Search Results

Search found 8378 results on 336 pages for 'sharepoint 2003'.

Page 4/336 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Windows Server 2003 Terminal Server does not give out all available licenses

    - by Erwin Blonk
    I installed the Terminal Server role in Windows Server 2003 Standard 64-bits. Still, only 2 connections are allowed. The License Manager says that there are 10 Device CALs available, which is correct, and that none are given out. For good measure I let the server reboot, to no effect. Before this, there was another server (same Windows, except that it is 32 bits) active as a licensing server. I removed the role first and then then added it to the new server. I then removed the Terminal Server Licensing Server component off the old one and added it to the new one. After that, I added to licenses. When that didn't give the required result, I rebooted to new server. Still, the new server, with licenses and all, acts as if it has the 2 license RDP. The server are all stand-alone, there is no active directory been set up. Both servers are in different workgroups. Update (4/12/10): The server has changed the entries in the Terminal Server Licensing a few times. After installing the licenses it added an entry of which the exact phrasing I forgot but it was about temporary Windows 2003 device licenses. Later it added Windows Server 2003 - TS Per Device CAL. The temporary held 2 licenses (standard RDP licenses, I think) and the other 10. At some point, seemingly unrelated from the testing we did, it used a licenses from the new pool. This morning, 2 licenses were used from the pool of 10 and only 1 from the temporary/RDP pool (I wish I had screenshots to show, it changed every few hours oir so it seems). Although I had already activated the server over the internet, and re-activated it, I decided to go through the whole procedure by phone. Long story short, here is what it says now: Existing Windows 2000 Server, type:built-in [no licenses used, I add for for sake of being complete] Windows Server 2003 - Terminal Server Per Device CAL Token, type:open [none of 10 used] Windows Server 2003 - TS Per Device CAL, type:open [3 of 10 used] As I tried to explain, this is the end result after a few changes, most of which I can't directly connect to any action from my part. Only going to the activation procedure by phone seemed to directly effect the TS, resulting in the above configuration. Still, it is impossible to connect with more than 3 people, which is 1 up from the 2 that could connect yesterday. TS does say 7 licenses are avaible. Yet it won't give them out.

    Read the article

  • Truly understand the threshold for document set in document library in SharePoint

    - by ybbest
    Recently, I am working on an issue with threshold. The problem is that when the user navigates to a view of the document library, it displays the error message “list view threshold is exceeded”. However, in the view, it has no data. The list view threshold limit is 5000 by default for the non-admin user. This limit is not the number of items returned by your query; it is the total number of items the database needs to read to calculate the returned result set. So although the view does not return any result but to calculate the result (no data to show), it needs to access more than 5000 items in the database. To fix the issue, you need to create an index for the column that you use in the filter for the view. Let’s look at the problem in details. You can download a solution to replicate this issue here. 1. Go to Central Admin ==> Web Application Management ==>General Settings==> Click on Resource Throttling 2. Change the list view threshold in web application from 5000 to 2000 so that I can show the problem without loading more than 5000 items into the list. FROM TO 3. Go to the page that displays the approved view of the Loan application document set. It displays the message as shown below although I do not have any data returned for this view. 4. To get around this, you need to create an index column. Go to list settings and click on the Index columns. 5. Click on the “Create a new index” link. 6. Select the LoanStatus field as I use this filed as the filter to create the view. 7. After the index is created now I can access the approved view, as you can see it does not return any data. Notes: List View Threshold: Specify the maximum number of items that a database operation can involve at one time. Operations that exceed this limit are prohibited. References: SharePoint lists V: Techniques for managing large lists Manage large SharePoint lists for better performance http://blogs.technet.com/b/speschka/archive/2009/10/27/working-with-large-lists-in-sharepoint-2010-list-throttling.aspx

    Read the article

  • Windows 2003 R2 zip program blocking EXE file

    - by Harvey Kwok
    I have a Windows 2003 R2 Enterprise Edition SP2 32-bit machine with all latest patch (as of 1-6-2011). It's a VM. I have a zip file, including a pdf file, a txt file and a exe file. If I copy the zip file onto the machine via a shared network drive, I can unzip all the files properly without problems. If I put the zip file on my web server and then I download it from there, I can only unzip the pdf file and txt file. The exe file is silently ignored. I searched the web and found somebody reporting similar issue on XP. If I right click on the zip file downloaded from the web server, at the bottom of the general page, it has a warning message saying that "This file came from antoher computer and might be blocked to help protect this computer" I understand that I can solve the problem by simply clicking the "Unblock" button and extract the file again. The things that bothering me is that why the warning message says "might be blocked"? I tried downloading the same zip file from the same web server on to my Windows 7 box with latest patch. It also shows the same warning message. However, even with the warning message, I can extract all the files properly without clicking the "Unblock" button. Is it a bug in Windows 2003 R2 SP1? Is there any security settings controlling this? How likely will the end user seeing this problem? I want to dig into this because I am worrying people downloading my zip file from my web server might see similar problems. The first thought coming to the user's mind will be the zip file is somehow corrupted. Honestly, I didn't know this "Unblock" feature in Windows before I run into this problem. EDIT I just tried it on another Windows 2003 R2 SP1 machine. The zip program doesn't block the EXE file on that machine either. Both Windows 2003 R2 SP1 machines are joining to the same forest.

    Read the article

  • Office 2003 Service Pack 3- Not able to install

    - by kabirrao
    I am trying to install Office 2003 SP3 on a windows 2003 EE server (used as a terminal server) which already have office 2003 SP2. I am getting an error that says "Update can not be applied". Below are the eventviewer entries for Application: _ Event Type: Warning Event Source: MsiInstaller Event Category: None Event ID: 1015 Date: 1-2-2010 Time: 5:51:22 User: Domain\domainadmin Computer: TER01 Description: Failed to connect to server. Error: 0x800401F0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. _ Event Type: Information Event Source: MsiInstaller Event Category: None Event ID: 11708 Date: 1-2-2010 Time: 5:52:23 User: Domain\domainadmin Computer: TER01 Description: Product: Microsoft Office Professional Edition 2003 -- Installation failed. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 7b 39 30 31 31 30 34 30 {9011040 0008: 39 2d 36 30 30 30 2d 31 9-6000-1 0010: 31 44 33 2d 38 43 46 45 1D3-8CFE 0018: 2d 30 31 35 30 30 34 38 -0150048 0020: 33 38 33 43 39 7d 383C9} _ Event Type: Information Event Source: McLogEvent Event Category: None Event ID: 257 Date: 1-2-2010 Time: 5:52:23 User: NT AUTHORITY\SYSTEM Computer: TER01 Description: Would be blocked by access protection rule (rule is in warn-only mode) (Common Standard Protection:Prevent common programs from running files from the Temp folder).

    Read the article

  • Server 2003 and SSL Certificates

    - by Keith Stokes
    I have a Windows 2000 domain with dozens of Windows 2000 servers and a few 2003 servers. Each server runs a custom app talking to a 3rd party utilizing self-signed certificates. To help troubleshooting we've created a custom test app. The 2000 servers are able to talk within seconds. The 2003 servers take anywhere from 10-30 seconds using a domain account and much less, usually under 5 seconds using a local account. The only exception to the local account performance is a new account, which is slow initially then faster. If you leave the test app open and reconnect repeatedly it talks in seconds. If you leave it open for sometime between 1 and 2 hours, it reverts back to the previous 10 seconds, so obviously something is caching. Installing the destination certificates in the local 2003 server store makes no difference. I've installed the certificates in AD and that apparently makes domain accounts work in 9-12 seconds, vs 30 seconds that was regular before. Manually clearing the certificate store on the 2003 server makes no difference. I'm at a loss as to where the certs might be cached and if I'm using some sort of domain certificate store that's hiding from me.

    Read the article

  • Virtualize SBS 2003 - P2V vs migrating to new VM

    - by jlehtinen
    I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

    Read the article

  • Another Exchange 2003 to Exchange 2010 mail flow issue

    - by Ryan Roussel
    During a migration recently, we came across another internal mail routing issue.  The symptoms were identical to my previous post about Exchange internal mail routing.  Mail was flowing from 2010 to 2003, from 2010 to the internet, but not from 2003 to 2010.   I went through the normal check list looking at permissions, DNS, and the routing group connectors.  I verified that both servers listed in the routing group connectors were the routing master in their respective routing groups through the 2003 ESM.  I also verified that inheritable permissions were enabled for the Exchange 2003 server object in the schema.  No luck with either.   For my previous post about this issue in which inheritable permissions were the culprit: Exchange 2010, Exchange 2003 Mail Flow issue   And for Routing Group issues: Exchange 2007 Routing Group Connector Mayhem   I finally enabled logging on the SMTP virtual server on Exchange 2003 and the Default Receive Connector on 2010 and sent a few test e-mails where I found 2003 was having issues authenticating to 2010.  By default 2003 uses Exchange Server Authentication to communicate to 2010. The exact error was: 4.7.0 Temporary Authentication Failure which was found in the SMTP logs on the Exchange 2003 side   After scouring based on this error, I found the solution:   The Access this computer from the network user rights in the local computer policy on the Exchange 2010 server were changed from the default.  The network administrator had modified the Default Domain policy and changed this user right assignment to only list Domain Users.   The fix was to clear this setting in the Default Domain policy,  force gpupdate to refresh the group policy settings, then ensure the appropriate users and groups were listed.   This immediately fixed the problem and the Exchange 2003 server was able to route mail to the Exchange 2010 mailboxes.   The default user rights assignments for Access this computer from the network On Workstations and Servers: Administrators Backup Operators Power Users Users Everyone On Domain Controllers: Administrators Authenticated Users Everyone More can be found here: http://technet.microsoft.com/en-us/library/cc740196(WS.10).aspx

    Read the article

  • Deploying Excel 2003 VSTO Workbook using Sharepoint for versioning control

    - by KClough
    I have an excel 2003 vsto workbook that I would like to make available via sharepoint for version control. Ideally it could be checked in/out by non-developers for tweaking excel equations, and I would be able to deploy the compiled dlls somewhere else when I need to update the managed VSTO code. I understand I may need to use some clickonce functionality as well so when a user first views the sheet they get all the necessary full-trust permissioning. Also, it is my understanding that for a user to use the vsto functionality in an excel 2003 vsto workbook, they must have the compiled dll in thier GAC, is this true? When testing I get trust exceptions otherwise.

    Read the article

  • Windows Server 2003 Licensing

    - by Phil
    Hi all, I'm looking to get a Windows Server 2003 box in the middle of my linux network. :( I'm just concerned about CAL licensing for it. No devices will access any network server function of Windows Server 2003. I don't need Windows for DHCP or DNS or file and print sharing. I have linux boxes to do that! xD I just need a box running Windows (of some variety) to host those few apps that have to run on Windows like my AV management console. In short do I need any CALs for my server if its not acting as server itself. I think Windows Server 2003 comes with 5 CALs which can be per user for the admins to use RDP? Thanks, Phil

    Read the article

  • Windows-Server-2003 setup on Dell-PowerEdge R310 is hanging [closed]

    - by Robert Rose
    Possible Duplicate: Problems installing OS on Dell PowerEdge R410 I am trying to configure a Dell PowerEdge R310 server with Windows Server 2003. I've already configured the two hard drives as RAID1. The HD controller is PERC H700 Integrated and Adapter. Trying to stay with Windows Server 2003 on this fairly new server to save on cost and keep the configuration the same as my old server, which has been running like a champ for five years. Problem: During the OS installation, after everything has been copied from the installation CD, the installation hangs at a window labeled 'Windows Setup' with the message 'Setup is starting Windows' at the bottom. I'm wondering if this is a driver problem and if so, where can I get the drivers for the R310 or where can I get the media for the latest version of Windows Server 2003 which may include the necessary drivers? Will certainly appreciate some help here.

    Read the article

  • Add server 2008 to 2003 domain schema upgrade failed

    - by Ken
    I'm trying to add a server 2008 r2 server to an existing 2003 domain (upgraded to 2003 functionality). I've followed the steps from microsoft which are clarified by this post: 2003 DC AD upgrade to 2008 on second server migration plan While running adprep /forestprep I lost my connection and wasn't able to resume or remote control that session, so I couldn't see the end result of the command. Rerunning adprep /forestprep indicates that the process has already been completed successfully. After finishing the rest of the steps (/domainprep ... and /gpprep, etc), the 2008 server won't join. The error message is the same "you need to run forestprep first" So the situation I'm in is that I can't rerun /forestprep, but my Registry key still reads schemaVer=30. Should I have staged forest upgrades? Any ideas how to get my schema ver to 44 at this point?

    Read the article

  • Remote site AD design (2003)

    - by Boy Mars
    A remote site has about 25 of our 50-ish employees. They have their own AD domain presently (2003) but I want to look at getting them onto the same global domain for ease of access/administration. The remote site has a VPN link but line speeds are very poor. I am already aware of tools like ADMT and have done a few migrations in the past (NT/2003 domains), but this is the first time I have the luxury of designing how this domain is organised. So I'm looking for tips on good AD design; would a remote site be better served as a sub-domain? would this reduce traffic? I am only currently looking at 2003 since only existing machine will be used.

    Read the article

  • Windows 2008 R2 DS in 2003 domain?

    - by 3molo
    Hi, Having a master domain controller running Windows 2003, and now I'd like to set up a new domain controller on a branch office. I really only have access to licenses for Windows 2008 R2 (through licensing.microsoft.com), so question is if a newly installed Windows 2008 Standard R2 can become a domain controller in the existing (2003) domain? First I tried adprep /forestprep on the newly installed 2008, but it complained about not being a domain controller. I then tried dcpromo, but it too complained about it. According to MS documentation, it seems I have to run 'adprep /forestprep' on the master domain controller, and adprep is located in 2008 installation DVD. Am I on the right track? Is the correct way to mount the 2008 installation dvd into the existing 2003 master controller, and run 'adprep /forestprep' on it there? Will I be able to run dcpromo on the 2008 once that has been completed? Thanks,

    Read the article

  • Exchange 2003 HTTP Account Error

    - by Ryaner
    We are trying to get one of our users connected to our Exchange 2003 server using the HTTP method as they already have an existing Exchange account on another server. The setup goes through and they appear to get connected fine however none of the subfolders are listed. Instead we get one folder of "Error-Pls file a Bug". The usual Google search just throws up nothing useful. Does anyone know how to fix this? Or has anyone actually gotten Outlook (2003 or 2007) to connect to an Exchange 2003 server?

    Read the article

  • Error when running adprep32 /rodcprep, trying to add a 2008 domain controller to a 2003 domain

    - by virtuist
    I'm trying to migrate a Small Business Server 2003 to Server 2008 domain. The problem is when I run the adprep32 /rodcprep command as specified as the final step in Step 3 of this article: http://www.experts-exchange.com/Software/Server_Software/Email_Servers/Exchange/A_2881-Migrate-Small-Business-Server-2003-to-Exchange-2010-and-Windows-2008-R2.html I get an error "Adprep could not contact a replica for partition..." which is described in detail here: http://support.microsoft.com/kb/949257 I've also attached the AdPrep.log file for full details. So when I try to run DCPromo on my new Server 2008 PDC (it's not the PDC yet, but want it to be soon), I get an error saying that /rodcprep hasn't ran so there could be errors if I continue. Anyone ran into this or have any suggestions on how to help? Can Dsmgmt be ran on server 2003 to help solve this? Assuming it's a partition error.

    Read the article

  • Baffling Exchange 2010 issue , Outlook 2003

    - by Nick Weber
    Recently we upgraded from Exchange 2003 to Exchange 2010. The Exchange 2003 server is still up and active with a handful of users still there we are planning on migrating. Also we have mobile devices and a Blackberry BES server setup publishing to Exchange 2010 public folders free busy. The unfortunate issue is majority of our clients are still Outlook 2003. The issue seems to be hit and miss but sometime clients cannot view other client’s calendars. They get (cannot refresh free/busy) when they add another user and check their available times. This is also true with booking resources (conference rooms) . One thing we noticed is that the Blackberry BES seems to have created its own free/busy folders, so we have some users who use the BES on free/busy folder and other users who don’t use the BES on other free/busy folders. If any of the clients log-in via “Exchange 2010” web-access or with a Outlook 2007 client they can view the calendaring just fine. Thanks for your help Nick @Toshana

    Read the article

  • MLGPO for Windows Server 2003 R2?

    - by 5graeham5
    Is there something like MLGPO (Multiple Local Group Policy Objects) for Windows Server 2003 R2? I have a 2003 Terminal Server that isn't part of a domain/AD and I'm trying to set local group policies which applies only to certain users and/or groups and the policies differ between those entities. I wanted to avoid using the file permissions trick for on C:\WINDOWS\system32\GroupPolicy as that's an all-or-nothing approach. I can't upgrade this box to Windows Server 2008 as the software used is only supported and only works on 2003. Are there any third-party tools to achieve this?

    Read the article

  • Access or import an Outlook 2003 .pst file without Outlook

    - by Nobler
    I have a 450 meg .pst file (MS Outlook 2003 backup file) saved from a PC before it crashed. I would like to break it up into its components i.e. Save attachments to folders on my PC Paste text-emails into a word processor, etc. But I don't want to buy MS Office Professional 2003 or later solely for importing the .pst into MS Outlook 2003+. Outlook Express cannot import .pst files, only Outlook “proper” can. Is there some free email client out there, e.g. Thunderbird, that can import .pst files? Or is there some other way to access the 450meg file?

    Read the article

  • Utility to listen on port (Windows 2003 Server)

    - by Gero
    Hi, I need to validate some network connectivity from machine X to a Windows 2003 Server machine. To be able to do so I'm looking for a simple utility that I can run on the Windows 2003 server that will listen on a specified port. It does not have to do anything else. When it listens on the specified port I can do a telnet to that port from machine X and check if all firewalls are open. The Windows 2003 Server machine is already a production machine so I cannot install all kinds of stuff. At this stage we want to ensure that all network connectivity is in place before we do the installation of the 'real' application that will listen that port (don't want to wast time debugging network connectivity issues when we do the actual deployment of the new application. The utility should be a simple command line utility that does not require any installation. What utilities do you recommend? Thanks, Gero

    Read the article

  • How to view dirty page count in Windows Server 2003

    - by Mark Wilkins
    Is there a way to view the number of dirty pages (cached file pages that need to still be written to disk) in Windows Server 2003? In Windows 7, for example, I can use Performance Monitor and use the "Dirty Pages" counter (one of the cache counters). This counter does not seem to be available in Server 2003. Also on Windows 7 (and other later systems), I can use Sysinternals RAMMap and effectively see the dirty pages on a file-by-file basis. Is there something similar for Server 2003?

    Read the article

  • Reset my windows server 2003

    - by Tim Thoirp
    I was recently given an HP Proliant Server from a friend as a gift. It has Windows Server 2003 installed on it. When I go to boot the system however to log in to Windows Server 2003 it requires an Admin password. I can't figure out the password and my friend doesn't know it either as it has been years since hes used the machine. I don't care about any of the data on the machine I just want to have a new clean version of Windows server 2003 running on it. Any advice would be helpful? And no I don't want to pay for a password cracking tool. Thanks

    Read the article

  • "Service Unavailable" when browsing to static HTML page in non-application IIS website on Windows 2003 (possibly SharePoint WSS 2.0 related?)

    - by Jordan Rieger
    Background: My client has an old Pentium III Windows 2003 server whose 16/36 GB disks are dying. On it he has a database-driven web site and email application that needs further customization by a developer (me). First we need to get it working on the new server. The original developer is no longer available to provide a system setup guide. So my client got a tech who imaged the old drives over to the new server and managed to get it booting. But the IIS-driven site no longer works. In fact it seems that IIS itself does not work. Problem: Service Unavailable when attempting to browse from the server itself to the URL for a local Web Site called test which I setup in IIS to serve a single static index.htm file. This I did to isolate the problem, and eliminate the client's application from the equation. The site is setup on port 80 with the host header "test.myclientsdomain.com", and I used the etc\hosts file to point that host at the local IP. I know the host entry took effect because I can ping it. When doing an iisreset, I get: Attempting start... Restart attempt failed. IIS Admin Service or a service dependent on IIS Admin is not active. It most likely failed to start, which may mean that it's disabled. Despite this message, the services all stay in the Started state. The only relevant System event logs I found are: Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1002 Date: 11/4/2012 Time: 11:04:47 PM User: N/A Computer: ALPHA1 Description: Application pool 'DefaultAppPool' is being automatically disabled due to a series of failures in the process(es) serving that application pool. Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1039 Date: 11/4/2012 Time: 11:13:12 PM User: N/A Computer: ALPHA1 Description: A process serving application pool 'DefaultAppPool' reported a failure. The process id was '5636'. The data field contains the error number. Data: 0000: 7e 00 07 80 ~.. And one Application event log: Event Type: Error Event Source: Windows SharePoint Services 2.0 Event Category: None Event ID: 1000 Date: 11/4/2012 Time: 11:34:04 PM User: N/A Computer: ALPHA1 Description: #50070: Unable to connect to the database STS_Config on ALPHA2\SharePoint. Check the database connection information and make sure that the database server is running. That last log tells me that the tech may have initially tried to have both the old and the new server running, by renaming the new server from ALPHA1 to ALPHA2. And perhaps SharePoint grabbed onto that change, and now can't tell that the machine name has been switched back to the old ALPHA1. But why would SharePoint interfere with a static IIS web site serving a single HTML file? The test site is not even within an Application pool (I clicked the Remove button.) What I have tried/eliminated: No relevant services seem to be disabled: IIS Admin, WWW Publishing, Sharepoint Timer Giving Full Control to All Users/Everyone on the c:\inetpub\test folder serving my test site. I can connect to and query the local SharePoint config database (ALPHA1\SHAREPOINT\STS_CONFIG) from SSMS. But when I try to do stsadm -o setconfigdb -connect -databaseserver ALPHA1\SHAREPOINT it tells me The SharePoint admininstration port does not exist. Please use stsadm.exe to create it. And when I do that, using the port 9487 specified in the IIS SharePoint Admin site config, it tells me the port is already in use. Needless to say, simply browsing to the admin site gives me a similar error about being unable to reach the config database. I didn't want to go further down the SharePoint path as it may be completed unrelated to my IIS issue, and I don't even know yet if SharePoint is required for this application to work. The app itself is ASP.Net/C#/Silverlight and a little MS Word integration (maybe that's where the SharePoint stuff comes in.)

    Read the article

  • Office 2003 won't install with proper CD KEY

    - by MadBoy
    I wanted to reinstall Office 2003 Pro. I retrieved the key with NirSoft ProduKey, confirmed with Jelly Bean Windows Key Finder and the key is the same. I've tried 3 different Office 2003 PRO CD's and it still won't install because it's saying key is bad, i even tried with different key from other computer and it also won't install. Anyone can suggest some workaround?

    Read the article

  • Migrating from VBA Excel 2003

    - by Krazy_Kaos
    I have a series of big excel files that work like a program, but I hate beeing tied up (stuck in VBA for excel 2003), so... Whats the best way to implement a gui over a excel vba program (office 2003)? (are there any tools for that... I want to move away from the office suite, but still have it in the background) Or what's the easiest alternative for migrating this code to a more open language. Any ideias?

    Read the article

  • Installing Windows 2003 over remote DRAC 4

    - by Delli
    I'm trying to install windows 2003 over a DRAC 4 console session by using a ISO file. But it keeps freezing during the GUI installation then when login back Windows Setup says some files not found and setup won't continue. What's the best approach to install Windows 2003 over a DRAC 4 console session?

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >