Search Results

Search found 10989 results on 440 pages for 'wpf commands'.

Page 413/440 | < Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• Detecting upload success/failure in a scripted command-line SFTP session?

  - by Will Martin

  I am writing a BASH shell script to upload all the files in a directory to a remote server and then delete them. It'll run every few hours via a CRON job. My complete script is below. The basic problem is that the part that's supposed to figure out whether the file uploaded successfully or not doesn't work. The SFTP command's exit status is always "0" regardless of whether the upload actually succeeded or not. How can I figure out whether a file uploaded correctly or not so that I can know whether to delete it or let it be? #!/bin/bash # First, save the folder path containing the files. FILES=/home/bob/theses/* # Initialize a blank variable to hold messages. MESSAGES="" ERRORS="" # These are for notifications of file totals. COUNT=0 ERRORCOUNT=0 # Loop through the files. for f in $FILES do # Get the base filename BASE=`basename $f` # Build the SFTP command. Note space in folder name. CMD='cd "Destination Folder"\n' CMD="${CMD}put ${f}\nquit\n" # Execute it. echo -e $CMD | sftp -oIdentityFile /home/bob/.ssh/id_rsa [email protected] # On success, make a note, then delete the local copy of the file. if [ $? == "0" ]; then MESSAGES="${MESSAGES}\tNew file: ${BASE}\n" (( COUNT=$COUNT+1 )) # Next line commented out for ease of testing #rm $f fi # On failure, add an error message. if [ $? != "0" ]; then ERRORS="${ERRORS}\tFailed to upload file ${BASE}\n" (( ERRORCOUNT=$ERRORCOUNT+1 )) fi done SUBJECT="New Theses" BODY="There were ${COUNT} files and ${ERRORCOUNT} errors in the latest batch.\n\n" if [ "$MESSAGES" != "" ]; then BODY="${BODY}New files:\n\n${MESSAGES}\n\n" fi if [ "$ERRORS" != "" ]; then BODY="${BODY}Problem files:\n\n${ERRORS}" fi # Send a notification. echo -e $BODY | mail -s $SUBJECT [email protected] Due to some operational considerations that make my head hurt, I cannot use SCP. The remote server is using WinSSHD on windows, and does not have EXEC privileges, so any SCP commands fail with the message "Exec request failed on channel 0". The uploading therefore has to be done via the interactive SFTP command.

  Read the article

• Static IPv6 address in Windows unused for outgoing connections

  - by Luc

  I'm running a Windows server and trying to get it to use a static IPv6 address for outgoing connections to other IPv6 hosts (such as Gmail). I need this because Gmail requires a ptr record, and I can't set one for random addresses. The static address is configured on the host, but it also has a temporary privacy address as well as a random address from the router it seems. By default Windows uses the privacy address; it seems this is the expected behavior (and it makes perfect sense for people/users that did not set a static address, but I did!). I've tried disabling the privacy address with: netsh int ipv6 set privacy disabled This indeed gets rid of the privacy address, but I still have the random address that the router assigned. To disable this, it was said I needed to disable "router discovery" using this command: net interface ipv6 set interface 14 routerdiscovery=disabled Upon doing this, all IPv6 connectivity is lost. If I do this while pinging Gmail, it will report "Destination host unreachable" as soon as I enter the command. In the static IPv6 configuration, I did configure the default gateway and prefix length, so I don't see why it's unable to connect. Probably has something to do with the lack of ARP in IPv6 and somehow being unable to resolve the router's MAC, but I wouldn't know how to fix this. Finally I've tried disabling the DHCPv6 lease with these commands: netsh interface ipv6 set interface "IDMZ Team" managedaddress=disabled netsh interface ipv6 set interface "IDMZ Team" otherstateful=disabled Which was to no avail; the host continues to obtain and use the router-assigned IPv6 address. The router is a FritzBox 7340, which shows me all the IPv4 and IPv6 addresses that the host (identified by MAC) utilizes, but I'm unable to change the assigned address. Maybe this could be done over the telnet interface of the router somehow, but again, I wouldn't know how to do this even if it's the way to go. In short, any of the following would probably solve my problem: Change Windows' source address selection behavior. Have Windows not get an address from the router and not generate a privacy address; Have the router hand out a static address and make Windows use that as source address. Recover connectivity after disabling router discovery on Windows. Alternatively I might use some (batch, perl, ...) script to throw away all IPv6 addresses except the desired one, but this feels rather hacky. If it's the only way (or less hacky than another hacky solution), it might be an option though. Thanks!

  Read the article

• Solaris10 x86 mirror. Making second disk booteable when failure

  - by Kani

  Did a mirror (RAID1) with Solaris 10 in x86. Everything OK. Now, I´m trying to make the second disk booteable, this is: from grub or in case of failure of disk1. I edited /boot/grub/menu.lst: #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris 10 9/10 s10x_u9wos_14a X86 findroot (rootfs1,0,a) kernel /platform/i86pc/multiboot module /platform/i86pc/boot_archive #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot -s module /boot/amd64/x86.miniroot-safe #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe #---------------------END BOOTADM-------------------- #Make second disk booteable!!!!!!! title alternate boot findroot (rootfs1,1,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe But is not working. In the BIOS, when I select "alternate boot" I get: Error 15: 15 file not found also, how to configure to GRUB to make the disk2 to boot in case of error in disk1? Additionally, I did (but not related to GRUB): eeprom altbootpath=/devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a Here is the output of some commands that may help you: /sbin/biosdev 0x80 /pci@0,0/pci108e,5352@1f,2/disk@0,0 0x81 /pci@0,0/pci108e,5352@1f,2/disk@1,0 ls -l /dev/dsk/c1t?d0s0 lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t0d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@0,0:a lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t1d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a more /boot/solaris/bootenv.rc setprop ata-dma-enabled '1' setprop atapi-cd-dma-enabled '0' setprop ttyb-rts-dtr-off 'false' setprop ttyb-ignore-cd 'true' setprop ttya-rts-dtr-off 'false' setprop ttya-ignore-cd 'true' setprop ttyb-mode '9600,8,n,1,-' setprop ttya-mode '9600,8,n,1,-' setprop lba-access-ok '1' setprop prealloc-chunk-size '0x2000' setprop bootpath '/pci@0,0/pci108e,5352@1f,2/disk@0,0:a' setprop keyboard-layout 'US-English' setprop console 'text' setprop altbootpath '/pci@0,0/pci108e,5352@1f,2/disk@1,0:a' cat /etc/vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - #/dev/dsk/c1t0d0s1 - - swap - no - /dev/md/dsk/d1 - - swap - no - /dev/md/dsk/d0 /dev/md/rdsk/d0 / ufs 1 no - /devices - /devices devfs - no - sharefs - /etc/dfs/sharetab sharefs - no - ctfs - /system/contract ctfs - no - objfs - /system/object objfs - no - swap - /tmp tmpfs - yes - df -h Filesystem size used avail capacity Mounted on /dev/md/dsk/d0 909G 11G 889G 2% / /devices 0K 0K 0K 0% /devices ctfs 0K 0K 0K 0% /system/contract proc 0K 0K 0K 0% /proc mnttab 0K 0K 0K 0% /etc/mnttab swap 14G 972K 14G 1% /etc/svc/volatile objfs 0K 0K 0K 0% /system/object sharefs 0K 0K 0K 0% /etc/dfs/sharetab /usr/lib/libc/libc_hwcap1.so.1 909G 11G 889G 2% /lib/libc.so.1 fd 0K 0K 0K 0% /dev/fd swap 14G 40K 14G 1% /tmp swap 14G 28K 14G 1% /var/run

  Read the article

• DNS and DHCP dies after ~2 days of use on ClearOS

  - by TheLQ

  I'm using ClearOS (based on CentOS, so any info specific to it should apply here) as a gateway, DHCP, and DNS server. I had this server running perfectly for a month or two before replacing it with another server. However due DNS and DHCP failing 2 days in and a host of other performance issues (the box was a little underpowered), I changed back to the origional server. However 2 days in DHCP and DNS are failing again, and I'm out of idea's on why. In both cases to my knowledge no network or server changes occurred after installation. Right after installing (and at least a day in) DNS and DHCP was working just fine. However later (Day 2) I get a call saying their internet is down (translation: Nobody can get to websites because DNS is down) I've tried to fix the problem by checking if the dnsmasq is even running (it is), restarting the service, and restarting the server to no effect. I do have two internal servers that have static DHCP leases but one's lease must of expired as I can't connect to it anymore. I'm hesitant to do any dhcp testing on the last server as I'll not be able to connect to it anymore. Is there anything anyone can think of on why DNS and DHCP would fail 2 days in to running perfectly? More info: Running dnsmasq in debug mode. This is all that's displayed even when running nslookup quackwall. I'm not sure though if nslookup commands should show up in the log [root@quackwall ~]# /usr/sbin/dnsmasq -dq dnsmasq: started, version 2.49 cachesize 150 dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP dnsmasq-dhcp: DHCP, IP range 10.0.0.100 -- 10.0.0.254, lease time 12h dnsmasq: reading /etc/resolv.conf dnsmasq: using nameserver 74.128.17.114#53 dnsmasq: using nameserver 74.128.19.102#53 dnsmasq: read /etc/hosts - 5 addresses dnsmasq-dhcp: read /etc/ethers - 2 addresses On the other server DNS and the Gateway are all configured correctly (10.0.0.2 is quackwall) lordquackstar@quackgame:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.240.0 U 0 0 0 eth0 0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0 lordquackstar@quackgame:~$ cat /etc/resolv.conf nameserver 10.0.0.2 domain highwow.lan search highwow.lan

  Read the article

• Slow Memcached: Average 10ms memcached `get`

  - by Chris W.

  We're using Newrelic to measure our Python/Django application performance. Newrelic is reporting that across our system "Memcached" is taking an average of 12ms to respond to commands. Drilling down into the top dozen or so web views (by # of requests) I can see that some Memcache get take up to 30ms; I can't find a single use of Memcache get that returns in less than 10ms. More details on the system architecture: Currently we have four application servers each of which has a memcached member. All four memcached members participate in a memcache cluster. We're running on a cloud hosting provider and all traffic is running across the "internal" network (via "internal" IPs) When I ping from one application server to another the responses are in ~0.5ms Isn't 10ms a slow response time for Memcached? As far as I understand if you think "Memcache is too slow" then "you're doing it wrong". So am I doing it wrong? Here's the output of the memcache-top command: memcache-top v0.7 (default port: 11211, color: on, refresh: 3 seconds) INSTANCE USAGE HIT % CONN TIME EVICT/s GETS/s SETS/s READ/s WRITE/s cache1:11211 37.1% 62.7% 10 5.3ms 0.0 73 9 3958 84.6K cache2:11211 42.4% 60.8% 11 4.4ms 0.0 46 12 3848 62.2K cache3:11211 37.5% 66.5% 12 4.2ms 0.0 75 17 6056 170.4K AVERAGE: 39.0% 63.3% 11 4.6ms 0.0 64 13 4620 105.7K TOTAL: 0.1GB/ 0.4GB 33 13.9ms 0.0 193 38 13.5K 317.2K (ctrl-c to quit.) ** Here is the output of the top command on one machine: ** (Roughly the same on all cluster machines. As you can see there is very low CPU utilization, because these machines only run memcache.) top - 21:48:56 up 1 day, 4:56, 1 user, load average: 0.01, 0.06, 0.05 Tasks: 70 total, 1 running, 69 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.3%st Mem: 501392k total, 424940k used, 76452k free, 66416k buffers Swap: 499996k total, 13064k used, 486932k free, 181168k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 6519 nobody 20 0 384m 74m 880 S 1.0 15.3 18:22.97 memcached 3 root 20 0 0 0 0 S 0.3 0.0 0:38.03 ksoftirqd/0 1 root 20 0 24332 1552 776 S 0.0 0.3 0:00.56 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 4 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kworker/0:0 5 root 20 0 0 0 0 S 0.0 0.0 0:00.02 kworker/u:0 6 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0.0 0.0 0:00.62 watchdog/0 8 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 cpuset 9 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 khelper ...output truncated...

  Read the article

• VMWare tools not installing with an error

  - by JDS

  VMWare tools not installing on Ubuntu 12.04. I'm using Chef to manage the installation, but the Apt commands fail if run manually. I'm using the VMWare tool Debian repo. Example: $ cat /etc/apt/sources.list.d/vmware-tools-source.list deb http://packages.vmware.com/tools/esx/5.0u2/ubuntu precise main When trying to install, most packages seem to go ok, but one, "vmware-tools-foundation", does not. Example: $ apt-get -q -y install vmware-tools-esx-nox=8.6.10-1.precise Reading package lists... Building dependency tree... Reading state information... You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: vmware-tools-esx-kmods-3.2.0-23-generic : Depends: vmware-tools-foundation (>= 8.6.10) but it is not going to be installed vmware-tools-esx-nox : Depends: ...snip list of deps... E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). $ apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: vmware-tools-foundation The following NEW packages will be installed: vmware-tools-foundation 0 upgraded, 1 newly installed, 0 to remove and 118 not upgraded. 7 not fully installed or removed. Need to get 0 B/5,886 B of archives. After this operation, 86.0 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 103499 files and directories currently installed.) Unpacking vmware-tools-foundation (from .../vmware-tools-foundation_8.6.10-1.precise_all.deb) ... VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again. dpkg: error processing /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) The key seems to be this error: "VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again." However, I've tryed removing and purging and can't seem to "trick" VMWare tools into thinking the packages are gone. Apt thinks they are gone. Is there some service/file/cache/lock left that VMWare tools sees that makes it think that VMWare tools are still installed? I've googled and googled but there is no answer to this question with my particular circumstances on the interwebs. VMWare's documentation of this error is minimal.

  Read the article

• Can't get Apache 2.2.21 to compile with OpenSSL support

  - by angstwad

  Alright -- having a bad couple days here compiling Apache 2.2.21 on CentOS 5.7 with the following configure commands: ./configure --enable-ssl=shared --with-ssl=/usr/local/openssl I've compiled from source OpenSSL 1.0.0e from source: ./config --prefix=/usr/local --openssldir=/usr/local/openssl shared zlib-dynamic I attempt to start Apache and it returns: httpd: Syntax error on line 54 of /usr/local/apache2/conf/httpd.conf: Cannot load /usr/local/apache2/modules/mod_ssl.so into server: /usr/local/apache2/modules/mod_ssl.so: undefined symbol: SSL_get_servername If I look at how the libraries are linked, this is what I get: [root@web1 modules]# ldd mod_ssl.so libssl.so.6 => /lib64/libssl.so.6 (0x00002aaaaace4000) libcrypto.so.6 => /lib64/libcrypto.so.6 (0x00002aaaaaf30000) libdl.so.2 => /lib64/libdl.so.2 (0x00002aaaab281000) libz.so.1 => /lib64/libz.so.1 (0x00002aaaab486000) libpthread.so.0 => /lib64/libpthread.so.0 (0x00002aaaab69a000) libc.so.6 => /lib64/libc.so.6 (0x00002aaaab8b5000) libgssapi_krb5.so.2 => /usr/lib64/libgssapi_krb5.so.2 (0x00002aaaabc0e000) libkrb5.so.3 => /usr/lib64/libkrb5.so.3 (0x00002aaaabe3c000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x00002aaaac0d1000) libk5crypto.so.3 => /usr/lib64/libk5crypto.so.3 (0x00002aaaac2d4000) /lib64/ld-linux-x86-64.so.2 (0x0000555555554000) libkrb5support.so.0 => /usr/lib64/libkrb5support.so.0 (0x00002aaaac4f9000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x00002aaaac702000) libresolv.so.2 => /lib64/libresolv.so.2 (0x00002aaaac904000) libselinux.so.1 => /lib64/libselinux.so.1 (0x00002aaaacb19000) libsepol.so.1 => /lib64/libsepol.so.1 (0x00002aaaacd32000) Basically, I've tired compiling from source OpenSSL (both 0.9.8r and 1e), having yum reinstall from the repos, done a make clean and remade both OpenSSL and Apache numerous times -- but I can't get it to compile into the apache base or dynamically as a shared object file. What am I doing wrong here? Update 1: After doing a make clean and make distclean, I've reconfigured with the same parameters as above without any effect. The config.log is at Pastebin. Update 2: Modifying the LD_LIBRARY_PATH had no effect on the lib-deps of mod_ssl.so. UPDATE 3: I've compiled and recompiled many times, and verified with ldconfig that the OpenSSL libs dir is in my path, and included in ld.so.conf. Still cannot get httpd/mod_ssl to load the library at runtime.

  Read the article

• How to move a ruby on rails application to a new server

  - by ManiacZX

  I have a rails app on an old Ubuntu server I need to move onto a new machine. I haven't worked with ruby on rails so I don't really know anything about the structure of the app. I want to load this onto an Ubuntu 8.04 AMI on Amazon EC2 and am looking for any information regarding the migration process such as: Do I copy over the entire folder defined as the application root in the mongrel config (for ex: /u/apps/myapp/current) or just certain folders? Am I looking for trouble if I go with the latest versions of ruby and the various gems? Any general gotchas to look out for in the process. Current server information: root@webnode001:/# cat /proc/version Linux version 2.6.15-27-server (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP Fri Dec 8 18:43:54 UTC 2006 root@webnode001:/# rails -v Rails 1.2.3 root@webnode001:/# mongrel_rails cluster::configure --version Version 1.0.1 root@webnode001:/# gem -v 0.9.0 root@webnode001:/# gem list -l *** LOCAL GEMS *** actionmailer (1.3.3, 1.2.5) Service layer for easy email delivery and testing. actionpack (1.13.3, 1.12.5) Web-flow and rendering framework putting the VC in MVC. actionwebservice (1.2.3, 1.1.6) Web service support for Action Pack. activerecord (1.15.3, 1.15.2, 1.14.4) Implements the ActiveRecord pattern for ORM. activesupport (1.4.2, 1.4.1, 1.3.1) Support and utility classes used by the Rails framework. cgi_multipart_eof_fix (2.1) Fix an exploitable bug in CGI multipart parsing which affects Ruby <= 1.8.5 when multipart boundary attribute contains a non-halting regular expression string. daemons (1.0.7, 1.0.5, 1.0.4, 1.0.2) A toolkit to create and control daemons in different ways eventmachine (0.7.2, 0.7.0) Ruby/EventMachine socket engine library fastercsv (1.2.0, 1.1.0) FasterCSV is CSV, but faster, smaller, and cleaner. fastthread (1.0) Optimized replacement for thread.rb primitives ferret (0.11.4) Ruby indexing library. gem_plugin (0.2.2, 0.2.1) A plugin system based only on rubygems that uses dependencies only mongrel (1.0.1, 0.3.13.4) A small fast HTTP library and server that runs Rails, Camping, Nitro and Iowa apps. mongrel_cluster (0.2.1) Mongrel plugin that provides commands and Capistrano tasks for managing multiple Mongrel processes. mysql (2.7) MySQL/Ruby provides the same functions for Ruby programs that the MySQL C API provides for C programs. piston (1.3.3) Piston is a utility that enables merge tracking of remote repositories. rails (1.2.3, 1.1.6) Web-application framework with template engine, control-flow layer, and ORM. rake (0.7.3, 0.7.1) Ruby based make-like utility. sources (0.0.1) This package provides download sources for remote gem installation swiftiply (0.5.1) A fast clustering proxy for web applications.

  Read the article

• Starting/Stopping Custom PHP Chat Server Linux Service (CentOS)

  - by chad

  I have been trying all night to get this service working properly. I created this script from a template and am very new to bash coding. I wrote a fully functioning chat server in php which runs endlessly, but now want to make it a dedicated service. I want to do this so that it starts on server boot and boots back up if possible when there are any down-times with the server. The issue is that I need this thing to run in a detached screen so that I can monitor packet data or send server commands via SSH when need-be. The main problem that i'm having is that it needs to have its own PID when it starts so that I can stop/restart it when needed. I am the type who grinds on coding until I figure it out, but this is so new to me that it seems the learning curve here is very steep and frustrating. Below is my code if anybody can please help me with this one, i've gotten so tired I can't even concentrate any more :( #!/bin/sh # # chatserver # # chkconfig: 345 20 90 # description: chatServer Linux Service Daemon \ # for general server handling ### BEGIN INIT INFO # Provides: chatserver # Required-Start: $local_fs $network $named $syslog # Required-Stop: $local_fs $syslog # Default-Start: 3 4 5 # Default-Stop: 0 1 2 6 # Short-Description: This service maintains the chatServer # Description: chatServer Linux Service Daemon # for general server handling ### END INIT INFO # Source function library. . /etc/rc.d/init.d/functions exec="screen php -q /var/www/html/chatServer.php" prog="chatserver" config="/etc/sysconfig/$prog" pidfile="/var/run/chatserver.pid" [ -e /etc/sysconfig/$prog ] && . /etc/sysconfig/$prog lockfile=/var/lock/subsys/$prog start() { #$exec || exit 5 echo -n $"Starting $prog: " daemon $exec --name=$exec --pidfile=$pidfile retval=$? echo [ $retval -eq 0 ] && touch $lockfile return $retval } stop() { echo -n $"Stopping $prog: " killproc -p $pidfile rm -f $pidfile retval=$? echo [ $retval -eq 0 ] && rm -f $lockfile return $retval } restart() { stop start } reload() { restart } force_reload() { restart } rh_status() { # run checks to determine if the service is running or use generic status status $prog } rh_status_q() { rh_status >/dev/null 2>&1 } case "$1" in start) rh_status_q && exit 0 $1 ;; stop) rh_status_q || exit 0 $1 ;; restart) $1 ;; reload) rh_status_q || exit 7 $1 ;; force-reload) force_reload ;; status) rh_status ;; condrestart|try-restart) rh_status_q || exit 0 restart ;; *) echo $"Usage: $0 {start|stop|status|restart|condrestart|try-restart|reload|force-reload}" exit 2 esac exit $?

  Read the article

• postfix error: open database /var/lib/mailman/data/aliases.db: No such file

  - by Thufir

  In trying to follow the Ubuntu guide for postfix and mailman, I do not understand these directions: This build of mailman runs as list. It must have permission to read /etc/aliases and read and write /var/lib/mailman/data/aliases. Do this with these commands: sudo chown root:list /var/lib/mailman/data/aliases sudo chown root:list /etc/aliases Save and run: sudo newaliases I'm getting this kind of error: root@dur:~# root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo dur 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# tail /var/log/mail.log Aug 28 01:16:43 dur postfix/master[19444]: terminating on signal 15 Aug 28 01:16:43 dur postfix/postfix-script[19558]: starting the Postfix mail system Aug 28 01:16:43 dur postfix/master[19559]: daemon started -- version 2.9.1, configuration /etc/postfix Aug 28 01:16:45 dur postfix/postfix-script[19568]: stopping the Postfix mail system Aug 28 01:16:45 dur postfix/master[19559]: terminating on signal 15 Aug 28 01:16:45 dur postfix/postfix-script[19673]: starting the Postfix mail system Aug 28 01:16:45 dur postfix/master[19674]: daemon started -- version 2.9.1, configuration /etc/postfix Aug 28 01:17:22 dur postfix/smtpd[19709]: error: open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 01:17:22 dur postfix/smtpd[19709]: connect from localhost[127.0.0.1] Aug 28 01:18:37 dur postfix/smtpd[19709]: disconnect from localhost[127.0.0.1] root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~# root@dur:~# And am wondering what connection might be. I do see that I don't have the requisite files: root@dur:~# root@dur:~# ll /var/lib/mailman/data/aliases ls: cannot access /var/lib/mailman/data/aliases: No such file or directory root@dur:~# At what stage were those aliases created? How can I create them? Is that what's causing the error error: open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 01:17:22 dur postfix/smtpd[19709]: connect from localhost[127.0.0.1]?

  Read the article

• Trouble setting up PATH for Java on Debian

  - by milkmansrevenge

  I am trying to get Oracle Java 7 update 3 working correctly on Debian 6. I have downloaded and set up the files in /usr/java/jre1.7.0_03. I have also set the following two lines at the end of /etc/bash.bashrc: export JAVA_HOME=/usr/java/jre1.7.0_03 export PATH=$PATH:$JAVA_HOME/bin Logging in as other users and root is fine, Java can be found: chris@mc:~$ java -version java version "1.7.0_03" Java(TM) SE Runtime Environment (build 1.7.0_03-b04) Java HotSpot(TM) 64-Bit Server VM (build 22.1-b02, mixed mode) However there are two cases where Java cannot be found as detailed below. Note that both of these worked fine when I have previously installed OpenJDK Java 6 via aptitude, but I need Oracle Java 7 for various reasons. Most importantly, I cannot run commands as another user via su, despite the PATH showing that Java should be present. The user was created with adduser chris root@mc:~# su chris -c "echo $PATH" /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/java/jre1.7.0_03/bin:/bin root@mc:~# su chris -c "java -version" bash: java: command not found root@mc:~# su chris -c "/usr/java/jre1.7.0_03/bin/java -version" java version "1.7.0_03" ... How can it be in the PATH but not be found? Update 05/04/2012: explained by Daniel, to do with it being a non-interactive shell so files such as /etc/profile and /etc/bash.bashrc are not executed. Doing a full swap to that user and running Java works: root@mc:~# su chris chris@mc:/root$ java -version java version "1.7.0_03" ... I run a script on start up which exhibits similar but slightly different problems. The script is located in /etc/init.d/start-mystuff.sh and calls a jar: #!/bin/bash # /etc/init.d/start-mystuff.sh java -jar /opt/Mars.jar I can confirm that the script runs on start up and the exit code is 127, which indicates command not found. Inserting a line to print/save the PATH shows that it is: /sbin:/usr/sbin:/bin:/usr/bin This second problem isn't as important because I can just point directly to the Java executable in the script, but I am still curious! I have tried setting the full PATH and JAVA_HOME explicitly in /etc/environment which didn't help. I have also tried setting them in /etc/profile which doesn't seem to help either. I have tried logging in and out again after setting PATH in the various locations (duh!). Anyway, long post for what will probably have a simple one line solution :( Any help with this would be greatly appreciated, I have spent far too long trying to fix it by myself. Motivation The first problem may seem obscure but in my system I have users that are not allowed SSH access yet I still want to run processes as them. I have a ton of scripts operating in this way and don't want to have to change them all.

  Read the article

• Areca 1280ml RAID6 volume set failed

  - by Richard

  Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I continue, here are the specs: Dedicated Server Machine Areca 1280ml RAID controller, Firmware 1.49 12x Samsung 1TB HDDs We configured one RAID6-set with 10 discs that contains one logical volume. We have two hot spares in the system. Today one HDD failed. This happens from time to time, so we replaced it. Upon rebuilding a second disc failed. Normally this is no fun. We stopped heavy IO-operations to ensure a stable RAID rebuild. Sadly the hot-spare disc failed while rebuilding and the whole thing stopped. Now we have the following situation: The controller says that the raid set is rebuilding The controller says that the volume failed It is a RAID 6 system and two discs failed, so the data has to be intact, but we cannot bring the volume online again to access the data. While searching we found the following leads. I don't know whether they are good or bad: Mirroring all the discs to a second set of drives. So we would have the possibility to try different things without loosing more than we already have. Trying to rebuild the array in R-Studio. But we have no real experience with the software. Pulling all drives, rebooting the system, changing into the areca controller bios, reinserting the HDDs one-by-one. Some people are saying that the brought the system online by this. Some are saying that the effect is zero. Some say, that they blew the whole thing. Using undocumented areca commands like "rescue" or "LeVel2ReScUe". Contacting a computer forensics service. But whoa... primary estimates by phone exceeded 20.000€. That's why we would kindly ask for help. Maybe we are missing the obvious? And yes of course, we have backups. But some systems lost one week of data, thats why we'd like to get the system up and running again. Any help, suggestions and questions are more than welcome.

  Read the article

• Installing Phusion Passenger 4.0.20 on Ubuntu 13.10

  - by tempestfire2002

  So I'm trying to install Passenger on the newest version of KUbuntu (13.10). I installed Apache2 using the apache2-mpm-worker package using the Muon Package Manager. And these are the commands I ran. rvmsudo gem install passenger rvmsudo passenger-install-apache2-module But I keep getting the following errors: [Fri Oct 18 15:52:13.227790 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_LOCK_DIR} is not defined [Fri Oct 18 15:52:13.227933 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_PID_FILE} is not defined [Fri Oct 18 15:52:13.227969 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_RUN_USER} is not defined [Fri Oct 18 15:52:13.227991 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_RUN_GROUP} is not defined [Fri Oct 18 15:52:13.228026 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_LOG_DIR} is not defined [Fri Oct 18 15:52:13.231737 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_RUN_DIR} is not defined [Fri Oct 18 15:52:13.232760 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_LOG_DIR} is not defined [Fri Oct 18 15:52:13.233043 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_LOG_DIR} is not defined [Fri Oct 18 15:52:13.233078 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_LOG_DIR} is not defined AH00526: Syntax error on line 74 of /etc/apache2/apache2.conf: Invalid Mutex directory in argument file:${APACHE_LOCK_DIR} -------------------------------------------- WARNING: Apache doesn't seem to be compiled with the 'prefork', 'worker' or 'event' MPM Phusion Passenger has only been tested on Apache with the 'prefork', the 'worker' and the 'event' MPM. Your Apache installation is compiled with the '' MPM. We recommend you to abort this installer and to recompile Apache with either the 'prefork', the 'worker' or the 'event' MPM. Press Ctrl-C to abort this installer (recommended). Press Enter if you want to continue with installation anyway. The result of my running apache2ctl -V is: Server version: Apache/2.4.6 (Ubuntu) Server built: Aug 9 2013 14:31:04 Server's Module Magic Number: 20120211:23 Server loaded: APR 1.4.8, APR-UTIL 1.5.2 Compiled using: APR 1.4.8, APR-UTIL 1.5.2 Architecture: 32-bit Server MPM: worker threaded: yes (fixed thread count) forked: yes (variable process count) Server compiled with.... -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=256 -D HTTPD_ROOT="/etc/apache2" -D SUEXEC_BIN="/usr/lib/apache2/suexec" -D DEFAULT_PIDLOG="/var/run/apache2.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="mime.types" -D SERVER_CONFIG_FILE="apache2.conf" As can be seen, the server is compiled with the worker MPM, so why is passenger complaining? And how do I solve the above errors (warnings, really, but to be safe, I'd like to not have any warnings)? Thanks.

  Read the article

• Vagrant reporting VirtualBox guest additions out of date

  - by DTest

  Fairly new to Vagrant, so bear with me if I don't understand the process. I downloaded a CentOS box off http://www.vagrantbox.es/ Started it up running VirtualBox 4.2.4 and got this message: [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 So I used the vbguest plugin to update the guest additions, then repackaged the box as suggested. Having replaced the old box and loading it up I get the same message about guest additions being outdated, but vbguest reports that they are up to date (the automatic vbguest update is disabled in my Vagrantfile): Vagrant::Config.run do |config| config.vm.box = "centos56_64" config.vbguest.auto_update = false config.vbguest.no_remote = true end And the commands: dtest$ vagrant up [default] Importing base box 'centos56_64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- 22 => 2222 (adapter 1) [default] Creating shared folders metadata... [default] Clearing any previously set network interfaces... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant dtest$ vagrant vbguest --no-install [default] Detected Virtualbox Guest Additions 4.2.4 --- OK. [default] Virtualbox Guest Additions on host: 4.2.4 - guest's version is 4.2.4 Since they appear to be updated after an install, I could ignore the message. But is it possible to get rid of it?

  Read the article

• Linux Fiber Channel Host Setup Basic

  - by Jim

  I've been googling for about 4 hours now with no luck. I am trying to setup a Linux server running Oracle Server 6.3 as a Fiber Channel host. And then connect it to a Dell Compellent Fibre Channel Host contain a 500GB Volume. The Oracle server itself contains two Brocade 815 FC HBAs. I've discovered their WWN(I think) via cat /sys/class/fc_host/host1/port_name 0x100000051efc3d85 cat /sys/class/fc_host/host2/port_name 0x100000051efc3d9f The next part is where I am at a loss. I've used iSCSI before...is FC the same deal where you have an initiator and a target? If so where do I specific that in linux? I'm also new to Fiber Channel as a protocol, so i am unsure what is needed to make a transaction? WWN and port ID? Similar to IP:Port combination in the Ethernet world. I've read alot regarding using systool, multipath, fc_transport commands, however none of these is recognized as a valid command from Oracle Server 6.3 Appreciate the guidance and assistance. I installed sccsi-target-utils and can now run rescan-scsi-bus and sg_map -x. rescan-scsi-bus.sh -l -w -r Host adapter 0 (megaraid_sas) found. Host adapter 1 ((null)) found. Host adapter 2 ((null)) found. Host adapter 3 (ata_piix) found. Host adapter 4 (ata_piix) found. Scanning SCSI subsystem for new devices and remove devices that have disappeared Scanning host 0 for SCSI target IDs 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15, LUNs 0 1 2 3 4 5 6 7 Scanning for device 0 2 0 0 .... OLD: Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC H700 Rev: 2.30 Type: Direct-Access ANSI SCSI revision: 05 Scanning for device 0 2 1 0 ... OLD: Host: scsi0 Channel: 02 Id: 01 Lun: 00 Vendor: DELL Model: PERC H700 Rev: 2.30 Type: Direct-Access ANSI SCSI revision: 05 Scanning host 1 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning for device 1 0 3 1 ... OLD: Host: scsi1 Channel: 00 Id: 03 Lun: 01 Vendor: COMPELNT Model: Compellent Vol Rev: 0505 Type: Direct-Access ANSI SCSI revision: 05 Scanning host 2 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning host 3 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning for device 3 0 0 0 ... REM: Host: scsi3 Channel: 00 Id: 00 Lun: 00 DEL: Vendor: TEAC Model: DVD-ROM DV-28SW Rev: R.2A Type: CD-ROM ANSI SCSI revision: 05 Scanning host 4 channels 0 for SCSI target IDs 0, LUNs 0 1 2 3 4 5 6 7 0 new device(s) found. 1 device(s) removed. and sg_map -x /dev/sg0 0 0 32 0 13 /dev/sg1 0 2 0 0 0 /dev/sda /dev/sg2 0 2 1 0 0 /dev/sdb /dev/sg4 1 0 3 1 0 /dev/sdc I'm not sure what this all means...

  Read the article

• Vagrant - Failed login, ssh not set up

  - by motleydev

  This question is two fold because somewhere in my attempts to solve the problem, I created a new one. First: I was trying to vagrant up using a Vagranfile based on the standard hashicorp/precise32 box. Everything worked up until default: SSH auth method: private key where it would eventually time out. Enabling gui in the Vagrantfile showed that the machine never actually logs in. I can use the standard user/pass and log in from that point but the vagrant up process still remains at that prior status. Here's where my understanding might be a little dim. I've tried setting auth method from the insecure_pass_key to my root ~/.ssh/id_rsa or whichever one I wanted to use. I'm not entirely sure where to put a copy of the public key or my authorized keys file. I've got a .vagrant.d folder in my user dir (I'm on OSX) which seems to contain the box images. I've got a .vagrant folder in my directory with the Vagrantfile which seems to contain the specific machine I am building off of. I've tried pouring over the docs and forums but I seem to be missing a key concept here. And Now: After a host of tips/tricks such as rolling back by VirtualBox install, uninstalling/reinstalling Vagrant and VritualBox several times, when I try to run vagrant ssh-config with a Vagrantfile based on the same hashicorp/precise32 it says that the box is not enabled for SSH. Specifically, this error: The provider for this Vagrant-managed machine is reporting that it is not yet ready for SSH. Depending on your provider this can carry different meanings. Make sure your machine is created and running and try again. Additionally, check the output of `vagrant status` to verify that the machine is in the state that you expect. If you continue to get this error message, please view the documentation for the provider you're using. So now I am slightly up a creek. Any help would be appreciated if not just clarifying a concept. Some pertinent info: I'm on OSX Maverics Due to the fact I'm running a dual HD system with system files on one HD and user files on another, my permissions are a little wonky and VBoxManage will only let me run commands via Sudo - not sure if it's pertinent - but maybe. I have no idea what I'm doing. That part is perhaps more important.

  Read the article

• How can I force a merge of all WAL files in pg_xlog back into my base "data" directory?

  - by Zac B

  Question: Is there a way to tell Postgres (9.2) to "merge all WAL files in pg_xlog back into the non-WAL data files, and then delete all WAL files successfully merged?" I would like to be able to "force" this operation; i.e. checkpoint_segments or archiving settings should be ignored. The filesystem WAL buffer (pg_xlog) directory should be emptied, or nearly emptied. It's fine if some or all of the space consumed by the pg_xlog directory is then consumed by the data directory; our DBA has asked for WAL database backups without any backlogged WALs, but space consumption is not a concern. Having near-zero WAL activity during this operation is a fine constraint. I can ensure that the database server is either shut down or not connectible (zero user-generated transaction load) during this process. Essentially, I'd like Postgres to ignore archiving/checkpoint retention policies temporarily, and flush all WAL activity to the core database files, leaving pg_xlog in the same state as if the database were recently created--with very few WAL files. What I've Tried: I know that the pg_basebackup utility performs something like this (it generates an almost-all-WALs-merged copy of a Postgres instance's data directory), but we aren't ready to use it on all our systems yet, as we are still testing replication settings; I'm hoping for a more short-term solution. I've tried issuing CHECKPOINT commands, but they just recycle one WAL file and replace it with another (that is, if they do anything at all; if I issue them during database idle time, they do nothing). pg_switch_xlog() similarly just forces a switch to the next log segment; it doesn't flush all queued/buffered segments. I've also played with the pg_resetxlog utility. That utility sort of does what I want, but all of its usage docs seem to indicate that it destroys (rather than flushing out of the transaction log and into the main data files) some or all of the WAL data. Is that impression accurate? If not, can I use pg_resetxlog during a zero-WAL-activity period to force a flush of all queued WAL data to non-WAL data? If the answer to that is negative, how can I achieve this goal? Thanks!

  Read the article

• Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

  - by Max Kosyakov

  Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

  Read the article

• Creating a USB stick for installing centos 6.x using DVD1 and DVD2 iso files

  - by user250563

  First, we create 2 partitions on the USB stick that is let's say 16GB. first partition is let's say only 1GB and the second partition is the rest of what is available. after we "w" write the changes, the USB now has 2 partitions. 1 is 1GB 1 is more than 14GB so , we have... sdb1 and sdb2 now. now we need to turn these partitions into filesystems some say i should run these commands after those procedures. mkfs.vfat -F 32 /dev/sdb1 mkfs.ext3 /dev/sdb2 but some web pages recommend using: mkfs.vfat -n BOOT /dev/sdb1 mkfs.ext2 -m 0 -b 4096 -L DATA /dev/sdb2 which is it? so let's say the DVDs are called: CentOS-6.4-x86_64-bin-DVD1.iso CentOS-6.4-x86_64-bin-DVD2.iso so we make a directory: mkdir -p /mnt/dvd1 and then mount it: mount -o loop CentOS-6.4-x86_64-bin-DVD1.iso /mnt/dvd1 and i suppose we don't make a directory for dvd2 and we don't have to mount it ? at this point i do not know what should be done. but i think this step might be next: we make the USB bootable by finding the file named mbr.bin and then moving it to there via these commnad. dd conv=notrunc bs=440 count=1 if=/usr/lib/syslinux/mbr.bin of=/dev/sdb parted /dev/sdb set 1 boot on in other words we are "dd-ing it to 'sdb' not sdb1' or 'sdb2'. and then we use parted to set the boot to on for sdb so far everything looks good? here is the confusing parts.. how exactly do i move these iso files to the usb drive? EVERYTHING BELOW IS A GUESS. so at this point i should copy the folder /mnt/dvd1/isolinux to usb's sdb1 or sdb2 ? rename it to syslinux ? and then inside this syslinux folder there will be a file called... isolinux.cfg ? which should be renamed to syslinux.cfg ? and then copy the contents of /mnt/dvd1/images/* to USB's sdb2 ? but i think i am also suppose to copy and paste the both CentOS-6.4-x86_64-bin-DVD1.iso CentOS-6.4-x86_64-bin-DVD2.iso somewhere into this USB's sdb2 partition, correct ? almost like a drag and drop kind of a thing? or do they go into any folders ? centos' own web site has some instructions but those instructions do not work. http://wiki.centos.org/HowTos/InstallFromUSBkey i once got this working but things got ruined, i have to do it again and this time take notes.

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• When running a shell script, how can you protect it from overwriting or truncating files?

  - by Joseph Garvin

  If while an application is running one of the shared libraries it uses is written to or truncated, then the application will crash. Moving the file or removing it wholesale with 'rm' will not cause a crash, because the OS (Solaris in this case but I assume this is true on Linux and other *nix as well) is smart enough to not delete the inode associated with the file while any process has it open. I have a shell script that performs installation of shared libraries. Sometimes, it may be used to reinstall versions of shared libraries that were already installed, without an uninstall first. Because applications may be using the already installed shared libraries, it's important the the script is smart enough to rm the files or move them out of the way (e.g. to a 'deleted' folder that cron could empty at a time when we know no applications will be running) before installing the new ones so that they're not overwritten or truncated. Unfortunately, recently an application crashed just after an install. Coincidence? It's difficult to tell. The real solution here is to switch over to a more robust installation method than an old gigantic shell script, but it'd be nice to have some extra protection until the switch is made. Is there any way to wrap a shell script to protect it from overwriting or truncating files (and ideally failing loudly), but still allowing them to be moved or rm'd? Standard UNIX file permissions won't do the trick because you can't distinguish moving/removing from overwriting/truncating. Aliases could work but I'm not sure what entirety of commands need to be aliased. I imagine something like truss/strace except before each action it checks against a filter whether to actually do it. I don't need a perfect solution that would work even against an intentionally malicious script. Ideas I have so far: Alias cp to GNU cp (not the default since I'm on Solaris) and use the --remove-destination option. Alias install to GNU install and use the --backup option. It might be smart enough to move the existing file to the backup file name rather than making a copy, thus preserving the inode. "set noclobber" in ~/.bashrc so that I/O redirection won't overwrite files

  Read the article

• grep simply fails when used on a few files

  - by Reid

  I've been trying for about the past 30 minutes to get this to work properly. grep is not exactly the most difficult thing to use, so I'm somewhat baffled as to why this won't work. The files I'm trying to use grep on are simple XHTML log files. Their names are in the format [email protected], though I don't think that should matter, and inside is simple XHTML. I copied one such log file to be testfile so you can see the output of some commands and why it's baffling to me: [~/.chatlogs_windows/dec] > whoami reid [~/.chatlogs_windows/dec] > type grep grep is /bin/grep [~/.chatlogs_windows/dec] > uname -a Linux reid-pc 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:32:27 UTC 2010 x86_64 GNU/Linux [~/.chatlogs_windows/dec] > head -1 /etc/issue Linux Mint 10 Julia [~/.chatlogs_windows/dec] > ls -Alh | grep testfile -rw-r--r-- 1 reid reid 63K 2011-01-10 12:45 testfile [~/.chatlogs_windows/dec] > tail -3 testfile </body> </html> [~/.chatlogs_windows/dec] > file testfile testfile: XML document text [~/.chatlogs_windows/dec] > grep html testfile [~/.chatlogs_windows/dec] > grep body testfile [~/.chatlogs_windows/dec] > grep "</html>" testfile [~/.chatlogs_windows/dec] > grep "</body>" testfile [~/.chatlogs_windows/dec] > cat testfile | grep html [~/.chatlogs_windows/dec] > cat testfile | wc -l 231 [~/.chatlogs_windows/dec] > cat testfile | tail -3 </body> </html> [~/.chatlogs_windows/dec] > chmod a+rw testfile && ls -Alh | grep testfile -rw-rw-rw- 1 reid reid 63K 2011-01-10 12:45 testfile [~/.chatlogs_windows/dec] > grep html testfile That's what I'm attempting to do. I want to just use grep -ri query . in ~/.chatlogs_windows, which normally works perfectly for me... but for some reason, it completely fails at going through these files. If it matters, I copied these files off of my Windows 7 partition. But I chown'd them and gave myself all the appropriate permissions, and other programs (like cat) seem to read them just fine. I also copied testfile to testfile_unix and converted the line endings and tried that, but it didn't work either. I'm using zsh, but I tried it on bash and that failed too. Also, grep works normally: I tried it out on my documents folder and it worked flawlessly. If you need any more information, just let me know. I tried googling around, but I found no reason for grep to simply not work. Thanks in advance.

  Read the article

• How to change key mappings in Cygwin's Vim

  - by Boldewyn

  I'm using Vim under Debian, Win Vista and WinXP (the latter two with Cygwin). To handle tabs more easily, I mapped <C-Left> and <C-Right> to :tab(prev|next). This mapping works like a charm on the Debian machine. On the Windows machines, however, pressing <C-Left> deletes 5 lines, as far as I can tell, and meddles with cursor position, while <C-Right> does this, too, and additionally enters Insert mode. Question: To put it in a nutshell, how can I find out, why Vim behaves as it does? Is there a way to backtrace the active commands and keystrokes? Could there be a plugin the culprit? (I didn't install one, perhaps a default include by the Cygwin distro...) If so, how can I find it? Edit 1: OK, it seems, that I got a first trace: The terminal sends for <C-Left> '^[[1;5D', and for right '^[[1;5C' (evaluated with the <C-V><C-Left> trick). If vim interprets this literally and discards the first characters, it explains the strange behaviour. Any ideas, how I could change this key mapping? Additional Diagnosis: This behaviour occurs regardless of any existing ~/.vimrc file (is therefore not related to my above mentioned mapings) and is not inherited of some /etc/vim/vimrc, since this doesn't exist in the default Cygwin installation. :verbose map doesn't yield any new insights. Either nothing or my mentioned mappings appear, based on the existence of the .vimrc file :help <C-Left> suggests, that the default would be a simple cursor movement, which is apparently not the case. Vim's version under Cygwin: VIM - Vi IMproved 7.2 (2008 Aug 9, compiled Feb 11 2010 17:36:58) Included patches: 1-264 Compiled by http://cygwin.com/ Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver -clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +cryptv +cscope +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +postscript +printer +profile -python +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/share/vim" Compilation: gcc -c -I. -Iproto -DHAVE_CONFIG_H -g -O2 -D_FORTIFY_SOURCE=1 Linking: gcc -L/usr/local/lib -o vim.exe -lm -lncurses -liconv

  Read the article

• How to find out Vim's currently mapped commandos

  - by Boldewyn

  I'm using Vim under Debian, Win Vista and WinXP (the latter two with Cygwin). To handle tabs more easily, I mapped <C-Left> and <C-Right> to :tab(prev|next). This mapping works like a charm on the Debian machine. On the Windows machines, however, pressing <C-Left> deletes 5 lines, as far as I can tell, and meddles with cursor position, while <C-Right> does this, too, and additionally enters Insert mode. Question: To put it in a nutshell, how can I find out, why Vim behaves as it does? Is there a way to backtrace the active commands and keystrokes? Could there be a plugin the culprit? (I didn't install one, perhaps a default include by the Cygwin distro...) If so, how can I find it? Additional Diagnosis: This behaviour occurs regardless of any existing ~/.vimrc file (is therefore not related to my above mentioned mapings) and is not inherited of some /etc/vim/vimrc, since this doesn't exist in the default Cygwin installation. :verbose map doesn't yield any new insights. Either nothing or my mentioned mappings appear, based on the existence of the .vimrc file :help <C-Left> suggests, that the default would be a simple cursor movement, which is apparently not the case. Vim's version under Cygwin: VIM - Vi IMproved 7.2 (2008 Aug 9, compiled Feb 11 2010 17:36:58) Included patches: 1-264 Compiled by http://cygwin.com/ Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver -clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +cryptv +cscope +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +postscript +printer +profile -python +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/share/vim" Compilation: gcc -c -I. -Iproto -DHAVE_CONFIG_H -g -O2 -D_FORTIFY_SOURCE=1 Linking: gcc -L/usr/local/lib -o vim.exe -lm -lncurses -liconv

  Read the article

< Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >