Search Results

Search found 13955 results on 559 pages for 'easy angel'.

Page 416/559 | < Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• Setting the default permissions for files uploaded via FTP to a directory

  - by Kerri

  Disclaimer: I'm just a web designer/coder, and server admin stuff is my weakest point of them all. So be easy on me (and very specific). I'm using a simple CMS (Unify) on a site, where part of the functionality is that the client can upload files to a specified directory (using FTP). The permissions for the upload directory are set to 755. But when files are uploaded through the interface, they are uploaded with permissions set to 640 (instead of 644), so site visitors cannot acces the files. When I emailed the CMS's support about this, they told me that it was a server setting, and I need to make sure that files uploaded through FTP are set to 644. Makes perfect sense, but I have no idea how to do this. Any help would be greatly appreciated. This site is a shared site hosted by Network Solutions (Unix), so my access options are limited. I can edit .htaccess files, and php.ini, but that's about all I have access to. It appears I can't even log on via shell. ETA: 11/11/2010 Thanks all. I was able to work around this problem by setting up the CMS's settings in a different way. I'd be interested in following up on Nick O'Niel's suggestions, because I think he's on the right track, but unfortunately I can't access the necessary files on this particular server. So, anyway, I'm leaving this open, since the original questions isn't exactly resolved. Unfortunately, I probably can't put a correct answer to the test, since the shared server in question has nearly all of its config files tightly locked down.

  Read the article

• GlusterFS as elastic file storage?

  - by Christopher Vanderlinden

  Is there any way to run GlusterFS in a replicated mode, but with the ability to dynamically scale the volume up and down? Say you have 3 servers all running glusterd. your Gluster volume would have to be setup with replica 3 gluster volume create test-volume replica 3 192.168.0.150:/test-volume 192.168.0.151:/test-volume 192.168.0.152:/test-volume You would then mount it as say \mnt\gfs_test What happens when I want to add 2 more servers to the storage pool and then also use them in this volume? Is there any easy way to expand the volume AND increase that replica count to 5? My end goal is to run this on EC2 instances, say 3 Apache front ends, with the webroot setup on the gluster volume mount. My concern is that if I ever need to spin up a server, I would want the server to not only be an additional Apache front end, but also another server in the gluster file system, adding to fault tolerance as well as possibly giving a slight boost in read speed. Maybe there are better options that would fit the bill here? Thanks.

  Read the article

• Quickly set up a Windows Server and automatically install and configure software

  - by Chris

  Yesterday I spent far too much time downloading and installing software on Windows Server 2008. I only had to install a simple server for SQL Server 2008 Express using Microsoft's Web Platform Installer, then configure it to enable remote connections. Everything had to be attended, wasting my time. On a Linux system, this would be trivial to automate, but this is Windows. I do this very rarely, but in the future I would like to make this take as little time as possible. I could do a disc image with everything I installed and configured, but is there a better way? I know nothing of advanced deployment techniques on Windows. Ideally I would like to be able to remotely re-install the OS, or have an unattended install (which I know is possible). Any tips to make the software I need easier to and install and configure with minimal interaction necessary would be helpful. I don't expect everything I asked for to be possible and easy to do. Basically, If any part of it can be done quicker or at least without user input, that's what I'm looking for.

  Read the article

• Multidimensional data table?

  - by ShreevatsaR

  [Apologies if this sort of question is off-topic for SuperUser. Please redirect to the right place if so.] There is a 3-dimensional array of values. (That is, instead of a table/2-dimensional array with values in a grid, the values can be thought of in a cube instead.) Is there a way to display this "cube" interactively, ideally on a webpage? Specifically, given the data, it would work something like this: the user selects two of the 3 variables. He then sees a "stack" of tables, one for each value of the third variable (cross-sections, in other words). By selecting the appropriate table from the stack, he can see the (i,j,k) value he wants. The "technology" for displaying such a thing (stacked tables, rotation, etc.) already exists, so this seems the sort of thing that someone ought to have written already. To be clear: I don't need sophisticated graphics necessarily, just the ability to select from cross-sections of variables. But I have no experience with (say, for displaying on a webpage) what web gadgets exist, so I'm clueless how to even search for one. (Google searches like "multidimensional data visualization" didn't throw up anything useful. Google Spreadsheets can do a few kinds of charts which can be embedded on a webpage, but I cannot tell if this is one of them.) [I can imagine how it ought to work for higher dimensions. For four-dimensions, instead of selecting just a stack, you'd first select an (i,j) from an "outer table", which would show all (k,l) values for that (i,j). For higher dimensions, inductively: you select (i,j), and then repeat what you'd do with 2 fewer dimensions.] So has this been written? Is this easy to write? Where ought one to look for such a thing?

  Read the article

• Get Safari to use different autocompletion on different URLs on same hostname

  - by Luke404

  I have a webserver publishing different services over the same SSL VirtualHost, the two most commonly used being PhpMyAdmin and Cacti. These (and others) use 'cookie' style authentication, asking user and password in an HTML form (thus not using HTTP Authentication). Being on the same hostname, the Safari browser didn't manage too well stored passwords: if I login to one app with user foo, and then go to app two it would propose me user foo and its password in the login form. Changing just the username to bar used to be sufficient to let Safari autocomplete the correct password in its form field. Annoying, but I could live with it - usernames are short and easy to remember when compared to the passwords we use. After the update to safari5 this seems to be no longer true: if I store in safari (actually user keychain on OSX) credentials for https://www.foobarbaz.com/app1 AND credentials for https://www.foobarbaz.com/app2 there seem to be no way for it to autocomplete both based on the url. Even editing the keychain to add the path (it will store only the hostname by default) does not help. Is there anything I can do to let it work the way I want while still keeping everything on one hostname? Modifying anything server side is of course possible, but I can't switch apps to HTTP Auth (and not every one will support it anyway) to use different 'realms'.

  Read the article

• Delegating account unlock rights in AD

  - by ewall

  I'm trying to delegate the rights to unlock user accounts in our Active Directory domain. This should be easy, and I've done it before... but every time the user tries to unlock an account (using the LockoutStatus tool), he gets denied with the error "You do not have the necessary permissions to unlock this account." Here's what I've done: I created a domain local group and added the members who should have the rights. This was created over a week ago, so the users have logged out and in again. In ADUC, I've used the Delegate Rights wizard on the OU which contains our user accounts to grant permissions to Read lockoutTime and Writer lockoutTime to the group, per MSKB 279723 I have double-checked the permissions were applied correctly in ADSIEdit. I have forced replication between all domain controllers to ensure the permission changes were copied over. The user testing it has logged out and in again to ensure he has any changes applied to his account. ...That covers all the bases I can think of. Anything else I could be missing?

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• Load balancing with puppet

  - by Gonçalo Queirós

  Hi there. Im trying to setup a loadbalancing system. My load balancer (nginx) has a conf file where i should list all IP's of the upstream servers. I could put the IP's on the conf manually, but this ways i would need to change the conf file every time i add/remove an upstream server. For now i came up with two different ideas, but i don't like much of neither: 1 - Have every upstream machine to use Exported Resources to create a file with it's IP..Then the load balancer server will have an "include conf_directory/*", and load all the files created by the upstrem servers. Since the load balancer is using nginx this can be done, but if i wan't latter on to configure something that doesn't have the "include" on the conf files, this solution will not work. 2 - If the config doesn't support the "include" command, then we could have again, every upstream server use the Exported Resources to create a filw with its IP, and latter on, the load balancer execute a command that would pick every file and generate the config Both versions addopt the same techinque, the difference is that version 2 is used when the server (that needs to have a conf generated) doesn't recognize a command like "include" inside its own conf. Now, my question is, is there any way to do this in a different form? I suspect that there is, since puppet is made to manage multiple servers, it seems a bit strange not have a easy way to configure load balancers.

  Read the article

• How do I rename my old Program Files folder?

  - by SteveJ

  I installed a new SSD as my boot drive (C:), installed a fresh version of Windows 7 64-bit, and kept my existing SATA drive in the system (D:). I want to keep using my D: drive for file storage (no sense filling up the SSD with stuff that isn't performance critical) and I haven't formatted the D: drive because there's stuff on there I want to keep. I also want to create a new "D:\Program Files" folder so I can install apps that aren't performance-critical there. So I decided I'd rename the existing "D:\Program Files" from my old Windows install to "D:\Old Program Files" and then create a new "D:\Program Files" directory. Easy, right? I can see "D:\Program Files" just fine in Explorer. I right click, select Rename, and type "Old Program Files." I get the alert that says I need Admin permission to do this, so I press the confirm button with the shield. But the folder still appears as "Program Files" in Explorer. I jump out to the command line, and it appears as "Old Program Files" when I do a dir. I can even do mkdir "Program Files" and when I do a dir they both appear. But in the Explorer GUI, it looks like I have two "Program Files" folders. This will be confusing during app installation because I won't be able to tell which one is which. I've tried poking around in the properties tab of the old folder, but can't find anything that would explain what's causing the issue. How do I rename the old Program Files folder?

  Read the article

• First web server questions

  - by Graeme

  Hi there, Just looking for some help/suggestions with this. I require my own server for an upcoming project that will be hosting users websites. I want to build a control panel the user can log into and modify their website which will be stored elsewhere on the server. This all seems easy enough, It's just managing domains and emails that confuse me. What should I look for to manage domain names and point them to the correct website and also what would be the best way to manage email accounts/set up new ones etc. I want to avoid cPanel/WHM if possible, I'm looking to control most things through the control panel I will be building. So any suggestions on this would be useful as well, as I will be wanting to add email accounts through php (Can be done using a shell I assume?). I will also be wanting to measure bandwidth used on the websites contained in each users directory, any suggestions on making this possible? I'm really looking for some suggestions on what software to use to set this up, any advice would be really helpful! Thanks, Graeme

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• How to slow down audio files?

  - by verve

  I need a program (with an easy learning curve) that lets me slow down mp3 (at the very least this format) music and audiobook files. The software needs to be able to slow down the audio at the chosen speeds without altering the pitch and accuracy of the words being pronounced. Perhaps like the language software "Byki Deluxe's" "SlowSound" feature? I'm learning a foreign language (German) and I find the speeds at which the books are being read too fast. I need to hear the pronunciation of each word much more clearly to learn how to pronounce the words myself. Is there such a product out there? Now, I know you can slow down stuff in VLC but it sounds really artificial. I need something that slows down audio files without altering the accuracy of the words being pronounced. It doesn't have to be freeware; ease of use and quality is more important to me. Win 7 64-bit. IE 8. Edit: Are there any software-for-pay like Audacity? Only the beta works in Win 7. Also, I'd prefer to be able to slow down a file live and not have to create a new file to use the feature.

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by nfm

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• Apple: Bind a key to a commandline command?

  - by Stefan Lasiewski

  I have a Mac Powerbook running Leopard (10.5.8). Does Leopard provide an easy way to bind keys to commands which are typically run on the commandline? For example, I can open up Terminal.app and run the command /System/Library/Frameworks/ScreenSaver.framework/Resources/ScreenSaverEngine.app/Contents/MacOS/ScreenSaverEngine which will activate the screensaver and lock my screen. What if I want to bind 'Apple-key L' to this command and execute this globally, regardless of which application is in use at the moment? Can I do this, or can I only run ScreenSaverEngine from a Terminal window? I tried to set up global keyboard shortcuts, but it seems that this won't allow me to bind a key to an arbitrary shell command: Note: You can create keyboard shortcuts only for existing menu commands. You cannot define keyboard shortcuts for general purpose tasks such as opening an application or switching between applications. I tried to set up a application keyboard shortcut, but commands like ScreenSaverEngine don't seem to be an application. Note that this Screensaver/Lock screen is just one example. I have come across other nifty commands which I might want to bind to a key-combination as well. I can do this in Gnome and Windows (with varying success). How about with Leopard?

  Read the article

• How best to manage my growing data in Excel?

  - by Mike

  This isn't a question about formulas or features in Excel. I'm debating the correct/best way to manage the growing amount of data 'I have to' manage in Excel (I produce PIVOT tables/reports for my management). DATA: I record the number of publications we order: cost, date ordered, start and end of subscription, who requested it, when they ordered it, when I ordered it, will it be cancelled next year, etc, etc, etc. DILEMMA: Obviously we re-order a lot of the same publications, so depending on how I manage the data I could be duplicating all over the place. OPTION 1: So, do I use ROWs = publication name in Row 1 and all the related columns for each financial year are copied and pasted after each financial year ready for the new FY information? This will lead to me going to column ZZ. OPTION 2: Or, do I use COLUMNs = each row has only one FY information for each publication and if we re-order or cancel a publication I re-type the publication name in a row below and fill in appropriate columns? This will lead to a long list of publications down to row 10000, and potential for misspelling of repeat ordered publication names. IDEAS: What's the best way - thinking in terms of pivot table best practice, being able to sum or count easy, report formatting, etc. Any best practices much appreciated.

  Read the article

• Change default profile directory per group

  - by Joel Coel

  Is it possible to force windows to create profiles for members of one active directory group in a different folder from members in another active directory group? The school here uses DeepFreeze to protect public computers. In a nutshell, DeepFreeze prevents all changes to a hard drive such that every time you restart the machine the disk is identical to it was at the time you froze it. This is a bit different than restoring to an image, in that it never really wrote changes to disk in a permanent way in the first place. This has a few advantages over images: faster recover times, and it's easy to thaw the machine for a few minutes to perform maintenance such as windows updates (which can even be automated). DeepFreeze also allows you to configure a "thawspace" partition, where changes are persistent across reboots. One of the weaknesses of DeepFreeze is that you end up needing to create a new profile every time you log in, unless your profile existed at the time the machine was frozen. And even then, any changes you make to your profile while working on a frozen machine are lost. As students have frequent legitimate needs to log in to our classroom machines, there is currently a lot of cleanup involved from time to time in removing their old profiles and changes, so I want to extend DeepFreeze to protect our classroom computers as well as public computers. The problem is that faculty have a real need to keep a stateful profile locally on these classroom computers. The solution I would like to use is to configure Windows via group policy (or even manually, if that's the way I'll have to do it) to place profile folders on the thawspace partition, but only for members of the faculty security group. Is this possible?

  Read the article

• Which Revision Control Software to use for Personal Dropbox?

  - by wag2639

  I want to set up a sync repositiory that would be similar to Dropbox. Goals/Requirements: Free (Open Source very preferable) Linux host (probably Ubuntu) Windows/Mac/Linux clients Potential for multiple users with limited access (optional) Preferable easy, doesn't necessarily need to be automatic Revision control very preferable Basically, I want to be able to use multiple computers, possible with different OS's, and be able to access, use, and sync files across all of them. I also want to have a local copy of the repository for when I'm not connected to the network (as if I'm working on a laptop, I want to keep a local repository to keep revision and merge later with "master" repository). For example, I'm editing a few pictures on my laptop during the day outside of my network, but when I get home, I would like to sync the changes, including incremental changes, with my desktop at home. I would also like my roommates to be able to access and use this repository too but limit access to certain files. For example, I may want to use this to backup financial records but wouldn't want them to have access to those files. I'm a programmer and familiar with SVN but I know that wouldn't be the most appropriate since it doesn't handle binaries well and doesn't keep a local repository. I know better choices exist but I don't really know them well enough to choose the best one.

  Read the article

• Migrating Linux user data to Windows profiles automatically

  - by scott ryan

  I have what seems to be an incredibly simple problem with a very simple solution but I'm having some trouble connecting dots. I have an aging server running Ubuntu Server which hosts roaming profiles. I am switching to a Windows Server 2012 DS shortly. Users used to be named firstinitial.lastname and we are switching to firstname.lastname. I need to transfer things like favorites, documents, etc. from the roaming Linux profile to the user's local Windows profile. So, the way I think it'd work is by using a login script. I think I'd use a script to mount the Linux server's /home for each user, then do copy to various paths (documents, pictures, etc.). But, how do I automate this for each user that logs in? I'm working with a nonprofit, so doing this by hand would probably be out of their budget. I'm open to suggestions, though. What I want is basically Windows Easy Migration, but I'm fairly certain that won't work under Wine... (Kidding, I promise). Thanks!

  Read the article

• In Icinga (Nagios), how do I configure hosts with multiple IPs?

  - by gertvdijk

  I'm setting up Icinga (Nagios fork) and I have some machines with multiple interfaces. Some services are only listening on one of them and to check them correctly, I like to know if it's possible to have multiple IP addresses configured for a single host in Icinga. Here's a minimal example: Remote Server: eth0: 1.2.3.4 (public IP) eth1: 10.1.2.3 (private IP, secure tunnel) Apache listening on 1.2.3.4:80. (public only) OpenSSH listening on 10.1.2.3:22. (internal network only) Postfix SMTP listening on 0.0.0.0:25 (all interfaces) Icinga Server: eth0: 10.2.3.4 (private IP, internet access) Now if I define a host: define host { use generic-host host_name server1 alias server1.gertvandijk.net address 10.1.2.3 } This will not check the HTTP status correctly. And defining an additional host: define host { use generic-host host_name server1-public alias server1.gertvandijk.net address 1.2.3.4 } will check everything, but shows up as two independent hosts. Now I want to 'aggregate' these two hosts to show up as a single host, yet providing an easy configuration to check the services on their proper address. What is the most elegant number-of-configuration-lines-saving solution to this? I read about several plugins available to workaround this, but I can't figure out what is the current way to address it. Solutions go back to 2003, but I'm running Icinga 1.7.1, already capable of the address6 option, yet that triggers IPv6-only resolving on the hostname... Ideally, I wish to configure Icinga to be intelligent enough to know that the Postfix instance running on 10.1.2.3:25 is the same as 1.2.3.4:25 and thus not triggering two alarms. I guess this must have been tackled before and sysadmins have it set up now. Please share your solution to this. Thanks! :)

  Read the article

• Looking for a small, portable, port-mirroring ethernet switch.

  - by user37244

  I recently had a mac go haywire, taking half a minute or more to get www.google.com loaded. Getting its owner to give up the machine for repair was like pulling teeth - they were insisting that it must be something to do with the network, since so much had changed with the local configuration at about the same time their box went haywire. I eventually set up a port mirror to a box that I could remote to so I could show that the mac was only irregularly getting packets onto the network. Demonstrating this faced an additional challenge: the latency of the remote desktop software I was using meant that I had to point to timestamps instead of just the moment the packet flashed up on the screen as my evidence. This particular user was the reason this was so challenging this time around, but I would like to have a box that I can cart from desk to desk to use wireshark on my laptop at any station where I need it. 3com, cisco, netgear, etc. (ad nauseum), all make switches that can be configured for port mirroring, but in my case, the smaller, the better. For the sake of my sanity, I'll probably end up running it off a battery anyway. If my laptop had two ethernet ports, this would be easy. So, whaddya recommand for a device that requires 0 configuration at each powerup (though I'm fine with poking at it for a while to set it up initially.) Small, light, and cheap enough to get it past purchasing? Thanks,

  Read the article

• Did I miss anything when checking for passwords? [migrated]

  - by Keltari

  There's a bit of a story to this, so bear with me... I am looking for a new job and came across a posting for a computer forensics position. Its not really my field, but I thought I would apply anyway, just for fun. To make a longer story shorter, they want you to uncover as many passwords as you can find. I downloaded an image and dd'd it to a thumbdrive. The only thing visible was a text file, which contained a password. I knew there had to be more, so I used an undelete utility and found 2 deleted files. First there was another text file with a password - easy. The other was a .pst file which I mounted into outlook. There were some emails with passwords, as well as an email with an image. Another email has a link to a stegenography site. Obviously, there was a file hidden in the image, so I went to the website and downloaded the stegenography decoder. I had to try some of the passwords I had found to get the file to decrypt, and sure enough, there was another text file with a password. I called it a day at that point. Did I miss any other methods?

  Read the article

• Sharing music on NAS with other zunes and ipods

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40gb worth of music and my girlfriend has her iPod music library around 30gb. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (zune/ipod) seamlessly.

  Read the article

< Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >