Search Results

Search found 11126 results on 446 pages for 'hardware requirements'.

Page 411/446 | < Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >

• How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7?

  - by Timo

  The question says it all, but more detail follows ;) I've got a new computer that runs Windows 7 64-bits (Home Edition) and I'd like to connect it to my wireless home network (Sitecom wireless gigabit router 300N wl-352 v1 002) with a Sitecom wireless USB micro adaptapter 300 wl-352 V2 001. After installing the router (i.e. connected to the modem and power) and ensuring that wireless is indeed enabled, I've installed the driver of the USB adapter on the new computer described above. After the installation (drivers and utility on CD) completes successfull I rebooted my computer and inserted the USB adapter. After discovering the right network and connecting to it using the network key, a connection is succesfully made. (Using the Sitecom 300N USB Wireless LAN utility). In the LAN utility I can see that the signal strength is approximately 50% and connection quality is approximately 80%. Judging from these numbers I assumed that all was fine and started to use the connection (reading news on nu.nl, a dutch news site), but noticed that the connection was lost several times in a very short time span, but each time the connections was resumed, resulting in the 50/80 percent numbers described above. However, the website was not loaded completely and often a timeout would be reported. When inspecting the drivers through Device Management (Windows' Apparaatbeheer in dutch) there were no errors/warnings; everything seemed to be in order. In an attempt to solve this, I downloaded the latest drivers for the USB adapter, but the problems remained. Finally I tried to connect the computer with a Siemens Gigaset USB Adapter 108. This process was a troublesome since I had to download a driver (from the site above) and tell Windows (7) to use the Windows Vista driver when installing the new hardware, since there is (was) no Windows 7 driver available. This resulted in a usable connection, although not very stable when reconfiguring the router. Which took the form of selecting a different wireless channel on the router, even using the Sitecom utility mentioned above to check if there were other networks communicating on that channel (and thus picking a channel that was not used by other networks). Again no result when changing back to the Sitecom USB adapter. Note that this means (I think) that I could use the internet connection with the Siemens adapter, meaning the problem was not in the router. So: How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7? PS Sorry, but should be able to post one link, while I had links in place for the USB adapter, router and the siemens adapter in place as well, but I'm not (yet) allowed to post these... (The site says I can post one link, but only when no links are present will it allow me to post the question...)

  Read the article

• Open-source and client-side IRC-Client

  - by user125197

  I'm administrating a homepage with an IRC-Webclient. At the moment, it uses a Java-client, modified to be SSL-compatible and compatible with whatever design I want to use. The usual PJIRC thing, with users wishes and concerns implemented (I'll give you SSL-PJIRC if you want - no problem. The login-script will be improved for IE6-support this weekend, means write the object tag if an old IE is found, that's it. Rest runs perfectly well). But still, the better user experience would be a client that only requires the user to enable JavaScript. So, before I go into rewriting and customizing a complete Java-IRC-solution, I'd like to ask some other people - after researching for half a year of time. The requirements are: a) Free hosting, no cgi-bin is acceptable. A lot of hosters also have CGI supported, but it doesn't allow IRC-access. So, seems you are limited to x10-hosting for CGI:IRC. b) Solution must be open source (not free as in free beer, but free as in free speech - I want to be able to read every line of the code). c) Hosting cannot be limited to Windows-hosting. Free operation systems (anything with Linux, BSD, whatever - I think you get what I mean) must be possible. d) No server-side technology. I'm limited to everything that runs client-side only. (Well, a Java-Applet does...). d) Solution must support SSL. e) The side must be able to move. Means, you register to a new free hoster, load your things up via FileZilla and the thing simply runs. No server-concerning implementations needed. f) Old browsers must be supported. From all my research, there are two ways a) Java-Applet b) Use HTML5-Websockets (it is impossible to use the JavaScript-library I found, as it depends on ActiveX - means, Windows hosting). b) means "you are going to enter very unstable content". I worked with HTML5 for month, and, well ... Though, HTML5 also is not suitable for older browsers (old browser support is an absolutely necessary requirement). PHP by the way is a server side solution ... so no line of PHP. My idea now was a Java Applet, and a fallback which again is embedded and proprietary, but only requieres JavaScript (wsirc or Mibbit are great here, whilst I prefer wsirc ... and zooming fonts that are plainly to small, but worse, cannot read the code). So my question is - with free hosting, not installation on server, plain upload - do you see and open source, complelety client-side, ssl-compatible way to use or write a client? This wouldn't be my first programming project, I'm not afraid of the code. If there was a way and I had to write it, even from scratch, I'd do. From all I know, there sadly is none. But maybe some experienced admin has an idea? Best Wishes, yetanotheruser Sry my English isn't perfect. It's enough for programming at least.

  Read the article

• EMC/Legato/Networker Failed to recover files : Cross Platform Recovery not supported.

  - by marc.riera

  Software used to backup: EMC / Legato Networker legato server : windows legato clients: same hardware (2 years ago fedora something , now ubuntu ) Trying to recover from an old client, which is no longer available. So this is the thing. On 07/20/2008 we backed up a samba server(fedora something) to a tape , setting 1 year as browse policy and retention policy. Now this tape is recyclable. We took down the dns name. We deleted the legato client configuration. That legato client was reinstalled and is doing other stuff on ubuntu 10.04, with a different name but same ip. Now, 2 years and some month later #### Now we need to recover a folder from 2008 backup, on the fedora-samba-server. First thing, legato does not show the client name because the config was deleted. We create it again. We just set the old dns back on track, pointing the same ip, where the old server was, same MAC address ;). We created a new 'old client configuration' pointing to the new server. (different legato ip for client "I suppose" ) The ssid where the needed folder is on 2 tapes, 20 and 22. The index for that backup is on tape 21. We put this tapes on the jukebox (IBMT4000) -- not important for the issue -- All three tapes expired its browsable and recoverable time. So they are on recyclable. We get the clone id from the ssid with following command: mminfo -avot -q "ssid=<ssid>" -r cloneid We set the tapes to notrecyclable nsrmm -S <ssid>/<cloneid> -o notrecyclable We change the retention for the tapes for a future date nsrmm -S <ssid> -e 01/20/2011 We check the dates are correct : mminf -avV -q "ssid=<ssid>" -r ssbrowse(26),ssretent(26),savetime So far its OK. We close the terminal. Restart the server, just for being sure. Finally, we recover the index for that ssid where the folder should be. nsrck -L7 -t "07/20/2008" oldservername.domain.org There, we open the Networker User, select the server, select the old client as source, select the new client as destination. And this is what I get. imgur image of output -- http://i.imgur.com/1nOr8.png Should I understand that I need to install whatsoever operating system that was running on the old "linux server"/"networker client" to be able to restore 26Mb of files? thanks

  Read the article

• Should use EXT4 or XFS to be able to 'sync'/backup to S3?

  - by Rafa

  It's my first message here, so bear with me... (I have already checked quite a few of the "Related Questions" suggested by the editor) Here's the setup, a brand new dedicated server (8GB RAM, some 140+ GB disk, Raid 1 via HW controller, 15000 RPM) it's a production web server (with MySQL in it, too, not just serving web requests); not a personal desktop computer or similar. Ubuntu Server 64bit 10.04 LTS We have an Amazon EC2+EBS setup with the EBS volume formatted as XFS for easily taking snapshots to S3, via AWS' console. We are now migrating to the dedicated server and I want to be able to backup our data to Amazon's S3. The main reason being the possibility of using the latest snapshot from an EC2 instance in case of hardware failure on the dedicated server. There are two approaches I am thinking of: do a "simple" file-based backup with rsync, dumping the database' and other files, and uploading to amazon via S3 API commands, or to an EC2 instance, or something. do a file-system "freeze" (using XFS) with the usual ebs/ec2 snapshot tool to take part of the file system, take a snapshot, and upload it to Amazon. Here's my question (or series of questions): Can I safely use XFS for the whole system as the main and only format on the dedicated server? If not, is it safe to use EXT4? Or should I use something else? would then be possible to make snapshots of the system to upload to Amazon? Is it possible/feasible/practical to do what I want to do, anyway? any recommendations? When searching around for S3/EBS/XFS, anything relevant to my problem is usually focused on taking snapshots of a XFS system that is already an EBS volume. My intention is to do it in a "real"/metal dedicated server. Update: I just saw this on Wikipedia: XFS does not provide direct support for snapshots, as it expects the snapshot process to be implemented by the volume manager. I had always assumed that I could choose 2 ways of doing snapshots: via LVM or via XFS (without LVM). After reading this, I realize these 2 options are more like it: With XFS: 1) do xfs_freeze; 2) copy the frozen files via, eg, rsync; 3) unfreeze xfs With LVM and XFS: 1) do xfs_freeze; 2) make a binary copy of the frozen fs via lvcreate and related commands; 3) unfreeze xfs; 4) somehow backup the LVM snapshot. Thanks a lot in advance, Let me know if I need to clarify something.

  Read the article

• What is the best server or Ip address to use for prolonged testing?

  - by eldorel

  I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• Some services refusing to start on Win 7 machine. What could the root cause be?

  - by BombDefused

  When I check msconfig, there are no services that are blocked from starting up. When I look in services.msc, the problem services have a start up type of 'Automatic', but have a blank space where others will show 'Started'. Attempting to start them manually results in the following pop up error messages. I have no idea what's causing this, looks like some sort of cascade effect from another problem service. It's affecting scheduled tasks, SQL server agent and windows back up services. How can I resolve this? I don't know how to work out what the root cause is. Task Scheduler Service Start Error: "Windows could not start the Task Scheduler service on local computer. 1068: The dependecy service or group failed to start. SQL Server Service Start Error: "The SQL Server Agent service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs." UPDATE: I've just noticed some other services have a description of "Failed to Read Description. Error Code: 2" They are: NetMsmqActivator, NetPipeActivator, NetTcpActivator, NetTcpPortSharing UPDATE 2: As joeqwerty says the Event Log service does seem to be the root of the problem. This service will not start either. It fails with 'Error 31 - A device attached to the system is not functioning correctly'. I've tried detaching all devices. I've also followed the advice here, where the same problem is described, but with no luck: http://social.technet.microsoft.com/Forums/en/w7itprosecurity/thread/44479c49-55e6-4bd7-b25e-3f2a6497306e Update 3 @ Pacey - The following was a good tip, really clear instruction. However, I found that those reg keys do not exist on my system. "Your Problem might also derive from the UpperFilter or LowerFilter Settings of the CDROM Drive. These are a known cause for Errorcode 31. You can find step-by-step instructions on removing the filters on about.com" I followed the advice through to checking every component in device manager separately, but everything is reported as working correctly!? These services did all work at one point. The hardware set up hasn't changed much. Guess I'm looking at a repair install maybe???!

  Read the article

• Bluetooth not detecting any devices in Windows 7

  - by underDog

  My Lenovo ThinkPad E320 Laptop running Windows 7 64bit has recently been refusing to detect any Bluetooth devices. I have tried to connect, using 'Add devices' under 'devices and printers' to two different Bluetooth mice and my HTC Wildfire android (2.2.1) phone and none of them are detected in the 'Add a device' dialog. History - Bluetooth initially seemed OK when I first got this laptop. I was able to connect to and use my android phone as a remote with no issues. I got my first Bluetooth mouse, it paired, but after each restart, or even after sleeping, it would not 're-connect' (even though it was listed under Bluetooth devices and supposedly 'working'), and I would need to remove the device and add it again. A week or two ago it stopped working all together. It is not detected at all. I gave up on the mouse and bought another (Lenovo ThinkPad brand) only to find that it was not detected either. I subsequently tested my Android phone and discovered it would not detect either. One thing of note is under 'Devices and Printers' there is listed a 'HID Keyboard Device' which under properties is listed as a 'Bluetooth HID Device'. This was not previously there before this problem started. Each time I remove it, or uninstall it from Device Manager it will quickly re-install itself, even with all my Bluetooth devices switched off. My (Google and searching this site) research of this issue has not yielded any definitive answers. I have changed the setting under Device Manager - Bluetooth - Properties - Power Management - 'Allow the computer to turn off this device to save power' to off. I have attempted to un-install and re-install the Bluetooth hardware, including the 'remove drivers' option and downloading and running the Lenovo Bluetooth installer package (found @ http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014997). Bluetooth is turned on. All items under Bluetooth properties (Discovery and Connections) are checked. I have tried changing the batteries. I'm not sure what else I can try, apart from perhaps doing a fresh install of Windows. Any suggestions?

  Read the article

• SQL Clustering on Hyper V - is a cluster within a cluster a benefit.

  - by Chris W

  This is a re-hash of a question I asked a while back - after a consultant has come in firing ideas in to other teams in the department the whole issue has been raised again hence I'm looking for more detailed answers. We're intending to set-up a multi-instance SQL Cluster across a number of physical blades which will run a variety of different systems across each SQL instance. In general use there will be one virtual SQL instance running on each VM host. Again, in general operation each VM host will run on a dedicated underlying blade. The set-up should give us lots of flexibility for maintenance of any individual VM or underlying blade with all the SQL instances able to fail over as required. My original plan had been to do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Within the VMs - create a failover cluster and then install SQL Server clustering. The consultant has suggested that we instead do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Create a cluster on the HOST machines which will host all the VMs. Within the VMs - create a failover cluster and then install SQL Server clustering. The big difference is the addition of step 4 whereby we cluster all of the guest VMs as well. The argument is that it improves maintenance further since we have no ties at all between the SQL cluster and physical hardware. We can in theory live migrate the guest VMs around the hosts without affecting the SQL cluster at all so we for routine maintenance physical blades we move the SQL cluster around without interruption and without needing to failover. It sounds like a nice idea but I've not come across anything on the internet where people say they've done this and it works OK. Can I actually do the live migrations of the guests without the SQL Cluster hosted within them getting upset? Does anyone have any experience of this set up, good or bad? Are there some pros and cons that I've not considered? I appreciate that mirroring is also a valuable option to consider - in this case we're favouring clustering since it will do the whole of each instance and we have a good number of databases. Some DBs are for lumbering 3rd party systems that may not even work kindly with mirroring (and my understanding of clustering is that fail overs are completely transparent to the clients). Thanks.

  Read the article

• Broadcom HT1100 SATA controller not working properly with 1TB drives

  - by Jeff C

  I've been using RHEL distro's for several years and always managed to find the answers until now. I know this is more of a hardware issue, but I've been working on this for over a week and trust Linux and the IT community to help more then HP. I have CentOS 6.3 installed on an HP ProLiant DL145 G3 server with the BroadCom HT1100 IO controller and ServerWorks SATA Controller MMIO BIOS v3.0.0015.6 Firmware. This controller does not support large drives fully. Here's what I've tried and the results; Stock setup - Freezes on the ServerWorks POST screen. Can't even enter CMOS without disconnecting the drives. If I simply disconnect the SATA cables before it gets to the ServerWorks screen and reconnect afterwards I can boot from a CD, USB, PXE fine. However fiddling with cables at ever boot isn't practical. If I enter the BIOS config I can set it to not try booting the drives but leave the controller enabled. This lets me boot normally but the drives are not visible in the OS (live CDs or USB installed). I used method #2 to install and update CentOS. I have the /boot partition on a USB drive (everything else is on the SATA drives in software RAID1) hoping that would work around the issue but I get this Kernel panic - not syncing:Attempted to kill init! Pid: 1, comm: init Not tainted 2.6.32-279.9.1.el6.x86_6 #1 Call Trace: [<ffffffff814fd6ba>] ? panic+0xa0/0x168 [<ffffffff81070c22>] ? do_exit+0x862/0x870 [<ffffffff8117cdb5>] ? fput+0x25/0x30 [<ffffffff81070c88>] ? do_group_exit+0x58/0xd0 [<ffffffff81070d17>] ? sys_exit_group+0x17/0x20 [<ffffffff8100b0f2>] ? system_call_fastpath+0x16/0x1b panic occured, switching back to text console I'm sure it should be possible to talk to the drives without the BIOS boot check since the BIOS doesn't see them in method #2 either, their disconnected when it checks, but Linux sees them fine. If anyone could help figure out how I would greatly appreciate it! The other possible option I've come across is a complex firmware update. Tyan has a few boards on their website with the HT1100 and a ServerWorks v3.0.0015.7 update which says "adds support for TB drives" in the release notes. If someone could help me get the Tyan SATA firmware into the HP ROM file so I could just reflash that would also be very much appreciated. Thanks for any help you guys can offer!

  Read the article

• OpenVPN multiple servers on the same subnet, high availability

  - by andre

  Hey everyone. Let me start by saying that my Linux experience isn't super awesome but I can usually find my way around things easily. Over at work we have an OpenVPN setup that's been due for some improvement for a while now. The main server (tap mode) runs in our office, behind a rather slow DSL connection. The main problem is that, since I'm usually out of the office, every time I want to access something on the virtual network I have to go through that server to get anywhere else. We have two servers up on 100 Mbit connections that we use for development and production purposes, about 3 more servers in the office (one of them behind a different T1 line for VOIP) and about two dozen clients who use the network on a daily basis from various locations. We've had situations where network routing (outside of our control) would not allow people to reach our main OpenVPN server whilst the other locations were connectable. Also any time someone outside the office wants to fetch something from any of the servers (say, a 500 MB code repository), a whopping 20 KB/s download speed is just unacceptable these days (did I mention slow DSL? ok). We had to implement traffic shaping on this server since maxing out this connection was fairly trivial. I had the thought of running two (or more) OpenVPN servers in the network. These would have to have the same subnet though, as our application relies on virtual network's IP addresses for some of its core functionality. The clients would also preferably retain the same IP addresses but that's not vital. For simplicity, lets call the current server office and the second server I'm setting up, cloud. Call the server on the T1 phone. This proved to be rather complex because as soon as I connect to cloud, I cannot see office. Any routes to a server that would go through office also do not work while I'm connected to cloud (no ping, nothing) and vice-versa. There's no rules for iptables that would be blocking the traffic either. Recently I came across this article on linuxjournal but the solution they provide seems to only cover the use of two servers and somewhat outdated (can't even find much documentation, their wiki is offline). They also state that adding more servers would be a complex task. Ideally I would like to keep the existing server office running the virtual network and also run the OpenVPN daemon on the cloud and phone servers (100 Mbit and very reliable connection, respectively) so that we're on safe ground in case of a hardware failure, DSL failure, etc. So, in essence, I'm looking for a highly available OpenVPN solution (fix, patch, hack, tweak, whatever you want to call it) that will accept connections on multiple hosts (2 or more) whilst keeping the same IP address subnet regardless of the server to which you connect to. Thanks for reading and sorry for the long post, I hope it gets the point across :P

  Read the article

• XCP Project Kronos syslog error: "irq ... : nobody cared" on Dom0 host

  - by Vlad Fedin

  One of our production clusters driven by XCP suddenly went uresponsive. After restart and some investigation we found such logs in dom0 machine syslog: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659040] irq 339: nobody cared (try booting with the "irqpoll" option) Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659058] Pid: 0, comm: swapper/3 Tainted: G C O 3.2.0-24-generic #37-Ubuntu Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659060] Call Trace: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659062] <IRQ> [<ffffffff810db37d>] __report_bad_irq+0x3d/0xe0 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659071] [<ffffffff810db605>] note_interrupt+0x135/0x190 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659074] [<ffffffff810d8e69>] handle_irq_event_percpu+0xa9/0x220 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659078] [<ffffffff8130ff3b>] ? radix_tree_lookup+0xb/0x10 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659081] [<ffffffff810d9031>] handle_irq_event+0x51/0x80 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659084] [<ffffffff810dc187>] handle_edge_irq+0x87/0x140 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659089] [<ffffffff813a8829>] __xen_evtchn_do_upcall+0x199/0x250 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659092] [<ffffffff813aa96f>] xen_evtchn_do_upcall+0x2f/0x50 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659096] [<ffffffff81666d3e>] xen_do_hypervisor_callback+0x1e/0x30 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659097] <EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659104] [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659107] [<ffffffff8100a1d0>] ? xen_safe_halt+0x10/0x20 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659110] [<fff IRQ 339 in cat /proc/interrupts: 339: ... xen-pirq-msi-x eth0 where eth0 is hardware NIC. While host machine seems to hang, guest machines continue to work, so our tiny internal monitoring on one of the virtual hosts logged something like that: [2012-10-26 20:31:51] [OK......] 200 OK : 113159149 ns [2012-10-26 20:32:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 47763284432 ns ... [2012-10-26 20:34:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 46894835070 ns [2012-10-26 20:34:57] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 16821741955 ns ... [2012-10-26 20:38:18] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 20103298289 ns [2012-10-26 20:38:37] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 17895754943 ns Host and guest OS: Ubuntu 12.04 LTS, 05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: ASUSTeK Computer Inc. Device 8369 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e000 [size=32] Region 3: Memory at fe520000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e Any hints how to debug this?

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• GPU not powering on

  - by Lerp

  So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

  Read the article

• Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

  - by Janar

  I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

  Read the article

• Windows7 issue in mutli- tasking and memory

  - by Nitesh

  I seeming some problem in my windows OS recently, let me first say my system configuration. processor - Intel(R) Core(TM)2 Quad CPU Q8400 @ 2.66 GHz Installed memory (RAM) - 4.00 GB (3.00 GB usable) System type - 32 bit operating system I am using two OS in this system, first one is Windows7 and the other is centOS. Well, I am using this from a long time there was no problem , and all of a sudden since from couple weeks I am facing problems in my Windows7 OS. In windows7 i was nearing using multiple jobs almost every time i log in, there was no problem but now i don't no what happen I am not able to do multiple jobs at same time. For example- 1 I am now not able to listen to music in windows media player and view photo's. All of a sudden the system stops working and does not respond and then respond after 5mins and the music get played where it got stopped after 5 mins. 2 When i start browersing internet it hangs all of sudden and doesn't respond for 2 or 3 mins and gets loading. I mean it just happens for every operation i do in the system. Even now typing was also difficult, it gets hanged very frequently even though i am doing single task. I have never come across this kind of problem before. So the first thing i did was to see the useage of the processor and the memory. Well, i thick the useage of the processor was fine, for single task the useage was some where around 3 to 5%. Well, it was something weird i found in the memory, in spite of no task that i was running it was using somewhere around 34 to 41% of memory. So i opened the task manager and click on resource monitor in performance tab. And in the memory section of the monitoring tool i found the usage of my RAM, it was something like this. Hardware reserved - 1029 MB In Use - 1430 MB Modified - 49 MB Standby - 1566 MB free - 22 MB And i could also see Available 1588 MB Cached 1615 MB Total 3067 MB Installed 4096 MB well, this if all i could find out and i have no idea why my computer is acting so weird all of a sudden and the performance problem is growing day by day and i also don't know if there is problem in Bios, i have let it for default settings from long time. please help me and Thank you in advance for reading this and helping me.

  Read the article

• Ubuntu getting wrong hostname from DHCP

  - by sam

  When provisioning new Ubuntu Precise (12.04) servers, the hostname they're getting seems to be generated from the DNS search path, not a reverse lookup on the hostname. Take the following configuration BIND is configured with the hostname, and reverse name Normal zone $TTL 600 $ORIGIN srv.local.net. @ IN SOA ns0.local.net. hostmaster.local.net. ( 2014082101 10800 3600 604800 600 ) @ IN NS ns0.local.net. @ IN MX 5 mail.local.net. my-new-server IN A 10.32.2.30 And reverse @ IN SOA ns0.local.net. hostmaster.local.net. ( 2014082101 10800 3600 604800 600 ) @ IN NS ns0.local.net. $ORIGIN 32.10.in-addr.arpa. 30.2 IN PTR my-new-server.srv.local.net. Then DHCPD is configured to hand out static leases based on mac addresses like so subnet 10.32.2.0 netmask 255.255.254.0 { option subnet-mask 255.255.254.0; option routers 10.32.2.1; option domain-name-servers 10.32.2.1; option domain-name "util.of1.local.net of1.local.net srv.local.net"; site-option-space "pxelinux"; option pxelinux.magic f1:00:74:7e; if exists dhcp-parameter-request-list { option dhcp-parameter-request-list = concat(option dhcp-parameter-request-list,d0,d1,d2,d3); } group { option pxelinux.configfile "pxelinux.cfg/pxeboot"; host my-new-server { fixed-address my-new-server.srv.local.net; hardware ethernet aa:aa:aa:bb:bb:bb; } } } So the hostname should be my-new-server.srv.local.net, however when building a Ubuntu 12.04 node, the hostname ends up as my-new-server.util.of1.local.net When building Lucid (10.04) hosts, the hostname will be correct, it's only on Precise/12.04 nodes we have the problem. Doing a normal and reverse lookup on the host and IP returns the correct result Sams-MacBook-Pro:~ sam$ host my-new-server my-new-server.srv.local.net has address 10.32.2.30 Sams-MacBook-Pro:~ sam$ host my-new-server.srv.local.net my-new-server.srv.local.net has address 10.32.2.30 Sams-MacBook-Pro:~ sam$ host 10.32.2.30 30.2.32.10.in-addr.arpa domain name pointer my-new-server.srv.local.net. The contents of the hosts file is incorrect too 127.0.0.1 localhost 127.0.1.1 my-new-server.util.of1.local.net of1.local.net srv.local.net my-new-server So it looks like when it creates the hosts file, it puts the entire contents of the DNS search path into the local address so the FQDN according to the server is the short hostname as defined, then the first domain in the search path. Is there a way to get around this behaviour, or fix this so it gets the hostname correctly? It's picking up the first part of the hostname, then the rest is wrong.

  Read the article

• How to free up space on RHEL6 /boot safely?

  - by ams

  I am trying to do yum update on RHEL 6 box and I am getting this error message Transaction Check Error: installing package kernel-2.6.32-279.9.1.el6.x86_64 needs 10MB on the /boot filesystem installing package grub-1:0.97-77.el6.x86_64 needs 10MB on the /boot filesystem Error Summary ------------- Disk Requirements: At least 10MB more space needed on the /boot filesystem. My /boot has the following # ls -lah /boot total 74M dr-xr-xr-x. 5 root root 2.0K Jun 10 08:05 . drwxr-xr-x. 23 root root 4.0K Aug 27 03:08 .. -rw-r--r-- 1 root root 99K Apr 26 12:53 config-2.6.32-220.17.1.el6.x86_64 -rw-r--r-- 1 root root 99K Feb 10 2012 config-2.6.32-220.7.1.el6.x86_64 -rw-r--r--. 1 root root 99K Nov 9 2011 config-2.6.32-220.el6.x86_64 drwxr-xr-x. 3 root root 1.0K Mar 29 2012 efi drwxr-xr-x. 2 root root 1.0K Jun 10 07:53 grub -rw-r--r-- 1 root root 15M Jun 10 07:53 initramfs-2.6.32-220.17.1.el6.x86_64.img -rw-r--r-- 1 root root 15M Mar 29 2012 initramfs-2.6.32-220.7.1.el6.x86_64.img -rw-r--r--. 1 root root 15M Mar 29 2012 initramfs-2.6.32-220.el6.x86_64.img -rw------- 1 root root 3.4M Jun 10 08:06 initrd-2.6.32-220.17.1.el6.x86_64kdump.img -rw------- 1 root root 3.5M Jun 10 07:53 initrd-2.6.32-220.7.1.el6.x86_64kdump.img -rw------- 1 root root 3.4M Mar 29 2012 initrd-2.6.32-220.el6.x86_64kdump.img drwx------. 2 root root 12K Mar 29 2012 lost+found -rw-r--r-- 1 root root 168K Apr 26 12:55 symvers-2.6.32-220.17.1.el6.x86_64.gz -rw-r--r-- 1 root root 168K Feb 10 2012 symvers-2.6.32-220.7.1.el6.x86_64.gz -rw-r--r--. 1 root root 168K Nov 9 2011 symvers-2.6.32-220.el6.x86_64.gz -rw-r--r-- 1 root root 2.3M Apr 26 12:53 System.map-2.6.32-220.17.1.el6.x86_64 -rw-r--r-- 1 root root 2.3M Feb 10 2012 System.map-2.6.32-220.7.1.el6.x86_64 -rw-r--r--. 1 root root 2.3M Nov 9 2011 System.map-2.6.32-220.el6.x86_64 -rwxr-xr-x 1 root root 3.8M Apr 26 12:53 vmlinuz-2.6.32-220.17.1.el6.x86_64 -rw-r--r-- 1 root root 171 Apr 26 12:53 .vmlinuz-2.6.32-220.17.1.el6.x86_64.hmac -rwxr-xr-x 1 root root 3.8M Feb 10 2012 vmlinuz-2.6.32-220.7.1.el6.x86_64 -rw-r--r-- 1 root root 170 Feb 10 2012 .vmlinuz-2.6.32-220.7.1.el6.x86_64.hmac -rwxr-xr-x. 1 root root 3.8M Nov 9 2011 vmlinuz-2.6.32-220.el6.x86_64 -rw-r--r--. 1 root root 166 Nov 9 2011 .vmlinuz-2.6.32-220.el6.x86_64.hmac here is the disk usage on boot # du -h 13K ./lost+found 282K ./grub 247K ./efi/EFI/redhat 249K ./efi/EFI 251K ./efi 75M . Problem is that when I got this severer at my ISP I used their default image for RHEL 6 which only allocates 100MB for /boot clearly this is not enough. How can I get around this problem, is it safe to delete any of the above files some of them seem to be on the disk more than once? Is there some way of expand /boot without re-imaging the machine?

  Read the article

• Set up lnux box for hosting a-z [apache mysql php ssl]

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

  Read the article

• IPv6: Should I have private addresses?

  - by AlReece45

  Right now, we have a rack of servers. Every server right now has at least 2 IP addresses, one for the public interface, another for the private. The servers that have SSL websites on them have more IP addresses. We also have virtual servers, that are configured similarly. Private Network The private range is currently just used for backups and monitoring. Its a gigabit port, the interface usage does not usually get very high. There are other technologies we're considering using that would use this port: iSCSI (implementations usually recommends dedicating an interface to it, which would be yet another IP network), VPN to get access to the private range (something I'd rather avoid) dedicated database servers LDAP centralized configuration (like puppet) centralized logging We don't have any private addresses in our DNS records (only public addresses). For our servers to utilize the correct IP address for the right interface (and not hard code the IP address) probably requires setting up a private DNS server (So now we add 2 different dns entries to 2 different systems). Public Network Our public range has a variety of services include web, email, and ftp. There is a hardware firewall between our network and the "public" network. We have (relatively secure) method to instruct the firewall to open and close administrative access (web interfaces, ssh, etc) for our current IP address. With either solution discussed, the host-based firewalls will be configured as well. The public network currently runs at a dedicated 20Mbps link. There are a couple of legacy servers with fast-ethernet ports, but they are scheduled for decommissioning. All of the other production boxes have at least 2 Gigabit Ethernet ports. The more traffic-heavy servers have 4-6 available (none is using more than the 2 Gigabit ports right now). IPv6 I want to get an IPv6 prefix from our ISP. So at least every "server" has at least one IPv6 interface. We'll still need to keep the IPv4 addressees up and available for legacy clients (web servers and email at the very least). We have two IP networks right now. Adding the public IPv6 address would make it three. Just use IPv6? I'm thinking about just dumping the private IPv4 range and using the IPv6 range as the primary means of all communications. If an interface starts reaching its capacity, utilize the newly free interfaces to create a trunk. It has the advantage that if either the public or private traffic needs to exceed 1Gbps. The traffic for each interface is already analyzed on a regular basis to predict future bandwidth use. In the rare instances where bandwidth unexpected peaks: utilize QoS to ensure traffic (like our limited SSH access) is prioritized correctly so the problem can be corrected (if possible, our WAN is the bottleneck right now). It also has the advantage of not needing to make an entry for every private address. We may have private DNS (or just LDAP), but it'll be much more limited in scope with less entries to duplicate. Summary I'm trying to make this network as "simple" as possible. At the same time, I want to make sure its reliable, upgradeable, scalable, and (eventually) redundant. Having one IPv6 network, and a legacy IPv4 network seems to be the best solution to me. Regarding using assigned IPv6 addresses for both networks, sharing the available bandwidth on one (more trunked if needed): Are there any technical disadvantages (limitations, buffers, scalability)? Are there any other security considerations (asides from firewalls mentioned above) to consider? Are there regulations or other security requirements (like PCI-DSS) that this doesn't meet? Is there typical software for setting up a Linux network that doesn't have IPv6 support yet? (logging, ldap, puppet) Some other thing I didn't consider?

  Read the article

• Alienware m15x (older model) BSOD investigation

  - by Crishu

  A frined of mine asked me to help him with an Alienware m15x laptop that had a little service history. It was bought in june 2008, serviced in january 2009 for a random fps drop problem, Alienware returned it saying nothing was wrong. The laptop still had hiccups, but after juggling a few drivers and settings, the fps drops weren't as noticeable. Eventually it died in Sept. 2009. It would not boot up locking itself on a white/gray screen. (i think it was overheating .. clocking in 100 degrees Celsius). So back to Alienware it went. They replaced the GPU and all was fine. Up until these blue screens started showing up. One other thing that was updated was the HDD and a Windows 7 reinstall, in August. From then on it seems to have started its BSOD. Could this be the culprit? Why? 0_o The original Windows was Vista but it was upgraded with a digital download/purchase of Windows 7 Home Premium and activated after installing windows. No errors on the old HDD, just on the latest installation. LE:Due note that now the old HDD is used to see if issues re-occur. So please, I am in need of someone who can interpret these windows dump files: Minidump I may have come to some conflicting conclusions. So if someone can clarify each dump/date and the probable cause/error it had; and a final conclusion or solution, we would be very grateful. Also please consult report for other system info I omitted: same link,code: XRWIVLWG If I missed something or if you have any other questions I'll be happy to answer them. Thank you. Good day. Processor: Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz Network Adapter Properties: Broadcom NetLink (TM) Gigabit Ethernet Intel(R) Wireless WiFi Link 4965AGN Video Adapter Properties: Driver Description NVIDIA GeForce 8800M GTX Driver Date 19.08.2009 Driver Version 8.16.11.8681 Driver Provider NVIDIA INF File oem19.inf Hardware ID PCI\VEN_10DE&DEV_060C&SUBSYS_0770152D&REV_A2 Location Information @system32\DRIVERS\pci.sys,#65536;PCI bus %1, device %2, function %3;(1,0,0) PCI Device NVIDIA GeForce 8800M GTX [NoDB] BIOS String Version 62.92.34.0.8 Installed Drivers nvd3dum (8.16.11.8681), nvwgf2um, nvwgf2um Hard Dik Drive: Model ID ST9120823ASG (**older one 120gb**) Model ID WD32000BEKT (new 320gb with fresh OS)

  Read the article

• Spotlight Infinite Indexing issue (external data drive)

  - by Manca Weeks

  This is an external drive, formerly a boot drive which is now in use only to access music files (sibelius, audio, midi, live, logic etc.) without transferring the data into a new boot system, partly because of the issue I am about to describe, but mostly because the majority of the data is mainly there for archival purposes. The user is a composer and prominent musician and needs to be able to rehash the data at will. I have tried several things - here is a list: - make complete filesystem clone with antonio diaz's ddrescue - run Disk Warrior on copy, repair whatever errors occurred - wipe out all ACLs on entire drive - set all permissions to the same value - wide open 777 - remove any system data (applications, system files, including hidden files to the best of my knowledge) by selecting only non-system/app data and using Carbon Copy Cloner to put only the data of interest onto a newly formatted drive - transfer data to newly formatted drive folder by folder, resetting the spotlight index in between adding each to observe for issues (interesting here is that no issues occurred except for in Documents folder - when I transferred only the Documents folder to a newly formatted drive on its own - no trouble. It appears almost as thought it may not be the content but the quantity or specific combination of data that results in problems) - use DataRescue to transfer the data to yet another newly formatted drive to expose any missed hidden files Between each of the above steps I stopped Spotlight (search for anything beginning with md in Activity Monitor - All Processes and quitting it), deleted the .Spotlight-V100 directory from the affected drive. Restart Splotlight indexing by adding drive to Spotlight privacy list and removing it. In each case the same issue occurs - Spotlight begins indexing normally (or so it seems), then the index estimated time increases, usually to 4 hours remaining. This is where it gets stuck and continues to predict 4 hours remaining but never finishes. Sometimes I can't eject the drive and have to quit the md.. processes from Activity Monitor to be able to eject the drive without Force Eject. Once I disconnect the drive after the 4 hours remaining situation - if I reattach it, Spotlight forever estimates remaining time and never gets going again. So there it is. It is apparently not a filesystem issue, not a permissions issue and not tied to any particular piece of hardware or protocol (used USB and FW drives). I have tried this on several machines (3 to be precise) and in 10.5.8 and 10.6.5. Simply disabling Spotlight on this volume is not an option because the owner has no clue where things are as the data on the volume dates back to music projects and compositions from 2003 and before. He needs to be able to query for results. Anyone got any ideas? Thanks, M

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

< Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >