Search Results

Search found 13947 results on 558 pages for 'television shows'.

Page 394/558 | < Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >

• How harmful is a hard disk spin cycle?

  - by Gilles

  It is conventional wisdom¹ that each time you spin a hard disk down and back up, you shave some time off its life expectancy. The topic has been discussed before: Is turning off hard disks harmful? What's the effect of standby (spindown) mode on modern hard drives? Common explanations for why spindowns and spinups are harmful are that they induce more stress on the mechanical parts than ordinary running, and that they cause heat variations that are harmful to the device mechanics. Is there any data showing quantitatively how bad a spin cycle is? That is, how much life expectancy does a spin cycle cost? Or, more practically, if I know that I'm not going to need a disk for X seconds, how large should X be to warrant spinning down? ¹ But conventional wisdom has been wrong before; for example, it is commonly held that hard disks should be kept as cool as possible, but the one published study on the topic shows that cooler drives actually fail more. This study is no help here since all the disks surveyed were powered on 24/7.

  Read the article

• Enable Soap for PHP 5.5.x on CentOS 6.5

  - by Chris Mancini

  Unfortunately I have to support soap on my server for the Fedex webservice. I recompiled PHP enabling support and it works via CLI but not PHP-fpm. They both point to the same ini file and both show the module loaded, but only CLI shows the configuration values. Output of php -i | grep -i soap Configuration File (php.ini) Path => /usr/local/etc Loaded Configuration File => /usr/local/etc/php.ini Configure Command => './configure' '--prefix=/usr/local' '--with-config-file-path=/usr/local/etc' '--with-config-file-scan-dir=/usr/local/etc/php_user/' '--enable-fpm' '--enable-ftp' '--enable-libxml' '--enable-mbstring' '--enable-pdo' '--enable-soap' '--enable-sockets=shared' '--enable-zip' '--with-curl' '--with-fpm-group=nginx' '--with-fpm-user=nginx' '--with-freetype-dir=/usr/lib64/' '--with-gd' '--with-jpeg-dir=/usr/lib64/' '--with-libdir=lib64' '--with-mcrypt' '--with-openssl' '--with-pdo-mysql' '--with-pear' '--with-readline' '--with-tidy' '--with-xsl' '--with-zlib' '--without-pdo-sqlite' '--without-sqlite3' soap Soap Client => enabled Soap Server => enabled soap.wsdl_cache => 1 => 1 soap.wsdl_cache_dir => /tmp => /tmp soap.wsdl_cache_enabled => 1 => 1 soap.wsdl_cache_limit => 5 => 5 soap.wsdl_cache_ttl => 86400 => 86400 Output from php-fpm phpinfo(): Configuration File (php.ini) Path /usr/local/etc Loaded Configuration File /usr/local/etc/php.ini SOAP Brad Lafountain, Shane Caraveo, Dmitry Stogov Please help, I have tried so many things...

  Read the article

• AuthBasicProvider: failover not working when the first LDAP is down?

  - by quanta

  I've been trying to setup redundant LDAP servers with Apache 2.2.3. /etc/httpd/conf.d/authn_alias.conf <AuthnProviderAlias ldap master> AuthLDAPURL ldap://192.168.5.148:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> <AuthnProviderAlias ldap slave> AuthLDAPURL ldap://192.168.5.199:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> /etc/httpd/conf.d/authz_ldap.conf # # mod_authz_ldap can be used to implement access control and # authenticate users against an LDAP database. # LoadModule authz_ldap_module modules/mod_authz_ldap.so <IfModule mod_authz_ldap.c> <Location /> AuthBasicProvider master slave AuthzLDAPAuthoritative Off AuthType Basic AuthName "Authorization required" AuthzLDAPMemberKey member AuthUserFile /home/setup/svn/auth-conf AuthzLDAPSetGroupAuth user require valid-user AuthzLDAPLogLevel error </Location> </IfModule> If I understand correctly, mod_authz_ldap will try to search users in the second LDAP if the first server is down or OpenLDAP on it is not running. But in practice, it does not happen. Tested by stopping LDAP on the master, I get the "500 Internal Server Error" when accessing to the Subversion repository. The error_log shows: [11061] auth_ldap authenticate: user quanta authentication failed; URI / [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server] Did I misunderstand?

  Read the article

• Why is .htaccess not allowed in a directory but is allowed in another?

  - by JD Isaacks

  I have apache2 installed on ubuntu 10.4 inside my var/www/ directory [amung others] I have a cakephp and a dvdcatalog directories. Each of which have CakePHP 1.3 installed. I can access them both via localhost/cakephp and localhost/dvdcatalog But the dvdcatalog shows up with no css styling. They both have these files: /var/www/cakephp/app/webroot/css/cake.generic.css /var/www/dvdcatalog/app/webroot/css/cake.generic.css But when I go to http://localhost/cakephp/css/cake.generic.css it sees the file but it does not see the file when I go to http://localhost/dvdcatalog/css/cake.generic.css I think this means the cakephp folder is able to use .htaccess and the dvdcatalog is not. I setup the cakephp directory last month when I was following in the blog tutorial. I am setting up the dvdcatalog directory now for a different tutorial. So I am not sure if I am missing a step. in my /etc/apache2/apache2.conf file I have this: <Directory "/var/www/*"> Order allow,deny Allow from all AllowOverride All </Directory> Which I thought gave .htaccesss to all. Does anyone have any ideas what the problem is?

  Read the article

• Robocopy launches and then hangs/just sits there

  - by NateO

  I'm setting up an archive process to store old files on an external hard drive. The computer in question is running Windows 7 Pro 32bit. We have a server folder with 150,000+ files in it, most of which are pretty small (below 200k). I'm trying to use robocopy in a batch file to do this. It was working fine the other day, now all it does upon launch is sit there. It shows me all the options and whatnot, and also lists the number of files in the directory and the directory itself, but it never gets past that line. If I switch the destination to the local C drive, it eventually starts copying files. Is there something in my batch file that needs to change? Or could there be a problem with the external Western Digital drive that I'm using? The WD drive currently is holding about 175,000 files. Here is the one line batch file I have: robocopy "\\cgifp01\Prepress\Public\ImportedPDF" "E:\OldFiles" *.* /R:2 /W:10 /MINAGE:15 /MOV /B /XJ /XF "blank_test.pdf" Thanks for any tips or ideas. Nate

  Read the article

• online backup plan for a home office with servers

  - by TiernanO

  So, i am in the process of tweaking my spending and i need to change my backup plan... I am currently using a mix of JungleDisk and ZManda ZCB to backup files on my MacBook Pro, Main Windows Server Wrokstation, a dedicated Windows Server in a datacenter, and various other machines and file sources. The problem is the cost: this month, it has cost me about $90 to backup a little over 500Gb... This amount of data will increese over time too, since i am backing up Photos (24Mb RAW images + 4-8MB JPEGs), Videos (various cameras shooting 720p and 1080p), Music, Movies, TV shows and Apps from iTunes (though with iTunes cloud, this might not need to be backed up again) and source code... I have looked at the likes of Mozy, CrashPlan+ and Pro, Backblaze and Carbonite, but each have their problems: Mozy seems overly expenvice per gig at 50C Crashplan wont sell to me since i am outside the US (they hide it on their site... hidden in the FAQ section!) Backblaze dont support Windows Server Carbonite business pricing is $600 up front for 500Gb of storage... Fro $229, they will not backup Windows Servers. So, other than those, Jungle Disk (at 15c per Gig) or ZManda (also at 15c per Gig) what other options are there? what are other people using?

  Read the article

• Sql Server 2005 database lost, How to recover all records. MDF/LDF size is same as it should be

  - by Shantanu Gupta

  Few months back, I installed a sql server 2005 on one of my client machine. I gave him a backup option to take backup timely but he never took any backup. Today he called me that "i m not able to see any record of mine." I visited at my clients system and saw that none of the record was present on the tables. There was not even a single row in any of the tables. Then I checked if he has any backup file which i found to be absent. I asked him the reason what could be the possible cause. He said it might be due to virus. After this I checked the size of mdf and ldf file and found it should be what it is. when i created his server mdf ldf file had 2MB of database now it is 83 MB and 193Mb mdf/ldf respectively. This shows the data is still present in it but it is not being displayed. What could be the possible cause and how can i restore all data back to my tables ?

  Read the article

• How to monitor changes in the frequency of network latency spikes over time?

  - by dequis

  I'm currently trying to troubleshoot an issue with my network in which I get latency spikes up to 200 seconds (normally around 50 secs) in an apparently random way at apparently random moments of the day. While trying to find what part of my messy network needs to be blamed (outside of the scope of this question - discussed a bit on chat), I realized I have no reliable way to confirm that a change actually improved anything. So far, the main way in which i notice this is that irssi shows [Lag: 15 (??)] in the statusbar, increasing every 5 seconds, and all other connections seem to be affected too. Since this depends on my observations, it's not a very reliable method to know how often it really happens. Note that just sending ICMP pings is probably not enough, but that's just my guess. It might be a "bufferbloat" issue, it might be packet loss, it might only apply to persistent connections. I suspect this because a few months ago, when the issue started, I had a "ping" command running in background and it didn't show anything weird at all during the latency spikes. This seems to have changed now (pings don't go through), but still, I'd prefer something more robust.

  Read the article

• Win8/7/XP print spooler not getting along with Zebra ZT230 via WIFI

  - by Jonathan M

  I have a graphics-intensive 4"x6" label I'm printing to the ZT230. I'm printing multiple (10) copies. When connected via USB, all goes well. However, when connected via wifi, I only get 2 of the labels. A wireshark capture shows that at some point in the process my computer (presumably my windows spooler) is sending a reset packet, which, I believe, would pretty much kill the print job. I'm getting the same results on Win8, Win7 and WinXP. The print job was originally generated on Zebra's ZebraDesigner2 software. For easier diagnosis, I captured it to a .prn file. The .prn file can be found here: https://drive.google.com/file/d/0BwxF_9SAkKzLLTF5bUJVT0lESUU/edit?usp=sharing And the wireshark capture file can be found here: https://drive.google.com/file/d/0BwxF_9SAkKzLTGpSS0ktZW1xV28/edit?usp=sharing And the printer configuration listing: https://docs.google.com/document/d/1zh1Tw4D4yNa2uljOIL1kO2z8se9HK859irpUEwyxlyY/edit?usp=sharing I've started a discussion with Zebra Tech Support, and they're working on it, but I thought I'd toss it out here for more ideas since we're getting kind of stumped. Any ideas why this may be happening?

  Read the article

• Usb device not working properly on a Thinkpad T60

  - by Xavierjazz

  I have just started getting a message that a USB device is not working properly. This is on a new Thinkpad T60 running Windows XP Professional SP3. I have had all devices attached for about 10 days or so. When I go to device manager there is no sign of a problem: everything is working correctly. I am unable to find out which device it is. I searched this forum but the only reference I found was to older computers which may not be Usb2 capable. This is not my problem. Any ideas? Thanks. EDIT: I realized I had a harddrive attached but turned off. Although I could not track down any error messages except the balloon that came up, I have disconnected it and, so far, no messages. We'll see over the next day or two, but this may be the problem. Thanks EDIT: This has not solved the problem. I get the message that one of the USB devices has malfunctioned and it points to "USB root hub (2 ports)" and shows an unused port and an unknown device. However, when I check my device manager, it says that there are no problems, everything is working as it should. ?? EDIT: I now found the event log view and there are 2 types of error messages. They do not relate to the time that I get the balloon. 2 of the 3 are "Ati2mtag" errors and the third is "System Control Manager". Are these related to my problem, and the balloon just pops up randomly? EDIT: well, I'm still having the problem, and have narrowed it down to a malfunctioning device. Thanks to all.

  Read the article

• Struggling to set-up NLB cluster

  - by Chris W

  I'm trying to set up NLB on a couple of Windows 2008 R2 virtual servers running on top of Hyper V R2. The servers each have a single vNIC for LAN access (and a second vNIC for SAN access). I'm setting up the cluster to use Multicast mode. The vNICs are each set to allow MAC spoofing. Essentially I'm finding that i can add SERVER1 as a host and it will pick up and respond to the cluster IP from a remote subnet. If I then 'stop' the node in NLB manager it still responds when I would expect it to stop answering on that IP. If I recreate the cluster and add SERVER2 as the first host, the wizard completes correctly and an IPCONFIG on the server shows that it now has the cluster IP but I can't ping the cluster IP from a remote subnet but I can from another machine on the same subnet. As a final test - with both servers in the cluster, pinging from another machine on the same subnet I still get a response from the cluster IP when both nodes are stopped according to the NLB manager. The two VMs are sat on the same physical blade and are built up exactly the same as they'll be used as SharePoint web front end servers. I'm at a loss as to what could be wrong with the second VM that prevents it taking on the address just as the sole node in the cluster, never mind the strange behaviour of the cluster when I stop/start nodes.

  Read the article

• Tool to modify properties/metadata of a PDF? i.e. Change "Title", "Author"? Sony Reader showing som

  - by Chris W. Rea

  I own a Sony Reader PRS-600 ebook reader. I bought a ton of Manning Publications ebooks (DRM-free) recently. Many of the books are PDFs since not all the ones I wanted are available in epub format. The problem: Some of the PDF books I purchased have incorrect or missing metadata. Making things worse, the Sony Reader only displays the "Title" from the PDF metadata when displaying book titles in the reader's collection of books! The Reader doesn't display the filename. So, even though I have a PDF informatively named "Windows PowerShell In Action.pdf", it shows up as "untitled" in the Reader. Imagine how useful the Reader's list of book titles becomes when many are just "untitled" or "unnamed document" ! Yes, it is maddening. So – short of expecting the publisher to fix the files or Sony to add a filename-based list instead, I'm looking for a way to fix the PDF metadata. I can view the metadata with Adobe Reader, but it doesn't permit modification of the properties. Leading to: Question: Is there a tool – free, or cheap – and either for PC or Mac, that can modify the properties / metadata of a DRM-free PDF document? I want to correct "Title" and "Author" fields, specifically.

  Read the article

• Pivot tables: How can I total the subtotal?

  - by Mike

  Person A needs £115, Person D £234 and Person G £789, but how do I SUM that and get it to show on the same ROW as the subtotal? The Rows are subscription names. The Value field holds the Cost per subscription. the Columns holds the name of the person who receives the subscription. I have GROUPED on YEAR & MONTH, and have a subtotal that shows me how much each person will need to pay each month for all their subscriptions, but I need a figure showing me the total of all the subscriptions per month. I've tried adding calculated fields, but I want to SUM the subtotals so I'm struggling to see the field I need to use. I've tried Grand Totals but that SUMS all rows and I really only want SUM the Subtotal Total Row. I need a nice neat report that my managers won't go white at when looking at it...to many numbers = fear and confusion. Anyway it got messy, so I've come for help. Cheers Mike.

  Read the article

• Driver issue for 7850 HD Diamond Windows 7

  - by Mr.Student

  I have an issue with windows 7 implementing the drivers ati provides for my 7850 HD Diamond video card. The video card is plugged in correctly to the PCIE 2.0 slots of my motherboard (p6t asus) with more then enough power. Fortunately the card works as I have my monitor plugged into the card itself and I can see just fine. However windows 7 does not replace the standard vga default microsoft driver with catalyst drivers that I've tried installing from online as well as the CD. Every time I install the drivers using Catalyst Install manager it always finishes with "Install complete(Warnings occured)". I then see the warnings it has which it instead reports that it successfully installed the SDK, Catalyst Install Manager, and HDMI/AUDIO packages. When I check my device manager after that, the display adapter still shows as standard vga and that its still using microsoft default display adapter. Now this current card is replacing an old card of mine which is the ATI 4890 HD which works beautifully. In fact for the old card to work, all I need to do is go to device manager and right click on standard vga - click update driver and windows 7 magically finds the correct driver to install and everything is good. Not so with the new card. I've even went into my regedits and uninstalled every bit of ati driver software before reinstalling my new card. Nothing's worked thus far. I've already exchanged my card out once and talked to customer support from my motherboard, microsoft, and ati all blaming the other. Please help me out!!

  Read the article

• How do I connect a 2008 server to a 2003 server active directory?

  - by Matt

  Our DC is running Windows Server 2003. I've just set up Windows Server 2008 and have terminal server running on it. When setting the terminal server permissions, it was able to allow a group name that was read from the domain. In the DC the new terminal server shows up as a computer in the domain. I can also log in as a user within the domain even though that user doesn't exist locally on the new server. However, when I go to set sharing permissions on the new machine it doesn't show my domain as a location. Instead it is only looking at location "machinename" and not allowing domain to be seen or added. Is there something I'm missing? Ok, lots of errors in the event log. We have this: The winlogon notification subscriber is taking long time to handle the notification event (Logon). Followed by this: The winlogon notification subscriber took 121 second(s) to handle the notification event (Logon). Followed by: The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has succesfully processed. If you do not see a success message for several hours, then contact your administrator. I think this might be the same problem I'm having http://serverfault.com/questions/24420/primary-domain-controller-slow Solved. The issue was that I had changed from DHCP to static and put the wrong DNS server IP in. i.e. firewall instead of DC/DNS server.

  Read the article

• How can I safely close this window and forever avoid seeing similar pop-ups from Mackeeper Zeobit's malware and spyware?

  - by Michael Prescott

  The attached image shows a window that just popped up and the only button available is the OK button. I could Force quit Safari, but I've got several sites open right now and don't want to try and find my place again. Besides, I've seen similar hacks in the past and I'd like to learn how to handle them in a way better than just a brute force-quit. I've never heard of MacKeeper or Zeobit, so I opened Firefox and did a few searches while Safari is obviously still stuck, waiting for me to click the sneaky OK button in the dialog window. Anyhow, at least the first few pages of most search results contain lots of blabbering from questionable witnesses about how MacKeeper saved them from some malware or spyware. However, any company that is hacking the browser to maliciously install their product is itself the criminal and not providing a true security application. So, there are three questions here: How can I close this window? Can I do something to Safari to avoid these hacks in the future? (Just curious) Is MacKeeper or Zeobit somehow loading the search results so that no information about their application being malware or spyware is listed (I can't be the only person in the world that is offended by their tactics, even though it appears I am)?

  Read the article

• None of usb-controllers are working after a crash

  - by Cray

  So I have a GA-p35-DS4 mboard with a Q6600, running windows7-x64. After a random crash with a bluescreen (not caused by anything particular as I recall), none of the usb-controllers are working. (And none of the devices connected to those usb ports). All the controllers are showed up in the device manager, but every one has a warning-icon (as they are not functioning properly). The windows identifies them correctly, it shows exactly the model of each controller, and it says that the driver is installed. Now, when I try to reinstall the driver (Update driver menu item in the device manager), it tries to find it, finds the driver, but quits saying that the driver was found but could not be installed. Additionally, it displays "This operation requires an interactive window station", whatever that means... Now get this, the same thing happens with a new pci-usb controller card! It is found (actually each time the machine starts, it is found as new hardware), but trying to install drivers leads nowhere, I am getting the same message about an interactive window station. (tried to install drivers from the acoompanying CD) I have tried deleting those devices from device manager and let windows find them again, but that leads to same results. None of the ports on this extension card work either. This should not be a hardware problem, a usb keyboard connected to the builtin usb controller works in bios, and even in another OS running the same computer (old xp installation) What to do? Will I have to reinstall? Can deleting infcache.1 help? Is there some way to let windows remove all old drivers and try to find all hardware again, this time only looking for drivers on a windows install disk or something?

  Read the article

• Websites down EC2 inaccessible via SSH CPU utilisation 100% last few hours - what should I do?

  - by fuzzybee

  I have multiple websites hosted on 1 single EC2 instance. 1 website "abc" were down for a few hours, sometimes threw database connection error and sometimes just took too long to respond. 1 website "def" were incredibly slow but still up and running the rest of the websites had the same symptoms has "abc" I can afford 15 min or less down time for "def". Should I then (in AWS console) reboot my instance or create an AMI image from my instance and launch it and associate my elastic IP to the new instance or "launch more like this" Background on what may have happened to my ec2 The last time I made changes for 21 hours ago. A cronjob to create snapshots ran around 19 hours ago and it has been running for a long time. Google Analytics shows traffic to my websites such as kidlander.sg has been nothing exceptional. Is there any other actions I should take or better options I could have? (I have already contacted AWS support but their turnaround is 12 hours so I appreciate all the help I could get) Update I got everything back up and running and CPU utilisation back to normal, around 30%. There is 1 difference between "def" and "abc" as well as my other websites "def"'s database is hosted on RDS "abc"'s database is hosted on an EC2 instance (different from my web server instance) configured by myself Nevertheless, I checked the EC2 instance I'm using as MySQL server yesterday and it was absolutely fine during the incident low CPU ultilisation I could log in using linux command line

  Read the article

• Hard drive not correctly recognized on a new Windows 7 installation, but works correctly on Windows XP

  - by david

  I'm having problems configuring a hard disk in a brand new, clean Windows 7 installation. System specs: Hard disk: WD VelociRaptor WD6000HLHX (600 GB, 10000 RPM) Motherboard: Gigabyte Z77X-UD3H BIOS SATA mode set to AHCI (not RAID), with disk connected to SATA0 (6 Gb/s port). Windows 7 Enterprise SP1 64-bit The disk is recognized by the BIOS and is correctly identified, with the name and size correctly reported. Windows recognizes the disk itself and reports the device is functioning correctly, but it doesn't appear in Explorer. Disk Management shows the drive, but incorrectly states that it is uninitialized and has no partitions. If I try to initialize the drive, I get an error saying that "the system cannot find the file specified" (what file?). Before connecting the drive to the new machine, I partitioned and formatted it under Windows XP SP2, creating 2 partitions (MBR, not GPT) and copying over a boatload of data. However, none of this data appears under Windows 7. If I put the disk back into the Windows XP machine, I can access the disk and all of its data. Is it possible to get Windows 7 to correctly recognize the disk without having to erase it and start over? If so, how do I do so? I checked this question, which seems to cover the same issue, but it didn't help.

  Read the article

• MS DNS lookup issue

  - by 3molo

  Hi, Got two AD/DNS servers, and on the secondary I can't seem to lookup the external site www.iis.se (or any other hostname that their name servers control). The central firewall at this office allows any any outbound, tcp and udp. The DNS server has no local firewall nor antivirus. My windows client, located in the same subnet as the DNS server can do the lookup by asking the nameservers that are in control of www.iis.se. 'dig NS iis.se' shows iis.se. 2517 IN NS ns2.nic.se. iis.se. 2517 IN NS ns.nic.se. iis.se. 2517 IN NS ns3.nic.se. on AD/DNS server C:\Users\Administratornslookup www.iis.se 212.247.7.228 Server: UnKnown Address: 212.247.7.228 Name: www.iis.se Addresses: 2a00:801:f0:80::80 212.247.7.221 C:\Users\Administratornslookup www.iis.se 194.17.45.54 Server: UnKnown Address: 194.17.45.54 Name: www.iis.se Addresses: 2a00:801:f0:80::80 212.247.7.221 C:\Users\Administratornslookup www.iis.se 212.247.3.83 Server: UnKnown Address: 212.247.3.83 Name: www.iis.se Addresses: 2a00:801:f0:80::80 212.247.7.221 And still: C:\Users\administratornslookup www.iis.se Server: UnKnown Address: 127.0.0.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. * Request to UnKnown timed-out

  Read the article

• New hard drive for backup? [closed]

  - by glaeven

  I have come to realize that I need another external drive to use with my MacBook Pro. I currently have a 1TB WD MyBook Essential that I have been using for about a year and a half. I have it currently partitioned into two drives, one for backup (I named it Leonov) and one for movies, TV shows and other large files I don't need very often (I call that side Discovery One). I use Time Machine for backups since it is completely automated and I can restore from it without much trouble (I have had to at least three times now). As of now, Leonov is full enough that every backup deletes an old one and Discovery One is approaching it's limits. I would like to get a new drive and move one of the sides to it. What are some reliable, external (~1TB) drives for under or around $100? Would it be easier to move the movies (et al.) or the backups to the new drive? I also feel like I should say that all of my important documents (for school and the like, just not my music) are also synced to Dropbox as another form of backup and access.

  Read the article

• Can I have 2Gbit over 1Gbit Nics

  - by Daniel

  So this really baffles me. Apparently because 1Gbit can transmit data in both directions simultaneously it should be possible to get 2Gbit of data transfer on a single NIC (1Gbit flow seend and 1Gbit receive). People claim that because 1Gbit is full-duplex (almost always) it is exactly 2Gbit in total. My intuition and electrical background tells me that something is not right here 4 twisted pairs 250Mbit capacity each gives 1Gbit. Unless it is really possible to transfer data in both directions simultaneously. I did a test with iperf. Ubuntu server 12.04 <-- MacBook Pro. Both with decent CPU speed. Tested speed of connection individually and on Mac I can see 112MB/s regardless which direction data is going. On Ubuntu with vnstat and ifstat I got 970Mbit speeds. Now, launching iperf in server mode on both machines at the same time and sending data using 2 iperf clients shows that I'm for example on Ubuntu box sending at 600Mbit, and receiving 350Mbit. which adds up to pretty much 1Gbit link. So to me there is no magical 2Gbit. Can someone confirm that or tell why I'm wrong? Another thing that confuses me i the fact that e.g. 24-port switch has for example: Throughput»up»to:»50.6Mpps Switching»capacity:»68Gbps Switch»fabric»speed:»88Gbps Which would suggest thay can handle 2GBit per port.

  Read the article

• Varnish configuration, NamevirtualHosts, and IP Forwarding

  - by Brent

  I currently have a bunch of NameVirtualHost based websites, load balanced between 3 apache2 servers using ldirectord. I would like to insert varnish as a reverse-web-proxy between ldirectord and apache in the following way: a request comes in to ldirectord it is then load balanced between the 3 apache2 servers and varnish, with a weight of 1 for the webservers, and 99 for varnish (so if varnish is rebooted, the webservers will take over seamlessly) varnish will then load balance its requests between my apache2 servers. However, the varnish part is not working. I wonder whether this has to do with the fact that my apache servers use x.x.x.x:80 for their NameVirtualHosts, instead of *:80? (they have to do this, since each server hosts multiple IP addresses) Or perhaps it has to do with the need for IP Forwarding to be set up on the varnish server? (I did echo 1 /proc/sys/net/ipv4/ip_forward on this server, is that sufficient?) How can I debug this problem? ldirectord doesn't produce logs of what it does with each request (and if it did, I would be overwhelmed with information since I'm serving hundreds of requests per second) varnish log shows the ldirectord server connecting to it every 5 seconds, but nothing else. I have set up a test site using this configuration, but it fails - no apache access logs, no applicable varnish logs.

  Read the article

• How do I configure a new (non-OS) raid device under Windows 7?

  - by GregH

  I recently installed 3 new 1TB drives in my Windows 7 (64 bit) system. These are in addition to the 10k rpm disk that I already have running the Windows 7 OS. My intent is to create a RAID 5 volume with the 3 disks. I don't seem to have a problem configuring the bios and creating the resulting 1.9 TB RAID volume. I run in to the problem when I try booting in to Windows. I get a quick flash of a blue screen and then am prompted by windows to do a repair. It tries to repair and then reboots. This sequence lasts indefinitely. If I re-configure the bios back to non-RAID (ACHI) then windows boots fine. The strange thing is that the 1.9 TB volume I configured through the bios actually shows up in windows! Strange since the motherboard is not set up with RAID. I assume that I somehow have to install the RAID drivers from the mobo manufacturer. How do I do this? Is the reason I'm getting the blue screen a result of not having the RAID drivers installed? It's strange because I can find plenty of documentation on how to set up RAID and do a fresh install Windows on to the RAID device, but nothing on how to set up a RAID device on an already running system. Advice is appreciated.

  Read the article

• Debian apache2 restart fault after some updates

  - by Ripeed

  can anyone give me an advice with this please: I run update on my debian server by Webmin. After updating some apache2 and etc. It shows update fail. After that I cant start apache2. I must run netstat -ltnp | grep ':80' Then kill pid kill -9 1047 and now i can start apache2 When I started it first time after update some websites on fastCGI wont work I must change them in ISPconfig3 to mod-PHP and now works NOW - I cant restart apache without kill pid. In log of ISP I see Unable to open logs (98)Address already in use: make_sock: could not bind to address [::]:80 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down In log of some website I see [emerg] (13)Permission denied: mod_fcgid: can´t lock process table in pid 19264 Do you thing it will be solution update everithing by: apt-get update and apt-get upgrade to complete all updates? I have little scare if I do that then next errors will occur. If I look at apache log i see error: Debian Python version mismatch, expected '2.6.5+', found '2.6.6' But that was there before that problem before. Thanks A LOT for help.

  Read the article

< Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >