Search Results

Search found 7211 results on 289 pages for 'enable if'.

Page 41/289 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

  • How can I forward ALL traffic over a site-to-site VPN on Cisco ASA?

    - by Scott Clements
    Hi There, I currently have two Cisco ASA 5100 routers. They are at different physical sites and are configured with a site-to-site VPN which is active and working. I can communicate with the subnets on either site from the other and both are connected to the internet, however I need to ensure that all the traffic at my remote site goes through this VPN to my site here. I know that the web traffic is doing so as a "tracert" confirms this, but I need to ensure that all other network traffic is being directed over this VPN to my network here. Here is my config for the ASA router at my remote site: hostname ciscoasa domain-name xxxxx enable password 78rl4MkMED8xiJ3g encrypted names ! interface Ethernet0/0 nameif NIACEDC security-level 100 ip address x.x.x.x 255.255.255.0 ! interface Ethernet0/1 description External Janet Connection nameif JANET security-level 0 ip address x.x.x.x 255.255.255.248 ! interface Ethernet0/2 shutdown no nameif security-level 100 no ip address ! interface Ethernet0/3 shutdown no nameif security-level 100 ip address dhcp setroute ! interface Management0/0 nameif management security-level 100 ip address 192.168.100.1 255.255.255.0 management-only ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup NIACEDC dns server-group DefaultDNS name-server 154.32.105.18 name-server 154.32.107.18 domain-name XXXX same-security-traffic permit inter-interface same-security-traffic permit intra-interface access-list ren_access_in extended permit ip any any access-list ren_access_in extended permit tcp any any access-list ren_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_nat0_outbound extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list JANET_20_cryptomap extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_access_in extended permit ip any any access-list NIACEDC_access_in extended permit tcp any any access-list JANET_access_out extended permit ip any any access-list NIACEDC_access_out extended permit ip any any pager lines 24 logging enable logging asdm informational mtu NIACEDC 1500 mtu JANET 1500 mtu management 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-522.bin no asdm history enable arp timeout 14400 nat-control global (NIACEDC) 1 interface global (JANET) 1 interface nat (NIACEDC) 0 access-list NIACEDC_nat0_outbound nat (NIACEDC) 1 192.168.12.0 255.255.255.0 access-group NIACEDC_access_in in interface NIACEDC access-group NIACEDC_access_out out interface NIACEDC access-group JANET_access_out out interface JANET route JANET 0.0.0.0 0.0.0.0 194.82.121.82 1 route JANET 0.0.0.0 0.0.0.0 192.168.3.248 tunneled timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute http server enable http 192.168.12.0 255.255.255.0 NIACEDC http 192.168.100.0 255.255.255.0 management http 192.168.9.0 255.255.255.0 NIACEDC no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto map JANET_map 20 match address JANET_20_cryptomap crypto map JANET_map 20 set pfs crypto map JANET_map 20 set peer X.X.X.X crypto map JANET_map 20 set transform-set ESP-AES-256-SHA crypto map JANET_map interface JANET crypto isakmp enable JANET crypto isakmp policy 10 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 50 authentication pre-share encryption aes-256 hash sha group 5 lifetime 86400 tunnel-group X.X.X.X type ipsec-l2l tunnel-group X.X.X.X ipsec-attributes pre-shared-key * telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd address 192.168.100.2-192.168.100.254 management dhcpd enable management ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect http ! service-policy global_policy global prompt hostname context no asdm history enable Thanks in advance, Scott

    Read the article

  • FFMPEG Segfault Solutions

    - by Brentley_11
    I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

    Read the article

  • FFMPEG Segfault Solutions

    - by Brentley_11
    I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

    Read the article

  • Compiling ruby1.9.1 hangs and fills swap!

    - by nfm
    I'm compiling Ruby 1.9.1-p376 under Ubuntu 8.04 server LTS (64-bit), by doing the following: $ ./configure $ make $ sudo make install ./configure works without complaints. make hangs indefinitely until all my RAM and swap is gone. It get stuck after the following output: compiling ripper make[1]: Entering directory `/tmp/ruby1.9.1/ruby-1.9.1-p376/ext/ripper' gcc -I. -I../../.ext/include/x86_64-linux -I../.././include -I../.././ext/ripper -I../.. -I../../. -DRUBY_EXTCONF_H=\"extconf.h\" -fPIC -O2 -g -Wall -Wno-parentheses -o ripper.o -c ripper.c If I run the gcc command by hand, with the -v argument to get verbose output, it hangs after the following: Using built-in specs. Target: x86_64-linux-gnu Configured with: ../src/configure -v --enable-languages=c,c++,fortran,objc,obj-c++,treelang --prefix=/usr --enable-shared --with-system-zlib --libexecdir=/usr/lib --without-included-gettext --enable-threads=posix --enable-nls --with-gxx-include-dir=/usr/include/c++/4.2 --program-suffix=-4.2 --enable-clocale=gnu --enable-libstdcxx-debug --enable-objc-gc --enable-mpfr --enable-checking=release --build=x86_64-linux-gnu --host=x86_64-linux-gnu --target=x86_64-linux-gnu Thread model: posix gcc version 4.2.4 (Ubuntu 4.2.4-1ubuntu4) /usr/lib/gcc/x86_64-linux-gnu/4.2.4/cc1 -quiet -v -I. -I../../.ext/include/x86_64-linux -I../.././include -I../.././ext/ripper -I../.. -I../../. -DRUBY_EXTCONF_H="extconf.h" ripper.c -quiet -dumpbase ripper.c -mtune=generic -auxbase-strip ripper.o -g -O2 -Wall -Wno-parentheses -version -fPIC -fstack-protector -fstack-protector -o /tmp/ccRzHvYH.s ignoring nonexistent directory "/usr/local/include/x86_64-linux-gnu" ignoring nonexistent directory "/usr/lib/gcc/x86_64-linux-gnu/4.2.4/../../../../x86_64-linux-gnu/include" ignoring nonexistent directory "/usr/include/x86_64-linux-gnu" ignoring duplicate directory "../.././ext/ripper" ignoring duplicate directory "../../." #include "..." search starts here: #include <...> search starts here: . ../../.ext/include/x86_64-linux ../.././include ../.. /usr/local/include /usr/lib/gcc/x86_64-linux-gnu/4.2.4/include /usr/include End of search list. GNU C version 4.2.4 (Ubuntu 4.2.4-1ubuntu4) (x86_64-linux-gnu) compiled by GNU C version 4.2.4 (Ubuntu 4.2.4-1ubuntu4). GGC heuristics: --param ggc-min-expand=47 --param ggc-min-heapsize=32795 Compiler executable checksum: 6e11fa7ca85fc28646173a91f2be2ea3 I just compiled ruby on another computer for reference, and it took about 10 seconds to print the following output (after the above Compiler executable checksum line): COLLECT_GCC_OPTIONS='-v' '-I.' '-I../../.ext/include/i686-linux' '-I../.././include' '-I../.././ext/ripper' '-I../..' '-I../../.' '-DRUBY_EXTCONF_H="extconf.h"' '-D_FILE_OFFSET_BITS=64' '-fPIC' '-O2' '-g' '-Wall' '-Wno-parentheses' '-o' 'ripper.o' '-c' '-mtune=generic' '-march=i486' as -V -Qy -o ripper.o /tmp/cca4fa7R.s GNU assembler version 2.20 (i486-linux-gnu) using BFD version (GNU Binutils for Ubuntu) 2.20 COMPILER_PATH=/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/ LIBRARY_PATH=/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/4.4.1/../../../../lib/:/lib/../lib/:/usr/lib/../lib/:/usr/lib/gcc/i486-linux-gnu/4.4.1/../../../:/lib/:/usr/lib/ COLLECT_GCC_OPTIONS='-v' '-I.' '-I../../.ext/include/i686-linux' '-I../.././include' '-I../.././ext/ripper' '-I../..' '-I../../.' '-DRUBY_EXTCONF_H="extconf.h"' '-D_FILE_OFFSET_BITS=64' '-fPIC' '-O2' '-g' '-Wall' '-Wno-parentheses' '-o' 'ripper.o' '-c' '-mtune=generic' '-march=i486' I have absolutely no clue what could be going wrong here - any ideas where I should start?

    Read the article

  • Installing vim7.2 on Solaris Sparc 10 as non-root

    - by Tobbe
    I'm trying to install vim to $HOME/bin by compiling the sources. ./configure --prefix=$home/bin seems to work, but when running make I get: > make Starting make in the src directory. If there are problems, cd to the src directory and run make there cd src && make first gcc -c -I. -Iproto -DHAVE_CONFIG_H -DFEAT_GUI_GTK -I/usr/include/gtk-2.0 -I/usr/lib/gtk-2.0/include -I/usr/include/atk-1.0 -I/usr/include/pango-1.0 -I/usr/openwin/include -I/usr/sfw/include -I/usr/sfw/include/freetype2 -I/usr/include/glib-2.0 -I/usr/lib/glib-2.0/include -g -O2 -I/usr/openwin/include -o objects/buffer.o buffer.c In file included from buffer.c:28: vim.h:41: error: syntax error before ':' token In file included from os_unix.h:29, from vim.h:245, from buffer.c:28: /usr/include/sys/stat.h:251: error: syntax error before "blksize_t" /usr/include/sys/stat.h:255: error: syntax error before '}' token /usr/include/sys/stat.h:309: error: syntax error before "blksize_t" /usr/include/sys/stat.h:310: error: conflicting types for 'st_blocks' /usr/include/sys/stat.h:252: error: previous declaration of 'st_blocks' was here /usr/include/sys/stat.h:313: error: syntax error before '}' token In file included from /opt/local/bin/../lib/gcc/sparc-sun-solaris2.6/3.4.6/include/sys/signal.h:132, from /usr/include/signal.h:26, from os_unix.h:163, from vim.h:245, from buffer.c:28: /usr/include/sys/siginfo.h:259: error: syntax error before "ctid_t" /usr/include/sys/siginfo.h:292: error: syntax error before '}' token /usr/include/sys/siginfo.h:294: error: syntax error before '}' token /usr/include/sys/siginfo.h:390: error: syntax error before "ctid_t" /usr/include/sys/siginfo.h:398: error: conflicting types for '__fault' /usr/include/sys/siginfo.h:267: error: previous declaration of '__fault' was here /usr/include/sys/siginfo.h:404: error: conflicting types for '__file' /usr/include/sys/siginfo.h:273: error: previous declaration of '__file' was here /usr/include/sys/siginfo.h:420: error: conflicting types for '__prof' /usr/include/sys/siginfo.h:287: error: previous declaration of '__prof' was here /usr/include/sys/siginfo.h:424: error: conflicting types for '__rctl' /usr/include/sys/siginfo.h:291: error: previous declaration of '__rctl' was here /usr/include/sys/siginfo.h:426: error: syntax error before '}' token /usr/include/sys/siginfo.h:428: error: syntax error before '}' token /usr/include/sys/siginfo.h:432: error: syntax error before "k_siginfo_t" /usr/include/sys/siginfo.h:437: error: syntax error before '}' token In file included from /usr/include/signal.h:26, from os_unix.h:163, from vim.h:245, from buffer.c:28: /opt/local/bin/../lib/gcc/sparc-sun-solaris2.6/3.4.6/include/sys/signal.h:173: error: syntax error before "siginfo_t" In file included from os_unix.h:163, from vim.h:245, from buffer.c:28: /usr/include/signal.h:111: error: syntax error before "siginfo_t" /usr/include/signal.h:113: error: syntax error before "siginfo_t" buffer.c: In function `buflist_new': buffer.c:1502: error: storage size of 'st' isn't known buffer.c: In function `buflist_findname': buffer.c:1989: error: storage size of 'st' isn't known buffer.c: In function `setfname': buffer.c:2578: error: storage size of 'st' isn't known buffer.c: In function `otherfile_buf': buffer.c:2836: error: storage size of 'st' isn't known buffer.c: In function `buf_setino': buffer.c:2874: error: storage size of 'st' isn't known buffer.c: In function `buf_same_ino': buffer.c:2894: error: dereferencing pointer to incomplete type buffer.c:2895: error: dereferencing pointer to incomplete type *** Error code 1 make: Fatal error: Command failed for target `objects/buffer.o' Current working directory /home/xluntor/vim72/src *** Error code 1 make: Fatal error: Command failed for target `first' How do I fix the make errors? Or is there another way to install vim as non-root? Thanks in advance EDIT: I took a look at the google groups link Sarah posted. The "Compiling Vim" page linked from there was for Linux, so the commands doesn't even work on Solars. But it did hint at logging the output of ./configure to a file, so I did that. Here it is: ./configure output removed. New version further down. Does anyone spot anything critical missing? EDIT 2: So I downloaded the vim package from sunfreeware. I couldn't just install it, since I don't have root privileges, but I was able to extract the package file. This was the file structure in it: `-- SMCvim `-- reloc |-- bin |-- doc | `-- vim `-- share |-- man | `-- man1 `-- vim `-- vim72 |-- autoload | `-- xml |-- colors |-- compiler |-- doc |-- ftplugin |-- indent |-- keymap |-- lang |-- macros | |-- hanoi | |-- life | |-- maze | `-- urm |-- plugin |-- print |-- spell |-- syntax |-- tools `-- tutor I moved the three files (vim, vimtutor, xdd) in SMCvim/reloc/bin to $HOME/bin, so now I can finally run $HOME/bin/vim! But where do I put the "share" directory and its content? EDIT 3: It might also be worth noting that there already exists an install of vim on the system, but it is broken. When I try to run it I get: ld.so.1: vim: fatal: libgtk-1.2.so.0: open failed: No such file or directory "which vim" outputs /opt/local/bin/vim EDIT 4: Trying to compile this on Solaris 10. uname -a SunOS ws005-22 5.10 Generic_141414-10 sun4u sparc SUNW,SPARC-Enterprise New ./configure output: ./configure --prefix=$home/bin ac_cv_sizeof_int=8 --enable-rubyinterp configure: loading cache auto/config.cache checking whether make sets $(MAKE)... yes checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... unsupported checking how to run the C preprocessor... gcc -E checking for grep that handles long lines and -e... /usr/sfw/bin/ggrep checking for egrep... /usr/sfw/bin/ggrep -E checking for library containing strerror... none required checking for gawk... gawk checking for strip... strip checking for ANSI C header files... yes checking for sys/wait.h that is POSIX.1 compatible... no configure: checking for buggy tools... checking for BeOS... no checking for QNX... no checking for Darwin (Mac OS X)... no checking --with-local-dir argument... Defaulting to /usr/local checking --with-vim-name argument... Defaulting to vim checking --with-ex-name argument... Defaulting to ex checking --with-view-name argument... Defaulting to view checking --with-global-runtime argument... no checking --with-modified-by argument... no checking if character set is EBCDIC... no checking --disable-selinux argument... no checking for is_selinux_enabled in -lselinux... no checking --with-features argument... Defaulting to normal checking --with-compiledby argument... no checking --disable-xsmp argument... no checking --disable-xsmp-interact argument... no checking --enable-mzschemeinterp argument... no checking --enable-perlinterp argument... no checking --enable-pythoninterp argument... no checking --enable-tclinterp argument... no checking --enable-rubyinterp argument... yes checking for ruby... /opt/sfw/bin/ruby checking Ruby version... OK checking Ruby header files... /opt/sfw/lib/ruby/1.6/sparc-solaris2.10 checking --enable-cscope argument... no checking --enable-workshop argument... no checking --disable-netbeans argument... no checking for socket in -lsocket... yes checking for gethostbyname in -lnsl... yes checking whether compiling netbeans integration is possible... no checking --enable-sniff argument... no checking --enable-multibyte argument... no checking --enable-hangulinput argument... no checking --enable-xim argument... defaulting to auto checking --enable-fontset argument... no checking for xmkmf... /usr/openwin/bin/xmkmf checking for X... libraries /usr/openwin/lib, headers /usr/openwin/include checking whether -R must be followed by a space... no checking for gethostbyname... yes checking for connect... yes checking for remove... yes checking for shmat... yes checking for IceConnectionNumber in -lICE... yes checking if X11 header files can be found... yes checking for _XdmcpAuthDoIt in -lXdmcp... no checking for IceOpenConnection in -lICE... yes checking for XpmCreatePixmapFromData in -lXpm... yes checking if X11 header files implicitly declare return values... no checking --enable-gui argument... yes/auto - automatic GUI support checking whether or not to look for GTK... yes checking whether or not to look for GTK+ 2... yes checking whether or not to look for GNOME... no checking whether or not to look for Motif... yes checking whether or not to look for Athena... yes checking whether or not to look for neXtaw... yes checking whether or not to look for Carbon... yes checking --with-gtk-prefix argument... no checking --with-gtk-exec-prefix argument... no checking --disable-gtktest argument... gtk test enabled checking for gtk-config... /opt/local/bin/gtk-config checking for pkg-config... /usr/bin/pkg-config checking for GTK - version = 2.2.0... yes; found version 2.4.9 checking X11/SM/SMlib.h usability... yes checking X11/SM/SMlib.h presence... yes checking for X11/SM/SMlib.h... yes checking X11/xpm.h usability... yes checking X11/xpm.h presence... yes checking for X11/xpm.h... yes checking X11/Sunkeysym.h usability... yes checking X11/Sunkeysym.h presence... yes checking for X11/Sunkeysym.h... yes checking for XIMText in X11/Xlib.h... yes X GUI selected; xim has been enabled checking whether toupper is broken... no checking whether __DATE__ and __TIME__ work... yes checking elf.h usability... yes checking elf.h presence... yes checking for elf.h... yes checking for main in -lelf... yes checking for dirent.h that defines DIR... yes checking for library containing opendir... none required checking for sys/wait.h that defines union wait... no checking stdarg.h usability... yes checking stdarg.h presence... yes checking for stdarg.h... yes checking stdlib.h usability... yes checking stdlib.h presence... yes checking for stdlib.h... yes checking string.h usability... yes checking string.h presence... yes checking for string.h... yes checking sys/select.h usability... yes checking sys/select.h presence... yes checking for sys/select.h... yes checking sys/utsname.h usability... yes checking sys/utsname.h presence... yes checking for sys/utsname.h... yes checking termcap.h usability... yes checking termcap.h presence... yes checking for termcap.h... yes checking fcntl.h usability... yes checking fcntl.h presence... yes checking for fcntl.h... yes checking sgtty.h usability... yes checking sgtty.h presence... yes checking for sgtty.h... yes checking sys/ioctl.h usability... yes checking sys/ioctl.h presence... yes checking for sys/ioctl.h... yes checking sys/time.h usability... yes checking sys/time.h presence... yes checking for sys/time.h... yes checking sys/types.h usability... yes checking sys/types.h presence... yes checking for sys/types.h... yes checking termio.h usability... yes checking termio.h presence... yes checking for termio.h... yes checking iconv.h usability... yes checking iconv.h presence... yes checking for iconv.h... yes checking langinfo.h usability... yes checking langinfo.h presence... yes checking for langinfo.h... yes checking math.h usability... yes checking math.h presence... yes checking for math.h... yes checking unistd.h usability... yes checking unistd.h presence... yes checking for unistd.h... yes checking stropts.h usability... no checking stropts.h presence... yes configure: WARNING: stropts.h: present but cannot be compiled configure: WARNING: stropts.h: check for missing prerequisite headers? configure: WARNING: stropts.h: see the Autoconf documentation configure: WARNING: stropts.h: section "Present But Cannot Be Compiled" configure: WARNING: stropts.h: proceeding with the preprocessor's result configure: WARNING: stropts.h: in the future, the compiler will take precedence checking for stropts.h... yes checking errno.h usability... yes checking errno.h presence... yes checking for errno.h... yes checking sys/resource.h usability... yes checking sys/resource.h presence... yes checking for sys/resource.h... yes checking sys/systeminfo.h usability... yes checking sys/systeminfo.h presence... yes checking for sys/systeminfo.h... yes checking locale.h usability... yes checking locale.h presence... yes checking for locale.h... yes checking sys/stream.h usability... no checking sys/stream.h presence... yes configure: WARNING: sys/stream.h: present but cannot be compiled configure: WARNING: sys/stream.h: check for missing prerequisite headers? configure: WARNING: sys/stream.h: see the Autoconf documentation configure: WARNING: sys/stream.h: section "Present But Cannot Be Compiled" configure: WARNING: sys/stream.h: proceeding with the preprocessor's result configure: WARNING: sys/stream.h: in the future, the compiler will take precedence checking for sys/stream.h... yes checking termios.h usability... yes checking termios.h presence... yes checking for termios.h... yes checking libc.h usability... no checking libc.h presence... no checking for libc.h... no checking sys/statfs.h usability... yes checking sys/statfs.h presence... yes checking for sys/statfs.h... yes checking poll.h usability... yes checking poll.h presence... yes checking for poll.h... yes checking sys/poll.h usability... yes checking sys/poll.h presence... yes checking for sys/poll.h... yes checking pwd.h usability... yes checking pwd.h presence... yes checking for pwd.h... yes checking utime.h usability... yes checking utime.h presence... yes checking for utime.h... yes checking sys/param.h usability... yes checking sys/param.h presence... yes checking for sys/param.h... yes checking libintl.h usability... yes checking libintl.h presence... yes checking for libintl.h... yes checking libgen.h usability... yes checking libgen.h presence... yes checking for libgen.h... yes checking util/debug.h usability... no checking util/debug.h presence... no checking for util/debug.h... no checking util/msg18n.h usability... no checking util/msg18n.h presence... no checking for util/msg18n.h... no checking frame.h usability... no checking frame.h presence... no checking for frame.h... no checking sys/acl.h usability... yes checking sys/acl.h presence... yes checking for sys/acl.h... yes checking sys/access.h usability... no checking sys/access.h presence... no checking for sys/access.h... no checking sys/sysctl.h usability... no checking sys/sysctl.h presence... no checking for sys/sysctl.h... no checking sys/sysinfo.h usability... yes checking sys/sysinfo.h presence... yes checking for sys/sysinfo.h... yes checking wchar.h usability... yes checking wchar.h presence... yes checking for wchar.h... yes checking wctype.h usability... yes checking wctype.h presence... yes checking for wctype.h... yes checking for sys/ptem.h... no checking for pthread_np.h... no checking strings.h usability... yes checking strings.h presence... yes checking for strings.h... yes checking if strings.h can be included after string.h... yes checking whether gcc needs -traditional... no checking for an ANSI C-conforming const... yes checking for mode_t... yes checking for off_t... yes checking for pid_t... yes checking for size_t... yes checking for uid_t in sys/types.h... yes checking whether time.h and sys/time.h may both be included... yes checking for ino_t... yes checking for dev_t... yes checking for rlim_t... yes checking for stack_t... yes checking whether stack_t has an ss_base field... no checking --with-tlib argument... empty: automatic terminal library selection checking for tgetent in -lncurses... yes checking whether we talk terminfo... yes checking what tgetent() returns for an unknown terminal... zero checking whether termcap.h contains ospeed... yes checking whether termcap.h contains UP, BC and PC... yes checking whether tputs() uses outfuntype... no checking whether sys/select.h and sys/time.h may both be included... yes checking for /dev/ptc... no checking for SVR4 ptys... yes checking for ptyranges... don't know checking default tty permissions/group... can't determine - assume ptys are world accessable world checking return type of signal handlers... void checking for struct sigcontext... no checking getcwd implementation is broken... no checking for bcmp... yes checking for fchdir... yes checking for fchown... yes checking for fseeko... yes checking for fsync... yes checking for ftello... yes checking for getcwd... yes checking for getpseudotty... no checking for getpwnam... yes checking for getpwuid... yes checking for getrlimit... yes checking for gettimeofday... yes checking for getwd... yes checking for lstat... yes checking for memcmp... yes checking for memset... yes checking for nanosleep... no checking for opendir... yes checking for putenv... yes checking for qsort... yes checking for readlink... yes checking for select... yes checking for setenv... yes checking for setpgid... yes checking for setsid... yes checking for sigaltstack... yes checking for sigstack... yes checking for sigset... yes checking for sigsetjmp... yes checking for sigaction... yes checking for sigvec... no checking for strcasecmp... yes checking for strerror... yes checking for strftime... yes checking for stricmp... no checking for strncasecmp... yes checking for strnicmp... no checking for strpbrk... yes checking for strtol... yes checking for tgetent... yes checking for towlower... yes checking for towupper... yes checking for iswupper... yes checking for usleep... yes checking for utime... yes checking for utimes... yes checking for st_blksize... no checking whether stat() ignores a trailing slash... no checking for iconv_open()... yes; with -liconv checking for nl_langinfo(CODESET)... yes checking for strtod in -lm... yes checking for strtod() and other floating point functions... yes checking --disable-acl argument... no checking for acl_get_file in -lposix1e... no checking for acl_get_file in -lacl... no checking for POSIX ACL support... no checking for Solaris ACL support... yes checking for AIX ACL support... no checking --disable-gpm argument... no checking for gpm... no checking --disable-sysmouse argument... no checking for sysmouse... no checking for rename... yes checking for sysctl... not usable checking for sysinfo... not usable checking for sysinfo.mem_unit... no checking for sysconf... yes checking size of int... (cached) 8 checking whether memmove handles overlaps... yes checking for _xpg4_setrunelocale in -lxpg4... no checking how to create tags... ctags -t checking how to run man with a section nr... man -s checking --disable-nls argument... no checking for msgfmt... msgfmt checking for NLS... no "po/Makefile" - disabled checking dlfcn.h usability... yes checking dlfcn.h presence... yes checking for dlfcn.h... yes checking for dlopen()... yes checking for dlsym()... yes checking setjmp.h usability... yes checking setjmp.h presence... yes checking for setjmp.h... yes checking for GCC 3 or later... yes configure: updating cache auto/config.cache configure: creating auto/config.status config.status: creating auto/config.mk config.status: creating auto/config.h Make: make Starting make in the src directory. If there are problems, cd to the src directory and run make there cd src && make first mkdir objects CC="gcc -Iproto -DHAVE_CONFIG_H -DFEAT_GUI_GTK -I/usr/include/gtk-2.0 -I/usr/lib/gtk-2.0/include -I/usr/include/atk-1.0 -I/usr/include/pango-1.0 -I/usr/openwin/include -I/usr/sfw/include -I/usr/sfw/include/freetype2 -I/usr/include/glib-2.0 -I/usr/lib/glib-2.0/include -I/usr/openwin/include -I/opt/sfw/lib/ruby/1.6/sparc-solaris2.10 " srcdir=. sh ./osdef.sh gcc -c -I. -Iproto -DHAVE_CONFIG_H -DFEAT_GUI_GTK -I/usr/include/gtk-2.0 -I/usr/lib/gtk-2.0/include -I/usr/include/atk-1.0 -I/usr/include/pango-1.0 -I/usr/openwin/include -I/usr/sfw/include -I/usr/sfw/include/freetype2 -I/usr/include/glib-2.0 -I/usr/lib/glib-2.0/include -g -O2 -I/usr/openwin/include -I/opt/sfw/lib/ruby/1.6/sparc-solaris2.10 -o objects/buffer.o buffer.c In file included from os_unix.h:29, from vim.h:245, from buffer.c:28: /usr/include/sys/stat.h:251: error: syntax error before "blksize_t" /usr/include/sys/stat.h:255: error: syntax error before '}' token /usr/include/sys/stat.h:309: error: syntax error before "blksize_t" /usr/include/sys/stat.h:310: error: conflicting types for 'st_blocks' /usr/include/sys/stat.h:252: error: previous declaration of 'st_blocks' was here /usr/include/sys/stat.h:313: error: syntax error before '}' token In file included from /opt/local/bin/../lib/gcc/sparc-sun-solaris2.6/3.4.6/include/sys/signal.h:132, from /usr/include/signal.h:26, from os_unix.h:163, from vim.h:245, from buffer.c:28: /usr/include/sys/siginfo.h:259: error: syntax error before "ctid_t" /usr/include/sys/siginfo.h:292: error: syntax error before '}' token /usr/include/sys/siginfo.h:294: error: syntax error before '}' token /usr/include/sys/siginfo.h:390: error: syntax error before "ctid_t" /usr/include/sys/siginfo.h:398: error: conflicting types for '__fault' /usr/include/sys/siginfo.h:267: error: previous declaration of '__fault' was here /usr/include/sys/siginfo.h:404: error: conflicting types for '__file' /usr/include/sys/siginfo.h:273: error: previous declaration of '__file' was here /usr/include/sys/siginfo.h:420: error: conflicting types for '__prof' /usr/include/sys/siginfo.h:287: error: previous declaration of '__prof' was here /usr/include/sys/siginfo.h:424: error: conflicting types for '__rctl' /usr/include/sys/siginfo.h:291: error: previous declaration of '__rctl' was here /usr/include/sys/siginfo.h:426: error: syntax error before '}' token /usr/include/sys/siginfo.h:428: error: syntax error before '}' token /usr/include/sys/siginfo.h:432: error: syntax error before "k_siginfo_t" /usr/include/sys/siginfo.h:437: error: syntax error before '}' token In file included from /usr/include/signal.h:26, from os_unix.h:163, from vim.h:245, from buffer.c:28: /opt/local/bin/../lib/gcc/sparc-sun-solaris2.6/3.4.6/include/sys/signal.h:173: error: syntax error before "siginfo_t" In file included from os_unix.h:163, from vim.h:245, from buffer.c:28: /usr/include/signal.h:111: error: syntax error before "siginfo_t" /usr/include/signal.h:113: error: syntax error before "siginfo_t" buffer.c: In function `buflist_new': buffer.c:1502: error: storage size of 'st' isn't known buffer.c: In function `buflist_findname': buffer.c:1989: error: storage size of 'st' isn't known buffer.c: In function `setfname': buffer.c:2578: error: storage size of 'st' isn't known buffer.c: In function `otherfile_buf': buffer.c:2836: error: storage size of 'st' isn't known buffer.c: In function `buf_setino': buffer.c:2874: error: storage size of 'st' isn't known buffer.c: In function `buf_same_ino': buffer.c:2894: error: dereferencing pointer to incomplete type buffer.c:2895: error: dereferencing pointer to incomplete type *** Error code 1 make: Fatal error: Command failed for target `objects/buffer.o' Current working directory /home/xluntor/vim72/src *** Error code 1 make: Fatal error: Command failed for target `first'

    Read the article

  • No more internet connection after update in 14.04 with Intel Dual Band Wireless AC 7260

    - by luis
    My Dell XPS 15 (haswell) was working fine until I stupidly accepted recently to apply Ubuntu updates. Since then, my wifi does not work (it shows "device not managed" when clicking wifi icon in toolbar). Even USB to Ethernet adapter does not seem to work. Bluetooth at least "sees" other bluetooth devices around... See below output from dmesg (dmesg |grep iwl) : [ 886.462459] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 886.462561] iwlwifi 0000:06:00.0: Direct firmware load failed with error -2 [ 886.462562] iwlwifi 0000:06:00.0: Falling back to user helper [ 886.463284] iwlwifi 0000:06:00.0: loaded firmware version 22.1.7.0 op_mode iwlmvm [ 886.475345] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 886.475433] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.475684] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.689214] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Below the output from modinfo iwlwifi: filename: /lib/modules/3.13.0-29- generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko license: GPL author: Copyright(c) 2003-2013 Intel Corporation <[email protected]> version: in-tree: description: Intel(R) Wireless WiFi driver for Linux firmware: iwlwifi-100-5.ucode firmware: iwlwifi-1000-5.ucode firmware: iwlwifi-135-6.ucode firmware: iwlwifi-105-6.ucode firmware: iwlwifi-2030-6.ucode firmware: iwlwifi-2000-6.ucode firmware: iwlwifi-5150-2.ucode firmware: iwlwifi-5000-5.ucode firmware: iwlwifi-6000g2b-6.ucode firmware: iwlwifi-6000g2a-5.ucode firmware: iwlwifi-6050-5.ucode firmware: iwlwifi-6000-4.ucode firmware: iwlwifi-3160-7.ucode firmware: iwlwifi-7260-7.ucode srcversion: 1E6912E109D5A43B310FB34 alias: pci:v00008086d0000095Asv*sd00005490bc*sc*i* (a pack of lines of kind "alias: pci:xxxxx...." that I guess are not helpful) alias: pci:v00008086d0000095Bsv*sd00005290bc*sc*i* depends: cfg80211 intree: Y vermagic: 3.13.0-29-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: 66:02:CB:36:F1:31:3B:EA:01:C4:BD:A9:65:67:CF:A7:23:C9:70:D8 sig_hashalgo: sha512 parm: swcrypto:using crypto in software (default 0 [hardware]) (int) parm: 11n_disable:disable 11n functionality, bitmap: 1: full, 2: disable agg TX, 4: disable agg RX, 8 enable agg TX (uint) parm: amsdu_size_8K:enable 8K amsdu size (default 0) (int) parm: fw_restart:restart firmware in case of error (default true) (bool) parm: antenna_coupling:specify antenna coupling in dB (defualt: 0 dB) (int) parm: wd_disable:Disable stuck queue watchdog timer 0=system default, 1=disable, 2=enable (default: 0) (int) parm: nvm_file:NVM file name (charp) parm: bt_coex_active:enable wifi/bt co-exist (default: enable) (bool) parm: led_mode:0=system default, 1=On(RF On)/Off(RF Off), 2=blinking, 3=Off (default: 0) (int) parm: power_save:enable WiFi power management (default: disable) (bool) parm: power_level:default power save level (range from 1 - 5, default: 1) (int) I downloaded the latest versions of iwlwifi firmware from git (git clone git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git; copy iwlwifi-3160-9.ucode iwlwifi-7260-9.ucode iwlwifi-7265-9.ucode to /lib/firmware and reboot) but as you can imagine it did not help. Update #1: Downloaded from http://wireless.kernel.org/en/users/Drivers/iwlwifi?action=AttachFile&do=get&target=iwlwifi-7260-ucode-22.15.8.0.tgz and copied the file into /lib/firmware. After reloading it with modprobe, it seems to be OK: [ 14.761283] iwlwifi 0000:06:00.0: enabling device (0000 -> 0002) [ 14.761472] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 14.772478] iwlwifi 0000:06:00.0: loaded firmware version 22.15.8.0 op_mode iwlmvm [ 14.800274] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 14.800349] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 14.800657] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 15.007048] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' However, clicking in wifi in the toolbar still shows "device not managed". Any clues? Many thanks! Luis

    Read the article

  • Process for Securing Web Sites and Applications

    - by Aamir Hasan
    The following quick-start guide provides a detailed overview of how to configure security for IIS 6.0. Reduce the Attack Surface of the Web Server 1.       Enable only essential Windows Server 2003 components and services. 2.       Enable only essential IIS 6.0 components and services. 3.       Enable only essential Web service extensions. 4.       Enable only essential Multipurpose Internet Mail Extensions (MIME) types. 5.       Configure Windows Server 2003 security settings. Prevent Unauthorized Access to Web Sites and Applications 1.       Store content on a dedicated disk volume. 2.       Set IIS Web site permissions. 3.       Set IP address and domain name restrictions. 4.       Set the NTFS file system permissions. Isolate Web Sites and Applications 1.       Evaluate the effects of impersonation on application compatibility: 2·         Identify the impersonation behavior for ASP applications. 3·         Select the impersonation behavior for ASP.NET applications. 4.       Configure Web sites and applications for isolation. Configure User Authentication 1.       Configure Web site authentication. 2·         Select the Web site authentication method. 3·         Configure the Web site authentication method. 4.       Configure File Transfer Protocol (FTP) site authentication. Encrypt Confidential Data Exchanged with Clients 1.       Use Secure Sockets Layer (SSL) to encrypt confidential data. 2.       Use Internet Protocol security (IPSec) or virtual private network (VPN) with remote administration. Maintain Web Site and Application Security 1.       Obtain and apply current security patches. 2.       Enable Windows Server 2003 security logs. 3.       Enable file access auditing for Web site content. 4.       Configure IIS logs. 5.       Review security policies, processes, and procedures.  Note:To secure the Web sites and applications in a Web farm, use the process described in this chapter to configure security for each server in the Web farm. Link:http://www.studentacad.com/post/2010/04/28/Process-for-Securing-Web-Sites-and-Applications.aspx

    Read the article

  • SVG as CSS background for website navigation-bar

    - by Irfan Mir
    I drew a small (horizontal / in width) svg to be the background of my website's navigation. My website's navigation takes place a 100% of the browser's viewport and I want the svg image to fill that 100% space. So, using css I set the background of the navigation (.nav) to nav.svg but then I saw (whenI opened the html file in a browser) that the svg was not the full-width of the nav, but at the small width I drew it at. How can I get the SVG to stretch and fill the entire width of the navigation (100% of the page) ? Here is the code for the html file where the navigation is in: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html lang="en"><head><meta http-equiv="Content-Type" content="text/html; charset=utf-8"> <title>Distributed Horizontal Menu</title> <meta name="generator" content="PSPad editor, www.pspad.com"> <style type="text/css"> *{ margin:0; padding:0; } .nav { margin:0; padding:0; min-width:42em; width:100%; height:47px; overflow:hidden; background:transparent url(nav.svg) no-repeat; text-align:justify; font:bold 88%/1.1 verdana; } .nav li { display:inline; list-style:none; } .nav li.last { margin-right:100%; } .nav li a { display:inline-block; padding:13px 4px 0; height:31px; color:#fff; vertical-align:middle; text-decoration:none; } .nav li a:hover { color:#ff6; background:#36c; } @media screen and (max-width:322px){ /* styling causing first break will go here*/ /* but in the meantime, a test */ body{ background:#ff0000; } } </style></head><body> <ul class="nav"> <!--[test to comment out random items] <li>&nbsp; <a href="#">netscape&nbsp;9</a></li> [the spacing should be distributed]--> <li>&nbsp; <a href="#">internet&nbsp;explorer&nbsp;6-8</a></li> <li>&nbsp; <a href="#">opera&nbsp;10</a></li> <li>&nbsp; <a href="#">firefox&nbsp;3</a></li> <li>&nbsp; <a href="#">safari&nbsp;4</a></li> <li class="last">&nbsp; <a href="#">chrome&nbsp;2</a> &nbsp; &nbsp;</li> </ul> </body></html> and Here is the code for the svg: <?xml version="1.0" encoding="utf-8"?> <!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd"> <svg version="1.1" id="Layer_1" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" x="0px" y="0px" width="321.026px" height="44.398px" viewBox="39.487 196.864 321.026 44.398" enable-background="new 39.487 196.864 321.026 44.398" xml:space="preserve"> <linearGradient id="SVGID_1_" gradientUnits="userSpaceOnUse" x1="280" y1="316.8115" x2="280" y2="275.375" gradientTransform="matrix(1 0 0 1 -80 -77)"> <stop offset="0" style="stop-color:#5A4A6A"/> <stop offset="0.3532" style="stop-color:#605170"/> <stop offset="0.8531" style="stop-color:#726382"/> <stop offset="1" style="stop-color:#796A89"/> </linearGradient> <path fill="url(#SVGID_1_)" d="M360,238.721c0,1.121-0.812,2.029-1.812,2.029H41.813c-1.001,0-1.813-0.908-1.813-2.029v-39.316 c0-1.119,0.812-2.027,1.813-2.027h316.375c1.002,0,1.812,0.908,1.812,2.027V238.721z"/> <path opacity="0.1" fill="#FFFFFF" enable-background="new " d="M358.188,197.376H41.813c-1.001,0-1.813,0.908-1.813,2.028 v39.316c0,1.12,0.812,2.028,1.813,2.028h316.375c1,0,1.812-0.908,1.812-2.028v-39.316C360,198.284,359.189,197.376,358.188,197.376z M358.75,238.721c0,0.415-0.264,0.779-0.562,0.779H41.813c-0.3,0-0.563-0.363-0.563-0.779v-39.316c0-0.414,0.263-0.777,0.563-0.777 h316.375c0.301,0,0.562,0.363,0.562,0.777V238.721z"/> <path opacity="0.5" fill="#FFFFFF" enable-background="new " d="M358.188,197.376H41.813c-1.001,0-1.813,0.908-1.813,2.028v1.461 c0-1.12,0.812-2.028,1.813-2.028h316.375c1.002,0,1.812,0.908,1.812,2.028v-1.461C360,198.284,359.189,197.376,358.188,197.376z"/> <g id="seperators"> <line fill="none" stroke="#000000" stroke-width="1.0259" stroke-miterlimit="10" x1="104.5" y1="197.375" x2="104.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="103.5" y1="197.375" x2="103.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="105.5" y1="197.375" x2="105.5" y2="240.75"/> <line fill="none" stroke="#000000" stroke-width="1.0259" stroke-miterlimit="10" x1="167.5" y1="197.375" x2="167.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="166.5" y1="197.375" x2="166.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="168.5" y1="197.375" x2="168.5" y2="240.75"/> <line fill="none" stroke="#000000" stroke-width="1.0259" stroke-miterlimit="10" x1="231.5" y1="197.375" x2="231.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="232.5" y1="197.375" x2="232.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="230.5" y1="197.375" x2="230.5" y2="240.75"/> <line fill="none" stroke="#000000" stroke-width="1.0259" stroke-miterlimit="10" x1="295.5" y1="197.375" x2="295.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="294.5" y1="197.375" x2="294.5" y2="240.75"/> <line opacity="0.1" fill="none" stroke="#FFFFFF" stroke-width="1.0259" stroke-miterlimit="10" enable-background="new " x1="296.5" y1="197.375" x2="296.5" y2="240.75"/> </g> <path fill="none" stroke="#000000" stroke-width="1.0259" stroke-miterlimit="10" d="M360,238.721c0,1.121-0.812,2.029-1.812,2.029 H41.813c-1.001,0-1.813-0.908-1.813-2.029v-39.316c0-1.119,0.812-2.027,1.813-2.027h316.375c1.002,0,1.812,0.908,1.812,2.027 V238.721z"/> </svg> I appreciate and welcome any and all comments, help, and suggestions. Thanks in Advance!

    Read the article

  • Phonegap bluetooth plugin not working

    - by user2907333
    First time poster here , so I'm sorry if this question is asked incorrect or if there are any issues. I'm working on a phonegap app for which I need to be able to set up a bluetooth connection between a tablet (android in this case) and a Win CE PC. Currently i'm trying to get the bluetooth part to work on the tablet and i'm using the plug in you can find at https://github.com/tanelih/phonegap-bluetooth-plugin And for the momemt I'm just trying to enable and disable the Bluetooth on the device. In my bluetoothpage.js file i'm using the following method window.bluetooth.prototype.enable(bluetoothTestSucces(),bluetoothTestFail()); The bluetoothTestSucces and bluetoothTestFail functions just show an alert, nothing else. And if i understand the working of phonegap plugins correctly this uses the following code in my bluetooth.js file Bluetooth.prototype.enable = function(onSuccess, onError) { exec(onSuccess, onError, "Bluetooth", "enable", []); } which calls private void enable(JSONArray args, CallbackContext callbackCtx) { try { _bluetooth.enable(); callbackCtx.success(); } catch(Exception e) { this.error(callbackCtx, e.getMessage(), BluetoothError.ERR_UNKNOWN); } } in my BluetoothPlugin.java file. And if the java file returns Succes bluetoothTestSucces() is used and if the java file returns an error bluetoothTestFail() is used. But for some reason it runs both and does not turn on bluetooth on my device. I'm almost certain I've forgotten a link to a file or have linked it wrong somewhere. But I've followed the instructions that were included in the plugin. I've included the Bluetooth permission in my AndoridManifest file which is located in the root directory of my app I've included the plugin in my config.xml file which is located in res/xml I've required the plugin after the deviceready event as follows document.addEventListener("deviceready", onDeviceReady, false); function onDeviceReady() { window.bluetooth = cordova.require("cordova/plugin/bluetooth"); } Could anyone tell me how to fix this or what i've done wrong? thanks Martijn PS: I'm sorry for any language errors, English isn't my native language. edit: forgot to include some code

    Read the article

  • ViewStateMode in ASP.Net 4.0

    - by sreejukg
    When asp.net introduced the concept of viewstate, it changed the way how developers maintain the state for the controls in a web page. Until then to keep the track of the control(in classic asp), it was the developer responsibility to manually assign the posted content before rendering the control again. Viewstate made allowed the developer to do it with ease. The developers are not bothered about how controls keep there state on post back. Viewstate is rendered to the browser as a hidden variable __viewstate. Since viewstate stores the values of all controls, as the number of controls in the page increases, the content of viewstate grows large. It causes some websites to load slowly. As developers we need viewstate, but actually we do not want this for all the controls in the page. Till asp.net 3.5, if viewstate is disabled from web.config (using <pages viewstate=”false”/> ..</pages>), then you can not enable it from the control level/page level. Both <%@ Page EnableViewState=”true”…. and <asp:textbox EnableViewState=”true” will not work in this case. Lot of developers demands for more control over viewstate. It will be useful if the developers are able to disable it for the entire page and enable it for only those controls that needed viewstate. With ASP.NET 4.0, this is possible, a happy news for the developers. This is achieved by introducing a new property called ViewStateMode. Let us see, What is ViewStateMode – Is a new property in asp.net 4.0, that allows developers to enable viewstate for individual control even if the parent has disabled it. This ViewStateMode property can contain either of three values Enabled- Enable view state for the control even if the parent control has view state disabled. Disabled - Disable view state for this control even if the parent control has view state enabled Inherit - Inherit the value of ViewStateMode from the parent, this is the default value. To disable view state for a page and to enable it for a specific control on the page, you can set the EnableViewState property of the page to true, then set the ViewStateMode property of the page to Disabled, and then set the ViewStateMode property of the control to Enabled. Find the example below. Page directive - <%@ Page Language="C#"  EnableViewState="True" ViewStateMode="Disabled" .......... %> Code for the control  - <asp:TextBox runat="server" ViewStateMode="Enabled" ............../> Now the viewstate will be disabled for the whole page, but enabled for the TextBox. ViewStateMode gives developers more control over the viewstate.

    Read the article

  • Sesame update du jour: SL 4, OOB, Azure, and proxy support

    - by Fabrice Marguerie
    I've just published a new version of Sesame Data Browser. Here's what's new this time: Upgraded to Silverlight 4 Can run out-of-browser (OOB), with elevated permissions. This gives you an icon on your desktop and enables new scenarios. Note: The application is unsigned for the moment. Support for Windows Azure authentication Support for SQL Azure authentication If you are behind a proxy that requires authentication, just give Sesame a new try after clicking on "If you are behind a proxy that requires authentication, please click here" An icon and a button for closing connections are now displayed on connection tabsSome less visible improvements Here is the connection view with anonymous access: If you want to access Windows Azure tables as OData, all you have to do is use your table storage endpoint as the URL, and provide your access key: A Windows Azure table storage address looks like this: http://<your account>.table.core.windows.net/ If you want to browse your SQL Azure databases with Sesame, you have to enable OData support for them at https://www.sqlazurelabs.com/ConfigOData.aspx. I won't show how it works because it's already been done in several places over the Web. Here are pointers: OData.org: Got SQL Azure? Then you've got OData OakLeaf Systems: Enabling and Using the OData Protocol with SQL Azure Patrick Verbruggen: Creating an OData feed for your Azure databases Shawn Wildermuth: SQL Azure's OData Support Jack Greenfield: How to Use OData for SQL Azure with AppFabric Access Control You can choose to enable anonymous access or not. When you don't enable anonymous access, you have to provide an Issuer name and a Secret key, and optionally an Security Token Service (STS) endpoint: Excerpt from Jack Greenfield's blog: To enable OData access to the currently selected database, check the box labeled "Enable OData". When OData access is enabled, database user mapping information is displayed at the bottom of the form.Use the drop down list labeled "Anonymous Access User" to select an anonymous access user. If an anonymous access user is selected, then all queries against the database presented without credentials will execute by impersonating that user. You can access the database as the anonymous user by clicking on the link provided at the bottom of the page. If no anonymous access user is selected, then the OData Service will not allow anonymous access to the database.Click the link labeled "Add User" to add a user for authenticated access. In the pop up panel, select the user from the drop down list. Leave the issuer name empty for simple authentication, or provide the name of a trusted Security Token Service (STS) for federated authentication. For example, to federate with another ACS based STS, provide the base URI for the STS endpoint displayed by the Windows Azure AppFabric Portal for the STS.Click the "OK" button to complete the configuration process and dismiss the pop up panel. When one or more authenticated access users are added, the OData Service will impersonate them when appropriate credentials are presented. You can designate as many authenticated access users as you like. The OData Service will decide which one to impersonate for each query by inspecting the credentials presented with the query.Next time I'll give an overview of how Sesame Data Browser is built.In the meantime, happy data browsing!

    Read the article

  • Turn off keyboard back-light Sony (VAIO SVF1521DCXW)

    - by KasiyA
    I have a Sony laptop and I want to turn keyboard back-light off. It doesn't have a shortcut function key for doing this on the keyboard . I can turn off it with VAIO Control Center in Windows but I don't know how can I turn it off in Ubuntu 14.04. There isn't available to me: /sys/devices/platform/sony-laptop/kbd_backlight doesn't exist on my machine. I have this folder /sys/devices/platform/sony-laptop/ and there is three folder one power folder and two shortcut-ed folder driver , subsystem and five file contains battery_care_health , battery_care_limiter , modalias , touchpad and event This is the output of running sudo modinfo sony-laptop: filename: /lib/modules/3.13.0-34-generic/kernel/drivers/platform/x86/sony-laptop.ko version: 0.6 license: GPL description: Sony laptop extras driver (SPIC and SNC ACPI device) author: Stelian Pop, Mattia Dongili srcversion: 5C6E050349475558A231C59 alias: acpi*:SNY6001:* alias: acpi*:SNY5001:* depends: intree: Y vermagic: 3.13.0-34-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: 50:0B:C5:C8:7D:4B:11:5C:F3:C1:50:4F:7A:92:E2:33:C6:14:3D:58 sig_hashalgo: sha512 parm: debug:set this to 1 (and RTFM) if you want to help the development of this driver (int) parm: no_spic:set this if you don't want to enable the SPIC device (int) parm: compat:set this if you want to enable backward compatibility mode (int) parm: mask:set this to the mask of event you want to enable (see doc) (ulong) parm: camera:set this to 1 to enable Motion Eye camera controls (only use it if you have a C1VE or C1VN model) (int) parm: minor:minor number of the misc device for the SPIC compatibility code, default is -1 (automatic) (int) parm: kbd_backlight:set this to 0 to disable keyboard backlight, 1 to enable it (default: no change from current value) (int) parm: kbd_backlight_timeout:meaningful values vary from 0 to 3 and their meaning depends on the model (default: no change from current value) (int) With the suggested command: sudo modprobe -r sony_laptop sudo modprobe -v sony_laptop kbd_backlight=0 Output was: insmod /lib/modules/3.13.0-34-generic/kernel/drivers/platform/x86/sony-laptop.ko kbd_backlight=0 It doesn't seem to affect the keyboard backlight. And also trying this command: sudo modprobe -v sony_laptop kbd_backlight_timeout=3 kbd_backlight=0 and doesn't seem to effect the keyboard backlight I also test it after restart laptop, And I didn't see any effect too. Important : By default, keyboard backlight is off; when I press a key it turns on and after 15 seconds it turns off again. It's the same result on battery and AC power I followed also http://ubuntuforums.org/showthread.php?t=2139597 and Keyboard backlighting not working on a Vaio VPCSB11FX but didn't work so.

    Read the article

  • WMI Rights required to read root\MicrosoftIISv2 in IIS7 with IIS6 compatibility mode

    - by JoeBilly
    I need to manage my IIS7 (Windows Server 2008) remotely with a WMI IIS6 API. So I added the IIS6 WMI Compatibility and IIS6 Metabase Compatibility roles to access the root\MicrosoftIIsv2 namespace. I have a domain account which is not administrator on the remote machine ; with this right, everything is ok. I configured these rights for my domain account to access the root\MicrosoftIIsv2 WMI namespace remotely ; note that these rights work perfectly on a IIS6 and Windows Server 2003 : DCOM : Account in Distributed COM Users Remote & local access to DCOM WMI : Root\CIMV2 (I need access here too) Execute methods, Enable Account, Remote Enable Root\Default (I need access here too) Execute methods, Enable Account, Remote Enable Root\MicrosoftIISv2 Execute methods, Enable Account, Provider Write, Remote Enable IIS Metabase (Metabase Explorer) : LM Full Control (W3SVC inherits these permissions) I tried to give some access on C:\Windows\System32\inetsrv too ; don't know if needed. My issue is : I can't list the IIS WebSites (\root\MicrosoftIISv2:IIsWebServerSetting.Name="W3SVC/*"). I don't get an 'access denied' but nothing is returned. My API and powershell tests can connect and execute queries in the root\MicrosoftIISv2 namespace I can read the IIsComputer class ex: Get-WmiObject IIsComputer -namespace "ROOT\MicrosoftIISv2" -authentication PacketPrivacy | SELECT * I can't read the IIsWebServerSetting, IIsWebServer ... to list the WebSites : the query returns an empty collection ex: Get-WmiObject IIsWebServerSetting -namespace "ROOT\MicrosoftIISv2" -authentication PacketPrivacy | SELECT ServerComment All queries work perfectly if the account is administrator as already said I am using PacketPrivacy authentication FI: I got a Warning Event 5605 with the Administrator right or not, that does not seem to have an impact : The root\MicrosoftIISv2 namespace is marked with the RequiresEncryption flag. Access to this namespace might be denied if the script or application does not have the appropriate authentication level. Change the authentication level to Pkt_Privacy and run the script or application again Ok, I have some more informations, when I use IIS 6 Metabase Explorer with my administrator account I can see the rights are correctly inherited for my non-administrator account. But when I try to connect using my non-administrator account, I can list the LM node, but get an "access denied, failed to get a key's data" when I try to browse the child nodes. I'll check further. I tried to Trace the WMI Activity, and everything seems OK ; this tends to confirm that the problem lies in IIS Rights.

    Read the article

  • Does enabling SMB2 on a NetApp filer require a cifs restart?

    - by Sim
    I would like to enable SMB2 on a FAS 2050 running Data ONTAP 7.3.2 as by default it is disabled. I have discovered that to enable SMB2 the following option must be set: options cifs.smb2.client.enable on Does this require a restart of cifs to take affect or just does it start working magically? Also will this change persist across a reboot?

    Read the article

  • "No bootable device - insert boot disk" after restart on Ubuntu 10.04 b1 update

    - by anjanesh
    I was making an update on my Ubuntu 10.04 beta1 64-bit PC when, after reboot I get PXE-E61: Mediaa test failure, check cable PXE-M0F: Exiting Intel Boot Agent. No bootable device - insert boot disk and press any key How did my boot record disappear ? BIOS Boot Boot Menu Type : Normal Boot Device Priority : <CD/DVD-ROM Drive> <Hard Disk Drive> <Floppy Drive> <Ethernet> Hard Driver Order : No Hard Disk Drive CD/DVD ROM Drive Order : <PT-TSSTcorp CDDV> Removable Drive Order : No Removable Drive Boot to Optical Devices : <Enable> Boot to Removable Devices : <Enable> Boot to Network : <Enable> USB Boot : <Enable>

    Read the article

  • How to upgrade Apache 2 from 2.2 to 2.4

    - by Nina
    I was in the process of doing a test upgrade from Apache 2.2 to 2.4.3. I'm using Ubuntu 10.04. I would have upgraded to 12.04 for this to see if the upgrade would go a lot smoother. Unfortunately, I was told it wasn't an option...so I'm stuck using 10.04. The process I did this was: Before attempting this, I have managed to upgrade APR from 1.3 to 1.4 as well since apache told me it was a requirement beforehand: http://apr.apache.org/download.cgi First remove all traces of the current apache: sudo apt-get --purge remove apache2 sudo apt-get remove apache2-common apache2-utils apache2.2-bin apache2-common sudo apt-get autoremove whereis apache2 sudo rm -Rf /etc/apache2 /usr/lib/apache2 /usr/include/apache2 Afterwards, I did the following: sudo apt-get install build-essential sudo apt-get build-dep apache2 Then install apache 2.4 with the following: wget http://apache.mirrors.tds.net//httpd/httpd-2.4.3.tar.gz tar -xzvf httpd-2.4.3.tar.gz && cd httpd-2.4.3 sudo ./configure --prefix=/usr/local/apache2 --with-apr=/usr/local/apr --enable-mods-shared=all --enable-deflate --enable-proxy --enable-proxy-balancer --enable-proxy-http --with-mpm=prefork sudo make sudo make install After the make install, I ended up getting a series of errors that prevented it from installing correctly: exports.c:2513: error: redefinition of 'ap_hack_apr_uid_current' exports.c:1838: note: previous definition of 'ap_hack_apr_uid_current' was here exports.c:2514: error: redefinition of 'ap_hack_apr_uid_name_get' exports.c:1839: note: previous definition of 'ap_hack_apr_uid_name_get' was here exports.c:2515: error: redefinition of 'ap_hack_apr_uid_get' exports.c:1840: note: previous definition of 'ap_hack_apr_uid_get' was here exports.c:2516: error: redefinition of 'ap_hack_apr_uid_homepath_get' Looking for exports.c only leads me back to the httpd-2.4.3 folder. So I'm not sure what these errors mean... Thanks in advance for any help you have to offer!

    Read the article

  • Initial Cisco ASA 5510 Config

    - by Brendan ODonnell
    Fair warning, I'm a but of a noob so please bear with me. I'm trying to set up a new ASA 5510. I have a pretty simple set up with one /24 on the inside NATed to a DHCP address on the outside. Everything on the inside works and I can ping the outside interface from external devices. No matter what I do I can't get anything internal to route across the border to the outside and back. To try and eliminate ACL issues as a possibility I added permit any any rules to the incoming access lists on the inside and outside interfaces. I'd appreciate any help I can get. Here's the sh run. : Saved : ASA Version 8.4(3) ! hostname gateway domain-name xxx.local enable password xxx encrypted passwd xxx encrypted names ! interface Ethernet0/0 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/1 nameif inside security-level 100 ip address 10.x.x.x 255.255.255.0 ! interface Ethernet0/2 shutdown no nameif no security-level no ip address ! interface Ethernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 nameif management security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! ftp mode passive dns domain-lookup inside dns server-group DefaultDNS name-server 10.x.x.x domain-name xxx.local same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-network subnet 10.x.x.x 255.255.255.0 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list outside_access_in extended permit ip any any access-list inside_access_in extended permit ip any any pager lines 24 logging enable logging buffered informational logging asdm informational mtu management 1500 mtu inside 1500 mtu outside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside icmp permit any outside no asdm history enable arp timeout 14400 ! object network inside-network nat (any,outside) dynamic interface access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL aaa authentication ssh console LOCAL aaa authentication http console LOCAL http server enable http 192.168.1.0 255.255.255.0 management http 10.x.x.x 255.255.255.0 inside http authentication-certificate management http authentication-certificate inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart telnet timeout 5 ssh 192.168.1.0 255.255.255.0 management ssh 10.x.x.x 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 dhcp-client client-id interface outside dhcpd address 192.168.1.2-192.168.1.254 management dhcpd enable management ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn username xxx password xxx encrypted ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options inspect icmp ! service-policy global_policy global prompt hostname context no call-home reporting anonymous Cryptochecksum:fe19874e18fe7107948eb0ada6240bc2 : end no asdm history enable

    Read the article

  • "No bootable device - insert boot disk" after restart on Ubuntu 10.04 b1 update

    - by anjanesh
    I was making an update on my Ubuntu 10.04 beta1 64-bit PC when, after reboot I get PXE-E61: Mediaa test failure, check cable PXE-M0F: Exiting Intel Boot Agent. No bootable device - insert boot disk and press any key How did my boot record disappear ? BIOS Boot Boot Menu Type : Normal Boot Device Priority : <CD/DVD-ROM Drive> <Hard Disk Drive> <Floppy Drive> <Ethernet> Hard Driver Order : No Hard Disk Drive CD/DVD ROM Drive Order : <PT-TSSTcorp CDDV> Removable Drive Order : No Removable Drive Boot to Optical Devices : <Enable> Boot to Removable Devices : <Enable> Boot to Network : <Enable> USB Boot : <Enable>

    Read the article

  • Cisco ASA: Allowing and Denying VPN Access based on membership to an AD group

    - by milkandtang
    I have a Cisco ASA 5505 connecting to an Active Directory server for VPN authentication. Usually we'd restrict this to a particular OU, but in this case users which need access are spread across multiple OUs. So, I'd like to use a group to specify which users have remote access. I've created the group and added the users, but I'm having trouble figuring out how to deny users which aren't in that group. Right now, if someone connects they get assigned the correct group policy "companynamera" if they are in that group, so the LDAP mapping is working. However, users who are not in that group still authenticate fine, and their group policy becomes the LDAP path of their first group, i.e. CN=Domain Users,CN=Users,DC=example,DC=com, and then are still allowed access. How do I add a filter so that I can map everything that isn't "companynamera" to no access? Config I'm using (with some stuff such as ACLs and mappings removed, since they are just noise here): gateway# show run : Saved : ASA Version 8.2(1) ! hostname gateway domain-name corp.company-name.com enable password gDZcqZ.aUC9ML0jK encrypted passwd gDZcqZ.aUC9ML0jK encrypted names name 192.168.0.2 dc5 description FTP Server name 192.168.0.5 dc2 description Everything server name 192.168.0.6 dc4 description File Server name 192.168.0.7 ts1 description Light Use Terminal Server name 192.168.0.8 ts2 description Heavy Use Terminal Server name 4.4.4.82 primary-frontier name 5.5.5.26 primary-eschelon name 172.21.18.5 dmz1 description Kerio Mail Server and FTP Server name 4.4.4.84 ts-frontier name 4.4.4.85 vpn-frontier name 5.5.5.28 ts-eschelon name 5.5.5.29 vpn-eschelon name 5.5.5.27 email-eschelon name 4.4.4.83 guest-frontier name 4.4.4.86 email-frontier dns-guard ! interface Vlan1 nameif inside security-level 100 ip address 192.168.0.254 255.255.255.0 ! interface Vlan2 description Frontier FiOS nameif outside security-level 0 ip address primary-frontier 255.255.255.0 ! interface Vlan3 description Eschelon T1 nameif backup security-level 0 ip address primary-eschelon 255.255.255.248 ! interface Vlan4 nameif dmz security-level 50 ip address 172.21.18.254 255.255.255.0 ! interface Vlan5 nameif guest security-level 25 ip address 172.21.19.254 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport access vlan 3 ! interface Ethernet0/2 switchport access vlan 4 ! interface Ethernet0/3 switchport access vlan 5 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS name-server dc2 domain-name corp.company-name.com same-security-traffic permit intra-interface access-list companyname_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0 access-list companyname_splitTunnelAcl standard permit 172.21.18.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.20.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.18.0 255.255.255.0 access-list bypassingnat_dmz extended permit ip 172.21.18.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 12288 logging buffered warnings logging asdm notifications mtu inside 1500 mtu outside 1500 mtu backup 1500 mtu dmz 1500 mtu guest 1500 ip local pool VPNpool 172.21.20.50-172.21.20.59 mask 255.255.255.0 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 email-frontier global (outside) 3 guest-frontier global (backup) 1 interface global (dmz) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 dc5 255.255.255.255 nat (inside) 1 192.168.0.0 255.255.255.0 nat (dmz) 0 access-list bypassingnat_dmz nat (dmz) 2 dmz1 255.255.255.255 nat (dmz) 1 172.21.18.0 255.255.255.0 access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 4.4.4.1 1 track 1 route backup 0.0.0.0 0.0.0.0 5.5.5.25 254 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 ldap attribute-map RemoteAccessMap map-name memberOf IETF-Radius-Class map-value memberOf CN=RemoteAccess,CN=Users,DC=corp,DC=company-name,DC=com companynamera dynamic-access-policy-record DfltAccessPolicy aaa-server ActiveDirectory protocol ldap aaa-server ActiveDirectory (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft aaa-server ADRemoteAccess protocol ldap aaa-server ADRemoteAccess (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft ldap-attribute-map RemoteAccessMap aaa authentication enable console LOCAL aaa authentication ssh console LOCAL http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sla monitor 123 type echo protocol ipIcmpEcho 4.4.4.1 interface outside num-packets 3 frequency 10 sla monitor schedule 123 life forever start-time now crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 ! track 1 rtr 123 reachability telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 management-access inside dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy companynamera internal group-policy companynamera attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com group-policy companyname internal group-policy companyname attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com username admin password IhpSqtN210ZsNaH. encrypted privilege 15 tunnel-group companyname type remote-access tunnel-group companyname general-attributes address-pool VPNpool authentication-server-group ActiveDirectory LOCAL default-group-policy companyname tunnel-group companyname ipsec-attributes pre-shared-key * tunnel-group companynamera type remote-access tunnel-group companynamera general-attributes address-pool VPNpool authentication-server-group ADRemoteAccess LOCAL default-group-policy companynamera tunnel-group companynamera ipsec-attributes pre-shared-key * ! class-map type inspect ftp match-all ftp-inspection-map class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect ftp ftp-inspection-map parameters class ftp-inspection-map policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns migrated_dns_map_1 inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect ils inspect netbios inspect rsh inspect rtsp inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp inspect icmp inspect icmp error inspect esmtp inspect pptp ! service-policy global_policy global prompt hostname context Cryptochecksum:487525494a81c8176046fec475d17efe : end gateway# Thanks so much!

    Read the article

  • Error in Bind9 named.conf file. Bind won't start.

    - by tj111
    I'm trying to setup a DNS server on an Ubuntu Server machine (10.04). I configured an entry in named.conf.local to test it, but when trying to restart bind9 I get the following error: * Starting domain name service... bind9 [fail] So I checked the output of syslog and this is what I get. May 20 18:11:13 empression-server1 named[4700]: starting BIND 9.7.0-P1 -u bind May 20 18:11:13 empression-server1 named[4700]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' May 20 18:11:13 empression-server1 named[4700]: adjusted limit on open files from 1024 to 1048576 May 20 18:11:13 empression-server1 named[4700]: found 4 CPUs, using 4 worker threads May 20 18:11:13 empression-server1 named[4700]: using up to 4096 sockets May 20 18:11:13 empression-server1 named[4700]: loading configuration from '/etc/bind/named.conf' May 20 18:11:13 empression-server1 named[4700]: /etc/bind/named.conf:10: missing ';' before 'include' May 20 18:11:13 empression-server1 named[4700]: loading configuration: failure May 20 18:11:13 empression-server1 named[4700]: exiting (due to fatal error) So it thinks I have an error in the default named.conf file, which is pretty ridiculous. I went through it and deleted a blank line just for the hell of it, but I can't see how it figures there's an error in there. Note that before this I did have an error in named.conf.local, but it showed up properly in syslog and I fixed it, so it is reporting the correct file. Here is the contents of named.conf: // This is the primary configuration file for the BIND DNS server named. // // Please read /usr/share/doc/bind9/README.Debian.gz for information on the // structure of BIND configuration files in Debian, *BEFORE* you customize // this configuration file. // // If you are just adding zones, please do that in /etc/bind/named.conf.local include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones";

    Read the article

  • PHP FastCGI/XML/DOM Configure

    - by James
    Guys, any ideas why when I configure PHP 5.3.1, these options fail? Notice: Following unknown configure options were used: --with-xml --with-dom --enable-fastcgi --enable-discard-path --enable-force-cgi-redirect

    Read the article

  • VirtualBox: Host OS processor is spiked while guest OS virtual processor is idle?

    - by Greg Mattes
    I'm running Windows XP 32-bit on Windows Vista 64-bit with VirtualBox 3.0.6. Whenever I run the XP VM, Vista (host) reports 100% cpu utilization even though XP (guest) reports between 1-5% cpu utilization. The host box has 2 GB of physical RAM. The guest/vm is configured with 512 MB. The host box has a 64-bit AMD processor. No apps (other than VirtualBox) are running on either host, they're just idling. Any guesses as to why the host processor is spiked? I've enabled various advanced features for the XP guest in the hopes of having better performance: Settings → System → Motherboard: Enable IO APIC Settings → System → Processor: Enable PAE/NX Settings → System → Acceleration: Enable VT-x/AMD-V and Enable Nesting Paging

    Read the article

  • Loss of feature set with VMware EVC

    - by Peter
    If I have two machines both 3rd Generation AMD Opteron, one Shanghai & one Istanbul and I can vMotion between them. Does it buy me anything to enable EVC at the 3rd Generation AMD level? Will I lose any CPU features? My thoughts are, I can enable EVC 3rd Generation with running VMs and I can't enable 2nd Generation EVC with running VMs. I figure there won't be a lose in any features because if there was a reduction in feature set then I couldn't enable EVC with running VMs.

    Read the article

  • bind9 named.conf zones size limit

    - by mox601
    I am trying to set up a test environment on my local machine, and I am trying to start a DNS daemon that loads tha configuration from a named.conf.custom file. As long as the size of that file is like 3-4 zones, the bind9 daemon loads fine, but when i enter the config file i need (like 10000 lines long), bind can't startup and in the syslog i find this message: starting BIND 9.7.0-P1 -u bind Jun 14 17:06:06 cibionte-pc named[9785]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' Jun 14 17:06:06 cibionte-pc named[9785]: adjusted limit on open files from 1024 to 1048576 Jun 14 17:06:06 cibionte-pc named[9785]: found 1 CPU, using 1 worker thread Jun 14 17:06:06 cibionte-pc named[9785]: using up to 4096 sockets Jun 14 17:06:06 cibionte-pc named[9785]: loading configuration from '/etc/bind/named.conf' Jun 14 17:06:06 cibionte-pc named[9785]: /etc/bind/named.conf.saferinternet:1: unknown option 'zone' Jun 14 17:06:06 cibionte-pc named[9785]: loading configuration: failure Jun 14 17:06:06 cibionte-pc named[9785]: exiting (due to fatal error) Are there any limits on the file size bind9 is allowed to load?

    Read the article

  • How to convert .flv file to .3gp using ffmpeg?

    - by Chetana
    I have converted any video format to 3gp file format using ffmpeg on one server. But on another server it not works. Following is my script: exec("ffmpeg -i test.flv -sameq -acodec libmp3lame -ar 22050 -ab 96000 -deinterlace -nr 500 -s 320x240 -aspect 4:3 -r 20 -g 500 -me_range 20 -b 270k -deinterlace -f flv -y test.3gp "); Can anyone tell me what is wrong in script? Following is my ffmpeg setting: root@ninja [~]# ffmpeg -formats ffmpeg version CVS, build 3277056, Copyright (c) 2000-2004 Fabrice Bellard configuration: --enable-mp3lame --enable-libogg --enable-gpl --disable-mmx --enable-shared built on Jun 17 2009 10:51:43, gcc: 4.1.2 20080704 (Red Hat 4.1.2-44)

    Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >