Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 41/315 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

• How to set-up DSL dialer for Ubuntu 12.04 LTS

  - by Mohammad Yaseen

  I have just installed Ubuntu 12.04 LTS and I'm unable to get my DSL dialer working properly. To set this up in Windows 7 I had to do following: Control Panel --- Network and Intertnet Network and sharing center --- Setup a new network or connection Connect to the internet --- Broadband PPPoE Enter username and Password.. CLick 'Connect' and Done. I am doing following steps in Ubuntu with no luck: Click on 'Two Arrows' (i don't know what they are called) on upper right corner. Configure VPN --- DSL tab --- Add Then I entered username, password, MAC address and Clone MAC address (copied from Auto Ethernet). Save The same set up used to work with Ubuntu 10.10 but it is not working here. Now whenever I click on DSL Connection 1 to connect dialer 'Auto Ethernet' gets disconneted and I end up with no Internet connection. I am new to Ubuntu, Please suggest some easy steps. I have installed ubuntu alongside windows. And dialer works fine in Windows environment, i am writing this in Windows .

  Read the article

• Skipping video and audio with PS3MediaServer

  - by MaxMackie

  I'm using the latest PS3MediaServer build right from the repos suggested in the Ubuntu Wiki. I'm streaming multiple movies from my server (Ubuntu 10.04 LTS) to my PS3 over wireless. Sometimes, during some movies, the audio and the video will begin skipping. This can last anywhere between 5 and 30 seconds before it goes back to normal. I have a four core i5 processor and 8GB of DDR3 RAM so I don't think my computer is having a hard time keeping up with the transcoding. So this leads me to believe it's either sub-optimal transcoding options from within PS3MS or my network can't handle the heat. Other than the out-of-box configuration, is there any way I can tweak the settings for the application to use my resources more efficiently?

  Read the article

• Wifi hotspot to connect to Android using non-AP supported cards

  - by 3l4ng

  I'm running Ubuntu 13.10 64b on a Dell Inspiron N5010. My wireless device (found using lspci) is Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01). I bought a new android phone and want to connect to Internet by using the laptop as a Wireless Access Point (ad-hoc doesn't work with Android). I tried following tutorials like the one at How to setup a wi-fi hotspot (access point mode)?. The relevant output from iw list was Supported interface modes: * IBSS * managed Running sudo hostapd /path/to/conf/file gave me (eth1 is the wireless, verified by iwconfig) Failed to create interface mon.eth1: -95 (Operation not supported) Could not set channel for kernel driver eth1: Unable to setup interface. Could not connect to kernel driver. I am able to use Connectify and Virtualrouter on Windows, and the phone works great. How do I get an access point running on Ubuntu? I'm open to other alternatives as well.

  Read the article

• Library like ENet, but for TCP?

  - by Milo

  I'm not looking to use boost::asio, it is overly complex for my needs. I'm building a game that is cross platform, for desktop, iPhone and Android. I found a library called ENet which is pretty much what I need, but it uses UDP which does not seem to support encryption and a few other things. Given that the game is an event driven card game, TCP seems like the right fit. However, all I have found is WINSOCK / berkley sockets and bost::asio. Here is a sample client server application with ENet: #include <enet/enet.h> #include <stdlib.h> #include <string> #include <iostream> class Host { ENetAddress address; ENetHost * server; ENetHost* client; ENetEvent event; public: Host() :server(NULL) { enet_initialize(); setupServer(); } void setupServer() { if(server) { enet_host_destroy(server); server = NULL; } address.host = ENET_HOST_ANY; /* Bind the server to port 1234. */ address.port = 1721; server = enet_host_create (& address /* the address to bind the server host to */, 32 /* allow up to 32 clients and/or outgoing connections */, 2 /* allow up to 2 channels to be used, 0 and 1 */, 0 /* assume any amount of incoming bandwidth */, 0 /* assume any amount of outgoing bandwidth */); } void daLoop() { while(true) { /* Wait up to 1000 milliseconds for an event. */ while (enet_host_service (server, & event, 5000) > 0) { ENetPacket * packet; switch (event.type) { case ENET_EVENT_TYPE_CONNECT: printf ("A new client connected from %x:%u.\n", event.peer -> address.host, event.peer -> address.port); /* Store any relevant client information here. */ event.peer -> data = "Client information"; /* Create a reliable packet of size 7 containing "packet\0" */ packet = enet_packet_create ("packet", strlen ("packet") + 1, ENET_PACKET_FLAG_RELIABLE); /* Extend the packet so and append the string "foo", so it now */ /* contains "packetfoo\0" */ enet_packet_resize (packet, strlen ("packetfoo") + 1); strcpy ((char*)& packet -> data [strlen ("packet")], "foo"); /* Send the packet to the peer over channel id 0. */ /* One could also broadcast the packet by */ /* enet_host_broadcast (host, 0, packet); */ enet_peer_send (event.peer, 0, packet); /* One could just use enet_host_service() instead. */ enet_host_flush (server); break; case ENET_EVENT_TYPE_RECEIVE: printf ("A packet of length %u containing %s was received from %s on channel %u.\n", event.packet -> dataLength, event.packet -> data, event.peer -> data, event.channelID); /* Clean up the packet now that we're done using it. */ enet_packet_destroy (event.packet); break; case ENET_EVENT_TYPE_DISCONNECT: printf ("%s disconected.\n", event.peer -> data); /* Reset the peer's client information. */ event.peer -> data = NULL; } } } } ~Host() { if(server) { enet_host_destroy(server); server = NULL; } atexit (enet_deinitialize); } }; class Client { ENetAddress address; ENetEvent event; ENetPeer *peer; ENetHost* client; public: Client() :peer(NULL) { enet_initialize(); setupPeer(); } void setupPeer() { client = enet_host_create (NULL /* create a client host */, 1 /* only allow 1 outgoing connection */, 2 /* allow up 2 channels to be used, 0 and 1 */, 57600 / 8 /* 56K modem with 56 Kbps downstream bandwidth */, 14400 / 8 /* 56K modem with 14 Kbps upstream bandwidth */); if (client == NULL) { fprintf (stderr, "An error occurred while trying to create an ENet client host.\n"); exit (EXIT_FAILURE); } /* Connect to some.server.net:1234. */ enet_address_set_host (& address, "192.168.2.13"); address.port = 1721; /* Initiate the connection, allocating the two channels 0 and 1. */ peer = enet_host_connect (client, & address, 2, 0); if (peer == NULL) { fprintf (stderr, "No available peers for initiating an ENet connection.\n"); exit (EXIT_FAILURE); } /* Wait up to 5 seconds for the connection attempt to succeed. */ if (enet_host_service (client, & event, 20000) > 0 && event.type == ENET_EVENT_TYPE_CONNECT) { std::cout << "Connection to some.server.net:1234 succeeded." << std::endl; } else { /* Either the 5 seconds are up or a disconnect event was */ /* received. Reset the peer in the event the 5 seconds */ /* had run out without any significant event. */ enet_peer_reset (peer); puts ("Connection to some.server.net:1234 failed."); } } void daLoop() { ENetPacket* packet; /* Create a reliable packet of size 7 containing "packet\0" */ packet = enet_packet_create ("backet", strlen ("backet") + 1, ENET_PACKET_FLAG_RELIABLE); /* Extend the packet so and append the string "foo", so it now */ /* contains "packetfoo\0" */ enet_packet_resize (packet, strlen ("backetfoo") + 1); strcpy ((char*)& packet -> data [strlen ("backet")], "foo"); /* Send the packet to the peer over channel id 0. */ /* One could also broadcast the packet by */ /* enet_host_broadcast (host, 0, packet); */ enet_peer_send (event.peer, 0, packet); /* One could just use enet_host_service() instead. */ enet_host_flush (client); while(true) { /* Wait up to 1000 milliseconds for an event. */ while (enet_host_service (client, & event, 1000) > 0) { ENetPacket * packet; switch (event.type) { case ENET_EVENT_TYPE_RECEIVE: printf ("A packet of length %u containing %s was received from %s on channel %u.\n", event.packet -> dataLength, event.packet -> data, event.peer -> data, event.channelID); /* Clean up the packet now that we're done using it. */ enet_packet_destroy (event.packet); break; } } } } ~Client() { atexit (enet_deinitialize); } }; int main() { std::string a; std::cin >> a; if(a == "host") { Host host; host.daLoop(); } else { Client c; c.daLoop(); } return 0; } I looked at some socket tutorials and they seemed a bit too low level. I just need something that abstracts away the platform (eg, no WINSOCKS) and that has basic ability to keep track of connected clients and send them messages. Thanks

  Read the article

• Connecting 2 ubuntu machines as a LAN

  - by Brendan Cutjar

  Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue? Thank you ANSWERED All I had to do was set up both ip's maually, subnet mask to 255.255.255.0 and left blank both gateway and DNS.

  Read the article

• Tips for debugging Samba performance?

  - by j-g-faustus

  Samba gives me 24 MB/s read and 44 MB/s write, while ftp gives 97 and 112 MB/s under the same circumstances. The documentation says that Generally, you should find that Samba performs similarly to ftp at raw transfer speed. In my case it clearly doesn't. Where can I find tips on how to debug Samba performance? Or alternatively tips for replacing Samba with something else? (I can't use ftp, unfortunately, as I need something that can be used with rsync/rsnapshot.) More details: Both computers are running Ubuntu 10.10 (using Samba because I have a Mac as well) The Samba share is on a local home network, mounted as $ mount ... //server.local/share/ on /mnt/share type cifs (rw,mand) Samba performance was tested by copying (cp) a single file of ~4GB to and from the share, using time for timing and calculating transfer speed by hand. ftp performance are the numbers from the ftp client for get/put of the same file. iperf gives network speed ~900 Mbits/s bonnie++ gives disk speeds 200 MB/s on both sides for block reads as well as block writes Tried changing the parameters suggested in the performance tuning HOWTO (read/write raw, read size, socket options), most of them made little to no difference. (The one that made a difference caused write speed to drop 50%.)

  Read the article

• Can't ping Ubuntu laptop from my LAN

  - by oskar

  My laptop has Ubuntu 10.10 and is connected to my router with full internet access, yet I can't ping it from other computers on my LAN. I tried the following: I can successfully ping those other computers from my Ubuntu laptop, so I didn't accidentally connect to someone else's network. I can successfully ping my Ubuntu laptop from itself, though I don't know if that means anything. I haven't messed with iptables at all, so it currently doesn't have any rules set that would cause it to reject anything. I made a DHCP reservation for my laptop's MAC address in my router to make sure I was always using the correct IP address. Please note that I am using a "command line only" install of Ubuntu, so I can't use any GUI network config tools. The reason I want to ping it is because I am trying to run an NFS server on the laptop, yet despite correctly setting it up I cannot access the NFS volume on another computer because it isn't even visible on the network right now.

  Read the article

• Ubuntu 12.04 // Likewise Open // Unable to ever authenticate AD users

  - by Rob

  So Ubuntu 12.04, Likewise latest from the beyondtrust website. Joins domain fine. Gets proper information from lw-get-status. Can use lw-find-user-by-name to retrieve/locate users. Can use lw-enum-users to get all users. Attempting to login with an AD user via SSH generates the following errors in the auth.log file: Nov 28 19:15:45 hostname sshd[2745]: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:15:45 hostname sshd[2745]: PAM adding faulty module: pam_winbind.so Nov 28 19:15:51 hostname sshd[2745]: error: PAM: Authentication service cannot retrieve authentication info for DOMAIN\\user.name from remote.hostname Nov 28 19:16:06 hostname sshd[2745]: Connection closed by 10.1.1.84 [preauth] Attempting to login via the LightDM itself generates similar errors in the auth.log file. Nov 28 19:19:29 hostname lightdm: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:19:29 hostname lightdm: PAM adding faulty module: pam_winbind.so Nov 28 19:19:47 hostname lightdm: pam_succeed_if(lightdm:auth): requirement "user ingroup nopasswdlogin" not met by user "DOMAIN\user.name" Nov 28 19:19:52 hostname lightdm: [lsass-pam] [module:pam_lsass]pam_sm_authenticate error [login:DOMAIN\user.name][error code:40022] Nov 28 19:19:54 hostname lightdm: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:19:54 hostname lightdm: PAM adding faulty module: pam_winbind.so Attempting to login via a console on the system itself generates slightly different errors: Nov 28 19:31:09 hostname login[997]: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:31:09 hostname login[997]: PAM adding faulty module: pam_winbind.so Nov 28 19:31:11 hostname login[997]: [lsass-pam] [module:pam_lsass]pam_sm_authenticate error [login:DOMAIN\user.name][error code:40022] Nov 28 19:31:14 hostname login[997]: FAILED LOGIN (1) on '/dev/tty2' FOR 'DOMAIN\user.name', Authentication service cannot retrieve authentication info Nov 28 19:31:31 hostname login[997]: FAILED LOGIN (2) on '/dev/tty2' FOR 'DOMAIN\user.name', Authentication service cannot retrieve authentication info I am baffled. The errors obviously are correct, the file /lib/security/pam_winbind.so does not exist. If its a dependancy/required, surely it should be part of the package? I've installed/reinstalled, I've used the downloaded package from the beyondtrust website, i've used the repository, nothing seems to work, every method of installing this application generates the same errors for me. UPDATE : Hrmm, I thought likewise didn't use native winbind but its own modules. Installing winbind from apt-get uninstalls pbis-open (likewise) and generates failures when installing if pbis-open is installed first. Uninstalled winbind, reinstalled pbis-open, same issue as above. The file pam_winbind.so does not exist in that location. Setting up pbis-open-legacy (7.0.1.918) ... Installing Packages was successful This computer is joined to DOMAIN.LOCAL New libraries and configurations have been installed for PAM and NSS. Clearly it thinks it has installed it, but it hasn't. It may be a legacy issue with the previous attempt to configure domain integration manually with winbind. Does anyone have a working likewise-open installation and does the /etc/nsswitch.conf include references to winbind? Or do the /etc/pam.d/common-account or /etc/pam.d/common-password reference pam_winbind.so? I'm unsure if those entries are just legacy or setup by likewise. UPDATE 2 : Complete reinstall of OS fixed it and it worked seamlessly, like it was meant to and those 2 PAM files did NOT include entries for pam_winbind.so, so that was the underlying problem. Thanks for the assist.

  Read the article

• OpenVPN, Server 12.04, connect to machines in home LAN behind VPN server

  - by inexion

  Problem: I've set up a working OpenVPN server, and am able to connect to it from anywhere using my mac laptop and tunnelblick. When I connect in, I'm assigned an IP address of 10.8.0.x, the server is 10.8.0.1, so I have no problems SSHing into it. Once SSHd in, I can even ping other machines (obviously) on my home network (192.168.1.x). Desired outcome: What I want, is, to connect to the VPN server, and instead of getting a 10.8.0.x address, I get a 192.168.1.x on my home network. I can't figure out how to talk to the OTHER machines on my home network WITHOUT being SSHd in to the VPN server. I'd like to just connect to my VPN server, then be a part of my home network. Attempted solutions: I've read that I need to set up routes, and/or enable IP forwarding. I enabled IP forwarding using sudo sysctl -w net.ipv4.ip_forward=1 and that doesn't seem to have done anything. I've also uncommented a line in the OpenVPN's server.conf file: # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. push "route 192.168.1.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" But still no luck, I still get a 10.8.0.x address... I've also read I may have to add routes to the router itself, but haven't tried that. Any help appreciated, thanks!

  Read the article

• PPPD Is Locking the Modem and Not Releasing It

  - by Skid

  Got an issue with PPPD on one of our system, we have a PC that is used to talk to remote sites via a dial up connection, the modem can both connect out to the sites and the sites also dial back in. Currently I'm having an issue where some times a site ether dials in or we dial out, and it connects, but then blocks the modem and throws and error to kern.log. Aug 26 14:23:57 TM-SCADA kernel: [191233.503745] INFO: task pppd:8142 blocked for more than 120 seconds. Aug 26 14:23:57 TM-SCADA kernel: [191233.503750] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 26 14:23:57 TM-SCADA kernel: [191233.503753] pppd D ffffffff8180cb40 0 8142 1 0x00000000 Aug 26 14:23:57 TM-SCADA kernel: [191233.503759] ffff8800ac1f5dc8 0000000000000086 ffff8800ac1f5fd8 00000000000137c0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503765] ffff8800ac1f4010 00000000000137c0 00000000000137c0 00000000000137c0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503770] ffff8800ac1f5fd8 00000000000137c0 ffffffff81c13020 ffff880135df5b80 Aug 26 14:23:57 TM-SCADA kernel: [191233.503775] Call Trace: Aug 26 14:23:57 TM-SCADA kernel: [191233.503784] [<ffffffff8166ba29>] schedule+0x29/0x70 Aug 26 14:23:57 TM-SCADA kernel: [191233.503790] [<ffffffff813db005>] tty_ldisc_ref_wait+0x65/0xb0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503796] [<ffffffff813f3061>] ? uart_ioctl+0xd1/0x1c0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503801] [<ffffffff81076960>] ? wake_up_bit+0x40/0x40 Aug 26 14:23:57 TM-SCADA kernel: [191233.503806] [<ffffffff813d3fa0>] tty_ioctl+0x2c0/0x9a0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503810] [<ffffffff811d0549>] ? fcntl_setlk+0x69/0x200 Aug 26 14:23:57 TM-SCADA kernel: [191233.503815] [<ffffffff81195f79>] do_vfs_ioctl+0x99/0x330 Aug 26 14:23:57 TM-SCADA kernel: [191233.503820] [<ffffffff81195212>] ? do_fcntl+0x232/0x410 Aug 26 14:23:57 TM-SCADA kernel: [191233.503823] [<ffffffff811962b1>] sys_ioctl+0xa1/0xb0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503829] [<ffffffff81674e69>] system_call_fastpath+0x16/0x1b The syslog trace stops at "Serial connection established". Aug 28 06:00:03 TM-SCADA pppd[10358]: pppd 2.4.5 started by root, uid 0 Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (NO CARRIER) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (NO DIALTONE) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (ERROR) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (NO ANSWER) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (BUSY) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (Username/Password Incorrect) Aug 28 06:00:04 TM-SCADA chat[10360]: send (atz^M) Aug 28 06:00:04 TM-SCADA chat[10360]: expect (OK) Aug 28 06:00:04 TM-SCADA chat[10360]: atz^M^M Aug 28 06:00:04 TM-SCADA chat[10360]: OK Aug 28 06:00:04 TM-SCADA chat[10360]: -- got it Aug 28 06:00:04 TM-SCADA chat[10360]: send (atx0^M) Aug 28 06:00:04 TM-SCADA chat[10360]: expect (OK) Aug 28 06:00:04 TM-SCADA chat[10360]: ^M Aug 28 06:00:04 TM-SCADA chat[10360]: atx0^M^M Aug 28 06:00:04 TM-SCADA chat[10360]: OK Aug 28 06:00:04 TM-SCADA chat[10360]: -- got it Aug 28 06:00:04 TM-SCADA chat[10360]: send (atdt0123456789^M) Aug 28 06:00:04 TM-SCADA chat[10360]: expect (CONNECT/ARQ) Aug 28 06:00:04 TM-SCADA chat[10360]: ^M Aug 28 06:00:30 TM-SCADA chat[10360]: atdt0123456789^M^M Aug 28 06:00:30 TM-SCADA chat[10360]: CONNECT/ARQ Aug 28 06:00:30 TM-SCADA chat[10360]: -- got it Aug 28 06:00:30 TM-SCADA pppd[10358]: Serial connection established. I've only found two ways to release the modem in this condition, the first is to turn the modem off and on again, the second is to delete the serial lock file, and then SIGKILL pppd. Now I could write into our software to do the latter if the modem is locked, but I would rather stop it from locking in the first place if at all possible. The reason I put this issue in the askubuntu is because we used to use OpenSuse and never had an issue with it, admittedly that was version 11.2 or earlier so its still and old kernel, but I figured I would ask here first anyway. Any suggestions of places to look would be appreciated.

  Read the article

• Bridged VM guest does not get IPv6 prefix

  - by Arne

  I have a similar problem and setup as described in IPv6 does not work over bridge. My host get a IPv6 prefix but the guest VM only gets a local fe80-prefix. Using tcpdump I can see that solicit messages are going out from the guest but the host (ubuntu-server) doesn't seem to respond: arne@ubuntu-server:/var/log$ sudo tcpdump -i br0 host fe80::5054:00ff:fe4d:9ae0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on br0, link-type EN10MB (Ethernet), capture size 65535 bytes 14:31:15.314419 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 4 group record(s), length 88 14:31:15.322337 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28 14:31:15.502374 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28 14:31:15.743894 IP6 fe80::5054:ff:fe4d:9ae0.dhcpv6-client > ff02::1:2.dhcpv6-server: dhcp6 solicit 14:31:15.802389 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 4 group record(s), length 88 14:31:17.906580 IP6 fe80::5054:ff:fe4d:9ae0.dhcpv6-client > ff02::1:2.dhcpv6-server: dhcp6 solicit I had a firewall issue which I fixed by adding the following (copied from similar IPv4 before.rules settings) to /etc/ufw/before6.rules at the end before the commit statement: # allow bridging (for KVM) -I FORWARD -m physdev --physdev-is-bridged -j ACCEPT I am running the host on a Ubuntu 14.04 server so I guess I could have used dnsmasq but I didn't find any howto for it so I used radvd (which had to be installed) with the following configuration in /etc/radvd.conf: interface br0 { AdvSendAdvert on; AdvLinkMTU 1480; prefix 2a01:79d:xxx::/64 { AdvOnLink on; AdvAutonomous on; }; }; This didn't help though so I guess I must have configured it wrong? Any help appreciated. Br, Arne PS: I wish the Ubuntu documentation included how to configure virtualization to work with IPv6

  Read the article

• Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. My network setup: Telenet ISP (Belgium) Fiber cable < RJ45 cable straight to Ubuntu PC Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ nmap 192.168.0.128 Starting Nmap 5.50 ( http://nmap.org ) at 2012-06-08 19:11 CEST Nmap scan report for 192.168.0.128 Host is up (0.00045s latency). All 1000 scanned ports on 192.168.0.128 are closed (842) or filtered (158) Nmap done: 1 IP address (1 host up) scanned in 6.86 seconds ubuntu@ubuntu:~$ netstat -aunt | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 1 192.168.0.128:58616 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:56749 199.7.57.72:80 ESTABLISHED tcp 0 1 192.168.0.128:58614 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:49916 173.194.65.113:443 ESTABLISHED tcp 0 1 192.168.0.128:45699 64.34.119.101:80 SYN_SENT tcp 0 0 192.168.0.128:48404 64.34.119.12:80 ESTABLISHED tcp 0 0 192.168.0.128:54161 67.201.31.70:80 TIME_WAIT $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 $ apt-get install openipml openhpi-plugin-ipml $ openipmish > help redisp_cmd on|off > redisp_cmd on redisp set Final follow up: Step 1: BUG for network card driver r8169 Step 2: get the latest build version http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=4&PFid=4&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true#RTL8110SC(L) Step 3: build / make $ cd /var/tmp/driver $ tar xvfj r8169.tar.bz2 $ make clean modules && make install $ rmmod r8169 $ depmod $ cp src/r8169.ko /lib/modules/3.xxxx/kernel/drivers/net/r8169.ko $ modprobe r8169 $ update-initramfs -u $ init 6 Voila!!

  Read the article

• Could anyone help me get my NETGEAR WNA3100 (Broadcom BCM43231) wireless adapter to work?

  - by Matthew Carroll

  I have just moved back to Ubuntu from Windows 7 and a few months ago, I bought a NETGEAR WNA3100 wireless adapter because my old adapter had broken. I plugged in my adapter and it doesn't seem to work, I also used the windows 7 drivers for it and tried them on the program "Windows Wireless Drivers" and they don't seem to recognize the device. However I have heard you need XP drivers but I can't seem to find them on the internet nor find them on the CD. Could anyone help me get my wireless adapter to work? Any help is greatly appreciate. P.S I do have internet connection though I have to tether my phone to my computer and then connect my phone to my router.

  Read the article

• High number of ethernet errors. Tool for testing the ethernet card?

  - by Fabio Dalla Libera

  I have an Asus Sabertooth X79. I often get corrupted files. I checked the RAM, but memtest finds no errors. To avoid the possibility of disk errors, I tried copying the files to tmpfs. If I copy from the network, I get md5sum mismatches about once every 10 times using a 6Gb file. Copying from RAM to RAM, I didn't get mismatches. I get a very high number of errors in ifconfig (compared to others PCs I just took as reference, which have 0 with much more traffic). Here is an example RX packets:13972848 errors:200 dropped:0 overruns:0 frame:101 The motherboard is new, but do you think there're some problems with it? What could I use to test the (integrated) network adapter? What else do you think I should double check? --edit-- I tried another NIC, it gives a lot of Corrupted MAC on Input. Disconnecting: Packet corrupt lost connection. I noticed that another PC downloads at 11.1MB/s without problems. This pc at 66.0 MB/s. Is there any way to try to limit the speed?

  Read the article

• Internet problems

  - by user288636

  I have a strange problem. When I copy/paste via ethernet everything is working fine. But when I go to youtube or downloading some files via internet, connection is freezing very often. Just stop downloading and after few minutes continue and than again stop and etc... Could it be hardware problem with network card or motherboard (network is integrated on board)? I am using Ubuntu 14.04 but it happens on live cd distribution of Mint. There is no restrictions cose when I using on same switch my other laptop with linux installed everything working fine.

  Read the article

• Good alternative to NetLimiter(windows) for ubuntu

  - by Harsh

  there is program NetLimiter for windows. while I was using windows it was very useful to me to find out the IP address of ther person who was downloading from me, or to know IP address of any person on lan who was using DC++ with some nick. and after that I can easily know the computer name of that person using nbtstat. I was wondering if there is any tool for ubuntu using which I an find out the IP address of person who is downloading from me or from whom I am downloading on lan. I am on university lan and we are using PtokaX and DC++ for file sharing on lan. people sometimes put some offencive stuff on open chat on DC++ using some Nick and I don't know how to trace them while I am using Ubuntu. Plz help.

  Read the article

• Network Balancing Act

  - by listey

  Next up in our popular Oracle Solaris How To series is the Integrated Load Balancer, part of the suite of network facilities that are built in to Oracle Solaris 11. Providing Layer 3 and Layer 4 load balancing capabilities you can use this device to simulate or even replace your hardware based network infrastructure. Read more about the capabilities and how to get a basic configuration working in How to Set Up a Load-Balanced Application Across Two Oracle Solaris Zones

  Read the article

• Huawei E3276 LTE uplink slow in the routing Ubuntu, but not with other devices in the LAN

  - by Mytomi

  I have a Huawei E3276 LTE dongle (12d1:14fe - 12d1:1506) and a problem with the upstream speed. The problem is not only present with Ubuntu 14.04 LTS (64 bit workstation, kernel 3.16), but also with Raspbian Jessie for Raspberry PI (kernel 3.14). Upstream seems to be always limited to 5 Mbit/s whenever I check the speed from the Linux computer that I use as a LTE router. The other computers in the LAN always get about 10-15 Mbit/s upstream, even though the traffic is routed through the same Linux computer suffering from seemingly capped uplink. Downstream speed is always fine, 25 Mbit/s. I even installed Windows 7 in the same computer as Ubuntu and the speeds are 25 Mbit/s down, 15 Mbit/s up. So the problem is not with E3276 device itself or in the mobile subscription, but in the Huawei E3276 Linux compatibility. Maybe something in the kernel? I have made sure that the matter is not with iptables rules: the speed does not noticeably increase when iptables is disabled. Turning off IPv4 forwarding does not improve speed either. I'm not sure what settings and logs do help in debugging the situation. Please ask for more details, if you have a clue what might be wrong. Thanks, Mytomi

  Read the article

• Is it possible to write a program that pipes the sound from one computer through the sound card of another?

  - by Kenneth

  I have a case where I need to use one computer's sound card to play sound but I want the sound to be generated at another computer that's on the same network as the other. Ideally the program that does this would only run on the computer that was generating the sound, though I'm fairly certain that isn't possible based on the research I have been doing. What ever I do with it though the solution would need to be such that the computer actually playing the sound would be secure. Thanks for any input.

  Read the article

• Setting up shared connection

  - by Calvin Froedge

  I have a network that is connected to the internet via a switch connected to a router. I have it setup like this so I can work on the new network without causing problems on the old. Anyway, I'm trying to enable internet connection sharing. Internet comes to server like this: Modem - Router - Switch - Ubuntu 11.10 (Eth0) I want to share the connection through Eth1 (Eth1 - Managed Switch - Clients). Here is my config for /etc/network/interfaces: I have a DHCP server running on Eth1. Here is my config: ddns-update-style none; option domain-name "myserver.local"; option domain-name-servers 192.168.1.2, 8.8.8.8; default-lease-time 600; max-lease-time 7200; authoritative; subnet 192.168.1.0 netmask 255.255.255.0 { interface eth1; range 192.168.1.3 192.168.1.254; option routers 192.168.1.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.1.255; } Here is /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp #Used for internal network auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 Here is /etc/hosts: 127.0.0.1 localhost 127.0.1.1 myserver.isp.com server 192.168.1.2 server.myserver.local server myserver.local In /etc/sysctl.conf, I've set the following: net.ipv4.ip_forward=1 Finally, in /etc/rc.local, I've set the following: /sbin/iptables -P FORWARD ACCEPT /sbin/iptables --table nat -A POSTROUTING -o eth1 -j MASQUERADE When I ping 8.8.8.8 (google's DNS) from a client that is authenticated with my DHCP server (they have been assigned a local ip, like 192.168.1.10), I get a timeout. How can I debug this further to figure out where my problem is?

  Read the article

• Wireless not detected on an hp Pavilion g6 - RT5390PCIe

  - by Earl Larson

  I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

  Read the article

• How to connect to DSL modem using PPPoE?

  - by VJo

  Hello, I am connecting to the internet through a pppoe connection, but for some reason I can not connect to my modem (it's address is 192.168.1.1). Before I set my pppoe connection, I could connect. So, is there a way? EDIT The output of ifconfig is : r@PlaviZec:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:13:d4:f7:02:d4 inet6 addr: fe80::213:d4ff:fef7:2d4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2811 errors:0 dropped:0 overruns:0 frame:0 TX packets:2801 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2538831 (2.5 MB) TX bytes:448591 (448.5 KB) Interrupt:21 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:28 errors:0 dropped:0 overruns:0 frame:0 TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1600 (1.6 KB) TX bytes:1600 (1.6 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:92.229.42.177 P-t-P:213.191.64.59 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:2794 errors:0 dropped:0 overruns:0 frame:0 TX packets:2741 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:2476277 (2.4 MB) TX bytes:381240 (381.2 KB)

  Read the article

• Ethernet card not detected on Ubuntu Server 12.04

  - by Dana

  My onboard ethernet isn't detected after a re-install of Server 12.04. For reasons I won't get into here, I had to put the server's drive into another machine to install Ubuntu, then swap back into the server. So the server starts up fine, except for the "Waiting for network configuration". I read in another article that Server, by default, doesn't handle new mac addresses for hardware changes dynamically, unlike Ubuntu Desktop, but a look at /etc/udev/rules.d/70-persistent-net.rules shows only one ethernet interface. Shouldn't it show both the old, and the new? lspci -vv shows an ethernet interface, so what the heck is going on? I should mention that the onboard LAN is enabled in the BIOS. And I know this isn't important, but all this started when I changed some network configuration settings in webmin before the re-install. It couldn't download any updates, so I tinkered a little. Broke, it, installed FreeNAS, which worked, but I didn't like it, then went back to Ubuntu Server, and now I'm in this pickle. Thanks for any advice!

  Read the article

• How to prevent a hacked-server from spoofing a master server?

  - by Cody Smith

  I wish to setup a room-based multilayer game model where players may host matches and serve as host (IE the server with authoritative power). I wish to host a master server which tracks player's items, rank, cash, exp, etc. In such a model, how can I prevent someone that is hosting a game (with a modified server) from spoofing the master server with invalid match results, thus gaining exp, money or rankings. Thanks. -Cody

  Read the article

• Only 192.168.0.3 can request, but anyone can request /public/file.html

  - by mattalexx

  I have the following virtual host on my development server: <VirtualHost *:80> ServerName example.com DocumentRoot /srv/web/example.com/pub <Directory /srv/web/example.com/pub> Order Deny,Allow Deny from all Allow from 192.168.0.3 </Directory> </VirtualHost> The Allow from 192.168.0.3 part is to only allow requests from my workstation machine. I want to tweak this to allow anyone to request a certain URL: http://example.com/public/file.html How do I change this to allow /public/file.html requests to get through from anyone? Note: /public/file.html doesn't actually exist as a file on the server. I redirect all incoming requests through a single index file using mod_rewrite.

  Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >