Search Results

Search found 13947 results on 558 pages for 'television shows'.

Page 398/558 | < Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• Formatted C: from Windows 7 setup, now it won't even install

  - by ocurro

  Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

  Read the article

• Photoshop CS6 Corrupted File recovery

  - by Ben Franchuk

  Last night I was working on a client application mock-up in photoshop, but was goin to take a break from my work so I saved the .PSD file on my internal HDD and put my computer into stand-by mode once the file had finished saving. Unfortunately my computer crashed while it was entering stand-by and shut itself down (photoshop was still open). I did not boot it again to make sure all my files were ok because they had already been saved, but today once I opened up the file again it was extremely corrupted and also completely un-editable (screenshot bellow). so what im asking is there any way to recover my work, or at least some of it? i have put in a good few days work on this project and would hate to have to restart it. the size of the file is 3070 KB, even though it reads as 712 KB in photoshop. i dont know if these file sizes are larger or either smaller than the original non-corrupted file's size, but considering all the layers in the file i suspect it was larger before it corrupted. im using windows XP professional 32bit SP3. both my OS and said .PSD file are located on the same internal HDD (74.4 GB). i do have an external HDD (1.5 TB) but i primarily only use it for movies music and tv shows. i dont know if it was plugged in t the time of me editing the document last, though, if it means anything. i have tried many image and PSd recovery softwares but none have returned any results that may help recover my work. edit: i tried using a photo reccovery software (odboso Photorecovery) that actually seems to recover the corrupted file in question judging by the size of the file, but i cannot recover it because of the licence fee. knowing that the file is still likely on my HDD, what location might it be located?

  Read the article

• Cannot access drive in Windows 7 after scandisk lockup, but can in safe mode....

  - by Matt Thompson

  I ran scandisk on my external USB drive due to the inability to delete a few files. Windows asked me if I wanted to unmount the drive before the scan, warning me that it would be unusable until the scan was finished, and I said yes. During the scan, my machine locked up, and I was forced to reboot the machine. When it came up, I was unable to access the drive, getting an error that "L:is not accessible, access is denied". Comupter Management sees the drive, and has the proper amount of disk space filled. I booted into safe mode, and can access the drive with no problems, and I noticed that in explorer, all the folders have locks on them. I booted back into windows, but still could not access the drive, getting the same error as above. Hovever, if I right click on the drive, select properties, and go to Customize, in the folder pictures ares, I select Choose File, and a window open up, that shows the root of the directory, with all the folder able to be accessed, but again, the icon is the folder icon with a lock on it. I can even copy files from the drive to another. So, the files are not gone, windows can obviously access the drive no matter what it thinks, so there has to be a problem with the flag windows put on the drive when it ran the original scan that failed. I was able to run a scan both in safe mode with no problems, and in windows. In windows, I received the cannot access error the first time I run scan disk on it, but if I try again, it works fine. Any ideas on how to clear the flag that windows set, so I can access the drive normally again?

  Read the article

• mod_cache not working

  - by Pistos

  I have a PHP site that has many dynamically generated pages. I'm trying to turn to mod_cache to help boost performance, because in most cases, content does not change in a given day. I have configured mod_cache as best I could, following examples around the web, including the mod_cache page on apache.org. When I set LogLevel debug, I see a bit of information about the caching that is [not] happening. There are plenty of pairs of lines like this: [Fri Jun 01 17:28:18 2012] [debug] mod_cache.c(141): Adding CACHE_SAVE filter for /foo/bar [Fri Jun 01 17:28:18 2012] [debug] mod_cache.c(148): Adding CACHE_REMOVE_URL filter for /foo/bar Which is fine, because I've set CacheEnable disk /foo, to indicate that I want everything under /foo cached. I'm new to mod_cache, but my understanding about these lines is that it just means that mod_cache has acknowledged that the URL is supposed to be cached, but there are supposed to be more lines indicating that it is saving the data to cache, and then later retrieving them on subsequent hits to the same URL. I can hit the same URL till I'm blue in the face, whether with F5 refreshing, or not, or with different browsers, or different computers. It's always that pair of lines that shows in the logs, and nothing else. When I set CacheEnable disk /, then I see more activity. But I don't want to cache the entire site, and there are many, many different subpaths to the site, so I don't want to have to modify code to set no-cache headers in all the necessary places. I'll mention that mod_rewrite is in use here, rewriting /foo/bar to something like index.php?baz=/foo/bar, but my understanding is that mod_cache uses the pre-rewrite URL, not the post-rewrite URL. As far as I can tell, I have the response headers not getting in the way of caching. Here's an example from one hit: Cache-Control:must-revalidate, max-age=3600 Connection:Keep-Alive Content-Encoding:gzip Content-Length:16790 Content-Type:text/html Date:Fri, 01 Jun 2012 21:43:09 GMT Expires:Fri, 1 Jun 2012 18:43:09 -0400 Keep-Alive:timeout=15, max=100 Pragma: Server:Apache Vary:Accept-Encoding mod_cache config is as follows: CacheRoot /var/cache/apache2/ CacheDirLevels 3 CacheDirLength 2 CacheEnable disk /foo What is getting in the way of mod_cache doing its job of caching?

  Read the article

• How to embed Arial in PDF when PDF has Helvetica?

  - by Brooks Moses

  So, I've got a PDF file that's generated by a program that uses the Base 14 fonts, so that it contains "Helvetica" and "Times Roman". When I look at that in my copy of Acrobat 7.0 on Windows (for example), it shows these with Arial and Times New Roman. I'm fine with that. The issue is that I'd like to publish this PDF file on lulu.com, and they want all fonts embedded. Including the Base 14. I don't have a copy of Helvetica, so what seems the natural thing to do is substitute Arial for Helvetica and embed Arial. How can I do that? I tried using the Print feature in Acrobat (note: this is the full version, not Reader) to print to a PDF file using Adobe's "Print to PDF" printer driver, and selected the "Embed All Fonts" option in the print settings. This worked for the fonts that I had actual copies of, but instead of "printing" Arial for Helvetica -- which it would do if printing to a real printer -- it leaves all the Helvetica as Helvetica and doesn't embed it. Any suggestions for alternate ways to do this? What I really want is just a copy of my PDF file with ALL fonts embedded, and I'm quite happy if doing that means making one of the usual substitutions for the "Helvetica" that's in it. I'd be happiest if I can do that within Acrobat or other software that I have (pdftex, maybe?), but I'm willing to install another free utility if I need to.

  Read the article

• Not playing .mov files in WMP, not loading .mov files in Windows Live Movie Maker. What am I missing?

  - by royatl

  My friend needs to create a video and she has some source files that are .MOV format. I assume they are h.264. She can view the files with QuickTime. She has a laptop running Vista, and a just-downloaded version of Windows Live Movie Maker (which I'll call LMM for short). LMM shows an 'X' icon when she tries to add one of these files to it. My machine runs Windows 7 Pro, and a slightly earlier build of LMM and has no problems editing video with these source files. I assume she's missing a codec but what can I tell her? I've looked at the answer that mentions a QuickTime DirectShow Source Filter Plugin. It mentions only playback through WMP, not editing via LMM, but is that what she needs? I didn't have to load anything like that. That project's now done (she punted and used iMovie on a Mac). But I did gain another clue. She could play a 720p .MOV file, but these were 1920x1080 files.

  Read the article

• How do I format a text file for IIS Mailroot Pickup so that it sends an e-mail with attachments?

  - by Ben McCormack

  How do I need to format a text file so that it can be read by an SMTP service to send an e-mail that has an attachment? We have a server where we are using II6 SMTP to send mail from a Pickup folder. The goal is to drop a properly formatted text file into Mailroot\Pickup and then the file will be automatically processed and sent to the correct SMTP recipient. For simple files, this works correctly. Here's an example of a simple file that works (domain names changed): From:[email protected] To:[email protected] Subject:Hello World! Test Body Of The E-mail When I drop a text file containing the above contents into the Mailroot\Pickup folder, it sends correctly. However, I haven't been able to figure out how to get an attachment to work. I found some material that explained how to encode an SMTP attachment and another tool for simple base64 encoding conversion. Using the information on those pages, I came up with the following text: From:[email protected] To:[email protected] Subject:Hello World! MIME-Version: 1.0 Content-Type: text/plain; boundary="Attached" Content-Disposition: inline; --Attached Content-Transfer-Encoding: base64 Content-Type: text/plain; name="attachment.txt" Content-Disposition: attachment; filenamename="attachment.txt" VGhpcyBpcyBhIHRlc3Qgb2Ygc29tZXRoaW5nIHRvIGVuY29kZS4NCk5ldyBsaW5lDQpOZXcgTGlu ZQ0KIkhlbGxvdyIgISEhDQo9PT09ICcgZnNkZnNkZiAxMjM1NDU2MzQzNA== --Attached-- However, when I place the above text in a file and drop it into Mailroot\Pickup, it doesn't send an attachment correctly. Instead, an e-mail shows up with the following in the body of the e-mail: MIME-Version: 1.0 Content-Type: text/plain; boundary="Attached" Content-Disposition: inline; --Attached Content-Transfer-Encoding: base64 Content-Type: text/plain; name="attachment.txt" Content-Disposition: attachment; filenamename="attachment.txt" VGhpcyBpcyBhIHRlc3Qgb2Ygc29tZXRoaW5nIHRvIGVuY29kZS4NCk5ldyBsaW5lDQpOZXcgTGlu ZQ0KIkhlbGxvdyIgISEhDQo9PT09ICcgZnNkZnNkZiAxMjM1NDU2MzQzNA== --Attached-- I can't figure out what I need to do to format the text file so that the SMTP service correctly sends attachments.

  Read the article

• Different network response for indentical co-located machines

  - by Santosh

  We have a situation as follows: We have a two different virtual machines (VMs) on some remote server farm. The machines are identical in terms of hardware/software(OS) configurations. We have a J2EE application running on JBoss on each of those two machines. These two applications are of different version sav V1 on VM1 and V2 on VM2. We observed some degraded response time for application V2 when accessed via public URL. When we accessed the application through a secured VPN, there is hardly any difference. The bandwidth test (upload/download speed, ping etc) shows that VM1 is responding better when accessed via secured VPN. We concluded that the application does not seem to have performance issue. Because, it that's the case the performance degradation should also be there when access via VPN. So we concluded its the network problem. But since those two identical VMs are on same network we are looking for the reasons for different responses. My question is, given the above situation, what could be reasons for such a behavior ?

  Read the article

• SELinux blocking Samba directory listing

  - by Sean M

  I am running Samba on a CentOS server, and I am experiencing a problem where it allows me to connect to the server and see a share, but shows the share as an empty directory. I find this behavior strange. Here is the stanza in my smb.conf for the given share: [seanm] path = /home/seanm writeable = yes valid users = seanm, root read only = No Here's what I see on the server side: [seanm@server ~]$ ls -l -rw-r--r-- 1 seanm seanm 40 Jan 4 13:45 pangram.txt And yet: [seanm@client ~]$ smbclient //server/seanm -U seanm -W WORKGROUP Enter seanm's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.33-3.29.el5_5.1] smb: \> ls . D 0 Fri Jan 7 10:08:55 2011 .. D 0 Fri Jan 7 07:58:31 2011 58994 blocks of size 262144. 50356 blocks available This behavior is present on both a Windows client and a Linux client system. The behavior is present with the firewall on and with the firewall off, so it's not that. Neither /var/log/messages nor /var/log/secure have any complaints about Samba. I doubt that SELinux is a problem: just in case, here are the relevant settings. [root@server ~]# getsebool -a | grep samba samba_domain_controller --> off samba_enable_home_dirs --> on samba_export_all_ro --> off samba_export_all_rw --> off samba_share_fusefs --> off samba_share_nfs --> off use_samba_home_dirs --> on virt_use_samba --> off What am I doing wrong here, and what can I do to fix it? Edit: SELinux probably is the problem, judging by the fact that the issue goes away when I set SELinux to "permissive" or issue setsebool -P samba_export_all_rw on - both of which are unacceptable for production environments. What the heck kind of context does a directory need to have on it for Samba users to actually get files from it? I consider rolling your own rules and/or context to be deeply sub-optimal.

  Read the article

• TV won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• SATA Blu-Ray drive not detected via USB adapter

  - by LTR

  I'm using an SATA blu-ray drive (Lite-On IHOS104), connected via a USB adapter to my Windows 7 (32-bit) notebook. The first time I plugged the adapter in, it worked perfectly. The drive appeared in Explorer, and my player software was able to play an encrypted Blu-Ray disc just fine. After the first reboot, it never worked again. Now it shows up as "removable media" with a size of 0 bytes, irregardless of whether a disk is inserted or not. The drive does not show up under the green "eject USB device" icon in the taskbar. The adapter is powered using a separate power adapter. I have tried: disconnecting all other USB devices testing with a DVD instead of a Blu-Ray disc letting Windows search for updated drivers for the drive - there are none using the same drive and adapter on another Win7 (but x64) computer. They work perfectly. using other USB ports on the same notebook - tried them all. using a different SATA/USB-adapter What else can I do to diagnose this problem?

  Read the article

• "Safely remove hardware"...doesn't.

  - by Kev

  I have an external USB harddisk that I have scripted to safely shut down after a backup, so the backup operator can unplug it, and knows not to if the lights are still on for some reason. It's always worked fine using the DevEject command-line utility. This week it failed for some reason: DevEject 1.0 2003 c't/Matthias Withopf Ejecting 'USB Mass Storage Device' [USB\VID_0411&PID_002A\00000704C8D2]...FAILED (23,5) Error ejecting device USB Mass Storage Device, vetoed (15,5)! Worse yet, using the SRH tray icon, I click Stop, click OK, it pauses about 5 seconds with OK and Cancel greyed out, closes the sub-window, and then the main window with the Stop button still shows the device, and Stop is still available. I can keep doing that and it never gets rid of the device. I can still access it in Explorer. LockHunter reports that nothing is locking the drive. I've made no changes to the backup configuration or anything to do with the drive this week. Why the sudden flake-out? Short of a restart, which I can't do today before the backup operator goes home, how do I fix it?

  Read the article

• URL sniffer/downloader

  - by Ricket

  Some websites have Flash content that plays music or videos. Most of the time they don't show you the URL of these music or videos, but for example, you can sniff a YouTube webpage and find the flv file that YouTube is actually requesting and playing. Right now I'm using Orbit Downloader, which has a feature called Grab++ that does just this; you start it, and then you refresh the page, and it shows you all files of certain types (image, audio, video) that the webpage requests, and then you can select one or more and download and it downloads them. But, I don't like Orbit, it installs plugins and has the whole download manager thing which I don't really want. What is a good alternative program? I'm not looking for websites like kickyoutube.com, I want a URL sniffer I guess. HTTPGuideDog used to be my Firefox add-on that did exactly this, but it hasn't been updated even to FF3 (and yes I know I can hack it to load anyway, I'm looking for something natively available preferably). I vaguely know of WireShark but last time I used it, I believe it captures individual packets, which is a little too fine-tuned for me. I just want to be able to see what's happening, and download something that the webpage downloaded. Oh, and I'm using Windows 7. Linux probably has some fancy command-line tool, but it just won't cut it for me. :-\ Edit: Oh, and something free please. Feel free to mention paid solutions though.

  Read the article

• Cacti is ignoring hash marks in interface aliases

  - by Matt Simmons

  I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

  Read the article

• File in use when it's really not

  - by C-dizzle

  I am running Windows 7 Professional 32 bit on a Server 2008 network. I am getting a weird issue with an excel document where I open it up one morning, update it, save and close, the next morning I come in, open it up and it says "This file is in use and locked by csmith" which "csmith" is me! So I click on the cancel button, open it up again and it comes up fine. I can edit, save and close with no problem. But then have the same issue the next morning. Another weird thing is that we have a calendar shared in "Public Folders" under Outlook that seems to be having the same issue, which happens to be a calendar made in Excel. Exchange 2010 is installed on the server and the clients are using Exchange 2007. In the instance with the calendar, it will show conflicting edits have been made and you must keep one item or all items. And it shows an edit date of 4/24/2012 and 6/1/2012. But, there were NO edits done on 6/1, just tried opening it. This problem does not occur under my profile, but 2 others. These machines are ALSO running Windows 7 Professional 32 bit. We have a mix of Windows 7 and Windows XP machines on our network if that is any help. These issues did not start happening until we migrated from a server running Server 2003 and Exchange 2000, which the new server is running Server 2008 and Exchange 2010 as stated above. Is there something on the server side that is configured wrong?

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• Windows 2003 R2 zip program blocking EXE file

  - by Harvey Kwok

  I have a Windows 2003 R2 Enterprise Edition SP2 32-bit machine with all latest patch (as of 1-6-2011). It's a VM. I have a zip file, including a pdf file, a txt file and a exe file. If I copy the zip file onto the machine via a shared network drive, I can unzip all the files properly without problems. If I put the zip file on my web server and then I download it from there, I can only unzip the pdf file and txt file. The exe file is silently ignored. I searched the web and found somebody reporting similar issue on XP. If I right click on the zip file downloaded from the web server, at the bottom of the general page, it has a warning message saying that "This file came from antoher computer and might be blocked to help protect this computer" I understand that I can solve the problem by simply clicking the "Unblock" button and extract the file again. The things that bothering me is that why the warning message says "might be blocked"? I tried downloading the same zip file from the same web server on to my Windows 7 box with latest patch. It also shows the same warning message. However, even with the warning message, I can extract all the files properly without clicking the "Unblock" button. Is it a bug in Windows 2003 R2 SP1? Is there any security settings controlling this? How likely will the end user seeing this problem? I want to dig into this because I am worrying people downloading my zip file from my web server might see similar problems. The first thought coming to the user's mind will be the zip file is somehow corrupted. Honestly, I didn't know this "Unblock" feature in Windows before I run into this problem. EDIT I just tried it on another Windows 2003 R2 SP1 machine. The zip program doesn't block the EXE file on that machine either. Both Windows 2003 R2 SP1 machines are joining to the same forest.

  Read the article

• Apache MaxClients doubt

  - by Milan Babuškov

  I have a busy Apache server serving only dynamic PHP+MySQL pages. It is a prefork Apache, version 2.2.4 with following config: KeepAlive off StartServers 8 MinSpareServers 32 MaxSpareServers 64 ServerLimit 512 MaxClients 512 MaxRequestsPerChild 4000 MaxClients/ServerLimit used to be set to 256, but I got the following error in error_log so I increased it: [error] server reached MaxClients setting, consider raising the MaxClients setting It seems to work now, but I have a doubt. Looking at MySQL log of queries, I have a couple hundred clients per seconds, but "ps ax" only shows 8, 9 or 10 processes running: [root@engine ~]# ps ax | grep http | wc -l 10 I even got this many processes when the above error message was shown in error_log. This made me investigate further. When I run netstat -a, I get something like this: tcp 0 0 engine:http adsl-105-143.teol.net:21453 TIME_WAIT tcp 0 0 engine:http 118-36.static.kds:mck-ivpip TIME_WAIT tcp 0 0 engine:http 118-36.static:oce-snmp-trap TIME_WAIT tcp 0 0 engine:http 118-36.static.kd:unifyadmin TIME_WAIT tcp 0 0 engine:http cable-188-2-25-29.dyna:4906 TIME_WAIT tcp 0 0 engine:http adsl-105-143.teol.net:21458 TIME_WAIT tcp 0 0 engine:http 109-92-83-91.dynamic.:62821 TIME_WAIT tcp 0 0 engine:http cable-89-216-142-192.:63576 TIME_WAIT tcp 0 0 engine:http 109-92-83-91.dynamic.:62819 TIME_WAIT tcp 1081 0 engine:http pttnetadsl38-36.ptt.r:50496 ESTABLISHED tcp 0 0 engine:http cable-188-2-36-196.dyn:4136 TIME_WAIT tcp 0 0 engine:http cable-89-216-142-192.:63580 TIME_WAIT tcp 0 0 engine:http cable-89-216-142-192.:63581 TIME_WAIT etc. When counting those, I get: [root@engine ~]# netstat -a | grep http | wc -l 431 Can anyone tell me what is really going on here and how to make sure my server keeps working, because I only use 50% of available RAM in machine?

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• PHP memory_limit local value does not match php.ini value

  - by Buttle Butkus

  CentOS system. Summary: changed memory_limit in master and local php.ini and yet no change in the local value for a particular virtual host. Trying to improve performance, I set the memory_limit to 1024M in /etc/php.ini phpinfo() shows Master and Local values for other virtual hosts on the server as 1024M. Changing the value in /etc/php.ini changes all values, except one. One site is stuck with a local value of 256M. I thought I found the problem: there is a php.ini file (which I didn't know about) in that site's root, and it had memory_limit = 256M I changed it to 1024M. Problem solved? No. And now I don't know where to look. Obviously, I've restarted apache (/etc/init.d/httpd restart), and that usually does the trick. I also turned off APC cache, though I don't think it would cache ini files. And finally, I tried adding this to the virtual host in httpd.conf: php_value memory_limit 536870912 (yes, that would be 5 GB) And that had no effect whatsoever. What else could be the problem? Thanks.

  Read the article

• Website cannot be accessed with google DNS because of unsigned DNS

  - by Sinan Samet

  I get this error: Inconsistent security for stakeholdergame.com - DS found at parent, but no DNSKEY found at child. On http://dnscheck.pingdom.com/?domain=stakeholdergame.com People can't access my site with google public DNS because of this. How do I solve this problem? dig @ns1.haveabyte.nl stakeholdergame.com DS shows me this ; <<>> DiG 9.8.3-P1 <<>> @ns1.haveabyte.nl stakeholdergame.com DS ; (1 server found) ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 42223 ;; flags: qr aa rd; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 0 ;; WARNING: recursion requested but not available ;; QUESTION SECTION: ;stakeholdergame.com. IN DS ;; AUTHORITY SECTION: stakeholdergame.com. 14400 IN SOA ns1.haveabyte.nl. hostmaster.stakeholdergame.com. 2014030300 14400 3600 1209600 86400 ;; Query time: 21 msec ;; SERVER: 79.170.93.174#53(79.170.93.174) ;; WHEN: Tue Jun 10 11:20:41 2014 ;; MSG SIZE rcvd: 100

  Read the article

• Problem with mydomain.com no prefix

  - by user10711

  Short question is. I have a domain name mydomain.com, we have a company website hosted on an IIS server 2003 configuration. Going to the address bar and typing www.mydomain.com will show my website properly. Typing mydomain.com into the same address bar will return an under construction website that seems to be hosted on my webserver. My domain name is hosted by Network Solutions, and I think I have it configured correctly using their advanced DNS services. In their settings I have www.mydomain.com, * and @ also pointed to the ip address of my webserver. On my webserver itself using the IIS manager, under the Web Site, and Web Site Identification. I have configured both www.mydomain.com and mydomain.com configured to work on the IP address on the webserver. I am hosting 4 different websites on my IIS server, all the other sites use prefixes other than www, an example is mail.mydomain.com and a couple of others. None of them show an under construction page as their default homepage. I am really at a loss as to why it would show an under construction page, especially since it seems to be pointing to the correct server. The reason this is such a big deal is because when you search for my company on google, the link there is for mydomain.com and by clicking on the link it shows under construction which is really quite embarrassing. Thanks in advance for any help and if there are further questions let me know.

  Read the article

• How to forceably unmount stuck network share in Mac OS X?

  - by Kyle Lowry

  Not long ago my Xserve failed (power loss) while an iMac was working with files on a particular network share (called "Work Share"). This volume, "Work Share", is now stuck. It can't be seen in the GUI, you can only detect it using the Terminal. Even after power cycling over the course of several days, ls -a still shows that it's there, but I can't unmount it using any command - not even as root in single user mode. Every time I attempt to unmount that volume, I get the message that the resource is busy (which it can't possibly be since nothing is using it), and error code 4915. The issue is that when I mount the real "Work Share", it internally is renamed to "Work Share-1", which breaks all my links, and several files in the share. If I can't unmount the false "Work Share", then that computer would be unuseable without a reformat, I would imagine - and I don't want it to have to come to that. I've tried everything I can think of - it looks like sudo can't save me now. Any ideas on how to unmount this stuck volume?

  Read the article

• Forwarding HTTP Request with Direct Server Return

  - by Daniel Crabtree

  I have servers spread across several data centers, each storing different files. I want users to be able to access the files on all servers through a single domain and have the individual servers return the files directly to the users. The following shows a simple example: 1) The user's browser requests http://www.example.com/files/file1.zip 2) Request goes to server A, based on the DNS A record for example.com. 3) Server A analyzes the request and works out that /files/file1.zip is stored on server B. 4) Server A forwards the request to server B. 5) Server B returns file1.zip directly to the user without going through server A. Note: steps 4 and 5 must be transparent to the user and cannot involve sending a redirect to the user as that would violate the requirement of a single domain. From my research, what I want to achieve is called "Direct Server Return" and it is a common setup for load balancing. It is also sometimes called a half reverse proxy. For step 4, it sounds like I need to do MAC Address Translation and then pass the request back onto the network and for servers outside the network of server A tunneling will be required. For step 5, I simply need to configure server B, as per the real servers in a load balancing setup. Namely, server B should have server A's IP address on the loopback interface and it should not answer any ARP requests for that IP address. My problem is how to actually achieve step 4? I have found plenty of hardware and software that can do this for simple load balancing at layer 4, but these solutions fall short and cannot handle the kind of custom routing I require. It seems like I will need to roll my own solution. Ideally, I would like to do the routing / forwarding at the web server level, i.e. in PHP or C# / ASP.net. However, I am open to doing it at a lower level such as Apache or IIS, or at an even lower level, i.e. a custom proxy service in front of everything. Thanks.

  Read the article

< Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >