Search Results

Search found 123 results on 5 pages for 'e5'.

Page 4/5 | < Previous Page | 1 2 3 4 5  | Next Page >

• No video signal and server shuts down

  - by Ilya

  I have a brand new server. The motherboard is Intel S2600CP4, two 8-core Intel E5-2600 processors. RAM is 8 DIMM slots of 8 GB each (KVR1600D3D4R11SK4/32GI, I installed them into the blue slots), Power supply is 1050W Corsair. Most of the time the server won't start up - the fans are spinning, but I don't have video signal. And it keeps restarting on its own every 3 mins. But maybe after 30 mins it will eventually load and show something on the screen. I even was able to install ESXi 5.0 (vSphere) on it. It recognizes both CPUs and all of the 64GB of RAM. But even then it worked only for around 5 hours and then restarted on its own. What's the problem? That's a very expensive peace of hardware and I can't afford purchasing a new motherboard/CPU. By the way, on the front panel the "System Status" LED is constantly amber (not blinking), even when the server started successfully. And also in the BIOS I can see lots of "processor 01 unable to apply microcode update 8160" fatal errors. Please help me with issue, I will really appreciate this!

  Read the article

• Nginx + PHP-FPM Too Many Resources

  - by user3393046

  My Server has the following Specs CPU: 6 Cores Intel(R) Xeon(R) CPU E5-2650 v2 @ 2.60GHz RAM: 32 GB I have a problem with nginx+php-fpm. They are taking too many resources for an unknown reason. Even if i restart the nginx + php-fpm the start up processes will use many resources. My nginx Config is the following: user nginx; worker_processes auto; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; worker_rlimit_nofile 300000; events { worker_connections 6000; use epoll; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; keepalive_timeout 65; #gzip on; include /etc/nginx/conf.d/*.conf; } My php-fpm pool config is the following [www] user = nginx group = nginx listen = /var/run/php5-fpm.sock listen.owner = nginx listen.group = nginx listen.allowed_clients = 127.0.0.1 pm = ondemand pm.max_children = 1500; pm.process_idle_timeout = 5; chdir = / security.limit_extensions = .php I'm using on pm.ondemand since my website has to support many concurrent connections at the same time and i was unable to to it with dynamic/static. I guess this isnt the problem because as i said earlier when i restart nginx+php-fpm at the same time, they are taking too much resources without any request. Here is the screenshot with the CPU Usage http://s28.postimg.org/v54q25zod/Untitled.png

  Read the article

• How to verify power provided to processors is clean

  - by GregC

  Once in a blue moon, I am seeing a blue screen of death on a shiny new Dell R7610 with a single 1100 Watt Dell-provided power supply on a beefy UPS. BCode is 101 (A clock interrupt was not received...), which some say is caused by under-volting a CPU. Naturally, I would have to contact Dell support, and their natural reaction would be to replace a motherboard, a power supply, or CPU, or a mixture of the above components. In synthetic benchmarks, system memory and CPU, as well as graphics memory and CPU perform admirably, staying up for hours and days. My questions are: Is power supply good enough for the application? Does it provide clean enough power to VRMs on the motherboard? Are VRMs good enough for dual Xeon E5-2665? Does C-states logic work correctly? Is there sufficient current provided to PCIe peripherals, such as disk controllers? P.S. Recently, I've gone through the ordeal with HP. They were nice and professional about it, but root cause was not established, and the HP machine still is less than 100%, giving me a blue screen of death once in a couple of months. Here's what quick web-searching turns up: http://www.sevenforums.com/bsod-help-support/35427-win-7-clock-interrupt-bsod-101-error.html#post356791 It appears Dell has addressed the above issue by clocking PCIe bus down to 5GT/sec in A03 BIOS. My disk controllers support PCIe 3.0, meaning that I would have to re-validate stability. Early testing shows improvements. Further testing shows significant decrease in performance on each of the x16 slots with Dell R7610 with A03 BIOS. But now it's running stable. HP machine has received a microcode update in September 2013 SUM (July BIOS) that makes it stable.

  Read the article

• Good HTTP Monitoring tools

  - by ffffff

  I look for HTTP to work with a Linux system server monitor tool every protocol. I know, and will not there be it in whom or a freeware? When, for example, I dump 80/tcp with a packet monitor to be concrete # tethereal -i ppp0 port 80 -x Capturing on ppp0 1244206390.030474 219.111.xx.xx -> 74.125.xx.xx HTTP GET /search?output=js&num=0&dt=1244206414703&client=pub-3031568651010206&q=Cagliari%20Flight&ad=n3&ie=utf8&oe=utf8&channel=0091594208&adtest=off HTTP/1.1 0000 00 04 02 00 00 00 00 00 00 00 00 00 00 00 08 00 ................ 0010 45 00 01 e5 ee 82 40 00 40 06 d2 b5 db 6f 02 5b E.....@[email protected].[ 0020 4a 7d 4f 93 d4 29 00 50 3e df 4c 63 4b 6b 42 e0 J}O..).P>.LcKkB Such output is provided, but there is too much unnecessary information such as an SYN packet or a header. What I want The IP address of the client and sending out character string(Get; the contents of the POST) Among the output character string of the server only as for the HTML (Content-Type:) I am what is chisel) of a thing of text/html. I can set a filter and am the best if only information wanting can accumulate in the log.

  Read the article

• Bypass network stack. Which options do we have? Pros and cons of each option [on hold]

  - by javapowered

  I'm writing trading application. I want to bypass network stack in Linux but I don't know how this can be done. I'm looking for complete list of options with pros and cons of each of them. The only option I know - is to buy solarflare network card which supports OpenOnLoad. What other options should I consider and what is pros and cons of each of them? Well the question is pretty simple - what is the best way to bypass network stack? upd: OpenOnload It achieves performance improvements in part by performing network processing at user-level, bypassing the OS kernel entirely on the data path. Intel DDIO to allow Intel® Ethernet Controllers and adapters to talk directly with the processor cache of the Intel® Xeon® processor E5. What's key difference between these techologies? Do they do roughly the same things? I much better like Intel DDIO because it's much easy to use, but OpenOnload required a lot of installation and tuning. If good OpenOnload application is much faster than good Intel DDIO application?

  Read the article

• MysqlTunner and query_cache_size dilemma

  - by wbad

  On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• Tuning Linux + HAProxy

  - by react

  I'm currently rolling out HAProxy on Centos 6 which will send requests to some Apache HTTPD servers and I'm having issues with performance. I've spent the last couple of days googling and still can't seem to get past 10k/sec connections consistently when benchmarking (sometimes I do get 30k/sec though). I've pinned the IRQ's of the TX/RX queues for both the internal and external NICS to separate CPU cores and made sure HAProxy is pinned to it's own core. I've also made the following adjustments to sysctl.conf: # Max open file descriptors fs.file-max = 331287 # TCP Tuning net.ipv4.tcp_tw_reuse = 1 net.ipv4.ip_local_port_range = 1024 65023 net.ipv4.tcp_max_syn_backlog = 10240 net.ipv4.tcp_max_tw_buckets = 400000 net.ipv4.tcp_max_orphans = 60000 net.ipv4.tcp_synack_retries = 3 net.core.somaxconn = 40000 net.ipv4.tcp_rmem = 4096 8192 16384 net.ipv4.tcp_wmem = 4096 8192 16384 net.ipv4.tcp_mem = 65536 98304 131072 net.core.netdev_max_backlog = 40000 net.ipv4.tcp_tw_reuse = 1 If I use AB to hit the a webserver directly I easily get 30k/s connections. If I stop the webservers and use AB to hit HAProxy then I get 30k/s connections but obviously it's useless. I've also disabled iptables for now since I read that nf_conntrack can slow everything down, no change. I've also disabled the irqbalance service. The fact that I can hit each individual device with 30k/s makes me believe the tuning of the servers is OK and that it must be some HAProxy config? Here's the config which I've built from reading tuning articles, etc http://pastebin.com/zsCyAtgU The server is a dual Xeon CPU E5-2620 (6 cores) with 32GB of RAM. Running Centos 6.2 x64. The private and public interfaces are on separate NICS. Anyone have any ideas? Thanks.

  Read the article

• Strange Domain name under the same IP Address

  - by Mike Chip

  There's something really weird happening in my server. But first things first: I wanted to have my website and chose the domain name "myowndomain.com", Now on my domain registrar I point "myowndomain.com" to the address of my recently setup VPS, let's say 50.50.50.50 So I installed everything I needed to run my website, and I started to notice strange queries coming from different IP Addresses. Like these [client 123.123.123.123] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php [client 456.456.456.456] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php or like this (Really a long line, I cut some things) GET /?s=vod-show-id-22-area-%E5%85%B6%E4%BB%96-language-%E9%9F%A9%E8%AF%AD.html HTTP/1.1" 301 295 "http://v.strangedomain.com/?s=vod-s ...[cut]... spider" That above is happening the most. The 'strangedomain.com' returns the same IP address of my VPS which my website is hosted on. The whois of such domain shows it's registered to a chinese. But the street name didn't look so right (like a huge single word), so I think all of that info might be fake, but still might be a chinese. I also noticed that all 'clients' trying to access the 'strangedomain.com' is coming from china. If I type in the browser 'strangedomain.com', I see my website. I'm worried, because my website is actually an e-commerce. I don't know if 'strangedomain.com' WAS a website on 50.50.50.50 in the not so far past, or if it's something else.

  Read the article

• Server periodically freezing - Help Stabilizing

  - by JonDog

  We run an asp.net/sql server data collection website with a hand full of clients dumping data in and running reports. We moved to a new server (specs below) and have had issues with it freezing and having to reboot it a dozen times over the pass six months. The hosting company has mentioned possible causes (listed below) but cant give a definite answer on what is going wrong. They have offered to reconfigure how ever I like. We have benefited from having a much faster system and really dont want to get rid of the ssd's unless they are the issue. Two possible setup changes that I've talked with them about are also listed below. Any suggestions on what maybe causing the freezing issue as well as suggestion on a new setup would be great. My main questions are: Do SSD generally have problems running the OS & SQL Server on the same RAID Array? and Are the new SSD's still unrefined enough to be running in a production environment? Thanks Current: Xeon Quad Core E3-1270 3.40 Ghz 16 GB DDR3-1333 ECC SDRAM First Hard Drive: 120GB Intel SSD Second Hard Drive: 120GB Intel SSD Third Hard Drive: 120GB Intel SSD Fourth Hard Drive: 120GB Intel SSD SAS 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit MSSQL 2008 Web Edition Possible Causes: Running Sql Server & OS on same RAID Array OS Software Issues Using SSD's CPU Underpowered Not enough RAM Option 1 2x Xeon Quad Core E5-2603 1.80 GHz 16 GB DDR3-1333 ECC SDRAM 1 x 240GB Intel SSD - OS 3 x 1 TB SATA HDD (7200 RPM) - SQL Server SATA 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit Option 2 Dell PowerEdge E3-1270v2 3.5GHz 4 Cores 16 GB DDR3-1600 UDIMM 4 x 128 GB Samsung 840 Pro SSD Add-in H200 (SAS/SATA Controller), 4 Hard Drives - RAID 10 Windows 2012 Standard Edition - 64 Bit

  Read the article

• Nginx and client certificates from hierarchical OpenSSL-based certification authorities

  - by Fmy Oen

  I'm trying to set up root certification authority, subordinate certification authority and to generate the client certificates signed by any of this CA that nginx 0.7.67 on Debian Squeeze will accept. My problem is that root CA signed client certificate works fine while subordinate CA signed one results in "400 Bad Request. The SSL certificate error". Step 1: nginx virtual host configuration: server { server_name test.local; access_log /var/log/nginx/test.access.log; listen 443 default ssl; keepalive_timeout 70; ssl_protocols SSLv3 TLSv1; ssl_ciphers AES128-SHA:AES256-SHA:RC4-SHA:DES-CBC3-SHA:RC4-MD5; ssl_certificate /etc/nginx/ssl/server.crt; ssl_certificate_key /etc/nginx/ssl/server.key; ssl_client_certificate /etc/nginx/ssl/client.pem; ssl_verify_client on; ssl_session_cache shared:SSL:10m; ssl_session_timeout 5m; location / { proxy_pass http://testsite.local/; } } Step 2: PKI infrastructure organization for both root and subordinate CA (based on this article): # mkdir ~/pki && cd ~/pki # mkdir rootCA subCA # cp -v /etc/ssl/openssl.cnf rootCA/ # cd rootCA/ # mkdir certs private crl newcerts; touch serial; echo 01 > serial; touch index.txt; touch crlnumber; echo 01 > crlnumber # cp -Rvp * ../subCA/ Almost no changes was made to rootCA/openssl.cnf: [ CA_default ] dir = . # Where everything is kept ... certificate = $dir/certs/rootca.crt # The CA certificate ... private_key = $dir/private/rootca.key # The private key and to subCA/openssl.cnf: [ CA_default ] dir = . # Where everything is kept ... certificate = $dir/certs/subca.crt # The CA certificate ... private_key = $dir/private/subca.key # The private key Step 3: Self-signed root CA certificate generation: # openssl genrsa -out ./private/rootca.key -des3 2048 # openssl req -x509 -new -key ./private/rootca.key -out certs/rootca.crt -config openssl.cnf Enter pass phrase for ./private/rootca.key: You are about to be asked to enter information that will be incorporated into your certificate request. What you are about to enter is what is called a Distinguished Name or a DN. There are quite a few fields but you can leave some blank For some fields there will be a default value, If you enter '.', the field will be left blank. ----- Country Name (2 letter code) [AU]: State or Province Name (full name) [Some-State]: Locality Name (eg, city) []: Organization Name (eg, company) [Internet Widgits Pty Ltd]: Organizational Unit Name (eg, section) []: Common Name (eg, YOUR name) []:rootca Email Address []: Step 4: Subordinate CA certificate generation: # cd ../subCA # openssl genrsa -out ./private/subca.key -des3 2048 # openssl req -new -key ./private/subca.key -out subca.csr -config openssl.cnf Enter pass phrase for ./private/subca.key: You are about to be asked to enter information that will be incorporated into your certificate request. What you are about to enter is what is called a Distinguished Name or a DN. There are quite a few fields but you can leave some blank For some fields there will be a default value, If you enter '.', the field will be left blank. ----- Country Name (2 letter code) [AU]: State or Province Name (full name) [Some-State]: Locality Name (eg, city) []: Organization Name (eg, company) [Internet Widgits Pty Ltd]: Organizational Unit Name (eg, section) []: Common Name (eg, YOUR name) []:subca Email Address []: Please enter the following 'extra' attributes to be sent with your certificate request A challenge password []: An optional company name []: Step 5: Subordinate CA certificate signing by root CA certificate: # cd ../rootCA/ # openssl ca -in ../subCA/subca.csr -extensions v3_ca -config openssl.cnf Using configuration from openssl.cnf Enter pass phrase for ./private/rootca.key: Check that the request matches the signature Signature ok Certificate Details: Serial Number: 1 (0x1) Validity Not Before: Feb 4 10:49:43 2013 GMT Not After : Feb 4 10:49:43 2014 GMT Subject: countryName = AU stateOrProvinceName = Some-State organizationName = Internet Widgits Pty Ltd commonName = subca X509v3 extensions: X509v3 Subject Key Identifier: C9:E2:AC:31:53:81:86:3F:CD:F8:3D:47:10:FC:E5:8E:C2:DA:A9:20 X509v3 Authority Key Identifier: keyid:E9:50:E6:BF:57:03:EA:6E:8F:21:23:86:BB:44:3D:9F:8F:4A:8B:F2 DirName:/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca serial:9F:FB:56:66:8D:D3:8F:11 X509v3 Basic Constraints: CA:TRUE Certificate is to be certified until Feb 4 10:49:43 2014 GMT (365 days) Sign the certificate? [y/n]:y 1 out of 1 certificate requests certified, commit? [y/n]y ... # cd ../subCA/ # cp -v ../rootCA/newcerts/01.pem certs/subca.crt Step 6: Server certificate generation and signing by root CA (for nginx virtual host): # cd ../rootCA # openssl genrsa -out ./private/server.key -des3 2048 # openssl req -new -key ./private/server.key -out server.csr -config openssl.cnf Enter pass phrase for ./private/server.key: You are about to be asked to enter information that will be incorporated into your certificate request. What you are about to enter is what is called a Distinguished Name or a DN. There are quite a few fields but you can leave some blank For some fields there will be a default value, If you enter '.', the field will be left blank. ----- Country Name (2 letter code) [AU]: State or Province Name (full name) [Some-State]: Locality Name (eg, city) []: Organization Name (eg, company) [Internet Widgits Pty Ltd]: Organizational Unit Name (eg, section) []: Common Name (eg, YOUR name) []:test.local Email Address []: Please enter the following 'extra' attributes to be sent with your certificate request A challenge password []: An optional company name []: # openssl ca -in server.csr -out certs/server.crt -config openssl.cnf Step 7: Client #1 certificate generation and signing by root CA: # openssl genrsa -out ./private/client1.key -des3 2048 # openssl req -new -key ./private/client1.key -out client1.csr -config openssl.cnf Enter pass phrase for ./private/client1.key: You are about to be asked to enter information that will be incorporated into your certificate request. What you are about to enter is what is called a Distinguished Name or a DN. There are quite a few fields but you can leave some blank For some fields there will be a default value, If you enter '.', the field will be left blank. ----- Country Name (2 letter code) [AU]: State or Province Name (full name) [Some-State]: Locality Name (eg, city) []: Organization Name (eg, company) [Internet Widgits Pty Ltd]: Organizational Unit Name (eg, section) []: Common Name (eg, YOUR name) []:Client #1 Email Address []: Please enter the following 'extra' attributes to be sent with your certificate request A challenge password []: An optional company name []: # openssl ca -in client1.csr -out certs/client1.crt -config openssl.cnf Step 8: Client #1 certificate converting to PKCS12 format: # openssl pkcs12 -export -out certs/client1.p12 -inkey private/client1.key -in certs/client1.crt -certfile certs/rootca.crt Step 9: Client #2 certificate generation and signing by subordinate CA: # cd ../subCA/ # openssl genrsa -out ./private/client2.key -des3 2048 # openssl req -new -key ./private/client2.key -out client2.csr -config openssl.cnf Enter pass phrase for ./private/client2.key: You are about to be asked to enter information that will be incorporated into your certificate request. What you are about to enter is what is called a Distinguished Name or a DN. There are quite a few fields but you can leave some blank For some fields there will be a default value, If you enter '.', the field will be left blank. ----- Country Name (2 letter code) [AU]: State or Province Name (full name) [Some-State]: Locality Name (eg, city) []: Organization Name (eg, company) [Internet Widgits Pty Ltd]: Organizational Unit Name (eg, section) []: Common Name (eg, YOUR name) []:Client #2 Email Address []: Please enter the following 'extra' attributes to be sent with your certificate request A challenge password []: An optional company name []: # openssl ca -in client2.csr -out certs/client2.crt -config openssl.cnf Step 10: Client #2 certificate converting to PKCS12 format: # openssl pkcs12 -export -out certs/client2.p12 -inkey private/client2.key -in certs/client2.crt -certfile certs/subca.crt Step 11: Passing server certificate and private key to nginx (performed with OS superuser privileges): # cd ../rootCA/ # cp -v certs/server.crt /etc/nginx/ssl/ # cp -v private/server.key /etc/nginx/ssl/ Step 12: Passing root and subordinate CA certificates to nginx (performed with OS superuser privileges): # cat certs/rootca.crt > /etc/nginx/ssl/client.pem # cat ../subCA/certs/subca.crt >> /etc/nginx/ssl/client.pem client.pem file look like this: # cat /etc/nginx/ssl/client.pem -----BEGIN CERTIFICATE----- MIID6TCCAtGgAwIBAgIJAJ/7VmaN048RMA0GCSqGSIb3DQEBBQUAMFYxCzAJBgNV BAYTAkFVMRMwEQYDVQQIEwpTb21lLVN0YXRlMSEwHwYDVQQKExhJbnRlcm5ldCBX aWRnaXRzIFB0eSBMdGQxDzANBgNVBAMTBnJvb3RjYTAeFw0xMzAyMDQxMDM1NTda ... -----END CERTIFICATE----- Certificate: Data: Version: 3 (0x2) Serial Number: 1 (0x1) ... -----BEGIN CERTIFICATE----- MIID4DCCAsigAwIBAgIBATANBgkqhkiG9w0BAQUFADBWMQswCQYDVQQGEwJBVTET MBEGA1UECBMKU29tZS1TdGF0ZTEhMB8GA1UEChMYSW50ZXJuZXQgV2lkZ2l0cyBQ dHkgTHRkMQ8wDQYDVQQDEwZyb290Y2EwHhcNMTMwMjA0MTA0OTQzWhcNMTQwMjA0 ... -----END CERTIFICATE----- It looks like everything is working fine: # service nginx reload # Reloading nginx configuration: Enter PEM pass phrase: # nginx. # Step 13: Installing *.p12 certificates in browser (Firefox in my case) gives the problem I've mentioned above. Client #1 = 200 OK, Client #2 = 400 Bad request/The SSL certificate error. Any ideas what should I do? Update 1: Results of SSL connection test attempts: # openssl s_client -connect test.local:443 -CAfile ~/pki/rootCA/certs/rootca.crt -cert ~/pki/rootCA/certs/client1.crt -key ~/pki/rootCA/private/client1.key -showcerts Enter pass phrase for tmp/testcert/client1.key: CONNECTED(00000003) depth=1 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = rootca verify return:1 depth=0 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = test.local verify return:1 --- Certificate chain 0 s:/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=test.local i:/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca -----BEGIN CERTIFICATE----- MIIDpjCCAo6gAwIBAgIBAjANBgkqhkiG9w0BAQUFADBWMQswCQYDVQQGEwJBVTET MBEGA1UECBMKU29tZS1TdGF0ZTEhMB8GA1UEChMYSW50ZXJuZXQgV2lkZ2l0cyBQ dHkgTHRkMQ8wDQYDVQQDEwZyb290Y2EwHhcNMTMwMjA0MTEwNjAzWhcNMTQwMjA0 ... -----END CERTIFICATE----- 1 s:/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca i:/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca -----BEGIN CERTIFICATE----- MIID6TCCAtGgAwIBAgIJAJ/7VmaN048RMA0GCSqGSIb3DQEBBQUAMFYxCzAJBgNV BAYTAkFVMRMwEQYDVQQIEwpTb21lLVN0YXRlMSEwHwYDVQQKExhJbnRlcm5ldCBX aWRnaXRzIFB0eSBMdGQxDzANBgNVBAMTBnJvb3RjYTAeFw0xMzAyMDQxMDM1NTda ... -----END CERTIFICATE----- --- Server certificate subject=/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=test.local issuer=/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca --- Acceptable client certificate CA names /C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca /C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=subca --- SSL handshake has read 3395 bytes and written 2779 bytes --- New, TLSv1/SSLv3, Cipher is AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: zlib compression Expansion: zlib compression SSL-Session: Protocol : TLSv1 Cipher : AES256-SHA Session-ID: 15BFC2029691262542FAE95A48078305E76EEE7D586400F8C4F7C516B0F9D967 Session-ID-ctx: Master-Key: 23246CF166E8F3900793F0A2561879E5DB07291F32E99591BA1CF53E6229491FEAE6858BFC9AACAF271D9C3706F139C7 Key-Arg : None PSK identity: None PSK identity hint: None SRP username: None TLS session ticket: 0000 - c2 5e 1d d2 b5 6d 40 23-b2 40 89 e4 35 75 70 07 .^...m@#[email protected]. 0010 - 1b bb 2b e6 e0 b5 ab 10-10 bf 46 6e aa 67 7f 58 ..+.......Fn.g.X 0020 - cf 0e 65 a4 67 5a 15 ba-aa 93 4e dd 3d 6e 73 4c ..e.gZ....N.=nsL 0030 - c5 56 f6 06 24 0f 48 e6-38 36 de f1 b5 31 c5 86 .V..$.H.86...1.. ... 0440 - 4c 53 39 e3 92 84 d2 d0-e5 e2 f5 8a 6a a8 86 b1 LS9.........j... Compression: 1 (zlib compression) Start Time: 1359989684 Timeout : 300 (sec) Verify return code: 0 (ok) --- Everything seems fine with Client #2 and root CA certificate but request returns 400 Bad Request error: # openssl s_client -connect test.local:443 -CAfile ~/pki/rootCA/certs/rootca.crt -cert ~/pki/subCA/certs/client2.crt -key ~/pki/subCA/private/client2.key -showcerts Enter pass phrase for tmp/testcert/client2.key: CONNECTED(00000003) depth=1 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = rootca verify return:1 depth=0 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = test.local verify return:1 ... Compression: 1 (zlib compression) Start Time: 1359989989 Timeout : 300 (sec) Verify return code: 0 (ok) --- GET / HTTP/1.0 HTTP/1.1 400 Bad Request Server: nginx/0.7.67 Date: Mon, 04 Feb 2013 15:00:43 GMT Content-Type: text/html Content-Length: 231 Connection: close <html> <head><title>400 The SSL certificate error</title></head> <body bgcolor="white"> <center><h1>400 Bad Request</h1></center> <center>The SSL certificate error</center> <hr><center>nginx/0.7.67</center> </body> </html> closed Verification fails with Client #2 certificate and subordinate CA certificate: # openssl s_client -connect test.local:443 -CAfile ~/pki/subCA/certs/subca.crt -cert ~/pki/subCA/certs/client2.crt -key ~/pki/subCA/private/client2.key -showcerts Enter pass phrase for tmp/testcert/client2.key: CONNECTED(00000003) depth=1 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = rootca verify error:num=19:self signed certificate in certificate chain verify return:0 ... Compression: 1 (zlib compression) Start Time: 1359990354 Timeout : 300 (sec) Verify return code: 19 (self signed certificate in certificate chain) --- GET / HTTP/1.0 HTTP/1.1 400 Bad Request ... Still getting 400 Bad Request error with concatenated CA certificates and Client #2 (but still everything ok with Client #1): # cat certs/rootca.crt ../subCA/certs/subca.crt > certs/concatenatedca.crt # openssl s_client -connect test.local:443 -CAfile ~/pki/rootCA/certs/concatenatedca.crt -cert ~/pki/subCA/certs/client2.crt -key ~/pki/subCA/private/client2.key -showcerts Enter pass phrase for tmp/testcert/client2.key: CONNECTED(00000003) depth=1 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = rootca verify return:1 depth=0 C = AU, ST = Some-State, O = Internet Widgits Pty Ltd, CN = test.local verify return:1 --- ... Compression: 1 (zlib compression) Start Time: 1359990772 Timeout : 300 (sec) Verify return code: 0 (ok) --- GET / HTTP/1.0 HTTP/1.1 400 Bad Request ... Update 2: I've managed to recompile nginx with enabled debug. Here is the part of successfull conection by Client #1 track: 2013/02/05 14:08:23 [debug] 38701#0: *119 accept: <MY IP ADDRESS> fd:3 2013/02/05 14:08:23 [debug] 38701#0: *119 event timer add: 3: 60000:2856497512 2013/02/05 14:08:23 [debug] 38701#0: *119 kevent set event: 3: ft:-1 fl:0025 2013/02/05 14:08:23 [debug] 38701#0: *119 malloc: 28805200:660 2013/02/05 14:08:23 [debug] 38701#0: *119 malloc: 28834400:1024 2013/02/05 14:08:23 [debug] 38701#0: *119 posix_memalign: 28860000:4096 @16 2013/02/05 14:08:23 [debug] 38701#0: *119 http check ssl handshake 2013/02/05 14:08:23 [debug] 38701#0: *119 https ssl handshake: 0x16 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL server name: "test.local" 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_do_handshake: -1 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_get_error: 2 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL handshake handler: 0 2013/02/05 14:08:23 [debug] 38701#0: *119 verify:1, error:0, depth:1, subject:"/C=AU /ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca",issuer: "/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca" 2013/02/05 14:08:23 [debug] 38701#0: *119 verify:1, error:0, depth:0, subject:"/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=Client #1",issuer: "/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca" 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_do_handshake: 1 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL: TLSv1, cipher: "AES256-SHA SSLv3 Kx=RSA Au=RSA Enc=AES(256) Mac=SHA1" 2013/02/05 14:08:23 [debug] 38701#0: *119 http process request line 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_read: -1 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_get_error: 2 2013/02/05 14:08:23 [debug] 38701#0: *119 http process request line 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_read: 1 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_read: 524 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_read: -1 2013/02/05 14:08:23 [debug] 38701#0: *119 SSL_get_error: 2 2013/02/05 14:08:23 [debug] 38701#0: *119 http request line: "GET / HTTP/1.1" And here is the part of unsuccessfull conection by Client #2 track: 2013/02/05 13:51:34 [debug] 38701#0: *112 accept: <MY_IP_ADDRESS> fd:3 2013/02/05 13:51:34 [debug] 38701#0: *112 event timer add: 3: 60000:2855488975 2013/02/05 13:51:34 [debug] 38701#0: *112 kevent set event: 3: ft:-1 fl:0025 2013/02/05 13:51:34 [debug] 38701#0: *112 malloc: 28805200:660 2013/02/05 13:51:34 [debug] 38701#0: *112 malloc: 28834400:1024 2013/02/05 13:51:34 [debug] 38701#0: *112 posix_memalign: 28860000:4096 @16 2013/02/05 13:51:34 [debug] 38701#0: *112 http check ssl handshake 2013/02/05 13:51:34 [debug] 38701#0: *112 https ssl handshake: 0x16 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL server name: "test.local" 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_do_handshake: -1 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_get_error: 2 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL handshake handler: 0 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_do_handshake: -1 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_get_error: 2 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL handshake handler: 0 2013/02/05 13:51:34 [debug] 38701#0: *112 verify:0, error:20, depth:1, subject:"/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=subca",issuer: "/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca" 2013/02/05 13:51:34 [debug] 38701#0: *112 verify:0, error:27, depth:1, subject:"/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=subca",issuer: "/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=rootca" 2013/02/05 13:51:34 [debug] 38701#0: *112 verify:1, error:27, depth:0, subject:"/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=Client #2",issuer: "/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd/CN=subca" 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_do_handshake: 1 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL: TLSv1, cipher: "AES256-SHA SSLv3 Kx=RSA Au=RSA Enc=AES(256) Mac=SHA1" 2013/02/05 13:51:34 [debug] 38701#0: *112 http process request line 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_read: 1 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_read: 524 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_read: -1 2013/02/05 13:51:34 [debug] 38701#0: *112 SSL_get_error: 2 2013/02/05 13:51:34 [debug] 38701#0: *112 http request line: "GET / HTTP/1.1" So I'm getting OpenSSL error #20 and then #27. According to verify documentation: 20 X509_V_ERR_UNABLE_TO_GET_ISSUER_CERT_LOCALLY: unable to get local issuer certificate the issuer certificate could not be found: this occurs if the issuer certificate of an untrusted certificate cannot be found. 27 X509_V_ERR_CERT_UNTRUSTED: certificate not trusted the root CA is not marked as trusted for the specified purpose.

  Read the article

• Oracle Announces Oracle Exadata X3 Database In-Memory Machine

  - by jgelhaus

  Fourth Generation Exadata X3 Systems are Ideal for High-End OLTP, Large Data Warehouses, and Database Clouds; Eighth-Rack Configuration Offers New Low-Cost Entry Point ORACLE OPENWORLD, SAN FRANCISCO – October 1, 2012 News Facts During his opening keynote address at Oracle OpenWorld, Oracle CEO, Larry Ellison announced the Oracle Exadata X3 Database In-Memory Machine - the latest generation of its Oracle Exadata Database Machines. The Oracle Exadata X3 Database In-Memory Machine is a key component of the Oracle Cloud. Oracle Exadata X3-2 Database In-Memory Machine and Oracle Exadata X3-8 Database In-Memory Machine can store up to hundreds of Terabytes of compressed user data in Flash and RAM memory, virtually eliminating the performance overhead of reads and writes to slow disk drives, making Exadata X3 systems the ideal database platforms for the varied and unpredictable workloads of cloud computing. In order to realize the highest performance at the lowest cost, the Oracle Exadata X3 Database In-Memory Machine implements a mass memory hierarchy that automatically moves all active data into Flash and RAM memory, while keeping less active data on low-cost disks. With a new Eighth-Rack configuration, the Oracle Exadata X3-2 Database In-Memory Machine delivers a cost-effective entry point for smaller workloads, testing, development and disaster recovery systems, and is a fully redundant system that can be used with mission critical applications. Next-Generation Technologies Deliver Dramatic Performance Improvements Oracle Exadata X3 Database In-Memory Machines use a combination of scale-out servers and storage, InfiniBand networking, smart storage, PCI Flash, smart memory caching, and Hybrid Columnar Compression to deliver extreme performance and availability for all Oracle Database Workloads. Oracle Exadata X3 Database In-Memory Machine systems leverage next-generation technologies to deliver significant performance enhancements, including: Four times the Flash memory capacity of the previous generation; with up to 40 percent faster response times and 100 GB/second data scan rates. Combined with Exadata’s unique Hybrid Columnar Compression capabilities, hundreds of Terabytes of user data can now be managed entirely within Flash; 20 times more capacity for database writes through updated Exadata Smart Flash Cache software. The new Exadata Smart Flash Cache software also runs on previous generation Exadata systems, increasing their capacity for writes tenfold; 33 percent more database CPU cores in the Oracle Exadata X3-2 Database In-Memory Machine, using the latest 8-core Intel® Xeon E5-2600 series of processors; Expanded 10Gb Ethernet connectivity to the data center in the Oracle Exadata X3-2 provides 40 10Gb network ports per rack for connecting users and moving data; Up to 30 percent reduction in power and cooling. Configured for Your Business, Available Today Oracle Exadata X3-2 Database In-Memory Machine systems are available in a Full-Rack, Half-Rack, Quarter-Rack, and the new low-cost Eighth-Rack configuration to satisfy the widest range of applications. Oracle Exadata X3-8 Database In-Memory Machine systems are available in a Full-Rack configuration, and both X3 systems enable multi-rack configurations for virtually unlimited scalability. Oracle Exadata X3-2 and X3-8 Database In-Memory Machines are fully compatible with prior Exadata generations and existing systems can also be upgraded with Oracle Exadata X3-2 servers. Oracle Exadata X3 Database In-Memory Machine systems can be used immediately with any application certified with Oracle Database 11g R2 and Oracle Real Application Clusters, including SAP, Oracle Fusion Applications, Oracle’s PeopleSoft, Oracle’s Siebel CRM, the Oracle E-Business Suite, and thousands of other applications. Supporting Quotes “Forward-looking enterprises are moving towards Cloud Computing architectures,” said Andrew Mendelsohn, senior vice president, Oracle Database Server Technologies. “Oracle Exadata’s unique ability to run any database application on a fully scale-out architecture using a combination of massive memory for extreme performance and low-cost disk for high capacity delivers the ideal solution for Cloud-based database deployments today.” Supporting Resources Oracle Press Release Oracle Exadata Database Machine Oracle Exadata X3-2 Database In-Memory Machine Oracle Exadata X3-8 Database In-Memory Machine Oracle Database 11g Follow Oracle Database via Blog, Facebook and Twitter Oracle OpenWorld 2012 Oracle OpenWorld 2012 Keynotes Like Oracle OpenWorld on Facebook Follow Oracle OpenWorld on Twitter Oracle OpenWorld Blog Oracle OpenWorld on LinkedIn Mark Hurd's keynote with Andy Mendelsohn and Juan Loaiza - - watch for the replay to be available soon at http://www.youtube.com/user/Oracle or http://www.oracle.com/openworld/live/on-demand/index.html

  Read the article

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• Intermittent internet connectivity

  - by Rob Oplawar

  UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

  Read the article

• Google Translate API for iPhone - UTF8 problem in Chinese Translation

  - by Sky Chen

  I've tested a workable translation API url by: http://translate.google.com/translate_a/t?client=t&text=%E5%BB%A3%E5%A0%B4&langpair=zh|zh-CN And it returns the correct result as the following which is in JSON format: {"sentences":[{"trans":"??","orig":"??","translit":"Guangchang"}],"src":"zh-CN"} However, when I try to use this function in XCode, I experienced this problem ... Here is my code: NSData *data; NSString *urlPath = [NSString stringWithFormat:@"/translate_a/t?client=t&text=%@&langpair=zh|zh-CN",qText]; NSURL *url = [[NSURL alloc] initWithScheme:@"http" host:@"translate.google.com" path:urlPath]; NSMutableURLRequest *request = [[[NSMutableURLRequest alloc] init] autorelease]; [request setURL:url]; [request setHTTPMethod:@"GET"]; NSURLResponse *response; NSError *error; data = [NSURLConnection sendSynchronousRequest:request returningResponse:&response error:&error]; NSString *result = [[NSString alloc] initWithData:data encoding:NSUTF8StringEncoding]; //Problem's here. It returns nil. NSLog(result); Initially I guessed it's encoding problem so I tried other encoding as well (NSISOLatin1StringEncoding) , but I got wrong answer: {"sentences":[{"trans":"ã ","orig":"ã ","translit":"Tu¨¯ "}],"src":"zh-CN"} Does anyone know how to solve this problem? Thank you very much!

  Read the article

• Why execution of a portion of code loaded from external file is not halted by the OS?

  - by menjaraz

  I've harnessed a project released on internet a long time ago. Here comes the details, all irrelevant things being stripped off for sake of concision and clarity. A binary file whose content is descibed below HEX DUMP: 55 89 E5 83 EC 08 C7 45 FC 00 00 00 00 8B 45 FC 3B 45 10 72 02 EB 19 8B 45 FC 8B 55 0C 01 C2 8B 45 FC 03 45 08 8A 00 88 02 8D 45 FC FF 00 EB DD C6 45 FA 00 83 7D 10 01 76 6C 80 7D FA 00 74 02 EB 64 C6 45 FA 01 C7 45 FC 00 00 00 00 8B 45 10 48 39 45 FC 72 02 EB E2 8B 45 FC 8B 4D 0C 01 C1 8B 45 FC 03 45 0C 8D 50 01 8A 01 3A 02 73 30 8B 45 FC 03 45 0C 8A 00 88 45 FB 8B 45 FC 8B 55 0C 01 C2 8B 45 FC 03 45 0C 40 8A 00 88 02 8B 45 FC 03 45 0C 8D 50 01 8A 45 FB 88 02 C6 45 FA 00 8D 45 FC FF 00 EB A7 C9 C2 0C 00 90 90 90 90 90 90 is loaded into memory and executed using the following method snippet var MySrcArray, MyDestArray: array [1 .. 15] of Byte; // ... MyBuffer: Pointer; TheProc: procedure; SortIt: procedure(ASrc, ADest: Pointer; ASize: LongWord); stdcall; begin // Initialization of MySrcArray with random Bytes and display here ... // Instructions of loading of the binary file into MyBuffer using merely **GetMem** here ... @SortIt := MyBuffer; try SortIt(@MySrcArray, @MyDestArray, 15); // Display of MyDestArray (The outcome of the processing !) except // Invalid code error handling end; // Cleaning code here ... end; works like a charm on my box. My Question: How comes it works without using VirtualAlloc and/or VirtualProtect?

  Read the article

• CSV Parser works in windows, not linux.

  - by ladookie

  I'm parsing a CSV file that looks like this: E1,E2,E7,E8,,, E2,E1,E3,,,, E3,E2,E8,,, E4,E5,E8,E11,,, I store the first entry in each line in a string, and the rest go in a vector of strings: while (getline(file_input, line)) { stringstream tokenizer; tokenizer << line; getline(tokenizer, roomID, ','); vector<string> aVector; while (getline(tokenizer, adjRoomID, ',')) { if (!adjRoomID.empty()) { aVector.push_back(adjRoomID); } } Room aRoom(roomID, aVector); rooms.addToTail(aRoom); } In windows this works fine, however in Linux the first entry of each vector mysteriously loses the first character. For Example in the first iteration through the while loop: roomID would be E1 and aVector would be 2 E7 E8 then the second iteration: roomID would be E2 and aVector would be 1 E3 Notice the missing E's in the first entry of aVector. when I put in some debugging code it appears that it is initially being stored correctly in the vector, but then something overwrites it. Kudos to whoever figures this one out. Seems bizarre to me. rooms is declared as such: DLList<Room> rooms where DLList stands for Doubly-Linked list.

  Read the article

• Network Bridging for WiFi-to-Ethernet in linux

  - by shakaran

  It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

  Read the article

• How to make Linux reliably boot on multi-cpu machines?

  - by Adam Tabi

  I've got two machines, one with 4x12 AMD Opteron cores (AMD Opteron(tm) Processor 6176), one with 2x8 Xeon cores (HT disabled; Intel(R) Xeon(R) CPU E5-2660 0 @ 2.20GHz). On both machines I experience difficulties during boot of Linux using recent kernels. The system hangs during the initialization of the kernel, before or just when initramfs started initializing the hardware. The last thing which got displayed was a stacktrace like this: CPU: 31 PID: 0 Comm: swapper/31 Tainted: G D 3.11.6-hardened #11 Hardware name: Supermicro X9DRT-HF+/X9DRT-HF+, BIOS 3.00 07/08/2013 task: ffff880854695500 ti: ffff880854695a28 task.ti: ffff880854695a28 RIP: 0010:[<ffffffff8100a82e>] [<ffffffff8100a82e>] default_idle+0x6/0xe RSP: 0000:ffff8808546b3ec8 EFLAGS: 00000286 RAX: ffffffff8100a828 RBX: ffff880854695a28 RCX: 00000000ffffffff RDX: 0100000000000000 RSI: 0000000000000000 RDI: ffff88107fdec690 RBP: ffff8808546b3ec8 R08: 0000000000000000 R09: ffff880854695500 R10: ffff880854695500 R11: 0000000000000001 R12: ffff880854695a28 R13: ffff880854695a28 R14: ffff880854695a28 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88107fde0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000002b43256a960 CR3: 00000000016b5000 CR4: 00000000000607f0 Stack: ffff8808546b3ed8 ffffffff8100aec9 ffff8808546b3f10 ffffffff8109ce25 334ab55852ec7aef 000000000000001f ffffffff8102d6c0 0000000000000000 0000000000000000 ffff8808546b3f48 ffffffff810276e0 ffff8808546b3f28 Call Trace: [<ffffffff8100aec9>] arch_cpu_idle+0x20/0x2b [<ffffffff8109ce25>] cpu_startup_entry+0xed/0x138 [<ffffffff8102d6c0>] ? flat_init_apic_ldr+0x80/0x80 [<ffffffff810276e0>] start_secondary+0x2c9/0x2f8 I compiled the kernel myself and it works fine, if I boot with nolapic. Yet, only one core is used. Also, the kernel of RHEL6 seems to work fine. I suspect that there are some patches used to make things work. Using the kernel config file from RHEL6 and building a more recent kernel yields the same problems. On the Xeon machine, things got better by disabling Hyperthreading completely. The machine now boots successfully on at least 4 out of 5 times. And if it boots, multicore stuff works just fine. However, I'm wondering about what to do about the AMD machine. So to sum it up: Gentoo kernel 3.6 - 3.11 won't reliably boot those machines unless you reduce the amount of cores (e.g. via nolapic). RHEL6 kernel (which is 2.6.32) boots just fine. RH kernel config used to build a 3.x kernel won't yield a working kernel. Not distribution specific (apart from the kernel being used). These stack traces got printed every minute or so. The kernel seems to be stuck in an endless loop. Yet, a recent kernel is needed for various reasons. So the question is: What does the RHEL6 kernel do, what vanilla or gentoo kernels don't do? Is there a boot option that might lead to a reliable boot with all the cores enabled? Best, Adam

  Read the article

• ffmpeg not using all cores

  - by user2783132

  I just got my new server with two intel e5-2695 but I was shocked to see that ffmpeg or ubuntu doesn't utilize all cores. top while ffmpeg was running top - 23:35:25 up 2:41, 2 users, load average: 5.35, 4.37, 3.12 Tasks: 333 total, 2 running, 331 sleeping, 0 stopped, 0 zombie %Cpu0 : 0.0 us, 1.0 sy, 35.6 ni, 63.4 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu1 : 0.0 us, 0.7 sy, 35.5 ni, 63.9 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu2 : 0.0 us, 0.7 sy, 33.4 ni, 65.9 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu3 : 0.0 us, 0.0 sy, 32.7 ni, 67.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu4 : 0.0 us, 0.3 sy, 32.3 ni, 67.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu5 : 0.0 us, 0.3 sy, 33.0 ni, 66.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu6 : 0.0 us, 0.0 sy, 32.6 ni, 67.4 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu7 : 0.0 us, 0.3 sy, 32.7 ni, 67.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu8 : 0.0 us, 0.7 sy, 32.6 ni, 66.8 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu9 : 0.0 us, 0.3 sy, 33.9 ni, 65.8 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu10 : 0.0 us, 0.0 sy, 35.0 ni, 65.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu11 : 0.0 us, 0.7 sy, 30.0 ni, 69.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu12 : 21.1 us, 0.0 sy, 0.0 ni, 78.9 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu13 : 0.7 us, 0.0 sy, 4.3 ni, 95.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu14 : 0.3 us, 0.0 sy, 5.0 ni, 94.6 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu15 : 24.9 us, 0.0 sy, 0.0 ni, 75.1 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu16 : 0.3 us, 0.0 sy, 3.7 ni, 96.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu17 : 0.7 us, 0.3 sy, 4.9 ni, 94.1 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu18 : 1.0 us, 0.0 sy, 4.6 ni, 94.4 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu19 : 0.7 us, 0.0 sy, 4.7 ni, 94.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu20 : 11.1 us, 0.0 sy, 0.0 ni, 88.9 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu21 : 1.3 us, 0.0 sy, 4.6 ni, 94.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu22 : 2.0 us, 0.3 sy, 4.3 ni, 93.4 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu23 : 96.7 us, 1.0 sy, 0.0 ni, 2.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu24 : 0.0 us, 0.0 sy, 0.7 ni, 99.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu25 : 0.0 us, 0.0 sy, 3.0 ni, 97.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu26 : 0.0 us, 0.0 sy, 1.3 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu27 : 0.0 us, 0.0 sy, 4.0 ni, 96.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu28 : 0.0 us, 0.0 sy, 1.7 ni, 98.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu29 : 0.0 us, 0.0 sy, 1.7 ni, 98.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu30 : 0.0 us, 0.0 sy, 1.7 ni, 98.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu31 : 0.0 us, 0.0 sy, 1.0 ni, 99.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu32 : 0.0 us, 0.0 sy, 0.7 ni, 99.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu33 : 0.0 us, 0.0 sy, 1.7 ni, 98.3 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu34 : 0.0 us, 0.0 sy, 2.0 ni, 98.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu35 : 0.0 us, 0.0 sy, 1.0 ni, 99.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st %Cpu36 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st ffmpeg was sent with -threads 0 *I also tried sending ffmoeg with -threads 500- no difference

  Read the article

• Pxe net install Centos with Static IP

  - by Stu2000

  I seem to be unable to perform a kickstart installation of centos5.8 with a netinstall. It correctly gets into the text installer, but keeps sending out a request for the dhcp server and failing. I have tried to manually set the IP everywhere. Here is my pxelinux.cfg file DEFAULT menu PROMPT 0 MENU TITLE Ubuntu MAAS TIMEOUT 200 TOTALTIMEOUT 6000 ONTIMEOUT local LABEL centos5.8-net kernel /images/centos5.8-net/vmlinuz MENU LABEL centos5.8-net append initrd=/images/centos5.8-net/initrd.img ip=192.168.1.163 netmask=255.255.255.0 hostname=client101 gateway=192.168.1.1 ksdevice=eth0 dns=8.8.8.8 ks=http://192.168.1.125/cblr/svc/op/ks/profile/centos5.8-net MENU end and here is my kickstart file: # Kickstart file for a very basic Centos 5.8 system # Assigns the server ip: 192.211.48.163 # DNS 8.8.8.8, 8.8.4.4 # London TZ install url --url http://mirror.centos.org/centos-5/5.8/os/i386 lang en_US.UTF-8 keyboard us network --device=eth0 --bootproto=static --ip=192.168.1.163 --netmask=255.255.255.0 --gateway=192.168.1.1 --nameserver=8.8.8.8,8.8.4.4 --hostname=client1-server --onboot=on rootpw --iscrypted $1$Snrd2bB6$CuD/07AX2r/lHgVTPZyAz/ firewall --enabled --port=22:tcp authconfig --enableshadow --enablemd5 selinux --enforcing timezone --utc Europe/London bootloader --location=mbr --driveorder=xvda --append="console=xvc0" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work part /boot --fstype ext3 --size=100 --ondisk=xvda part pv.2 --size=0 --grow --ondisk=xvda volgroup VolGroup00 --pesize=32768 pv.2 logvol swap --fstype swap --name=LogVol01 --vgname=VolGroup00 --size=528 --grow --maxsize=1056 logvol / --fstype ext3 --name=LogVol00 --vgname=VolGroup00 --size=1024 --grow %packages @base @core @dialup @editors @text-internet keyutils iscsi-initiator-utils trousers bridge-utils fipscheck device-mapper-multipath sgpio emacs Here is my dhcp file: ddns-update-style interim; allow booting; allow bootp; ignore client-updates; set vendorclass = option vendor-class-identifier; subnet 192.168.1.0 netmask 255.255.255.0 { host tower { hardware ethernet 50:E5:49:18:D5:C6; fixed-address 192.168.1.163; option routers 192.168.1.1; option domain-name-servers 8.8.8.8,8.8.4.4; option subnet-mask 255.255.255.0; filename "/pxelinux.0"; default-lease-time 21600; max-lease-time 43200; next-server 192.168.1.125; } } Is it impossible to prevent it asking for a dynamic ip before trying to install from the net? Perhaps there is an error in of my files? My dhcp server is set to ignore client-updates, and is set to only works with one mac address whilst testing.

  Read the article

• mongodb : Can create new thread on FreeBSD?

  - by user197739

  We experienced some strange thing in our mongodb gridfs platform. The platform actually is a bi Xeon E5 (bi quad core) with 128GB of memory, running on freebsd 9 with a zfs pool dedicated for mongodb. [root@mongofile1 ~]# uname -sr FreeBSD 9.1-RELEASE our /boot/loader.conf vfs.zfs.arc_min="2048M" vfs.zfs.arc_max="7680M" vm.kmem_size_max="16G" vm.kmem_size="12G" vfs.zfs.prefetch_disable="1" kern.ipc.nmbclusters="32768" /etc/sysctl.conf net.inet.tcp.msl=15000 net.inet.tcp.keepidle=300000 kern.ipc.nmbclusters=32768 kern.ipc.maxsockbuf=2097152 kern.ipc.somaxconn=8192 kern.maxfiles=65536 kern.maxfilesperproc=32768 net.inet.tcp.delayed_ack=0 net.inet.tcp.sendspace=65535 net.inet.udp.recvspace=65535 net.inet.udp.maxdgram=57344 net.local.stream.recvspace=65535 net.local.stream.sendspace=65535 we follow the recommendation for the ulimit : [root@mongofile1 ~]# su - mongodb $ ulimit -a cpu time (seconds, -t) unlimited file size (512-blocks, -f) unlimited data seg size (kbytes, -d) 33554432 stack size (kbytes, -s) 524288 core file size (512-blocks, -c) unlimited max memory size (kbytes, -m) unlimited locked memory (kbytes, -l) unlimited max user processes (-u) 5547 open files (-n) 32768 virtual mem size (kbytes, -v) unlimited swap limit (kbytes, -w) unlimited sbsize (bytes, -b) unlimited pseudo-terminals (-p) unlimited This server have a twin (same config exactly) for ReplSet in other data center and we have a virtualized arbiter. Some time, almost 3 days, the process of mongodb exit. The problem begin with: Fri Nov 8 11:27:31.741 [conn774697] end connection 192.168.10.162:47963 (23 connections now open) Fri Nov 8 11:27:31.770 [initandlisten] can't create new thread, closing connection Fri Nov 8 11:27:31.771 [rsHealthPoll] replSet member mongofile2:27017 is now in state DOWN Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.162:47968 #774702 (20 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.161:28522 #774703 (21 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.164:15406 #774704 (22 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.163:25750 #774705 (23 connections now open) Fri Nov 8 11:27:31.810 [initandlisten] connection accepted from 192.168.10.182:20779 #774706 (24 connections now open) Fri Nov 8 11:27:31.855 [initandlisten] connection accepted from 192.168.10.161:28524 #774707 (25 connections now open) Fri Nov 8 11:27:31.869 [initandlisten] connection accepted from 192.168.10.182:20786 #774708 (26 connections now open) and after many "can create new thread" [root@mongofile1 /usr/mongodb]# tail -n 15000 mongod.log.old |grep "create new thread"|wc 5020 55220 421680 and finish by a magnificent Fri Nov 8 11:30:22.333 [rsMgr] replSet warning caught unexpected exception in electSelf() pure virtual method called Fri Nov 8 11:30:22.333 Got signal: 6 (Abort trap: 6). Fri Nov 8 11:30:22.337 Backtrace: 0x599efc 0x8035cb516 0x599efc <_ZN5mongo10abruptQuitEi+988> at /usr/local/bin/mongod 0x8035cb516 <_pthread_sigmask+918> at /lib/libthr.so.3 Extract of mongodb from top 78126 mongodb 77 20 0 1253G 1449M sbwait 0 0:20 0.00% mongod If I restart the process when it crash, the problem is fixed for almost 3 days. Has anyone seen this before, or know of a fix?

  Read the article

• Exchange-Server Query

  - by Rudi Kershaw

  First, a little background. I've recently been taken on as a web and software developer for a small company, who has no other in-house IT support. They've been asking my opinion on lots of IT subjects that are quite far out of my comfort zone. I'm definitely not a network admin. Their IT consultancy contractor is pushing them to upgrade their dedicated exchange server, even though it seems like the one they currently have has a lot of life left in it and is running problem free. They say it's "coming to the natural end of it's life". They want to install a monster with a Xeon E5-2420, 32GB RAM, 2x 1TB HDDs, Windows Server 2012 and Microsoft Exchange 2010. They want to charge a small fortune for it. Basically, this system seems massively over the top seeing as it won't be doing anything else other than running as an exchange server for a company with less than 25 email accounts. My employers also have a file server system in-house that hosts three web apps, an SQL server, their local domain, print server and shared folders. That machine is using the same specs as the proposed new one, and it is barely using any of it's potential. I asked if Microsoft Exchange 2010 could be installed on their file server, but they said that MS Exchange can't run on the same system as an SQL server because for some reason they will eat up each others resources (even though the SQL server isn't touching 1% of the current system's CPU or RAM). My question is really, are they trying to rip my employers off? Could MS Exchange be installed on their other server (on a virtual instance or not), or does the old one even need replacing at all? Going with their current suggestion will cost the company in excess of £6k, and it seems entirely unnecessary. I apologies, because I know this is probably a little thin on details, but if I carry on I could end up writing a massive essay that no-one will want to read. I've been doing my research, but I'm not knowledgeable enough make any hard decisions. Let me know if you need any more details. Thank you for any help you can offer. Further Details: The new exchange would need to support Outlook Web App, 25 users, a few public mailboxes, and email exchange with Blackberries.

  Read the article

• On ESXi, guest machines hang for significant intervals compared to real machines. How can I fix this?

  - by Tarbox

  This is ESXi version 5.0.0. We plan on upgrading to 5.5 eventually. I have four code profiles, two taken on a real, unvirtualized machine, two taken on a virtual machine. Ordering the list of subroutines by time spent in each one, the two real profiles are practically identical. The two virtual profiles are different from each other and from the real profiles: a subset of subroutines are taking a lot more time on the virtual machines, and the subset is different for each run. The two virtual profiles take a similar amount of time, which is 3 times the amount of time the real profiles take. This gross "how long does it take?" result is consistent after hundreds of tests across three different virtual machines on two different host machines -- the virtual machine is just slower. I've only the code profiling on the four, however. Here's the most guilty set of lines: This is the real machine: 8µs $text = '' unless defined $text; 1.48ms foreach ( split( "\n", $text ) ) { This is the first run on the virtual machine: 20.1ms $text = '' unless defined $text; 1.49ms foreach ( split( "\n", $text ) ) { This is the second run on the virtual machine: 6µs $text = '' unless defined $text; 21.9ms foreach ( split( "\n", $text ) ) { My WAG is that the VM is swapping out the thread and then swapping it back in, destroying some level of cache in the process, but these code profiles were taken when the vm in question was the only active vm on the host, so... what? What does that mean? The guest itself is under light load, this is a latency problem for my users rather than throughput. The host is also under a light load, if I knew what resources to assign where, I could do it without worrying about the cost. I've attempted to lock memory, reserve cpu, assign a restrictive affinity, and disable hyperthread sharing. They don't help, it still takes the VM 2-4x the amount of time to do the same thing as the real machine. The host the tests were run on is 6x2.50GHz, Intel Xeon E5-26400 w/ 16gigs of ram. The guest exhibits the same performance under a wide combination of settings. The real machine is 4x2.13GHz, Xeon E5506 w/ 2 gigs of ram. Thank you for all advice.

  Read the article

• Wireless cuts out on Toshiba Satellite S7208

  - by alecRN

  I recently got a Toshiba Satellite L875-S7208 with Windows 7 preinstalled. I installed Ubuntu 12.04 LTS dual boot to the same Windows partition. However, usually 15 minutes or less after booting, the wifi connection dies. Here's some hopefully relevant information: lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: i2c-i801 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8211] Kernel driver in use: rtl8192ce Kernel modules: rtl8192ce 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Subsystem: Toshiba America Info Systems Device [1179:fb37] Kernel driver in use: r8169 Kernel modules: r8169 lsmod Module Size Used by snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224066 1 joydev 17693 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 arc4 12529 2 snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 87692 0 serio_raw 13211 0 rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device sparse_keymap 13890 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev mac_hid 13253 0 mei 41616 0 wmi 19256 0 soundcore 15091 1 snd i915 472941 3 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 cfg80211 205544 2 rtlwifi,mac80211 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 ums_realtek 18248 0 uas 18180 0 usb_storage 49198 1 ums_realtek dmesg | grep firmware [ 15.692951] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 16.240881] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 452.419288] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail. [ 458.572211] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 465.440640] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 472.337617] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 479.175471] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 485.978582] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 492.764893] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 499.579348] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 506.386934] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 513.209545] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 519.991365] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 526.778375] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 533.629695] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 540.426004] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 547.238125] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 554.024434] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 560.854794] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 567.678160] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 574.494666] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 581.336653] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 588.157710] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 595.221122] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 602.047429] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 608.829534] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 615.639079] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 622.454991] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 629.273231] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 636.056613] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 642.858096] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 649.640753] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 657.184094] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 664.008018] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 670.838639] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 677.675418] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 684.507255] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 691.310994] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 698.095325] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 704.914509] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 711.725178] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin uname -r 3.2.0-29-generic ifconfig eth0 Link encap:Ethernet HWaddr 4c:72:b9:59:6c:61 inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe59:6c61/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:0 overruns:0 frame:0 TX packets:2762 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3671147 (3.6 MB) TX bytes:335133 (335.1 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:515 errors:0 dropped:0 overruns:0 frame:0 TX packets:515 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:83153 (83.1 KB) TX bytes:83153 (83.1 KB) wlan0 Link encap:Ethernet HWaddr 74:e5:43:32:47:95 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32958 (32.9 KB) TX bytes:10431 (10.4 KB)

  Read the article

< Previous Page | 1 2 3 4 5  | Next Page >