Search Results

Search found 19350 results on 774 pages for 'address book'.

Page 407/774 | < Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >

  • Bridging and iptables SNAT conflict

    - by sad_admin
    Hello I am working on a setup here and have it working with one minor exception. Devices on one side of my bridge aren't getting SNAT'd to the Internet. The Diagram / Overview: Primary_Network (Site_A) | | Internet ------- Linux_Bridge_GW (GW) | | Secondary/CoLo Site (Site_B) Here is the setup: 1.) Site_A has all the production servers and workstations. 2.) Site_B has a set of servers that we would like to fail-over to and also serve our internet facing services from. 3.) GW has two interfaces that are trunked and carrying the appropriate VLAN traffic (allow layer-2 propagation of traffic between sites) //this all works perfectly fine. 4.) The problem that is being encountered is, hosts from Site_B have their default GW at Site_A (same subnet) GW does not have IPs on the VLANs that are being passed. 5.) All hosts at Site_A can reach the Internet without problem. 6.) GW has an addresses on a subnet that is ONLY for Internet destined traffic. (This was done so that Websense would not have to parse unnecessary traffic. We use this VLAN as the monitor port's source on the switch where Websense is sitting). What I think is happening: 1.) Packet/Frame comes in on physdev at Site_B destined for Internet. 2.) Kernel sees packet, and forwards it out the other side of the bridge to that host's default GW. 3.) Site_A (containing core-network's Default-GW) sees that packet is destined for a host it doesn't know about, so it sends it to it's default GW (the linux bridge, since it's Internet bound). 4.) The kernel says "Hey, I've seen you before" and therefore doesn't do SNAT'ing on the packet and sends it out to the Internet where it's black-holed. Why I think it's happening: 1.) A tcpdump on the internet facing NIC shows the packet leaving the interface with the private address as it's source. What I would like: 1.) Have the packet SNAT'd. 2.) Something like the below would be awesome a.) packet comes in from Site_B b.) kernel sees that the packet is NOT destined for itself or any private address c.) kernel says "OK, well since you're destined for the Internet I'm going to send you out this interface rather than forward you to your normal default GW that's WAAAY over there." d.) packet comes in from internet and is sent out the appropriate bridge physdev depending on which site the host it's destined for is at. Thanks for any assistance or guidance that you are willing to offer. Best Regards, Sad Admin

    Read the article

  • Is there a way to detect which port on an ethernet switch a device is connected to?

    - by banno
    Since the wall jack is typically always connected to the same port on the switch I would like to be able to know which device is connected at a specific location. In my case I am talking about printers. I have code to go out on the network and find the IP Address of all of my printers, but would like to be able to update a server based on a printer being swapped out of a location for maintenance or repair. Is there a method for determining a port connection?

    Read the article

  • unable to connect site to different port

    - by JohnMerlino
    I have a domain was registered at godaddy named http://mysite.com/. I logged into godaddy and I went to All Products Domains Domain Management. I clicked on the appropriate domain and it took me to the Domain Details page. I clicked Launch under DNS Manager and it took me to the Zone File Editor. I noticed that notify.mysite.com was pointing to an IP address pointing to a dead server, so I switched it to an operating server. Then I pinged the domain to see where it was pointing to and it was correctly pointing to the working server. So I copied the default configuration under sites-available: sudo cp default notify.mysite.com. And then I made some edits to it to have it point to a different document root to serve files at a different port: Listen 1740 Listen 64.135.xx.xxx:1740 #I also tried this as well: NameVirtualHost 64.135.xx.xxx:1740 <VirtualHost 64.135.xx.xxx:1740> ServerAdmin [email protected] ServerName notify.mysite.com DocumentRoot /var/www/test/public <Directory /var/www/test/public> Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> Then I enabled the virtual host. Then I went to the document root and added an index.html file with some text in it. Then I restarted apache. The restart gave no errors. Then I type the correct domain in URL: http://notify.mysite.com:1740/ and I get: Oops! Google Chrome could not connect to notify.mysite.com:1740 Somehow it took out all my other sites. Now even the ones that were responding on port 80 are no longe responding, even though I did not touch the virtual hosts for them. I get this message now: Oops! Google Chrome could not connect to mysite.com However, ping responds: ping mysite.com PING mysite.com (64.135.12.134): 56 data bytes 64 bytes from 64.135.12.134: icmp_seq=0 ttl=49 time=20.839 ms 64 bytes from 64.135.12.134: icmp_seq=1 ttl=49 time=20.489 ms The result of telnet: $ telnet guarddoggps.com 80 Trying 64.135.12.134... telnet: connect to address 64.135.12.134: Connection refused telnet: Unable to connect to remote host

    Read the article

  • OpenAM Membership module does not notify admin of new inactive accounts

    - by Eric Axley
    I am using OpenAM to authenticate users and OpenDJ as the user directory. I have enabled the membership module that allows users to self register, but I have not found any way to notify the admin that a new account needs to be approved. This seems like something that would just be a matter of entering an admin email and configuring smtp, but I have not found anywhere to enter an email address to receive these notifications. Though I have been able to send "password reset" emails so smtp is working at least.

    Read the article

  • Excel - create a list from each cell of a sheet range

    - by CharlesB
    I have a bunch of sheets in my workbook, in each one there is an email address at B6. What I want to do is to make a list with all the email addresses. I'm familiar with sheet range (all my sheets are between a sheet "first" and a sheet "last"), so I can do something like first:last!B6 to refer to the range. But what is the formula?

    Read the article

  • Looking for spam mails.

    - by apalsson
    I am looking for a bundle of spam mails to use with my experiments with Bayesian spam filtering. Is there any resource for this or does anyone have a bundle to share with me? Something around 4-6gb zip:ed would be a nice start. Feel free to filter out your own email-address, though this is for personal use and it won't be shared with anyone. Thanks.

    Read the article

  • How to troubleshoot port forwarding on Windows 7 (64 Bit) with ICS enabled?

    - by LearnCocos2D
    I want to forward some ports (1666 for perforce, 8081 for Hudson) on my Internet Gateway machine. This machine is running Windows 7 (64 Bit, legal, user-account) and connected to the Internet via cable modem (it's not a router). The Windows machine is sharing its Internet Connection via ICS and that works fine on all connected computers. I can access the services via the gateway's public IP (95.x.x.x) on the given ports if they are running on the gateway machine itself. I've added the ports and destination IP address (192.168.0.18) in the Internet network adapter's Advanced Settings dialog (Sharing tab). That's the same dialog where you have a list of preconfigured services like HTTP, FTP and other incoming services. When I do that I can't connect to the services anymore. For some reason port forwarding isn't working. I have uninstalled Bitdefender because I wanted to check if the Firewall interferes. I've also disabled the Windows Firewall and Defender to no avail. I tried a freeware tool that helps to setup port forwarding but that didn't work either. The target machine is a Mac OS X computer whose Firewall is disabled. The IP is static. I can successfully connect to the services using the local IP address (192.168.0.18) from two different machines, including the gateway computer. So internally and externally it seems to me that the ports are open and not blocked, and the issue is with port forwarding itself. From what I understand it should be enough to add an entry to the Advanced Settings dialog to enable port forwarding when there are no firewalls interfering. How can I troubleshoot why port forwarding isn't working for me? What steps should I follow to alleviate the issue? PS: I gladly accept command line solutions. Other things I've tried: adding an Inbound Rule to Windows Firewall for the 1666, 8081 ports trying with Windows Firewall enabled and disabled disabling/enabling the network adapter double-checked that the IP addresses are correct mapping a different incoming port to the service's actual port followed or checked the misc tips in this article What I haven't dared trying yet (let me know if it's worth a shot): disable/enable ICS remove all network adapters (via Control Panel), then re-install and re-configure them

    Read the article

  • Postfix $smtpd_banner rules

    - by horen
    For monitoring purposes I would like to add the IP address to the Postfix smtpd_banner: smtpd_banner = $myhostname ESMTP $smtp_bind_address which works and outputs: 220 mail.mydomain.com ESMTP 123.456.789.0 Now I am wondering if there are any (negative) repercussions to expect. I couldn't find anything about it in the RFC docs. The Postfix docs add another parameter ($mail_name) in their example, so I think I am fine. I just want to verify that my syntax is correct and is allowed.

    Read the article

  • Multiple computers in SBS domain that need a Remote Desktop Connection with a sub domain

    - by Mark
    Hi all, I've been searching the internet for a while for this answer. I have a bunch of computers that are part of a small business server domain and would like to be able to connect to each one individually with remote desktop connection using a subdomain, like: computer1.mydomain.org computer2.mydomain.org etc... I can currently connect to the server easily using an A record with the subdomain pointing to the static IP address with home.mydomain.org, so computer1.home.mydomain.org would also be cool. Thanks!

    Read the article

  • Hard drive restore on reboot on windows embedded

    - by sav
    My company has an old out of service device with windows embedded on it that we want to re purpose. Any changes to the drive (SD Card with 2 partitions), (ie: installed software, ip address, system settings, files) are reset/deleted when we reboot the device. We can successfully make changes to the drive by plugging it into a PC, but that has its limitations and we would like to be able to use our device. Can anyone tell us more about the technology used for doing this and how/if we can disable it?

    Read the article

  • Browser http port-forwarding

    - by Kakao
    When using a browser like Firefox I need that any url of the domain example.com to have appended the port :8008. Not only when I type it at address bar but any where it is referenced within the served html page. All the other domains should be left as is. I know I can setup a proxy like Squid or use a pac file in a web site but I want it simpler if possible.

    Read the article

  • Per Sender Traffic Limit on Cisco 6500

    - by user71557
    Hi All, I have a 6509 with ~1000 user machines in different vlans, I want to allow 10 server machines to send as much as they can/want but to limit all client machines from all subnets to have a sedning rate limit of 1mbps with no receiving limitation. It is worth noting that all my ip addresses are assigned using a DCHP server and there are 1000 of them so I can not write ACLs for every address seperately. Can any one provide some kind of help please?

    Read the article

  • how can I monitor my FTP server [closed]

    - by hanem
    I have installed the FTP server in my PC and I have connected with Filezella client,but when I try to monitor the FTP server fonctionality by taping the snmpwalk command ,I don't have any result concerning the disk space of the server or the memory size,have any one an idea how can I monitor the FTP server and thanks the OS is windows7 and the SNMP is configured,I want to use the commandes of the net-SNMP library,but when I tape: snmpwalk -v1 -c public address of the FTP server I got the same informations as my system

    Read the article

  • Make a temp network.

    - by giodamelio
    I have a XAMPP test server running on my Windows Vista laptop. I also have a small wireless router. I would like be able to create a small temp network that could broadcast that network so any other computers connected to the wifi can go to localhost/ or an internal ip address and view my server. The router will not be able to be connected to the internet, but I don't see how that would make a difference Thanks giodamelio

    Read the article

  • .htaccess help required for appache server

    - by mathew
    I searching for a redirection code for my url: what I want is when some one search in my site it should redirect example: if some one search google.com on mysite then in address line it should look like www.mydomain.com/google.com can be in $_POST method or $_GET how do I do that??

    Read the article

  • URL not responding on OS X, fine on other machine

    - by Rory Fitzpatrick
    For some reason I can't access anything on python.org. nslookup resolves the IP address, but no browser or curl command will fetch anything. It works fine on a VMWare Ubuntu virtual machine and on a Windows machine on the same network. I've checked there's nothing funny in /etc/hosts I don't know where else to go looking for issues, can anyone suggest anything? Running OS X 10.5 Leopard

    Read the article

  • Number of subnets for specific mask

    - by kutacz
    Question source Problem: Your company has been assigned the following IP address: 192.112.136.0 /27 Your group has been assigned the fourth subnet. Question 5: How many useable subnets are available for assignment? Why the answer is 6? I would shoot it's 8 , because 255/32 = 8. More generally - what is an correct algorithm to compute the number of available subnetworks for the same mask?

    Read the article

  • Is it okay to resend to hard bounced emails after X days. What is X?

    - by V. Hsu
    If I see an email returned due to a hard bounce, after how many days is it acceptable to resend to that email address. It is possible for emails to be reactivated or for temporary outages, so it doesn't make sense to keep an email in my hard bounce email list forever. I've already seen cases where I receive emails from addresses that were put in my hard bounce email list months ago. Any recommendations? Are there specific recommendations from ISPs?

    Read the article

  • Windows 2003 routing by port

    - by vansickle
    I have remote Windows 2003 server with two network interfaces e.g. Cn1 and Cn2. I need that all traffic goes through Cn1 except for one port (for me it's 3389, rdp for administration) that works over Cn2. Currently when I setup all connections work through Cn1, I completely lose connection over Cn2 - and can't connect to server via RDP over Cn2. Now I used static routing based on my ip address (which can changed - so it's bad).

    Read the article

< Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >