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1930): proxy: initialized single connection worker 0 in child 28283 for (*) [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28283): Initializing Python. [Mon Oct 08 10:20:04 2012] [notice] child pid 28249 exit signal Segmentation fault (11) [Mon Oct 08 10:20:04 2012] [notice] child pid 28250 exit signal Segmentation fault (11) [Mon Oct 08 10:20:04 2012] [notice] child pid 28251 exit signal Segmentation fault (11) There are many similar lines, this is just a snip of the log file. Suggestions on what could be going on to cause the Segmentation faults?

    Read the article

  • Apache web logs "GET http/1.1" 200 error?

    - by songdogtech
    I've got some puzzling (at least to me) errors that show up in my webserver logs. What's puzzling is that they show my error page being referenced, but that error page doesn't show up as being displayed in hits on statcounter.com. Can someone tell me the difference in these two kinds of errors? Or is only one a "real" error? This is in WordPress, and I have my 404.php file in my theme redirecting to a static Wordpress page at mydomain.com/error/ These first two log entries show /error/, but a "hit" on my /error/ page doesn't show in my webstats. The page referenced - /2009/08/delete-preference-files/ - exists, and shows a "hit" at statcounter. 92.17.232.242 - - [13/Mar/2010:01:45:43 -0800] "GET /error/ HTTP/1.1" 200 4012 "http://markratledge.com/2009/08/delete-preference-files/" "Mozilla/5.0 (Windows;U; Windows NT 5.1; en-US; rv:1.9.1.8) Gecko/20100202 Firefox/3.5.8 (.NET CLR 3.5.30729)" 732 4432 92.17.232.242 - - [13/Mar/2010:01:47:11 -0800] "GET /error/ HTTP/1.1" 200 4012 "http://markratledge.com/wp-content/themes/default/style.css" "Mozilla/5.0(Windows; U; Windows NT 5.1; en-US; rv:1.9.1.8) Gecko/20100202 Firefox/3.5.8 (.NET CLR 3.5.30729)" 861 4432 These are two error entries that display my /error/ page, because /error/ gets a "hit" in statcounter. The page /cookies/ doesn't exist. 72.174.16.202 - - [13/Mar/2010:10:53:37 -0800] "GET /cookies HTTP/1.1" 302 21 "-" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.2) Gecko/20100115 Firefox/3.6 (.NET CLR 3.5.30729)" 394 642 72.174.16.202 - - [13/Mar/2010:10:53:38 -0800] "GET /error/ HTTP/1.1" 200 4012 "-" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.2) Gecko/20100115 Firefox/3.6 (.NET CLR 3.5.30729)" 393 4432

    Read the article

  • Choose identity from ssh-agent by file name

    - by leoluk
    Problem: I have some 20-30 ssh-agent identities. Most servers refuse authentication with Too many failed authentications, as SSH usually won't let me try 20 different keys to log in. At the moment, I am specifying the identity file for every host manually, using the IdentityFile and the IdentitiesOnly directive, so that SSH will only try one key file, which works. Unfortunately, this stops working as soon as the original keys aren't available anymore. ssh-add -l shows me the correct paths for every key file, and they match with the paths in .ssh/config, but it doesn't work. Apparently, SSH selects the indentity by public key signature and not by file name, which means that the original files have to be available so that SSH can extract the public key. There are two problems with this: it stops working as soon as I unplug the flash drive holding the keys it renders agent forwarding useless as the key files aren't available on the remote host Of course, I could extract the public keys from my identity files and store them on my computer, and on every remote computer I usually log into. This doesn't looks like a desirable solution, though. What I need is a possibility to select an identity from ssh-agent by file name, so that I can easily select the right key using .ssh/config or by passing -i /path/to/original/key, even on a remote host I SSH'd into. It would be even better if I could "nickname" the keys so that I don't even have to specify the full path.

    Read the article

  • How should I monitor memory usage/performance in SunOS/Solaris?

    - by exhuma
    Last week we decided to add some SunOS (uname -a = SunOS bbs-sam-belair 5.10 Generic_127128-11 i86pc i386 i86pc) machines into our running munin instance. First off, the machines are pre-configured appliances, so, I want to avoid touching the system too much without supervision of the service provider. But adding it to munin was fairly easy by writing a small socket-service (if anyone is interested, I put it up on github: https://github.com/munin-monitoring/contrib/tree/master/tools/pypmmn) Yesterday, I implemented/adapted the required plugins for our machines. And here the questions start: First, I have not found a way to determine detailed memory usage values. I get the total memory by running prtconf | grep Memory, and the free memory using vmstat. Fiddling together a munin-plugin, gives me the following graph: This is pretty much uninformative. Compare this to the default plugin for linux nodes which has a lot more detail: Most importantly, this shows me how much memory is actually used by applications. So, first question: Is it possible to get detailed memory information on SunOS with the default system tools (i.e. not using top)? Onto the next puzzle: Seeing the graphs, I noticed activity in the "Paging in/out" graphs, even though the memory graph still has unused memory: Upon further investigation, I found out that df reports that /tmp is mounted on swap. Drilling around on the web, I understood that df will display swap, but in fact, it's mounted as a tmpfs. Now I don't know if this explains the swap activity. The default munin-plugin for solaris uses kstat -p -c misc -m cpu_stat to get these values. I find it already strange that this is using the cpu_stat module. So maybe I simply misinterpret the "paging" graphs? Second question: Do the paging graphs indicate that parts of the memory are paged to disk? Or is the activity caused by file operations in /tmp?

    Read the article

  • Cannot connect to FTP sites anymore

    - by Wayne M
    I have the FTP service running on Server 2003, and I am hosting websites through Apache. I have users configured to point to certain directories on the server. I am using FileZilla to remote FTP, but it never seems to connect to the directory. The command window says: Command: USER wayne Response: 331 Password required for wayne Command: PASS: ***** Response: 230 User wayne logged in Status: Connected Status: Retrieving directory isting... Command: PWD Response: 257 "/wayne" is current directory Command: TYPE I Response: 200 Type set to I. Command: PASV And that's it. It doesn't display any directories at all, and the pane says "Not connected to any server". Sometimes it will display the folder, but nothing happens when I click on it to expand it. It was working fine, and I have another FTP server set up the same way that does work. How can I fix this? EDIT: I've tried changing it to Active FTP, and it says: Command: LIST Command: 150 Opening BINARY mode data connection for /bin/ls Response: 425 Can't open data connection. Error: Failed to retrieve directory listing. I also noticed that I'm not able to browse the site in IIS's management console anymore, it just shows a blank screen when I click on one of the names and says There are no items to show in this view, although the name has permissions to view the folder and everything. Could it be because I have the Web Publishing service disabled (as I'm not using IIS to host websites)? That shouldn't cause anything should it?

    Read the article

  • NTBackup Error: C: is not a valid drive

    - by Chris
    I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

    Read the article

  • USB drive dead after stopping copying process on Snow Leopard Server

    - by Anriëtte Combrink
    Hi there I was copying to a flash drive from our Snow Leopard server when I stopped the copying process half way through. The device then disappeared from the Desktop. So I unplugged it and plugged it right back in. The device just didn't show up. I unplugged it and plugged it into a Windows XP machine as well as a Windows 7 machine. On both machines, I right clicked "My Computer" and selected "Manage…". On both PC's, the device was located under Removable Storage, but had no size and no drive letter. It shows up in "My Computer", but when I choose "Format…" from the right-click menu (context menu), it says the drive could not be formatted. Can someone please advise me? The flash drives is about 5 mins old and should have no reason to be dead. I really can't loose this drive (I don't need the data on it, I just need it to work again), any help would be appreciated. Thanks in advance.

    Read the article

  • Formatted C: from Windows 7 setup, now it won't even install

    - by ocurro
    Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

    Read the article

< Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >